QUARTINO_COP.indd 3
23-09-2011 13:34:51
Think wall We have designed a wallcovering to satisfy any decorative need.
QUARTINO_COP.indd 4
23-09-2011 13:34:56
Appropriate for use on almost any wallcovering application. Available in many ABET LAMINATI colours and ďŹ nishes.
Suitable for applications where acoustic deadening is needed but also valuable for its effective design due to the proďŹ led surface.
INGLESE_01_09.indd 1
15-09-2011 15:27:30
Parqwall®
2 Abet Laminati presents a “new look” called Parqwall®, which incorporates new technical mounting solutions. The cladding system is available with either vertical or horizontal panels in 400 mm or 600 mm widths (15 11/16” or 23 9/16”). Parqwall® is now available with both visible anodized aluminum joints and fold-away joints, which allow the cladding material to display a completely unbroken surface. Special joints have also been produced, which allow both horizontal and vertical fixing of shelves and coat racks. The installation procedure has been made considerably easy with the new profiles. New colours with no required minimum quantity have been added to the range.
For additional noise reduction, we recommend the attachment of an insulating material i.e. glass fibre, rock wool etc., to the wall surface.
INGLESE_01_09.indd 2
15-09-2011 15:27:31
The Parqwall® cladding system makes it possible to clad walls of any type and in any condition. It is easy to install and a quick solution to refurbishing problems in rooms for which there are no special restrictions regarding the subsequent use of the premises.
Parqwall
®
cladding system
with horizontal panels and visible anodized aluminum joints.
INGLESE_01_09.indd 3
3
15-09-2011 15:27:47
Parqwall®
4
Parqwall® cladding system with vertical panels and visible anodized aluminum joints.
The Parqwall® system can be installed directly on existing walls if they are sufficiently straight and dry. Should Parqwall® be installed on old, damp or uneven walls, it is recommended to leave a gap between the wall and the Parqwall® system. The Parqwall® system can be installed on vertical or horizontal wood spacers or on a galvanized steel frame (Knauf system or similar).
INGLESE_01_09.indd 4
15-09-2011 15:27:55
Parqwall® exhibits the same characteristics as those of a wooden panel, therefore it is important to ensure good ventilation behind the cladding panels.
When building the frame, remember that the Parqwall® panels should be mounted at a distance of at least 5 mm (3/16 in.) from the floor, to enable ventilation of the cavity behind. When cladding particularly damp walls, the Parqwall® panels should finish at a distance of at least 50 mm (1 15/16 in.) from the floor. This will protect the base of the panel from the risk of dampness being absorbed from the floor.
INGLESE_01_09.indd 5
5
15-09-2011 15:27:57
Silentwall®
6 Silentwall ® is a noise reducing component of the modular Parqwall ® system. Silentwall® is designed to absorb noise from highly frequented rooms, which have a high level of background disturbance.
Silentwall® is suitable for theatres, cinemas, auditoriums and convention halls where sound reduction is necessary.
INGLESE_01_09.indd 6
15-09-2011 15:27:58
Silentwall® is a noise reducing component of the modular Parqwall® system.
Silentwall
®
cladding
system with vertical panels and visible anodized aluminum joints.
INGLESE_01_09.indd 7
7
15-09-2011 15:28:07
8
Hanging accesoires Parqwall® Silentwall®
Rack joints allow the installation of several types of shelves. When the panels are fitted horizontally, the use of rack joints allow the installation of a wide range of coat racks for offices and shops.
Panels installed horizontally with rack joints. Panels installed vertically with the use of rack joints.
a
INGLESE_01_09.indd 8
b
15-09-2011 15:28:16
The special joints allow the installation of shelves and coat racks on the Parqwall® and Silentwall® systems.
Parqwall
®
cladding
system with vertical panels and the fitting of the rack joints.
INGLESE_01_09.indd 9
9
15-09-2011 15:28:27
10
Decors range Parqwall® Silentwall®
Parqwall® and Silentwall® are made of Print® high-pressure laminate (HPL) available in an extremely wide range of finishes, colours and wood effects.
