2021 NSP Foil Catalog

SUP

2021 DEALER GUIDE

Photographer : Sam Thom

Rider : Shaan Miller

Location : New Zealand

Board : Surf Foil

FOILING

<

1

DEALER GUIDE 2021 N S P S U R F B O A R D S .C O M

V14 1

>

FOIL CONTENTS

www.nspsurfboards.com

Photographer : Louis Castro Rider : Bruno Pitanga

Location : Brazil Board : Surf Foil

SURF FOIL BOARDS

SUP FOIL BOARDS

FOIL

AIRWING

ACCESSORIES

<

2

• FOIL BOARD OVERVIEW

4

• ALAIN TEURQUETIL - DESIGNER

5

• PRO SERIES

6

• REC SERIES

8

• PRO SERIES

10

• REC SERIES

12

• DALE CHAPMAN - SHAPER

14

• DC FOIL X Flax

15

• AIRWAVE FOIL

16

• FOIL PACKAGE

17

• FRONT WINGS

18

• REAR WING, MASTS, SHIMS, FUSELAGE & TUNING SHIMS

19

• AIRWAVE ACCESSORIES

20

• AIRWAVE OVERVIEW

21

• FOIL INSTALLATION

22

• AIRWING

24

• AIRWING FEATURES & SPECS

25

• AIRWING ACCESSORIES

26

• AIRWING MANUAL

28

• NSP ACCESSORIES

29

• FOIL BAGS

30

• TRACTION PADS

31

• PADDLES

32

• LEASHES

33

• SOFT ROOF RACKS, TIE DOWNS, RACK PADS

34

• BUOYS & FLAGS

35

• T-SHIRTS & HAT

36

FOIL BOARDS

2021 DEALER GUIDE

FOIL BOARDS

Rider : Paul Jonesy

Location : Sunshine Coast, Australia

Board : Surf Foil

3

>

FOIL BOARD OVERVIEW

www.nspsurfboards.com

SURF-FOIL PRO

NEW SHAPE

The NSP pro series Surf Foil boards are designed to optimize paddle speed, getting you into waves on the foil quickly. The lower swing weights increase maneuverability in the air and riders lose minimal speed, recovering quickly from touchdowns thanks to the bottom shape.

Length

Width

Thickness

Volume

Pro Series

4’2”

19”

3 3/16”

31.9 L

•NSSF0904

4’8”

20”

3 3/16”

37.6 L

•NSSF0905

5’2”

21”

3 1/16”

42.0 L

•NSSF0906

5’6”

22”

3 1/16”

47.0 L

•NSSF0907

REC

NEW SHAPE

The Recreational (Rec) series Surf Foil boards are designed with the same outlines and rocker as the Pro Series, but with more volume in the forward half of the board and less concave provides an easier and safer entry to the wave.

Length

Volume

Pro Series

Width

Thickness

4’8”

20”

3 3/16”

38.0 L

•NSSF0901

5’2”

21”

3 3/16”

42.6 L

•NSSF0902

5’6”

22”

3 3/16”

47.5 L

•NSSF0903

SUP-WING FOIL PRO

NEW SHAPE

This new generation of SUP-Wing foiling shapes take engineering queues from the latest Americaʼs Cup foiling boats.

By adapting key concepts to the specific needs of SUP foiling, we greatly improved bottom-end sub-foiling performance, getting you up and foiling early with minimal effort. The refined forward hull shapes deliver instant recovery from those unavoidable touchdowns.

Length

Width

Thickness

Volume

Pro Series

5’6”

24”

5 1/8”

87.6 L

•NSPF0904

5’10”

25”

5 1/8”

96.0 L

•NSPF0905

6’2”

25”

5 1/8”

101.4 L

•NSPF0906

6’6”

27”

5”

112.3 L

•NSPF0907

6’10”

28”

4 15/16 ”

125.7 L

•NSPF0908

7’2”

29”

4 15/16”

136.8 L

•NSPF0909

REC

NEW SHAPE

NSP’s Sup Wing Rec Series is designed with the same outlines and rocker as the Pro Series, but with a lbit more volume in the front half of the board and fuller rails. Overall, the increased stability makes it easier to focus on getting onto the foil and makes it easier to control during dramatic touch downs.

Length

Volume

Pro Series

4 15/16”

116.0 L

•NSPF0901

4 15/16”

128.5 L

•NSPF0902

5”

141.3 L

•NSPF0903

Width

Thickness

6’6”

27”

6’10”

28”

7’2”

29”

DC FOIL X FLAX The ultimate cross over board, perfect for learning to sup and wing foil, remove the foil add fins and you have a ripperble surf sup board.

Length 7’6”

<

4

Width 29”

Thickness 4 1/4”

Volume 116.0

Fins

Pro Series

3 x J5 FTU fins

•NCSE0901

FOIL BOARD DESIGNER

2021 DEALER GUIDE

ALAIN TEURQUETIL - DESIGNER

Renowned for his winning race board designs, Alain Teurquetil will now apply his engineering skills to designing boards that can truly fly. We are excited to expand our cooperation with Alain as he designs the second generation of SUP foil, Wing foil and Surf foil boards by NSP. New features like double concave bottoms, chinned rails, strap inserts and unique innovations like our front stringer on both the Pro models and our fuller nose concave of our Recreational range ensures our foil ranges continues to be state-of-the-art.

Whether you are passionate about foiling downwind, in the surf, on a SUP or with wings, NSPâ&#x20AC;&#x2122;s new foil shapes offer an unsurpassed experienced that gets you on the foil with ease.

5

>

SUP FOIL PRO SURF

www.nspsurfboards.com

SURF FOIL PRO

NEW SHAPE

CARBON

The NSP Pro Series Surf foil boards are designed around the same parameters as the SUP foil boards. The boards paddle fast getting you into waves faster and on the foil with ease.

Riders can now hit the water hard, lose minimal speed or momentum, and recovery is smooth after an accidental touchdown. Evolved from the last generation of foil boards that often featured flat-bottom hulls, these advanced shapes feature concave and pronounced center stringers that create a totally new experience for intermediate-to-expert foilers.

Key Features:

• The volume distribution is concentrated around the chest area to give surfers a perfect platform for paddling into waves.

• A completely new rocker with a unique front stringer line optimizes paddling speed from every paddle stroke, getting you on the wave and on the foil faster than ever before.

• A low stringer and double nose concave actively help directional efficiency, making sure that every paddle is converted into forward movement, getting you into the waves quicker.

• The forward bottom shape and chinned rails avoid any sticking or catching when they touches down, instantly rebounding the board back into flying mode.

• A refined nose volume minimizes the swing weight of the board in the air, allowing foilers to snap fast turns with confidence and balance.

• Thermoformed EVA tail pad with arch bar, side kick and pronounced tail kick and side wedges.

• Twin track foil tuning guide.

SPECIAL FEATURES

SPECS

Twin Track Mounting system and tuning guide

<

6

Carbon vector net

Length 4’2” 4’8” 5’2” 5’6”

EVA tail pad with center arch bar and side wedges Width 19” 20” 21” 22”

Thickness 3 3 3 3

3/16” 3/16” 1/16” 1/16”

Dual UD carbon stringers

Volume 31.9 37.6 42.0 47.0

L L L L

Recreational •NSSF0904 •NSSF0905 •NSSF0906 •NSSF0907

Low stringer double concave design

SURF FOIL PRO CONSTRUCTION

2021 DEALER GUIDE

SURF FOIL PRO - CONSTRUCTION

CARBON

Super Durable, Impact Resistant and Great for Surf Foiling.

SLX – Super Light Epoxy. Lightweight, responsive and extremely versatile boards.

• The standing area is reinforced with biaxial glass adding extra strength to avoid dings or dents from excessive pumping, while also helping to prevent delamination.

