Regupol速 underscreed range High performance acoustic screed isolation
Technical support With a fully trained technical services team, RAME can provide free support at every stage of a project – from specification through to installation.
Sustainable systems All products in the RAME portfolio are carefully developed based on environmental as well as acoustic performance – delivering access to high quality yet sustainable systems.
Fully stocked warehouses
Through fully stocked regional warehousing facilities, RAME ensures the cost effective, efficient and reliable delivery of all Regupol® products, across the breadth of the Middle East.
Regupol® underscreed range Flexible & sustainable acoustic isolation The Regupol® range of acoustic isolation materials offers the broadest choice of underscreed materials in the Middle East. Delivering various levels of impact sound insulation and load bearing capacities, Regupol® underscreed products are guaranteed to deliver the most cost effective yet high performing system for any development. Offered exclusively in the Middle East by Regupol Acoustics Middle East (RAME), the underscreed range includes Regupol® 7210C, Regupol® E48, Regupol® 6010BA and Regupol® 6010SH. Manufactured from fully recyclable materials and without blowing agents, these systems meet the LEED (Leadership in Energy and Environmental Design) requirements for VOC, recyclability and sustainability. Compatible with all types of subfloors and screeds, Regupol® underscreed systems are a flexible specification and have been independently proven to achieve superior impact sound control, even in the most demanding of applications. RAME holds Regupol® products as stock in regional warehouses, enabling the efficient delivery and consistent supply of all systems in the underscreed range.
Simple to install Regupol® underscreed systems are quick and easy to install, with comprehensive installation guidelines available on request. It is important that prior to installing Regupol® materials, base floors are clean, flat and dry. The materials should also be unwound and left for a minimum 8 hours or ideally overnight at the place where they are to be installed, to allow for any potential shrinkage. The materials should be cut to size with a sharp craft knife and straight edge. Joints should be taped with Regupol® tape. Regupol® E48 and Regupol® 6010BA should be installed dimple side down. For all Regupol® underscreed materials, RAME provides free technical guidance and on-site support during the installation process.
Cost effective screed isolation Regupol® 7210C Regupol® 7210C is a cost effective rubber-bound product, manufactured from recycled materials. Compatible with all types of floor screed, this high performing isolation solution delivers superior impact and airborne performance. Regupol® 7210C is quick and easy to install, and because separate perimeter strips are not required, using this system helps ensure an efficient and reliable installation.
Applications
Installation
Regupol 7210C is designed for applications where superior and cost effective impact sound control is required. It is particularly suited to the following developments: ®
• • • •
Apartments Hotels Retail Education
1 2
3 4 5
Features & benefits
6
• Excellent impact and airborne performance • Offers long term performance without collapse or “bottoming” out under high point loads • Quick and easy to install with no need for separate perimeter strips • Minimises construction heights • Supplied in easy to handle sheets • Mildew and moisture proof • Zero global warming potential (GWP) and zero ozone depletion potential (ODP)
7
For example purposes only
1
3
5
6
8
Specification
* DPM overlap to be minimum 100mm
Physical Information Sheet length Sheet width Material thickness
1 65mm sand cement screed or minimum 40mm proprietary screed 2 Taped joint* 3 0.2mm waterproof membrane 4 Joint detail 5 Regupol® 7210C 5mm layer 6 Concrete slab 7 Perimeter detail 8 Acoustic cavity closer 9 Regupol® hi-tack tape
For example purposes only
2250mm 1150mm 5mm
4
Joint Detail (overlapped) 9
7 Perimeter Detail
Technical Information Density
720kg/m3
5
Tensile strength (DIN 53571)
approx 0.5N/mm2
For example purposes only
Thermal conductivity
approx 0.14W/mK
Elongation at break
approx. 75%
Temperature resistance
-40ºC to +110ºC
Airborne sound insulation (DnT,w + Ctr)
49dB
Impact sound insulation (L’nT,w (Ci))
46dB
ǵLW (impact improvement)
20dB (BS EN ISO 140-8:1998)
4
5
6
Alternative Joint Detail (butted) 9
1
3
5
6
For example purposes only 5
5
6
For example purposes only
4
Enhanced isolation performance Regupol® E48 Regupol® E48 is a recycled tyre crumb product designed to isolate screeds from the main structure of the building, reducing impact energy generated by general footfall. With a dimpled surface on one side, which increases air movement and dissipates energy in channels, Regupol® E48 offers enhanced isolation performance and delivers impact sound insulation of 47dB, even under heavy loads.
