Altitude Equipment Rentals by Red Mat Publishing

M85

TECHNICAL SPECIFICATIONS

M85 SIDE VIEW DIAGRAM

• Working Height

87'/26.5 m

• Powered Boom Sections

• Working Side Reach

60'/18.2 m

• Overall Height

• Platform Capacity

750 lbs/340 kg

• Platform Size

30x54 in/76x137 cm

• Platform Type

End-Hung

3 13’/3.9 m

• Unit Weight (Bare)

13,500 lbs/6,123 kg

• Outrigger Spread Main

18’/5.5 m

• Outrigger Spread Auxiliary

12’/3.6 m

• Lifting Capacity (Main Winch) N/A

• Front Gross Axle Weight Rating 10,000 lbs/4,536 kg

• Jib Winch

• Rear Gross Axle Weight Rating 19,000 lbs/8,618 kg

500 lbs/227 kg

Elliott Equipment Company 4427 South 76th Circle Omaha, NE 68127

Phone: 402-592-4500 Fax: 402-592-4553 Email: sales@elliottequip.com

www.elliottequip.com

HIREACH - M85R

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS Maximum Platform Height: 82' ground to platform floor.

piece weldment. Turret rotates on large diameter ball bearing.

Working Range: 87' max. height and 60' max. side reach.

Rotation: Continuous turret rotation with no stops. Hydraulic motor drives turret through dual self-locking gear box.

Work Platform: 30”x54" nonremovable end-mount work platform with 40" high rails. Equipped with two safety lanyard attachment loops and two safety harnesses and 72" lanyards. Platform capacity 750 lbs. Platform Leveling System: Hydraulic system consisting of a single platform cylinder interacting with electroproportional level sensing system. Remote releveling controls provided in platform and at ground controls to give precise leveling capability. Platform Controls: Three individual proportional electronic controllers meter pilot-operated, pressure-compensated modulating valves. Remote controls for boom operations from platform operate from a removable remote control box. Hi/Lo range, start/stop and engine speed toggle controls are also located at platform. Electric remote control cable extends through the electrical slip ring to cable carrier inside of boom to extending boom sections. Lower Controls: Mounted on curbside of turret. Outrigger Controls: Parallel opencenter valve for lever-operated control of right and left outriggers. The outrigger valves are mounted at the rear, under each corner of the bed with roadside valve controlling roadside outriggers and curbside valve controlling curbside outriggers. Outriggers: “A” frame auxiliary outriggers with a 12’ spread, and “MH” out-and-down main outriggers with an 18’ spread. Frame: One piece, all welded, box-type fabrication. Turret: Reverse offset turret is one-

Boom: Steel rectangular tube sections. Assembly includes heavy-duty cylinder fittings, pivot pins, and replaceable wear pads. Boom Extension: Single extension cylinder and cables extend the boom sections proportionally. Lift: One single-acting full displacement, long stroke cylinder, provides smooth and stable boom elevation. Holding valve prevent boom from falling in event of hose failure. Cylinders: All cylinders use microhoned cylinder tubing, chrome shafts, top grade packing and protective rod wipers. Cylinder-mounted holding valves provided on all load-holding cylinders. Hoses: All high pressure hoses are wire braid reinforced with a minimum safety factor of 4 to 1. Oil Tank Capacity: 19 gallon mounted to the truck frame. Hydraulic System: Operating pressure approximately 2,750 PSI. System is parallel open center type and is equipped with liquid-filled pressure gauge. Oil is supplied to upper cylinders through hydraulic union in center of turret to cable carrier inside of the boom. Pump: Gear type, direct mount to truck PTO.

installed in truck cab. Operators Manual & Video: Two CDs and one printed copy of operation, maintenance, safety and parts manual provided with each unit. Operational and safety video provided at delivery. Installation: Unit installed on truck, painted, system and tank filled with oil, tested, inspected, and ready to operate. Standard Paint: Paint boom and turret red, outriggers red, and bed and boxes black. Top of steel bed painted with black nonskid surface. Bumper: Bureau of Motor Carrier Safety rear bumper. Weight: Approximately 13,500 lbs. with 20'6” steel-floor bed less truck. Truck Chassis Required: Approx. 156" C.A., 10,000 lb. front axle and 25,999 lb. GVWR required. Trucks must have increased cooling, heavy-duty front and rear springs, 12V electrical system with high capacity alternator, cab clearance stop/tail/backup lights, and I.D. lamps. Recommended GVWR is minimum for HiReach with flatbed only. Contact factory when additional equipment is to be added. Options: 98” x 36” x 24” Steel Cross Body Box. 500 lb Capacity Platform Material Handling Jib. Air and 110 Volt Lines to Platform. Much More...

PTO: Heavy-duty, high-speed. Cable engaged from cab. Cab Equipment: PTO cable or switch with indicator lights installed in truck cab. Engine speed control and start/ stop installed with control switches in platform remote control box and also located at lower controls. U/L approved 5:BC dry chemical fire extinguisher

Elliott Equipment Company reserves the right to change the specification of any unit at any time without prior notice. This brochure is only a statement of general specifications on the date of this publication. For more detailed info on specific Elliott trucks go to www.elliottequip.com

Elliott Equipment Company 4427 South 76th Circle Omaha, NE 68127

Phone: 402-592-4500 Fax: 402-592-4553 Email: sales@elliottequip.com

www.elliottequip.com

TECHNICAL SPECIFICATIONS

HIREACH - M85 MAXIMUM RANGE AND JIB CAPABILITIES

Elliott Equipment Company 4427 South 76th Circle Omaha, NE 68127

Phone: 402-592-4500 Fax: 402-592-4553 Email: sales@elliottequip.com

www.elliottequip.com

TECHNICAL SPECIFICATIONS

HIREACH - M85 CHASSIS DATA

M85

Wheelbase (WB)

222” / 655 cm

Cab to Axle (CA)

156” / 488 cm

Cab to End of Frame (EOF)

273” / 820 cm

Frame Section Modulus

10.8 in3 / 120,000 psi

Front Axle Gross Weight Rating

10,000 lb / 4,536 kg

Rear Axle Gross Weight Rating

19,000 lb / 8,618 kg

Extended Front Frame

N/A

Chassis data is minimum general requirements-not for engineering. Actual dimensions and truck data will depend on truck selection and axle configuration.

OPTIONS Non-CDL Chassis Options Take advantage of the low chassis GVWR requirements by mounting your HiReach on a non-CDL truck chassis.

Bed Accessories Mount a wide variety of accessories including generators and inverters.

Material Handling Jib Equip your HiReach platform with a hydraulic material handling jib crane to handle up to 500 lbs.

Platform Accessories Choose from a list of platform accessories including 110V outlets, 3/8” air lines, sign forks, and much more.

High Capacity Platform Take advantage of the 750 lb capacity work platform by carrying additional tools and supplies onto the job site.

Walkway Platform Access Select Elliott’s walkway access to the platform to easily step into the platform from the bed with the boom stowed.

Outrigger Pad Holders Outrigger pad holders safely store your outrigger pads for travel and leave plenty of room for tool boxes.

Line Body Let us work with you to customize a line body to secure your tools and supplies the the best way for your application.

Elliott Equipment Company 4427 South 76th Circle Omaha, NE 68127

Phone: 402-592-4500 Fax: 402-592-4553 Email: sales@elliottequip.com

www.elliottequip.com

TRAILER-MOUNTED Z-BOOMS

TZ -50 TM

Specifications MODEL MEASUREMENTS Working height* Platform height Entry height Horizontal reach Clear outreach Up and over clearance A Platform length B Platform width C Height - stowed D Length - stowed E Width - stowed F Ground clearance - center G Length - outrigger footprint H Width - outrigger footprint

TZTM-50 US

Metric

55 ft 6 in 49 ft 6 in 1 ft 8 in 29 ft 2 in 23 ft 1 in 22 ft 2 ft 2.8 in 3 ft 8 in 6 ft 10 in 23 ft 6 in 5 ft 6 in 10 in 14 ft 4 in 14 ft 4 in

17.09 m 15.09 m .51 m 8.89 m 7.04 m 6.71 m .68 m 1.12 m 2 m 7.16 m 1.68 m .25 m 4.37 m 4.37 m

D B

F E H

RANGE OF MOTION TZTM-50

PRODUCTIVITY Lift capacity (ANSI, CSA) - standard Lift capacity (ANSI, CSA) - rotating platform Lift capacity (CE/AUS) - standard Lift capacity (CE/AUS ) - rotating platform Jib boom Jib working range Self leveling platform Platform rotation option AC power to platform Turntable rotation Outrigger leveling capability Drive speed Gradeability** Towing speed rate Tongue weight - ANSI, CSA Tongue weight - CE Surge and parking brakes Controls Tires - ANSI, CSA Tires - CE Coupler

500 lbs 227 kg 500 lbs 227 kg 440 lbs 200 kg 440 lbs 200 kg 4 ft 1 in 1.25 m 135° 2.5° standard 160° hydraulic standard 359° non-continuous 10° 0.85 mph 1.37 km/h 20% 60 mph 97 km/h 400 lbs 181 kg 220 lbs 100 kg standard variable speed system ST 225/75 R15 215 R14C 2 in ( 5.08 cm) hitch coupler standard

55 ft

16.76 m

50 ft

15.24 m

45 ft

13.72 m

40 ft

12.19 m

35 ft

10.67 m

30 ft

9.14 m

25 ft

7.62 m

20 ft 6.1 m

15 ft

4.57 m

10 ft

3.05 m

5 ft

1.52 m

0 ft 0m

-30 ft -25 ft -20 ft -15 ft -10 ft -5 ft

-9.14 m -7.62 m -6.1 m -4.57 m -3.05 m -1.52 m

0 ft 0m

5 ft

10 ft 15 ft 20 ft 25 ft 30 ft

1.52 m 3.05 m 4.57 m 6.1 m 7.62 m 9.14 m

POWER Power source - standard 24V DC (four 6V 225 Ah batteries) Power source - drive option 24V DC (four 6V 244 Ah batteries) Power source - option Hybrid DC/Gas Honda 5.5 hp (4.1 kW) Fuel tank capacity .95 gal 3.6 L Hydraulic tank capacity 4.75 gal 18 L Hydraulic system capacity 8.0 gal 30 L

WEIGHT*** ANSI, CSA, Australia CE

4,400 lbs 4,464 lbs

1,996 kg 2,025 kg

Standards Compliance ANSI A92.2, CSA C225, EN 280, AS 1418.10

www.genieindustries.com

*T he metric equivalent of working height adds 2 m to platform height. U.S. adds 6 ft to platform height. ** Gradeability applies to driving on slopes. See operator’s manual for details regarding slope ratings. *** Weight will vary depending on options and/or country standards.

TRAILER-MOUNTED Z-BOOMS

TZ -50 TM

Features EASILY CONFIGURED TO MEET YOUR NEEDS PLATFORM OPTIONS

STANDARD FEATURES MEASUREMENTS

•A luminum 26.8 x 44 in (.68 x 1.12 m) • 160° hydraulic platform rotation

• 55 ft 6 in (17.09 m) working height • 29 ft 2 in (8.89 m) horizontal reach • Up to 500 lb (227 kg) lift capacity

POWER OPTIONS

PRODUCTIVITY

• 24V DC power source • Hybrid Honda 5.5 Hp (4.1 Kw) 45 amp charging system

• • • • • • • • • • • •

DRIVE • Drive and set option (ANSI, CSA, AUS) • Drive only (CE) COUPLER OPTIONS Combination hitch • 2 in (5.08 cm) ball coupler • 2.31 in (5.87 cm) ball coupler • 2.5 in (6.53 cm) I.D. pintle ring coupler • Clevis coupler TIRE OPTIONS • ST 225/75 R15 tires (ANSI, CSA) • 215 R14C tires (CE)

• • • • • •

Industry leading working envelope xtension boom E Self-leveling platform 4 ft jib with 135° working range AC wiring to platform Hydraulic outriggers Automatic 10° leveling system Outrigger interlocks Mechanical parking brake Hydraulic surge brakes Auxiliary pump down Combination hitch with coupler lever lock Dual jockey wheels 359° non-continuous turntable rotation Easy to access batteries Hour meter Tilt alarm / sensor Illuminated outrigger indicators

POWER •2 4V DC power source (four 6V 225 Ah batteries)

OPTIONS & ACCESSORIES PRODUCTIVITY •1 60° hydraulic platform rotation • Drive and set option with larger 244 Ah batteries pack • 2 in (5.08 cm) ball coupler • 2.31 in (5.87 cm) ball coupler • 2.5 in (6.35 cm) I.D. pintle ring coupler • Combination hitch • Clevis coupler • Wheel chocks • Fluorescent tube caddy • Full size spare tire • Operational warning beacon package • Non-marking outrigger footpads • Battery charge indicator (BCI) • Tool tray • Bicycle guard (CE only) POWER •H ybrid Honda 5.5 Hp (4.1 Kw) 45 amp charging system option

Genie United States

Genie Europe

18340 NE 76th Street P.O. Box 97030 Redmond, Washington 98073-9730

The Maltings Wharf Road Grantham NG31 6BH UK

Telephone +1 (425) 881-1800 Toll Free in USA/Canada +1 (800)-536-1800 Fax +1 (425) 883-3475

Distributed By:

Telephone +44 (0)1476 584333 Fax +44 (0)1476 584334 Email: AWP-InfoEurope@terex.com

Effective Date: January, 2010. Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and we make no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation, Genie Industries, Inc. and/or their subsidiaries in the U.S.A. and many other countries and all rights are reserved. Terex® is a Registered Trademark of Terex Corporation in the U.S.A. and many other countries. Genie® is a Registered Trademark of Genie Industries, Inc. in the U.S.A. and many other countries. Genie is a Terex Company. © 2010 Terex Corporation. TZ50 0210K. Part No. 109373

www.genieindustries.com

SELF-PROPELLED TELESCOPIC BOOMS

S -60 X & S -65 TM

Specifications A

A B

RANGE OF MOTION STM-60 X B

D C

C G

G F

MODELS MEASUREMENTS Working height maximum* Platform height maximum Horizontal reach maximum Below ground reach A Platform length - 8 ft model Platform length - 6 ft model B Platform width - 8 ft model Platform width - 6 ft model C Height - stowed Height - stowed Trax D Length - stowed Length - transport (jib tucked under) E Width (with standard tires) Width - Trax F Wheelbase G Ground clearance - center

S -60 X

STM-65

Metric

66 ft 60 ft 50 ft 10 in 5 ft 7 in 3 ft 2 ft 6 in 8 ft 6 ft 8 ft 11 in 9 ft 1 in 27 ft 11 in ——— 8 ft 2 in 8 ft 6 in 8 ft 2.5 in 1 ft 2.5 in

20.30 m 18.30 m 15.48 m 1.70 m .91 m .76 m 2.44 m 1.83 m 2.72 m 2.77 m 8.51 m ——— 2.49 m 2.59 m 2.50 m .37 m