• The rail-to-rail carbon vector net wrap creates optimal board performance by providing unmatched flex and strength throughout the board, while making it less prone to breakage.

• The board has a consistent feel and flexes naturally with the water conditions or when pressure is applied from the rider pumping the board.

• Dual uni-directional carbon bottom stringers provide the optimum flex needed for enhanced performance.

• All boards come equipped with a NSP foiling tail pad and twin track mount.

• The twin track foil mount laminated bottom to deck in reinforced high density PU boxes for maximum strength fits perfectly for the NSP Airwave Hydrofoil, but allows for installation of many other twin track foils on the market.

Fiberglass

Securecell EPS core

Dual UD Carbon stringer nose to tail

Biaxial fiberglass reinforced standing area Carbon vector net

Fiberglass

Fiberglass

Fiberglass

Foil tracks laminated bottom to deck in reinforced High Density PU boxes for maximum strength

7

>

SURF FOIL REC

www.nspsurfboards.com

NEW

SURF FOIL REC

SHAPE

The Recreational (Rec) series Surf Foil boards are designed with the same outlines and rocker as the Pro Series, but with a less pronounced concave and a less pronounced center stringer. The Rec Series also has a bit more volume in the front section of the board and fuller rails compared to the Pro Series range.

Overall, the increased stability makes it easier to focus on getting onto the foil and really helps recovering from dramatic touchdowns while flying.

NSPʼs Protech technology is an ideal construction for this type of application, as it is combines performance and price in a very attractive package for beginning to intermediate foilers.

Key Features:

• The volume distribution is concentrated around the chest area to give surfers a perfect platform for paddling into waves. * Refined rocker for faster paddle speeds. * Shallower concaves and less pronounced stringer make maneuvering in the line up a breeze. * Fuller rails and forward volume provide great stability, allowing for quick recovering in steep take off situations • Thermoformed EVA tail pad with arch bar, side kick and pronounced tail kick and side wedges.

• Twin track foil tuning guide.

SPECIAL FEATURES

SPECS

chinned rails

<

8

Twin track mounting system and tuning guide

Length 4’8” 5’2” 5’6”

EVA tail pad with center arch bar and side wedges

Width 20” 21” 22”

Thickness 3 3/16” 3 3/16” 3 3/16”

Reduced double concave

Volume 38.0 L 42.6 L 47.5 L

Recreational •NSSF0901 •NSSF0902 •NSSF0903

increased nose volume

SURF FOIL REC

2021 DEALER GUIDE

SURF FOIL REC - CONSTRUCTION

Renowned as NSP’s line of durable, high-performance custom laminated boards offered at the most attractive price point.

• 36g molded SecureCell EPS core • Triple reinforced glass deck and rail with full 200g. glass bottom.

• The twin track foil mount laminated bottom to deck in reinforced High Density PU boxes for maximum strength fits perfectly for the NSP Airwave Hydrofoil, but allows for installation of many other twin track foils on the market.

Fiberglass 100g.

Fiberglass 160g.

Securecell EPS core

Fiberglass 200g.

Fiberglass

Fiberglass

Foil tracks laminated bottom to deck in reinforced High Density PU boxes for maximum strength

9

>

SUP WING FOIL PRO

www.nspsurfboards.com

NEW

SUP WING FOIL PRO

SHAPE

CARBON

This new generation of SUP-Wing foiling shapes take engineering queues from the latest Americaʼs Cup foiling boats. By adapting key concepts to the specific needs of SUP foiling, we greatly improved bottom-end sub-foiling performance, getting you up and foiling early with minimal effort.

The boards are balanced in the air with low swing weight. The forward bottom and rail shape is designed to maintain speed during accidental touch downs while delivering a smooth recovery.

Compared to our last generation of foil boards that often featured flat-bottom hulls, these improved shapes bring a totally new experience for intermediate-to-expert foilers with the most pronounced stringer line for increased directional momentum.

The end-result is a shape riders can easily stand on, with a very good sub-foiling efficiency and a forgiving ride when flying.

This makes the NSP Pro Series SUP-Wing foil boards perfect for waves, downwinding and wing foiling.

FEATURES: • Enough buoyancy and stability to stay comfortable when you are not on the foil.

• Early planing shape and efficient tail exit requires minimal effort to lift up and fly. It provides better sub-foiling bottom-end efficiency for paddling and wingfoiling.

• Directional efficiency when you are off the foil, so all applied forces (whether it is a paddle stroke or a kite pump) is converted into forward movement.

• The forward board shape is developed to avoid any sticking effect when touching the water surface, allowing the board to rebound instantly to flying mode.

• The volume distribution is designed to reduce the swing weight of the board when you are on the foil. This allows quicker turns and gibe moves.

• Thermoformed EVA deck pad with pronounced kick tail and side wedges.

• Twin track foil tuning guide.

• Multi-positioning foot strap inserts mid deck and tail.

SPECIAL FEATURES

SPECS

Twin track / foil tuning guide

<

10

Center ridge and foot strap inserts

Tail kick pad with t-bar center arch and side wedges

Length

Width

Thickness

5’6” 5’10” 6’2” 6’6” 6’10” 7’2”

24” 25” 25” 27” 28” 29”

5 1/8” 5 1/8” 5 1/8” 5” 4 15/16 ” 4 15/16”

Uni-directional carbon stringer deck

Volume 87.6 L 96.0 L 101.4 L 112.3 L 125.7 L 136.8 L

Pro Series •NSPF0904 •NSPF0905 •NSPF0906 •NSPF0907 •NSPF0908 •NSPF0909

Uni-directional carbon stringer deck

SUP WING FOIL PRO CONTRUCTION

2021 DEALER GUIDE

SUP WING FOIL PRO - CONSTRUCTION

CARBON

Extremely Durable, Lightweight and Fun to SUP Foil.

SLX – Super Light Epoxy. Lightweight, responsive and extremely versatile boards.

• Reinforced carbon standing area positioned just above the foil box to provide added strength during board pumping while foiling.

• The standing area is further reinforced with biaxial glass to avoid dings or dents from excessive pumping, while also helping to prevent delamination.

• Center ridge just below the EVA deck pad runs conveniently along the entire length of the deck pad allowing you to position yourself on the center of your board without looking down.

• Full-length uni-directional carbon stringer on the deck and a uni-directional hybrid carbon stringer on the bottom add strength, flexibility and foil drive.

• The twin track foil mount laminated bottom to deck in reinforced high density PU boxes for maximum strength fits perfectly for the NSP Airwave Hydrofoil, but allows for installation of many other twin track foils on the market.

EVA Center bar Fiberglass

Secure cell EPS core

Biaxial fiberglass

Carbon reinforced standing area Carbon hybrid stringer Fiberglass

Fiberglass

Fiberglass

Foil tracks laminated bottom to deck in reinforced High Density PU boxes for maximum strength

11

>

SURF WING FOIL REC

www.nspsurfboards.com

SUP WING FOIL REC

NEW SHAPE

This new generation of SUP-Wing foiling Rec shapes take engineering queues from the Americaʼs Cup foiling boats.

The Rec Series is designed with the same outlines and rocker as the Pro Series, but with a dialed down concave and a less pronounced stringer line. The Rec Series also has a bit more volume in the front section of the board and fuller rails compared to the Pro Series range.

Overall, the increased stability makes it easier to focus on getting onto the foil and really helps recovering from dramatic touchdowns while flying.

Features : * Perfect for first time sup and wing foilers. * Increased volume in the front half of the board and fuller rails compared to the pro series range, provide increased volume and stability. *Dynamically efficient bottom shape allows you to get on the foil with minimal effort. *Increase nose volume and chined rails make it easy to recover form dramatic touchdowns.

• Thermoformed EVA deck pad with pronounced kick tail and side wedges.

• Twin track foil tuning guide.

• Multi-positioning foot strap inserts mid deck and tail.