Architects and interior designers can accomplish their projects without any aesthetic restrictions and with total creative expression. They can create bright, pleasant and very comfortable rooms, even in conditions where the existing architectural structure is particularly run down. Parqwall® and Silentwall® can be produced without any minimum quantity in the range shown here, designed to fulfill the most demanding market requests. However, it is possible to manufacture the Parqwall® and Silentwall® cladding systems in other colours and patterns offered in the ABET LAMINATI® HPL range. Attention: please kindly refer to the 2011>2014 ABET LAMINATI collection to confirm the availability of the chosen decor in the current range.
colours and texture
INGLESE_10_23.indd 10
410
854
810
418
413
Microline
Microline
Microline
Microline
Microline
869
893
473
477
870
871
476
Microline
Microline
Microline
Microline
Microline
Microline
Microline
479
420
868
867
846
458
857
Microline
Microline
Microline
Microline
Millerighe2
Millerighe2
Millerighe2
482
499
484
425
423
428
441
Millerighe2
Millerighe2
Millerighe2
Millerighe2
Millerighe2
Millerighe2
Millerighe2
23-09-2011 12:02:02
463
469
494
835
834
410
Millerighe2
Millerighe2
Millerighe2
Millerighe2
Millerighe2
Millerighe2
Grana2
409
457
443
444
1802
1803
858
Grana2
Grana2
Grana2
Grana2
Grana2
Grana2
Grana2
800
803
496
1804
472
476
1808
Grana2
Grana2
Grana2
Grana2
Grana2
Grana2
Grana2
867
893
837
410
406
810
418
Grana2
Grana2
Grana2
Lucida
Lucida
Lucida
Lucida
854
413
416
479
420
466
454
Lucida
Lucida
Lucida
Lucida
Lucida
Lucida
Lucida
1809
1810
472
879
421
406
812
Lucida
Lucida
Lucida
Lucida
Lucida
Grainwood
Grainwood
INGLESE_10_23.indd 11
colours and texture
460
11
15-09-2011 15:23:51
12
Decors range colours and texture
Parqwall® Silentwall®
869
868
867
893
837
897
879
Grainwood
Grainwood
Grainwood
Grainwood
Grainwood
Grainwood
Grainwood
410
406
411
810
409
Bianco Ghiaccio
Bianco Primavera
Bianco
Mini Bianco
Latte
421 Grainwood
colours
finitura Sei
INGLESE_10_23.indd 12
418
854
478
413
414
479
473
Panna Crema
Silver Bleu
Grigio Chiaro
Beige Ardenne
Sabbia
Grigio Tortora
Grigio Lapponia
495
475
420
869
1809
477
1819
Verde Grigiato
Grigio Perla
Beige Pastello
Grigio Alpaca
Azzurro Koala
Grigio
Grigio Monviso
480
870
868
1810
1820
867
871
Grigio Plomo
Grigio Lastra
Grigio Medio
Grigio Autunno
Grigio Cosmico
Grigio Cielo
Grigio Scuro
15-09-2011 15:23:54
colours
476
472
879
421
466
412
462
Grigio Inox
Grigio Londra
Grigio GraďŹ te
Nero
Mini Giallo
Avorio
Giallo Ananas
467
464
463
468
469
860
470
Giallo Paglierino
Giallo Chiaro
Giallo Pom-Pom
Giallo Canarie
Giallo Africa
Giallo Piper
Giallo Tigre
1801
862
1812
861
822
835
834
Giallo Ocra
Giallo Savana
Giallo Polenta
Giallo Pop
Melone
Arancio Canyon
Rosso Woom
432
823
431
435
828
827
866
Terra Ocra
Rosso Tango
Rosso
Rosso Antico
Rosa Baby
Rosa Singapore
Giallo Champagne
830
494
427
417
1813
813
415
Rosa Crazy Horse
Bouganville
Porpora
Rosso Terracotta
Magnolia
Beige Manhattan
Beige Chenise
