Product Guide Tassullo by Tassullo Materiali

PRODUCT GUIDE

1 www.tassullo.com

buildings

PRODUCT INDEX T-SPAN > leveling / bonding mortar for calcium silicate blocks

1 - NEW BUILDINGS MASONRIES AND PARTITIONS

mortars

T200 > high workability bedding mortar

p. 36

T300 > bedding mortar

p. 36

T-SPAN > bonding / leveling mortar for calcium silicate blocks

MASONRIES AND PARTITIONS

plasters

T200 > high workability bedding mortar

p. 36

T300 > manual plaster

p. 36

T501 > conventional plaster

p. 37

TL84 > high yield lightweight plaster

p. 38

TL97 > fireproof plaster

p. 38

T-cream > high workability plaster

p. 39

T50S > waterproof plaster

p. 39

T5FB > fiber-reinforced plaster

p. 40

TLTX > primer and consolidating acrylic latex for plasters

p. 40

MASONRIES AND PARTITIONS

exposed surface mortars

T170-P > exposed surface masonry mortar

p. 41

T170-PS > exposed surface waterproof masonry mortar

p. 41

T270-P > exposed surface masonry mortar

p. 42

T270-PS > exposed surface waterproof masonry mortar T-BLOCK > mortar for exposed surface concrete blocks

MASONRIES AND PARTITIONS

p. 43 p. 43

special mortars p. 44

T-192 D > infilling thermal mortar

p. 45

top coat plasters

T-MULTI/sf, sg > top coat plaster/ plaster primer

p. 47

Grassello > air binder paste

p. 47

TRG/03 > gypsum-based top coat plaster for interiors

p. 48

FINISHING AND LEVELING

p. 48

T600-01 > fine white intonachino plaster finish for exterior finishing

p. 49

Tassullo finishing > colored minerals finishing p. 49

p. 45

special binders for floor screeds

MIXTO PAVI > special binders for floor screeds

p. 50

MIXTO PAVI B > low thickness special binder for floor screeds

p. 50

MIXTO PAVI R > quick drying special binder for floor screeds

p. 51

FLOORS

self smoothing leveling

T-LIVEL > self-leveling top coat plaster

THERMAL INSULATION

SEALING MORTAR

THERMAL INSULATION

p. 56

p. 58

finishing p. 58

p. 59

ISI-FISS > high yield and high workability cladding bonding agent

p. 59

polystyrene plate cladding

ISI-THERM > expanded polystyrene thermal insulation system

p. 60

2 - HYSTORICAL BUILDINGS

floor screeds

PAVI/1 > sub-base thermal insulating lightweight p. 52 floor screed MASSETTO > ready to use floor screed

p. 52

T48S/N > quick drying floor screed

p. 53

T48S/B > low thickness floor screed

p. 53

BINDERS Fenix NHL5 > NHL5 certified light natural hydraulic lime

T20V Color > colored sealing mortar as per sample

p. 70

T25V > machine applied plaster

p. 71

T30V > plastering mortar

p. 72

T30V/Fibro > fiber-reinforced plastering mortar

p. 72

T30S > breathable waterproof plastering mortar

p. 73

TAØØ/TAØ1/TAØ2/TAØ4 > extra fine, fine, medium, coarse white top coat p. 73 plaster/primer TBØØ/TBØ1/TBØ2/TBØ4 > extra fine, fine, medium, coarse white top coat plaster p. 74 TF01/TF02/TF04 > fine, medium, coarse waterproof finishing in natural hydraulic lime

p. 74

TFS1 > breathable waterproof finishing in NHL5 lime

p. 75

DEHUMIDIFICATION AND WATERPROOFING p. 66

Fenix NHL 3,5 Chiara > NHL 3.5 certified natural p. 67 hydraulic lime Grassello > air binder paste

p. 70

FINISHING AND LEVELING

cladding bonding agents

TK01/gr, bn > plate thermal cladding bonding agents

THERMAL INSULATION

T20V > sealing and exposed surface-masonry mortar

PLASTERS

top coat plasters

TAØ2 > medium primer top coat plaster

THERMAL INSULATION

p. 56

thermal plaster

Tassullo finishing > colored minerals finishing

exterior finishing

T600-00 > extra fine white intonachino plaster finish for exterior finishing

FLOORS

TERMO-TASS > thermal insulating plaster

interior finishing

TF1000 > fine mortar

FLOORS

T-FLASH > line marking and holes filling quick set mortar

FINISHING AND LEVELING

TBØØ/TBØ1/TBØ2/TBØ4 > extra fine, fine, medium, coarse white top coat p. 46 plaster

FINISHING AND LEVELING p. 37

p. 46

p. 67

T30S > breathable waterproof plastering mortar p. 75 TLast-100 >reclaiming and dehumidifying cycle

p. 76

STONE ELEMENTS RECONSTRUCTION T-Stone > stone elements reconstruction products p. 77

bonding adhesives

T-Fix > interior professional adhesive

p. 54

T-Fix IE > interior and exterior professional adhesive

CONSOLIDATION Fenix-B > consolidation injection mixture

p. 68

p. 54

T30rc > consolidating rendering grout

p. 68

T-Fix FLEX > flexible professional adhesive

p. 55

TBL > lightweight or fiber-reinforced grout

p. 69

T-Fix HP > high performance professional adhesive

p. 55

T-FLASH Restauro > quick drying mortar for renovation and safety measures p. 69

THERMAL INSULATION TERMO-BI > natural thermal plaster

p. 77

PRODUCT INDEX

3 - NATURAL BUILDINGS

4 - REINFORCED CONCRETE BUILDINGS

WHITE SYSTEM > calcium silicate thermal insulation system

p. 102

BINDERS

CONSOLIDATION AND RESTORATION

BROWN SYSTEM > wood fiber thermal insulation system

p. 102

ISI-THERM > expanded polystyrene thermal insulation system

p. 102

natural hydraulic lime

BIO-E NHL5 > NHL5 certified natural hydraulic lime

p. 82

TCA3/T > fiber-reinforced mortar for light structural concrete (LSC) restoration p. 92

Grassello > air binder paste

p. 82

TCA3/C > casting mortar for fillings

MASONRIES AND PARTITIONS

TCA-MI > passivating fiber-reinforced mortar for restoration of steel bar cover

mortars

BIO-E/RC > bedding mortar

p. 83

BIO-E/P2 > partitioning mortar

p. 83

MASONRIES AND PARTITIONS

plaster

BIO-E/RC > consolidating rendering mortar

p. 83

BIO-E/P > manual plaster

p. 84

BIO-E/P1 > spraying plaster

p. 84

FINISHING AND LEVELING

top coat plasters

BIO-E/RASANTE > top coat plaster

FINISHING AND LEVELING

p. 85

finishing

Bio-e/FINITURA > colored finishing

FLOORS

p. 85

floor screeds

BIO-E/FONDO > floor screed

p. 86

BIO-E/SOFT > filling floor screed

p. 86

FLOORS

tile bonding agent

TADP/C > tile bonding agent

THERMAL INSULATION

p. 87

thermal plaster

TERMO/BI > natural thermal plaster

THERMAL INSULATION

p. 87

cladding in natural cork

TK01/Ch > top coat plaster bonding for claddings p. 88 T-GREEN > insulating panel in cork

p. 88

p. 92

TOP COAT PLASTER FOR CLADDING SYSTEM p. 93

TCA1 > anti-carbonation top coat plaster for reinforced concrete structures

p. 93

TC-Paint > protective painting for reinforced concrete structures

p. 94

Ti-253 > corrosion inhibitor protective coat

p. 94

FASTENING AND RECONSTRUCTIONS T-FLASH/FR > high resistance quick drying mortar for fastening and reconstruction p. 95

WATERPROOFING IDROTASS > dual component waterproof leveling p. 95

PROTECTIVE SYSTEM TP-551 > passivating grout

p. 96

THERMAL INSULATION TERMO-TASS > thermal insulating plaster

p. 96

ISI-THERM > expanded polystyrene thermal insulation system

p. 97

RED SYSTEM > mineral wool thermal insulation system

p. 97

ISI-FISS/gr, bn > bonding/top coat plaster for expanded polystyrene plate p. 103 ISI-FISS MEDIO > bonding/ top coat plaster with medium particle size for eps plates

p. 103

ISI-FISS SOFT > bonding / lightweight top coat plaster for plate claddings

p. 103

ISI-FISS CALCE > high breathability lightweight bonding / top coat plaster in NHL5 lime

p. 103

GREEN SYSTEM > thermal insulation system in natural cork

p. 101

RED SYSTEM > mineral wool thermal insulation system

p. 101

MASSETTO > ready to use floor screed

p. 114

PAVI/1 > sub-base thermal insulating lightweight floor screed

p. 114

T48S/N > quick drying floor screed

p. 115

T48S/B > low thickness floor screed

p. 115

T-LIVEL > self-leveling top coat plaster

p. 116

T-FIX > professional adhesive for interiors

p. 116

THERMAL INSULATION BROWN SYSTEM > wood fiber thermal insulation system

7 - ADVANCED SYSTEMS

TK01/Ch > bonding agent – BIO-E NHL5 natural hydraulic lime top coat plaster p. 103

FIREPROOFING

p. 117

TRF-AC > protective coating for passive protection p. 120 of the steel structures

THERMAL PLASTERS AND MORTARS T-MIM > thermal insulating mortar

p. 105

T-192D > infilling thermal insulating mortar

p. 105

TERMO-TASS > thermal insulating plaster

p. 106

TERMO-BI > natural thermal plaster

p. 106

TRF-BA > fireproof expanding product

p. 121

TRF-EL > fireproof coating for cable ducts sealing p. 121 TRF-MU > fireproof masonry plaster

p. 122

TRF-SA > fireproof mobile barrier

p. 122

WATERPROOFING IDROTASS > dual component waterproof leveling p. 124

6 - WOOD HOUSES

LINE MARKING REPAIRS

T-WOOD RASANTE > top coat plaster for OSB and PLYWOOD wooden panels p. 112

CLADDING SYSTEMS

p. 113

FLOOR SYSTEM

ISI-FISS SOFT/CALCE > bonding agent – high breathability light top coat plaster in NHL5 lime p. 103

WALL SYSTEM

5 - ENERGY SAVING

T-WOOD PRIMER > adhesion promoting primer for wood-based panels

T-WOOD INTONACO > NHL5 natural hydraulic lime plaster

T-FLASH > line marking and holes filling quick drying mortar

p. 126

p. 112

T-WOOD PROTETTIVO > protective dual component for waterproofing of the wooden structures p. 113

Choose Tassullo because for 100 years it has guaranteed solutions and high-performance and quality products.

For 100 years Tassullo has produced solutions and avant guard systems for all sectors of the building industry,from new construction to renovation, from historic preservation restoration to sustainable construction. Since 1909 Tassullo has been a synonymous with innovation, high performance and respect for the environment. A

construction that is environmentally

friendly and finds the most efficient solution in Tassulloâ&#x20AC;&#x2122;s natural hydraulic lime. For this reason it is better to choose Tassullo: real experts in techniques and materials for building, leaders in research & development using a centenarian know how that has nowadays become an important heritage in order to design and build

in the new

millennium. Tassullo means to have a single contact from the extraction and processing of raw materials until the distribution and promotion of the final product.

Tassullo Research Centre, South side

Tassullo Research Centre, the building was awarded a prize at the Competition of Architecture for the following period 2001-2008 6

For more than a century leaders in building 7

Choose Tassullo because innovation has always been the driving force behind our work.

For us innovation

means to study and

implement solutions, systems and materials for construction that can redefine methods of application and quality standards. For this reason, day after day, we invest more resources for further research. Our new Research Center has been created to coordinate all the research & development laboratories of the Tassullo Group. It operates through a team of experts - engineers, chemists, physicists, architects and restorersthat continuously develops

products that

meet and often anticipate the market needs. The new Center works in close collaboration with various Italian and European University institutions and

organizations and has

become a constant reference in the field of research.

Inside the Research Centre; laboratories inside the chemical area

Research is at the basis of our products 8

Choose Tassullo because it introduces the trend of the new standards on the building industry. At Tassullo, research does not follow empty words, but it is realized every day in facts, products and projects where the major target is to become a technological leader in the world of construction. For this reason Tassullo has started several research projects, including:

THE RESTORATION OF MODERN BUILDINGS Tassullo has signed a research protocol with MiBAC (Ministry of Heritage and Cultural Activities) to identify and test methodologies for the restoration and the conservation of contemporary architecture. CONSOLIDATION OF HISTORICAL MASONRY Tassullo cooperates with the University of Padova at the laboratories ENEA in Rome in order to test the behaviour of historic masonry buildings subjected to seismic stress and formulate appropriate restoration technologies. DISWALL AND SEISMIC IMPROVEMENT An international project that has developed innovative

technologies and new building

processes in the field of seismic improvement of new constructions.

CONSOLIDATION: Dynamic testing of buildings in stone masonery at the ENEA laboratory in Rome in collaboration with the University of Padova

Sampling of the Hydroelectric Generating Station coating in Taio .Architect Gio Ponti’s work (1952),in the research field on modern building restoration.

The architectural building Forlì “Fondazione Garzanti”. Architect Gio Ponti’s work (1957), the subject of the Research Protocol between Tassullo and MiBAC.

At Tassullo research is based on facts and not on words 10

Choose Tassullo because our greatest aim is to be close to our customer.

Since always to be close to our customer is not a slogan, nor a way of saying at Tassullo: it is a choice . A choice strengthened by constant research and development of the best solutions in the field of construction, but most of all by a widespread presence of our establishments, our logistic centres, our laboratories and our service centers all over the territory. We have chosen this path because we firmly believe that to be close to our customers means to be present in the territory with staff, infrastructures and resources.

Establishment TASSULLO (TN)

research center

Establishment MOLLARO (TN)

TASSULLO (TN)

research center BRANCH OF BUCAREST

Establishment SOLFERINO (MN) Establishment OZZANO (AL)

Establishment BUCAREST

3 1 - Customer service 2 - Technical assistance on the construction sites 3 - Establishments

Tassullo Research Center

Establishment of Solferino

Via Nazionale 157, Tassullo (TN) - Italy

Via Napoleone III 110,

Research Center

Solferino (MN) - Italy

Branch of Bucarest,

Establishment of OZZANO

Bolintin Deal - Romania

Via Rivara 5,

Tassullo Establishment

Ozzano Monferrato (AL) - Italy

Via Nazionale 157, Tassullo (TN) - Italy

Establishment of BUCAREST

Establishment of Mollaro

Highway Bucuresti- Pitesti, Km 23

Via alla Miniera 1,Taio (TN) - Italy

Bolintin Deal - Romania

We live side by side with our customers 6 12

Choose Tassullo because our strong point is the consideration of each detail even during production.

At Tassullo we always aim to improve our strong points. We have quality ,effective and eco-compatible products that have a high performance but we always aim to obtain the best results. Our production begins in special environments, that have a very high technology with advanced machinery and highly skilled staff. This allows us to develop unique and innovative solutions for the building industry as the new Tassullo CLEAN SACK. In fact Tassullo uses a revolutionary method of packaging the product that guarantees the hermetic sealing through a thermo- welding system that avoids the dispersion of the product during movements. To have a Tassullo CLEAN SACK means to have a cleaner environment.

From the single sack to the pallet,.Tassullo has sealed the products hermetically to protect them from bad weather and guarantee cleanliness in the working environment

NEW: Tassullo Clean Sack

A detail of the â&#x20AC;&#x153;Clean Sackâ&#x20AC;? production

We test and develop the best productive technologies 14

Choose Tassullo because it means that quality is certified in all aspects: customer, environment and safety.

The certificates that Tassullo has obtained testify the determination of the intense commitment to achieve high quality product standards and a constant focus towards man and the environment. Tassullo has certified its Health System and Industrial Safety (BS OHSAS 18001), its management quality System (EN ISO 9001) and its Environmental Management System (EN ISO 14001), in order to always guarantee the best for its partners and its customers. At Tassullo the entire productive process respects the most severe environmental regulations and the highest international safety standards for those who work in the productive phase and for those who will use the product. We have certified our reliability, consistency and safety. Choose Tassullo because it means that quality is certified in all aspects: customer, environment and safety.

Tassullo Research Center: the territory

We have certified our reliability, consistency and safety 16

Choose Tassullo because it is synonymous with Green Company. The values of social and environmental responsibility have always been part of our philosophy: the protection of man and its environment, the care and choice of materials, the use of clean energy deriving from

All these elements make Tassullo a “Green Company”, that is a company whose roots are based in a real culture that respects and cares about the environment in which it operates. For a long time Tassullo has been one of the few companies in this sector that could be proud about its Environmental Certification ISO 14001. This result was strongly desired because it represents the great consideration that Tassullo has towards the environment and this is one of the founding values of Tassullo’s corporate culture.

renewable sources, the environment-oriented waste management and waste production management, the reduction of gas emissions into the atmosphere that are well beyond that provided by existing regulations and the total

TASSULLO is a partner CasaClima KlimaHaus®

clean energy

LEED

TASSULLO uses energy deriving from renewable sources

TASSULLO is the founder member of CBC Italia

elimination of emissions into water.

Tassullo Research Center: the environmental context

Nature is always in our DNA 18

Reficere: an Editorial Collection that publishes the results of Tassullo Research.

The daily cooperation with influential University professors and some of the major experts in design and applied research, has contributed in creating the Scientific Reficere Collection. Pubblished by Electa Mondadori ,it has reached the 8th volume. The Reficere Collection becomes a fundamental instrument in order to publish the results of the most advanced researches in the field of restoration and artistic heritage restoring on a large scale.

Reficere is Tassullo’s editorial project

The International Scientific Reficere Committee: Luigia Binda (Politecnico di Milano – Italia), Dina D’Ayala (University of Bath – UK), Miloš Drdácký (Academy of Science of Czech Republic - Czech Republic), Andrea Fuganti (Università di Trento – Italia), Paulo Lourenço (University of Minho, – Portugal), Christiane Maierhofer (Federal Institute for Materials Research and Testing (BAM) – Germany), Claudio Modena (Università di Padova – Italia), Pere Roca (Universitat Politècnica de Catalunya, Barcelona – Spain), Cesare Renzo Romeo (Politecnico di Torino II Facoltà di Architettura – Italia), Miha Tomaževia (Slovenia National Building and Civil Engineering Institute (ZAG), Ljubljana – Slovenia), Koen Van Balen (Katholieke Universiteit Leuven – Belgium), Elizabeth Vintzileou (National Technical University of Athens – Greece). 20

Tassullo’s experience in the field of restoration and artistic heritage restoring 21

To choose Tassullo means to rely on a quality brand.

Tassullo is present at the most important fairs in this sector. (Photo: KlimaHouse 2010 - Bolzano)

Tassullo organizes and sponsors technical and cultural meetings together with professional associations.

Sponsorship from the sidelines during matches of the Italian national football team and during the final of the Italian Cup live on national television networks.

Communication 22

a of Gard i, Baths r d e C f Villa o R) - Italy azise (V L i d lĂ Co

Residen tial buil ding Thiene (VI) - Ita ly

Corte Paradiso Peschiera del Ga rd

a (VR) - Italy

) - Italy

(PN ordenone -Haus â&#x20AC;&#x201C; P

otel Art H VA) - Italy e( Vares Villa Fastig gi District Pesaro (PU ) - Italy

Some references 24

San Nic eto cas tle Reggio Calabr ia (RC) - Italy

church San Nicola N) - Italy Farigliano (C

Arena plot site Verona (VR) - Italy

Peace Tower Ottaw a - Ca nada

castle Dover d Englan

Residenti al buildin g Bucarest, Romania

nument Aviator mo omania Bucarest, R

Some references 26

urch Ortodox ch - Belgium Chevetogne

Marchesato Pallavicino castle Arenzano (GE) - Italy

ding urroun Italy s l l a W I) tica (V Maros

NEW BUILDINGS

HYSTORICAL BUILDINGS

NATURAL BUILDINGS

CONCRETE BUILDINGS

Construction and renovation of buildings in compliance with bio-architecture: farmsteads, farmhouses and buildings built following Leed and Casaclima criteria

Renovation of residential, industrial, multipurpose reinforced concrete buildings

MASONRIES AND PARTITIONS

BINDERS

CONSOLIDATION AND RESTORATION

Building and renovation of residential, industrial and multipurpose buildings

»» mortars »» plasters »» exposed surface mortars »» special mortars

Renovation and recovery of historical buildings, historical sites, buildings protected and regulated by Environmental and Architectural Heritage Agencies

p. 36 p. 37 p. 41 p. 44

FINISHING AND LEVELING »» top coat plasters »» interior finishing »» exterior finishing

p. 45 p. 47 p. 48

»» NHL5 natural hydraulic lime »» NHL 3.5 light natural hydraulic lime »» lime putty

p. 66 p. 67 p. 67

CONSOLIDATION »» consolidation injection mixture »» consolidating rendering grout »» fiber-reinforced lightweight grout »» quick drying mortar for renovation and safety measures

p. 68 p. 68 p. 69 p. 69

SEALING MORTAR

FLOORS »» special binders for floor screeds »» floor screeds »» bonding adhesives »» self-smoothing leveling

p. 50 p. 52 p. 54 p. 56

THERMAL INSULATION »» thermal plaster »» top coat plasters »» finishing »» cladding bonding agents »» polystyrene plate cladding

p. 56 p. 58 p. 58 p. 59 p. 60

»» sealing and exposed surface-masonry mortar »» colored sealing mortar as per sample

p. 70 p. 70

PLASTERS »» machine applied plaster »» plastering mortar »» fiber reinforced plastering mortar »» breathable waterproof plastering mortar

p. 71 p. 72 p. 72 p. 73

»» NHL5 natural hydraulic lime »» lime putty

p. 82 p. 82

MASONRIES AND PARTITIONS »» mortars »» plasters

p. 83 p. 84

FINISHING AND LEVELING »» top coat plasters »» finishing

p. 85 p. 85

FLOORS »» floor screeds »» bonding agents

p. 86 p. 87

THERMAL INSULATION

p. 92 p. 92 p. 93 p. 93 p. 94 p. 94

FASTENING AND RECONSTRUCTION »» high resistance quick drying mortar for fastening and reconstructions

p. 95

WATERPROOFING

»» thermal plaster »» cladding in natural cork

p. 87 p. 88

»» dual component waterproof leveling

p. 95

PROTECTIVE SYSTEM »» passivating grout

FINISHING AND LEVELING »» extra fine, fine, medium and coarse fine top coat plaster/primer »» extra fine, fine, medium and coarse white top coat plaster »» fine, medium and coarse waterproof finishing »» breathable waterproof finishing in natural hydraulic lime

»» fiber-reinforced mortar for light structural concrete (LCS) restoration »» casting mortar for filling »» passivating fiber-reinforced mortar for the restoration of steel bar covers »» anti-carbonation top coat plaster for reinforced concrete structures »» protective painting for reinforced concrete structures »» corrosion inhibitor

p. 96

THERMAL INSULATION »» thermal insulating plaster »» expanded polystyrene thermal insulation system »» mineral wool thermal insulation system

p. 73 p. 74 p. 74

p. 96 p. 97 p. 97

p. 75

DEHUMIDIFICATION AND WATERPROOFING »» breathable waterproof plastering mortar »» reclaiming dehumidifying cycle

p. 75 p. 76

STONE ELEMENTS RECONSTRUCTION »» product for the reconstruction of stone elements

p. 77

THERMAL INSULATION »» natural thermal plaster

PRODUCT DATA SHEET > page 32

p. 77

PRODUCT DATA SHEET > page 62

PRODUCT DATA SHEET > page 78

PRODUCT DATA SHEET > page 90

Our high quality solutions 28

ENERGY SAVING

WOOD HOUSES

ADVANCED SYSTEMS

CLADDING SYSTEMS

WALL SYSTEM

FIREPROOFING

Special products for the construction of wood houses

Products and solutions for the thermal insulation of all types of buildings

»» thermal insulation system in natural cork »» mineral wool thermal insulation system »» calcium silicate thermal insulation system »» Wood fiber thermal insulation system »» expanded polystyrene thermal insulation system

p. 101 p. 101 p. 102 p. 102 p. 102

BONDINGS - TOP COAT PLASTERS FOR CLADDING SYSTEM »» bonding /top coat plaster for expanded polystyrene plate »» bonding/ top coat plaster with medium particle size for eps plates »» lightweight bonding / top coat plaster for plate claddings »» high breathability bonding / top coat plaster in NHL5 lime »» high breathability lightweight bonding / top coat plaster in NHL5 lime »» bonding / top coat plaster in BIO-E NHL 5 natural hydraulic lime

p. 103 p. 103 p. 103 p. 103

»» top coat plasters »» plasters »» protective agents »» primer

Products and solutions for fireproofing, waterproofing and quick line marking repairs

p. 112 p. 112 p. 113 p. 113

FLOORING SYSTEM »» floor screeds »» sub-base thermal insulating lightweight floor screed »» quick drying floor screed »» low thickness floor screed »» self-leveling top coat plaster »» professional adhesive for interiors

p. 114 p. 114 p. 115 p. 115 p. 116 p. 116

»» protective coating for the passive protection of steel structures »» fireproof expanding product »» fireproof coating for cable duct sealing »» fireproof masonry plaster »» fireproof mobile barrier

p. 120 p. 121 p. 121 p. 122 p. 122

WATERPROOFING »» dual component waterproof leveling

p. 124

LINE MARKING REPAIRS »» finishing-ready and quick-drying mortar for line marking repairs

p. 126

THERMAL INSULATION »» wooden fiber thermal insulation system

p. 117

p. 103 p. 103

THERMAL PLASTERS AND MORTARS »» thermal insulating mortar »» infilling thermal insulating mortar »» thermal insulating plaster »» natural thermal insulating plaster

p. 105 p. 105 p. 106 p. 106

PRODUCT DATA SHEET > page 98

PRODUCT DATA SHEET > page 108

PRODUCT DATA SHEET > page 118

Our high quality solutions 30

mortars _T200 _T300 _T-SPAN plasters _T200 _T300 _T501 _TL84 _TL97 _T-cream _T5OS _T5FB _TLTX exposed surface mortars _T170-P _T170-PS _T270-P _T270-PS _T-BLOCK special mortars _T-FLASH _T192 D

2 - FINISHING AND LEVELING

top coat plasters _T-MULTI/sf, sg _T-SPAN _TBØØ/TBØ1/TBØ2/TBØ4 interior finishing _TF1000 _Grassello _TRG/03 exterior finishing _T600-00 _T600-01 _Tassullo finishing

3 - FLOORS

special binders for floor screeds _MIXTO PAVI _MIXTO PAVI B _MIXTO PAVI R floor screeds _PAVI/1 _MASSETTO _T48S/N _T48S/B bonding adhesives _T-Fix _T-Fix IE _T-Fix Flex _T-Fix HP self-smoothing leveling _T-LIVEL

NEW BUILDINGS NEW BUILDINGS

1 - MASONRY AND PARTITIONS

4 - THERMAL INSULATION

thermal plaster _TERMO-TASS top coat plasters _TAØ2 finishing _Tassullo finishing cladding bonding agents _TK01/gr, bn _ISI-FISS polystyrene plate cladding _ISI-THERM system

Neighborhood of Villa Fastiggi Pesaro (PU) - Italy

Building and renovation of residential, industrial and multipurpose buildings

The living space is important, for those who design it, for those who build it, and especially for those who live in it. Tassullo strived to design materials capable of achieving the best solutions for the construction of residential, industrial and multi-purpose buildings. Those who design a living space must have available the best technical solutions, those who build it must work in safety and with ease, and those who live in it must experience maximum comfort and safety.