SPECIAL FEATURES

SPECS

Twin track /foil tuning guide

<

12

Tail kick pad with side wedges and foot strap inserts

Center Ridge

Length

Width

6’6” 6’10”

27” 28”

7’2”

29”

Foot strap inserts

Thickness

Volume

Recreational

4 15/16” 4 15/16” 5”

116.0 L 128.5 L

•NSPF0901 •NSPF0902

141.3 L

•NSPF0903

Fuller rails and increase nose volume

SURF WING FOIL REC CONTRUCTION

2021 DEALER GUIDE

SUP WING FOIL REC - CONSTRUCTION

Renowned as NSP’s line of durable, high-performance custom laminated boards.

NSPʼs Protech technology is an ideal construction as it is combines performance and price in a very attractive package for beginning to intermediate foilers.

Riders can now hit the water hard, lose minimal speed or momentum, and recovery is smooth after an accidental touchdown.

• 36g molded SecureCell EPS core • The standing area is reinforced with biaxial glass to avoid dings or dents from excessive pumping, while also helping to prevent delamination.

• Center ridge just below the EVA deck pad runs conveniently along the entire length of the deck pad allowing you to position yourself on the center of your board without looking down.

• The twin track foil mount laminated bottom to deck in reinforced high density PU boxes for maximum strength fits perfectly for the NSP Airwave Hydrofoil, but allows for installation of many other twin track foils on the market.

Center ridge Foot strap insert s Fibe rglass 160g .

Fibe rglass 200g .

220g. Biaxia l fibe rglass

SecureCell EPS core

2 x 160g. Fiber glas s

Fiberglass

Fiberglass

Foil tracks laminated bottom to deck in reinforced High Density PU boxes for maximum strength

13

>

SHAPER

www.nspsurfboards.com

DALE CHAPMAN - SHAPER “Any good shaper will tell you, it’s all about touch and feel.

This comes from experience, and most importantly, you have to love it.”

Dale Chapman - Shaper

Growing up in Mermaid Beach, Gold Coast, Dale Chapman (owner, shaper of DC Paddleboards) has been designing boards for riders, all over the globe, for the last 30+ years. Dale’s passion to put the best design under each individual’s feet is what drives him to continue shaping. “Our success is based on the fact that we listen to what our customers want, understand what they are hoping to achieve on the water, and deliver a board that will exceed their expectations.”

DC Paddleboards and NSP joined forces in 2012 to produce a wide range of foil surf and stand up paddleboard designs.

Dale personally shapes the prototypes in Australia. This relationship enables us to create superior, Australian designs and shapes that reach the enthusiastic sup and elite surfers internationally.

<

14

SUP 2021

FOIL SUP

DEALER GUIDE

DC FOIL X FLAX

FLAX

The DC Foil is shaped and designed by Dale Chapman. downwinding, wake foiling, tow-in or windfoiling, the DC Foil can do it all. Paired to the NSP Airwave or with conventional fins (thruster works best for fast and loose rides), this hybrid works well on- and over the surface.

Selling features:

• SLX : A premium and high performance package.

• Vacuum bonded SLX (Super Light Epoxy) core offers a lighter weight.

• Biax glass and Paulownia veneer wood deck for improved impact resistance.

• Full length uni-directional carbon stringers for added strength and added foil drive.

• Biaxial carbon reinforced foil box.

• Hand polished UD Flax Rails • Maximize every wave with power and speed.

• With a huge sweet spot for a board this size, this foil board is designed for maximum stability.

• Deck/bottom matt colour and polished rails.

• Diamond grooved EVA tail pad with side and a center T-bar ridge for easy foot placement while foiling.

Vacuum molded epoxy Fiberglass Biaxial glass

Natural flax fiber rail tape

SecureCell EPS core

Paulownia wood

Uni-directional carbon stringers

Catch waves that refuse to break and fly over the slower sections with grace and speed. The DC Foil X is an, eco-friendly board featuring flax fiber rails for added durability. The DC Foil X Flax only connects to twin-track mounting systems. If you don’t already own a foil with a tuttle-box, this is the board to go for, as we engineered the twin track system to be more tunable, more resistant to torque and easier to set up.

Biaxial carbon reinforced US fin boxes

Fins: Features foil and FTU fin box options strategically positioned to either foil or surf. FTU fin boxes, compatible with Futures® fins. J5 FTU fins supplied with each board “It’s the silence that really hits you, the first time you lift off, opens up a whole new world of wave riding!”

SPECIAL FEATURES

UD Carbon hybrid stringer

Dual mounting system with easy tuning guide

Twin track system and 3 x FTU fin boxes

SPECS

Kicktail for SUP surfing

Length 7’6”

Width 29”

Thickness 4 1/4”

Volume 116.0 L

Fins

DC Foil X Flax

3 x J5 FTU fins

•NCSE0901

15

>

AIRWAVE

www.nspsurfboards.com

M O D U L A R

H Y D R O F O I L

The 6061-T6 Aluminum twin track mounting plate perfectly balances strength and weight. Control and lift can be adjusted with the interchangeable shims under the rear wings for the right combination of lift, stability and speed.

It’s an extremely versatile foiling platform with all the necessary add-ons to allow you to customize your NSP Airwave across the entire watersports spectrum, no matter the riders weight or ability.

NSP wings feature a reinforced foam core, laminated with 100% pre-preg 3k Carbon fiber. Although more expensive to build, this construction offers the best durability.

-

13.5cm (5.31”) wide for strength and directional stability Extruded 6061-T6 anodized aircraft aluminum mast 60, entry-level or shallows (1.45kg) mast 70, Ideal first mast, perfect allrounder (1.7kg) mast 80, Advanced height for surfers, downwind, wing and windsurf (1.9kg) - mast 90, Kite, wing or windsurf and downwind (2.1kg) - mast 100, Kite, wing, windsurf and tow-in foilers (2.3kg)

B

C

D

E

This means NSP Airwave wings will handle regular wear and tear and the inevitable groundings.

- Twin track base (0.75kg) - 316 stainless Torx screws - Deep mast sleeves, CNC-milled for best strength-to-weight ratio - Bomb-proof, 6061-T6 Aircraft grade anodized aluminum base - Optional tuttle box adapter available

A

16

M

Designed with performance, hydrodynamic efficiency and durability in mind. This modular platform can be tuned for every type of foiling: Surf, SUP, downwind, tow, windsurfing, wake, kite and wingfoiling.

The backbone of the NSP Airwave is the unique 13.5cm (5.31”) wide 6061-T6 Aluminum mast. It is substantially wider than other masts for additional strength and directional stability. Connected to our beefed-up, precision CNC-cut 6061-T6 Aluminum fuselage, the Airwave will withstand loads generated from high speed turns and those inevitable wipe-outs.

<

S Y S T E

-

High-end 3k pre-preg carbon rear wings: RW 330 Flat wing (0.20kg) RW 340 M wing (0.20kg) RW 245 Downwind (0.16kg) RW 240 Radical Surf (0.23kg) RW 228 Windsurf (0.23kg)

Super strong, CAD designed precision CNC-cut 6061-T6 anodized aluminum - Fuselage 70 Standard (1.05kg) - Fuselage 85 Windsurfing (1.27kg)

High-end 3K pre-preg carbon front wings: - FW 1325 Standard (1.2kg) - FW 1700 Standard (1.55kg) - FW 2000 Standard (1.94kg) - FW 1250 Advanced (Swept wing) (1.10kg) - FW 1400 Advanced (Gullwing) - FW 1720 Advanced (Gullwing) (1.55kg) - FW 2500 Gullwing (1.87kg) - FW 1250 Downwind (Glider style) under development - FW 1450 Downwind (Glider style) (1.08kg) - FW 1650 Downwind (Glider style) (1.69kg)

FOIL PACKAGE

2021 DEALER GUIDE

FOIL PACKAGE

FOIL TRAVEL CASE

Anyone in the market for a high-performance foil shouldn’t look any further than the NSP Airwave. The Airwave foil package has everything you need and comes in a premium padded travel case with additional space for add-on wings and accessories.

