List of chemicals/products used on site PRODUCT NAME: Wabo FlameGuard II Blanket Chemical Family: Refractory Fiber Link to MSDS:https://wbacorp.com/public/userfiles/WaboFlameGuardIIBlanket_MSDS.pdf
QA/QC PLAN
Product name: Sikaflex® ‐ 1A
REVISED 10-6-20
Link to MSDS: https://usa.sarnafil.sika.com/downloads/repository/submittal/productdata/Sikaflex%C2%AE1A.pdf
Skanska/Balfour Beatty Project: Microsoft Parking Garage 079 50 00 – Expansion / Seismic Joint Covers
3902 West Valley Hwy. N. Suite 500, Auburn, WA 98001 ~ PH: 253-334-2740 ~ FAX: 888-229-8042
Microsoft Campus Modernization Parking Facility Redmond, WA
Section 079500 Expansion and Seismic Joint Cover Systems
QA/QC Plan A. Manufacturers: Obtain each type of seismic joint assembly from a single manufacturer. One manufacturer may be used for exterior joints and a different manufacturer may be used for interior joints. B.
Installer: A firm which is acceptable to manufacturer of seismic joint units, and has experience in installation of units similar to units indicated.
C.
Single Source: Provide materials from a single manufacturer for exterior expansion joint assemblies.
D.
Fire Performance: Where indicated, provide seismic joint assemblies with joint cycling requirements per ASTM F1399. 1.
Surface Burning Characteristics for Fiberglass Composites (Interior Applications): UL Class 1 per UL 723 (ASTM E84).
E.
Pre-Installation Conference: Schedule a job conference to review the work prior to scheduled commencement of work on the actual building in accordance with Section 013100 – Project management and Coordination. Conference shall be attended by Installer; manufacturer’s representative; Owner’s Representative, Architect and other representatives directly concerned with performance of the Work. The following major considerations shall be reviewed at conference: 1.
Review system requirements, including shop drawings, specifications, installation instructions and warranty requirements. Should any discrepancies arise, they shall be reviewed and resolved.
2.
Review trade related schedules.
3902 West Valley Hwy. N. Suite 500, Auburn, WA 98001 ~ PH: 253-334-2740 ~ FAX: 888-229-8042
F. Prior to installation; 1. Before beginning installation of these joint covers, review the architectural drawings and approved CS shop drawings to familiarize yourself with the joint cover models and locations. 2. Check all of the joint cover components to confirm that the correct joint cover model and size have been received. Also check for materials that may have been damaged during shipping. Report all incorrect and/or damaged components to CS at 800-233-8493. 3. Joint covers must be securely mounted to structurally sound substrates. Repair all cracks (By SBB) or spalled areas of the concrete deck. The mounting surface must be clean and free from any loose dust, dirt, debris and oils. 4. All materials should be arranged in the order that they are to be installed. All hardware required for each portion of the work should be placed with the appropriate materials .Review all Approved Shop Drawings and this Document to familiarize yourself with all the details and components of this assembly .Prior to the commencement of Installation, all materials MUST be inspected for Damage. Any damage must be reported to CONSTRUCTION SPECIALTIES, INC., as soon as possible, so that replacement materials may be furnished without delay. All work must be completed as per Architect's Approved "Shop Drawings", and in accordance with these Installation Instructions. When installation is complete, all materials must be protected from damage until the Architect's FINAL INSPECTION G. Post Installation QAQC Checklist; 1. Ensure all installation requirements were met and are satisfactory. In order to ensure all installed products, meet quality guidelines, foreman must perform QAQC Checklist found on page 4 and 5 of the Quality Plan. 2. QAQC Checklist must be submitted to General Contractor after every shift. The QAQC must include all models installed.
3902 West Valley Hwy. N. Suite 500, Auburn, WA 98001 ~ PH: 253-334-2740 ~ FAX: 888-229-8042
Model
Type
Floor Fastener
Wall Fastener
Centers
Max Butt-seam Width
Wall Flange Caulk (Y/N)
Notes
SMPW
floor to wall
1/4" x 2" Flat head 3/16"x1-1/2" Split drive dowel
3/8"x2-1/2" screw bolt
18" O.C.
3/16"
Y
SMP
floor to floor
1/4"x2" Flat head
NA
18" O.C.
3/16"
N
PCW
floor to wall
NA
3/8"x2-1/2" screw bolt
18" O.C.
3/16"
Y
PCW 17" or greater
floor to wall
NA
1/4"x2" Hilti KB3
18" O.C.
3/16"
N
SFW
wall to wall
NA
3/16"x1-3/4" self tapping flat head
18" O.C.
3/16"
N
SCW
wall to wall
NA
3/16"x1-3/4" self tapping flat head
18" O.C.
3/16"
N
5/16- 8x3-1/2" bolt to attached cover plate to turnbar
VF
wall to wall
NA
NA
NA
3/16"
Y
Pre-compressed expanding foam installed with silicone caulking
FB17
floor to floor
3/16"x1-1/2" self tapping flat head
3/8"x2" screw bolt
18" O.C.
3/16"
N
3/8- 16x6" bolt to attachcover plate to turnbar (12" O.C.)
3902 West Valley Hwy. N. Suite 500, Auburn, WA 98001 ~ PH: 253-334-2740 ~ FAX: 888-229-8042
3902 West Valley Hwy. N. Suite 500, Auburn, WA 98001 ~ PH: 253-334-2740 ~ FAX: 888-229-8042