PRODUCT DATA SHEET > 32

T200

MASONRY SYSTEM

T300

ISI-FISS T-cream T-ISI Plate TF1000

mesh

MASONRY SYSTEM IN CALCIUM SILICATE BLOCKS 5

T-SPAN T-SPAN

FLOOR SYSTEM

T-FIX IE T48S/N

NEW BUILDINGS

CLADDING SYSTEM

PAVI/1

ISI-FISS Tassullo finishing

LCS MASONRY SYSTEM

T-MULTI T-FIX FLEX

T501

IDROTASS TAØ1

EXPOSED SURFACE MASONRY SYSTEM

IDROTASS T-FIX

Tassullo finishing T270-P

T-FIX HP

NEW BUILDINGS Systems and applications 34

NEW BUILDINGS

NEW BUILDINGS MASONRIES AND PARTITIONS

T200

HIGH WORKABILITY BEDDING MORTAR AND MANUAL PLASTER

MORTARS

TECHNICAL CHARACTERISTICS: T200 is a bedding mortar that can be pumped right at the building yard, containing up to 2 mm of hydraulic binders and aggregates, completely free from organic substances and featuring granulometry that allows high workability, outstanding flow ability and ease of application to the mix. T200 is available in M5 and M10 resistance classes in accordance to UNI EN 998-2 standards for masonry mortars. If used as plaster, the T200 is compliant to UNI EN 998-1.

T-SPAN

BONDING/LEVELING MORTAR FOR CALCIUM SILICATE BLOCKS

MORTARS

NEW BUILDINGS

MASONRIES AND PARTITIONS

TECHNICAL CHARACTERISTICS: T-SPAN is a bonding/leveling agent constituted by natural hydraulic lime, selected aggregates featuring a maximum granulometry of 0.8 mm, and additives. Used as a leveling agent, it allows ease of application and excellent characteristics of adhesion and elasticity. FIELD OF APPLICATION: T-SPAN has been designed specifically for use as a low thickness bedding mortar for calcium silicate block masonries and their surface leveling agent.

FIELD OF APPLICATION: T200 is a mortar suitable for the application of masonry, renders, and conventional plasters. It is used as a bedding mortar or as a conventional plaster on all types of bricks where the use of hydraulic binder mortars is allowed. T200 is supplied in silos through a mixing auger or pneumatic conveyor system to the work surface. This preparation system simplifies the organization of the building yard by eliminating the dead time required to transport the mortar to the work surfaces.

ADVANTAGES: - high adhesion also to low absorption and smooth surfaces - it can be used as top coat plaster on light structural concrete (LSC), drywall, and fiber panels in concrete or concrete wood, waterproof plaster etc. - it can be used as an adhesion promoting primer on concrete - compatible with the use of fiberglass reinforced meshes

ADVANTAGES: - conveyable to the work surfaces through a pneumatic system - certified mechanical strength - easy to apply - high workability

HOW TO APPLY IT: T-SPAN must be applied to clean supports, free from uneven elements, dusts, oil, salt efflorescence, soot, organic compounds, mold etc. MIXING WATER: 0.23 liters/kg (approx. 7liters/sack)

HOW TO APPLY IT: T200 can be applied manually or through a plastering machine suitable for conventional plaster, which performs the automatic dosing of water and pumps out the mixed material.

YIELD: consumption for calcium silicate blocks bedding is 5 ÷ 7 kg/m2 (for 25 cm thick blocks) PACKAGE: 25 kg sack or loose in silos equipped with mixing auger

MECHANICAL RESISTANCE (REF. UNI EN 908-2): T200 > 5 n/mm²; T200M10: >10 n/mm² MIXING WATER: 0.17 liters/kg (approx. 5 liter/sack) YIELD: approximate consumption for partition: 12 cm: approx. 12 kg/m² PACKAGE: 30 kg sack or loose in silos equipped with mixing auger

certified mechanical strength

conveyable to the work surfaces through a pneumatic system

MASONRIES AND PARTITIONS

MASONRIES AND PARTITIONS MORTARS

BEDDING MORTAR AND MANUAL PLASTER

T300

MACHINE PLASTER

T501

CONVENTIONAL PLASTER

TECHNICAL CHARACTERISTICS: T300 is a mortar completely free from organic substances characterized by excellent workability and strong adhesion to the surface. T300 is available in M5 and M10 resistance class in accordance to UNI EN 998-2 standards for masonry mortars. If used as a plaster, T300 is compliant to UNI EN 998-1.

TECHNICAL CHARACTERISTICS: T501 is a ready to use plaster in natural hydraulic lime and selected aggregates, ideal for the preparation of traditional breathable plasters. T501 is compliant to UNI EN 998-1 “Specifications for mortar for masonry – interior and exterior plaster mortars" and it is subject to CE marking in accordance to the regulations in force.

FIELD OF APPLICATION: T300 is a mortar suitable for the application of masonry, renders, and conventional plasters designed to replace conventional mortar in full. It is used as a bedding mortar or as a conventional plaster on all types of bricks where the use of hydraulic binding mortars is allowed.

FIELD OF APPLICATION: T501 is applicable for interiors and exteriors in 15/20 mm layers, on any even surface, smooth, and dry surface.

ADVANTAGES: - certified mechanical strength - high workability HOW TO APPLY IT: T300 can be applied manually or through a plastering machine suitable for the application of material with granulometry up to 4 mm max. MIXING WATER: 0.15 liters /kg (approx.4.5 liters/sack)

ADVANTAGES: - breathable, it hinders the formation of molds - high spreadability and plasticity - long workability - high adhesion - for interiors and exteriors HOW TO APPLY IT: the mix is applied using continuous spray plastering machines that automatically dose the water in the mix without adding other binders or aggregates. T501 offers a long workability, it can be finished at will using a post, American trowel or sponge and it is suitable for several architectural solutions.

MECHANICAL RESISTANCE (REF. UNI EN 908-2): T300 > 5 n/mm²; T200M10: >10 n/mm² MIXING WATER: 0,21 liters/kg (approx. 6.5 liters/sack)

YIELD: 34x24x25=23 kg/m² - 34x24x30=27 kg/m²

YIELD: approx.13.5 kg/(m² x cm)

PACKAGE: 30 kg sack and loose in silos

PACKAGE: 25 kg sack or loose in silos

high plasticity

certified mechanical strength

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

high adhesion

high spreadability

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

NEW BUILDINGS

NEW BUILDINGS MASONRIES AND PARTITIONS

TL84

LIGHTWEIGHT PLASTER FOR HIGH YIELDS

MACHINE PLASTER

TECHNICAL CHARACTERISTICS: T-cream is a plaster in natural hydraulic lime, selected aggregates and cellulose characterized by easy prop up and a high degree of finishing. It is compliant to UNI EN 998-1 “Specifications for mortar for masonry – interior and exterior plaster mortars”.

TECHNICAL CHARACTERISTICS: TL84 is a lightweight plaster in natural hydraulic lime, aggregates and carefully selected perlite. It has been designed to provide high yields. TL84 is the ideal product whenever obtaining a high hourly production without sacrificing quality is required. TL84 is compliant to UNI EN 998-1 "Specifications for mortar for masonry – interior and exterior plaster mortars" and it is subject to CE marking in accordance to regulations in force.

FIELD OF APPLICATION: T-cream is applicable on any even surface, smooth and dry surface, as long as it is free from dust, salts, molds, uneven elements etc. It allows applying plaster on vertical walls and ceilings in 10/15 mm layers.

FIELD OF APPLICATION: TL84 can be applied to any even interior and exterior surface. It allows applying plaster on vertical walls and ceilings in 15/20 mm layers. ADVANTAGES: - high yield - plasticity - high adhesion

ADVANTAGES: - high spreadability and plasticity - high adhesion - quick finishing - for interiors and exteriors

HOW TO APPLY IT: the mix is applied using continuous spray plastering machines that automatically dose the water in the mix without adding other binders or aggregates. TL84 offers a long workability, it can be finished at will using a post, American trowel or sponge and it is suitable for several architectural solutions.

HOW TO APPLY IT: the mix is applied using continuous spray plastering machines that automatically dose the water in the mix without adding other binders or aggregates. It can be finished at will using a post, American trowel or sponge. MIXING WATER: 0.21 liters/kg (approx. 6.5 liters/sack)

MIXING WATER: 0.21 liters/kg (approx. 6.5 liters/sack)

YIELD: approx. 12 kg/(m²x cm)

YIELD: approx. 12.5 kg/(m²x cm)

PACKAGE: 30 kg sack or loose in silos

high yield

quick finishing

high adhesion

MASONRIES AND PARTITIONS MACHINE PLASTER

high yield

quick finishing

high plasticity

MASONRIES AND PARTITIONS

TL97

FIREPROOF PLASTER

TECHNICAL CHARACTERISTICS: TL97 is a fireproof plaster in natural hydraulic lime and selected lightweight aggregates characterized by excellent yield and ease of application. TL97is compliant to UNI EN 998-1 "Specifications for mortar for masonry – interior and exterior plaster mortars” and it is subject to CE marking in accordance to regulations in force. TL97 when applied to non-bearing walls in perforated brick adds fireproof resistance to it allowing the wall to be classified as REI 120 (ref. CSI Certificate No. CSI1108RF dated 02/18/2004). FIELD OF APPLICATION: TL97 can be applied to any even surface. Its low density offers plaster ease of application and spreading to the wall, which optimizes yield and hourly production while maintaining high quality standards; TL97 can be applied both in interiors and exteriors and it allows applying plasters on vertical walls and ceilings in 15/20 mm layers. ADVANTAGES: - fireproof (class REI 120) - high yield and workability HOW TO APPLY IT: TL97 must be applied to clean supports, free from uneven elements, dust, oil, salt efflorescence, soot, organic compounds, mold etc.

MACHINE PLASTER

WATERPROOF PLASTER

T50S

TECHNICAL CHARACTERISTICS: T50S is a waterproof plaster in natural hydraulic lime and 0 to 1.4 mm selected aggregates. T50S has a high resistance to water absorption combined with the breathability of traditional natural hydraulic lime. T50S is compliant to UNI EN 998-1 "Specifications for mortar for masonry – interior and exterior plaster mortars" and it is subject to CE marking in accordance to regulations in force. FIELD OF APPLICATION: T50S allows creating plasters with low water absorption to be applied to vertical walls that are exposed to the weather as well as to walls under renovation that were deteriorated by rising moisture. The use of T50S is recommended as an exterior plaster to be manually applied in a single coat with a thickness of 15/20 mm. ADVANTAGES: - waterproof - durable - healthy - more dimensionally stable

MIXING WATER: 0.21 liters/kg (approx. 6.5 liters/sack)

HOW TO APPLY IT: the mix is applied using continuous spray plastering machines that automatically dose the water in the mix without the need to add other binders or aggregates. It can be finished at will using a post, American trowel, or sponge.

FIREPROOF CLASS: REI 120 – REI 180 (on 8 cm brick flat tile)

MIXING WATER: 0.21 liters/kg (approx. 6.5 liters/sack)

YIELD: approx. 12 kg/(m²x cm)

YIELD: approx. 13 kg/(m²x cm)

CLASS REI 120 REI 180

PACKAGE: 30 kg sack or loose in silos equipped with mixing auger high yield

high workability

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

T-cream

HIGH WORKABILITY PLASTER

MACHINE PLASTER

NEW BUILDINGS

MASONRIES AND PARTITIONS

fireproof class REI 120

WATER ABSORPTION: class W2 (UNI EN 1015-18) PACKAGE: 30 kg sack or loose in silos

CSI CERTIFICATE

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

NEW BUILDINGS

NEW BUILDINGS MASONRIES AND PARTITIONS

MACHINE PLASTER

T5FB

FIBER REINFORCED PLASTER

EXPOSED SURFACE MORTARS

EXPOSED SURFACE MASONRY MORTAR

T170-P

TECHNICAL CHARACTERISTICS: T5FB is a fiber reinforced plaster in natural hydraulic lime and carefully selected aggregates and it is compliant to UNI EN 998-1 “Specifications for mortar for masonry – interior and exterior plaster mortars" and it is subject to CE marking in accordance to the regulations in force.

TECHNICAL CHARACTERISTICS: T170-P is a mortar in natural hydraulic lime with a maximum granulometry of 0.6 mm, suitable for application to exposed surface solid brick. T170-P is compliant to UNI EN 998-2 and subject to CE marking.

FIELD OF APPLICATION: T5FB can be applied both for interiors and exteriors. Its ease of application, high yield, thixotropy and fiber reinforcement allow applying it to supports that are not perfectly even or flat and that require different plaster thicknesses (10/25 mm). T5FB allows applying plasters to vertical walls and ceilings in 15/25 mm layers.

FIELD OF APPLICATION: T170-P is designed to obtain mortars with special joining layer finishes both from a physical and chromatic point of view. It can be applied to any solid brick.

ADVANTAGES: - fiber-reinforced and resistant - easy to apply - for demanding surfaces HOW TO APPLY IT: T5FB can be finished at will using a post, American trowel or sponge; it is suitable for several architectural solutions. Once cured, T5FB is able to bear any type of two coat finishing, finishing or painting.

NEW BUILDINGS

MASONRIES AND PARTITIONS

ADVANTAGES: - excellent aesthetical yield - uniform and even when applied - certified mechanical strength HOW TO APPLY IT: T170-P is applied manually in accordance to standard methods of application to exposed surface bedding mortars. MIXING WATER: 0.18 liters/kg (approx. 5.5 liters/sack)

COMPRESSION STRENGTH (UNI EN 1015-11): CS II ( 1,5 ÷ 5 N/mm2)

YIELD: consumption per brick 24x11x6 cm - approx. 30 kg/m²

YIELD: approx.13,5 Kg/(m2 x cm)

PACKAGE: 30 kg sack or loose in silos equipped with mixing auger

MIXING WATER: 0,21 l/Kg (approx. 6,5 l/sack) PACKAGE: 30 kg sack or loose in silos

fiber reinforced plaste

easy to aplly

for demanding surfaces

MASONRIES AND PARTITIONS ACRYLIC EMULSION

MASONRIES AND PARTITIONS PRIMER AND STRENGTHENING MILK FOR PLASTERS

TLTX

EXPOSED SURFACE MORTARS

WATERPROOF MORTAR FOR EXPOSED SURFACE MASONRIES

T170-PS

TECHNICAL CHARACTERISTICS: TLTX is a special acrylic emulsion in water, resistant to alkali and to the weather, compatible with air and hydraulic binders normally used in construction (air lime, hydraulic lime, cement etc.).

TECHNICAL CHARACTERISTICS: T170-PS is a waterproof mortar in natural hydraulic lime with a maximum granulometry of 0.6 mm, suitable for application to exposed surface solid brick. T170-PS is compliant to UNI EN 998-2 and subject to CE marking.

FIELD OF APPLICATION:TLTX is suitable for the construction of fixative primers and strengthening primers on existing plasters, lime-based finishing, floor screeds, or to increase the priming capacity, elasticity and abrasion resistance of lime or cement based mortars or plasters.

FIELD OF APPLICATION: T170-PS is designed to obtain mortars with special joining layer finishes both from a physical and chromatic point of view. It can be applied to any solid brick. The low water absorption limits the risk of salt efflorescence.

ADVANTAGES: - free from organic solvents - versatile

ADVANTAGES: - waterproof - it limits the risk of salt efflorescence - excellent aesthetical yield - uniform and even when applied

HOW TO APPLY IT: TLTX can be applied by roller or brush on any dry and clean surface. When added to plastering mortars, finishing or floor screeds, it does not modify the usual processing methods of the related products. YIELD: approx. 0.2 kg/m²

HOW TO APPLY IT: T170-PS is applied manually in accordance to standard methods of application to exposed surface bedding mortars.

CONSUMPTION WHEN ADDED TO PLASTERING MORTAR: up to 5% on dry material

MIXING WATER: 0.18 liters/kg (approx. 5.5 liters/sack)

PACKAGE: 5 liters can

YIELD: consumption per brick 24x11x6 cm - approx. 30 kg/m² PACKAGE: 30 kg sack or loose in silos equipped with mixing auger

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

NEW BUILDINGS

NEW BUILDINGS MASONRIES AND PARTITIONS

EXPOSED SURFACE MORTARS

EXPOSED SURFACE MASONRY MORTAR

T270-P

EXPOSED SURFACE MORTARS

WATERPROOF MORTAR FOR EXPOSED SURFACE MASONRIES

T270-PS

TECHNICAL CHARACTERISTICS: T270-P is a mortar in natural hydraulic lime with aggregates featuring a maximum granulometry of 2 mm, suitable for application to exposed surface solid brick. T270-P is compliant to UNI EN 998-2 and subject to CE marking.

TECHNICAL CHARACTERISTICS: T270-PS is a mortar in natural hydraulic lime with aggregates featuring a maximum granulometry of 2 mm, suitable for application to exposed surface solid brick. T270-PS is compliant to UNI EN 998-2 and subject to CE marking.

FIELD OF APPLICATION: T270-P is designed to obtain mortars with special joining layer finishes both from a physical and chromatic point of view. It can be applied to any solid brick.

FIELD OF APPLICATION: T270-PS is designed to obtain mortars with special joining layer finishes both from a physical and chromatic point of view. It can be applied to any solid brick. Its low water absorption limits the risk of salt efflorescence.

ADVANTAGES: - excellent aesthetical yield - uniform and even when applied - certified mechanical strength HOW TO APPLY IT: T270-P is applied manually in accordance to standard methods of application to exposed surface bedding mortars.

NEW BUILDINGS

MASONRIES AND PARTITIONS

ADVANTAGES: - waterproof - lowers the risk of salt efflorescence - excellent aesthetical yield - uniform and even when applied

MIXING WATER: consumption per brick 24x11x6 cm - approx. 30 kg/m²

HOW TO APPLY IT: T270-PS is applied manually in accordance to standard methods of application to exposed surface bedding mortars.

YIELD: 0.18 liters/kg (approx. 5.5 liters/sack)

MIXING WATER: 0,18 l/Kg (approx. 5,5 l/sack)

PACKAGE: 30 kg sack or loose in silos equipped with mixing auger

YIELD: consumption per brick 24x11x6cm - ca. 30 Kg/m2 PACKAGE: 30 kg sack or loose in silos

certified mechanical strength

excellent aesthetical yield

MASONRIES AND PARTITIONS EXPOSED SURFACE MORTARS

MORTAR FOR EXPOSED SURFACE CONCRETE BLOCKS

T-BLOCK

TECHNICAL CHARACTERISTICS: T-BLOCK/GR,BN is a waterproof mortar containing hydraulic binders and aggregates with a granulometry up to 2 mm, characterized by excellent workability and surface finishing. It can be supplied in grey (GR) or white (BN) hues, according to the chromatic requirements of the type of brick used. T-BLOCK/GR,BN is available in M5 and M10 classes, according to UNI EN 998-2. FIELD OF APPLICATION: T-BLOCK/GR,BN is designed for bedding and seeping of waterproofed exposed surface concrete blocks and expanded clay blocks. ADVANTAGES: - resistant - waterproof - designed for expanded clay blocks and LSC (light structural concrete) HOW TO APPLY IT: T-BLOCK/GR,BN is applied to clean blocks, free from uneven elements. After applying it, the flow of exposed mortar is suitable for finishing using flat or hollow tools in order to obtain a compact grouting profile. MIXING WATER: 0.18 liters/kg (approx. 5.5 liters/sack) DENSITY (dry mortar): 1800÷1900 Kg/m3 COMPRESSION STRENGTH (UNI EN 1015-11): class M5: (5 ÷ 10 N/mm²) PACKAGE: 30 kg sack or loose in silos equipped with mixing auger.

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

NEW BUILDINGS

NEW BUILDINGS MASONRIES AND PARTITIONS LINE MARKING AND HOLES FILLING QUICK MORTAR

SPECIAL MORTARS

INFILLING THERMAL MORTAR

SPECIAL MORTARS

T192D NEW BUILDINGS

MASONRIES AND PARTITIONS

TECHNICAL CHARACTERISTICS: T192D is a thermal insulated mortar characterized by a thermal conductivity comparable to the one of porous bricks used in construction. T192D is compliant to UNI EN 998-1 and it is subject to CE marking in accordance to regulations in force. T192D is compliant to Italian Ministerial Decree 10/05/2004 and it is available in CSII resistance class, in accordance to UNI EN 998-1 for plastering mortars.

TECHNICAL CHARACTERISTICS: T-FLASH is a mortar with high plasticity and quick drying (approx. 20 minutes), specifically designed to repair electrical marking, hydraulic marking and holes; its quick drying makes T-FLASH immediately suitable for finishing. FIELD OF APPLICATION: T-FLASH is ideal for filling and repairing line marking or holes on brick masonry, concrete, existing hydraulic binder plasters, drywalls etc. caused by the passage of electrical or hydraulic systems. Setting and hardening speed as well as the product workability allow filling in a single coat and finishing in a few minutes.

FIELD OF APPLICATION: T192D is a thermal insulated mortar for filling and repairing line marking or holes. It is particularly suitable in construction of porous brick masonries whenever avoiding the presence of heat bridges and reducing the theoretical insulation capacity of the block, due to the filling of the line marking with conventional plaster, is desired.

ADVANTAGES: - immediate finishing - non shrinkable - it does not cause unaesthetic cracks - it allows considerable thickness in a single coat - packaged in a sealed sack

ADVANTAGES: - highly insulating - high workability

HOW TO APPLY IT: T-FLASH is applied manually using a spatula or trowel, paying attention to fill the edges first and then the whole line marking.

HOW TO APPLY IT: T192D can be applied manually, as if applying a conventional plastering mortar, or it can be applied using a plastering machine for premixed plaster. The product plasticity and workability allow achieving a significant thickness in just one coat (up to 10 cm).

MIXING WATER: approx. 2 liters/10 kg sack

YIELD: approx. 16 kg/(m²x cm)

YIELD: approx. 7 kg/(m²x cm)

PACKAGE: 10 kg and 30 kg sacks

THERMAL CONDUCTIVITY (EN 1745:2002): 0,2 W/(m x °K)

CLEAN SACK: the quality of T-FLASH is guaranteed by a double seal: both sack and pallet are sealed. This allows not soiling the area when handling the sack, especially when the work takes place inside occupied houses or apartments.