-

High-quality 600D Fabric Highly durable zipper Name card holder Padded handles Custom cut interior foam compartments keep everything safe.

Fits additional add-on front wing, rear wing and mast

*Travel case will hold two front wings, two rear wings and two masts.

Both the FW 1325 and FW 1700 package include empty slots for add-ons.

ASSEMBLY KIT:

TWO AVAILABLE AIRWAVE PACKAGES:

Every NSP Airwave set comes with a handy toolbox containing all our mounting hardware: two Torx fasteners, 316 Torx stainless steel screws, foil box sliders, three CNC-cut shims for tuning, and Tef-gel for assembling your Airwave.

Choose the Airwave FW 1325 package or the FW 1700 package.

Package 1325 1700

Code

•NFOIL01 •NFOIL19 17

>

• FRONT WINGS – Allround

w . nand s pstability surf NSP’s benchmark foils - a perfect combination between w lift,wspeed

FW 1325* (Allround) (1.20kg)

•NFOIL05

With a surface of 1325cm and a width of 78cm this is the cornerstone of the NSP Airwave setup. The foil profile offers a wide range with a smooth ride and great speed.

Recommended as the perfect setup for surf, wake, light and middle weight SUP foilers.

SURFACE 1325cm2

Width 78cm (30.7”)

*Included in the Airwave FW 1325 package and sold individually. Total weight assembled 5.05kg

FW 1700* (Allround) (1.55kg)

Width 85cm (33.4”)

*Included in the Airwave FW 1700 package and sold individually Total weight assembled 5.4kg.

FW 2000* (Allround) (1.94kg)

Width 100cm (39.4”)

• FRONT WINGS - PRO (SWEPT)

Key design characteristics: Foil profile and AOA (angle of attack) delivers a gradual lift/speed slope for great control during acceleration - Low-aspect ratio for early lift - Stability through additional width and reduced curvature - Nice sweep for a deeper speed envelope - Profile and foil outline deliver great pumping performance

•NFOIL25

With less curvature for more directional stability and a wider outline, the 2000 wing is the Cadillac of the Airwave range. This wing delivers a smooth ride and just keeps going and going. A great foil for bigger riders, with great bottom end performance for surf, SUP, wake and a perfect choice for wingfoiling.

SURFACE 2000cm2

Key design characteristics: Foil profile and AOA (angle of attack) delivers a gradual lift/speed slope for great control during acceleration - Low-aspect ratio for early lift - Stability through additional width and reduced curvature - Nice sweep for a deeper speed envelope - Profile and foil outline deliver great pumping performance

•NFOIL02

The 1700 has set the performance benchmark for early lift and stable performance. On smaller days, the FW 1700 excels at Surf and SUP foiling and is an amazing option for wake foiling, freeride kite (kitewing) and windsurfing. The similar profile to the FW 1325 offers a wide range, smooth ride and it’s easy to pump. Considering the size, the speed potential of this wing is amazing. A perfect choice for smaller surf or heavier foilers wanting more lift.

SURFACE 1700cm2

boards.com

Key design characteristics:

- Diminished curvature, for sustained glide from one bump to the next - Slight winglets help directional stability - More slender profile for better control at high speeds - Foil profile and AOA (angle of attack) offers great lift at lower speeds

NSP’s more advanced foils

FW 1250* (Swept wing) (1.10kg) SURFACE 1250cm2

Width 70cm (27.5”)

•NFOIL20

Built for speed - with thinner profiles, a surface of just 1250cm and a width of 70cm this is the fastest foil in the NSP quiver. Its swept shape helps control at high speed, especially while carving hard turns. Loose and highly sensitive to rider input, it is the wing for advanced foilers.

String up a series of drawn out turns, at unimaginable speeds with the FW 1250. Designed for advanced wave riding (surf & sup), kitewings, kite surfing and tow foiling.

Key design characteristics:

- Designed to work with our standard 330 flat rear wing - Thinner profile for greater speeds - Curvature allowing for fast rail-to-rail transitions - Serious rake for carved surfing

• FRONT WINGS - PRO (GULLWING) SURFACE 1400cm2 Width 77cm (30.3”)

FW 1400* (Gullwing) (1.25kg) FW 1720* (Gullwing) (1.55kg) FW 2500* (Gullwing) (1.87kg)

SURFACE 1720cm

2

Width 94cm (37.1”)

SURFACE 2500cm2 Width 120cm (47.2”)

• FRONT WINGS - Downwind

Width 70cm (27.5”)

SURFACE 1450cm2 Width 90cm (35.4”)

SURFACE 1650cm

2

Width 110cm (43.3”)

18

•NFOIL29 •NFOIL28

This is our most popular wing for intermediate to advanced foilers. Perfect for high performance surf, SUP, wing foiling, freeride windsurf and kiteboarding.

It delivers next generation efficiency, speed, early liftoff and control. Windsurf riders say this wing delivers great natural stability that enables confident riding at all angles upwind and downwind. For wing, surf and sup. The speed and carving capabilities are unmatched.

Key design characteristics:

- Thinner profile for greater speeds - Subtle dihedral helps stability - Works in a wide range of conditions

NSP’s dedicated downwinder foils

SURFACE 1250cm2

<

•NFOIL21

FW 1250* (Glider style ) (UD) FW 1450* (Glider style) (1.08kg) FW 1650* (Glider style) (1.69kg)

•NFOIL30 •NFOIL31 •NFOIL24

These high aspect glider style wings are specifically designed for downwind foiling. The outline and foil profiles combine hydrodynamic efficiency, deliver higher speeds and excellent pump characteristics in downwind conditions. These foils are based on high-performance windsurf/ kite race designs and have been adapted for the slower speeds of downwind SUP. Pair with our RW 245 downwind rear wing.

Key design characteristics:

- Early take-off and sustained flight - Reduced profile for high-efficiency - Excellent pumping characteristics for downwind racing

• REAR WING

www.nspsurfboards.com

RW 330 FLAT WING (0.20kg) SURFACE 330cm2 Width 39.5cm (15.5”)

•NFOIL07

The allrounder - flat with mild winglets, a fast and loose rear wing that works well with all NSP Front wings. This is our go to back wing. With plenty of positive rider feedback, it makes pumping a breeze. *Comes standard with the Airwave FW 1325 foil package and the Airwave FW 1700 foil package.

SURFACE 340cm2

Width 42cm (16.5”)

SURFACE 245cm2 Width 42cm (16.5”)

SURFACE 240cm2 Width 39cm (15.3”)

SURFACE 228cm2 Width 38cm (14.9”)

RW 340 M WING (0.20kg)

•NFOIL08

This is our most stable rear wing, designed for directional stability, this wing compliments our FW 1250 and FW 1400 wings. Handling fast direction changes with ease and totally at home at higher speeds, this is the best option for freeride windsurfing, wingfoiling, kitefoiling, advanced surf and sup foilers.

RW 245 DOWNWIND (0.16kg)

•NFOIL22

High-aspect shape for efficiency, sustained flights and performance downwind. For windsurfing, use this rear wing in combination with the Fuselage 85.

RW 240 RADICAL SURF (0.23kg)

•NFOIL33

This pre-preg carbon rear-wing is held in place with two screws. With a reduced surface, your setup all come alive, enabling you to maneuver faster than before. Increased responsiveness through roll and pitch as you carve and pump your way through the swell. * supplied with specific 1 / 2 / 3 degree shims

RW 228 WINDSURF (0.23kg)

•NFOIL32

This pre-preg carbon rear-wing is held in place with two screws. Intended for windsurfing and kitesurfing specifically, the RW 228 is designed for sustained flight and an emphasis on directional stability. This is achieved by using articulated winglets and a more neutral profile. *supplied with specific 2 degree shim for 85 cm Windsurf Fuselage

• MASTS With a width of 135mm (5.31”), these masts are 22.5% wider than most others on the market. The wider cord allows for a more efficient foil profile, more directional stability and a higher rigidity 6061-T6 aircraft grade aluminum. All Airwave masts feature 3 full-length channels for increased stiffness. Airwave masts are anodized for protection and a great look, and sealed with silicone plugs to keep them watertight.