416
829
812
843
842
446
Beige
Yaqui
Rosa Viola
Verde Pace
Verde Sub
Verde Pastello
INGLESE_10_23.indd 13
13 1816
Sahara Beige
15-09-2011 15:23:57
14
Decors range colours
Parqwall® Silentwall®
INGLESE_10_23.indd 14
892
893
894
837
898
897
1805
West Brown
Terra d’Ombra
Viola Fumo
Sarmiento
Bruno Fiandra
Bruno Vulcano
Rosa Nespola
890
887
891
1806
895
831
429
Darling Beige
Apricot Brown
Scotch Brown
Ruggine
Bruno Cherry
Rosso Mattone
Viola Cerise
424
836
1811
832
453
454
457
Viola Tramonto
Rosso Prugna
Rosso Barolo
Rosso Lord
Verde Papiro
Verde Caraibi
Verde Cenere
452
443
485
486
1802
841
846
Verde Lichene
Mini Verde
Azzurro Mary
Azzurro Lago
Verde Alga
Verdino
Turchese
458
444
445
459
497
491
492
Verde Libellula
Verde Salvia
Verde Chiaro
Verde Estate
Turchese Cobalto
Bleu Tundra
Verde Bond Street
1803
456
488
441
460
451
839
Verde Militare
Verde
Verde Prussia
Verde Cedro
Verde Erbetta
Sempreverde
Verde Acqua
15-09-2011 15:24:00
colours
437
490
438
845
440
450
455
Blu Giungla
Verde Mogul
Verde Mariaci
Verde Versailles
Verde Biliardo
Verde Lauro
Verde Ardizio
481
483
857
853
487
858
801
Celeste Mattino
Azzurro Maldive
Celeste Myosotis
Bleu Spazio
Azzurro Polvere
Azzurro Pervinca
Azzurro Tempesta
484
847
482
499
430
838
859
Blu ZafďŹ ro
Azzurro
Bleu Panarea
Bleu California
Lilla Gemini
Bleu Primario
Blu Faenza
1804
1818
851
428
496
849
1814
Blu Tenebre
Blu Intenso
Blu Cobalto
Blu Elettrico
Blu Esperia
Blu Pavone
Azzurro Acqua
856
850
1808
852
805
802
804
Blu Acciaio
Bleu Rada
Blu Petrolio
Big Bleu
Rosa Plumbeo
Blu Ice
Calendula
425
423
498
Lilla Erica
Viola Madras
Viola Giglio
INGLESE_10_23.indd 15
15
15-09-2011 15:24:03
16
Decors range Parqwall® Silentwall®
serie cresp 1422
1522
1419
1424
1524
Cresp
Cresp Due
Cresp
Cresp
Cresp Due
1420
1520
1413
1513
1421
1521
1415
Cresp
Cresp Due
Cresp
Cresp Due
Cresp
Cresp Due
Cresp
1515
1414
1410
1423
1523
1418
1518
Cresp Due
Cresp
Cresp
Cresp
Cresp Due
Cresp
Cresp Due
251
244
200
202
243
Lucida
Lucida
Lucida
Lucida
Soft
1087
1030
1089
1091
1086
vertical line finitura Sei
255
265
Soft
Soft
fiber
INGLESE_10_23.indd 16
15-09-2011 15:24:05
fiber
1032
1097
1038
1039
1048
1046
1047
1170
1123
1114
1134
1117
milano
ďŹ nitura Soft
1137
1100
1120
1101
1121
1107
1127
1171
1140
1106
1126
1177
1149
1116
1136
1168
1146
1104
1124
1112
1132
INGLESE_10_23.indd 17
17
15-09-2011 15:24:14
18
Decors range Parqwall® Silentwall®
legni
INGLESE_10_23.indd 18
388
381
387
Douglas Microline
Douglas Chiaro Microline
Douglas Scuro Microline
382
392
389
391
Douglas Medio Microline
Douglas Microline
Douglas Microline
Douglas Microline
659
660
661
316
Pino Svizzera Microline
Pino Savoia Microline
Pino Chambery Microline
Pommier Morbida
1642
367
1637
324
Pero Italiano Soft
Pero Svizzero Morbida
Pero Marine Soft
Acero Bahia Sei Due
1678
385
1677
364
Acero Due Morbida
Acero Sei Due
Acero Due Morbida
Ontano Chiaro Morbida
365
1618
362
1636
Ontano Medio Morbida
Noce Rosato Sei Due
Noce Torino Morbida
Noce Italiano Morbida
15-09-2011 15:24:22
legni
1329
1328
1365