PACKAGE: 18 kg sack or loose in silos equipped with mixing auger

FINISHING AND LEVELING

T-FLASH USAGE

TOP COAT PLASTERS

TOP COAT PLASTER/PLASTER BONDING

T-MULTI/ sf, sg

TECHNICAL CHARACTERISTICS: T-MULTI is a top coat plaster/multipurpose primer in natural hydraulic lime, selected aggregates and cellulose, available in fine (SF – granulometry from 0 to 0.8 mm) or coarse (SG – granulometry from 0 to 1.4 mm) particle sizes in relation to the maximum granulometry of the included aggregate. FIELD OF APPLICATION: T-MULTI/sf,sg is used as a top coat plaster on any type of surface that does not allow for direct spreading of the finishing. T-MULTI/SF,SG is suitable as a top coat plaster on concrete, slab floors, calcium-silicate or magnesium wood panels, drywall, hydraulic binder plasters both new and existing, and whenever it is necessary to level a surface consisting of rough plaster of different nature and aging. T-MULTI/SG is also suitable as an adhesion bridge rendering on smooth or very absorbent surfaces (e.g. concrete), in anticipation of the completion of the base plaster. Hydraulic and electrical marking repairs

open line marking

Corner bead fastening

T-FLASH preparation

30’ 25 20 15

T-FLASH application

30’ 5

20 15

Corner bead finishing

smoothing and scraping

30’ 5

20 15

application finishing

30’ 5

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

closed line marking possible to polish

30’ 5

ADVANTAGES: - versatile - high adhesion - it contains natural hydraulic lime

Line marking repaired with T-FLASH

MIXING WATER: approx. 7 liters/30 kg sack

30’ 5

5 10 15

HOW TO APPLY IT: T-MULTI/sf,sg must be applied using a plastic or metal trowel and finished using a plastic or sponge plastering trowel depending on the granulometry and desired finishing degree. T-MULTI/SG used as an adhesion bridge must be sprayed by plastering machine.

YIELD: approx. 3-4 kg/(m²) PACKAGE: 30 kg sack

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

NEW BUILDINGS

FINISHING AND LEVELING

T-SPAN

INTERIOR FINISHING

FINE MORTAR

TF1000 NEW BUILDINGS

LEVELING/BONDING MORTAR FOR CALCIUM SILICATE BLOCKS

TOP COAT PLASTERS

TECHNICAL CHARACTERISTICS: TF1000 is a ready-to-use finishing in lime putty and selected aggregates with a maximum granulometry of 0.5mm for hydraulic binder-based two-coat plaster interior finishing.

TECHNICAL CHARACTERISTICS: T-SPAN is a bonding/top coat plaster in natural hydraulic lime, selected aggregates with a maximum granulometry of 0.8 mm and additives. Used as a leveling, it is easy to apply and it features excellent adhesion and elasticity characteristics.

FIELD OF APPLICATION: TF1000 is applied to interior air or hydraulic binder-based two-coat plasters (natural hydraulic lime, hydraulic lime, cement, air lime).

FIELD OF APPLICATION: T-SPAN has been designed specifically for use as a low thickness bedding mortar for masonries in calcium silicate blocks and as their surface leveling.

ADVANTAGES: - ready to use finishing - easy to apply

ADVANTAGES: - high adhesion also to low absorption and smooth supports - it can be used as top coat plaster on lsc, drywall, panels in concrete fiber or concrete wood, waterproof plasters etc. - it can be used as an adhesion promoter on concrete - compatible with the use of reinforced nets in fiberglass HOW TO APPLY IT: T-SPAN must be applied to clean supports, free from uneven elements, dust, oil, salt efflorescence, soot, organic compounds, mold etc.

HOW TO APPLY IT: TF1000 is applied by metal trowel to the base plaster making sure that the surface of the base is even and smooth so that it can be applied as an even and thin layer (<1 mm of thickness) to be finished later through sponge trowel. For application to exterior plasters, it is recommended the addition of TASSULLO natural hydraulic lime or TASSULLO TA00 or TB00 top coat plaster in percentages ranging from 5 to 10%.

MIXING WATER: 0.23 liters/kg (approx. 7 liters/sack)

YIELD: approx. 2 kg/m²

YIELD: consumption for flattening of calcium silicate blocks: 10÷15 kg/m²

PACKAGE: 25 kg sack

PACKAGE: 25 kg sack or loose in silos equipped with mixing auger

FINISHING AND LEVELING

FINISHING AND LEVELING TOP COAT PLASTERS

EXTRA FINE, FINE, MEDIUM, COARSE WHITE TOP COAT PLASTER

TBØØ/TBØ1 TBØ2/TBØ4

TECHNICAL CHARACTERISTICS: TB is a white top coat plaster available in four different granulometries (from 0.4 to 4 mm: TBØØ, TBØ1, TBØ2, TBØ4), suitable for leveling of all surfaces that are particularly difficult in terms of adhesion. FIELD OF APPLICATION: TB is used as a top coat plaster on all the types of support and in cases where it is necessary to level a surface consisting of rough plaster of different nature and aging. TB can be applied to any surface that requires a better base preparation for a subsequent finishing treatment. TB is compatible with the subsequent application of marmorinos, stuccos, plastic or mineral coatings. ADVANTAGES: - high adhesion capacity - solvents free - does not form a barrier to vapor - it can be left exposed HOW TO APPLY IT: TB is applied using a metal trowel and finished using a metal plastering trowel (sanding), plastic, sponge or other tools depending on the type and degree of desired finishing. It can be subsequently painted or left exposed. It is compatible with the subsequent application of a setting coat, putty, marmorinos, stuccos, plastic or mineral coatings, tiles, wallpaper, etc. It can include fiberglass meshes for the implementation of reinforced leveling on existing cracked plaster.

INTERIOR FINISHING

AIR BINDING PASTE

GRASSELLO

TECHNICAL CHARACTERISTICS: TASSULLO GRASSELLO is an air lime paste obtained from processing quicklime in a tank for over a month. TASSULLO GRASSELLO is compliant to UNI EN 459-1 "Building lime. Definitions, specifications and conformity criteria" classified as Cl-80 S and subject to CE marking according to regulations in force (Ref. On Austrian Standards Institute). FIELD OF APPLICATION: TASSULLO GRASSELLO can be used in addition to TASSULLO natural hydraulic lime or more in general to hydraulic lime or cement in the preparation of finishing or cement-lime mortar at the building yard. The addition of TASSULLO GRASSELLO to hydraulic mortar increases workability and plasticity. ADVANTAGES: certified YIELD: approx. 2 kg/m² PACKAGE: 25 kg sack in Big Bags, large case or pallets

MIXING WATER: 0.23 liters/kg (approx. 7 liters/sack) YIELD: 2÷3 Kg/m2 PACKAGE: 30 kg sack or loose in silos equipped with mixing auger

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

NEW BUILDINGS

NEW BUILDINGS FINISHING AND LEVELING GYPSUM BASED TOP COAT PLASTER FOR INTERIORS

INTERIOR FINISHING

TRG/03

TECHNICAL CHARACTERISTICS: T600-01 is a protective finishing in natural hydraulic lime, selected aggregates and natural origin cellulose with medium granulometry. T600-01 is suitable as a rough plaster finishing in natural hydraulic lime, hydraulic lime, or cement.

TECHNICAL CHARACTERISTICS: TRG/03 is a top coat plaster for interiors in hemi-hydrated gypsum, hydrated lime, selected aggregates and cellulose suitable for interior finishing resistant to abrasion. FIELD OF APPLICATION: TRG/03 is used to perform smooth finishing on interior gypsum-based plasters or hydraulic binders (hydraulic lime, cement). TRG/03 is applied as an interior top coat plaster on all common types of two coat plasters whether conventional or ready-mixed, applied manually or by plastering machine

FIELD OF APPLICATION: T600-01 is used as a finishing on all types of hydraulic binder-based rough plaster when it is necessary to increase the bonding coat and protection of the finishing respect to the finishing that can be achieved through a setting coat in lime putty. T600-01 can be subsequently painted or left exposed.

ADVANTAGES : - synthetic resin free - solvents free - it does not form a barrier to vapor - high resistance to abrasion

ADVANTAGES : - elastic - solvents free - it does not form a barrier to vapor - high mechanical strength

HOW TO APPLY IT: the mixed product is spread on the rough base plaster as long as it is clean, consistent, even, free from dust, salt efflorescence, molds, soot or other organic material, by using a metal trowel in one or two coats, with a maximum thickness of 2 mm. When it is dried, its smooth appearance will be achieved by sanding it with metal spatula loaded with a small amount of product in paste.

HOW TO APPLY IT: T600-01 is spread in a thin layer using a metal spatula and finished using a plastic, sponge, or wood trowel depending on the desired aesthetic effect. MIXING WATER: 0.23 liters/kg (approx. 7 liters/sack)

MIXING WATER: 0.6 liters/kg (approx. 15 liters/sack)

YIELD: 3 - 6 Kg/m2

YIELD: 1 Kg/m2

GRANULOMETRY: from 0 to 1.4 mm

PACKAGE: 25 kg sack

PACKAGE: 30 kg sack

FINISHING AND LEVELING EXTERIOR FINISHING

T600-01

WHITE PUTTY COAT FOR EXTERIOR FINISHING

EXTERIOR FINISHING

NEW BUILDINGS

FINISHING AND LEVELING

FINISHING AND LEVELING EXTERIOR FINISHING WHITE PUTTY COAT

T600-00

TECHNICAL CHARACTERISTICS: T600-00 is a protective finishing in natural hydraulic lime, selected aggregates and natural origin cellulose. T600-00 is suitable as a rough plaster finishing in natural hydraulic lime, hydraulic lime, or cement. FIELD OF APPLICATION: T600-00 is used as a finishing on all types of hydraulic binder-based rough plasters whenever it is necessary to increase the bonding coat and protection of the finishing respect to the finishing that can be achieved through a setting coat in lime putty. It can be subsequently painted or left exposed. ADVANTAGES : - elastic - solvents free - it does not form a barrier to vapor - high mechanical strength

EXTERIOR FINISHING

COLORED MINERAL FINISHING

Tassullo Finishing

TECHNICAL CHARACTERISTICS: TASSULLO mineral FINISHING are white and colored finishing for interiors and exteriors, made with natural materials such as hydraulic lime, hydrated lime and selected aggregates that are dry and ready-mixed with colored elements and natural pigments. Three different types are available: coarse, medium and fine granulometry. FIELD OF APPLICATION: it is used for white or colored mineral finishing on new or existing plasters, concrete, drywalls, and thermally insulated slab panels. ADVANTAGES : - natural - high aesthetic yield - durable

YIELD: 3 - 6 Kg/m2

HOW TO APPLY IT: TASSULLO FINISHING best chromatic and aesthetic results are achieved by applying the product to even and regular surfaces in a single and thin coat. It is recommended to use the following method of application: surfaces to be plastered: prepare the base plaster paying attention to troweling the surface evenly so as to create a smooth and evenly absorbent surface; to already plastered rough surfaces apply TASSULLO TA01 or TA02 top coat plaster with a spatula in order to allow the application of one coat of thin TASSULLO mineral finishings. TASSULLO mineral finishing can be finished using a plastic trowel or sponge, cloth or other tool depending on the finishing degree and desired aesthetic effect.

GRANULOMETRY: from 0 to 0.8 mm

MIXING WATER: 0,20 - 0,25 l/Kg (6 â&#x20AC;&#x201C; 7,5 l/sack)

PACKAGE: 30 kg sack

YIELD (e.g. with medium finishing): 3,5 Kg/m2

HOW TO APPLY IT: T600-00 is spread in a thin layer using a metal spatula and it is finished using a plastic, sponge, or wood trowel depending on the desired aesthetic effect. MIXING WATER: 0.23 liters/kg (approx. 7 liters/sack)

GRANULOMETRY: fine 0 - 0.8 mm / medium 0 - 2 mm / coarse 0 - 4 mm PACKAGE: 30 kg sack

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

NEW BUILDINGS

FLOORS

MIXTO PAVI

SPECIAL BINDING AGENTS FOR FLOOR SCREEDS

TECHNICAL CHARACTERISTICS: MIXTO PAVI is a special hydraulic cement binder for yard preparation of floor screeds for civil use with high workability and ready to walk on 24 hours after installation. It is compliant to UNI EN 413-1 and it is classifiable under class MC22, 5X. FIELD OF APPLICATION: MIXTO PAVI is added to 4/5 mm aggregate for the installation of substrates with a minimum thickness of 4 cm. It is designed to accommodate all types of coatings. ADVANTAGES: - quick drying respect to cement - suitable for all types of coating - it can be mixed with lightweight aggregates HOW TO APPLY IT: MIXTO PAVI must be mixed with clean floor screed sand, free from organic substances, with proper granulometry curve (from 0 to 4–5 mm), and water. The mix can be prepared manually or by concrete mixer. MIXTO PAVI can be mixed, whenever necessary, with lightweight aggregate (cork, expanded clay, polystyrene etc.) in order to package lightened floor screeds used for filling. DOSAGE FOR TRADITIONAL FLOOR SCREED: approx. 250 kg/m²

SPECIAL BINDING AGENTS FOR FLOOR SCREEDS

QUICK DRYING SPECIAL BINDING AGENTS FOR LOW THICKNESS FLOOR SCREED

MIXTO PAVI R NEW BUILDINGS

SPECIAL BINDING AGENTS FOR FLOOR SCREEDS

TECHNICAL CHARACTERISTICS: MIXTO PAVI R is a special hydraulic binder specific for yard preparation and for the installation of quick drying floor screeds. MIXTO PAVI R allows creating floor screed for civil use, ready to be walked on 12/24 hrs after installation and it can be finished on any type of surfaces. MIXTO PAVI R is compliant to UNI EN 413-1 and it is classifiable as MC22.5X. FIELD OF APPLICATION: MIXTO PAVI R is used in addition to aggregate for floor screed with a maximum granulometry of 4/5 mm to create quick drying substrates with a minimum thickness of 4 cm. MIXTO PAVI R reduces pavement placing waiting time respect to traditional preparation of standard floor screeds in sand and cement. ADVANTAGES: - quick, it reduces waiting time - suitable for construction of floor heating systems HOW TO APPLY IT: MIXTO PAVI R must be mixed only and exclusively with clean sand used for floor screed with an adequate granulometry curve (from 0 to 4–5 mm), and water depending on the recommended dosage. Mix can be performed manually or through a concrete mixer. DOSAGE: approx. 250 kg/m²

YIELD: approx. 2.5 kg/(m²x cm)

28 days COMPRESSION STRENGTH (UNI EN 196-1): approx. 28 N/mm² PACKAGE: 25 kg sack

COMPRESSION STRENGTH at 28 days (UNI EN 196-1): approx. 38 N/mm² PACKAGE: 25 kg sack

FLOORS SPECIAL BINDING AGENTS FOR FLOOR SCREEDS

SPECIAL BINDING AGENTS FOR LOW THICKNESS FLOOR SCREED

MIXTO PAVI B

TECHNICAL CHARACTERISTICS: MIXTO PAVI B is a special hydraulic cement binder for yard preparation and installation of low thickness and high elasticity floor screeds. MIXTO PAVI B is compliant to UNI EN 413-1 and it is classifiable as class MC22.5X in reference to this rule. FIELD OF APPLICATION: MIXTO PAVI B allows constructing floor screeds with a thickness greater than 1 cm and with excellent elasticity, adhesion and mechanical strength; it can be walked on 12–24 hrs after installation and it can be finished with tiles, natural stones, wood, or carpet. It is used in addition to aggregate for floor screeds with a maximum granulometry of 3–4 mm. MIXTO PAVI B reduces pavement installation time respect to traditional preparation of standard floor screeds in sand and cement. MIXTO PAVI B is suitable for renovations because it allows performing floor screeds on discontinuous and heterogeneous surfaces. ADVANTAGES: - excellent primer - controlled shrinkage - it reduces waiting time - suitable for renovation HOW TO APPLY IT: MIXTO PAVI B must be mixed only and exclusively with clean sand used for floor screed with an adequate granulometry curve (from 0 to 3–4 mm) and water, depending on the recommended dosage. Mixing can be performed manually or through a concrete mixer. DOSAGE: approx. 300 kg/m² YIELD: approx. 3 kg/(m²x cm) 28 days COMPRESSION STRENGTH (UNI EN 196-1): approx. 35 N/mm² PACKAGE: 25 kg sack

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

Residential building - Cluj, Romania

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

NEW BUILDINGS

FLOORS

PAVI/1

T H ERMALLY INSULATED LI G H TWE IG HT FLO O R SC RE E D

TECHNICAL CHARACTERISTICS: PAVI/1 is a lightweight, fiber-reinforced, polystyrene and hydraulic binder-based floor screed to be used as a thermally insulating base for filling between the floor and the floor screed pavement installation. PAVI/1 is compliant to Italian Ministerial Decree of 10/05/2004.

F LOOR S CREEDS

T48S/N

FIELD OF APPLICATION: PAVI/1 allows covering with ease the pipes of electric and hydraulic systems placed on the floor in order to obtain a flat surface on which to apply the floor screed installation. PAVI/1 provides high thermal insulation and it is sound-absorbent.

TECHNICAL CHARACTERISTICS: T48S/N is a hydraulic binder-based fiber-reinforced grout combined with selected aggregates, ideal to create quick drying floor screeds for civil use. T48S/N is compliant to UNI EN 13813" Screed material and floor screeds. Screed material. Properties and requirements" designed to be in compliance to EN 13813 CT-C25-F5 and subject to CE marking in accordance to current legislation. T48S/N is compliant to Italian Ministerial Decree 10/05/2004. FIELD OF APPLICATION: T48S/N is a fiber-reinforced grout to be used for installation of quick drying floor screeds for civil use with a thickness in the range of 4–6 cm. T48S/N is suitable for floor heating systems and it is compatible with the installation of electro welded reinforced meshes.

ADVANTAGES: - sound absorbent and thermally insulating - lightweight - certified mechanical strength

PAVI/1

T48S/N

QU ICK DRYING F LOOR S CREED

NEW BUILDINGS

FLOOR SC R E E DS

FLOORS

ADVANTAGES: - suitable for floor heating system - it allows creating quick drying mixes - certified mechanical strength

HOW TO APPLY IT: PAVI/1 must be applied directly above the floor and the pipes, with a thickness greater than 2–3 cm, making sure to meet the levelling requirements by using a rake, post or trowel.

HOW TO APPLY IT: T48S/N must be placed afar from perimeter walls and floor with thicknesses in the range of 4–6 cm. It must be applied and leveled using a post and trowel, according to standard methods of application of traditional grouts for civil use floor screeds. It is advisable to apply a polyethylene sheet (minimum thickness 0.2 mm) or similar vapor barrier between the floor whether thermally insulated or not, and the T48S/N.

MIXING WATER: 7-10 liters/sack YIELD: approx. 3÷4 kg/(m²x cm) PACKAGE: 12 kg sack

MIXING WATER: 2 liters/sack YIELD: approx. 20 kg/(m² x cm) TESTED

TESTED

certified mechanical strength

thermally insulating

sound absorbent

FLOORS FLOOR SC R E E DS

PACKAGE: 30 kg sack

FLOORS R E A DY FLO O R SC RE E D

MASSETTO

TECHNICAL CHARACTERISTICS: MASSETTO floor screed is a hydraulic binder-based grout and selected aggregates ideal to apply floor screeds for interior and exterior civil use. MASSETTO is compliant to UNI EN 13813 "Screed material and floor screeds. Screed material. Properties and requirements" designed to be in compliance to EN 13813 CT-C25-F5 and subject to CE marking in accordance to current legislation. PAVI/1 is compliant to Italian Ministerial Decree 10/05/2004. FIELD OF APPLICATION: MASSETTO is a grout to be used for installation of floor screeds for civil use with thicknesses ranging from 4 to 12 cm. MASSETTO is suitable for floor heating systems and it is compatible with the installation of electro welded reinforced meshes. ADVANTAGES: - it ensures quick installation - certified mechanical strength HOW TO APPLY IT: MASSETTO must be placed afar from the perimeter walls; it must be applied and leveled using a post and trowel according to standard methods of application of traditional sand and cement grouts for civil use floor screeds. MIXING WATER: 3 liters/sack

F LOOR S CREEDS

T48S/B

LOW TH ICKNESS F LOOR S CREED

TECHNICAL CHARACTERISTICS: T48S/B is a hydraulic binder based fiber-reinforced grout combined with selected aggregates ideal to create high adhesion floor screeds for civil use to be applied with a thickness in the range of 2 and 4 cm. T48S/B is compliant to UNI EN 13813" Screed material and floor screeds. Screed material. Properties and requirements" designed to be in compliance to EN 13813 CT-C25-F5 and subject to CE marking in accordance to current legislation. T48S/B is compliant to Italian Ministerial Decree 10/05/2004. FIELD OF APPLICATION: T48S/B is a grout to be used for installation of floor screeds for civil use with thickness in the range of 2–4 cm. T48S/B is applied directly to existing floors or floor screeds that require floor screed with a thickness lower or equal to 4 cm in order to match the height of the finished floor. ADVANTAGES: - high adhesion - certified mechanical strength HOW TO APPLY IT: T48S/B must be placed afar from the perimeter walls in layers with a thickness in the range of 2 and 4 cm, applied and leveled using a post and trowel according to standard methods of application of traditional sand and cement grouts for civil use floor screeds. MIXING WATER: 3 liters/sack

YIELD: approx. 20 kg/(m²x cm)

PACKAGE: 30 kg sack

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

IN CONFORMITY WITH UNI EN 13813

TESTED

IN CONFORMITY WITH UNI EN 13813

TESTED

ABILITY

CT-C25-F5

high mechanical resistance

CT-C25-F5-B0,5

high mechanical resistance

for irregular existing screeds

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

NEW BUILDINGS

FLOORS

T-FIX

P R OFESSIONAL ADHESIVE FO R INTE RIO RS

BONDING A DH ES IVES

TECHNICAL CHARACTERISTICS: T-FIX Flex is a flexible and elastic cement adhesive, free from vertical sliding and featuring extended open time, suitable for horizontal and vertical bonding of tiles and stone materials both for exteriors and interiors. Classification under UNI EN 12004 class C1TE – cement adhesive (C), standard setting (1) adhesive, reduced sliding (T) and extended open time adhesive (E).

FIELD OF APPLICATION: T-FIX is used as an adhesive for the installation of ceramic tiles (fired brick, single fired tiles, double fired tiles, clinkers, glazed porcelain, etc.) and stone material for wall or floor installation exclusively for interiors.

FIELD OF APPLICATION: T-FIX Flex, thanks to its flexible and elastic technology, is suitable for installation on floor screeds equipped with a radiant system or high format coating. It is used as an adhesive for installation of ceramic tiles (fired brick, single fired tiles, double fired tiles, clinkers, glazed porcelain, etc.) and stone material for walls or floors both for interiors and exteriors.

ADVANTAGES: - no vertical sliding - high adhesion

ADVANTAGES: - flexible technology - designed for the large area installations on radiant floors - no vertical sliding - high adhesion

HOW TO APPLY IT: T-FIX is applied to clean and dry surfaces. In order to improve adhesion it is suggested to spread a thin layer of glue on the surface, using a smooth metal spatula and immediately after spread the same glue using a toothed spatula. Under standard conditions (laboratory test) the adhesive open time is 20 minutes.

YIELD: approx.. 3-4 Kg/m2

HOW TO APPLY IT: T-FIX Flex is applied to clean and dry surfaces free from dust. In order to improve adhesion, it is advisable to spread a thin layer of glue on the surface by using a smooth metal spatula and immediately after spread the same glue by using a toothed spatula. Install the tile making sure that the surface is dried, clean and free from dust and exert proper pressure to ensure that the adhesive moists the tile completely.

PACKAGE: 25 kg sack

MIXING WATER: 6,5 liters sack

MIXING WATER: 6,5 l/sack

CERTIFICATE

EN 12004

no vertical sliding

FLOORS

CERTIFICATE

no vertical sliding

HTP: technology

PACKAGE: 25 kg sack ABILITY

ABILITY

EN 12004

flexible

high format

radiant floors

FLOORS

T-FIX IE

PROFESSIONAL ADHESIVE FOR INTERIORS AND EXTERIORS

TECHNICAL CHARACTERISTICS: T-FIX IE is a standard setting cement adhesive free from vertical sliding, suitable for horizontal and vertical interior bonding of ceramic tiles, stoneware, clinkers, and stone materials. It is classified under UNI EN 12004 Class C1TE – cement adhesive (C), standard setting adhesive (1), reduced sliding (T) and extended open time (E) adhesive. FIELD OF APPLICATION: T-FIX IE is used as an adhesive for the installation of ceramic tiles and stone material on walls or floors, both for interiors and exteriors. ADVANTAGES: - no vertical sliding - extended open time - high adhesion HOW TO APPLY IT: T-FIX IE must be applied to dry and clean surfaces free from dust to improve adhesion. It is advisable to spread a thin layer of glue on the surface by using a smooth metal spatula and immediately after spread the same glue using a toothed spatula. Under standard conditions (laboratory test) the adhesive open time is 30 minutes.