•NFOIL10

All Airwaves can be interchanged with the following add-on sizes: Mast 60cm Mast 70cm Mast 80cm Mast 90cm Mast 100cm

Entry level and shallows (1.45kg) Comes standard with any NSP Airwave package (1.7kg) More advanced surfers/will windsurf too (1.9kg) Windsurf, kitesurf and wing (2.1kg) Kitesurf and windsurfer (2.3kg)

•NFOIL23

Mounting Plate : (0.750kg) Designed to distribute loads evenly, the CNC cut, anodized aluminum Airwave base features slots for easy mounting and adjustment. The mast sits in a 4cm deep sleeve creating a rigid connection and handling considerable loads.

Tuttle Converter : For riders who would like to use the NSP Airwave for windsurfing or on SUP and surfboards with a tuttle box, simply swap the base plate for this tuttle converter and enjoy additional board options.

• FUSELAGE The regressed mounting point for the mast creates additional rigidity, strength and durability.

Airwave fuselages are designed without compromise. Our design brief was clear “must be hydro-dynamically efficient, has to be strong, stiff, cannot bend, with solid mast and wing connections and it must hold up to wipe-outs in the shore break”. Each precision fuselage is individually CNC cut from aircraft grade 6061-T6 aluminum and is anodized for protection and a great look.

Available in two sizes: Fuselage 70cm Standard in all Airwave sets (1kg) Fuselage 85cm* For free ride windsurfing (1.2kg)

•NFOIL09 •NFOIL26

* supplied with specific 2 degree shim

• TUNING SHIMS AIRWAVE PRECISION TUNING

1.0 Deg 2.0 Deg 3.0 Deg

Most hydrofoils in the market are set to a single AOA (angle of attack) at the back wing, usually varying between one- and three degrees. The Airwave is different, as it comes with three precision tuning shims, allowing the rider to adjust the AOA of the back wing to customize the balance between lift, speed, stability and turning.

For example, the 3° shim (black) allows for pumping with maximum efficiency, but is slower and at higher speeds, it generates too much lift, requiring continuous counteracting by applying front foot pressure. Switching to the 1° shim (silver) gives less lift, is harder to pump but offers maximum speed. The 2° shim (orange) is the most neutral of the three, it’s the base line we design all our foils to and is the best place to start as in regular surfing, each shim has its own feel and performance characteristics. Since a hydrofoil moves on three axis, instead of the two we recommend you experiment as your skills develop.

CODE : NFOIL15

The 85 Fuselage is for windsurfers and kitesurfing and is supplied with a 2 degree 3D printed shim. The fuselage can be used with the standard shims supplied with the Airwave set, but they are a little narrow, as the Fuselage 85 tip (tail) is wider.

19

>

AIRWAVE ACCESSORIES

www.nspsurfboards.com

AIRWAVE FOIL ACCESSORIES

M8 x 30 bolts - 4 pcs •NFOIL14 Four high-grade stainless steel bolts with M8 countersunk Torx® screws will take the required torque to secure your foil to the board without stripping. Corrosion resistant nuts, sourced for marine applications, allow tuning of your setup as you slide them up or down the twin rack mount.

Mast Screws M6 x 45 •NFOIL13

Screws M8 x 30 - 3 pcs •NFOIL11

M6 long countersunk Torx® screws mount your Airwave mast to the fuselage and mounting plate.

Mount your Front wing to the fuselage with three high-grade stainless steel bolts,

RW Screw Kit - M6 x 18 - 2 pcs

•NFOIL12

Tuttle Converter •NFOIL23

Mounting Plate •NFOIL10

Have a slalom surfboard laying around or a foilboard with a tuttle box? Now you can rig up your Airwave with a tuttle system too.

Designed to spread the load, the anodized aluminum base features screw slots instead of holes, allowing for additional fine tuning.

Torx® Allen Key T30/T40 Kit - 2 pcs •NFOIL27

100 90 80 70 60 Fuselage 70 Fuselage 85

•NFOIL09 •NFOIL26

The centerpiece of the foil. These anodized aluminum, hydro-dynamically, CNC cut fuselages measures 70 cm (27.5″) in standard form. Deep slots seamlessly attaches to the masts and hold the front wing, the back wing and the tuning shims.

The 85 Fuselage is for windsurfers and kitesurfing and is supplied with specific 2 degree shim for windsurfing

<

20

•NFOIL018 •NFOIL017 •NFOIL04 •NFOIL06 •NFOIL03

RW Tuning Shims •NFOIL15 Three rear wing anodized aluminum shims allow you to trim your foil for different water conditions. Available in 1, 2, and 3 degrees. *fitting 330 / 340 and 245 Rear Wings

Mast 60, 70, 80, 90, 100 Anodized aluminum mast with reinforced internals for unparalleled rigidity.

Available in 5 sizes – 60 cm (23.6″), 70 cm (27.5″) and 80 cm (31.4″), 90 cm (35.4″) and 100 cm (39.3″)

AIRWAVE www . n s p s u r f bOVERVIEW oards.com

2021 DEALER GUIDE

Designed as the most versatile and performance-oriented foil platform on the market. The NSP Airwave can be surfed, SUPed, towed, waked, winged, windsurfed, kited, or downwinded. The Airwave offers a perfect tune for every type of watersport you enjoy on a foil.

M O D U L A R

H Y D R O F O I L

S Y S T E

COMPONENTS X

Ideal

Possible

FRONT WINGS

Su

rf

u /S

M

p Pr

o

s

f ur

/s

up D

ow

nw

in

d W

i

ng

i fo

lin

g K

ite

i fo

lin

g W

i

nd

r su

f ak W

o ef

ili

ng R

id

l er

ev

el

CODE

FW 1325

1325cm2 / 78cm

•NFOIL05

X

FW 1700

1700cm2 / 85cm

•NFOIL02

X

FW 2000

2000cm2 / 100cm

•NFOIL25

X

FW 1250

1250cm2 / 70cm

•NFOIL20

FW 1400 FW 1720 FW 2500

1400cm2 / 77cm

•NFOIL21

2500cm2 / 120cm

•NFOIL28

FW 1250 FW 1450 FW 1650

1250cm2 / 70cm

•NFOIL30

1450cm2 / 90cm

•NFOIL31

1650cm2 / 110cm

•NFOIL24

1720cm2 / 94cm

•NFOIL29

X

Allround

X

X

Allround

X

X

Allround

X

Advanced

X

Advanced

X

X

X

X

X

X

X

X

X

Advanced

REAR WINGS RW 330 Flat Wing

330cm2 / 39.5cm

•NFOIL07

X

X

X

X

RW 340 M Wing

340cm2 / 42cm

•NFOIL08

X

X

X

X

RW 245 Downwind

245cm2 / 42cm

•NFOIL22

/ 39cm

•NFOIL33

228cm2 / 38cm

•NFOIL32

RW 240 Radical Surf 240cm RW 228 Windsurf

2

Allround

X

X

X

X

Advanced Advanced

X

Advanced

X

Advanced

MASTS Mast 60

•NFOIL03

X

X

Mast 70

•NFOIL04

X

X

Mast 80

•NFOIL06

X

Mast 90

•NFOIL017

Mast 100

•NFOIL018

X

Beginner

X

X

Allround

X

X

X

X

X

X

X

X

Advanced, Allround

X

X

X

Advanced

X

X

X

Advanced

FUSELAGE Fuselage 70

•NFOIL70

Fuselage 85

•NFOIL26

X

X

X

X

X

X X

21

>

FOIL INSTALLATION

FOIL INSTALLATION CAUTION: Do not over tighten the bolts as this will damage the foil.