71 ft 65 ft 56 ft 2 in 8 ft 11 in 3 ft 2 ft 6 in 8 ft 6 ft 8 ft 11 in 9 ft 1 in 31 ft 2 in 25 ft 8 ft 2 in 8 ft 6 in 8 ft 2.5 in 1 ft 2.5 in

21.80 m 19.80 m 17.10 m 2.72 m .91 m .76 m 2.44 m 1.83 m 2.72 m 2.77 m 9.50 m 7.60 m 2.49 m 2.59 m 2.50 m .37 m

70 ft

21.34 m

60 ft

18.29 m

50 ft

PRODUCTIVITY Lift capacity Platform rotation Vertical jib rotation Turntable rotation Turntable tailswing Drive speed - 2WD stowed Drive speed - 4WD stowed Drive speed - Trax stowed Drive speed - raised or extended Gradeability - 2WD - stowed** Gradeability - 4WD - stowed** Turning radius - inside Turning radius - outside Controls Tires - RT Lug

RANGE OF MOTION STM-65

15.24 m

500 lbs/1000 lbs 227 kg/454 kg 160° —— 360° continuous 4 ft 1.22 m 4.0 mph 6.4 km/h 3.0 mph 4.8 km/h 2.3 mph 3.7 km/h 0.68 mph 1.1 km/h 30% 45% 7 ft 9 in 2.36 m 18 ft 2 in 5.54 m 12 V DC proportional 355/55D 625

500 lbs 227 kg 160° 135° 360° continuous 4 ft 1.22 m 4.0 mph 6.4 km/h 3.0 mph 4.8 km/h 2.3 mph 3.7 km/h 0.68 mph 1.1 km/h 30% 45% 7 ft 9 in 2.36 m 18 ft 9 in 5.72 m 12 V DC proportional 355/55D 625

40 ft

12.19 m

30 ft

9.14 m

20 ft

6.1 m

10 ft

3.05 m

0 ft 0m

-10 ft

-3.05 m

-10 ft

-3.05m

0 ft 0m

10 ft

3.05 m

20 ft

6.10 m

30 ft

9.14 m

40 ft

12.2 m

50 ft

15.24 m

60 ft

18.29 m

POWER Power source

Auxiliary power unit Hydraulic tank capacity Fuel tank capacity

Ford DSG-423 4 cylinder gas/LPG 75 hp (56 kW) Deutz D2011L03i 3 cylinder diesel 46 hp (34.3 kW) Perkins 404D-22 4 cylinder diesel 51 hp (38 kW) Deutz D2011L04i 4 cylinder turbo charged diesel 74 hp (55 kW) 12 V DC 12 V DC 45 gal 170 L 45 gal 170 L 35 gal 132 L 35 gal 132 L

WEIGHT*** 2WD 4WD Trax

STANDARDS COMPLIANCE www.genieindustries.com

20,570 lbs 20,740 lbs 25,430 lbs

9,330 kg 9,408 kg 11,535 kg

22,100 lbs**** 22,270 lbs**** 26,960 lbs

ANSI A92.5, CSA B354.4, EN 280, AS 1418.10

10,024 kg 10,102 kg 12,229 kg

* The metric equivalent of working height adds 2 m to platform height. U.S. adds 6 ft to platform height. ** Gradeability applies to driving on slopes, see operator’s manual for details regarding slope ratings. *** Weight will vary depending on options and/or country standards. **** S60Xc weight same as S65

SELF-PROPELLED TELESCOPIC BOOMS

S -60 X & S -65 TM

Features EASILY CONFIGURED TO MEET YOUR NEEDS PLATFORM OPTIONS • Steel 8 ft (2.44 m) (standard) • Steel 6 ft (1.83 m) • 8 ft (2.44 m) tri-entry JIB OPTIONS • Non-jib • 5 ft (1.52 m) jib boom ENGINE OPTIONS • • • •

Ford gas/LPG 75 hp (56 kW) Deutz diesel 46 hp (34.3 kW) Perkins diesel 51 hp (38 kW) Deutz turbo diesel 74 hp (55 kW)

DRIVE OPTIONS • 2WD • 4WD AXLE OPTIONS • Active oscillation • Non-oscillating TIRE OPTIONS • Rough terrain air-filled (standard) • Rough terrain foam-filled • Rough terrain non-marking (air or foam-filled) • High flotation air-filled • Sealant treated air-filled • Track system QTS-R42 Loegering

* Available on select models * * Available only with Ford engine

STANDARD FEATURES MEASUREMENTS S™-60 X* • 66 ft (20.30 m) working height • 50 ft 10 in (15.48 m) horizontal reach • 500 lb (227 kg) unrestricted and 1000 lb (454 kg) restricted lift capacity S™-60 XC* • 66 ft (20.30 m) working height • 50 ft 10 in (15.48 m) horizontal reach • 750 lb (340 kg) unrestricted and 1250 lb (680 kg) restricted lifting capacity S™-65 • 71 ft (21.80 m) working height • 56 ft 2 in (17.10 m) horizontal reach • 500 lb (227 kg) lift capacity PRODUCTIVITY • Self-leveling platform • Hydraulic platform rotation • Fully proportional Hall effect joystick controls • Fuel select switch on platform and ground control panels (Gas/LPG models) • Drive enable • AC power cord to platform • Tilt alarm • Descent alarm • Hour meter • Horn • 360° continuous turntable rotation • Positive traction drive • Two speed wheel motors POWER • 12 V DC auxiliary power • Anti-restart engine protection • Auto engine fault shutdown • Swing out engine tray • Deutz intake air heater

Genie United States

Genie Europe

18340 NE 76th Street P.O. Box 97030 Redmond, Washington 98073-9730

The Maltings Wharf Road Grantham NG31 6BH UK

Telephone +1 (425) 881-1800 Toll Free in USA/Canada +1 (800) 536-1800 Fax +1 (425) 883-3475

OPTIONS & ACCESSORIES PRODUCTIVITY OPTIONS • Platform swing gate • Half-mesh platform inserts with swing gate • Platform top auxiliary rail • Arc Pro 275™ Heavy-Duty Welder package • Welder Ready package • Weld leads to platform • Air line to platform • Hydraulic oil cooler • Biodegradable hydraulic oil • Hostile environment kit • Deluxe hostile environment kit • Aircraft protection package (6 ft platform) • Thumb rocker steer • Tool tray • Alarm package • Panel cradle package* • Platform work lights • Lockable platform control box covers • Second battery • Tow package • FM safety approval** • Light package POWER OPTIONS • Engine gauge package • AC generator packages (110V/-220V/50Hz, 3000W) • Cold Weather Packages • Diesel scrubber/spark arrestor muffler (catalytic muffler) • LPG tank 33.5 lb (15.19 kg) capacity • Intake air pre-cleaner

Distributed By:

Telephone +44 (0)1476 584333 Fax +44 (0)1476 584334 Email: AWP-InfoEurope@terex.com

Effective Date: April, 2011. Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and we make no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation, Genie Industries, Inc. and/or their subsidiaries in the U.S.A. and many other countries and all rights are reserved. Terex is a Registered Trademark of Terex Corporation in the U.S.A. and many other countries. Genie is a Registered Trademark of Genie Industries, Inc. in the U.S.A. and many other countries. Genie is a Terex Brand. © 2011 Terex Corporation. S60 0210A. Part No. 127275

www.genieindustries.com

SELF-PROPELLED ARTICULATING BOOMS

Z -80/60 TM

Specifications

MODEL MEASUREMENTS Working height maximum* Platform height maximum Horizontal reach maximum Up and over clearance maximum Below ground reach A Platform length - 8 ft / 6 ft B Platform width - 8 ft / 6 ft C Height - stowed D Length - stowed E Length - transport F Width G Wheelbase H Ground clearance - center

Z -80/60 TM

US 84 ft 78 ft 60 ft 29 ft 15 ft 10 in 3ft/2ft 6in 8ft/6ft 9 ft 10 in 37 ft 37 ft 8 ft 2 in 9 ft 4 in 12 in

Metric 25.77 m 23.77 m 18.29 m 8.83 m 4.83 m .91m/.76m 2.44m/1.83m 3.00 m 11.27 m 11.27 m 2.49 m 2.85 m .30 m

RANGE OF MOTION ZTM-80/60 90 ft 27.43 m

80 ft 24.38 m

70 ft 21.34 m

60 ft 18.29 m

50 ft 15.24 m

40 ft 12.19 m

30 ft 9.14 m

20 ft

PRODUCTIVITY Lift capacity Platform rotation Vertical jib rotation Turntable rotation Turntable tailswing - riser up Turntable tailswing - riser down Drive speed - stowed Drive speed - raised** Lift speed to full height Gradeability - 2WD - stowed*** Gradeability - 4WD - stowed*** Turning radius - 2WS inside Turning radius - 2WS outside Turning radius - 4WS inside Turning radius - 4WS outside Controls Tires

6.1 m

500 lbs 160° 135° 360° continuous 3 ft 10 in 7 ft 4 in 3.0 mph 0.68 mph 76 sec 30% 45% 14 ft 6 in 24 ft 6 in 7 ft 15 ft 12 V DC proportional 18-625 NHS

227 kg

10 ft 3.05 m

0 ft 0m

1.17 m 2.24 m 4.83 km/h 1.1 km/h

-10 ft -3.05 m

-20 ft -6.1 m

-10 ft

0 ft

10 ft

20 ft

30 ft

40 ft

50 ft

60 ft

-3.05 m

3.05 m

6.1 m

9.14 m

12.19 m

15.24 m

18.29 m

4.42 m 7.47 m 2.13 m 4.57 m

POWER Power source

Deutz TD 2011 L04i 4 cylinder diesel 74 hp (55 kW) Perkins 804D-33 4 cylinder diesel 63 hp (47 kW) Continental TME27 4 cylinder gas/LPG 74 hp (55 kW) Auxiliary power unit 12 V DC Hydraulic tank capacity 45 gal 170 L Fuel tank capacity – diesel machines 35 gal 132 L Fuel tank capacity – gas/LPG machines 30 gal 114 L

WEIGHT**** 2WS 4WS

STANDARDS COMPLIANCE www.genieindustries.com

35,900 lbs 37,500 lbs

16,284 kg 17,010 kg

«ANSI A92.5, CSA B354.4, EN 280, AS 1418.10

* The metric equivalent of working height adds 2 m to platform height. U.S. adds 6 ft to platform height. ** In lift mode (platform raised), the machine is designed to operate on firm, level surfaces only. *** Gradeability applies to driving on slopes. See operator’s manual for details regarding slope ratings. **** Weight will vary depending on options and/or country standards.

SELF-PROPELLED ARTICULATING BOOMS

Z -80/60 TM

Features EASILY CONFIGURED TO MEET YOUR NEEDS PLATFORM OPTIONS • Steel 8 ft (2.44 m) (standard) • Steel 6 ft (1.83 m) • 8 ft (2.44 m) tri-entry JIB • 6 ft (1.83 m) jib boom ENGINE OPTIONS • Deutz diesel 74 hp (55 kW) • Perkins diesel 63 hp (47 kW) • Continental gas/LPG 74 hp (55 kW) DRIVE/STEER OPTIONS • 4WD (standard) • 2WS (standard) • 4WS AXLE • Active oscillation TIRE OPTIONS • Rough terrain foam-filled (standard) • Rough terrain non-marking foam-filled • High flotation rough terrain

STANDARD FEATURES MEASUREMENTS: • • • •

84 ft (25.77 m) working height 60 ft (18.28 m) horizontal reach 29 ft (8.83 m) up and over clearance Up to 500 lb (227 kg) lift capacity

PRODUCTIVITY • • • • • • • • • • • • • • • • • •

6 ft (1.83 m) jib with 135° range Self-leveling platform Hydraulic platform rotation Fully proportional Hall effect controls On-board diagnostics ALC 1000 electronic control system Hydraulic oil cooler Drive enable AC power cord to platform Horn Hour meter Tilt alarm Descent alarm 360° continuous turntable rotation Locking turntable covers Full-time positive traction drive Two speed wheel motors Four steering modes: front, rear, crab and coordinated • Configurable controls to limit lift height to 70 ft POWER • • • • • • •

12 V DC auxiliary power Anti-restart engine protection Auto engine fault shutdown Engine monitoring display Block heater (Continental engine) Dual battery Engine status display

OPTIONS & ACCESSORIES PRODUCTIVITY OPTIONS • Platform swing gate • Half-mesh platform inserts with swing gate • Platform top auxiliary rail • Arc Pro 275™ Heavy-Duty Welder package • Welder Ready package • Weld leads to platform • Air line to platform • Biodegradable hydraulic oil • Hostile environment package • Deluxe hostile environment package • Thumb rocker steer • Aircraft protection package (6 ft platform only) • Tool tray • Pipe cradles (pair) • Alarm package • Panel cradle package* • Platform work lights • Lockable platform control box covers • Light package POWER OPTIONS • AC generator packages (110V/60Hz 220V/50Hz, 3000W) • Cold Weather Packages • Diesel scrubber/spark arrestor (catalytic muffler) • LPG tank only, steel, 33.5 lb (15.19 kg) capacity

* Available on select models

Genie United States

Genie Europe

18340 NE 76th Street P.O. Box 97030 Redmond, Washington 98073-9730

The Maltings Wharf Road Grantham NG31 6BH UK

Telephone +1 (425) 881-1800 Toll Free in USA/Canada +1 (800) 536-1800 Fax +1 (425) 883-3475

Distributed By:

Telephone +44 (0)1476 584333 Fax +44 (0)1476 584334 Email: AWP-InfoEurope@terex.com

www.genieindustries.com

SELF-PROPELLED TELESCOPIC BOOMS

S -80 X & S -85 TM

Specifications A

A B

RANGE OF MOTION STM-80 X B

G F

MODELS MEASUREMENTS Working height maximum* Platform height maximum Horizontal reach maximum Below ground reach A Platform length - 8 ft model Platform length - 6 ft model B Platform width - 8 ft model Platform width - 6 ft model C Height - stowed D Length - stowed Length - transport (jib tucked under) E Width F Wheelbase G Ground clearance - center

STM-80 X

STM-85

Metric

86 ft 80 ft 71 ft 6 in 6 ft 1 in 3 ft 2 ft 6 in 8 ft 6 ft 9 ft 2 in 36 ft 6 in ——— 8 ft 2 in 9 ft 4 in 13 in

26.20 m 24.40 m 21.80 m 1.85 m .91 m .76 m 2.44 m 1.83 m 2.80 m 11.10 m ——— 2.50 m 2.80 m .33 m

91 ft 85 ft 76 ft 6 in 9 ft 6 in 3 ft 2 ft 6 in 8 ft 6 ft 9 ft 2 in 40 ft 38 ft 8 ft 2 in 9 ft 4 in 13 in

27.70 m 25.90 m 23.30 m 2.89 m .91 m .76 m 2.44 m 1.83 m 2.80 m 12.20 m 11.60 m 2.50 m 2.80 m .33 m

RANGE OF MOTION STM-85

PRODUCTIVITY Lift capacity Platform rotation Vertical jib rotation Turntable rotation Turntable tailswing Drive speed - stowed - 2WD/4WD Drive speed - raised/extended Gradeability - 2WD - stowed** Gradeability - 4WD - stowed** Turning radius - axle extended: inside outside Controls Tires - RT lug

500 lb/ 1000 lb 227 kg/ 454 kg 160° —— 360° continuous 4 ft 8 in 1.42 m 3.5 mph 5.6 km/h 0.68 mph 1.1 km/h 30% 45% 12 ft 3.70 m 21 ft 6 in 6.60 m 12V DC proportional Foam filled 18-625, 16 ply

500 lbs 227 kg 160° 135° 360° continuous 4 ft 8 in 1.42 m 3.5 mph 5.6 km/h 0.68 mph 1.1 km/h 30% 45% 12 ft 3.70 m 21 ft 6 in 6.60 m 12V DC proportional Foam filled 18-625, 16 ply

POWER Power source

Auxiliary power unit Hydraulic tank capacity Fuel tank capacity - diesel Fuel tank capacity - gas/LPG

Deutz TD2011 L04i 4 cylinder turbo diesel 74 hp (55 kW) Perkins 804D-33 4 cylinder diesel 63 hp (47 kW) Continental TME27 4 cylinder Gasoline/LPG 74 hp (55 kW) 12V DC 12V DC 40 gal 150 L 40 gal 150 L 35 gal 132 L 35 gal 132 L 30 gal 113.6 L 30 gal 113.6 L

WEIGHT*** 2WD 4WD

STANDARDS COMPLIANCE

www.genieindustries.com

35,460 lbs 35,560 lbs

16,084 kg 16,130 kg

ANSI A92.5, CSA B354.4,EN 280

37,900 lbs 38,000 lbs

17,191 kg 17,236 kg * The metric equivalent of working height adds 2 m to platform height. U.S. adds 6 ft to platform height. ** Gradeability applies to driving on slopes. See operator’s manual for details regarding slope ratings. *** Weight will vary depending on options and/or country standards.