624
Noce Bossea Morbida
Noce Rigato Morbida
Noce Top Morbida
Noce Roero Sei Due
358
1621
1612
321
Noce Crea Morbida
Teak Maldive Morbida
Teak Sumatra Sei Due
Teak Asia Sei Due
384
383
1355
658
Rovere Toscano Sei Due
Rovere Europa Sei Due
Oak Sei Due
Oak Nature Sei Due
386
1619
1661
1379
Rovere Nazionale Sei Due
Rovere Trasv.le Sei Due
Rovere Montano Morbida
Rovere Sud Morbida
650
653
657
655
Rovere Texas Sei Due
Rovere Dallas Sei Due
Rovere America Sei Due
Rovere Riverwalk Sei Due
656
1372
1321
1322
Rovere Tennessee Sei Due
Continental Oak Morbida
Rovere Stiria Morbida
Rovere Carinzia Morbida
INGLESE_10_23.indd 19
19
15-09-2011 15:24:30
20
Decors range legni
Parqwall® Silentwall®
INGLESE_10_23.indd 20
373
1611
1623
380
Rovere Trentino Morbida
Ciliegio Fey Sei Due
Ciliegio Americ. Soft
Ciliegio Europeo Sei Due
1609
1664
352
1643
Ciliegio Pavese Sei Due
Ciliegio Naturale Morbida
Ciliegio Canino Morbida
Ciliegio Rosa Morbida
370
374
1373
354
Olmo Fine Soft
Castagno Morbida
Mogano Virginia Morbida
Sucupira Morbida
1614
1615
320
1610
Frassino Beige Sei Due
Frassino Rosa Sei Due
Frassino Lidia Sei Due
Cherry Sei Due
1647
1646
1666
1367
Faggio Norvegia Sei Due
Faggio Italia Morbida
Faggio Americ. Sei Due
Faggio Veneto Morbida
323
315
312
314
Oak Scuro Nutshell
Wengè Nutshell
Wengè Nutshell
Wengè Nutshell
15-09-2011 15:24:37
legni
313
1306
1651
1620
Wengè Nutshell
Radica Olmo Morbida
Forest Sei Due
Ebano Sei Due
1317
1304
1628
Morbida
Morbida
Morbida
1309
1324
1354
1352
Morbida
Morbida
Sei Due
Sei Due
1318
1347
1346
1348
1672
1673
1675
1697
1686
1706
Ciliegio Wood
Ontano Wood
Wengè Wood
legni speciali
Nutshell
1342
printwood
INGLESE_10_23.indd 21
21
15-09-2011 15:24:42
22
Decors range printwood
Parqwall® Silentwall®
1688
1699
1689
1696
Betulla Tavolata finitura Sei Due
Aframosia
Faggio Wood
Mutenye Wood
1684
1700
1701
1704
Rovere Wood
Rovere Chiaro
Rovere Decapè
Decapè Chiaro
1705
1693
1698
1690
Decapè Grigio
Tanganica Wood
Noce Chiaro Tavolato Wood
Teak Wood
1685
1683
1649
1702
Acero Wood
Olmo Americano
Zebrano
Zapatero Chiaro
1216
1210
1198
1703 Zapatero Scuro
serigrafia
finitura Sei
INGLESE_10_23.indd 22
15-09-2011 15:24:45
serigrafia
1238
1233
1239
1240
1242
1243
1241
1232
1230
1231
1244
5417
5418
5419
Lucida
Lucida
Soft
5422
5423
5533
5537
Soft
Lucida
digital print
5532
INGLESE_10_23.indd 23
23
15-09-2011 15:24:51
Illustration of profiles Parqwall® Silentwall®
Visible profiles
Special elements
Head or end profile This is used as a starting or end profile on lower, upper and lateral edges.
Rack joint This is used for joining two panels to be fixed vertically and provides the cladding system with supports for shelves and other accessories.
End profile for inside corners Th i s i s u se d f o r t h e re a liz a t io n of i n si de c or ne r s .
Horizontal joint allowing the fixing of shelves and accessories This joint is used as a connecting element between two panels laid horizontally, and allows the walls to be fitted with shelving supports and other furnishing items.
