MATERIALS FOR K6 CM OR HP INCHES LONG NECKLACE EXCEPT THE CLASP
T A T 8 mm round beads T KG pcs T B T RounDuo Pmm beads T KP pcs T C T HHLO seed beads T about HO gr T D T SuperDuo GIPxPmm T 66 pcs T E T Rizo beads T KK pcs jumpring or splitring T G pcs clasp T H pcs Fireline braided Nylon thread OIHGmm
Repeat steps from figIG and figIK figIH
figIG
figIX
figIP
figI6
figI7
figIK
fig.1 Pick up 1B and 5C, slide them down, leaving about 15cm or 5 inches tail of thread.
1
Pass through first taken B in same hole and in same direction and through next closest 3C. Pull tight.
2
Take 2C,1B, 2C, slide them down and pass in same direction through middle C (third one) from previous step. Pull tight.
3
Pass through next closest 2C. Pull tight.
4
fig.2 Take 2D and pass through free hole of same B.Pull tight.
5
Take 5C and pass through same hole of same B in same direction. Pull tight.
6
7
Pass through next 3C.
fig.3
Take 2C,1B, 2C, slide them down and pass in same direction through middle C (third one) from previous step. Pull tight.
8
Pass through next closest 2C. Pull tight.
9
From now on, repeat steps from fig.2 and fig.3 till you reach needed length.
fif.4
Once you've added your last B bead, take 2C and stitch in free hole of same B. Pull tight.
10
Take 5C and pass through same hole in same direction. Pull tight.
11
Pass through next closest 3C.
12
Take 5C and stitch in middle C Sthird one, from previous step in same direction. Pull tight. In this circle youbll attach your clasp with jumpring or splitring.
13
Now you must lead your thread to exit from first D bead. So, pass through all C beads toward it.
14
15
16
fig.5
Take 1C and stitch in next D.
17
Pass through free hole of same D in opposite direction. Pull tight.
18
Take 1C, 1E, 1C and pass through free hole of next D.
19
Pass through other hole of same D in opposite direction and through next C and D.
20
Pass through next 4C and first D. Repeat these 5 steps till the end of this row.
21
When you reach your last B, finish the row as you did on its other side.
22
23 24
25
Once you've added the loop for your clasp , you must lead your thread to exit from closest hole of first B. That's why pass through next 2C and...
26
...go up through closest hole of the B.
27
fig.6
28
Take 3C and stitch in next closest 4C.
Take 6C and slide them down.
29
Count backwards 3 C and stitch in fourth one, towards the B bead. Pull tight.
30
31
Take 2C and pass through next closest 4C. Pull tight. Repeat these steps until you form a pico over every B except the last one.
32
When you reach the last B, take 3C and stitch in next 2C.
33
Pass through next closest C...
and through next 2C as well.
34
Go up through first hole of B.
35
Now you must lead the thread to exit from tip C of first pico, so pass through next closest 5C....
36
and also through next 5C .
37
Go up through next closest C.
38
and through next 2C as well
39
fig.7
Take 1A and stitch in the tip C of next closest pico. Repeat this until you add an A between all picos of this row. Hide and trim your threads. All you have to do now is to attach your clasp, using a jumpring or splitring.
40