SELF-PROPELLED TELESCOPIC BOOMS

S -80 X & S -85 TM

Features STANDARD FEATURES

EASILY CONFIGURED TO MEET YOUR NEEDS

MEASUREMENTS PLATFORM OPTIONS • Steel 8 ft (2.44 m) • Steel 6 ft (1.83 m) • 8 ft (2.44 m) tri-entry JIB OPTIONS • Non-jib • 5 ft (1.52 m) jib boom ENGINE OPTIONS

S™-80 X* • 86 ft (26.38 m) working height • 71 ft 6 in (21.8 m) horizontal reach • 500 lbs (227 kg) unrestricted and 1000 lbs (454 kg) restricted lift capacity ™

S -85 • 91 ft (27.90 m) working height • 76 ft 6 in (23.3 m) horizontal reach • 500 lb (227 kg) lift capacity

• Deutz turbocharged diesel 74 hp (55 kW) PRODUCTIVITY • Perkins diesel 63 hp (47 kW) • Self-leveling platform • Continental Gas/LPG 74 hp (55 kW) • Hydraulic platform rotation DRIVE OPTIONS • Fully proportional Hall effect • 2WD joystick controls • 4WD • Drive enable • AC power cord to platform AXLE • Horn • Fixed width with active oscillation • Hour meter • Tilt alarm TIRE OPTIONS • Descent alarm • Rough terrain foam-filled (standard) • 360° continuous turntable rotation • Rough terrain non-marking foam-filled • Positive traction drive • High floatation air-filled • Two speed wheel motors (Increases width by 4 in) POWER

OPTIONS & ACCESSORIES PRODUCTIVITY OPTIONS • Platform swing gate • Half mesh platform inserts with swing gate • Platform top auxiliary rail • Arc Pro 275™ Heavy-Duty Welder package • Welder Ready package • Weld leads to platform • Air line to platform • Hydraulic oil cooler • Biodegradable hydraulic oil • Hostile environment kit • Deluxe hostile environment kit • Aircraft protection package (6 ft platform only) • Tool tray • Alarm package • Panel cradle package* • Platform work lights • Lockable platform control box covers • Tow package • Light package

• • • •

12V DC auxiliary power Anti-restart engine protection Auto engine fault shutdown Catalytic converter muffler (Continental engine only) • Engine block heater (Continental engine only)

POWER OPTIONS

Genie United States

Genie Europe

Distributed By:

18340 NE 76th Street P.O. Box 97030 Redmond, Washington 98073-9730

The Maltings Wharf Road Grantham NG31 6BH UK

• Engine gauge package • AC generator packages (110V/-220V/50Hz, 3000W)* • Cold Weather Packages • Diesel scrubber/spark arrestor muffler (catalytic muffler) • LPG tank only, steel, 33.5 lb (15.19 kg) capacity • Intake air pre-cleaner

* Available on select models ** Not available on CE machines

Telephone +1 (425) 881-1800 Toll Free in USA/Canada +1 (800) 536-1800 Fax +1 (425) 883-3475

Telephone +44 (0)1476 584333 Fax +44 (0)1476 584334 Email: AWP-InfoEurope@terex.com

www.genieindustries.com

SELF-PROPELLED TELESCOPIC BOOMS

S -100 & S -105 TM

Specifications A

A B

RANGE OF MOTION STM-100 B

110 ft

33.53 m

100 ft

30.48 m

90 ft

27.43 m

80 ft

24.38 m

MODELS MEASUREMENTS Working height maximum* Platform height maximum Horizontal reach maximum Below ground reach A Platform length - 8 ft model Platform length - 6 ft model B Platform width - 8 ft model Platform width - 6 ft model C Height - stowed D Length - stowed Length - transport (jib tucked under) E Width - axle retracted Width - axle extended F Wheelbase G Ground clearance - center

70 ft

S -100

21.34 m

STM-105

Metric

106 ft 100 ft 75 ft 6 ft 6 in 3 ft 2 ft 6 in 8 ft 6 ft 10 ft 1 in 42 ft 8 in ——— 8 ft 2 in 11 ft 12 ft 1 ft 5.5 in

32.48 m 30.48 m 22.86 m 1.98 m .91 m .76 m 2.44 m 1.83 m 3.07 m 13.00 m ——— 2.49 m 3.35 m 3.66 m .44 m

111 ft 105 ft 80 ft 10 ft 3 ft 2 ft 6 in 8 ft 6 ft 10 ft 1 in 46 ft 39 ft 11 in 8 ft 2 in 11 ft 12 ft 1 ft 5.5 in

34.00 m 32.00 m 24.38 m 3.05 m .91 m .76 m 2.44 m 1.83 m 3.07 m 14.02 m 12.17 m 2.49 m 3.35 m 3.66 m .44 m

Auxiliary Power Unit Hydraulic Tank Capacity Fuel Tank Capacity

0.68 mph

340 kg

20 ft

6.1 m

10 ft

3.05 m

0 ft 0m

-10 ft

-3.05 m

-20 ft

-6.1 m

-10 ft

0 ft

10 ft

20 ft

30 ft

-3.05 m

3.05 m

6.1 m

9.14 m 12.19 m 15.24 m 18.29 m 21.34 m

40 ft

50 ft

60 ft

70 ft

80 ft 24.38

227 kg

33.53 m

1.68 m 1.22 m 4.8 km/h

1.1 km/h

0.68 mph

1.1 km/h

18.29 m

0.34 mph .55 km/h 40% 13 ft 7 in 4.14 m 21 ft 7 in 6.58 m 9 ft 2.74 m 19 ft 10 in 6.05 m 12 V DC proportional 385/65D 22.5 385/65D 24

15.24 m

100 ft

30.48 m

90 ft

27.43 m

80 ft

24.38 m

70 ft

21.34 m

60 ft 50 ft

0.34 mph .55 km/h 40% 13 ft 7 in 4.14 m 21 ft 7 in 6.58 m 9 ft 2.74 m 19 ft 10 in 6.05 m 12 V DC proportional 385/65D 22.5 385/65D 24

40 ft

12.19 m

30 ft

9.14 m

20 ft

6.1 m

10 ft

3.05 m

0 ft 0m

-10 ft

Deutz TD 2011 L04i 4-cylinder turbo diesel, 74 hp (55 kW) Perkins 804-33T 4-cylinder turbo diesel, 83 hp (62 kW) 12 V DC 12 V DC 55 gal 208 L 55 gal 208 L 40 gal 151 L 40 gal 151 L 39,700 lbs

www.genieindustries.com

30 ft

9.14 m

500 lbs 160° 135° 360° continuous 5 ft 6 in 4 ft 3.0 mph

WEIGHT*** STANDARDS COMPLIANCE

40 ft

12.19 m

110 ft

750 lbs 160° —— 360° continuous 5 ft 6 in 4 ft 3.0 mph

POWER Power Source

50 ft

15.24 m

RANGE OF MOTION STM-105

PRODUCTIVITY Lift capacity Platform rotation Vertical jib rotation Turntable rotation Turntable tailswing - axle retracted Turntable tailswing - axle extended Drive speed - stowed Drive speed - raised or extended below 80 ft Drive speed - raised or extended above 80 ft Gradeability - stowed** Turning radius - axles retracted: inside outside Turning radius - axles extended: inside outside Controls Tires - RT lug RT solid

60 ft

18.29 m

18,008 kg

40,000 lbs

ANSI A92.5, CSA B354.4, EN 280, AS 1418.10

18,144 kg

-3.05 m

-20 ft

-6.1 m

-10 ft

0 ft

10 ft

20 ft

30 ft

-3.05 m

3.05 m

6.1 m

9.14 m 12.19 m 15.24 m 18.29 m 21.34 m

40 ft

50 ft

60 ft

70 ft

80 ft 24.38

* The metric equivalent of working height adds 2 m to platform height. U.S. adds 6 ft to platform height. ** Gradeability applies to driving on slopes. See operator’s manual for details regarding slope ratings. *** Weight will vary depending on options and/or country standards.

SELF-PROPELLED TELESCOPIC BOOMS

S -100 & S -105 TM

Features EASILY CONFIGURED TO MEET YOUR NEEDS

STANDARD FEATURES MEASUREMENTS

PLATFORM OPTIONS • Steel 8 ft (2.44 m) (standard) • Steel 6 ft (1.83 m) • 8 ft (2.44 m) tri-entry JIB OPTIONS • Non-jib • 5 ft (1.52 m) jib boom

S™-100 • 106 ft (32.48 m) working height • 75 ft (22.86 m) horizontal reach • 750 lb (340 kg) lift capacity S™-105 • 111 ft (34.00 m) working height • 80 ft (24.38 m) horizontal reach • 500 lb (227 kg) lift capacity

ENGINE OPTIONS • Deutz diesel 74 hp (55 kW) • Perkins diesel 83 hp (62 kW) DRIVE/STEER • 4WD (standard) • 4WS (standard) AXLE • Extendable axles (standard) TIRE • Rough terrain foam-filled (standard) • Rough terrain solid

PRODUCTIVITY • Self-leveling platform • Hydraulic platform rotation • Fully proportional Hall effect joystick controls • Hydraulic oil cooler • Drive enable • AC power cord to platform • Horn • Hour meter • Tilt alarm • Descent alarm • Alarm package • 360° continuous turntable rotation • Locking low profile turntable covers • Positive traction drive • Two speed wheel motors • Configurable controls to limit lift height to 80 ft • Ground control box cover • Engine status display

OPTIONS & ACCESSORIES PRODUCTIVITY OPTIONS • Platform swing gate • Half mesh platform inserts with swing gate • Platform top auxiliary rail • Arc Pro 275™ Heavy-Duty Welder package • Welder Ready package • Weld leads to platform • Air line to platform • Biodegradable hydraulic oil • Hostile environment package • Deluxe hostile environment package • Aircraft protection package (6 ft platform only) • Thumb rocker steer • Tool tray • Pipe cradle (pair) • Panel cradle package* • Platform work lights • Lockable platform control box covers • Light package

• 12 V DC auxiliary power • Anti-restart engine protection • Auto engine fault shutdown

POWER OPTIONS • AC generator packages (110V/60Hz 220V/50Hz, 3000W) • Cold Weather Packages • Diesel scrubber/spark arrestor muffler (catalytic muffler) • Intake air pre-cleaner

Genie United States

Genie Europe

Distributed By:

18340 NE 76th Street P.O. Box 97030 Redmond, Washington 98073-9730

The Maltings Wharf Road Grantham NG31 6BH UK

POWER

* Available on select models

Telephone +1 (425) 881-1800 Toll Free in USA/Canada +1 (800) 536-1800 Fax +1 (425) 883-3475

Telephone +44 (0)1476 584333 Fax +44 (0)1476 584334 Email: AWP-InfoEurope@terex.com

www.genieindustries.com

SELF-PROPELLED TELESCOPIC BOOMS

S -120 & S -125 TM

Specifications A E

A E

RANGE OF MOTION STM-120 B

C G

G F

MODELS

S -120

STM-125

MEASUREMENTS Working height maximum* Platform height maximum Horizontal reach maximum Below ground reach A Platform length - 8 ft model Platform length - 6 ft model B Platform width - 8 ft model Platform width - 6 ft model C Height - stowed D Length - stowed Length - transport (jib tucked under) E Width - axles retracted Width - axles extended F Wheelbase G Ground clearance - center

Metric

126 ft 120 ft 75 ft 6 ft 6 in 3 ft 2 ft 6 in 8 ft 6 ft 10 ft 1 in 42 ft 8 in ——— 8 ft 2 in 11 ft 12 ft 1 ft 5.5 in

38.58 m 36.58 m 22.86 m 1.98 m .91 m .76 m 2.44 m 1.83 m 3.07 m 13.00 m ——— 2.49 m 3.35 m 3.66 m .44 m

131 ft 2 in 125 ft 2 in 80 ft 10 ft 9 in 3 ft 2 ft 6 in 8 ft 6 ft 10 ft 1 in 46 ft 9 in 39 ft 11 in 8 ft 2 in 11 ft 12 ft 1 ft 5.5 in

40.15 m 38.15 m 24.38 m 3.27 m .91 m .76 m 2.44 m 1.83 m 3.07 m 14.25 m 12.17 m 2.49 m 3.35 m 3.66 m .44 m

750 lbs 160° —— 360° continuous 5 ft 6 in 4 ft 1 in 3.0 mph

340 kg

227 kg

1.68 m 1.24 m 4.8 km/h

500 lbs 160° 135° 360° continuous 5 ft 6 in 4 ft 1 in 3.0 mph

1.68 m 1.24 m 4.8 km/h

0.68 mph

1.1 km/h

0.68 mph

1.1 km/h

PRODUCTIVITY Lift capacity Platform rotation Vertical jib rotation Turntable rotation Turntable tailswing - axle retracted Turntable tailswing - axle extended Drive speed - stowed Drive speed - raised/extended below 80 ft Drive speed - raised/extended above 80 ft Gradeability - stowed** Turning radius - axle retracted: inside outside Turning radius - axle extended: inside outside Controls Tires - RT lug RT solid

0.34 mph .55 km/h 40% 13 ft 2 in 4.01 m 22 ft 2 in 6.75 m 8 ft 6 in 2.59 m 18 ft 10 in 5.74 m 12 V DC proportional 445/65 D22.5 445/65 D24

RANGE OF MOTION STM-125

0.34 mph .55 km/h 40% 13 ft 2 in 4.01 m 22 ft 2 in 6.75 m 8 ft 6 in 2.59 m 18 ft 10 in 5.74 m 12 V DC proportional 445/65 D22.5 445/65 D24

POWER Power source Auxiliary power unit Hydraulic tank capacity Fuel tank capacity

Deutz TD 2011 L04i 4-cylinder turbo diesel, 74 hp (55 kW) Perkins 804-33T 4-cylinder turbo diesel, 83 hp (62 kW) 12 V DC 12 V DC 55 gal 208 L 55 gal 208 L 40 gal 151 L 40 gal 151 L

WEIGHT*** 4WD

STANDARDS COMPLIANCE www.genieindustries.com

44,340 lbs

20,112 kg

44,640 lbs

ANSI A92.5, CSA B354.4, EN 280, AS 1418.10

20,248 kg * The metric equivalent of working height adds 2 m to platform height. U.S. adds 6 ft to platform height. ** Gradeability applies to driving on slopes. See operator’s manual for details regarding slope ratings. *** Weight will vary depending on options and/or country standards.