1. Using the supplied Tef Gel, dab a small amount onto the threads of the two screws M6 x 18mm screws for the fuselage.

2. Attach the rear wing as shown with the two M6 x 18mm screws.

The supplied trim shims need to be place between rear wing and fuselage. Do not place the rear wing without trim shim on the fuselage as this will cause damage. Tighten by hand using the supplied allen 4mm Allen key. Never use power tools.

NSP supplied 3 shims size: • For first set up use the orange 2 degree shim. This shim works best in most conditions and allows you to get used to the whole foil set up.

• The silver 1 degree shim is faster and lifts slower. Your body weight should be set further back.

• The black 3 degree shim is slower, but lifts faster. Your body weight should be set more forward to counter-balance the down force of the rear wing.

• For our M-wing, which is available separately, we recommend the 1 degree silver shim.

• For this particular surf wing, this is the perfect set up.

3. Using the supplied Tef Gel, dab a small amount onto the threads of the three M8 x 30mm screws for the front of the fuselage.

Attach the front wing as shown. Tighten by hand using the supplied 5 mm Allen key.

4. Using the supplied Tef Gel, dab a small amount of it onto the threads of the three screws on the top of the mast.

5. Attach the mounting plate to the top of the mast using three of the M6 x 35mm supplied screws. Tighten by hand using the supplied 4mm Allen key.

6. Using the supplied Tef Gel, dab a small amount of it onto the threads of the three screws on the bottom of the mast.

7. Attach the fuselage to the bottom of the mast using remaining three M6 x 35mm supplied screws . Tighten by hand using the supplied 4mm Allen key. * Never over tighten the screws. **After the first 15-20 minutes check all screws to make sure they have not worked loose. ***After every use disassemble, wash with water and dry each piece.

<

22

www.nspsurfboards.com

2021 DEALER GUIDE

FOIL INSTALLATION

ATTACHING THE FOIL TO THE TWIN TRACK MOUNT 1. Dab a small amount of supplied Tef Gel to the threads of the four mounting screws before attaching brass nuts.

2. Thread M8 screws into brass nuts just slightly (3-4 turns) and insert brass nuts into track (2 screws in each track). Slide screws to opposite ends of the tracks.

3. Place the mounting plate in center of the track and slide the screws into the screw recess. Make sure the trailing or sharp edge of the wing is facing to the back of the board then follow the positioning guide on your board.

If you have not used this foil before we recommend setting it to the back of the box. This will keep lift to a minimum, if you require more lift move the base forward in the box.

4. Tighten your screws with the supplied 5mm Allen key. Do not over-tighten. *Never over tighten the screws. **After the first 15-20 minutes check all screws to make sure they have not worked loose. ***After every use disassemble, wash with water and dry each piece.

Rider : Harry Lee

Location : Sydney, Australia Board : Surf Foil

AIRWING

www.nspsurfboards.com

AIRWING Photographer : Sam Thom Rider : Shaan Miller

Photographer: Sam Thom Location : New Zealand Rider: Shaan Miller

Board : Surf Foil

Location : New Zealand

This user-friendly, lightweight wing is the ideal accessory for foilers, SUPers and surfers wanting to increase their time and skills on the water. The geometry of the NSP Airwing is designed to deliver smooth power, stability and flowing handling, inviting you to experience new watersport sensations.

WIDER WIND RANGE AND CONTROL The NSP Airwing is the result of tons of prototypes and hundreds of testing hours. The NSP R&D process refined the outlines, tube geometries and foil profiles to deliver a ride that is smooth and stable. The wing is a stable, low-aspect shape, balanced with moderate dihedral angles that increase performance and wind range, and help keep wingtips clear of the water.

LIGHTWEIGHT AND DURABLE With weight being an essential performance parameter, we aimed for the lowest weight possible, without compromising strength and durability.

The strut and leading-edge tips are reinforced with light, but durable PVC wear patches, while the wing tip has a longer wear strip and its corners are reinforced with TPU wear pads for additional protection on land. The NSP Airwing will perform on water, land and snow but we advise against excessive dragging over surfaces.

SHAPE DETAILS: • Refined shape design, for balanced power and efficiency • Leading edge profile and dihedral shape deliver efficient twist dynamics • Oversized and segmented leading edge for rigidity (10 segments on the leading edge for the 5m 2, 6m 2 and 8 segments for the 3m2 and 4m2) • Tapered wing tips aid twist, reduce swing weight and windage.

Size

Strut Handles

3m2 4m2 5m2 6m2

4 4 5 5

Segments Leading Edge Sections

8 8 10 10

Codes Red

Blue

•NAIR0808 •NAIR0810 •NAIR0812 •NAIR0815

•NAIR0807 •NAIR0809 •NAIR0811 •NAIR0814 *colors subject to change

<

24

AIRWING FEATURES

2021 DEALER GUIDE

GET GOING IMMEDIATELY Out of the bag, the Airwing is ready for action. First, secure the supplied leash to the leading edge. Using the low-profile valve, inflate your Airwing to a pressure no higher than 7psi.

By using one-pump technology, leading edge and centre-strut inflate together, forming a strong, flex-resistant frame. The supplied pump adapter will fit common Halkey Roberts pump nozzles, used for high-end inflatable products. *Pump sold separately

The low-aspect ratio increases the range of use, powering up quickly, with a lot of freedom of movement for the rider. The 3D dihedral profile creates additional efficiency and stability in overpowered conditions.

Lift off by giving it a few shoulder rotations, some light board pumps, and off you go. Once flying, the Airwing feels fast, balanced and can easily be tuned for power by moving your back hand between the ultra-comfy handles that run the full length of the centre-strut.

TECHNICAL FEATURES AND MATERIALS Boston high-volume valve Nobody likes to spend more time rigging up and down than necessary. A light-weight, high-diameter â&#x20AC;&#x153;Bostonâ&#x20AC;? valve allows for efficient deflating and inflating.

Tapered wingtips Smart design minimizes turbulence and increases stability of your wing,

TPU reinforcements Strategically placed TPU strips dramatically increase durability while keeping the wing light.

Camber panel By strategically placing an additional foiled strip of rip stop material between the strut and the wing canopy, the Airwing boasts a smooth pre-set profile that powers up early and maintains shape under all circumstances.

Premium comfortable handles Comfortable handles on the strut and on the leading edge allow for hours of rider comfort and gives the ability to tune the sheeting angle.

The center leading edge handle is placed as neutral as possible, and allows for complete depowering and control while you focus on carving, downwinding and surfing.

Hardcore Wingtip reinforcements Especially for rough surfaces, TPU strips reinforce the wingtips, finished off with vulcanized PVC.

Smart one-pump design A single point inflation System gets you on and off the water faster, and allows you to tune the pressure between leading edge and strut.

2-ply reinforced trailing edge Additional 2-ply strips and triple stitching protect the trailing edge from stretching, wear and tear or potential ripping.

Premium wing leash Highly durable 6mm TPU coiled wing leash with double stainless steel swivels, and double layer neoprene strap.

Twin windows PVC windows are both safe and sturdy, enabling increased visibility.

Triple stitched Proven glued and triple-stitched seams offer enhanced durability

Materials used - High-quality TPU bladder - PVC Windows - TPU reinforcements - Vulcanized PVC - Ripstop canopy - Dacron leading edge and strut

XL-Leading edge & strut Added circumference translates into stiffness, segmented shape maintains rigidity in overpowered conditions and easily powers up in low- to medium powered conditions.

Tapered tips for more aerodynamic efficiencies.

Dynamic dihedral Subtle dihedral design creates a stable wing, even in overpowered conditions.