Two-way joint Profile used for joining two panels, both for horizontal and vertical installation.
Click aluminum corner joint with support This is used for joining the butt edges of the panels and especially the covering of pillars.
Fold-away profiles Fold-away profiles Structural profile which can be used as starting or end profile on lower, upper and lateral edges.
Fold-away two-way joint This is used for joining two panels, both for horizontal and vertical installation.
INGLESE_24_32.indd 25
25
15-09-2011 15:38:45
Illustration of profiles Parqwall® Silentwall®
26
Panels fitted vertically
For the optimal installation it is essential that the wall (or the support and ventilation frame) is absolutely plumb. This will guarantee a perfect finishing to the internal corners and external edges of the room.
Two-way joint
1. Base profile (end or fold-away end profile). Prepare the base horizontal profile by cutting it to the required length. Fix the base profile to the wall (or the support frame) allowing a gap of at least 5 mm (3/16 in.) from floor level: this will enable ventilation of the cavity behind. When cladding particularly damp walls, it is necessary to leave a gap of at least 50 mm (1 15/16 in.) from floor level so as to protect the base of the panel from the risk of water being absorbed by the floor. Before tightening the fixing screws, check that the profile is absolutely horizontal. Should it not be, adjust the position by using a spirit level and then tighten the screws. 2. Vertical starting profile (end or fold-away end profile, end profile for inside corners – for corners - click aluminium corner joint with support – for edges). Prepare the vertical profile by cutting it to the required length. Fix the starting end profile to the wall (or the support frame). Before tightening the fixing screws, check that the profile is absolutely vertical. Should it not be, adjust the position and then tighten the screws.
cut at 45°
45°
3. Top capping profile (end or fold-away end profile). Place the horizontal end profile above the end of the panelling. Fix the profile to the wall (or the support frame), and position and tighten the screws only sufficiently to allow them to slide freely in the slotted holes. 4. Panel. Prepare the first Parqwall® panel by cutting it to the required length and then slide it within the two installed guides.
Two-way joint cut at 45°
5. Joint between two panels (two-way joint or rack joint or fold-away joint). Prepare the first Parqwall® panel by cutting it to the required length and then slide it within the two installed guides. Fix the joint to the wall (or the support frame). Then position the next panel to engage the slot on the installed profile.
Head
6. End profile for inside corners. When the Parqwall® forms an inside angle, install the last panel on the wall, trimmed exactly to the size of the remaining wall, insert it in the end profile for inside corners, leaving the surface with the slotted lots visible, then fix it to the wall or to the support frame.
or end profile
Important: when installing Parqwall® with visible aluminum joints, these must be cut at 45°angle, when they come together.
INGLESE_24_32.indd 26
7. Final panel. Position the last panel of each wall by trimming it across its width according to the maximum width allowed by the sliding of the end profile. Position the profile and tighten the screws only sufficiently to allow them to slide freely in the slotted holes. Insert the panel into the guides and then fix it into position by sliding the end profile.
15-09-2011 15:38:47
Illustration of profiles Parqwall® Silentwall®
Panels fitted horizontally
For the optimal installation it is essential that the wall (or the support and ventilation frame) is absolutely plumb. This will guarantee a perfect finishing to the internal corners and external edges of the room.
Two-way joint cut at 45°
45°
Two-way joint cut at 45°
Head or end profile
1. Base profile (end or fold-away end profile). Prepare the base horizontal profile by cutting it to the required length. Fix the profile to the wall (or the support frame) allowing a gap of at least 5 mm (3/16 in.) from floor level: this will enable ventilation of the cavity behind. When cladding particularly damp walls, it is necessary to leave a gap of at least 50 mm (1 15/16 in.) from floor level so as to protect the base of the panel from the risk of water being absorbed by the floor. Before tightening the fixing screws, check that the profile is absolutely horizontal. Should it not be, adjust the position by using a spirit level and then tighten the screws. 2. Vertical starting profile (end or fold-away end profile, end profile for inside corners – for corners - click aluminium corner joint with support – for edges). Prepare the vertical profile by cutting it to the required length. Fix the starting end profile to the wall (or the support frame). Before tightening the fixing screws, check that the profile is absolutely vertical. Should it not be, adjust the position and then tighten the screws. 3. Top capping profile (end or fold-away end profile). Place the end profile above the end of the panelling. Fix the profile to the wall (or the support frame), and position and tighten the screws only sufficiently to allow them to slide freely in the slotted holes. 4. Panel. Prepare the first panel by cutting it to the required length and then slide it within the two installed guides. 5. Joint between two panels (two-way joint or rack joint or fold-away joint). Prepare the joint by cutting it to the required length. Insert the joint in the installed panel slot in such a way that the surface with the slotted holes is visible. Fix the joint to the wall (or the support frame). Then position the next panel to engage the slot on the installed profile. 6. Head joint between two panels (two-way joint or fold-away joint). Prepare the joint by cutting it according to the width of the panel. Insert the joint in the installed panel slot in such a way that the surface with the slotted holes is visible.