SELF-PROPELLED TELESCOPIC BOOMS

S -120 & S -125 TM

Specifications A E

A E

RANGE OF MOTION STM-120 B

C G

G F

MODELS

S -120

STM-125

Metric

126 ft 120 ft 75 ft 6 ft 6 in 3 ft 2 ft 6 in 8 ft 6 ft 10 ft 1 in 42 ft 8 in ——— 8 ft 2 in 11 ft 12 ft 1 ft 5.5 in

38.58 m 36.58 m 22.86 m 1.98 m .91 m .76 m 2.44 m 1.83 m 3.07 m 13.00 m ——— 2.49 m 3.35 m 3.66 m .44 m

131 ft 2 in 125 ft 2 in 80 ft 10 ft 9 in 3 ft 2 ft 6 in 8 ft 6 ft 10 ft 1 in 46 ft 9 in 39 ft 11 in 8 ft 2 in 11 ft 12 ft 1 ft 5.5 in

40.15 m 38.15 m 24.38 m 3.27 m .91 m .76 m 2.44 m 1.83 m 3.07 m 14.25 m 12.17 m 2.49 m 3.35 m 3.66 m .44 m

750 lbs 160° —— 360° continuous 5 ft 6 in 4 ft 1 in 3.0 mph

340 kg

227 kg

1.68 m 1.24 m 4.8 km/h

500 lbs 160° 135° 360° continuous 5 ft 6 in 4 ft 1 in 3.0 mph

1.68 m 1.24 m 4.8 km/h

0.68 mph

1.1 km/h

0.68 mph

1.1 km/h

PRODUCTIVITY Lift capacity Platform rotation Vertical jib rotation Turntable rotation Turntable tailswing - axle retracted Turntable tailswing - axle extended Drive speed - stowed Drive speed - raised/extended below 80 ft Drive speed - raised/extended above 80 ft Gradeability - stowed** Turning radius - axle retracted: inside outside Turning radius - axle extended: inside outside Controls Tires - RT lug RT solid

0.34 mph .55 km/h 40% 13 ft 2 in 4.01 m 22 ft 2 in 6.75 m 8 ft 6 in 2.59 m 18 ft 10 in 5.74 m 12 V DC proportional 445/65 D22.5 445/65 D24

RANGE OF MOTION STM-125

0.34 mph .55 km/h 40% 13 ft 2 in 4.01 m 22 ft 2 in 6.75 m 8 ft 6 in 2.59 m 18 ft 10 in 5.74 m 12 V DC proportional 445/65 D22.5 445/65 D24

POWER Power source Auxiliary power unit Hydraulic tank capacity Fuel tank capacity

Deutz TD 2011 L04i 4-cylinder turbo diesel, 74 hp (55 kW) Perkins 804-33T 4-cylinder turbo diesel, 83 hp (62 kW) 12 V DC 12 V DC 55 gal 208 L 55 gal 208 L 40 gal 151 L 40 gal 151 L

WEIGHT*** 4WD

STANDARDS COMPLIANCE www.genieindustries.com

44,340 lbs

20,112 kg

44,640 lbs

ANSI A92.5, CSA B354.4, EN 280, AS 1418.10

SELF-PROPELLED ARTICULATING BOOMS

Z -135/70 TM

Specifications A

C G F

MODEL

ZTM-135/70

MEASUREMENTS Working height maximum* Platform height maximum Horizontal reach max - riser extended Horizontal reach max - riser retracted Up and over clearance maximum riser extended riser retracted Below ground reach A Platform length - 8 ft / 6 ft model B Platform width - 8 ft / 6 ft model C Height - stowed D Length - stowed E Width - axles extended Width - axles retracted F Wheelbase - axles extended Wheelbase - axles retracted G Ground clearance - center

Metric

141 ft 135 ft 59 ft 2 in 69 ft 9 in

43.15 m 41.15 m 18.03 m 21.26 m

75 ft 6 in 32 ft 6 in 19 ft 3 in 3 ft / 2 ft 6 in 8 ft / 6 ft 10 ft 1 in 42 ft 5 in 12 ft 11 in 8 ft 1 in 13 ft 6 in 15 ft 6 in 1 ft 8 in

23.01 m 9.91 m 5.87 m .91 m / .76 m 2.44 m / 1.83 m 3.07 m 12.93 m 3.94 m 2.46 m 4.11 m 4.72 m .51 m

RANGE OF MOTION ZTM-135/70 140 ft

42.67 m

130 ft

39.62 m

120 ft

36.58 m

110 ft

33.53 m

100 ft

30.48 m

90 ft

27.43 m

80 ft

24.38 m

70 ft

21.34 m

60 ft

18.29 m

50 ft

15.24 m

40 ft

12.19 m

PRODUCTIVITY

30 ft

9.14 m

Lift capacity Platform rotation Vertical jib rotation Turntable rotation Turntable tailswing - axles extended riser up Turntable tailswing - riser down Drive speed - stowed Drive speed - raised Lift speed to full height Gradeability - stowed** Inside turning radius - axles extended Inside turning radius - axles retracted Outside turning radius - axles extended Outside turning radius - axles retracted Controls Tires

600 lbs 272 kg 160° 110° 360° continuous 2 ft 7 in .79 m 14 ft 4.27 m 3.0 mph 4.8 km/h 0.68 mph 1.1 km/h 96 sec 45% 7 ft 6 in 2.29 m 18 ft 1 in 5.51 m 18 ft 6 in 5.64 m 25 ft 6 in 7.77 m 12 V DC proportional 445/65 D22.5 18 ply foam-filled

20 ft

6.1 m

10 ft

3.05 m

0 ft 0m

-10 ft

-3.05 m

-20 ft

-6.1 m

-30 ft -20 ft -10 ft

0 ft

10 ft

20 ft

30 ft

-9.14 m

3.05 m

6.1 m

9.14 m 12.19 m 15.24 m 18.29 m 21.34 m

-6.1 m

-3.05 m

40 ft

50 ft

60 ft

POWER Power source

Deutz Diesel TD 2011 L04i 4-cylinder turbo diesel, 74 hp (55 kW) Perkins Diesel 804-33T 4-cylinder turbo diesel, 83 hp (62 kW) Auxiliary power unit 12 V DC Hydraulic tank capacity Fuel tank capacity

65 gal 40 gal

246.1 L 151.4 L

WEIGHT*** 44,900 lbs

STANDARDS COMPLIANCE www.genieindustries.com

20,366 kg

ANSI A92.5, CSA B354.4, CE Compliance, AS 1418.10

* The metric equivalent of working height adds 2 m to platform height. U.S. adds 6 ft to platform height. ** Gradeability applies to driving on slopes. See operator’s manual for details regarding slope ratings. *** Weight will vary depending on options and/or country standards.

70 ft

SELF-PROPELLED ARTICULATING BOOMS

Z -135/70 TM

Features EASILY CONFIGURED TO MEET YOUR NEEDS PLATFORM OPTIONS • Steel 8 ft (2.44 m) (standard) • Steel 6 ft (1.83 m) • Steel 6 or 8 ft (1.83 or 2.44 m) tri-entry JIB • 12 to 20 ft (3.66 to 6.10 m) Jib-Extend™ ENGINE OPTIONS • Deutz turbo diesel, 74 hp (55 kW) • Perkins turbo diesel, 83 hp (62 kW) DRIVE/STEER • 4WD (standard) • 4WS (standard) TIRE • Extra-wide rough terrain foam-filled (standard)

* Available on select models

STANDARD FEATURES MEASUREMENTS • 141 ft (43.15 m) working height • 69 ft 9 in (21.26 m) horizontal reach • 75 ft 6 in (23.01 m) up and over clearance • Up to 600 lb (272 kg) lift capacity PRODUCTIVITY • Xchassis™ extendable axles • 12 to 20 ft (3.66 to 6.10 m) Jib-Extend™ • Self-leveling platform • Hydraulic platform rotation • Fully proportional joystick controls • On-board full diagnostics and engine monitoring display • ALC 1000 electronic control system • Hydraulic oil cooler • Drive enable • AC power cord to platform • Horn • Hour meter • Tilt alarm • Descent, motion, & travel alarms • 360° continuous turntable rotation • Four wheel high angle steer • Four steering modes: front, rear, crab and coordinated • Four wheel brakes • Full-time positive traction 4WD • Adjustable foot switch timeout • Two speed wheel motors • Configurable controls to limit lift height to 91 ft (27.74 m) • Engine status display POWER • All engines are emissions compliant • 12 V DC auxiliary power • Engine protection package • Deutz intake air heater • Swing out engine tray

Genie United States

Genie Europe

18340 NE 76th Street P.O. Box 97030 Redmond, Washington 98073-9730

The Maltings Wharf Road Grantham NG31 6BH UK

Telephone +1 (425) 881-1800 Toll Free in USA/Canada +1 (800) 536-1800 Fax +1 (425) 883-3475

OPTIONS & ACCESSORIES PRODUCTIVITY OPTIONS • Platform swing gate • Half-mesh platform inserts with swing gate • Platform top auxiliary rail • Air line to platform • Arc Pro 275™ Heavy-Duty Welder package • Welder Ready package • Weld leads to platform • Biodegradable hydraulic oil • Hostile environment kit • Deluxe hostile environment kit • Thumb rocker steer • Tool tray • Pipe cradle (pair) • Flashing beacon • Panel cradle package* • Platform work lights • Front driving lights • Lockable platform control box covers • Light package POWER OPTIONS • AC generator packages (110V/60Hz, 3000W or 220V/50Hz, 2500W) • Cold Weather Packages • Arctic Packages • Diesel scrubber muffler (Cummins) • Diesel scrubber/spark arrestor muffler (Deutz and Perkins) • Diesel spark arrestor muffler (Deutz and Perkins)

Distributed By:

Telephone +44 (0)1476 584333 Fax +44 (0)1476 584334 Email: AWP-InfoEurope@terex.com

www.genieindustries.com

SELF-PROPELLED SCISSOR LIFTS

GS -1530 & GS -1930 TM

Specifications MODELS MEASUREMENTS Working height maximum* A Platform height maximum B Platform height stowed C Platform length - outside extended Slide-out platform extension deck D Platform width - outside Guardrail height: fixed rails fold down (CE) Toeboard height E Height-stowed: fixed rails folding guardrails (CE) rails folded F Length-stowed Length-stowed extended G Width H Wheelbase I Ground clearance - center J - with pothole guards deployed

GSTM-1530

GSTM-1930

Metric

21 ft 15 ft 3 ft 2.2 in 5 ft 4 in 8 ft 4 in 3 ft 2 ft 5 in 3 ft 3 in 3 ft 7 in 6 in 6 ft 5 in 6 ft 8 in 5 ft 8 in 6 ft 9 ft 2 ft 6 in 4 ft 4 in 2.4 in .75 in

6.57 m 4.57 m .97 m 1.63 m 2.54 m .91 m .74 m .99 m 1.10 m .15 m 1.96 m 2.03 m 1.73 m 1.83 m 2.74 m .76 m 1.32 m .06 m .02 m

25 ft 19 ft 3 ft 3.5 in 5 ft 4 in 8 ft 4 in 3 ft 2 ft 5 in 3 ft 3 in 3 ft 7 in 6 in 6 ft 7 in 6 ft 11 in 5 ft 9 in 6 ft 9 ft 2 ft 6 in 4 ft 4 in 2.4 in .75 in

7.79 m 5.79 m 1.00 m 1.63 m 2.54 m .91 m .74 m .99 m 1.10 m .15 m 2.00 m 2.11 m 1.75 m 1.83 m 2.74 m .76 m 1.32 m .06 m .02 m

2 600 lbs 250 lbs 2.5 mph 0.5 mph 30% zero 5 ft 1 in 16 / 29 sec proportional dual front wheel dual rear wheel 12 x 4.5 x 8 in

2 272 kg 113 kg 4.0 km/h 0.8 km/h

2 500 lbs 250 lbs 2.5 mph 0.5 mph 25% zero 5 ft 1 in 16 / 25 sec proportional dual front wheel dual rear wheel 12 x 4.5 x 8 in

2 227 kg 113 kg 4.0 km/h 0.8 km/h

H F

PRODUCTIVITY Maximum platform occupancy** Lift capacity Lift capacity - extension deck Drive speed - stowed Drive speed - raised Gradeability - stowed*** Turning radius - inside Turning radius - outside Raise / lower speed Controls Drive Multiple disc brakes Tires - solid non-marking

zero 1.55 m 16 / 29 sec

30 x 11 x 20 cm

zero 1.55 m 16 / 25 sec

30 x 11 x 20 cm

POWER Power source Hydraulic system capacity

24 V DC (four 6 V 225 Ah batteries) 3.75 gal 14.2 L

2,575 lbs 2,718 lbs —

2,702 lbs 3,302 lbs 3,302 lbs

WEIGHT**** ANSI, CSA CE indoor AUS indoor

STANDARDS COMPLIANCE

1,168 kg 1,233 kg —

ANSI A92.6, CSA B354.2, CE Compliance, AS 1418.10

* The metric equivalent of working height adds 2 m to platform height. U.S. adds 6 ft to platform height. ** CE/AUS markets: GS-1530 and GS-1930 are indoor use only–2 person maximum occupancy. GS-1532 and GS-1932 are indoor/outdoor use–1 person maximum. *** Gradeability applies to driving on slopes, see operator’s manual for details regarding slope ratings. **** Weight will vary depending on options and/or country standards.

