Compad instructions

TECHNICAL SPECIFICATION

SECURED AND SIMPLIFIED

compad

COMMUNICATIONS PAD

connectivetouch

connectivetouch

速

secured and simplified

SECURED AND SIMPLIFIED

TM

connectivetouch

速

secured and simplified

TM

conne

secured and sim

connectivetouch

速

secured and simplified

TM

1. Operating voltage is 3v (2x1.5v AA cells) 2. Switch On by pressing “I/O” key for 2 seconds 3. Display shows “Enter Pswd” 4. Enter a 4 digit password Press I/O key for 2 seconds to switch on ENTER PASSWD

Admin PW entered

ADMIN MENU ENROL ADMIN

5. Admin Menu ENROL ADMIN (UP-ARROW)

ENROL USER (UP-ARROW)

ENROL SUPERVISOR (UP-ARROW)

COMPAD ENROL USER

Supervisor PW entered

DELETE USER (UP-ARROW)

GET USERS (UP-ARROW)

ADD ADMIN (UP-ARROW)

DELETE ADMIN (UP-ARROW)

ADD SUPERVISOR (UP-ARROW)

DELETE SUPERVISOR (UP-ARROW)

DISPLAY SUPERVISOR (UP-ARROW)

DISPLAY USER (UP-ARROW)

CHANGE PASSWORD

Supervisor PW required

(UP-ARROW)

DELETE ALL USERS (UP-ARROW)

DELETE ALL SUPERVISORS

Notes on Admin Menu’s: • Enrol Admin – to enrol admin, press ENTER key on keypad and display will show ENROLLING… <ADMIN NAME> Press ENTER key again and display will show POINTTOLOCK & PRESS SEND THE USER MUST PUT HIS/HER FINGER ON THE FINGER PRINT SENSOR BEFORE THE SEND KEY IS PRESSED ON THE KEYPAD.

When the SEND key is pressed the display will show After a delay of around 10seconds, the display will show (if successful) ENROLLED OK PRESS ANY KEY NOTE: User must keep finger on the fingerprint

sensor for this time.

If enrolment fails, the display will show NO LOCK RESP PRESS ANY KEY • Enrol User – same procedure as above except user will be asked to ENTER NAME <USER NAME> The name is entered using the keypad keys (up to 12 characters).

Characters will roll at the same cursor position if the same key is pressed but if there is a pause of about 1 second, the same key will enter characters at the next cursor position.

NOTE: Pressing 0 key on the keypad after entering the name will

abort the menu if a mistake is made.

• Enrol Supervisor – same procedure as above • Delete User – This menu must only be used if the user list has been downloaded previously from the lock (see Get Users menu below). When ENTER key is pressed at this menu, the following screen is displayed.

Scroll using the arrow keys to the correct user name.

The LOCK must be put into active mode PRIOR to sending the delete command by placing a finger for at least 3 seconds on the finger print sensor (does not have to be an enrolled finger).

If successful, the display will immediately show SENDING WAITâ&#x20AC;Ś.

Followed by DELETED!! PUSH ANY KEY If communications with the lock is unsuccessful, the display will show SENDING WAIT....

Followed by NO LOCK RESP PUSH ANY KEY If the user does not exist, the display will show USER UNKNOWN PUSH ANY KEY (This may also happen if the list has not been downloaded and the ComPad store will have the old list).

REPLACE OLD? YES (1) NO (0)

• Get Users – This will download the user list from the Lock.

Press ENTER and the display will show REPLACE OLD? YES (1) NO (0) If 1 key is pressed, the list stored in the ComPad will be deleted and after a while the display will show POINT TO LOCK AND PRESS SEND The Lock must be put into active mode as described above before pressing the SEND key.

After a delay of about 40 seconds, the display will show LIST LOADED PUSH ANY KEY • Delete Admin – This menu will delete the existing Admin.

Press ENTER key and the display will show ADMIN MENU YES (1) NO (0) If 1 key is pressed, the Admin will be deleted (including the password). The display will show ADMIN MENU DELETING....

Followed after a few seconds by DELETING.... DELETED!!

and then a few seconds later by ENTER ADMIN NAME <NEW NAME> The new name is entered using the keypad and then pressing ENTER will show ENTER ADMIN PW <4 DIGIT PW> The Admin enters the new 4 digit password and then presses the ENTER key.

• Add Supervisor – Adds supervisor (up to 5 are allowed).

Press ENTER and the display will show ENTER NAME <NEW NAME> User enters name using the keypad. After the name has been entered, the user press ENTER key. The display will show ENTER SUPERVISOR PW <4 DIGIT PW> A 4 digit password is entered by the user. (Note: This only stores the Supervisor name and password in the ComPad. No information is transferred to the Lock. To enrol the Supervisor into the Lock, the Enrol Supervisor menu must be used.)

• DelSupervisor – This deletes the supervisor.

Pressing ENTER displays SCROLL UP/DN <SUPERVISOR NAME> Using the arrow keys, the list can be scrolled. Press ENTER when the required name appears and press ENTER. This will delete the supervisor and the password immediately from the ComPad. (Note: to delete the Supervisor from the Lock, the user list must be downloaded and the supervisor deleted (all types of users appear as users in the downloaded list).

• Disp Supervisors – displays all supervisors added to the ComPad. Press ENTER at this menu and with the arrow keys, scroll through the list.

• Display Users – This menu allows the downloaded user list to be scrolled.

(Note: if a user is deleted from the Lock, it will NOT be deleted from this list. The lsit must be downloaded again to update once all deletions required have been done.)

• Change Password – This changes the Admin password.

Press ENTER and the display will show CHANGE PASSWORD <NEW 4 DIGIT PW> User enters the new 4 digit password. Display then shows

When all 4 digits have been entered, the display shows (for a few seconds) CONFIRM <NEW 4 DIGIT PW> PASSWORD CHANGED • Del All Users – This deletes all users in the Lock. Note the LOCK must be put into active mode PRIOR to sending the delete command by placing a finger for at least 3 seconds on the finger print sensor (does not have to } be an enrolled finger).

• Del All Supervisors – All supervisors are deleted from the ComPad. When ENTER is pressed, the display will show DELETING...

DELETED ALL SUPERVISORS All passwords and Supervisors are deleted. (Note: The Supervisors are NOT deleted from the Lock. To delete the Supervisors from the Lock, the user list must be downloaded and the supervisors deleted one at a time (all types of users appear as users in the downloaded list).

6. Supervisor Menu On switch on, if a supervisor password is entered, the ComPad will display Supervisor menu’s. The display will show COMPAD ENROL USER

• Enrol User - This is as per the Admin Menu ® • Get Users – This is also as per the Admin Menu

connectivetouch secured and simplified

TM

Automatic Switch off If no activity is detected on the keypad, the unit will turn off automatically after approximately one-and-half minutes to conserve power.

ctivetouch

®

secured and simplified

TM

connectivetouch

®

secured and simplified

connectivetouch

®

secured and simplified

TM

Connective Touch Limited 31 Loudon Avenue, Coundon Coventry CV6 1JN United Kingdom t: +44 (0) 24 7626 9035 f: +44 (0) 24 7632 3001 e: info@connectivetouch.com www.connectivetouch.com

TM

connectivetouch

速

h

secured and simplified

ED

TM

nectivetouch

速

secured and simplified

TM

compad

connectivetouch

速

COMMUNICATIONS PAD

secured and simplified

connectivetouch

速

secured and simplified

TM

TM