Important: when installing Parqwall® with visible aluminum joints, these must be cut at 45°angle, when they come together.
INGLESE_24_32.indd 27
7. End profile for inside corners. When the Parqwall® forms an inside angle, install the last panel on the wall , trimmed exactly to the size of the remaining wall, insert it in the end profile for inside corners, leaving the surface with the slotted lots visible, then fix it to the wall or to the support frame.
27
15-09-2011 15:38:48
Parqwall® Technical features
28
Parqwall® is the material suitable for cladding existing walls, whatever condition they may be in. It is resistant to wear, shock, dampness, fire, acids and light, that is to any surface affecting agents, both internal and external. The Parqwall® cladding system has optimal resistance to fire. Parqwall® is manufactured with materials which are completely resistant to any type of microorganisms and is therefore particularly suitable for cladding in hospitals, nurseries, schools and in all places where hygiene is of paramount importance. Although hard and durable, this material recreates the warmth typical of wood and other natural materials. It is also practical, antistatic and does not attract dust. All these features make it particularly suitable for spaces difficult to maintain, for example bars, restaurants, showrooms, doctors’ surgery rooms and large spaces in general. Anti-vandalism. As already mentioned, Parqwall®’s unique characteristic is its extraordinary resistance to scratches, abrasion, shock, chemicals, ink and spray paints. Parqwall® is coated on both sides with a high pressure HPL laminate.
Anti-stain. Parqwall® is resistant to the most common types of stains (as laid down in the European Standard EN 438) and can be easily cleaned with water and ammonia and, if necessary, with organic solvents.
Resistance to dampness. The special installation technique and the physical and chemical characteristics of its components give the Parqwall® panel surfaces their optimum water repellent qualities and resistance to dampness. Sound proofing/insulating. Parqwall® possesses inherent optimum sound proofing/insulating properties, but in order to obtain best performance it is advisable to insert another insulating material between the panels and the wall: glass fibre, rock wool, etc.
Thermal insulation. Parqwall® is a thermally insulating material. Its comfort characteristics help to retain heat and reduce heating costs.
Thermal transmittance. r=
0,0080 0,16
= 0,05
m2 h °C Cal
- 0,0080= thickness of material in linear meters - 0,16 = thermal conductivity
Reaction to fire. Euroclass: EN1350-1 C-s2, d0 Available on request the Parqwall® FR (Euroclass: EN 1350-1 B-s2, d0) Dimensions. The Parqwall® panels are available in the following sizes: 400/600x2400 mm (15 11/16 or 23 9/16 in x 94 8/16 in.) (WxL) for the Printwood range, 400/600x3000 mm (15 11/16 or 23 9/16 in. x 118 2/16 in.) (WxL) for all other ranges. Panels can be installed either horizontally or vertically. The Parqwall® panels are made of high-pressure plastic laminate (HPL) glued to a high density wood fibre core (HDF = High-Density Fiberboard) of approx. 8 mm (5/16 in.) thickness. Each panel is provided with a longitudinal slot on all 4 sides to allow insertion of various profiles.
Joining. The joint between the panels and the wall is made by means of a simple anodized extruded aluminum profile system. The profiles are provided with slotted holes at ‘500 mm (19 11/16 in.) intervals used to permit each section to be fixed to the wall (or to the supporting and levelling frame behind) by means of screws. The slotted holes make it possible to adjust the level of the panelling and to lock it into position by sliding the end profile, when this is used as a finishing element, both for horizontal and vertical installation.