BONDING A DH ES IVES

T-FIX HP

HIGH PERFORMANCE PROF ESS IONA L A DH ES IVE

TECHNICAL CHARACTERISTICS: T-FIX hp is a high performance cement adhesive free from vertical sliding and featuring extended open time suitable for horizontal and vertical bonding of ceramic tiles, stoneware, clinkers, and stone materials both for exteriors and interiors. It is classified under UNI EN 12004 class C2TE – cement adhesive (C), enhanced and added characteristics adhesive (2), reduced sliding (T) and extended open time adhesive (E). FIELD OF APPLICATION: T-FIX hp is used as an installation adhesive under particularly challenging conditions on surfaces and ceramic tiles (fired brick, single fired tiles, double fired tiles, clinkers, glazed porcelain, etc.) and on stone material for walls or floors, both for interiors and exteriors. ADVANTAGES: - flexible technology - designed for large area installations on radiant floors - no vertical sliding - high adhesion

YIELD: approx. 3-4 Kg/m²

HOW TO APPLY IT: T-FIX hp is applied to clean and dry surfaces free from dust. In order to improve adhesion it is advisable to spread a thin layer of glue on the surface using a smooth metal spatula and immediately after spread the same glue using a toothed spatula. Install the tile making sure that the surface is dry, clean and free from dust and exert proper pressure to ensure that the adhesive moistens the tile completely.

PACKAGE: 25 kg sack

MIXING WATER: 7 liters/sack

MIXING WATER: 6.5 liters/sack

CERTIFICATE

C1TE EN 12004

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

YIELD: approx. 3-4 Kg/m²

C1TE

C1T

B OND IN G ADH E S I VE S

T-FIX FLEX

FLEXIBLE AND PROFESSIONAL A DH ES IVE

NEW BUILDINGS

B O N D IN G ADH E S I V E S

FLOORS

CERTIFICATE

60’

C2TE

15 30

no vertical sliding

YIELD: approx. 3-4 Kg/m²

open time

EN 12004

CERTIFICATE

no vertical sliding

PACKAGE: 25 kg sack CERTIFICATE

ABILITY

high

for every material

HTP: adhesion

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

NEW BUILDINGS

FLOORS

T-LIVEL

S E L F-LE V E LING TO P C OAT P LASTE R

NEW BUILDINGS

SE L F-L E V E L I N G FIN ISHIN G COAT

TECHNICAL CHARACTERISTICS: T-LIVEL is a high fluidity self-leveling finishing coat less than 2 mm thick, ideal for smoothing and finishing on traditional quick drying floor screeds. FIELD OF APPLICATION: T-LIVEL can be applied to traditional or quick drying interior floor screeds. It improves surface finishing avoiding roughness due to traditional floor screeds finishing defects. ADVANTAGES: - high resistance to abrasion - high adhesion - certified mechanical strength HOW TO APPLY IT: a thin layer of T-LIVEL must be spread on the existing floor screeds using a metal spatula. MIXING WATER: 7 liters/sack YIELD: approx. 2.5 Kg/m² PACKAGE: 30 kg sack

ABILITY

CERTIFICATE

high fluidity

high adhesion

THERMAL INSULATION T HE R MAL PLA S TE R S

T H ERMAL INSULATED P LA STE R

TERMO-TASS

TECHNICAL CHARACTERISTICS: TERMO-TASS is a hydraulic binder-based thermal insulated fiberreinforced plaster combined with aggregates and selected lightweight minerals and polystyrene. It combines low thermal conductivity with ease of application and compatibility to a variety of masonry surfaces as well as high consistency and durability. TERMO-TASS is breathable and heat resistant, maintaining high average temperature within the wall and on the interior wall surface, improving energy savings and environmental comfort. TERMO-TASS is compliant to UNI EN 998-1 "Specifications for mortar for masonry – interior and exterior plaster mortars" and it is subject to CE marking in accordance to the regulations in force. FIELD OF APPLICATION: TERMO-TASS must be used to create machine processed breathable thermal insulated plasters for exteriors with a thickness greater than 2 cm on brick, stone, solid brick, concrete masonries, etc. ADVANTAGES: - highly insulating - suitable for any types of surfaces - breathable and resistant HOW TO APPLY IT: TERMO-TASS must be applied, also on uneven and discontinuous masonries, using a plastering machine for ready-to-use plaster and applied directly on the wall using a post screed. It is advisable to limit processing of material on the wall in order to avoid process off-cuts or excessive mix compacting. Thicknesses greater than 4 cm have to be achieved by applying several coats. MIXING WATER: approx. 0.85 liters/Kg (approx. 10 liters/sack) YIELD: approx. 3 Kg/(m2 x cm) THERMAL CONDUCTIVITY (EN 12667): class T1 λ = 0,067 W/(m x °K) PACKAGE: 12 kg sack

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

NEW BUILDINGS

THERMAL INSULATION

THERMAL INSULATION CL A DDING BONDING AGENT

PL ATE TH ERMA L CL A DDING BONDING AGENT

TECHNICAL CHARACTERISTICS: TAØ2 is a top coat plaster – primer in FENIX NHL5 certified natural hydraulic lime, selected dolomitic aggregates and natural cellulose, suitable for leveling any surface that is particularly challenging in terms of adhesion.

TECHNICAL CHARACTERISTICS: TKØ1/gr, bn is a grey (TKØ1/gr) or white (TKØ1/bn) cement in hydraulic binder agents and selected aggregates characterized by high elasticity and adhesive strength. It is compliant to ETAG 004 guidelines.

FIELD OF APPLICATION: TAØ2 is used as a top coat plaster – primer on all types of surfaces and where it is necessary to level a rough plaster surface. TAØ2 can be applied to any surface where a careful preparation of the base for subsequent finishing or plastering is required.

FIELD OF APPLICATION: TKØ1/gr, bn is used to install all the thermal insulation panels (polystyrene, rock wool, cork, etc.) and subsequently in leveling the exterior surface, in anticipation of its finishing.

ADVANTAGES: - high adhesion capacity - all natural - compatible with the existing masonries - typical hazelnut color

ADVANTAGES: - high elasticity - greater adhesive strength HOW TO APPLY IT: when used as a bonding agent: TKØ1/gr,bn must be applied between panel and support in such quantities to ensure good adhesion and stability to the system (4-5 kg/m²). When used as leveling: apply it to the exterior surface of the panel by spreading a first layer of bonding agent using a toothed metal spatula, then apply a fiberglass mesh and proceed to further leveling using a metal trowel.

HOW TO APPLY IT: TAØ2 must be spread by metal trowel and finished with a metal plastering trowel (sanding), plastic or sponge trowel, or with other tools depending on the type and degree of desired finishing. It can be subsequently painted or left exposed. It is compatible with the subsequent application of setting coat, putty, marmorinos, stuccos, plastic or mineral coatings, tiles, wallpaper, etc. It can include fiberglass meshes in the creation of reinforced shavings on existing cracked plasters. Used as a bonding plaster, it must be left rough in anticipation of plastering. MIXING WATER: 0.23 liters/Kg (approx. 7 liters/sack)

YIELD: 3÷5 Kg/m²

WATER ABSORPTION: class W2 (UNI EN 1015-18)

MIXING WATER: 0.25 liters/Kg (approx. 6.5 liters/sack)

LEVELING YIELD: 3÷4 Kg/m2

PANEL ADHESION (ETAG 004): > 0,08 N/mm2

BONDING YIELD: 4÷5 Kg/m2

PACKAGE: 25 kg sack

PACKAGE: 30 kg sack TKØ1 BONDING IS COMPLIANT TO

natural hydraulic lime

high edhesion

usable as plaster

high adhesion on cls

without cement and additives

high spreadability

ETAG 004

C O LORED MINERAL F I N ISHING

ETAG 004

Tassullo Finishing

CL A DDING BONDING AGENTS

high adherence

HIGH YIELD AND HIGH WORKABILITY THERMAL CL A DDING BONDING AGENT

ISI-FISS

TECHNICAL CHARACTERISTICS: TASSULLO mineral FINISHING products are available in white and in various colors for interiors and exteriors; they are in natural materials such as hydraulic lime, hydrated lime and selected aggregates that are dry-premixed and combined with colored elements and natural pigments. Three different granulometries are available: fine, medium and coarse.

TECHNICAL CHARACTERISTICS: ISI-FISS (gr, bn) is a special bonding agent and top coat plaster in white or grey color featuring high performance, adhesion and elasticity. The high adhesion performance makes the product suitable for installation on all types of panels. ISI- FISS (gr, bn) is compliant to ETAG 004 European guidelines.

FIELD OF APPLICATION: it is used for white or colored mineral finishing on new or existing plasters, concrete, drywalls, and plate thermal insulated panels

FIELD OF APPLICATION: ISI-FISS is specifically designed for bonding and subsequent leveling all types insulated panels (polystyrene, rock wool, cork, etc...).

ADVANTAGES: - natural - high aesthetic yield - durable

ADVANTAGES: - suitable for bonding on all types of surfaces - high adhesive strength - high yield

HOW TO APPLY IT: the best chromatic and aesthetic results obtainable using TASSULLO FINISHING are achieved by applying the product in a single and thin coat on even and regular surfaces. It is advisable to proceed as follows: prepare the base plaster for all surfaces to be plastered paying attention to troweling the surface evenly so as to create a smooth and uniform absorbent surface; on rough surfaces that have been already plastered apply TASSULLO TAØ1 or TAØ2 top coat plaster with a spatula in order to allow the application of one coat of thin TASSULLO mineral finishing. TASSULLO mineral finishing can be finished using a plastic or sponge trowel, cloth or other tool depending on the finishing degree and desired aesthetic effect.

HOW TO APPLY IT: when used as a bonding agent: ISI- FISS (gr, bn) must be applied between panel and surface in such quantities to ensure good adhesion and stability to the system (3-5 kg/m²). When used as leveling: apply it on the exterior surface of the panel by spreading a first layer of bonding agent using a toothed metal spatula then apply a fiberglass mesh and proceed to further leveling using a metal trowel. MIXING WATER: 0.24 liters/Kg (6 liters/sack) BONDING YIELD: 3,5 Kg/m2 LEVELING YIELD: 2÷3 Kg/m2

MIXING WATER: 0.2–0.25 liters/Kg (6–7.5 liters/sack) YIELD (e.g. with medium finishing): 3,5 Kg/m2 GRANULOMETRY: fine 0 – 0,8 mm / medium 0 – 2 mm / coarse 0 – 4 mm PACKAGE: 30 kg sack

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

IN CONFORMITY WITH

THERMAL INSULATION

THERMAL INSULATION FIN ISHIN G

TKØ1/gr,bn NEW BUILDINGS

TAØ2

M E D IUM P RIM E R TO P C OAT P LASTE R

TOP C OAT P LA S TE R S

ISI-FISS BONDING IS COMPLIANT TO

PANEL ADHESION (ETAG 004): > 0,08 N/mm2 PACKAGE: 25 kg sack

ETAG 004

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

NEW BUILDINGS

THERMAL INSULATION

ISI-THERM NEW BUILDINGS

E X PANDED P O LYSTYRENE THERMAL I N SULATIO N SYSTE M

P O LY S T Y R E N E P L AT E C L A D D I N G

TECHNICAL CHARACTERISTICS: ISI-THERM is a complete expanded polystyrene plate thermal insulation system with an ISI-FISS bonding agent and top coat plaster white or grey in color, featuring high adhesion and elasticity. It is an easy and cost effective product to improve home comfort. FIELD OF APPLICATION: cladding system is recommended for a variety of surfaces, especially for concrete, brick and for old plastered surfaces. ADVANTAGES : - tested in reference to ETA-09/135 - immediate energy and cost savings - easy to install - high insulation THE SYSTEM COMES COMPLETE WITH ALL THE REQUIRED ACCESSORIES: bonding agent/top coat plaster ISI-FISS GR/Bn, insulated plates, AR160 fiberglass meshes, locking nails, colored finishing and accessories (corners bead, initial profiles, etc.). PLEASE SEE DATA SHEET FOR THE FULL VIEW OF THE TECHNICAL DATA, FIELDS OF USE, METHODS AND APPLICATION NOTES.

ISI-FISS BONDING IS COMPLIANT TO

ETAG 004

B-Haus - Pordenone - Italy

Residential building - Vicenza - Italy

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

1 - BINDING AGENTS

5 - FINISHING AND LEVELING

_Fenix NHL5

_TAØØ/TAØ1/TAØ2/TAØ4

_Fenix NHL 3,5 Chiara

_TBØØ/TBØ1/TBØ2/TBØ4

_Grassello

_TF01/TF02/TF04 _TFS1

2 - CONSOLIDATION

HYSTORICAL BUILDINGS

6 - DEHUMIDIFICATION AND WATERPROOFING _Fenix-B consolidamento _T30rc

_TLast-100 _T30S

_TBL _T-FLASH Restauro

3 - MORTARS

7 - STONE ELEMENTS RECONSTRUCTION _T-Stone

_T20V _T20V Color _T30rc

8 - THERMAL INSULATION

4 - PLASTERS

_TERMO-BI

_T25V _T30V _T30V/Fibro _T30S

Arena of Verona - Italy

This building was the subject of a research study between Tassullo and the City of Verona

Renovation and recovery of historical buildings, historical sites, buildings protected and regulated by Environmental and Architectural Heritage Agencies 62

Fenix Calcerestauro is a line of certified products in natural hydraulic lime, FENIX certified: certified and durable materials that, above all, are compatible from a physical, chemical and chromatic stand point with all types of historical masonries.

www.calcerestauro.it

PRODUCT DATA SHEET > 63

CONSOLIDATION OF MASONRY PILLARS

SEALING OF JOINTS IN EXPOSED SURFACE MASONRIES

CONSOLIDATION OF MASONRIES THROUGH INJECTIONS

REINFORCED RENDERING SYSTEM AND FINISHING

FENIX/B TF01 T20V

TAØ2

FENIX/B

T30V T30rc

VAULT CONSOLIDATION

MASONRY CONSOLIDATION THROUGH MORTARS AND PLASTER REPAIRING

TBL T30rc T30V

FENIX/B

CONSOLIDATION OF MASONRIES THAT ARE NOT SCARFED THROUGH TIES BEAMS AND CHAINS

“LIKE FOR LIKE” REPLACEMENT CONSOLIDATION SYSTEM

FENIX/B T30rc

HISTORICAL BUILDINGS Systems and applications 64

LEED

HYSTORICAL BUILDINGS

T30rc

HISTORICAL BUILDINGS

BINDING AGENTS

FENIX NHL5

NATU RA L NH L 3 .5 CERTIF IED L IGH T H YDRA U L IC L IME

TECHNICAL CHARACTERISTICS: FENIX NHL5 is a high quality and high purity product obtained by firing and quenching exclusively marl-limestone extracted using modern technologies from natural banks, accurately following the teachings of our heritage. NHL FENIX 5 features a warm and unmistakable hazelnut color, which is the distinguishing feature of natural hydraulic lime. The low salt content and the very low content of free lime ensure compliance to the chemical and physical characteristics of original masonry due to the absence of reactivity, which does not trigger degradation mechanisms. FENIX NHL 5 is the basis for the best mortars for renovations and for all the products that are part of the Tassullo Fenix Calcerestauro line.

FENIX NHL 3,5 Chiara

TECHNICAL CHARACTERISTICS: FENIX NHL 3,5 Light is a natural hydraulic lime NHL3.5 certified according to UNI EN 459-1. It is made in Italy, as proven by the FCP production certificate and CE mark. FENIX NHL 3.5 Light is characterized by a light beige color that allows working on historical masonries by reducing the color impact between new and existing ones. FENIX NHL 3.5 Light is obtained by firing and quenching exclusively marl-limestone extracted using modern technologies from natural banks accurately following the teachings of our heritage. FIELD OF APPLICATION: FENIX NHL 3,5 Light is a certified natural hydraulic lime for the restoration of important buildings and the renovation of historical and heritage buildings protected and regulated by Environmental and Architectural Heritage Agencies. FENIX NHL 3.5 Light is suitable for the preparation of bedding mortars for brick masonry, stone, solid brick, and for creating floor screeds, base and finishing plasters with high breathability and workability characterized by the absence of reactivity to sulfates.

FIELD OF APPLICATION: FENIX NHL5 is a certified natural hydraulic lime for the restoration of important buildings and for the renovation of historical and heritage buildings protected and regulated by Environmental and Architectural Heritage Agencies. FENIX NHL 5 is ideal for mixing with local aggregates that are suitable for the specific work to be carried out; thus, recreating traditional and local aesthetic and chromatic effects.

HYSTORICAL BUILDINGS

N HL 5 C E R T IF I E D N ATU R A L H Y DR A U LI C LIM E

ADVANTAGES: - clear color - compatible with existing masonries - NHL 3.5 certified according to UNI EN 459-1 - very low content of water-soluble salts - certified origin and production

ADVANTAGES: - compatible with existing masonries - NHL 5 certified according to UNI EN 459-1 - very low content of water-soluble salts - sulfate resistant - typical hazelnut color - certified origin and production

HOW TO APPLY IT: FENIX NHL 3,5 Light allows creating mortars and plasters that during the curing stage have the lowest content of water-soluble salts, which are the cause of salt efflorescence. APPARENT DENSITY: approx. 1100 kg/m3

HOW TO APPLY IT: FENIX NHL5 allows creating mortars and plasters that during the curing stage have the lowest content of water-soluble salts, which are the cause of salt efflorescence. NHL FENIX 5 must be mixed with clean and selected aggregates, free from organic substances, at the rate of 350÷450 Kg/m3 and clean water depending on the desired consistency of the mix. The use of aggregates with an excess or defect of fine parts will involve the preparation of non-workable mixes ("lean" or "fat") that are affected by non adequate resistance and durability. The mix can be prepared manually or using a concrete mixer.

MECHANICAL STRENGTH AFTER 28 DAYS: > 3,5 N/mm2 PACKAGE: 25 Kg sack or loose

APPARENT DENSITY: approx. 1100 kg/m3

BINDING AGENTS

MECHANICAL STRENGTH AFTER 28 DAYS: > 5 N/mm2 PACKAGE: 25 Kg sack or loose

GRASSELLO

A IR BINDER PA S TE

TECHNICAL CHARACTERISTICS: GRASSELLO is an air lime paste obtained from processing quicklime in a tank for over a month. TASSULLO GRASSELLO is compliant to UNI EN 459-1 "Building lime. Definitions, specifications and conformity criteria" classified as CL-80 S and subject to CE marking according to regulations in force.

REF ERE NCES

FIELD OF APPLICATION: TASSULLO GRASSELLO can be used in addition to TASSULLO natural hydraulic lime or more in general to hydraulic lime or cement in the preparation of finishing or cement-lime mortar at the building yard. The addition of TASSULLO GRASSELLO to hydraulic mortar increases workability and plasticity. ADVANTAGES: certified YIELD: approx.2 Kg/m² PACKAGE: 25 Kg sack

Arena of Verona (VR) - Italy pilot project building yard

Council Palace of Cles (TN) - Italy

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

Votive Chapel of Santa Maria Mater Domini, Vicenza - Italy

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

HISTORICAL BUILDINGS

HISTORICAL BUILDINGS CONSOLIDATION

C O N SO L IDATI O N I N J E CTI O N M I X TU R E

FENIX-B

TBL

F IBER- REINFORCED L IGH TW EIGH T GROU T

TECHNICAL CHARACTERISTICS: FENIX-B is a special high fluidity mix exclusively based on FENIX 5 NHL natural hydraulic lime, with low water-soluble salts, sulfate resistant, suitable for the consolidation of masonry structures in stone, mixed stone or solid brick filled by injection, tested and developed in cooperation with the University of Padua and ENEA. FENIX-B allows recreating from a physical, chemical and mineralogical point of view, the original binder-based bedding mortars obtained by firing clayey limestone at low temperatures.

TECHNICAL CHARACTERISTICS: TBL is a lightweight fiber-reinforced grout in hydraulic lime FENIX NHL 5 certified and combined with selected lightweight mineral aggregates suitable for the application of structural reinforcements on stone vaults or wood floors by connecting reinforcement meshes. The mineralogical characteristics and the low presence of water-soluble salts make the product particularly suitable for the restoration and static improvement of structures that have the absolute need to limit overloading after consolidation.

FIELD OF APPLICATION: FENIX-B is suitable for the implementation of masonry consolidation by injection in all those cases in which restoring structural consistency to the masonry section affected by cracks, voids, lack of bedding mortar, etc. is desired. FENIX-B guarantees restoration of masonry mechanical strength and structural uniformity by filling up all the empty gaps.

FIELD OF APPLICATION: TBL is used for the renovation of historical buildings and heritage buildings protected and regulated by Environmental and Architectural Heritage Agencies, specifically in the creation of reinforced grouts for structural consolidation where overloading concerns are as significant as mechanical ones. It allows creating floor screeds or consolidating coping stones with a minimum thickness of 4 cm to be created on the extrados of vaults or stone, masonry, or wood slabs.

ADVANTAGES: - compatible with historical masonries - high fluidity - very low content of water-soluble salts - developed in cooperation with the University of Padua and ENEA in Rome

HYSTORICAL BUILDINGS

CONSOLIDATION

ADVANTAGES: - absence of chemical reactivity - high adhesion - compatible with the use of electro welded meshes - it contains FENIX NHL 5

HOW TO APPLY IT: FENIX-B once mixed with water can be injected into the masonry by its own weight through automatic pumping or automated machinery equipped with devices that control both flow and pressure. The injection process must include approx. 2 holes per square meter of masonry.

HOW TO APPLY IT the mixture can be applied manually or by plastering machine without nozzle and then applied using a rake, post, trowel etc.

APPARENT DENSITY: approx. 1.2 kg/dm3

MIXING WATER: approx. 0.5 liters/Kg (approx.10 liters/sack)

YIELD (mixture to be injected obtainable per kg of powder): approx. 0.65 l/Kg

COMPRESSION STRENGTH (UNI EN 1015-11): from 6 to 10 N /mm² (in the two available mechanical strength versions)

PACKAGE: 25 Kg sack

CONSOLIDATION

CONSOLIDATION C O N SO L IDATI N G R E N DE R I N G G R O U T

T30rc

TECHNICAL CHARACTERISTICS: T30rc is a grout in natural hydraulic lime FENIX NHL 5 certified containing selected aggregates for the creation of specific consolidating rendering, filling and padding, “like-for-like” replacements, construction of joints in exposed surface masonry and brick bedding mortars, locking of metal reinforcements characterized by high resistance, breathability and elasticity.T30rc is compliant to UNI EN 998-1 "Specifications for mortar for masonry – interior and exterior plaster mortars" and subject to CE marking in accordance to the regulations in force. FIELD OF APPLICATION: T30rc is a grout that must be used as consolidating rendering, and, if necessary, it can be reinforced and applied to stone masonries weakened by the loss of bedding mortar and where there is need to restore mortar joints or floor screeds subject to poor cohesion. T30RC can be used as mortar for “like-for-like” replacements in compliance to UNI EN 998-2 (class M5). ADVANTAGES: - creation of resistant but non inelastic mortars - it ensures quick application - compatible with electro welded meshes - it includes FENIX NHL 5 - certified mechanical strength

QU ICK MORTA R FOR RENOVATIONS A ND S A F ETY MEA S U RES

T-FLASH Restauro

TECHNICAL CHARACTERISTICS: T-FLASH Restauro is a thixotropic mortar with high plasticity and quick drying (approx. 40 minutes), suitable for use on historical masonries, specifically designed for filling or restoration of mortar joints. Its quick setting allows T-FLASH Restauro to quickly implement safety measures. FIELD OF APPLICATION: T-FLASH Restauro has been specifically designed for the implementation of safety measures in historical buildings affected by the Abruzzo earthquake occurred in April 2009. Ideal for the reconstruction, filling and sealing of mortar joints of degraded historical masonries. Its quick setting, hardening, and workability allow performing a quick implementation of the safety measures and a first reinforcement of the masonries that are awaiting renovation and final structural reinforcement. It allows filling joints between stone or brick masonry without causing any shrinking or detachment from the masonry. ADVANTAGES: - compatible with historical masonries - quick drying - specifically designed for the implementation of safety measures of historical buildings - applicable by machine

HOW TO APPLY IT: T30rc can be applied manually or by using a plastering machine suitable for traditional mortar with granulometry up to 4 mm as per standards.