www.genieindustries.com

1,226 kg 1,498 kg 1,498 kg

J G

SELF-PROPELLED SCISSOR LIFTS

GS -1530 & GS -1930 TM

Features STANDARD FEATURES MEASUREMENTS ™

GS -1530 • 21 ft (6.57 m) working height • Up to 600 lb (272 kg) lift capacity GS™-1930 • 25 ft (7.79 m) working height • Up to 500 lb (227 kg) lift capacity PRODUCTIVITY • 64 x 29 in (1.63 x .74 m) steel platform • Fixed rail with chain entry gate • Folding rails with half-height swing gate (CE) • 36 in (.91 m) extension deck • Dual front wheel drive • Proportional lift and drive • Universal 20 amp smart charger • Rear recessed charger receptacle • 25% gradeability • Platform control with battery charge indicator and diagnostic display • On-board diagnostic system • AC power to platform • Lanyard attachment points • Manual platform lowering valve • Emergency stop at both platform and ground controls • Rear wheel multiple disc brakes • Front wheel hydraulic dynamic braking • Brake release • Swing-out component trays • Solid non-marking tires • Pothole guards • Tilt level sensor with audible alarm • Descent alarm • Electronic horn • Hour meter

OPTIONS & ACCESSORIES PRODUCTIVITY OPTIONS • • • • • • •

Folding rails with half-height swing gate Platform swing gate, half-height Air line to platform Dual flashing beacons Motion package Automotive horn Biodegradable hydraulic fluid

POWER OPTIONS • Power inverter (120 V/60 Hz) (not available GS™-1930, GS™-1932 CE) • EE rating

POWER • 24 V DC (four 6 V 225 Ah batteries)

Genie United States

Genie Europe

18340 NE 76th Street P.O. Box 97030 Redmond, Washington 98073-9730

The Maltings Wharf Road Grantham NG31 6BH UK

Telephone +1 (425) 881-1800 Toll Free in USA/Canada +1 (800)-536-1800 Fax +1 (425) 883-3475

Distributed By:

Telephone +44 (0)1476 584333 Fax +44 (0)1476 584334 Email: AWP-InfoEurope@terex.com

Effective Date: January, 2011. Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and we make no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation, Genie Industries, Inc. and/or their subsidiaries in the U.S.A. and many other countries and all rights are reserved. Terex is a Registered Trademark of Terex Corporation in the U.S.A. and many other countries. Genie is a Registered Trademark of Genie Industries, Inc. in the U.S.A. and many other countries. Genie is a Terex Brand. © 2011 Terex Corporation. GS30 0210L. Part No. 109377

www.genieindustries.com

SELF-PROPELLED SCISSOR LIFTS

GS -2032, GS -2632 & GS -3232 TM

Specifications MODELS MEASUREMENTS Working height maximum* A Platform height maximum B Platform height stowed C Platform length - outside extended Slide-out platform extension deck D Platform width - outside Guardrail height: fixed rails fold down rails (CE) Toeboard height E Height - stowed fixed rails folding guardrails (CE) rails folded F Length - stowed Length - extended G Width H Wheelbase I Ground clearance - center J - with pothole guards deployed

GSTM-2032 US

GSTM-2632 Metric

GSTM-3232

Metric

26 ft 20 ft 3 ft 4.5 in 7 ft 5 in 10 ft 5 in 3 ft 2 ft 8 in 3 ft 3 in 3 ft 7 in 6 in

8.10 m 6.10 m 1.03 m 2.26 m 3.18 m .91 m .81 m .99 m 1.10 m .15 m

32 ft 26 ft 3 ft 9.5 in 7 ft 5 in 10 ft 5 in 3 ft 2 ft 8 in ——— 3 ft 7 in 6 in

9.92 m 7.92 m 1.16 m 2.26 m 3.18 m .91 m .81 m ——— 1.10 m .15 m

38 ft 32 ft 4 ft 2.75 in 7 ft 5 in 10 ft 5 in 3 ft 2 ft 8 in ——— 3 ft 7 in 6 in

11.75 m 9.75 m 1.29 m 2.26 m 3.18 m .91 m .81 m ——— 1.10 m .15 m

6 ft 8 in 7 ft 5 ft 9 in 8 ft 10 ft 11 in 2 ft 8 in 6 ft 1 in 3.5 in .75 in

2.03 m 2.13 m 1.75 m 2.44 m 3.33 m .81 m 1.85 m .09 m .02 m

——— 7 ft 5 in 6 ft 3 in 8 ft 10 ft 11 in 2 ft 8 in 6 ft 1 in 3.5 in .75 in

——— 2.26 m 1.91 m 2.44 m 3.33 m .81 m 1.85 m .09 m .02 m

——— 8 ft 6 ft 8 in 8 ft 10 ft 11 in 2 ft 8 in 6 ft 1 in 3.5 in .75 in

——— 2.43 m 2.03 m 2.43 m 3.33 m .81 m 1.85 m .09 m .02 m

E B

H F

PRODUCTIVITY Maximum platform occupancy** Lift capacity Extension deck capacity Drive height Drive speed - stowed Drive speed - raised Gradeability - stowed*** Maximum outrigger leveling: front to back side to side Turning radius - inside Turning radius - outside Raise / lower speed Controls Drive Multiple disc brakes Tires - solid non-marking

2 2 800 lbs 363 kg 250 lbs 113 kg full height 2.2 mph 3.5 km/h 0.5 mph 0.8 km/h 30% ——— ——— ——— ——— zero zero 7 ft 2.13 m 30 / 34 sec 30 / 34 sec proportional dual front wheel dual rear wheel 15 x 5 x 11 in 38 x 13 x 28 cm

2 2 500 lbs 227 kg 250 lbs 113 kg full height 2.2 mph 3.5 km/h 0.5 mph 0.8 km/h 25% ——— ——— ——— ——— zero zero 7 ft 2.13 m 30 / 40 sec 30 / 40 sec proportional dual front wheel dual rear wheel 15 x 5 x 11 in 38 x 13 x 28 cm

2 2 500 lbs 227 kg 250 lbs 113 kg 22 ft 6.71 m 2.2 mph 3.5 km/h 0.5 mph 0.8 km/h 25% 3° 5° zero zero 7 ft 2.13 m 57 / 40 sec 57 / 40 sec proportional dual front wheel dual rear wheel 15 x 5 x 11 in 38 x 13 x 28 cm

24 V DC (four 6V 225 Ah batteries) 3.75 gal 14.2 L

3,574 lbs 4,024 lbs

4,413 lbs 4,313 lbs

5,185 lbs 5,185 lbs

POWER Power source Hydraulic system capacity

WEIGHT**** ANSI, CSA CE, AUS

STANDARDS COMPLIANCE

1,621 kg 1,825 kg

2,002 kg 1,956 kg

ANSI A92.6, CSA B354.2, CE Compliance, AS 1418.10

* The metric equivalent of working height adds 2 m to platform height. U.S. adds 6 ft to platform height. ** CE/AUS markets: GS-2632 and GS-3232 indoor use only. GS-2032 outdoor use-one person maximum occupancy. *** Gradeability applies to driving on slopes. See operator’s manual for details regarding slope ratings. **** Weight will vary depending on options and/or country standards.

www.genieindustries.com

2,352 kg 2,352 kg

J G

SELF-PROPELLED SCISSOR LIFTS

GS -2032, GS -2632 & GS -3232 TM

Features STANDARD FEATURES MEASUREMENTS GS™-2032 • 26 ft (8.10 m) working height • Up to 800 lb (363 kg) lift capacity GS™-2632 • 32 ft (9.92 m) working height • Up to 500 lb (227 kg) lift capacity GS™-3232 • 38 ft (11.75 m) working height • Up to 500 lb (227 kg) lift capacity

OPTIONS & ACCESSORIES PRODUCTIVITY OPTIONS • Folding rails with half-height swing gate (GS™-2032) • Platform swing gate, half-height (GS™-2032) • Air line to platform • Dual flashing beacons • Motion package • Automotive horn • Biodegradable hydraulic fluid

POWER OPTIONS PRODUCTIVITY • 89 x 32 in (2.26 x .81 m) steel platform • Power Inverter (120 V/60 Hz) • 36 in (.91 m) extension deck • EE rating • Fixed rail with chain entry gate (standard GS-2032) • Folding rails with half-height swing gate (standard on all CE, GS-2632, GS-3232) • Automatic leveling outriggers (GS-3232 only) • Dual front wheel drive • Universal 20 amp smart charger • Rear recessed charger receptacle • Proportional lift and drive • Platfrom control with battery charge indicator and diagnostic display • On-board diagnostic system • AC power to platform • Lanyard attachment points • Manual platform lowering valve • Emergency stop at both platform and ground controls • Rear wheel multiple disc brakes • Front wheel hydraulic dynamic braking • Brake release • Swing-out component trays • Solid non-marking tires • Pothole guards • Tilt level sensor with audible alarm • Descent alarm • Electronic horn • Hour meter POWER • 24 V DC (four 6 V 225 Ah batteries)

Genie United States

Genie Europe

18340 NE 76th Street P.O. Box 97030 Redmond, Washington 98073-9730

The Maltings Wharf Road Grantham NG31 6BH UK

Telephone +1 (425) 881-1800 Toll Free in USA/Canada +1 800-536-1800 Fax +1 (425) 883-3475

Distributed By:

Telephone +44 (0)1476 584333 Fax +44 (0)1476 584334 Email: AWP-InfoEurope@terex.com

Effective Date: April, 2011. Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and we make no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation, Genie Industries, Inc. and/or their subsidiaries in the U.S.A. and many other countries and all rights are reserved. Terex® is a Registered Trademark of Terex Corporation in the U.S.A. and many other countries. Genie® is a Registered Trademark of Genie Industries, Inc. in the U.S.A. and many other countries. Genie is a Terex Brand. © 2011 Terex Corporation. GS32 0210I. Part No. 109378

www.genieindustries.com

SELF-PROPELLED SCISSOR LIFTS

GS -2669 RT, GS -3369 RT, GS -4069 RT TM

Specifications MODELS MEASUREMENTS Working height maximum* A Platform height maximum Drive height B Platform height - stowed C Platform length - outside extended Slide-out platform extension deck(ANSI) Slide-out platform extension deck(CE/Aus) D Platform width - outside Toeboard height E Height - stowed** rails lowered F Length - stowed platform extended with outriggers G Width H Wheelbase I Ground clearance - center

GSTM-2669 RT

GSTM-3369 RT

GSTM-4069 RT

Metric

32 ft 26 ft 26 ft 4 ft 10 in 9 ft 2in 14 ft 2 in 5 ft 3 ft 5 ft 3 in 6 in 8 ft 6 in 6 ft 3.5 in 10 ft 3 in 14 ft 9 in 12 ft 4 in 5 ft 9 in 7 ft 6 in 9.5 in

9.75 m 7.9 m 7.9 m 1.47 m 2.79 m 3.96 m 1.52 m 0.91 m 1.6 m 0.15 m 2.59 m 1.92 m 3.12 m 4.5 m 3.76 m 1.75 m 2.29 m 0.24 m

39 ft 32 ft 8 in 32 ft 8 in 4 ft 10 in 9 ft 2in 14 ft 2 in 5 ft 3 ft 5 ft 3 in 6 in 8 ft 6 in 6 ft 3.5 in 10 ft 3 in 14 ft 9 in 12 ft 4 in 5 ft 9 in 7 ft 6 in 9.5 in

11.9 m 9.96 m 9.96 m 1.47 m 2.79 m 3.96 m 1.52 m 0.91 m 1.6 m 0.15 m 2.59 m 1.92 m 3.12 m 4.5 m 3.76 m 1.75 m 2.29 m 0.24 m

46 ft 40 ft 40 ft 5 ft 5 in 9 ft 2in 14 ft 2 in 5 ft 3 ft 5 ft 3 in 6 in 9 ft 6 ft 10 in 10 ft 3 in 14 ft 9 in 12 ft 4 in 5 ft 9 in 7 ft 6 in 9.5 in

14.02 m 12.2 m 12.2 m 1.65 m 2.79 m 3.96 m 1.52 m 0.91 m 1.6 m 0.15 m 2.74 m 2.08 m 3.12 m 4.5 m 3.76 m 1.75 m 2.29 m 0.24 m

4 1,500 lbs 300 lbs 3.5 mph 0.3 mph 40%

680 kg 136 kg 6.1 km/h 0.5 km/h

4 1,000 lbs 300 lbs 3.5 mph 0.3 mph 35%

454 kg 136 kg 6.1 km/h 0.5 km/h

3 800 lbs 300 lbs 3.5 mph 0.3 mph 35%

363 kg 136 kg 6.1 km/h 0.5 km/h

H F

E I G

PRODUCTIVITY Maximum platform occupancy*** Lift capacity Extension deck capacity Drive speed - stowed Drive speed - raised Gradeability - stowed**** Maximum outrigger leveling: front/back uphill side to side Turning radius - inside Turning radius - outside Raise/lower speed Controls Drive Tires - rough terrain

5.3°/4.2° 11.7° 83 in 181.2 in 30/40 sec proportional four wheel 12x26 in

2.11 m 4.6 m

83 in 181.2 in 40/45 sec

2.11 m 4.6 m

83 in 181.2 in 50/60 sec

2.11 m 4.6 m

30x66 cm

12x26 in

30x66 cm

12x26 in

30x66 cm

Kubota DF-972 gas/LPG 29 hp Kubota D-1105 Diesel 24.8 hp Perkins 403D-11 Diesel 25 hp 10 gal 37.9 L 10 gal 18 gal 68.1 L 18 gal

37.9 L 68.1 L

10 gal 18 gal

37.9 L 68.1 L

7,235 lbs 8,100 lbs

3,499 kg 3,891 kg

10,190 lbs 11,055 lbs

4,622 kg 5,015 kg

POWER Power source

Fuel tank capacity Hydraulic system capacity

WEIGHT***** with outriggers

STANDARDS COMPLIANCE

3,282 kg 3,674 kg

7,715 lbs 8,580 lbs

ANSI A92.6, CSA B354.2, CE Compliance, AS 1418.10

* The metric equivalent of working height adds 2 m to platform height. U.S. adds 6 ft to platform height. ** Based on RT tires; deduct 2 in (5.8 cm) for turf and non-marking tires. *** CE/AUS markets: GS™-3369 and GS™-4069 are limited to 2 person platform occupancy when used outdoors. **** Gradeability applies to driving on slopes. Gradeability may vary depending on the weight of options installed on machine. See operator’s manual for details regarding slope ratings. ***** Weight varies depending on options and country standards.