INGLESE_24_32.indd 28
15-09-2011 15:38:49
SilentwallÂŽ Technical features
SilentwallÂŽ is a noise-reducing development of the modular ParqwallÂŽ system. SilentwallÂŽ is designed to absorb noises from highly-frequented rooms and with a high level of background disturbance.
The values measured show that Silentwall is ideal for absorbing medium to high frequencies, that is for ofďŹ ces, areas of high trafďŹ c, conference rooms and theatres. The above are obtained with the insertion of a 30 mm-thick (1 2/16 in.) polyester sheet insulation between the panel and the wall.
Noise reduction is the ability to dissipate acoustic energy, and is expressed as a coefficient (a) indicated with values between 0 (zero noise-reduction) and 1 (total noise reduction). ‡ Test carried out on SILENTWALLŽ as per UNI EN 20354/93 standard Test frequency
Average values measured (đ?›‚)
Reference scale
100 < HZ > 315 Low frequency
0,28
0 < Îą < 0,3 Low noise-reduction
400 < HZ > 1250 Medium frequency
0,73
0,6 < Îą < 1 High noise-reduction
1600 < HZ > 5000
0,41
Front of panel dimensions in mm
0,3 < Îą < 0,6 Medium noise-reduction
High frequency
Back of panel dimensions in mm 24
4
24
24
Forum haul 5 mm
32
32
8
4
Dimensional Tolerance +/- 0,2 mm
Dimensional Tolerance +/- 0,2 mm
Panel Dimension: 600x3000 mm
Panel Dimension: 600x3000 mm
INGLESE_24_32.indd 29
29
15-09-2011 15:38:49
Commercial data Parqwall® Silentwall®
30
Commercial data Parqwall® Range Colours and texture, Colours, Serie Cresp, Vertical Line, Decori Minimi, Fiber, Serie Milano, Legni, Serie Orientali, Serie Radiche, Serie Aceri, Printwood, Serigrafia 2000 Digital Print
Total thickness
Weight
Standard
Packaging
8,3 ± 0,3 mm (5/16 in.)
Kg/mq 8,2 (1.64 lbs per sq.ft.)
400/600 mm (15 11/16 or 23 9/16 in.) (width) 2400/3000 mm (94 8/16 or 118 2/16 in.) (length)
panels on pallets
Technical specification reference: panels produced from the section of a compound material consisting of an HDF wooden fibre core with an external Print® HPL laminate surface balanced with a Print® HPL laminate. The panels are also milled along the sides creating a groove suitable for the insertion of the aluminium profiles making up the panel support structure to the wall. The profiles are of silver anodized aluminum and enable the installation of the panels both horizontally and vertically. These profiles can be visible or fold-away.
Commercial data Parqwall® FR Range Colours and texture, Colours, Serie Cresp, Vertical Line, Decori Minimi, Fiber, Serie Milano, Legni, Serie Orientali, Serie Radiche, Serie Aceri, Printwood, Serigrafia 2000 Digital Print
Total thickness
Weight
Standard
Packaging
7,9 ± 0,3 mm
Kg/mq 7,7 (1.57 lbs per sq.ft.)
400/600 mm (15 11/16 or 23 9/16 in.) (width) 2400/3000 mm (94 8/16 or 118 2/16 in.) (length)
panels on pallets
Technical specification reference: panels produced from the section of a compound material consisting of an HDF wooden fibre core with an external Print® HPL laminate surface balanced with a Print® HPL laminate. The panels are also milled along the sides creating a groove suitable for the insertion of the aluminium profiles making up the panel support structure to the wall. The profiles are of silver anodized aluminum and enable the installation of the panels both horizontally and vertically. These profiles can be visible or fold-away.
Commercial data Silentwall® Range Colours and texture, Colours, Serie Cresp, Vertical Line, Decori Minimi, Fiber, Serie Milano, Legni, Serie Orientali, Serie Radiche, Serie Aceri, Printwood, Serigrafia 2000 Digital Print
Total thickness
Weight
Standard
Packaging
7,9 ± 0,3 mm
Kg/mq 6,5 (1.33 lbs per sq.ft.)