HOW TO APPLY IT: T-FLASH Restauro can be applied manually or through a plastering machine. The mixture can be prepared manually, or using a low rpm drill, or a suitable plastering machine

MIXING WATER: approx. 0.15 liters/Kg (approx.4.5 liters/sack)

MIXING WATER: approx. 7 liters/30 kg sack

YIELD: 18 ÷ 19 Kg/(m2 x cm)

YIELD: approx.15 -16 Kg/(m²x cm)

COMPRESSION STRENGTH (UNI EN 1015-11): class CS IV ( > 6,0 N/mm2)

PACKAGE: 30 Kg sack

PACKAGE: 30 kg/sack or loose in silos

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

HISTORICAL BUILDINGS

SEALING MORTAR

PLASTERS

TECHNICAL CHARACTERISTICS: T20V is a sealing and bedding mortar in natural hydraulic lime FENIX NHL 5 certified and combined with selected aggregates, characterized by a very low content of watersoluble salts. T20V is used as mortar to seal stone masonry and it is also used as bedding mortar when it is desirable to obtain a particular finishing degree of the joining mortar in the installation and refinement of exposed bricks. T20V is compliant to UNI EN 998-2 "Specification for masonry mortar" and it is subject to CE marking in accordance to the regulations in force. FIELD OF APPLICATION: T20V is a mortar particularly suitable for the positioning of exposed surface bricks and/or for the restoration of joints between masonry parts (stones, bricks, etc.) and it is particularly suited for renovations where the formation of efflorescence causes significant functional and aesthetical damage. ADVANTAGES: - very low content of water-soluble salts - compatible with existing masonries - tested at the pilot project yard in the Verona Arena HOW TO APPLY IT: T20V is applied manually over any solid brick or stone masonries after having removed possible dust and uneven elements or other substances that can come between the support and the mortar layer. After having been applied, the exposed surface mortar is suitable for finishing using flat or hollow tools in order to obtain a compact grouting profile.

T25V

MACH INE A PPL IED PL A S TER

TECHNICAL CHARACTERISTICS: T25V is a plastering mortar in FENIX NHL 5 certified natural hydraulic lime and selected dolomitic aggregates, applicable by machine. T25V is a high elasticity mortar with low shrinkage particularly recommended for renovation. T25V mortar is designed to reduce shrinkage, to optimize workability and the possibility of using standard plastering machines for ready-to-use plaster at the time of its application. T25V meets the technical specifications set by EN 998-1 "Specifications for mortar for masonry – interior and exterior plaster mortars" and it is subject to CE marking in accordance to the regulations in force. FIELD OF APPLICATION: T25V is applied to any interior or exterior surface and it is especially recommended for those renovations requiring high mechanical properties, absence of reactivity at the presence of salts, high adhesion to the wall and controlled shrinkage.

HYSTORICAL BUILDINGS

T20V

SE AL IN G AN D E X P O S E D S U R FACE M A S O NRY M O RTAR

ADVANTAGES: - controlled shrinkage and high adhesion - very low content of water-soluble salts - high thicknesses - compatible with existing masonries HOW TO APPLY IT: preparation of preliminary rendering using T25V in order to even out the water absorption of the surface in anticipation of the plastering body application; then subsequent application of T25V machine-mixed with water in one or more coats, depending on the thickness desired.

MIXING WATER: 0,18 liters/Kg (approx.5.5 liters/sack)

MIXING WATER: 0,21 liters/Kg (approx.6 liters/sack)

YIELD (Consumption for bedding brick sized 24 x 11 x 6 cm): approx. 30 Kg/m²

YIELD: approx.15 Kg/(m²x cm)

PACKAGE: 30 kg sack or loose in silos

PACKAGE: 30 Kg sack

SEALING MORTAR C OLOR E D SE A LI N G M O R TA R

T20V Color

TECHNICAL CHARACTERISTICS: T20V Color is a bedding mortar in natural hydraulic lime and selected aggregates that is suited as bedding mortar in order to achieve a specific hue and finishing level of the joining mortars, in installations and finishing of exposed bricks or mixed masonries. T20V Color is suitable for changing hue respect to the basic T20V hue in order to meet the aesthetic requirements of a variety of surfaces where it is applied. T20V Color is compliant to UNI EN 998-2 "Specification for masonry mortar," and it is subject to CE marking in accordance to the regulations in force. FIELD OF APPLICATION: T20V Color is a mortar applicable to any surface and suitable for the construction of the junction layer between stones, bricks, etc. as well as for special finishing, both from a physical and chromatic stand point. ADVANTAGES: - specifically designed to satisfy the aesthetic needs of the client - compatible with existing historical masonries - already available in a variety of hues HOW TO APPLY IT: T20V Color is applied manually according to standard application methods for bedding mortars on exposed surface masonries. After applying it, the exposed surface mortar is suitable for finishing using flat or hollow tools in order to obtain a compact grouting profile. Avoid repeated moistening of the mortar in order to extend its workability and finishing capabilities. MIXING WATER: 0,21 liters/Kg (approx.6.5 liters/sack) YIELD (Consumption for bedding brick sized 24 x 11 x 6 cm): approx.13.5 Kg/(m²x cm) COMPRESSION STRENGTH (UNI EN 1015-11): CS II ( 1,5 ÷ 5 N/mm2) PACKAGE: 30 kg sack or loose in silos Church of San Nicolò – Tuenno (TN) - Italy

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

HISTORICAL BUILDINGS

HISTORICAL BUILDINGS PLASTERS

T30V

P L AST E R ING M O R TA R

T30S

WATERPROOF PL A S TERING MORTA R

TECHNICAL CHARACTERISTICS: T30V is a plastering mortar for rendering and creation of joints in exposed surface masonries, in natural hydraulic lime FENIX NHL 5 certified and selected aggregates with a maximum granulometry of 4 mm. T30V is a mortar with medium-high resistance and low watersoluble salts suitable for the renovation of historical buildings and heritage buildings, protected and regulated by Environmental and Architectural Heritage Agencies.

TECHNICAL CHARACTERISTICS: T30S is a breathable waterproof mortar in FENIX NHL 5 certified natural hydraulic lime and selected aggregates. T30S is suitable for the recovery of masonry damaged by rising humidity since it combines the breathability of natural hydraulic lime and an active waterproofing action. T30S is compliant to UNI EN 998-1 “Specifications for mortar for masonry – interior and exterior plaster mortars” and subject to CE marking in compliance to the regulations in force.

FIELD OF APPLICATION: T30V is applied to any interior or exterior surface and it is especially recommended for those renovations requiring high mechanical properties, absence of reactivity in presence of salts, high adhesion to the wall and controlled shrinkage.

FIELD OF APPLICATION: T30S allows recovering masonry damaged by rising humidity through capillarity, or, in any case, it allows the recovery of all the masonry structures in which plaster durability is seriously compromised by humidity. T30S can be applied to any masonry wall where high breathability, extremely low water absorption by capillarity and high chemical/physical mortar inertia are required. T30S is particularly suited for exterior wainscots.

ADVANTAGES: - high workability - controlled shrinkage - very low content of water-soluble salts - compatible with existing masonries HOW TO APPLY IT: prepare a preliminary rendering on dry masonry using T30V or T30RC and a slight excess of water in order to regulate the surface; apply the plaster using T30V mixed with water in one or more coats, depending on the thickness desired. MIXING WATER: 0,16 liters/Kg (approx.5 liters/sack)

HYSTORICAL BUILDINGS

PLASTERS

ADVANTAGES: - waterproof - breathable - extremely low content of water soluble salts HOW TO APPLY IT: prepare a preliminary rendering using T30V in order to regularize the surface and then apply the plaster body; the plaster body application takes place using T30S mixed with water in a 2÷3 cm thick single coat.

YIELD (for plaster): approx.18 Kg/(m²x cm)

WATER CAPILLARY ABSORPTION(UNI EN 1015-18: class W2: c < 0,05 Kg/(m2 x min 0,5)

PACKAGE: 30 kg sack or loose in silos

YIELD (for plaster): approx. 18 Kg/(m2 x cm) MIXING WATER: 0,16 l/Kg (approx. 5 l/sack) PACKAGE: 30 kg sack or loose in silos

FINISHING AND LEVELING

PLASTERS R E INFOR C E D M O R TA R FO R P LA S TE R

T30V/FIBRO

TECHNICAL CHARACTERISTICS: T30V/FIBRO is a fiber-reinforced mortar in hydraulic lime FENIX NHL 5 certified combined with selected aggregates; it is used as plaster in the rendering and construction of joints in exposed surface masonries. T30V FIBRO is compliant to UNI EN 998-1 "Specifications for mortar for masonry – interior and exterior plaster mortars" and it is subject to CE marking in accordance to the regulations in force. FIELD OF APPLICATION: T30V/FIBRO is applied to any interior or exterior surface and it is especially recommended for those renovations requiring high mechanical properties, absence of reactivity to salts, high adhesion to the wall and controlled shrinkage. It is particularly suitable in case of significant unevenness on the existing masonry. ADVANTAGES: - high thicknesses - ideal for masonries with significant unevenness - very low content of water-soluble salts HOW TO APPLY IT: prepare a preliminary rendering on dry masonry using T30V/FIBRO; apply the plaster using T30V/FIBRO mixed with water in one or more coats, depending on the thickness desired. MIXING WATER: 0,16 liters/Kg (approx.5 liters/sack) YIELD (for plaster): approx.18 Kg/(m²x cm) PACKAGE: 30 kg sack or loose in silos

EXTRA FINE, FINE, MEDIUM, COA RS E TOP COAT PL A S TER/ PRIMER

TAØØ/TAØ1 TAØ2/TAØ4

TECHNICAL CHARACTERISTICS: TA is a top coat plaster in FENIX NHL 5 certified natural hydraulic lime, dolomitic aggregates and natural cellulose, available in four different granulometries (from 0 to 4 mm: TAØØ, TAØ1, TAØ2, TAØ4), suitable for the leveling of all the surfaces that are challenging from an adhesion stand point. FIELD OF APPLICATION: TA is used as a top coat plaster – primer on each type of surface where it is necessary to level a surface constituted by separate plasters, for a subsequent finishing treatment. TA is compatible with the application of marmorinos, stuccos, plastic or mineral coatings. ADVANTAGES: - high adhesion - all natural - compatible with existing masonry - typical hazelnut color HOW TO APPLY IT: TA is applied using a metal trowel and it is finished with a plastic or sponge plastering trowel or other tools depending on the type and level of finishing desired. Then, it can be painted or left exposed. It is compatible with the subsequent application of setting coats, lime putty, marmorinos, stuccos, plastic or mineral coatings, wall paper etc. It can include fiberglass meshes in the preparation of reinforced armors on existing plasters with hair cracks. TAØ2 and TAØ4 are ideal as bonding bridges on all types of masonry in anticipation of plaster application. MIXING WATER: 0,23 l/Kg (approx.7 l/sack) YIELD: 3÷5 Kg/m2 PACKAGE: 30 kg sack

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

HISTORICAL BUILDINGS

FINISHING AND LEVELING

TBØØ/TBØ1 TBØ2/TBØ4

TECHNICAL CHARACTERISTICS: TB is a white top coat plaster available in four different granulometries (from 0 to 4 mm: TB ØØ, TB Ø1, TB Ø2, TB Ø4), suitable for leveling of all surfaces that are particularly demanding from an adhesion stand point. FIELD OF APPLICATION: TB is used as a top coat plaster on all types of surfaces and whenever it is necessary to level a surface constituted by rough plasters of different nature and aging. TB can be applied to any surface where a better preparation of the base is required for subsequent finishing treatment. TB is compatible with the subsequent application of marmorinos, stuccos, and plastic or mineral coatings. ADVANTAGES: - high adhesion - solvents free - it does not form any vapor barrier - it can be left as an exposed surface

HOW TO APPLY IT: TFS1 can be applied in a single coat using a metal spatula by spreading an even layer not thicker than 2 mm and it is finished using a plastic or sponge trowel, cloth or other tool depending on the desired aesthetic effect. In order to maintain chromatic uniformity, it is advisable not to moisten the product during the refinishing phase and to avoid resumption of processing.

PACKAGE: 30 Kg sack

DEHUMIDIFICATION AND WATERPROOFING

FINISHING AND LEVELING

TF01/TF02/TF04

TECHNICAL CHARACTERISTICS: TF is a breathable finishing in FENIX NHL 5 certified natural hydraulic lime and selected dolomitic aggregates, available in three different granulometries (from 0.8 to 4 mm: TF 01, TF02, TF 04), suitable for finishing any type of interior and exterior surface. TF does not form any vapor barrier and it is solvents free. The low content of water soluble salts helps creating an even chromatic effect once cured. FIELD OF APPLICATION: TF is a finishing particularly suited for historical/safeguarding restorations and renovations thanks to its chemical-physical and aesthetic qualities that allow meeting the requirements of finishing based on slightly hydraulic binders. It can be used on any type of plaster in air lime or hydraulic binders, whether new or existing. ADVANTAGES: - typical hazelnut color - compatible with existing masonry - low content of water soluble salts HOW TO APPLY IT: TF can be applied manually using a metal spatula spread in a thin and even layer not thicker than 3 mm and it is finished using a plastic or sponge trowel, cloth or other tool depending on the desired aesthetic effect. The application of uneven finishing thicknesses or the application over heterogeneous surfaces that were not previously treated using a top plaster coat TA01 or TA02 is prone to the appearance of mark rings and uneven chromatic effects after drying.

PACKAGE: 30 Kg sack

FIELD OF APPLICATION: TFS1 is particularly suited in historical/safeguarding restorations and renovations thanks to its chemical-physical and aesthetic qualities that allow meeting the requirements of finishing based on slightly hydraulic binders. It can be used on any type of plasters in air lime or hydraulic binders, whether new or existing.

YIELD : 2÷3 Kg/m2

YIELD (TB01): 2÷3 Kg/m2

YIELD (TF02): 3÷5 Kg/m2

TECHNICAL CHARACTERISTICS: TFS1 is a waterproof finishing for exteriors, in FENIX NHL 5 certified natural hydraulic lime and selected aggregates, characterized by high breathability and weather resistance. TFS1 protects and increases the exterior plaster durability without forming barriers to vapor. The low content of water soluble salts helps creating an even chromatic effect once cured.

MIXING WATER: 0,23 l/Kg (approx.7 l/sack)

MIXING WATER: 0,23 l/Kg (approx 7 l/sack)

TFS1

ADVANTAGES: - waterproof and breathable - spreadable with ease - extremely low water absorption - compatible with existing masonry

HOW TO APPLY IT: TB must be spread by metal trowel and finished with a metal plastering trowel (sanding), plastic trowel, sponge trowel or with other tools depending on the type and degree of desired finishing. It can be subsequently painted or left exposed. It is compatible with the subsequent application of setting coat, putty, marmorinos, stuccos, plastic or mineral coatings, tiles, wallpaper, etc. It can include fiberglass meshes in the creation of reinforced shavings on existing cracked plasters.

F I N E , M E D I U M , C OA R S E F I N I S H I N G IN N AT U R AL H Y DR A U LI C LI M E

WATERPROOF F INIS H ING IN NATU RA L H YDRA U L IC L IME

HYSTORICAL BUILDINGS

E XT R A FIN E , F I N E , M E DI U M , COA R S E W HITE TO P C OAT P LASTE R

FINISHING AND LEVELING

WATERPROOF BREATH A BL E PL A S TERING MORTA R

T30S

TECHNICAL CHARACTERISTICS: T30S is a waterproof and breathable mortar in FENIX NHL 5 certified natural hydraulic lime and selected dolomitic aggregates particularly suited for the construction of exterior wainscots. T30S is suitable for the recovery of masonry damaged by rising humidity since it combines the breathability of natural hydraulic lime with noticeable waterproofing action. T30S is compliant to UNI EN 998-1 “Specifications for mortar for masonry – interior and exterior plaster mortars" and it is subject to CE marking in accordance to the regulations in force. FIELD OF APPLICATION: T30S allows the recovery of masonry damaged by rising humidity by capillarity or in any case the recovery of all the masonry structures where the durability of plaster is significantly compromised by humidity. T30S can be applied to any masonry structure where mortar’s high breathability, extremely low water absorption by capillarity and high chemical/physical characteristics are required. ADVANTAGES: - waterproof - breathable - extremely low content of water soluble salts HOW TO APPLY IT: preparation of preliminary rendering using T30V in order to even out the surface in anticipation of the application of plastering body; subsequent T30V plaster application mixed with water in a 2 to 3 cm thick single coat. WATER CAPILLARY ABSORPTION (UNI EN 1015-18): classe W2: c < 0,05 Kg/(m2 x min0,5) YIELD (for plaster): approx. 18 Kg/(m2 x cm) MIXING WATER: 0,16 l/Kg (approx.5 l/sack) PACKAGE: 30 kg sack or loose in silos

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

HISTORICAL BUILDINGS

HISTORICAL BUILDINGS STONE ELEMENTS RECONSTRUCTION

TLast-100

D E HU MID IFYI N G A N D R E CLA I M I N G TR EATM E NT

TECHNICAL CHARACTERISTICS: TLast-100 is a macro-porous dehumidifying cycle for the reclamation of damaged masonry due to the combined effect of rising humidity and salt presence. TLast-100 is a reclaiming cycle that includes the application of the following products: - TSal/TSal VP: Anti-salt treatment (recommended in case of surfaces with salt content); - TLast-100 RINZAFFO: is a ready to use rendering in FENIX NHL 5 certified natural hydraulic lime and selected dolomitic aggregates from 0 to 2 mm; - TLast-100 INTONACO: macro-porous plaster in FENIX NHL 5 certified natural hydraulic lime and light selected aggregates from 0 to 3 mm.

Weather humidity

Condensation damp

TLast-100 INTONACO macro-porous structure ensures high breathability and the disposal and evaporation of water absorbed by the material; these characteristics remain unaltered by the barrier effect offered by the anti-salt treatment and preliminary rendering at the time of macro-porous plaster’s application. TLAST-100 INTONACO is compliant to UNI EN 998-1 "Specifications for mortar for masonry – interior and exterior plaster mortars" and it is subject to CE marking in accordance to the regulations in force. FIELD OF APPLICATION: TLast-100 is a dehumidifying cycle for the restoration of any masonry surface, whether new or old and subject to rising humidity and the presence of salts, requiring the use of high breathability products and water drainage ability, low capillary absorption and extremely low content of water soluble salts. TLast-100 can be applicable both on interior and exterior masonry.

Upward damp

Seepage damp

COMPLIANT WTA

technical data TLAST-100

yield capillary water absorption in 24 h (W24) (UNI EN 1015-18) full porosity vapor diffusion resistance(UNI 9233) package

T-STONE

TECHNICAL CHARACTERISTICS: T-STONE is a special product based on hydraulic binders and selected aggregates, featuring enhanced adherence and controlled shrinkage with low content of water soluble salts, suitable for the restoration of damaged stone elements. T-STONE features easy workability and pliability; it is resistant to frosting and defrosting cycles and to thermal stress at the joints of stone elements. T-STONE is suitable for chromatic hues studies in order to reduce the visual impact of partial reconstruction or renovation operations. FIELD OF APPLICATION: T-STONE is specifically formulated for the restoration and reconstruction of stone elements ADVANTAGES: - controlled shrinkage - high workability - possibility of achieving specific color tones HOW TO APPLY IT: T-STONE is applied manually and processed using a trowel, spatula, or other tool suitable to shape and finish the installed product as desired. MIXING WATER: 0,18 l/Kg (approx.5.5 l/sack) Yield: approx.19-20 Kg/(m² x cm) PACKAGE: 30 kg sack

ADVANTAGES: - high water drainage capacity - it meets WTA guideline requirements - compatible with existing masonry - it contains FENIX NHL 5 HOW TO APPLY IT: sanding of the surface being worked on, using TSal or TSal VP anti-salt products, as per instructions described in the technical specification sheet; application of TLast-100 RINZAFFO rendering (after approximately 12 hours) in order to even out any uneven surface and to create smooth bridge bonds. Application of TLast-100 PLASTER (after 12 – 14 hours) with a variable thickness from a minimum of 20 mm up to 30 to 40 mm to be applied in a single coat.

mixing water

S PECIA L PRODU CT FOR S TONE EL EMENTS RECONS TRU CTION

HYSTORICAL BUILDINGS

DEHUMIDIFICATION AND WATERPROOFING

TLAST-100 RINZAFFO

TLAST-100 INTONACO

approx. 0,21 l/Kg (approx. 6,5 l/sack)

approx. 0,35 l/Kg (approx. 7 l/sack)

approx. 6 Kg/m2

approx. 12 Kg/(m2 x cm)

C > 0,3 Kg/m2

35%

70%

7÷8

30 kg sack

25 kg sack

THERMAL INSULATION NATU RA L TH ERMA L PL A S TER

TERMO-BI

TECHNICAL CHARACTERISTICS: TERMO-BI is a thermal insulating, fiber-reinforced, natural plaster with low specific weight, in natural hydraulic lime BIO-E NHL 5 certified and selected perlites and expanded silicons. TERMO-BI combines excellent ease of applicability to its low thermal conductivity and excellent breathability. This plaster has the quality of being able to hinder heat exchange while maintaining a high average temperature within the wall and the interior wall surface, improving energy savings and environmental comfort. It is compliant to UNI EN 998-1 "Specifications for mortar for masonry - interior and exterior plaster mortars" and it is subject to CE marking in accordance to the regulations in force. FIELD OF APPLICATION: TERMO-BI must be used to create machine processed natural and breathable plasters for exteriors with a thickness greater than 2 cm for any type of surface. Thanks to its natural features and extremely low presence of water soluble salts TERMO-BI can be used also in the renovation of historical sites whenever thermal insulation is required. ADVANTAGES: - highly insulating - compatible with historical masonry - it contains BIO-E NHL 5 - a natural alternative to plate insulation HOW TO APPLY IT: TERMO-BI must be applied using a plastering machine for ready-to-use plaster and applied directly to the wall using a post screed. THERMAL CONDUCTIVITY(EN 12667): class T1 - λ = 0,091 W/(m x °K) MIXING WATER: approx.0.7 l/Kg (approx.9 l/sack) YIELD: approx.4Kg/(m² x cm) PACKAGE: 13 kg sack

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

1 – BINDERS

natural hydraulic lime _BIO-E NHL5 lime putty _Grassello

NATURAL BUILDINGS

4 – FLOORS

floor screeds _BIO-E/FONDO _BIO-E/SOFT bonding agents _TADP/C

2 - MASONRY AND PARTITIONS

5 - THERMAL INSULATION

thermal plaster _TERMO/BI cladding bonding agents _TK01/Ch cladding in natural cork _T-GREEN

NATURAL BUILDINGS

mortars _BIO-E/RC _BIO-E/P2 plasters _BIO-E/RC _BIO-E/P _BIO-E/P1

3 - FINISHING AND LEVELING

top coat plaster _BIO-E/RASANTE finishing _BIO-E/FINITURA

Regina dei Prati Resort Villaraspa di Mason Vicentino (VI) - Italy

Construction and renovation of buildings following the sustainable housing standards. Farmsteads, farmhouses and buildings following Leed and CasaClima criteria.

Ethical wellbeing and human accountability: these are two defining elements of Tassullo’s policies. Products that are pure, rich in heritage and additives-free to safeguard health and the environment and to make home even a better place. The BIO-E® Calcebenessere line is the best example of this philosophy: A complete range of high quality materials in natural hydraulic lime with unmatched performance, fully natural, breathable and eco-friendly. LEED

www.calcebenessere.it

PRODUCT DATA SHEETS > 79

LOAD BEARING MASONRY SYSTEM

CLADDING SYSTEM

BIO-E/RC mortar BIO-E/RC mortar

MASONRY PARTITIONING SYSTEM

BIO-E/P2 mortar

FLOOR SYSTEM

TADP/C adhesive

TK01/Ch adhesive BIO-E/P1 plaster

T-GREEN insulating panel in cork TK01/Ch with armor mesh

Bio-E/Finitura

TF1000

Bio-E/Fondo base floor screed Bio-E/Soft filling floor screed

NATURAL BUILDINGS

Bio-E/Rasante

BIO-E/P1 plaster

NATURAL BUILDINGS Systems and applications 80

LEED

NATURAL BUILDINGS

BINDERS N H L 5 C E RTIFIE D NATURAL H Y DRAULIC LIME

BIO-E NHL5

BEDDING MORTA R A ND CONS OL IDATING RENDERING

MORTA RS

BIO-E/RC

TECHNICAL CHARACTERISTICS: BIO-E NHL5 is a natural hydraulic lime accurately selected, free from additives and cutting; it is NHL 5 certified as per UNI EN 459-1. BIO-E is a NHL 5 natural hydraulic lime manufactured by Tassullo in Italy, (as proven by the FCP manufacturing certification and CE mark) featuring extremely high quality and purity, obtained by firing exclusively local marl-limestone (calcium carbonate and clay) extracted using modern technologies from natural banks, accurately following the teachings of our heritage. BIO-E does not contain either cement or any other derivative, as certified by ICMQ (Certification of Manufacturing Inspection at the Factory) and by the Department of Materials Engineering of the University of Trento.