25

>

AIRWING ACCESSORIES

www.nspsurfboards.com

UPWIND Benefit from controllable lift. Excess energy is released from the trailing edge of the upper wing.

REACHING OR DOWNWIND Retain solid shape and generate progressive power for thrilling speed runs.

WHEN OVERPOWERED Notice the Airwing rising to a horizontal angle above your head, feeling neutral and controllable.

NEUTRAL FLIGHT Sufficiently powered up, an Airwing can be held by the leading edge in one hand as it floats behind you. Concentrate on your surfing or hydrofoiling until you need Airwing power again.

AIRWAVE COMPATIBLE Designed for the NSP foiling products, the Airwing is optimized for use with the NSP Airwave and NSP SUP Foil. Note that any Airwing will also perform out-of-the-bag with other known brands, shapes and foils.

STIFF, SAFE AND STABLE Designed to maintain its shape in all circumstances, the Airwing is stiff and features a clamped valve making sure you can recover your equipment in case of a leak. *Wing Size Suitability Size Max. wind Wind range

3m2

4m2

5m2

6m2

28 knots 20-28 knots

24 knots 14-24 knots

20 knots 10-20 knots

15 knots 5-10 knots

Photographer: Sam Thom Rider: Shaan Miller Location : New Zealand

*Use this table as an indication as it is subject to skill level, rider weight, foil setup and conditions

AIRWING ACCESSORY

Airwing Hand Pump* Double action pump with gauge, 5 hose nozzles to fit most valves and foot rest pedal. *NSP Double Action pump sold separately 1

1. Airwing Hand Pump

3

Code: •NAIR0813

2. Airwing Pump Valve Adapter 2

Code: •NAIR0824

4

Airwing Bladders 3. Airwing Le Bladder Size 6.0 5.0 4.0 3.0

LE LE LE LE

Bladder Bladder Bladder Bladder

4. Airwing Generic Strut Bladders

Code •NAIR0822 •NAIR0816 •NAIR0817 •NAIR0818

Size 6.0 5.0 4.0 3.0

Airwing is supplied with:

Strut Strut Strut Strut

Bladder Bladder Bladder Bladder

Code •NAIR0823 •NAIR0816 •NAIR0817 •NAIR0818

• Airwing backpack • 6mm TPU coiled wing leash with double stainless steel swivels • Repair patch • Anodized aluminum pump valve adapter *NSP Double Action pump sold separately

Airwing Backpack

For easy transportation, storage and the carrying of a pump and additional accessories.

• Padded adjustable straps • Inside pocket • Drain hole/air vent <

26

22002211 DDEEAALLEERR GGUUI IDDEE

AIRWING

Rider : Dane Gillett

Location : Splash Guest House,Chiba Japan Product : Airwing

27

>

AIRWING

www.nspsurfboards.com

AIRWING MANUAL

<

28

NSP ACCESSORIES

2021 DEALER GUIDE

• PADDLE RANGE • LEASHES

ACCESSORIES

• BOARD BAGS • TRACTION PADS • ROOF RACKS • BUOY & FLAGS • T-SHIRTS & HAT

29

>

FOIL BAG

www.nspsurfboards.com

FOIL BAGS Foil Day Bag

Foil Travel Bag

• • • • • • •

• Travel bag 8mm • Durable 8mm padded bag Polysack inside and out and 600D reinforcement at tail • Ideal for travel with name tag slot • Carry handle • Detachable padded shoulder strap • Rust-proof hardware • Fin slot

4mm Polysack inside and out Ideal for day trips name tag slot Carry handle Detachable padded shoulder strap Rust-proof hardware Fin slot

4mm

8mm

Code NSP NSP NSP NSP NSP

<

30

Surf Foil Day Bag 4’8” Surf Foil Day Bag 5’10” Surf Foil Day Bag 5’6” SUP Foil Day Bag 6’10” SUP Foil Day Bag 7’6”

•NABB0860 •NABB0861 •NABB0827 •NABB0828 •NABB0850

Surf Surf Surf Surf Surf

Foil Foil Foil Foil Foil

Travel Travel Travel Travel Travel

Bag Bag Bag Bag Bag

4’8’’ 5’10’’ 5’6’’ 6’10’’ 7’6’’

Code

•NABB0863 •NABB0864 •NABB0848 •NABB0849 •NABB0851

TRACTION PADS

2021 DEALER GUIDE

Front pad (Only)

TRACTION PADS Whether you are foiling, surfing or paddling – the NSP traction pads provide long-lasting grip and confidence. Especially in foiling, a delicate balance is required to get you flying over the surface of the water and your feet need precise positioning to control pitch, roll and yaw.

Always centered

NSP tail pads feature a kicktail and a mild dome in the center of the pad.

The ridges of the dome will make sure your back foot finds the dead center of your board without ever looking down.

•NACC0710 Traction Pad Front Blue

Tail pad (Only)

Thermoformed texture ensures your back foot stays planted over the mast at all times. For hard pumping or committing to a tight radius, get that extra leverage by moving your back foot against the kicktail and force the last bit of performance from your board.

More durable

There is nothing worse than a peeling deck pad, which is why NSP uses premium 3M adhesives, as it provides the best possible bond between your board and the thermoformed EVA. Different from conventional EVA, thermoforming gives these pads a more abrasion-resistant layer that will hold up longer. Make sure your board is properly cleaned up before applying the pads, and wait 24 hours before hitting the water to get the best possible bond for years to come. Removal is easiest with a hot air gun and some soapy water.

•NACC0802 Tail pad Blue

Versatile patterns

A 3-piece tail pad is the most versatile pattern that still offers variable width and an arched center strip. It’s the easiest to install, offers tons of grip and will work on any board. In combination with the 4-piece pattern for the front part of the deck, you should have the standing area of your board covered.

Directional diamond-shaped pattern

The deeper the grooves, the more resistance against slipping and superior traction.

Kick & Arch

Performance riders benefit from a 45 degrees kick whenever your foot needs to be well-placed to blow out a wave. Apart from the comfort aspect, an arch helps your backfoot instinctively find the centre line of your board without ever having to look down.

Sold as a package •NACC0708 - Traction Pad Set black Length tail pad: 33.8cm Length deck pad: 56.8cm Width: Variable Color: Black/Night Blue

Solid tail kick

Directional diamond-shaped pattern

31

>

PADDLE

www.nspsurfboards.com

PADDLE RANGE • SPEEDSTER

CARBON 100% FIXED 81 & 86

SHAFT WIDTH CODE NEW GRAPHIC

86 sqi blade

NEW GRAPHIC

81 sqi blade

• SPEEDSTER

29

•NAPD0802

mm

29

•NAPD0801

26

•NAPD0804

mm

450 grams

435 grams

CARBON 100% RDM FIXED 81 & 86 NEW GRAPHIC

86 sqi blade

mm

440 grams NEW GRAPHIC

81 sqi blade

26

mm

425 grams

•NAPD0803

• Ideal for those competing on the pro racing tour or for those who just want more speed. The Reduced Diameter Shafts (RDM) at 26mm are great for kids, women or paddlers with smaller hands.

• ALLROUND

COCO CARBON HYBRID ADJUSTABLE 2pcs 86

NEW GRAPHIC

2pcs

29

mm

590 grams

•NAPD0805

• A lightweight option ideal for recreational paddlers who are eco-concious and who like to travel with their paddle or share with others.

• ALLROUND

CARBON HYBRID ADJUSTABLE 2pcs & 3 pcs 86

NEW GRAPHIC

3 pcs

810 grams

NEW

2pcs

750 grams

GRAPHIC

• Ideal for recreational paddlers who are eco- and price conscious and who like to travel with their paddle or share with others.