400/600 mm (15 11/16 or 23 9/16 in.) (width) 2400/3000 mm (94 8/16 or 118 2/16 in.) (length)
panels on pallets
Technical specification reference: panels produced from the section of a compound material consisting of an HDF wooden fibre core with an external Print® HPL laminate surface balanced with a Print® HPL laminate. Noise reduction obtained by milling the panel, parallel to the long side on the back and on the decor( pitch 4/24 mm). This will create a 15% surface perforation with holes radius 6 mm. The panels are also milled along the sides creating a groove suitable for the insertion of the aluminum profiles making up the panel support structure to the wall. The profiles are of silver anodized aluminum and enable the installation of the panels both horizontally and vertically. These profiles can be visible or foldaway.
INGLESE_24_32.indd 30
15-09-2011 15:38:50
Technical data Parqwall® Silentwall®
Ecological E1
Technical data Parqwall® Abrasion resistance
Thickness swelling
Scratch resistance
Impact resistance
Stain resistance
Colour resistance to xenon light
Test method
EN 438-2.6
EN 13329 Annex G
Criteria and/or unit of measure
Revs
%
(N)
(N)
Grade: groups 1 e 2 groups 3 e 4
Grade
Result
IP- revs> 400
8,0
2,5
≥ 22
no alteration
>6
Abrasion resistance
Thickness swelling
Scratch resistance
Impact resistance
Stain resistance
Test method
EN 438-2.6
EN 13329 Annex G
Criteria and/or unit of measure
Revs
%
(N)
(N)
Grade: groups 1 e 2 groups 3 e 4
Grade
Result
IP- revs> 400
8,0
2,5
≥ 22
no alteration
>6
Resistance to cigarette burns
Surface electrical resistance
Reaction to fire
NFPA 99
13501
Grade
ohm Ω
Category (class)
>4 no alteration
The material is antistatic
C-s2, d 0
Resistance to cigarette burns
Surface electrical resistance
Reaction to fire
NFPA 99
13501
Grade
ohm Ω
Category (class)
>4 no alteration
The material is antistatic
B-s2, d 0
Resistance to cigarette burns
Surface electrical resistance
Reaction to fire
NFPA 99
13501
EN 438-2.14 EN 438-2.11 EN 438- 2.15 EN 438-2.16 EN 438-2.18
Ecological E1
Technical data Parqwall® FR
Colour resistance to xenon light
EN 438-2.14 EN 438-2.11 EN 438- 2.15 EN 438-2.16 EN 438-2.18
Ecological E1
Technical data Silentwall® Abrasion resistance
Thickness swelling
Test method
EN 438-2.6
EN 13329 Annex G
Criteria and/or unit of measure
Revs
%
(N)
(N)
Grade: groups 1 e 2 groups 3 e 4
Grade
Grade
ohm Ω
Category (class)
Result
IP- revs> 400
8,0
2,5
≥ 22
no alteration
>6
>4 no alteration
The material is antistatic
B-s2, d 0
INGLESE_24_32.indd 31
Scratch resistance
Impact resistance
Stain resistance
Colour resistance to xenon light
EN 438-2.14 EN 438-2.11 EN 438- 2.15 EN 438-2.16 EN 438-2.18
31
23-09-2011 13:39:08
INGLESE_24_32.indd 24
15-09-2011 15:38:39
PL S.p.A. 22070 VERTEMATE (CO) Strada per Bulgorello, 3 Tel. 031.888.211 Fax 031.901.053 parqcolor@pl-abetgroup.it
p Progetto grafico
Effige (Mi) p Stampatore
La Grafica Rampoldi
Company with quality system as per UNI EN ISO 9001: 2008 cert. n°69
QUARTINO_COP.indd 2
Graphic Design: Effige (MI) Print: arti grafiche maspero fontana & c. spa
PL S.p.A. 22070 VERTEMATE (CO) ITALY Strada per Bulgorello, 3 Tel. +39.031.888.211 Fax +39.031.901.053 sales@pl-abetgroup.it
23-09-2011 13:34:43