TECHNICAL CHARACTERISTICS: BIO-E/RC is a ready-to-use grout in FENIX NHL 5 certified natural hydraulic lime and selected dolomitic aggregates particularly suited for the construction of consolidation renderings, load bearing masonry bedding, filling mortars, infilling and locking. The unique purity of the binding agent and the lack of cement and organic additives make BIO-E/RC ideal for use in constructions performed according to sustainable housing guidelines. When used as bedding mortar, BIO-E/RC is compliant to UNI EN 998-2 “Specifications for mortar for masonry – interior and exterior plaster mortars”. When used as rendering and plaster, BIO-E/RC is compliant to UNI EN 998-1 “Specifications for mortar for masonry – interior and exterior plaster mortars”

FIELD OF APPLICATION: BIO-E is the basis for the best sustainable housing mortars and for all the products that are part of the Tassullo BIO-E Calcebenessere line. BIO-E is suitable for yard preparation of high quality mortars for sustainable housing construction, more specifically: natural mortars for bedding of brick masonry, stone, solid brick, and for creating floor screeds bases featuring high breathability and workability finishes, capable of offering excellent hygrometric control of the environments for improved living comfort.

FIELD OF APPLICATION: BIO-E/RC is a grout that must be used as a consolidating rendering and “if necessary” it can be reinforced. For application to stone masonries weakened by the loss of bedding mortar and where there is the need to restore mortar joints, lock in place non cohesive stones, or create bedding for load bearing masonry in brick. It can be applied both in interiors and exteriors. ADVANTAGES: - all natural - it contains BIO-E NHL 5 - certified mechanical strength - it allows quick application

ADVANTAGES: - natural and fully recyclable - NHL 5 certified as per UNI EN 459-1 - NHL with the lowest natural radioactivity - made in Italy with selected marl - highly breathable, it improves living comfort - without cement and additives

HOW TO APPLY IT: BIO-E/RC can be applied manually or using a plastering machine suitable for traditional mortars with granulometry up to 4 mm.

NATURAL BUILDINGS

HY D R AU L IC LI M E

MASONRY AND PARTITIONS

MIXING WATER: approx.0.15 l/Kg (approx.4.5 l/

HOW TO APPLY IT: BIO-E must be mixed with clean and selected aggregate, free from organic substances, at the rate of 350/450 Kg/m3 and clean water depending on the desired consistency of the mix. The mix can be prepared manually or by concrete mixer. The plaster preparation at the yard can be applied manually or by plastering machine suitable for the type of aggregate and mix prepared. In case of plaster preparation, the rough surface must be trowelled after propping.

MECHANICAL STRENGTH: class M5 (> 5 N/mm2) UNI EN 998-2 class CSIV (> 6 N/mm2) UNI EN 998-1 PACKAGE: 30 kg sack or loose in silos

MIXING WATER: approx. 1100 kg/m3 MECHANICAL STRENGTH: > 5 N/mm2

MASONRY AND PARTITIONS

PACKAGE: 25 kg sacks

MORTA RS

BINDERS AIR L IM E

LI ME P UTTY

GRASSELLO

TECHNICAL CHARACTERISTICS: TASSULLO GRASSELLO is a pure air lime paste obtained from processing quicklime in a tank for over a month. GRASSELLO is compliant to UNI EN 459-1 "Building lime. Definitions, specifications and conformity criteria" classified as Cl-80 S and subject to CE marking according to regulations in force. FIELD OF APPLICATION: GRASSELLO can be used in addition to natural lime BIO-E NHL 5 in preparation of finishing or mortars at the yard. Adding TASSULLO GRASSELLO to hydraulic mortar increases its workability and plasticity. ADVANTAGES: - certified - natural

PA RTITIONING MORTA R

BIO-E/P2

TECHNICAL CHARACTERISTICS: BIO-E/P2 is breathable mortar in FENIX NHL 5 certified natural hydraulic lime and selected dolomitic aggregates suitable for the preparation of plastering, filling, and infilling mortars as well as for bedding and plastering of exposed surface bricks. The unique purity of the binding agent and the lack of cement and organic additives make BIO-E/P2 ideal for use in constructions performed according to sustainable housing construction guidelines. BIO-E/P2 is compliant to UNI EN 998-1 "Specifications for mortar for masonry – interior and exterior plaster mortars" and it is subject to CE marking in accordance to the regulations in force. FIELD OF APPLICATION: BIO-E/P2 can be applied to any type of surface, both in interiors and exteriors. It allows applying plaster for interiors and/or exteriors on vertical walls or ceilings in 15/20 mm layers, infilling, filling and bedding of partitioning or exposed surface bricks. ADVANTAGES: - all natural - it contains BIO-E NHL 5 - certified mechanical strength - it ensures mix consistency

YIELD: approx. 2 Kg/m²

HOW TO APPLY IT: BIO-E/P2 must be applied following application methods used for conventional mortars. If it is used to create plasters it can be applied by hand or through an appropriate plastering machine. It must be finished using a post and plastic trowel.

PACKAGE: 25 kg sack in Big Bags, large cases or pallets

MIXING WATER: approx.5.5 l/30 kg sack MECHANICAL STRENGTH: M 2,5 ( 2.5 - 5 N /mm2) PACKAGE: 30 kg sack or loose in silos

Please see data sheet for a full overview of application notes, method of use and application warnings

NATURAL BUILDINGS

NATURAL BUILDINGS FINISHING AND LEVELING

P L AST E R S

M A NUAL P LASTE R

BIO-E/P

TOP COAT PL A S TERS

BIO-E/RASANTE

TECHNICAL CHARACTERISTICS: BIO-E/RASANTE is a breathable top coat plaster in natural hydraulic lime BIO-E NHL 5 and selected dolimitic aggregates. The high elasticity and adhesion capability, the low content of water soluble salts and its breathability make this product suitable for the preparation of base plaster and finishing. BIO-E RASANTE is cement and resin free, it is breathable and it aids the hygrometric control of the environments.

TECHNICAL CHARACTERISTICS: BIO-E/P is a breathable mortar in FENIX NHL 5 certified natural hydraulic lime and dolomitic aggregates suitable for the preparation of rendering mortars, plasters, filling, infilling and bedding of bricks. The unique purity of the binding agent and the lack of cement and organic additives make BIO-E/P ideal for use in constructions performed according to sustainable housing guidelines. BIOE/P is compliant to UNI EN 998-1 "Specifications for mortar for masonry – interior and exterior plaster mortars" and it is subject to CE marking in accordance to the regulations in force.

FIELD OF APPLICATION: BIO-E/RASANTE can be applied over BIO-E plasters (BIO-E/P1, BIO-E/P, TERMOBI) or on any other rough plaster in air lime or hydraulic binder. Thanks to the high adhesion, whenever required, it can be used as a rendering bonding bridge on reinforced concrete prior to applying the plaster.

FIELD OF APPLICATION: BIO-E/P can be applied to any surface, as long as it is free from impurities and it allows creating plasters for interiors and/or exteriors on vertical walls or ceilings in 15/20 mm layers, infilling, filling and bedding of bricks.

ADVANTAGES: - high elasticity and adhesion - high breathability - free from cement and synthetic resins - it contains BIO-E NHL 5

ADVANTAGES: - all natural - it contains BIO-E NHL 5 - certified mechanical strength - it ensures mix consistency

HOW TO APPLY IT: BIO-E/RASANTE must be spread by metal trowel and finished with a metal plastering trowel (sanding), plastic or sponge trowel, or with other tools depending on the type and degree of desired finishing.

HOW TO APPLY IT: BIO-E/P can be applied manually or by using any automatic system suitable for traditional mortars with granulometry up to 4 mm and it must be finished using a post and plastic trowel. When used as a plaster for interiors or exteriors, it is advisable to apply, initially, a layer of BIO-E/P (rendering) in order to prepare the masonry for the subsequent plaster layer, which will be applied after approximately 12/24 hours. Apply it in subsequent layers of 15 – 20 mm each.

MIXING WATER: approx.6.5 l/sack

NATURAL BUILDINGS

MASONRY AND PARTITIONS

YIELD: approx. 3 Kg/m²

MIXING WATER: approx. 0,15 l/Kg (approx. 4,5 l/sack)

PACKAGE: 30 kg sacks

MECHANICAL STRENGTH: class CSIII (from 3,5 to 7,5 N/mm2) PACKAGE: 30 kg sack and loose in silos

FINISHING AND LEVELING

MASONRY AND PARTITIONS P L AST E R S

S P RAYING P LASTE R

BIO-E/P1

TECHNICAL CHARACTERISTICS: BIO-E/P1 is a breathable mortar in FENIX NHL 5 certified natural hydraulic lime and dolomitic aggregates, specifically designed for machine application, suitable for the creation of plasters for interiors and exteriors. It is cement free and it is characterized by high spreadability and workability without the need of using synthetic additives. The high breathability typical of BIO-E NHL 5 natural hydraulic lime hinders the formation of molds and it aids the hygrometric control of the environments. BIO-E/P1 is compliant to UNI EN 998-1 "Specifications for mortar for masonry – interior and exterior plaster mortars" and it is subject to CE marking in accordance to the regulations in force. FIELD OF APPLICATION: BIO-E/P1 is applicable to any even smooth and dry surface, as long as it is free from dust, salt efflorescence, uneven elements, oils, molds, organic material etc. BIO-E/P1 allows applying plasters on vertical walls and ceilings in 10/15 mm layers. ADVANTAGES: - high breathability and hygroscopicity - all natural - it contains BIO-E NHL 5 - it allows a quick application HOW TO APPLY IT: BIO-E/P1 is easy and fast to apply and to spread on the plaster surface compared to plastering mortars prepared at the yard. BIO-E/P1 can be finished at will using a post, American trowel or sponge. MIXING WATER: approx.0.21 l/Kg (approx.6.5l/sack) YIELD: approx.13.5 Kg/(m² x cm)

F INIS H ES

F INIS H ING

BIO-E/FINITURA

TECHNICAL CHARACTERISTICS: BIO-E/FINITURA is a finishing in natural hydraulic lime BIO-E and aggregates with a maximum granulometry of 0.8 mm. Its high elasticity and adhesion capability, its low content of water soluble salts and breathability make this product suitable for the finishing of plasters in natural hydraulic lime, achieving great advantages in terms of hygrometric control of the environments. BIO-E FINISHING is cement and resin free. FIELD OF APPLICATION: BIO-E/FINITURA can be applied over BIO-E plasters or on any other rough plaster in air lime or hydraulic binder as long as they are free from dust and uneven elements. ADVANTAGES: - high finishing level - high elasticity and adhesion - free from cement and synthetic resins - it contains BIO-E NHL 5 HOW TO APPLY IT: BIO-E/FINITURA, thanks to the high chemical reactivity at the presence of salts, is suitable for application to any type of clean surface, free from dust, salts and uneven elements. BIO-E/ FINITURA can be finished at will using any type of breathable paint for interiors or exteriors. MIXING WATER: approx.6.5 l/sack YIELD: approx.3 Kg/m² PACKAGE: 30 kg sacks

PACKAGE: 30 kg sack and loose in silos

Please see data sheet for a full overview of application notes, method of use and application warnings

NATURAL BUILDINGS

NATURAL BUILDINGS FLOORS

FLOORS F LO O R SC RE E D

BIO-E/FONDO

BONDING AGENTS

BONDING AGENT FOR TIL ES

TADP/C

TECHNICAL CHARACTERISTICS: BIO-E/FONDO is a ready-to-use grout in BIO-E NHL 5 certified natural hydraulic lime suited for the construction of natural and breathable floor screeds for civil use that can be finished using ceramic, stone, wooden flooring etc. BIO-E FONDO is free from cement and additives.

TECHNICAL CHARACTERISTICS: TADP/C is a clear and natural adhesive for ceramic tiles, stoneware, fired brick, natural stone (marble, granite) in BIO-E NHL 5 certified natural hydraulic lime characterized by high resistance, high adhesion, excellent workability, breathability and durability over time also under critical conditions such as moist environments or environments subject to strong thermal fluctuations.

FIELD OF APPLICATION: BIO-E/FONDO is a breathable and natural grout to be used for the installation of floor screeds for civil use with a variable thickness in the range of 4 to 12 cm. BIO-E FONDO is applicable on standard floors, on sub-bases or foundations with or without thermal insulation or on infilling floor screeds. When fully cured, BIO-E FONDO will be able to accept any type of flooring: tiles, wood, stone slabs, bricks etc.

FIELD OF APPLICATION: TADP/C can be applied over floor screeds with or without a radiant heating system and BIO-E NHL 5 plasters or other hydraulic binder, on any rough plaster in air lime or hydraulic binder as long as they are consistent and dust free.

ADVANTAGES: - all natural - cement and additives free - it contains BIO-E NHL 5 - CE marking in compliance to the regulations in force

TADP/C

ADVANTAGES: - high resistance - high adhesion - natural and breathable - cement and additives free - it contains BIO-E NHL 5

HOW TO APPLY IT: BIO-E/FONDO must be applied to moist soil, then spread and finished using a post and plastic trowel following standard procedures used for traditional floor screeds.

HOW TO APPLY IT: TADP/C can be applied using a shaped trowel over the application surface of the tile, both horizontally and vertically.

MIXING WATER: approx.0.15 l/Kg (approx.4.5l/sack)

MIXING WATER: 0.25 l/Kg (approx.7.5 liters /sack)

YIELD: approx.18 Kg/(m² x cm)

YIELD: 4 Kg/m22

PACKAGE: 30 kg sacks

INITIAL TRACTION ADHESION: > 0,5 N/mm2 (UNI EN 1348)

NATURAL BUILDINGS

FLOOR SC R E E DS

PACKAGE: 30 kg sacks

THERMAL INSULATION

FLOORS FLOOR SC R E E DS

F LO O R SC RE E D FO R FILLING

BIO-E/SOFT

TECHNICAL CHARACTERISTICS: BIO-E/SOFT is a fiber reinforced natural grout in BIO-E NHL 5 certified natural hydraulic lime and light aggregates to be used as insulating and infilling sub-base between the floor and the floor screed of the floor built using BIO-E FONDO or using BIO-E and sand at the yard. BIO-E SOFT is free from cement and additives. FIELD OF APPLICATION: BIO-E/SOFT is applicable on lightened natural breathable floor screeds to be installed between the floor and the floor screed. ADVANTAGES: - light, it does not add weight to the structures - excellent soundproofing - cement and additives free - it contains BIO-E NHL 5 BIO-E/SOFT

HOW TO APPLY IT: BIO-E/SOFT must be spread with a thickness greater than 2-3 cm directly over the floor and the piping, making sure to match the level requirements using a rake, post or trowel depending on the consistency of the mix. MIXING WATER: 13 - 16 liters /sack YIELD: 8 Kg/(m² x cm) COMPRESSION RESISTANCE (UNI EN 1015-11): approx.1.2 N/mm² PACKAGE:13 kg sacks

TH ERMA L PL A S TER

NATU RA L TH ERMA L PL A S TER

TERMO-BI

TECHNICAL CHARACTERISTICS: TERMO-BI is a thermal insulating, fiber-reinforced, natural plaster with low specific weight, in natural hydraulic lime BIO-E NHL 5 certified and selected perlites and expanded silicons. TERMO-BI combines excellent ease of applicability to its low thermal conductivity and excellent breathability. This plaster has the quality of being able to hinder heat exchange while maintaining a high average temperature within the wall and the interior wall surface, improving energy savings and environmental comfort. TERMO-BI is compliant to UNI EN 998-1 "Specifications for mortar for masonry interior and exterior plaster mortars" and it is subject to CE marking in accordance to the regulations in force. FIELD OF APPLICATION: TERMO-BI must be used to create machine processed natural breathable plasters for exteriors with a thickness greater than 2 cm for any type of surface. Thicknesses greater than 4 cm can be achieved by applying several coats. ADVANTAGES: - highly insulating - suitable for any type of surface - high consistency and durability over time - it contains BIO-E NHL 5 - a natural alternative to plate insulation - CE marking in compliance to the regulations in force HOW TO APPLY IT: TERMO-BI must be applied using a plastering machine for ready-to-use plaster and applied directly to the wall using a post screed. MIXING WATER: approx.0.7 l/Kg (approx.9 l/sack) YIELD: approx. 4Kg/(m² x cm) THERMAL CONDUCTIVITY(EN 12667): class T1 - λ = 0,091 W/(m x °K) PACKAGE: 13 kg sacks

Please see data sheet for a full overview of application notes, method of use and application warnings

NATURAL BUILDINGS

THERMAL INSULATION C L AD D IN G IN N ATU R A L CO R K

TK01/Ch

B O N D ING TO P C OAT P LASTE R FO R C LAD D ING

TECHNICAL CHARACTERISTICS: TK01/Ch is a breathable and natural bonding agent in BIO-E NHL 5 natural hydraulic lime, selected aggregates and cellulose. TK01/Ch is compliant to the ETAG 004 European guidelines. FIELD OF APPLICATION: TK01/Ch is used to install breathable thermal insulation panels in cork, rock wool, wood fiber, mineralized wood, calcium silicate and subsequently in the preparation of the surface in anticipation of the finishing. The physical characteristics of the product and in particular its high breathability offer significant advantages in terms of hygrometric control of the environments. ADVANTAGES: - high elasticity and adhesion - high breathability - free from cement and synthetic resins - compliant to ETAG 004 - it contains BIO-E NHL 5

MIXING WATER: approx. 6 – 6.5 l/sack

NATURAL BUILDINGS

HOW TO APPLY IT: when used as a bonding agent: apply it between panel and surface in such quantities to ensure good adhesion and stability to the system (4-5 kg/m²). It is advisable to apply the bonding agent near to the external perimeter of the panel and in 4 -5 points within it. When used as leveling: apply it on the exterior surface of the panel glued and locked using appropriate fastening by spreading a first layer of bonding agent using a toothed metal spatula then apply a fiberglass mesh with a weight greater than 130 g/m² and proceed to further leveling adding material, if required, in order to incorporate the mesh in the leveling surface layer and make the surface as even as possible in anticipation of the finishing. YIELD: for bonding 4 ÷ 5 Kg/m² for leveling: approx. 3 Kg/m²

Adhesion to cork panel (ETAG 004): > resistant to block tensile stress PACKAGE: 25 kg sacks

natural hydraulic lime

high adhesion

high spreadability

without cement and additives

THERMAL INSULATION C L AD D IN G IN N ATU R A L CO R K

I N SULATING PANEL I N NATURAL C O RK

T-GREEN

TECHNICAL CHARACTERISTICS: T-GREEN is an insulating panel in natural cork aggregate to be used in combination with natural TK01/Ch bonding/top coat plaster. It is a material that distinguishes itself for its naturalness, recyclability, breathability, waterproofing, anti condensation, anti-mold, putrid-proof, flame retardant, odorless, weather resistant, acid resistant, critters resistant qualities and the highest resistance to aging. FIELD OF APPLICATION: ideal for installation of cladding thermal insulation systems type TASSULLO GREEN SYSTEM: Set up an even bonding of the slab surface. Alternatively arrange for perimeter and diagonal bonding. Mechanical locking must be arranged and performed using at least 6 nails for each m². Then it is necessary to perform leveling using a metallic trowel with a thickness of at least 5 mm to be left drying and to be finished after 24/48 hours using two coat leveling with a fiberglass mesh that is alkali resistant and suitable to the finishing system. ADVANTAGES: - all natural - breathable and recyclable - highly insulating VAPOR DIFFUSION RESISTANCE: µ = from 5 to 30 DECLARED THERMAL CONDUCTIVITY: λ = 0,040 m/(m x °K) PANEL SIZE: panel size (mm): 1000 x 500 thickness (mm) : 20 – 30 – 40 – 50 – 60 – 70 – 80 – 100 - 120.

Residence Regina dei Prati – Interior Details Please see data sheet for a full overview of application notes, method of use and application warnings

1 - CONSOLIDATION AND RESTORATION _TCA3/T

3 - WATERPROOFING

_IDROTASS

REINFORCED CONCRETE BUILDINGS

_TCA3/C _TCA-MI _TCA1

3 - PROTECTIVE SYSTEM

_TC-Paint _Ti-253

2 - FASTENING AND RECONSTRUCTION

_ T-FLASH/FR

_TP-551

5 - THERMAL INSULATION

_TERMO-TASS _ISI-THERM

CONCRETE BUILDINGS

_RED SYSTEM

Renovation of residential, industrial, multipurpose reinforced concrete buildings

Tassullo products for the renovation and restoration of reinforced concrete buildings offer a solution to all the challenges met at the yard: unique products, technologically advanced and capable of guaranteeing the best performance.

PRODUCT DATA SHEETS > 90

BUILDINGS IN CONCRETE

BUILDINGS IN CONCRETE CONSOLIDATION AND RESTORATION

TCA3/T

F I B E R - R E I N FO R C E D M O R TA R FOR L IG HT S TR U CTU R A L CO N CR E TE ( LSC ) RE STO RATIO N

PASSIVATING FIBER-REINFORCED MORTAR FOR RES TORATION OF S TEEL BA R COVER

TCA-MI

TECHNICAL CHARACTERISTICS: TCA3/T is a fiber reinforced thixotropic mortar in natural hydraulic lime, selected aggregates with a maximum granulometry of 4 mm, and additives. TCA3/T is a mortar characterized by high adhesion, low permeability to carbon dioxide and to water and controlled shrinkage. TCA3/T is compliant to Italian Ministerial Decree10/05/2004.

TECHNICAL CHARACTERISTICS: TCA-MI is a hydraulic binders-based thixotropic fiber-reinforced mortar, polymer modified, featuring controlled shrinkage, high adhesion and corrosion inhibitors, combined with additives and selected aggregates having a maximum granulometry of 4 mm. TCA-MI is in compliance with the Italian Ministerial Decree 10/05/2004.

FIELD OF APPLICATION: TCA3/T is used for the reconstruction of bar covers during repairs and restoration of reinforced concrete structures or in the cases where it is necessary to apply thixotropic mortar with high mechanical characteristics and controlled shrinkage.

FIELD OF APPLICATION: TCA-MI is a special mortar for the reconstruction of reinforced concrete portions deteriorated by corrosion on the metal armor.

ADVANTAGES: - controlled shrinkage - high adhesion - extremely low permeability to agressive agents(such as water, salts and carbon dioxide)

ADVANTAGES: - fiber-reinforced - controlled shrinkage - high adhesion - nitrites free

HOW TO APPLY IT: TCA3/T is applied manually or using adequate automatic equipment suitable for mortars with a maximum granulometry of 4 mm.

HOW TO APPLY IT: TCA-MI can be applied manually or using plastering machines, in one or more coats having a thickness of approximately 2 cm each.

MIXING WATER: approx. 0.17 l/Kg (approx. 5 l/sack)

MIXING WATER: approx. 0.16 l/Kg (approx. 5 l/sack)

COMPRESSION RESISTANCE (UNI EN 1015-11): approx. 33 N/mm²

28 days COMPRESSION RESISTANCE (UNI EN 1015-11): approx. 43 N/mm²

ELASTIC COMPRESSION MODULE (UNI 6556): approx. 26.000 N/mm²

ELASTIC COMPRESSION MODULE (UNI 6556): approx. 28.500 N /mm²

PACKAGE: 30 kg sack and loose in appropriate silos

CONCRETE BUILDINGS

CONSOLIDATION AND RESTORATION

TCA3/C

CAST ING MO R TA R FO R F I LLI N G

ANTI-CARBONATION TOP COAT PLASTER FOR REINFORCED CONCRETE S TRU CTU RES

TCA1

TECHNICAL CHARACTERISTICS: TCA3/C is a rheoplastic polymer mortar (plastic and flowing) modified on the basis of hydraulic lime, selected aggregates with a maximum granulometry of 4 mm, and additives. TCA3/C after being mixed with just water offers great fluidity, stability, high resistance and quick hardening qualities. TCA3/C is compliant to Italian Ministerial Decree10/05/2004.

TECHNICAL CHARACTERISTICS: TCA1 is a special top coat plaster in hydraulic binders, selected fine aggregates and additives. The significant priming power and low permeability to carbon dioxide and water make TCA1 particularly suitable for protective leveling of concrete structures. TCA1 is compliant to Italian Ministerial Decree 10/05/2004.

FIELD OF APPLICATION: TCA3/C is used for the repairing of reinforced concrete structures or in the cases where it is necessary to work with a fluid and high mechanical characteristics mortar. TCA3/C is suitable for the fastening of clamps, anchor rods, metal structures and machine bases.

FIELD OF APPLICATION: TCA1 is used as top coat plaster on concrete surfaces or slabs or over renovation mortar in restoration works of deteriorated concrete structures. TCA1 extends the duration of the passive conditions of metal armors in concrete by preventing or delaying corrosion.