Applications
Installation
Regupol E48 has been developed to offer enhanced isolation and impact sound performance in the following areas: ®
• • • • •
Apartments Hotels Schools Hospitals Retail
1 2 3 4 5
Features & benefits
6
• Excellent impact and airborne performance • Offers long term performance without collapse or “bottoming” out under high point loads • Resistant to ageing and deformation • Quick and easy to install with no need for separate perimeter strips • Minimises construction heights • Mildew and moisture proof • Zero global warming potential (GWP) and zero ozone depletion potential (ODP)
7
For example purposes only
1
3
5
6
8
Specification Physical Information For example purposes only
Roll width Roll lengths Material thickness
1 65mm sand cement screed or minimum 40mm proprietary screed 2 Taped joint* 3 0.2mm waterproof membrane 4 Joint detail 5 Regupol® E48 8mm layer 6 Concrete slab 7 Perimeter detail 8 Acoustic cavity closer 9 Regupol® hi-tack tape * DPM overlap to be minimum 100mm
1.15m 13m 8mm nominal (dimpled surface on one side) 4
Technical Information
Joint Detail (overlapped) 9
7 Perimeter Detail
Density
approx 600kg/m3
Tensile strength (DIN 53571)
approx 0.5N/mm2
Thermal conductivity
approx 0.14W/mK
Elongation at break
approx 47%
Mean Value of Dynamic Stiffness
47MN/m3
Maximum load bearing capacity
3000kg/m2 (30kN/m2)
Temperature resistance
-40ºC to +110ºC
Airborne sound insulation (DnT,w + Ctr)
49dB
Impact sound insulation (L’nT,w (Ci))
47dB
ǵLW (impact improvement)
20dB (BS EN ISO 140-8:1998)
5
5
6
For example purposes only
4
Alternative Joint Detail (butted) 9
1
3
5
6
For example purposes only 5
5
6
For example purposes only
Important Note: Regupol® E48 must be installed dimple side down.
5
High load bearing isolation Regupol® 6010BA Manufactured from recycled tyre crumb, Regupol® 6010BA is a high load bearing screed isolation solution. Delivering effective isolation and impact sound insulation, even under heavy loads, Regupol® 6010BA is often the preferred choice for premium developments and those where superior acoustic performance is critical.
Applications Regupol® 6010BA delivers a high end isolation solution for prestigious developments and areas where heavy loads are apparent. These include: • • • • • • • • •
Luxury apartments Penthouses Hotels Cinemas/Theatres Schools Hospitals Libraries Retail Gymnasiums
1 2 3 4
5 6 7
For example purposes only
Features & benefits • • • • • •
Excellent impact and airborne performance Minimal creep, even under high loads Resistant to ageing and deformation Quick and easy to install Mildew and moisture proof Zero global warming potential (GWP) and zero ozone depletion potential (ODP)
1
3
5
10 11
6
8
Specification
1 65mm sand cement screed 2 Taped joint* 3 0.2mm waterproof membrane 4 Joint detail (butted only) 5 Regupol® 6010BA 17mm layer 6 Concrete slab 7 Perimeter detail 8 Acoustic cavity closer 9 Regupol® hi-tack tape 10 Acoustic sealant 11 Perimeter edge strip
For example purposes only
* DPM overlap to be minimum 100mm
Physical Information Roll width Roll length Material thickness
1.25m 10m 17mm nominal (dimpled surface on one side)
7 Perimeter Detail 4
9
Technical Information Mean value of dynamic stiffness
Joint Detail (butted)
10
19MN/m3 (DIN EN 29052-1)
11
3
Density
590kg/m
Tensile strength (DIN 53571)
approx 0.3N/mm2
Thermal conductivity
approx 0.14W/mK
Elongation at break
approx 60%
5
5
6
For example purposes only
2
1
2
Maximum load bearing capacity
5000kg/m (50kN/m )
Temperature resistance
-40ºC to +110ºC
Airborne sound insulation (DnT,w + Ctr)
49dB
Impact sound insulation (L’nT,w (Ci))
38dB
ǵLW (impact improvement)
43dB (BS EN ISO 140-8:1998)
3
5
6
For example purposes only
Installation
Important Note: Regupol® 6010BA must be installed dimple side down.