• ALLOY

29

mm

•NAPD0808

29

•NAPD0807

mm

MOQ = 10 pieces per box

ADJUSTABLE 2pcs 94

2pcs

29

mm

•NAPD607

29

•NAPD0901

NEW GRAPHIC

2pcs

• Ideal for recreational paddlers, schools or rental centers. <

32

mm

SUP LEASHES

2021 DEALER GUIDE

The ultimate combination of strength, stretch and elasticity. Durable Thermoplastic Polyurethane (TPU) leashes with two swivels, leash string, key pocket and double layered velcro strap.

SUP/ SURF

SUP COIL • High-quality BASF™ TPU • Coiled 7mm cord • Double stainless steel swivels

• Double layer neoprene calf strap • Integrated key pocket • Rail saver

Length

Diameter

Code

6’ 10’

7 mm 7 mm

•NALR0606 •NALR0607

• 7mm TPU • Double Stainless steel swivels • Double layer neoprene ankle strap

Length

• Integrated key pocket • Rail saver • Calf fit for 10’ 9mm

Diamete

6’ 8’

9’ 10’

7 7 9 9

Code

mm mm mm mm

•NALR0602 •NALR0603 •NALR0802 •NALR0801

Coiled 7mm cord

Triple wrap rail saver

Durable cord 7mm & 9mm

Triple wrap rail saver

Double layer neoprene strap

Double stainless steel swivels

Double layer neoprene strap

Double stainless steel swivels

WAIST BELT

Rail Tape

• • • • • •

Protect your SUP rails with 3M protection tape.

Available in 2x 7.5 cm x 2 meter rolls.

High-quality nylon webbing belt Comfortable neoprene front liner Swivel mount to avoid tangling Quick release clip One size fits all Compatible with all NSP leashes

Code :

•ACC019

Code : •NALR0605

Leash sold separately Surf leash available in 6’, 8’,9’ and 10’

Leash sold separately SUP Coil available in 6’ (7 mm) and 10’ (7 mm) 33

>

ROOF STRAPS

www.nspsurfboards.com

SOFT ROOF RACKS - Single & Double NSP’s Soft Roof Racks are perfect for carrying your surf, sup, or foil boards to the beach on the roof of your car.

The Soft Racks are secured with heavy duty nylon straps that are designed to wrap around the inside of your car while safely securing your boards to the roof. The durable cam buckles keep your boards in place without sliding during transport. The Soft Racks are designed to work on most vehicles.

Available in a Double or Single rack sizing.

Front

Rear

Code : •NACR0903

Rear

Code : •NACR0904

ROOF RACK PADS

NSP’s heavy-duty Tie Down Straps are ideal for securing your surf, foil and SUP boards to the roof of your car. Made with strong, yet soft nylon straps that will easily secure your boards without scratching the board. The heavy-duty cam buckles are encased in a padded EVA to also avoid damage to your board or car.

NSP subtly branded roof rack pads easily attach to your existing roof racks for a padded landing for your surf, sup or foil boards.

The Roof Rack Pads are designed with a foam core wrapped in a durable 600D water-resistant fabric and fit most standard sized round or square roof racks.

Available in one size: 15’7” (475cm)

Available in one size: 17” pads

Rear

Code : •NACR0901 34

Front

TIE DOWN STRAPS

Front

<

Features: • Single racks hold up 3 shortboards or 2 longboards • Double racks hold up to 6 surfboards • Universal fit for most cars, trucks, and SUVs • Thick, long length nylon straps • Heavy-duty, corrosion-free buckles encased in padded EVA to avoid scratching the vehicle.

• Water-resistant, durable, nylon-wrapped, soft rubber pads.

• Compact size and easy to store.

Front

Rear

Code : •NACR0902

BUOY & BEACH FLAGS

2021 DEALER GUIDE

BUOYS Designed utilizing our durable PVC inflatable board material, our racing buoys are equipped with 4 heavy-duty D-rings for easy and secure anchoring in any lake or open ocean. Great for race, demo events and promotions.

CODE Pyramide inflatable racing buoy 200x200 cm (Orange) Pyramide inflatable racing buoy 120x120 cm (Orange)

Side view

BANNERS BEACH FLAG

•NACC0702 •NACC0703

Bottom view with heavy duty reinforced d-rings

CODE NSP Banner Set Red (300x90cm) NSP Flag (200x98cm)

NSPACBNR16RD NSPACFG16RD

CODE NSP Beach Flag Set

NSPACBCHFLG16RD

35

>

T-SHIRTS & HAT

www.nspsurfboards.com

:

Men NSP 3

Women NSP 3

Fabric : Cotton 100%

Silk screen

Non-fading, non-shrinking, NSP branded shirts.

Back

Fabric : Cotton 100%

Silk screen

Back Front

Front

Front

Front

Back

Back

S, M, L, XL

S, M, L, XL

Men Classic Van

Fabric : Cotton 100%

Silk screen

Back

Women Classic Van

Back

Silk screen

Front

Fabric : Cotton 100%

Front Front

Front

Back

Front Back

Back

S, M, L, XL

S, M, L, XL

Men Coco

Fabric : Cotton 100%

Silk screen

Back

Women Coco Silk screen

Front

Back Front

Front

Front

Back

S, M, L, XL

<

36

Fabric : Cotton 100%

Back

S, M, L, XL

T-SHIRTS & HAT

2021 DEALER GUIDE

Men surf

Trucker Hat

Fabric : Micro polyester

Silk screen

One size fits all

Back Front

Front

Back

S, M, L, XL

Code : â&#x20AC;¢NHAT0901

Men Race

Front

Fabric : Micro polyester

Silk screen

Back

Men

Women Back

Front

Front

Back

S, M, L, XL

T-SHIRT

M

L

XL

XXL

NAPP0801M

NAPP0802M

NAPP0803M

NAPP0804M

NAPP0805M

White

NAPP0806M

NAPP0807M

NAPP0808M

NAPP0809M

NAPP0810M

Burgundy

NAPP0811M

NAPP0812M

NAPP0813M

NAPP0814M

NAPP0815M

Blue

NAPP0816M

NAPP0817M

NAPP0818M

NAPP0819M

NAPP0820M

Black

NAPP0821F

NAPP0822F

NAPP0823F

NAPP0824F

Off White

NAPP0825F

NAPP0826F

NAPP0827F

NAPP0828F

Burgundy

NAPP0829F

NAPP0830F

NAPP0831F

NAPP0832F

Black

NAPP0833M

NAPP0834M

NAPP0835M

Off White

NAPP0836M

NAPP0837M

NAPP0838M

NAPP0839M

Grey

NAPP0840M

NAPP0841M

NAPP0842M

NAPP0843M

Black

NAPP0844F

NAPP0845F

NAPP0846F

NAPP0847F

White

NAPP0848F

NAPP0849F

NAPP0850F

NAPP0851F

Grey

NAPP0852F

NAPP0853F

NAPP0854F

NAPP0855F

Black

NAPP0856M

NAPP0857M

NAPP0858M

NAPP0859M

White

NAPP0860M

NAPP0861M

NAPP0862M

NAPP0863M

Off White

NAPP0864M

NAPP0865M

NAPP0866M

NAPP0867M

Grey

NAPP0868F

NAPP0869F

NAPP0870F

NAPP0871F

White

NAPP0872F

NAPP0873F

NAPP0874F

NAPP0875F

Off White

NAPP0876F

NAPP0877F

NAPP0878F

NAPP0879F

Grey

Men Race

NAPP0880M

NAPP0881M

NAPP0882M

NAPP0883M

Men Surf

NAPP0885M

NAPP0886M

NAPP0887M

NAPP0888M

Men NSP 3

Women NSP 3

S

Men Classic Van

Women Classic Van

Men Coco

Women Coco

NAPP0884M

COLOR

White Dark Blue

37

>

www.nspsurfboards.com

NATURE SURFING PRODUCTS

Photograopher : Erik Aeder Rider : Alex Bicrel Location : Hawaii Board : Sup Foil <

38