ADVANTAGES: - fluid and smooth - plastic - resistant - quick drying

ADVANTAGES: - highly protective - low water and carbon dioxide permeability - it can be left exposed as a finishing

HOW TO APPLY IT: TCA3/C must be poured in appropriate formworks or molding by its own weight or injected using appropriate equipment.

HOW TO APPLY IT: TCA1 is applied on a concrete or cement plasters. The mixture must be spread using a thin metal trowel and it is subsequently leveled or worked using a sponge trowel. MIXING WATER: approx. 0.25 l/Kg (approx. 7.5 l/sack)

MIXING WATER: approx. 0.16 l/Kg (approx. 5 l/sack)

YIELD: 2÷3 Kg/mm2

COMPRESSION RESISTANCE (UNI EN 1015-11): approx. 37 N/mm²

PACKAGE: 30 kg sack

ELASTIC COMPRESSION MODULE (UNI 6556): approx. 26.000 N/mm² PACKAGE: 30 kg sack and loose in appropriate silos

high fluidity

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

fast hardening

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

BUILDINGS IN CONCRETE

CONSOLIDATION AND RESTORATION P R OT E CT I V E PA I N T I N G FOR R E IN FO R CE D CO N CR E TE S TR U CTU RE S

FASTENING AND RECONSTRUCTION

TC-Paint

T-FLASH/FR

HIGH RESISTANCE QUICK DRYING MORTAR FOR FA S TENING A ND RECONS TRU CTIONS

TECHNICAL CHARACTERISTICS: T-FLASH/FR is a ready thixotropic product with high mechanical strength, quick setting and hardening features, suitable for fastening masonry, metal or plastic components and for the reconstruction of concrete or mortar with high hydraulic resistance (profiles, corners, concrete cover, etc.). The product’s setting and hardening speed as well as its workability, allow it to be used for filling or reconstructions, with controlled shrinkage and high thickness and finishing applicable after few minutes (approx. 30 minutes). T-FLASH FR is compliant to Italian Ministerial Decree10/05/2004.

TECHNICAL CHARACTERISTICS: TC-Paint is a product in styrene-acrylic polymers in water dispersion. It is highly resistant to water, vapor, carbon and sulfurous dioxide. TC-PAINT avoids the risk of corrosion on armor rods. TC-Paint maintains breathability to water vapor in compliance to DIN 4108 3 standards. FIELD OF APPLICATION: TC-Paint is suitable for the protection and finishing of concrete structures or fiber cement whether protected or exposed to the weather (indoors or outdoors) ; it must be used in the renovation of reinforced concrete structures subject to degradation as a consequence of the corrosion of the metal reinforcing structure.

FIELD OF APPLICATION: T-FLASH/FR is ideal for fastening drain covers, clamps, hooks, rods, metal rods, pins, threaded rods, chains and positioning/locking pipes, railings, grilles, grates, for the filling or reconstruction of edges, string courses, window outlines in concrete or resistant cement mortar. It can be used both for interiors and exteriors.

ADVANTAGES: - highly protective - vapor and carbon dioxide resistant - it can be used as a finishing

ADVANTAGES: - quick setting and hardening - high mechanical strength - plastic and workable - immediate finishing - supplied in sealed sack

HOW TO APPLY IT: TC-Paint can be applied by roller or spry gun or by brush SPECIFIC WEIGHT: 1,45 Kg/l YIELD: 0,5 l/m2

HOW TO APPLY IT: T-FLASH/FR is applied by hand with a spatula or trowel, paying attention to fill the edges first and then the whole body of the gap. Plasticity and workability of the product allow performing high thicknesses in one coat (up to 5 - 6 cm) by operating vertically from bottom to top.

PACKAGE: 16 liter can

MIXING WATER: approx. 6 l/30 kg sack 28 days COMPRESSION RESISTANCE (UNI EN 1015-11): approx. 40 N/mm² MIX WORKABILITY TIME AT 20 °C: approx. 15 minutes

WATERPROOFING

CONSOLIDATION AND RESTORATION C OR R OSIO N I N H I B I TO R P R OTE CTI V E COAT

CONCRETE BUILDINGS

PACKAGE: 30 kg sack

Ti-253

IDROTASS

DU A L COMPONENT WATERPROOF L EVEL ING

TECHNICAL CHARACTERISTICS: Ti-253 is a primer for the corrosion protection of reinforced concrete and it prevents degradation associated to corrosion of metal reinforcing element. Ti-253 is a water based compound, effective on all types of steel used for armored reinforcement of concrete; it contains no nitrites, solvents, it does not create a vapor barrier and it is not flammable.

TECHNICAL CHARACTERISTICS: IDROTASS is a dual component product based on special hydraulic binders, selected aggregates with maximum granulometry of 0.6 mm and special additives in water dispersion; it is suitable to perform leveling operations that are waterproof, carbon dioxide and vapor proof; it has high deformability and priming qualities. IDROTASS is compliant to Italian Ministerial Decree 10/05/2004.

FIELD OF APPLICATION: Ti-253 is a liquid treatment to be applied by spray or brush to the exposed concrete surfaces or concrete surfaces detected by scarification before renovation, using TASSULLO TCA30/T thixotropic mortar or TASSULLO TCA-MI passivating thixotropic mortar with corrosion inhibitors, in order to extend the protective action to the adjacent zones of the plate block under reconstruction. If Ti-253 is applied on the concrete surface, it will migrate through the porous structure near the metal armor protecting it from corrosion. Ti-253 can increase the lifespan of the structures in reinforced concrete up to 70%.

FIELD OF APPLICATION: IDROTASS is used as a protective and waterproofing leveling product to be applied to surfaces, tanks, vertical and horizontal concrete slabs (waterproofing retaining walls and waterproofing before laying tiles), on sand and cement floor screeds, blocks or plasters based on hydraulic binders that require protection from water absorptions or water infiltrations.

ADVANTAGES: - high protection of reinforcing rods - easy to apply - it can be left exposed as a finishing HOW TO APPLY IT: Ti-253 must be applied by spray or brush to vertical or horizontal surfaces after having carefully washed and cleaned those areas in order to remove dust, oil, grease, release agents, old paints, etc. Low absorbent concrete must be treated with two coats applied 7 ÷ 8 hours after each other. Wash the treated surface through water jet before restoring using TASSULLO TCA3 / T, TCA MI, TP-551 on the dry surface. Ti-253 is compatible with all TASSULLO products for the restoration of reinforced concrete.

ADVANTAGES: - elastic - waterproof - de-icing salt resistant

- highly protective - easy and quick to apply

HOW TO APPLY IT: IDROTASS must be applied to clean surfaces using a metal spatula and in layers with a thickness of approx. 2 mm each. Any subsequent coat must be applied after the first application is cured (approx 12-24 hours). It is advisable to use reinforcing meshes in fiberglass with a weight greater than 150 g/m² at the presence of surfaces that show cracks caused by hydraulic shrinkage or that are subject to thermal deformation or static settling. MIXED PRODUCT YIELD: approx. 3 Kg/m²

ADHESION TO CONCRETE: 1 N/mm2

PACKAGE: IDROTASS/SACK powder in 24 kg sacks - IDROTASS/CAN liquid in 8 liter can

MIXING WATER: approx. 350 g/Kg YIELD: 4/5 m2/l PACKAGE: 1 or 5 liter can

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

resistant UV resistant

freeze - thaw cycling UNI EN 13687

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

BUILDINGS IN CONCRETE

BUILDINGS IN CONCRETE THERMAL INSULATION

PROTECTIVE AGENT

TP-551

PASSIVAT IN G G R O U T

TECHNICAL CHARACTERISTICS: TP-551 is a protective passivating powder to be used with the addition of water. It is free from solvents and nitrites. FIELD OF APPLICATION: TP-551 is used for protection of concrete reinforcement rods. TP-551 protects against steel armor rust and corrosion. ADVANTAGES: - easy to apply - solvent free HOW TO APPLY IT: TP-551 is mixed exclusively with water and it is applied by brush on the metal armor. MIXING WATER: approx. 350 g/Kg

POLYSTYRENE PLATE THERMAL INSULATION SYSTEM

ISI-THERM

TECHNICAL CHARACTERISTICS: ISI-THERM is a complete expanded polystyrene plate thermal insulation system with an ISI-FISS bonding agent and top coat plaster white or grey in color, featuring high adhesion and elasticity. It is an easy and cost effective product to improve home comfort. FIELD OF APPLICATION: ISI-THERM cladding system is recommended for a variety of surfaces, especially for concrete, brick and for old plastered surfaces. ADVANTAGES: - tested in reference to ETA-09/135 - immediate energy and financial savings - easy to apply - high insulating power THE SYSTEM COMES COMPLETE WITH ALL THE REQUIRED ACCESSORIES: bonding agent /top coat plaster ISI-FISS GR/Bn, insulated plates, AR160 fiberglass meshes, locking nails, colored finishing and accessories (corners bead, initial profiles, etc.).

YELD PER METER: approx. 50 g/m PACKAGE: in 1 or 5 Kg packages

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

ISI-FISS BONDING AGENT is COMPLIANT to

THERMAL INSULATION T HE R M AL IN S U LATI N G P LA S TE R

THERMAL INSULATION

TERMO-TASS

TECHNICAL CHARACTERISTICS: TERMO-TASS is a hydraulic binder-based thermal insulating fiberreinforced plaster combined with aggregates and selected lightweight minerals and polystyrene. It combines low thermal conductivity with ease of application and compatibility to a variety of masonry surfaces as well as high consistency and durability. TERMO-TASS is breathable and heat resistant, maintaining high average temperature within the wall and on the interior wall surface, improving energy savings and environmental comfort. TERMO-TASS is compliant to UNI EN 998-1 "Specifications for mortar for masonry – interior and exterior plaster mortars" and it is subject to CE marking in accordance to the regulations in force. FIELD OF APPLICATION: TERMO-TASS must be used to create machine processed breathable thermal insulated plasters for exteriors with a thickness greater than 2 cm on brick, stone, solid brick, concrete masonries, etc. ADVANTAGES: - highly insulating - suitable for any surface - breathable and resistant HOW TO APPLY IT: TERMO-TASS must be applied, also on uneven and discontinuous masonries, using a plastering machine for ready-to-use plaster and applied directly on the wall using a post screed. It is advisable to limit processing of material on the wall in order to avoid process off-cuts or excessive mix compacting. Thicknesses greater than 4 cm have to be achieved by applying several coats. MIXING WATER: approx. 0.85 l/Kg (approx. 10l/sack)

CONCRETE BUILDINGS

ETAG 004

MINERAL WOOL THERMAL INSULATION SYSTEM

RED SYSTEM

TECHNICAL CHARACTERISTICS: the RED SYSTEM is a complete thermal insulating system in slabs of mineral wool combined with ISI-FISS CALCE bonding top coat plaster featuring high adhesion and elasticity. The system’s full mineral structure offers many advantages by allowing a wide range of application, especially for areas where technical and legislative regulations require fireproof building materials. FIELD OF APPLICATION: the RED cladding system is recommended for all types of surfaces, especially those in concrete, brick, old plaster, and wood beams or load bearing walls. ADVANTAGES: - non-flammable - high sound absorption - breathable - sturdy and non deformable THERMAL CONDUCTIVITY OF THE BOARD T-RED: 0.036 W/(m x °K) THE SYSTEM COMES WITH ALL THE ACCESSORIES: ISI-FISS CALCE bonding / top coat plaster, insulating slabs, AR160 fiber glass mesh, locking nails, colored finishing and accessories (corners bead, initial profiles, etc.).

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

YIELD: approx. 3 Kg/(m² x cm) THERMAL CONDUCTIVITY (EN 12667): class T1 λ = 0,067 W/(m x °K) PACKAGE: 12 kg sack

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

ISI-FISS BONDING AGENT is COMPLIANT to

ETAG 004

PLEASE SEE DATA SHEET FOR A FULL OVERVIEW OF APPLICATION NOTES, METHOD OF USE AND APPLICATION WARNINGS

1 - CLADDING SYSTEMS

_Green SYSTEM _Red SYSTEM _WHITE SYSTEM _BROWN SYSTEM _ISI-THERM

ENERGY SAVING

2 - TOP COAT PLASTER FOR CLADDING SYSTEM _ISI-FISS/bn,gr _ISI-FISS MEDIO _ISI-FISS SOFT _ISI-FISS CALCE _ISI-FISS SOFT/CALCE _TK01/Ch

3 - THERMAL MORTARS AND PLASTERS

ENERGY SAVING

_T-MIM _T-192D _TERMO-TASS _TERMO-BI

Products and solutions for the thermal insulation requirements of any building

Thermal insulation for Tassullo is a synonym of interior comfort as well as a building’s breathability and naturalness. For this reason Tassullo has designed a range of THERMAL INSULATING MORTARS AND PLASTERS and the unique CLADDING SYSTEMS THAT ARE COMPLETELY BREATHABLE; a complete range of systems in which targeted natural bonding top coat plasters are used in combination with different panels, always guaranteeing the best performance: this is Tassullo’s extraordinary proposal.

www.isolamentocappotto.it 98

PRODUCT DATA SHEETS > 99

ENERGY SAVING

ENERGY SAVING THERMAL INSULATION

THERMAL INSULATION

GREEN/RED/WHITE/ BROWN/ISI-THERM

NATURAL CORK THERMAL INSULATION SYSTEM

l hydr

lic

nat

C L AD D ING TH E R M A L I N S U LATI O N SY S TE M

Proper insulation of a building is essential in order to respect the environment, save energy and ensure

lime

optimal comfort. Tassullo is a leader company in the production of sustainable materials in natural hydraulic

GREEN SYSTEM

TECHNICAL CHARACTERISTICS: the GREEN SYSTEM is a complete thermal insulating system in natural cork panels combined with TK01/Ch natural bonding and top coat plaster at high breathability. The system is characterized by high naturalness, surface resistance and good sound absorption. FIELD OF APPLICATION: GREEN SYSTEM is recommended to those who are seeking a comfortable climate by building in an ecological way and saving energy.

lime; it has developed a complete line of cladding systems capable of offering guaranteed naturalness, high thermal insulation and breathability.

ADVANTAGES: - insulating - ecological - resistant - high sound absorption.

Tassullo’s cladding thermal insulating systems, due to their use of natural materials, which are breathable and sustainable, improve human psycho-physical conditions at home, at the office, and generally indoors, where people spend most of their

PANEL SIZE: panel size (mm): 1000 x 500 thickness (mm): 20 – 30 – 40 – 50 – 60 – 70 – 80 – 100 - 120.

time. Tassullo’s cladding insulating systems represent for any building a living membrane, capable of protecting humanity, allowing the human body to breathe, to remain healthy indoors both in winter and summer.

THE SYSTEM IS EQUIPPED WITH ALL THE REQUIRED ACCESSORIES: TK01/Ch natural bonding / top coat plaster, insulating slabs, AR160 fiberglass mesh, locking nails, colored finishing and accessories (corners bead, initial profiles, etc.).

GUARANTEED THERMAL INSULATION Tassullo’s cladding systems serve the psycho-physical comfort of humanity

THERMAL INSULATION

Cladding insulating systems are not all the same. The choice of an insulating system respect to

MINERAL WOOL THERMAL INSULATION SYSTEM

another must not be limited only to economic

RED SYSTEM

considerations, but it should take into account, u

l hydr

lime

range of natural solutions capable of meeting the

WINTER INSULATION

needs of thermal insulation and environmental comfort. All thermal insulation systems come complete with all the necessary accessories for

SUMMER INSULATION

proper installation.

SYSTEM BREATHABILITY

TECHNICAL CHARACTERISTICS: the RED System is a complete thermal insulating system in slabs of mineral wool with ISI-FISS CALCE bonding top coat plaster with high adhesion and elasticity. The system’s structure, completely in mineral elements, offers many advantages by allowing its wide range of application, especially in areas where technical and legislative provisions require fireproof building materials. FIELD OF APPLICATION: the RED cladding system is recommended for all types of surfaces, especially those in concrete, brick, old plaster, and for wood beams or load bearing walls. ADVANTAGES: - non-flammable - high sound absorption - breathable - sturdy and non deformable PANEL SIZE: panel size (mm): 1000 x 600 thickness (mm): 30 – 40 – 50 – 60 – 80 – 100 - 120 - 140 - 160 - 180 - 200 THE SYSTEM IS EQUIPPED WITH ALL ACCESSORIES: ISI-FISS CALCE bonding / top coat plaster, insulating plates, AR160 fiber glass mesh, locking nails, colored finishing and accessories (corners bead, initial profiles, etc.).

Tassullo’s natural hydraulic limes guarantee breathability to the system Tassullo’s Research Center developed an exclusive range of bonding agents and top coat plasters for any type of cladding. The bonding agents created in NHL 5 Tassullo’s natural hydraulic lime ensure proper application in full respects of the system’s breathability, WATER VAPOR

wall

Cladding insulating systems

durability and naturalness, increasing the value of each individual components and improving quality of life and comfort. RED SYSTEM

www.isolamentocappotto.it Please see data sheet for a full overview of application notes, method of use and application warnings

100

101

ENERGY SAVING

For this reason, Tassullo developed a complete

lic

nat

above all, both comfort and quality of living.

ENERGY SAVING

ENERGY SAVING THERMAL INSULATION

THERMAL INSULATION

l hydr

lic

nat

CALC IU M SIL I CATE TH E R M A L I N S U LATIO N SYSTE M

lime

WHITE SYSTEM

TECHNICAL CHARACTERISTICS: the WHITE SYSTEM is a completely natural thermal insulating system in mineral slabs of calcium silicate combined with ISI FISS CALCE/Soft bonding top coat plaster. The system is completely mineral and has extraordinary thermal and acoustic qualities.

BONDING AGENTS – TOP COAT PL A S TERS FOR CL A DDING SYS TEMS

ISI-FISS/gr, bn

Bonding agent – top coat plaster for expanded polysterene plate

FIELD OF APPLICATION: the WHITE cladding system is recommended for application to brick surfaces or old plaster.

Bonding - top coat plaster; grey (ISI-FISS gr) or white (ISI-FISS bn) for plate thermal cladding. It is characterized by high

ADVANTAGES: - highly thermally insulating and fireproof - permeable to water vapor - highly resistant - easy to work with

adhesion and flexibility and it is recommended in combination with the expanded polystyrene slab (ISI-THERM SYSTEM). GRANULOMETRY: 0 - 0,5 mm

THE SYSTEM IS EQUIPPED WITH ALL REQUIRED ACCESSORIES: ISI-FISS CALCE/Soft bonding / top coat plaster, insulating plates, AR160 fiber glass mesh, locking nails, colored finishing and accessories (corners bead, initial profiles, ecc.). PANEL SIZE: panel size (mm): 500 x 500 thickness (mm): 75 – 100 - 125 - 150 - 175

BONDING YIELD: 3 - 5 Kg/mm2

PACKAGE: 25 Kg

ISI-FISS MEDIO

Bonding agent – top coat plaster and medium granulometry for eps plates

Bonding - top coat plaster in white color for plate thermal claddings, characterized by high adhesion and aggregates of a selected granulometry curve to enable quick application and easier leveling of the panel.

THERMAL INSULATION

lic lime

BROWN SYSTEM

TECHNICAL CHARACTERISTICS: The BROWN SYSTEM with a wood fiber panel, uses bonding top coat plasters NHL 5 certified in natural hydraulic lime which distinguish themselves for their exceptional qualities of: naturalness, breathability, healthiness. FIELD OF APPLICATION: the Brown cladding system is recommended for application both to masonry or wood structures, both to a frame or to a load bearing wall, and it is highly ecological featuring high breathability and excellent permeability; it is waterproof and it consists of: - T BROWN panel in wood fiber; - TK01/Ch bonding top coat plaster; - fiberglass rebar meshes; - TASSULLO colored mineral finishing. PANEL SIZE: panel size (mm): 1300 x 590 thickness (mm): 40 – 60 – 80 – 100

BONDING YIELD: 3 - 5 Kg/mm2

PACKAGE: 25 Kg

ISI-FISS SOFT

Bonding agent – light top coat plaster for plate cladding

Bonding - top coat plaster with high adhesion in white color for slag thermal claddings. It includes light perlitic aggregates. GRANULOMETRY: 0 - 1,4 mm

BONDING YIELD: 2 - 4 Kg/mm2

PACKAGE: 25 Kg

ISI-FISS CALCE

Bonding agent – high breathability top coat plaster in NHL5 lime

Bonding - top coat plaster in NHL5 natural hydraulic lime intentionally designed for bonding and leveling with high brea-

THE SYSTEM IS EQUIPPED WITH ALL REQUIRED ACCESSORIES: TK01/Ch natural bonding/top coat plaster, insulating plates, AR160 fiberglass mesh, locking nails, colored finishing and accessories (corners bead, initial profiles, etc.).

thability. Ideal in combination with slag in mineral wool (RED SYSTEM). GRANULOMETRY: 0 - 0,5 mm

BONDING YIELD: 3 - 5 Kg/mm2

PACKAGE: 25 Kg

ENERGY SAVING

l hydr

nat

WO O D FIB E R TH E R M A L I N S U LATI O N

GRANULOMETRY: 0 - 1,4 mm

THERMAL INSULATION PO LY ST E R E N E P LATE TH E R M A L I N S U L ATIO N SYSTE M

ISI-THERM

TECHNICAL CHARACTERISTICS: ISI-THERM is a complete expanded polystyrene plate thermal insulation system with an ISI-FISS bonding agent and top coat plaster white or grey in color, featuring high adhesion and elasticity. It is an easy and cost effective product to improve home comfort. FIELD OF APPLICATION: ISI-THERM cladding system is recommended for a variety of surfaces, especially for concrete, brick and for old plastered surfaces. ADVANTAGES: - tested in reference to ETA-09/135 - immediate energy and financial savings - easy to apply - high insulating power PANEL SIZE: panel size (mm): 1000 x 500 thickness (mm): 30 - 40 – 50 - 60 – 80 – 100 - 120 - 140 - 160 - 180 - 200 ISI-FISS BONDING AGENT IS COMPLIANT

ETAG 004

THE SYSTEM IS EQUIPPED WITH ALL REQUIRED ACCESSORIES: bonding agent /top coat plaster ISI-FISS, insulated plates, AR160 fiberglass meshes, locking nails, colored finishing and accessories (corners bead, initial profiles, etc.).

Please see data sheet for a full overview of application notes, method of use and application warnings

102

Bonding agent – high breathability light top coat plaster in NHL5 lime

ISI-FISS SOFT/CALCE

Bonding - top coat plaster in NHL5 natural hydraulic lime and lightweight aggregates (perlites) intentionally designed for bonding and leveling high breathability panels in calcium silicate (WHITE SYSTEM). GRANULOMETRY: 0 - 1,4 mm

BONDING YIELD: 2 - 4 Kg/mm2

PACKAGE: 25 Kg

TK01/Ch

Bonding agent – BIO-E NHL5 natural hydraulic lime top coat plaster

Bonding - top coat plaster in BIO-E NHL5 natural hydraulic lime intentionally designed for bonding and leveling natural and breathable panels. It is a natural product recommended for the GREEN and BROWN systems. GRANULOMETRY: 0 - 0,5 mm

BONDING YIELD: 3 - 5 Kg/mm2

PACKAGE: 25 Kg

Please see data sheet for a full overview of application notes, method of use and application warnings

103

ENERGY SAVING

ENERGY SAVING .

THERMAL INSULATION

T-MIM/ T-192D TERMO-TASS/TERMO-BI

T HE R M AL IN S U LATI O N SY S TE M S : T HE R M AL M O R TA R S A N D P LA S TE R S

THERMAL INSULATION THERMAL MORTARS A ND PL A S TERS

TH ERMA L MORTA R

T-MIM

TECHNICAL CHARACTERISTICS: T-MIM is an ideal bedding mortar for the installation of masonry blocks with low thermal loss coefficient. T-MIM is a thermal insulating bedding mortar with low specific weight, hydraulic binders-based and combined with lightweight aggregates and selected minerals and sands. T-MIM is compliant to UNI EN 998-2 "Specification for mortars for masonry. Masonry mortars.” and it is subject to CE marking.

Tassullo offers a full range of plasters and mortars capable of improving the thermal insulation of the masonry. Tassullo thermal plasters, thanks to their high insulating and breathable capacity, allow improving indoor comfort and

FIELD OF APPLICATION: T-MIM is particularly suitable for the construction of porous brick masonries where it is possible to avoid the presence of thermal bridges and to reduce the block’s theoretical insulation capacity.

energy performance of the building. They are suitable both for the restoration of masonries having discontinuous and irregular surfaces and for coating special decorative elements,

ADVANTAGES: - highly insulating - certified mechanical strength

curved surfaces, and no coplanar surfaces that are becoming more and more common in modern architectural structures.

HOW TO APPLY IT: T-MIM can be applied manually following the same method used for the application of traditional bedding mortar. It is advisable to apply TI-MIM to the surface in order to obtain a continuous flow of mortar.