6
High performance screed isolation Regupol® 6010SH A recycled tyre crumb product, Regupol® 6010SH has been specifically developed for heavy load bearing areas where acoustic performance is critical. A sustainable and high performing screed isolation solution, Regupol® 6010SH delivers the greatest load bearing capacity in the RAME underscreed range.
Applications
Installation
Designed for a wide range of high performance isolation applications, Regupol® 6010SH is particularly suited to heavily loaded areas in: • • • • • • • •
Luxury apartments Penthouses Hotels Schools Hospitals Libraries Retail Music studios
1 2 3 4
5 6 7
Features & benefits
For example purposes only
• Excellent impact and airborne performance • Offers long term performance without collapse or “bottoming” out under high point loads • Resistant to ageing and deformation • Quick and easy to install • High quality and exact material thickness guaranteed • Mildew and moisture proof • Zero global warming potential (GWP) and zero ozone depletion potential (ODP)
1
3
1 65mm sand cement screed 2 Taped joint* 3 0.2mm waterproof membrane 4 Joint detail (butted only) 5 Regupol® 6010SH 10mm or 15mm layer 6 Concrete slab 7 Perimeter detail 8 Acoustic cavity closer 9 Regupol® hi-tack tape 10 Acoustic sealant 11 Perimeter edge strip
5
10 11
6
8
For example purposes only
Specification * DPM overlap to be minimum 100mm
Physical Information Roll width Roll length Material thickness
7 Perimeter Detail
1.25m 10m 10mm & 15mm nominal
4
Joint Detail (butted) 9
10 11
Technical Information
5
Mean value of dynamic stiffness
28.8MN/m3 (DIN EN 29052-1)
Density
595kg/m3
Tensile strength (DIN 53571)
approx 0.40N/mm2
Thermal conductivity
approx 0.14W/mK
Elongation at break
approx 70%
Maximum load bearing capacity
10000kg/m2 (100kN/m2)
Temperature resistance
-40ºC to +110ºC
ǵLW (impact improvement)
30dB (BS EN ISO 140-8:1998)
5
6
For example purposes only
1
7
3
5
6
call
+971-4-3233493 www.regupolacousticsmiddleeast.com
Regupol Acoustics Middle East (RAME) is the Middle East arm of market-leading Regupol速 manufacturer, BSW. Providing exclusive access to the full range of Regupol速 impact sound systems, RAME is setting the standard for sound control in the Middle East. From specification through to project completion, RAME has a fully trained technical team able to provide free advice and on-site support as well as guidance during installation. This combined product and service offering has led to Regupol速 being used on a number of high profile projects, including Dubai Healthcare City and the Marina Hotel, Abu Dhabi. For further information and advice, please contact the RAME technical sales team.
Regupol Acoustics Middle East FZE P.O. Box 125279, Dubai, UAE Phone: +971-4-3233493 Fax: +971-4-3406295 info@regupolacousticsmiddleeast.com Regupol速 is an official trademark of BSW