www.genieindustries.com

SELF-PROPELLED SCISSOR LIFTS

GS -2669 RT, GS -3369 RT, GS -4069 RT TM

Features STANDARD FEATURES MEASUREMENTS ™

GS -2669 RT • 32 ft (9.75 m) working height • Up to 1,500 lb (680 kg) lift capacity GS™-3369 RT • 39 ft (11.90 m) working height • Up to 1,000 lb (454 kg) lift capacity GS™-4069 RT • 46 ft (14.02 m) working height • Up to 800 lb (363 kg) lift capacity PRODUCTIVITY • 110 x 63 in (2.79 x 1.6m) steel frame platform with replaceable aluminum deck • 60 in (1.52 m) extension deck (ANSI) • Folding guardrails • Proportional lift and drive • AC power to platform • Full height swing gate • 4WD • Front oscillating axle • Positive traction control • Four-wheel braking • Swing-out engine tray • Foam-filled rough terrain tires (eco fill) • Tilt level sensor with audible alarm • Descent alarm • Horn • Hour meter

OPTIONS & ACCESSORIES PRODUCTIVITY • Automatic leveling hydraulic outriggers • Air line to platform • Non-marking rough terrain tires 12 x 26 in (30 x 66 cm) • Dual flashing beacons • Motion alarm POWER OPTIONS • • • • • • • •

Kubota gas/LPG 29 hp (21.7 kW) Kubota diesel 24.8 hp (18.5 kW) Perkins diesel 25 hp (19.5 kW) 3000 AC Watt generator (110V/60 Hz) Diesel Scrubber (Perkins) Cold weather package Hydraulic oil cooler LPG steel tank only, 33.5 lb capacity

Genie United States

Genie Europe

18340 NE 76th Street P.O. Box 97030 Redmond, Washington 98073-9730

The Maltings Wharf Road Grantham NG31 6BH UK

Telephone +1 (425) 881-1800 Toll Free in USA/Canada +1 (800)-536-1800 Fax +1 (425) 883-3475

Distributed By:

Telephone +44 (0)1476 584333 Fax +44 (0)1476 584334 Email: AWP-InfoEurope@terex.com

Effective Date: May, 2011. Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and we make no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation, Genie Industries, Inc. and/or their subsidiaries in the U.S.A. and many other countries and all rights are reserved. Terex is a Registered Trademark of Terex Corporation in the U.S.A. and many other countries. Genie is a Registered Trademark of Genie Industries, Inc. in the U.S.A. and many other countries. Genie is a Terex Brand. © 2011 Terex Corporation. GS69RT 0210K. Part No. 127284

www.genieindustries.com

SELF-PROPELLED SCISSOR LIFTS

GS -3384 RT TM

Specifications MODEL

GSTM-3384 RT

MEASUREMENTS Working height maximum* A Platform height maximum B Platform height - stowed** C Platform length: outside, extended - single deck outside, extended - dual deck D Slide-out platform extension deck - front E Slide-out platform extension deck - rear F Platform width - outside G Height - stowed: folding guardrails rails lowered H Length - stowed: single deck dual deck with outriggers I Width: standard tires high flotation tires J Wheelbase K Ground clearance - center

Metric

39 ft 33 ft 5 ft 1 in 13 ft .5 in 17 ft 6.25 in 21 ft 6.5 in 5 ft 4 ft 6 ft 8 ft 9.5 in 6 ft 6.75 in 12 ft 11.25 in 13 ft 5 in 16 ft 7 ft 7 ft 11 in 9 ft 4 in 13 in

12.06 m 10.06 m 1.55 m 3.98 m 5.34 m 6.57 m 1.52 m 1.22 m 1.83 m 2.68 m 2.0 m 3.94 m 3.98 m 4.88 m 2.13 m 2.41 m 2.84 m .33 m

7 2,500 lbs 500 lbs 4.0 mph 0.7 mph 50% 7º 12º 10 ft 1.5 in 19 ft 6 in 45/29 sec proportional four wheel 10 x 31 in

7 1,134 kg 227 kg 6.4 km/h 1.1 km/h

G B

J H F

K I C

PRODUCTIVITY Maximum platform occupancy Lift capacity Lift capacity - extension deck Drive speed - stowed Drive speed - raised Gradeability - stowed*** Maximum outrigger leveling: front to back side to side Turning radius - inside Turning radius - outside Raise/lower speed Controls Drive Tires - foam-filled rough terrain

3.09 m 5.94 m

25 x 79 cm A

POWER Power source

Auxiliary Power unit Fuel tank capacity Hydraulic system capacity

Ford DSG-423 4 cylinder gas/LPG 75 hp (56 kW) Deutz D2011L03i 3 cylinder diesel 49 hp (36 kW) air cooled 12 V DC 30 gal 113.6 L 30 gal 113.6 L

WEIGHT**** with outriggers

STANDARDS COMPLIANCE

12,005 lbs 13,680 lbs

5,445 kg 6,205 kg

ANSI A92.6, CSA B354.2, CE Compliance, AS 1418.10

* The metric equivalent of working height adds 2 m to platform height. U.S. adds 6 ft to platform height. ** Based on RT tires. Deduct 2 in (5.8 cm) for turf and non-marking. *** Gradeability applies to driving on slopes. See operator’s manual for details regarding slope ratings. **** Weight will vary depending on options and/or country standards.

www.genieindustries.com

SELF-PROPELLED SCISSOR LIFTS

GS -3384 RT TM

Features STANDARD FEATURES

OPTIONS & ACCESSORIES

MEASUREMENTS

PRODUCTIVITY OPTIONS

• 39 ft (12.06 m) working height • Up to 2,500 lb (1,134 kg) lift capacity

• Dual slide-out platform extension deck package 5 ft (1.52 m) front and 4 ft (1.22 m) rear • Automatic leveling hydraulic outriggers • Air line to platform • Non-marking rough terrain tires 10 x 31 in (25 x 79 cm) • High flotation air-filled tires 17 x 33 in (43 x 84 cm) • High flotation foam-filled tires 16 x 33 in (41 x 84 cm) • Dual flashing beacons • Motion alarm

PRODUCTIVITY • 156.5 x 72 in (3.98 x 1.83 m) steel frame platform • 60 in (1.52 cm) extension deck • Replaceable aluminum deck • Folding guardrails • Proportional lift and drive • Onboard diagnostic system • AC power to platform • Full height swing gate • Two self-closing gates • 4WD • Positive traction control • Four-wheel braking • Slide-out engine tray • Foam-filled rough terrain tires (eco fill) • Tilt level sensor with audible alarm • Descent alarm • Horn • Hour meter

POWER OPTIONS • • • • • • •

Ford gas/LPG 75 hp (56 kW) Deutz diesel 49 hp (36 kW) 2000 AC Watt generator (120 V / 60 Hz) Cold weather package Hydraulic oil cooler Diesel scrubber/spark arrestor LPG steel tank only, 33.5 lb capacity

POWER • Deutz diesel 49 hp (36kW)

Genie United States

Genie Europe

18340 NE 76th Street P.O. Box 97030 Redmond, Washington 98073-9730

The Maltings Wharf Road Grantham NG31 6BH UK

Telephone +1 (425) 881-1800 Toll Free in USA/Canada +1 (800)-536-1800 Fax +1 (425) 883-3475

Distributed By:

Telephone +44 (0)1476 584333 Fax +44 (0)1476 584334 Email: AWP-InfoEurope@terex.com

www.genieindustries.com

Model

E Series

el ec t r i c b o o m l i f t s

Features Eight 6V 370 Amp-Hour Deep Cycle Batteries Automatic Traction Control (ATC) Inward Self-Closing Swing Gate 180 Degree Hydraulic Platform Rotator 110V-AC Receptacle on Platform 5 Degree Tilt Alarm/Indicator Light Hourmeter Battery Condition Indicator Lifting/Tie Down Lugs Horn Operator Tool Tray All Motion Alarm

Accessories & Options Platform Worklights Mesh to Top Rail—Bolt-on Aluminum Acrylic Console Shield Cylinder Bellows UL® EE Rating1 Flashing Amber Beacon 1. Not available on Multi-Powered models Please refer to the JLG Aerial Work Platform Sales Manual for additional features and accessories.

Specifications Reach Platform Height E300AJ/E 300AJP 30 ft (9.14 m) E400A/E400AJP 40 ft (12.19 m) E400A Narrow/E400AJP Narrow 40 ft (12.19 m) E450A/E450AJ 45 ft (13.72 m) Horizontal Outreach E/M400A Narrow 21 ft 2 in. (6.45 m) E/M450A 23 ft 1 in. (7.04 m) With Jib E300AJ 20 ft (6.1 m) E/M450AJ 23 ft 9 in. (7.24 m) With JibPLUS E300AJP 20 ft 6 in. (6.25 m) E/M400AJP Narrow 22 ft 5 in. (6.83 m) Up and Over Height E300AJ/E300AJP 13 ft 1 in. (3.99 m) E400A/E400AJP 21 ft 6 in. (6.55 m) E400A Narrow/E400AJP Narrow 21 ft 6 in. (6.55 m) E450A 24 ft 7 in. (7.49 m) E450AJ 25 ft 3 in. (7.7 m) Swing 360 Degrees Non-Continuous Platform Capacity 500 lb (227 kg) Platform Rotator 180 Degrees Hydraulic Jib (range of articulation) E300AJ/E300AJP 144 Degrees (+84, -60) Vertical E400AJP/E400AJP Narrow 144 Degrees (+84, -60) Vertical E450AJ 141 Degrees (+86, -55) Vertical JibPLUS E300AJP/E400AJP/E400AJP Narrow 180 Degrees Horizontal (continued on back page)

Versatility to Meet Your Needs hoose from three popular platform heights and three chassis widths C Non-jib and optional jib models n A utomatic traction control for on and off slab mobility n Z ero emissions and low noise n n

Power to Stay On the Job Longer n n

I ndustry-leading duty cycles Multi-power models provide round-the-clock operation and faster battery charging

Unmatched Reach and Positioning Capabilities E xclusive JibPLUS ® boom option provides 180-degree range of side-to-side movement n 4 8 in. narrow chassis models for narrow aisles n Near vertical jib positioning and access to areas other machines can’t reach n Multiple function operation for efficient maneuvering in tight spaces n

Model

E Series

el ec t r i c B o o m l i f t s

Specifications E300

E400

E450

Dimensions

Platform Size E300AJ/E300AJP 30 x 48 in. (0.76 x 1.22 m) E400A Narrow 30 x 48 in. (0.76 x 1.22 m) E400AJP Narrow 30 x 48 in. (0.76 x 1.22 m) E400A/E400AJP 30 x 60 in. (0.76 x 1.52 m) E450A/E450AJ 30 x 60 in. (0.76 x 1.52 m) Overall Width E300AJ/E300AJP 4 ft (1.22 m) E400A/E400AJP/E450A/E450AJ 5 ft 9 in. (1.75 m) E400A Narrow/E400AJP Narrow 4 ft 11 in. (1.5 m) Tailswing E300AJ/E300AJP/E400A Zero E400AJP/E450A/E450AJ Zero E400A Narrow/E400AJP Narrow 4 in. (10 cm) Stowed Height E300AJ/E300AJP/E400A 6 ft 7 in. (2.0 m) E400AJP/E450AJ 6 ft 7 in. (2.0 m) E400A Narrow/E400AJP Narrow 6 ft 5.75 in. (1.97 m) E450A 6 ft 6 in. (1.98 m) Stowed Length E400A/E400AJP/E400A Narrow 18 ft 1 in. (5.5 m) E400AJP Narrow 18 ft 1 in. (5.5 m) E450A 19 ft 1 in. (5.82 m) With Jib E300AJ 18 ft (5.49 m) E450AJ 21 ft 2 in. (6.45 m) With JibPLUS E300AJP/E400AJP 18 ft 8 in. (5.70 m) E400AJP Narrow 22 ft (6.7 m) Wheelbase E300AJ/E300AJP 5 ft 5 in. (1.65 m) E400A/E400AJP/E400A Narrow 6 ft 7 in. (2.0 m) E400AJP Narrow/E450A/E450AJ 6 ft 7 in. (2.0 m) Ground Clearance E300AJ/E300AJP 4 in. (10 cm) E400A/E400AJP/E450A/E450AJP 8.5 in. (22 cm) E400A Narrow/E400AJP Narrow 5 in. (13 cm) Weight E400A/E400AJP 12,100 lb (5,488 kg) E400A Narrow/E400AJP Narrow 13,100 lb (5,942 kg) E450A 12,600 lb (5,715 kg) With Jib E300AJ 15,400 lb (6,985 kg) E450AJ 14,400 lb (6,532 kg) With JibPLUS E300AJP 15,800 lb (7,166 kg) E400AJP 13,700 lb (6,214 kg) E400AJP Narrow 14,900 lb (6,759 kg) Ground Bearing Pressure E300AJ/E300AJP 121 psi (8.47 kg/cm2) E400A/E400AJP 80 psi (5.6 kg/cm2) E400A Narrow/E400AJP Narrow 95 psi (6.7 kg/cm2) E450A 64 psi (4.48 kg/cm2) E450AJ 75 psi (5.25 kg/cm2) With JibPLUS E300AJP 130 psi (9.1 kg/cm2) E400AJP 74 psi (5.2 kg/cm2) E400AJP Narrow 185 psi (13.0 kg/cm2)

Form No.: SS-EB00MS-1202-10M Part No.: 3131119 R030905 Printed in USA

Chassis

Drive Speed E300AJ/E300AJP 3.0 mph (4.8 kmph) E400A Narrow/E400AJP Narrow 3.0 mph (4.8 kmph) E400A/E400AJP/E450A/E450AJ 3.2 mph (5.2 kmph) Gradeability E300AJ/E300AJP 25% E400A/E400AJP/E400A Narrow 30% E400AJP Narrow/E450A/E450AJ 30% Turning Radius (Inside) E300AJ/E300AJP 5 ft (1.52 m) E400A/E400AJP/E450A/E450AJ 2 ft (61 cm) E400A Narrow/E400AJP Narrow 2 ft 10 in. (86 cm) Turning Radius (Outside) E300AJ/E300AJP 10 ft 2 in. (3.1 m) E400A/E400AJP/E400A Narrow 10 ft 4 in. (3.15 m) E400AJP Narrow/E450A/E450AJ 10 ft 4 in. (3.15 m) Tire Size/Type E300AJ/E300AJP 7.5 x 12 Non-Marking E400A/E400AJP 240/55-17.5 pneumatic E450A/E450AJ 240/55-17.5 pneumatic Tire Size/Type (front) E400A Narrow/E400AJP Narrow 22 x 6 x 17.5 Non-Marking Tire Size/Type (back) E400A Narrow/E400AJP Narrow 22 x 7 x 12 Non-Marking

Power Source

Electrical System 48V DC Batteries 8 x 6V, 370 amp-hr Drive Motors Dual Electric Traction Brakes Automatic Spring Applied Multiple Disks Hydraulic Motor/Pump Permanent Magnet Motor/Gear Pump Hydraulic Reservoir E300AJ/E300AJP 3 gal. (11.4 L) E400A/E400AJP/E400A Narrow 4 gal. (15.2 L) E400AJP Narrow/E450A/E450AJ 4 gal. (15.2 L) Generator Set (Multi-Power Options) E400A/E400AJP/E400A Narrow E400AJP Narrow/E450A/E450AJ Fully Automatic, 45 Amp Kubota 6 hp Air-Cooled Engine Engine Fuel Tank E400A/E400AJP/E400A Narrow 4 gal. (15.2 L) E400AJP Narrow/E450A/E450AJ 4 gal. (15.2 L)

JLG Industries, Inc. 1 JLG Drive McConnellsburg, PA 17233-9533 Telephone 717-485-5161 Toll-free in US 877-JLG-LIFT Fax 717-485-6417 www.jlg.com An Oshkosh Corporation Company

Model

ES Series EL EC T R I C

S C I S SO R

L I F T S

Features Proportional Controls Industry Leading Duty Cycles Drywall Gate1 Battery Condition Indicator 110V-AC Receptacle in Platform Fold-Down Guard Rails2 Automatic Traction Control (ATC) 20 Amp Automatic SCR Charger Slide-Out Battery Trays All Motion Alarm Horn Hourmeter Manual Descent Pull Cable 36 in. (91 cm) Roll-Out Deck Extension3 50 in. (1.27 m) Roll-Out Deck Extension4 Moveable, Removable Platform Control Console with Rail Mounting Bracket Lanyard Attach Points Lubrication Free Scissor Arm Bushings Scissor Maintenance Prop Mechanized Pothole Protection Powder-Coated Nickel Plated Pins Machine Tie Downs Fork Lift Pockets, Lift from Side and Rear Four 6V, 220 Amp-Hour Deep Cycle Batteries Tilt Alarm and Light On-Board Diagnostics/Battery State-of-Charge LEDs 1. Not included on 1930ES. 2. Optional on 1930ES. 3. 1930ES, 2030ES, and 2630ES. 4. 2646ES and 3246ES.

Accessories & Options Spring-Loaded Gate Flashing Amber Beacon 245 Amp-Hour Batteries1 1,000W-AC Inverter Lifting Lugs UL® EE Rating2 Platform Padding Platform Padding with Proximity Switches Quik Welder Prep Package 1/2 in. Airline Nite Bright 220 Amp-Hour AGM Batteries Special Hydraulic Oils Accessory Packages: Electrician’s Package3 Plumber’s Package3 Plant Maintenance Package3 Panel Carrier Accessory1 Pipe Rack Accessory1 Quick Welder® Package JLG® Workstation 1. Not available on the 1930ES. 2. Not available with AGM Batteries. 3. Not available on 2030ES, 2630ES.

Cleaner Operation, Longer Runtime nly two hoses and four fittings mean improved reliability and reduced O service requirements n Double the duty cycles thanks to super-efficient electric drive n Q uieter operation for sound-sensitive areas and applications n

Higher Capacities and Larger Platforms olds up to 1,000 lb on the large 44 in. x 98.5 in. platform H Up to 250 lb capacity on the extension platform n Narrow models drive through doorways and tight aisles n W ide models provide more workspace with wider decks and longer platform extensions n n

Mobility and Versatility F ront-wheel drive and front-wheel steering offer tight turning circles Durable, non-skid aluminum deck n Optional Workstation in the Sky ® accessory packages enhance productivity n n

Model

EL EC T R I C

Specifications D

I F

H G

Dimensions

Platform Height–Elevated 1930ES 18 ft 9 in. (5.72 m) 2030ES 20 ft (6.10 m) 2630ES 25 ft 6 in. (7.77 m) 2646ES 26 ft (7.92 m) 3246ES 31 ft 9 in. (9.68 m) A. Platform Height–Lowered 1930ES 34 in. (0.86 m) 2030ES 43.5 in. (1.10 m) 2630ES 48.5 in. (1.23 m) 2646ES 49.5 in. (1.26 m) 3246ES 49.5 in. (1.26 m) B. Platform Railing Height 43.3 in. (1.10 m) C. Overall Height–Rails Lowered 1930ES N/A 2030ES 5 ft 11.5 in. (1.80 m) 2630ES 6 ft 4.5 in. (1.94 m) 2646ES/3246ES 6 ft 5.5 in. (1.97 m) D. Platform Size 1930ES 30 x 73.5 in. (0.76 x 1.87 m) 2030ES/2630ES 30 x 90.5 in. (0.76 x 2.3 m) 2646ES/3246ES 44 x 98.5 in. (1.12 x 2.5 m) E. Platform Extension 1930ES/2030ES/2630ES 35.5 in. (0.9 m) 2646ES/3246ES 50 in. (1.27 m)

F. Overall Width 1930ES/2030ES/2630ES 30 in. (96 cm) 2646ES/3246ES 46 in. (1.17 m) G. Overall Length 1930ES 6 ft 1.5 in. (1.87 m) 2030ES/2630ES 7 ft 6.5 in. (2.3 m) 2646ES/3246ES 8 ft 2.5 in (2.5 m) H. Wheelbase 1930ES 5 ft 3 in. (1.6 m) 2030ES/2630ES 6 ft 2 in. (1.88 m) 2646ES/3246ES 6 ft 10 in. (2.09 m) I. Ground Clearance 1930ES/2030ES/2630ES 3.5 in. (8.8 cm) 2646ES/3246ES 5 in. (12.7 cm) Platform Capacity 1930ES 500 lb (227 kg) 2030ES 800 lb (363 kg) 2630ES 500/800 lb (227/363 kg) 2646ES 1,000 lb (454 kg) 3246ES 700/1,000 lb (318/454 kg) Capacity on Platform Extension 250 lb (113 kg) Lift/Lower Time 1930ES 26/30 seconds 2030ES 28/40 seconds 2630ES 33/37 seconds 2646ES 41/50 seconds 3246ES 55/62 seconds Maximum Drive Height Fully Elevated Weight* 1930ES 2,685 lb (1,218 kg) 2030ES 3,830 lb (1,737 kg) 2630ES 4,815 lb (2,184 kg) 2646ES/ 3246ES 4,945 lb (2,243 lb) Ground Bearing Pressure 1930ES 109 psi (7.66 kg/cm2) 2030ES 81 psi (5.69 kg/cm2) 2630ES 90 psi (6.32 kg/cm2) 2646ES/ 3246ES 87 psi (6.11 kg/cm2)

Chassis

Drive Speed–Elevated 0.5 mph (0.8 km/h Drive Speed–Lowered 1930ES 3.0 mph (4.82 km/h) 2030ES/2630ES 2.75 mph (4.43 km/h) 2646ES/3246ES 2.50 mph (4.00 km/h) Gradeability 25% Turning Radius (Inside) Zero Turning Radius (Outside) 1930ES 69 in. (1.75 m) 2030ES/2630ES 81 in. (2.06 m) 2646ES/3246ES 95.1 in. (2.41 m) Tire Size/Type 1930ES 12.5 x 4 in. Non-Marking Solid 2030ES/2630ES/2646ES/3246ES 16 x 5 in. Non-Marking Solid Brakes Electric, Friction

Power Source Batteries Charger

Form No.: SS-ES-0110 Part No.: 3131580 Printed in USA

ES Series

S C I S SO R

L I F T S

Pump Fixed Displacement Gear Hydraulic Reservoir 1930ES/2030ES/2630ES 1.25 gal. (4.73 L) 2646ES/3246ES 1.7 gal. (6.4 L) Drive 24V Electric (8 hp) *Certain options or country standards will increase weight.

The JLG “1 & 5” Warranty JLG Industries, Inc. backs our products with our exclusive “1 & 5” Warranty. We provide coverage for one (1) full year, and cover all specified major structural components for five (5) years. These machines meet or exceed applicable OSHA Regulations in 29 CFR 1910.67, 29 CFR 1926.453, ANSI A92.6-2006 and CSA standard B354.4-02 as originally manufactured for intended applications. We reserve the right to make price, specification, and/or equipment changes without prior notification.

4 x 6V, 220 amp-hr 20 Amp Automatic JLG Industries, Inc. 1 JLG Drive McConnellsburg, PA 17233-9533 Telephone 717-485-5161 Toll-free in US 877-JLG-LIFT Fax 717-485-6417 www.jlg.com An Oshkosh Corporation Company

Model

LE Series

E L EC T R I C S C I S SO R L I F T

Features 65 x 115 in. (1.65 x 2.92 m) Work Platform Full Time ATC—JLG Automatic Traction Control System Oscillating Axle Proportional Direct DC Electric Drive Proportional Lift Up 110V-AC Receptacle in Platform 240/55-17.5 Foam-Filled Non-Marking Tires 8 x 6V, 370 amp-hr Batteries 3 ft Roll-Out Deck Extension On-Board Diagnostics with Common JLG Analyzer Forklift-Able Battery Compartments with Quick Disconnect Couplings Fold-Down Hand Rails Moveable, Removable Platform Console Box 23 Amp Automatic, SCR Battery Charger Battery Charge Indicator in Platform 3 Degree Tilt Indicator Light and Alarm All Motion Alarm Manual Descent Tie Down Lugs Hourmeter Horn

Accessories & Options 110V AC Power Pack (Generator) Flashing Amber Beacon Sand/Turf Tires Hydraulic Leveling Jacks Platform Work Lights QuikCharge GenSet All-Wheel Drive

Superior Performance On or Off Slab Rugged all-terrain tires and available all-wheel drive Full-time Automatic Traction Control and oscillating axle ■ Optional hydraulic leveling jacks for uneven terrain ■ ■

Power to Stay On the Job Longer Double the duty cycles of competitive electric scissor lifts Exclusive QuikCharge GenSet option provides automatic charging system for continuous operation ■ Provides better fuel efficiency to lower costs and increase uptime ■ ■

High Capacities and Cleaner Operation Holds up to 1,000 lb on the platform (Model 3369LE) and 250 lb on the platform extension ■ Zero emissions and quiet operation for sensitive indoor applications ■

Model

LE Series

E L EC T R I C S C I S SO R L I F T

Specifications

C. Overall Height–Rails Up 3369LE 9 ft (2.74 m) 4069LE 9 ft 2.5 in. (2.81 m) Overall Height–Rails Lowered 3369LE 6 ft 5 in. (1.96 m) 4069LE 6 ft 7 in. (2.0 m) D. Platform Size 65 x 115 in. (1.65 x 2.92 m) E. Platform Extension 3 ft (91 cm) F. Overall Width 5 ft 9 in. (1.75 m) G. Overall Length 10 ft 2 in. (3.1 m) H. Wheelbase 7 ft 6.5 in. (2.3 m) I. Ground Clearance 8 in. (20 cm) Platform Capacity 3369LE 1,000 lb (454 kg) 4069LE 800 lb (362 kg) Capacity on Platform Extension 250 lb (113 kg) Lift/Lower Time 3369LE 38/42 sec 4069LE 54/50 sec Maximum Drive Height 3369LE Full Height 4069LE 30 ft (9.14 m) Weight* 3369LE 9,760 lb (4,427 kg) 4069LE 10,560 lb (4,790 kg) Ground Bearing Pressure 3369LE 57 PSI (4.01 kg/cm2) 4069LE 61 PSI (4.29 kg/cm2)

Optional All-Wheel Drive Provides Superior Performance On or Off Slab

Chassis

Drive Speed–Elevated 0.4 mph (.64 kmph) Drive Speed–Lowered 3.0 mph (4.8 kmph) Gradeability (2WD/4WD) 35%/45% Turning Radius (Inside) 90 in. (2.29 m) Turning Radius (Outside) 186 in. (4.72 m) Tire Size/Type 240/55-17.5 Non-Marking Brakes Spring Applied Hydraulically Released Discs

Power Source Dimensions

A. Platform Height–Elevated 3369LE 33 ft (10.06 m) 4069LE 40 ft (12.19 m) Platform Height–Lowered 3369LE 5 ft 6.5 in. (1.69 m) 4069LE 5 ft 9 in. (1.75 m) B. Platform Railing Height 3 ft 7.5 in. (1.10 m)

Batteries 8 x 6V, 370 amp-hr Charger 21 Amp, Automatic SCR Charger Electric Pump Motor Series Wound Drive Motors Two 5.5 hp Shunt Wound Pump Single Section Gear Pump Hydraulic Reservoir 8.5 gal. (32.18 L) Generator Set (Multi-power Options) Fully Automatic, 45 Amp Kubota 6 hp Air-Cooled Engine Engine Fuel Tank 4 gal. (15.14 L)

The JLG “1 & 5” Warranty JLG Industries, Inc. backs its products with its exclusive “1 & 5” Warranty. We provide coverage on all products for one (1) full year, and cover all specified major structural components for five (5) years. Due to continuous product improvements, we reserve the right to make specification and/or equipment changes without prior notification. This machine meets or exceeds applicable OSHA Regulations in 29 CFR 1910.67, 29 CFR 1926.453, ANSI A92.6-2006, and CSA Standard CAN3-B354.2-M82, as originally manufactured for intended applications.

*Certain options or country standards will increase weight.

Form No.: SS-LE-504-10M Part No.: 3131502 R060706 Printed in USA

JLG Industries, Inc. 1 JLG Drive McConnellsburg, PA 17233-9533 Telephone 717-485-5161 Toll-free in US 877-JLG-LIFT Fax 717-485-6417 www.jlg.com An Oshkosh Truck Corporation Company

Model

600 Series t el es c o p i c B o o m L i f t s

Features Platform: 36 x 96 in. (0.91 x 2.44 m) SkyPower® Package Oscillating Axle Inward Swinging Gate Hydraulic Platform Rotator 110V AC Receptacle in the Platform 5 Degree Tilt Alarm/Indicator Light Swing-Out Engine Tray 12V DC Auxiliary Power Hourmeter Control ADE® System All Motion Alarm Proportional Controls Gull-Wing Hoods Operators Tool Tray Platform Console Machine Status Light Panel* Lifting/Tie Down Lugs Engine Distress Warning/Shutdown— Selectable via JLG Analyzer * Provides indicator lights at platform control console for system distress, fuel level, low fuel, 5 degree tilt light and foot switch status.

Accessories & Options 36 x 72 in. (0.91 x 1.83 m) Platform Fall Arrest Platform Mesh to Top Rail Bolt-on Aluminum 6 ft Mesh to Top Rail Bolt-on Aluminum 8 ft Soft Touch System Foam-Filled Tires 2500W Generator Tow Package Exhaust Purifier Muffler 43.5 lb (19.7 kg) Propane Tank Cold Weather Start Kit (GM) Cold Weather Start Kit (Deutz & CAT) Hostile Environment Kit Light Package Platform Worklights Flashing Amber Beacon Semi-Track Arctic Package Accessory Packages: SkyWelder® SkyGlazier® Nite Bright® SkyCutter® Pipe Rack SkyAir®

Largest Working Range in its Class n n

5 6 ft 9 in. (17.3 m) of horizontal outreach for improved access Versatile articulating jib provides a wider range of motion

Easier Maintenance, Reduced Costs wing-out engine tray allows for faster and easier access S for routine maintenance n E xclusive Advanced Design Electronics (Control ADE ® ) System provides smoother machine functions, increased fuel efficiency and reduced emissions n

Higher Capacity and Improved Performance n n

I ndustry’s highest platform capacity of 1,000 lb (454 kg) 4 5% gradeability and oscillating axle for improved traction

Model

600 Series t e l e s c o p i c B o o m l i f t s

Reach

Specifications 600S 70 ft (21.34 m)

500 lb (227 kg)

60 ft (18.29 m)

1000 lb (454 kg)

50 ft (15.24 m) 40 ft (12.19 m) 30 ft (9.14 m) 20 ft (6.10 m)

0 ft (0 m)

60 ft 3 in. (18.36 m) 66 ft 8 in. (20.32 m) 49 ft 6 in. (15.09 m) 56 ft 9 in. (17.3 m) 360° Continuous 1,000 lb (454 kg)

Dual Fuel Engine, GM Vortec 3000 MPFI Diesel Engine, Deutz D2011L04 Diesel Engine, Caterpillar 3044C Fuel Tank Capacity Hydraulic Reservoir Auxiliary Power

82 hp (61 kW) 49 hp (36.4 kW) 63 hp (47 kW) 40 gal (151 L) 32 gal (121 L) 12V DC

500 lb (227 kg) 160° Hydraulic 180° Hydraulic

A. Platform Size 36 x 96 in. (0.91 x 2.44 m) B. Overall Width 7 ft 11 in. (2.41 m) C. Tailswing (working condition) 3 ft 9 in. (1.14 m) D. Stowed Height 8 ft 5 in. (2.57 m) E. Stowed Length 600S 27 ft 11 in. (8.51) 660SJ 33 ft 6 in. (10.21 m) F. Wheelbase 8 ft 1 in. (2.46 m) G. Ground Clearance 12 in. (30 cm) 1 Weight 600S 22,750 lb (10,319 kg) 660SJ 27,600 lb (12,519 kg) Max. Ground Bearing Pressure 600S 67 psi (4.7 kg/cm2) 660SJ 75 psi (5.27 kg/cm2)

Use This Color 0 ft (0 m)

10 ft 20 ft 30 ft 40 ft 50 ft 60 ft (3.05 m) (6.10 m) (9.14 m) (12.19 m) (15.24 m) (18.29 m)

660SJ 70 ft (21.34 m)

500 lb (227 kg)

60 ft (18.29 m)

Use This Color

50 ft (15.24 m) 40 ft (12.19 m)

Use This for Tan Bkgd

1. Certain options or country standards increase weight

Chassis

30 ft (9.14 m) 20 ft (6.10 m) 10 ft (3.05 m) 0 ft (0 m) -10 ft (-3.05 m)

Power Source

Dimensions

10 ft (3.05 m)

-10 ft (-3.05 m)

Platform Height 600S 660SJ Horizontal Outreach 600S 660SJ Swing Platform Capacity— Restricted (600S Only) Platform Capacity— Unrestricted Platform Rotator 600S 660SJ

0 ft (0 m)

10 ft 20 ft 30 ft 40 ft 50 ft 60 ft (3.05 m) (6.10 m) (9.14 m) (12.19 m) (15.24 m) (18.29 m)

Drive Speed 2WD 4.25 mph (6.8 kmph) Drive Speed 4WD 4.25 mph (6.8 kmph) Gradeability 2WD 30% Gradeability 4WD 45% Tires 600S & 660SJ 39 x 15-225 Lug Tread Axle Oscillation 8 in. (20 cm) Turning Radius, (Inside/Outside) 2WS 7 ft 7.5 in./17 ft 6 in. (3.45 m/5.41 m) 4WS 4 ft 4.5 in./11 ft 6.5 in. (1.65 m/3.45 m)

Form No.: SS-600S-0204-15M Part No.: 3131028 R051008 Printed in USA

The JLG “1 & 5” Warranty

JLG Industries, Inc. backs our products with our exclusive “1 & 5” Warranty. We provide coverage for one (1) full year, and cover all specified major structural components for five (5) years. These machines meet or exceed applicable OSHA Regulations in 29 CFR 1910.67, 29 CFR 1926.453, ANSI A92.5-2006 and CSA standard B354.4-02 as originally manufactured for intended applications. We reserve the right to make price, specification, and/or equipment changes without prior notification.

JLG Industries, Inc. 1 JLG Drive McConnellsburg, PA 17233-9533 Telephone 717-485-5161 Toll-free in US 877-JLG-LIFT Fax 717-485-6417 www.jlg.com An Oshkosh Corporation Company

Model

1230ES M AS T

L I F T

Features Industry leading duty cycles Controls and electrical system common with ES Series scissor lift Joystick with fully proportional lift and drive All-steel platform deck and rails Saloon-style entry gate Standard 110 V AC wiring to platform Corner tool tray Automatic traction control Steel swing-out battery doors with heavy duty hinges Mechanical Pothole Protection System All motion alarm Tilt alarm and light Battery condition indicator Horn Hourmeter Powder paint coating Lanyard attachment points Integrated lifting and tie-down points Machine can be lifted by forks from either side Pressure check port

Accessories & Options Flashing amber beacon 1,000W – AC Inverter/charger

Ease of Maintenance, Reduced Cost Maintenance free elevating mast design — no chains, cables or rollers to grease or adjust ■ Only four hoses — less to maintain, minimizes leak potential ■

Compact and Maneuverable in Tight Spaces Saloon-style swing gate for ease of entry and exit.

All-steel swing-out battery doors with heavy-duty hinges.

Compact dimensions and low overall weight Fits on most freight elevators ■ Tight turning radius ■ Direct Electric front wheel drive ■ Ground level entry ■ ■

Model

1230ES

M AS T

Specifications

L I F T

Dimensions

A.Platform Height – Elevated 12 ft (3.66 m) B.Platform Height – Lowered 1 ft 10 in. (0.56 m) C.Platform Rail Height 3 ft 7 in. (1.10 m) D.Overall Height 5 ft 5 in (1.66 m) E.Platform Size 27 x 49.5 in. (0.68 x 1.25 m) F.Overall Length 4 ft 6 in. (1.36 m) G.Overall Width 2 ft 6 in. (0.76 m) H.Wheelbase 3 ft 5 in. (1.04 m) I.Ground Clearance 2.6 in. (6.6 cm) Platform Capacity 500 lb (227 kg) Lift/Lower Time 12 / 12 sec. Maximum Drive Height Full Height Weight 1,740 lb (790 kg)

Chassis

Drive Speed Lowered 3 mph (4.8 kmph) Drive Speed Elevated 0.5 mph (0.8 kmph) Gradeability 25% Turning Radius – Inside 5 in. (13 cm) Turning Radius – Outside 4 ft 10 in. (1.46 m) Tire Size/Type 318 x 100 Non-Marking Solid Brakes (On Drive Wheels) Electric, Friction

Power System Charger

Batteries Drive Hydraulic Reservoir

20 Amp Automatic (120V/240V – 50/60 HZ) 4 x 6V 220 amp-hr 24V Electric, 8 hp (6kW) 1.88 gal. (7.1 L)

The JLG “1 & 5” Warranty

JLG Industries, Inc. backs our ES Series Mast Lifts with our exclusive “1 & 5” Warranty. We provide coverage for one (1) full year, and cover all specified major structural components for five (5) years. These machines meet or exceed applicable OSHA Regulations in 29 CFR 1910.67, 29 CFR 1926.453, ANSI A92.6-2006 and CSA standard CSA-B354.2-01 as originally manufactured for intended applications. We reserve the right to make price, specification, and/ or equipment changes without prior notification.

Form No.: 1230ES-0107-10M Part No.: 3131309 R070802 Printed in USA

JLG Industries, Inc. 1 JLG Drive McConnellsburg, PA 17233-9533 Telephone 717-485-5161 Toll-free in US 877-JLG-LIFT Fax 717-485-6417 www.jlg.com An Oshkosh Corporation Company

Model

800 Series T el es c o p i c B o o m L i f t s

Features 6 ft (1.83 m) Articulating Jib (860SJ Only) Platform: 36 x 96 in. (0.91 x 2.44 m) Side Entry Inward Swinging Gate Dual-Rated Capacities SkyPower® Package Oscillating Axle Hydraulic Platform Rotator 110V AC Receptacle in the Platform 5 Degree Tilt Alarm/Indicator Light Swing-Out Engine Tray 12V DC Auxiliary Power Hourmeter Fuel Gauge Control ADE® System All Motion Alarm Proportional Controls Gull-Wing Hoods Hydrostatic Drive Operators Tool Tray Platform Console Machine Status Light Panel* Lifting/Tie Down Lugs Engine Distress Warning/Shutdown— Selectable via JLG Analyzer 15-625 Rim Protector Lug Tread Tires Glow Plugs (Diesel Engines) * Provides indicator lights at platform control console for system distress, fuel level, low fuel, 5 degree tilt light and foot switch status.

Accessories & Options Platform: 36 x 72 in. (0.91 x 1.83 m) Fall Arrrest Platform (Requires Foam Filled Tires) Mesh to Top Rail Light Package1 Flashing Amber Beacon 15-625 Foam Filled Tires 18-625 Foam Filled Tires Soft-Touch System Catalytic Muffler Cold Weather Start Kit 2 Hostile Environment Kit 3 Arctic Package4 Platform Worklights Tow Package Special Hydraulic Oils (Consult Factory) Accessory Packages: SkyWelder® SkyGlazier® Nite Bright® SkyCutter® Pipe Rack SkyAir®

1. Includes platform mounted work lights and drive/backup lights. 2. Engine block heater, battery heater and oil tank heater. 3. Includes console cover, boom wipers and cylinder bellows. 4. Includes arctic hydraulic hoses (drive and steer only and main boom cable, arctic hydraulic oil, extreme cold engine oil, anti-freeze (CAT only), fuel conditioner, engine block heater, battery blanket, glow plugs, hydraulic tank heater and oversized foot switch.

Optimum Performance, Increased Productivity o from ground to 80 ft (24.38 m) in less than 67 seconds— G 40% faster than competitive models n Revolutionary Workstation in the Sky ® accessory packages enhance the work environment and increase productivity n

Easier Maintenance, Reduced Costs S wing-out engine tray allows for faster and easier access for routine maintenance n E xclusive Advanced Design Electronics (Control ADE ® ) System provides smoother machine functions, increased fuel efficiency and reduced emissions n

Higher Capacity and Improved Performance n n

ual-rated platform capacities up to 1,000 lb (454 kg) D 4 5% gradeability and oscillating axle for improved traction

Model

800 Series T el es c o p i c B o o m l i f t s

Reach

Specifications

Platform Height 800S 860SJ Horizontal Outreach 800S 860SJ Swing Platform Capacity— Restricted (800S) Restricted (860SJ) Platform Capacity— Unrestricted Platform Rotator Jib Range of Articulation 860SJ

800S 90 ft.

27.43 m

80 ft.

24.38 m

70 ft.

21.34 m

60 ft.

18.29 m

50 ft.

15.24 m

40 ft.

12.19 m

30 ft.

9.14 m

Power Source

80 ft (24.38 m) 86 ft (26.21 m) 71 ft (21.64 m) 75 ft (22.86 m) 360° Continuous 1,000 lb (454 kg) 750 lb (340 kg) 500 lb (227 kg) 180° Hydraulic

Dual Fuel Engine, GM Vortec 3000 MPFI 82 hp (61 kW) Diesel Engine, Deutz D2011L04 with EGR 64 hp (47 kW) Diesel Engine, Caterpillar C3.4 63.3 hp (47.2 kW) Fuel Tank Capacity 31 gal (117.3 L) Hydraulic Reservoir 48 gal (181.7 L) Auxiliary Power 12V DC

800S

130° (+70, -60)

Dimensions

20 ft.

6.10 m

10 ft.

3.05 m

10 ft.

3.05 m

20 ft.

6.10 m

30 ft. 40 ft.

50 ft.

60 ft.

70 ft.

80 ft.

9.14 m 12.19 m 15.24 m 18.29 m 21.34 m 24.38 m

860SJ 90 ft.

27.43 m

80 ft.

24.38 m

70 ft.

21.34 m

60 ft.

18.29 m

50 ft.

15.24 m

40 ft.

12.19 m

30 ft.

A. Platform Size 36 x 96 in. (0.91 x 2.44 m) B. Overall Width 8 ft 2 in. (2.49 m) C. Tailswing (working condition) 4 ft 8 in. (1.42 m) D. Stowed Height 800S 9 ft 11 in. (3.02 m) 860SJ 10 ft (3.05 m) E. Stowed Length 800S 37 ft 3 in. (11.35 m) 860SJ 40 ft (12.19 m) F. Wheelbase 10 ft (3.05 m) G. Ground Clearance 12 in. (30 cm) Weight1 800S 33,200 lb (15,060 kg) 860SJ 36,400 lb (16,511 kg) Max. Ground Bearing Pressure 800S 72 psi (5.06 kg/cm2) 860SJ 81 psi (5.69 kg/cm2)

Chassis

9.14 m

20 ft.

6.10 m

10 ft.

3.05 m

10 ft.

3.05 m

20 ft.

6.10 m

30 ft. 40 ft.

50 ft.

60 ft.

70 ft.

80 ft.

9.14 m 12.19 m 15.24 m 18.29 m 21.34 m 24.38 m

Drive Speed 2WD Drive Speed 4WD Gradeability 2WD Gradeability 4WD Tires Turning Radius Inside Outside

3.5 mph (5.6 kmph) 3.5 mph (5.6 kmph) 30% 45% 15.625 Pneumatic 12 ft (3.66 m) 22 ft 6 in. (6.86 m)

1. Certain options or country standards increase weight.

Form No.: SS-800S-0906-15M Part No.: 3131024 R110808 Printed in USA

800SJ

The JLG “1 & 5” Warranty JLG Industries, Inc. backs our products with our exclusive “1 & 5” Warranty. We provide coverage for one (1) full year, and cover all specified major structural components for five (5) years. These machines meet or exceed applicable OSHA Regulations in 29 CFR 1910.67, 29 CFR 1926.453, ANSI A92.5-2006 and CSA standard B354.4-02 as originally manufactured for intended applications. We reserve the right to make price, specification, and/or equipment changes without prior notification.

JLG Industries, Inc. 1 JLG Drive McConnellsburg, PA 17233-9533 Telephone 717-485-5161 Toll-free in US 877-JLG-LIFT Fax 717-485-6417 www.jlg.com An Oshkosh Corporation Company

Ed Nakashian

Vice President of Sales & Operations T: 1-800-237-9195 C: 917-693-3252 E: enakashian@altitudeequipmentrentals.com

120 Broadway New York, NY 10271 F: 212-748-5027