The range of products includes a special thermo plaster in BIO-E NHL 5 natural hydraulic lime recommended for bio

MIXING WATER: 0,47 l/Kg (approx. 12 l/sack)

architecture applications.

Thermal conductivity (UNI 7745): λ = 0,22 W/(m x °K) PACKAGE: 25 kg sack and loose in silos equipped with mixing auger

thermal plasters technical data TERMO-TASS

TERMO-BI

λ=0,067

λ=0,091

fire behaviour thermal conductivity W (m °K) vapor permeability

μ=6

specific weight (Kg/mc)

270

μ=5 375

thermal mortar fire behaviour

T-MIM

T-192D

λ=0,22

thermal conductivity W (m °K) vapor permeability

λ=0,20

*M2,*M3,**M5

***CS II

1000

700

specific weight (Kg/mc)

THERMAL MORTARS A ND PL A S TERS

* according to Italian Ministerial Decree20/11/87 ** according to UNI EN 998-2 *** according to UNI EN 998-1

insulation systems technical data *

heat bridge correction systems technical data *

TERMO-TASS

TERMO-BI

equivalent vapor permeability

6,50

5,59

equivalent water layer thickness (m)

0,429

0,369

system

bioecology

the theoretical thermal insulation gain in comparison to the one of masonry built with traditional systems

T-MIM

T-192D

14%

24%

bioecology

* Data refer to systems consisting of a thermal plaster with a thickness of 6.00 mm, TAØ2 top coat plaster with a thickness of 3 mm and Tassullo mineral finishing

LEGEND:

system

= excellent

= good

* Data indicate theoretical gain in terms of thermal insulation guaranteed by the use of T-MIM as a bedding mortar for the construction of masonry having a thickness of 30 cm and with bricks having λ = 0.18 W /(m ° K) and using T = 192-D for infilling a line marking with a thickness of 10 cm instead of using a traditional mortar (λ = 0.9 W / (m K)

concrete

thermal brick

standard brick

old plaster

stone

wood blocks in cellular concrete

TERMO-BI

T-MIM

T-192D

= recommended

T-192D

TECHNICAL CHARACTERISTICS: T-192D is a thermal insulating mortar designed for filling and line marking repairs; it is particularly useful in buildings that are properly insulated to prevent the formation of thermal bridges. T192D is characterized by a thermal conductivity comparable to the one of porous bricks used in construction. T192D is compliant to UNI EN 998-1 and it is subject to CE marking in accordance to the regulations in force. T192D is compliant to the Italian Ministerial Decree 10/05/2004 and it is available in resistance class CSII in accordance to UNI EN 998-1 on plastering mortars. FIELD OF APPLICATION: T-192D is a thermally insulated mortar for filling and repairing line marking or holes. It is particularly suited in the construction of porous brick masonries whenever it is possible to avoid the presence of thermal bridges and to reduce the block’s theoretical insulation capacity caused by the filling of line markings using traditional plaster. ADVANTAGES: - highly insulating - high workability

MIXING WATER: approx. 2 l/sack of 10 kg YIELD: approx. 7 Kg/(m² x cm) Thermal conductivity (EN 1745:2002): λ = 0,2 W/(m x °K)

TERMO-TASS

LEGEND:

INFILLING THERMAL INS U L ATING MORTA R

HOW TO APPLY IT: T-192D can be applied manually following the same application methods used for traditional plastering mortar or it can be applied using a plastering machine for premixed plaster. The product plasticity and workability allow creating high thicknesses in just one coat (up to 10 cm).

Which insulating system on which masonry? system or thermal mortar

THERMAL INSULATION

ENERGY SAVING

plaster

thermal mortars technical data

PACKAGE: 18 kg sacks and loose in silos equipped with mixing auger

= suitable

Please see data sheet for a full overview of application notes, method of use and application warnings

104

105

ENERGY SAVING

THERMAL INSULATION T H E R M A L M O R TA R S AND P L AST E R S

TH ERM AL INSULATING P LASTE R

TERMO-TASS

TECHNICAL CHARACTERISTICS: TERMO-TASS is a hydraulic binder-based thermal insulated fiberreinforced plaster combined with aggregates and selected lightweight minerals and polystyrene. It combines low thermal conductivity with ease of application and compatibility to a variety of masonry surfaces as well as high consistency and durability. TERMO-TASS is breathable and heat resistant, maintaining high average temperature within the wall and on the interior wall surface, improving energy savings and environmental comfort. TERMO-TASS is compliant to UNI EN 998-1 "Specifications for mortar for masonry – interior and exterior plaster mortars" and it is subject to CE marking in accordance to the regulations in force. FIELD OF APPLICATION: TERMO-TASS must be used to create machine processed breathable thermal insulated plasters for exteriors with a thickness greater than 2 cm on brick, stone, solid brick, concrete masonries, etc. ADVANTAGES: - highly insulating - suitable for any surface - breathable and resistant HOW TO APPLY IT: TERMO-TASS must be applied, also on uneven and discontinuous masonries, using a plastering machine for ready-to-use plaster and applied directly on the wall using a post screed. It is advisable to limit processing of material on the wall in order to avoid process off-cuts or excessive mix compacting. Thicknesses greater than 4 cm have to be achieved by applying several coats. MIXING WATER: approx. 0.85 l/Kg (approx. 10 l/sack) YIELD: approx. 3 Kg/(m² x cm) THERMAL CONDUCTIVITY (EN 12667): class T1 λ = 0,067 W/(m x °K) PACKAGE: 12 kg sack

THERMAL INSULATION T H E R M A L M O R TA R S AND P L AST E R S

TH E RM AL INSULATING N ATURAL PLASTER

TERMO-BI

ENERGY SAVING

TECHNICAL CHARACTERISTICS: TERMO-BI is a thermal insulating, fiber-reinforced, natural plaster with low specific weight, in natural hydraulic lime BIO-E NHL 5 certified and selected perlites and expanded silicons. TERMO-BI combines excellent ease of applicability to its low thermal conductivity and excellent breathability. This plaster has the quality of being able to hinder heat exchange while maintaining a high average temperature within the wall and the interior wall surface, improving energy savings and environmental comfort. TERMO-BI is compliant to UNI EN 998-1 "Specifications for mortar for masonry - interior and exterior plaster mortars" and it is subject to CE marking in accordance to the regulations in force. FIELD OF APPLICATION: TERMO-BI must be used to create machine processed natural and breathable plasters for exteriors with a thickness greater than 2 cm for any type of surface. Thanks to its natural features and extremely low presence of water soluble salts TERMO-BI can be used also in the renovation of historical sites whenever thermal insulation is required. ADVANTAGES: - highly insulating - suitable for any surface - high consistency and durability over time - it contains BIO-E NHL 5 - a natural alternative to plate insulation - CE marking in accordance to the regulations in force HOW TO APPLY IT: TERMO-BI must be applied using a plastering machine for ready-to-use plaster and applied directly to the wall using a post screed. MIXING WATER: approx. 0.7 l/Kg (approx. 9 l/sack) YIELD: approx. 4 Kg/(m² x cm) THERMAL CONDUCTIVITY (EN 12667): class T1 - λ = 0,091 W/(m x °K) PACKAGE: 13 kg sack

Please see data sheet for a full overview of application notes, method of use and application warnings

106

107

WOOD HOUSEs

WOOD PRODUCTS

Garda Sporting Hotel - Riva del Garda (TN) - Italy Contracting Company: STP Ltd.

Specific products for the construction of wood houses

Tassullo chose to offer its natural and wood construction solutions with the goal of increasing both home comfort and energy saving.

LEED

108

Tassullo products for wood houses ensure healthy and livable environments and they maintain the warmth offered by wood; they are natural materials produced in full respect of the environment in order to increase the efficiency of wood houses: greater mass, higher energy efficiency, greater soundproofing and durability. PRODUCT DATA SHEET >

www.t-wood.it

109

WOOD HOUSES

wall system _T-Wood Rasante _T-Wood Intonaco _T-Wood Protettivo _T-Wood primer floor system _MASSETTO _PAVI/1 _T-48S/N _T-48S/B _T-LIVEL _T-FIX thermal insulation _BROWN SYSTEM

WALL SYSTEM (INTERIOR - EXTERIOR)

WALL SYSTEM (INTERIOR)

CLADDING SYSTEM (EXTERIOR)

top coat plaster / primer T-WOOD RASANTE

Interior finishing

top coat plaster T-WOOD RASANTE

mesh top coat plaster T-WOOD RASANTE

Tassullo colored finishing

fiberglass mesh

bonding agent / top coat plaster TK01/Ch

top coat plaster T-WOOD RASANTE plaster T-WOOD INTONACO

fiber glass mesh

drywall panels

cladding insulating system BROWN SYSTEM LEGNO

holding plaster mesh

WOOD FLOOR SYSTEM self-leveling top coat plaster T-LIVEL

wood floor

exterior surface

load bearing structure in wood

bearing structure in wood

Tassullo colored finishing

adhesion promoter T-WOOD PRIMER

WATER PROOFING SYSTEM

insulating panel in wood fiber T-BROWN LEGNO

thermal insulating mortar T-WOOD RIEMPIMENTO bearing structure in wood

waterproofing T-WOOD PROTETTIVO

REINFORCED CONCRETE SLAB SYSTEM

resin for wood floors

bonding T-FIX

tiles

waterproofing sheathing IDROTASS

MASSETTO TASSULLO

floor screed T48S/N

floor heating system

concrete bed

lightened floor screed PAVI/1

soundproofing sheathing

lightened floor screed PAVI/1

sheathing and vapor protection

floor heating system

WOOD HOUSES

wood floor

Wood houses Systems and applications 110

LEED

111

WOOD HOUSES

WOOD HOUSES WALL SYSTEM

WALL SYSTEM TO P C OAT P LA S TE R FO R O S B WO O D PA NE LS AND P LYWO O D

T-WOOD RASANTE

WATERPROOFING DUAL COMPONENT FOR WOOD S TRU CTU RE PROTECTION

TECHNICAL CHARACTERISTICS: T-WOOD RASANTE is a special top coat plaster in NHL 5 natural hydraulic lime specifically designed for leveling OSB wood panels and Plywood.

T-WOOD PROTETTIVO

TECHNICAL CHARACTERISTICS: T-WOOD PROTETTIVO is a dual component product in NHL 5 natural hydraulic lime, selected aggregates and special additives in water dispersion. In compliance to UNI EN 13986.

FIELD OF APPLICATION: T-WOOD RASANTE allows leveling any type of wood panels in compliance to EN 13986: OSB, Plywood, panels in wood particles bound with cement, and fiber panels.

FIELD OF APPLICATION: T-WOOD PROTETTIVO is designed for the application of protective leveling resistant to water, carbon dioxide and vapor, it has high deformability and adhesion to 3-4 OSB panels, Plywood, panels in wood particles bound with cement and fiber panels.

ADVANTAGES: - high elasticity - high adhesion - natural and breathable - cement and additives free

Examples of applications: - interior walls of bathroom or kitchen before tile installation(ref. OSB 3-4); - exteriors walls exposed to meteoric water; - exterior walls partially in contact with backfill.

HOW TO APPLY IT: T-WOOD RASANTE is applied to horizontal and vertical surfaces using a shaped trowel.

ADVANTAGES: - water and vapor protection - it is applied as a normal top coat plaster

MIXING WATER: 0,25 liters/Kg (approx. 6.5 liters/sack) YIELD: 3-4 Kg/m2

HOW TO APPLY IT: mix T-WOOD Protettivo /P (24 Kg sack) with T-WOOD/L (8 liters can) using a low rpm drill until the product is fully homogenized. It is applied to clean and dry panels using a metal spatula in layers that are approx.1.5/2 mm thick. It is advisable to use reinforcing fiber glass meshes with a weight greater than 150 g/m² embedded in the outer portion of the leveling layer.

ADHESION ON OSB PANEL: > 0,3 N/mm (ref. internal procedures and standard) PACKAGE: 25 kg sack

YIELD OF MIXED PRODUCT: 3 Kg/m2

lime

istan

lime

wa t er

l hydr

nat

lic

nat

PACKAGE: 24 kg sack + 8 liters can

ADHESION TO OSB PANEL: > 0,3 N/mm (ref. internal standards and procedures) al hydr

WALL SYSTEM

T-WOOD INTONACO

TECHNICAL CHARACTERISTICS: T-WOOD INTONACO is a NHL 5 certified natural hydraulic lime plaster; it is elastic and breathable, specifically designed for applications on holding plaster metal meshes. It is compliant to UNI EN 998-1 and subject to CE marking. FIELD OF APPLICATION: T-WOOD INTONACO is applied to holding plaster metal meshes mechanically and properly fastened to masonry and it is particularly suitable as interior plaster in light constructions (e.g. houses with load bearing structure in wood and lightweight insulating infilling) in order to increase the density of the masonry and consequently its thermal inertia. ADVANTAGES: - it increases masonry mass - high elasticity - high workability - cement and additives free

A DH ES ION PROMOTER FOR WOOD PA NEL S

T-WOOD PRIMER

TECHNICAL CHARACTERISTICS: T-WOOD Primer is a special acrylic emulsion in water, weather resistant, compatible with air and hydraulic binders typically used in construction (air lime, hydraulic lime, cement) and specifically suited for the preparation of fixative primers and adhesion promoters on wood panels. FIELD OF APPLICATION: T-WOOD Primer can be used as an adhesion promoter agent to be applied to panels in compliance to EN 13986 (OSB 3-4, Plywood, Particles in wood bound with cement, fiber Panels) in anticipation of subsequent leveling with T-WOOD RASANTE or T-WOOD PROTETTIVO. ADVANTAGES: - organic solvents free - improves priming and finishing

HOW TO APPLY IT: T-WOOD INTONACO is installed through continuous spray plastering machines fed by powdered product in compliance to the usual methods of application of the spray civil plasters. MIXING WATER: 0,21 liters/Kg (approx.6.5 liters/sack)

HOW TO APPLY IT: T-WOOD Primer can be spread on the OSB panel by roller or brush paying attention to spreading it evenly on the panel surface and preventing stagnation of emulsion in pores or gaps. YIELD: approx. 0.10 Kg/m²

WOOD HOUSES

NHL 5 NAT U R A L H Y DR A U LI C LI M E P LA STE R FO R WOOD CO N S TR U CTI O N S

PACKAGE: 5 liters can

YIELD: approx.15 Kg/(m² x cm)

l hydr u nat

nat

112

l hydr lic

lic

lime

See data sheet for a full overview of application notes, methods of use and application warnings.

PACKAGE: 25 kg sack or loose in silos

lime

See data sheet for a full overview of application notes, methods of use and application warnings.

113

WOOD HOUSES

WOOD HOUSES FLOORING SYSTEM

FLOORING SYSTEM FLO O R SC R E E DS

MASSETTO

R E A DY FLO O R SC RE E D

TECHNICAL CHARACTERISTICS: MASSETTO is a hydraulic binder based grout combined with selected aggregates; it is ideal to create floor screeds for civil use both for interiors and exteriors. MASSETTO is compliant to UNI EN 13813 "Floor screeds and materials for floor screeds -property and requirements," designed to be in compliance to EN 13813 CT-C25-F5 and subject to CE marking in accordance to the current legislation. MASSETTO is compliant to Italian Ministerial Decree 10/05/2004.

F LOOR S CREEDS

T48S/N

QU ICK DRYING F LOOR S CREED

FIELD OF APPLICATION: MASSETTO is a grout to be used for the installation of floor screeds for civil use with a thickness in the range of 4–12 cm. MASSETTO is suitable for floor heating systems and it is compatible for laying reinforcing electro welded meshes.

FIELD OF APPLICATION: T48S/N is a fiber-reinforced grout to be used for installation of quick drying floor screeds for civil use with a thickness in the range of 4–6 cm. T48S/N is suitable for floor heating systems and it is compatible with the installation of electro welded reinforced meshes.

ADVANTAGES: - it ensures quick installation - certified mechanical strength

ADVANTAGES: - suitable for floor heating systems - it allows creating quick drying mixes - certified mechanical strength

HOW TO APPLY IT: MASSETTO must be placed afar from the perimeter walls; it must be applied and leveled using a post and trowel according to standard methods of application of traditional sand and cement grouts for civil use floor screeds.

MIXING WATER: 3 liters/sack YIELD: approx. 20 Kg/(m²x cm)

MIXING WATER: 2 liters/sack

PACKAGE: 30 kg sack

YIELD: approx. 20 Kg/(m²x cm) IN CONFORMITY WITH UNI EN 13813

TESTED

CT-C25-F5

high mechanical resistance

FLOORING SYSTEM

PAVI/1

T H ERMALLY INSULATED LI G HTWE IG HT FLO O R SC RE E D

TECHNICAL CHARACTERISTICS: PAVI/1 is a lightweight, fiber-reinforced, polystyrene and hydraulic binder-based floor screed to be used as a thermally insulated base for filling between the floor and the floor screed pavement installation. PAVI/1 is compliant to Italian Ministerial Decree 10/05/2004. FIELD OF APPLICATION: PAVI/1 allows covering with ease the pipes of electric and hydraulic systems placed on the floor in order to obtain a flat surface on which to apply the floor screed installation. PAVI/1 provides high thermal insulation and it is sound-absorbent.

T48S/B

LOW TH ICKNESS F LOOR S CREED

ADVANTAGES: - sound absorbent and thermally insulating - lightweight - certified mechanical strength

PAVI/1

F LOOR S CREEDS

HOW TO APPLY IT: PAVI/1 must be applied directly above the floor and the pipes, with a thickness greater than 2–3 cm, making sure to meet the leveling requirements by using a rake, post or trowel.

ADVANTAGES: - high adhesion - certified mechanical strength HOW TO APPLY IT: T48S/B must be placed afar from the perimeter walls in layers with a thickness in the range of 2 and 4 cm, applied and leveled using a post and trowel according to standard methods of application of traditional sand and cement grouts for civil use floor screeds.

MIXING WATER: 7-10 liters/sack YIELD: approx. 3:4 Kg/(m²x cm)

WOOD HOUSES

FLOOR SC R E E DS

PACKAGE: 30 kg sack

MIXING WATER: 3 liters/sack

PACKAGE: 12 kg sack

YIELD: approx. 20 Kg/(m²x cm)

See data sheet for a full overview of application notes, methods of use and application warnings.

114

TESTED

certified mechanical strength

thermally insulating

sound absorbent

PACKAGE: 30 kg sack

IN CONFORMITY WITH UNI EN 13813

TESTED

ABILITY

CT-C25-F5-B0,5

high mechanical resistance

for irregular existing screeds

See data sheet for a full overview of application notes, methods of use and application warnings.

115

WOOD HOUSES

WOOD HOUSES THERMAL INSULATION

FLOORING SYSTEM SE L F-L E V E L I N G FIN ISHIN G COAT

T-LIVEL

S E L F-LE V E LING TO P COAT PLASTER

BROWN SYSTEM

WOOD FIBER THERMAL INSULATION SYSTEM

TECHNICAL CHARACTERISTICS: T-LIVEL is a high fluidity self-leveling finishing coat less than 2 mm thick, ideal for smoothing and finishing on traditional quick drying floor screeds.

TECHNICAL CHARACTERISTICS: the BROWN SYSTEM, with a wood fiber panel, uses bonding agents top coat plasters in NHL 5 certified natural hydraulic lime which distinguish themselves for their exceptional qualities: - naturalness; - breathability; - healthiness.

FIELD OF APPLICATION: T-LIVEL can be applied to traditional or quick drying interior floor screeds. It improves surface finishing avoiding roughness due to traditional floor screeds finishing defects.

FIELD OF APPLICATION: the cladding system named BROWN SYSTEM is recommended for application both to shaped frames or wall bearing wood structures; it is highly ecological, it has high breathability and excellent permeability, it is waterproof and it includes: - T-BROWN wood fiber panel; - TK01/Ch top coat plaster bonding; - fiber glass reinforcement mesh; - TASSULLO colored mineral finishing.

ADVANTAGES: - high resistance to abrasion - high adhesion - certified mechanical strength HOW TO APPLY IT: a thin layer of T-LIVEL must be spread on the existing floor screeds using a metal spatula. MIXING WATER: 7,5 liters/sack YIELD: approx. 2.5 Kg/m²

BOARD DIMENSION: panel size (mm): 1300 x 590 thickness (mm): 40 – 60 – 80 – 100

PACKAGE: 25 kg sack

l hydr

ABILITY

lic

nat

The system comes complete with all the required accessories: bonding/leveling, insulating plates, mesh and fiberglass , locking nails, colored finishing.

CERTIFICATE lime

high fluidity

high adhesion

INTERIOR WOOD FIBER INSULATING PANEL T-BROWN

FLOORING SYSTEM B O N D IN G ADH E S I V E

T-FIX

P R OFESSIONAL ADHESIVE FO R INTE RIO RS

WOOD BEARING STRUCTURE

TECHNICAL CHARACTERISTICS: T-FIX is a standard setting cement adhesive free from vertical sliding, suitable for horizontal and vertical interior bonding of ceramic tiles, stoneware, clinkers, and stone materials. It is classified under UNI EN 12004: Class C1T - cement adhesive (C), standard setting adhesive (1), and reduced sliding cement adhesive (T). FIELD OF APPLICATION: T-FIX is used as an adhesive for the installation of ceramic tiles (fired brick, single fired tiles, double fired tiles, clinkers, glazed porcelain, etc.) and stone material for wall or floor installation exclusively for interiors. ADVANTAGES: - no vertical sliding - high adhesion

MIXING WATER: 6,5 liters/sack

WOOD HOUSES

TASSULLO EXTERIOR FINISHING

YIELD: approx. 3-4 Kg/(m²x cm)

TK01/Ch BONDING /TOP COAT PLASTER

PACKAGE: 25 kg sack

FIBERGLASS MESH CERTIFICATE

CERTIFICATE

C1T EN 12004

See data sheet for a full overview of application notes, methods of use and application warnings.

116

no vertical sliding

CLADDING INSULATING SYSTEM BROWN SYSTEM

EXTERIOR

Brown system for cladding

See data sheet for a full overview of application notes, methods of use and application warnings.

117

ADVANCED SYSTEMS

_ Fireproofing Line _ IDROTASS _ T-FLASH

ADVANCED SYSTEMS

Tassullo Research Center waterproofed coating with IDROTASS.

PRODUCT DATA SHEET > 118

119

ADVANCED SYSTEM

Products and solutions for fireproofing, waterproofing and quick line marking repairs

All TASSULLO products are "special", innovative, and with performance specifically designed to address any issue, from fireproofing to waterproofing of all types of surfaces up to specific quick hardening products.

SPECIAL PRODUCTS

FIREPROOFING

FIREPROOFING TRF/AC-TRF/BA TRF/EL-TRF/MU-TRF /SA

FIREPRO OF IN G P RODU CT S

F IREPROOF BLOW ING PRODU CT

TRF/BA

TECHNICAL CHARACTERISTICS: TRF/BA is a blowing product for the creation of barriers and infilling against the spread of fire and for sealing firebreak elements. TRF/BA is a fully mineral and highly protective product.

Our products Thanks to an advanced technological research, Tassullo created

FIELD OF APPLICATION: TRF/BA can be applied to electrical crossing seals in cellular concrete firebreak walls; it is REI 180 certified by authorized laboratories of the Italian Ministry of the Interior. TRF/BA is used to seal structures in fire resistant masonries and to create passive barriers in case of fire.

a line of products capable of offering fireproofing certification to building structures (up to REI 180).

ADVANTAGES: - dimensionally stable - fully mineral - asbestos and solvents free - incombustible - not soluble in water

Fire retardant plasters, small blowing bags, passive protection barriers and protective components to prevent fire from spreading across the premises are all systems that Tassullo offers in order to make any type of structure safe.

HOW TO APPLY IT: TRF/AC is applied manually or with plastering machines for ready plaster and it can be finished with a post, spatula or metallic trowel. MIXING WATER: 0,55 liters/Kg (approx.11 liters/sack)

TRF/AC

TRF/BA

TRF/EL

TRF/MU

TRF/SA

VOLUMETRIC YIELD: 1,5 liters/per kg of powder FIRE CLASS: A1 PACKAGE: 30 Kg sack

Milan, Santa Monica neighborhood

Complete line of fireproofing products

FIREPROOFING

PASSIV E P R OTE CTI O N COATI N G FO R S T E E L STRUCTURE S

TRF/AC

TRF/EL

TECHNICAL CHARACTERISTICS: TRF/AC is a fireproof coating capable of providing passive fire protection to structural steel, ensuring structural stability for long exposure to fire.

TECHNICAL CHARACTERISTICS: TRF/EL is a blowing product for the creation of barriers against the spread of fire across cable ducts. TRF/EL is a fully mineral product.

FIELD OF APPLICATION: TRF/AC is applied as a protective coating against fire on steel structural elements (beams, pillars, etc.) In order to prolong the mechanical and structural stability characteristics at high temperatures.

FIELD OF APPLICATION: TRF/EL is applied to key points of the electrical system (cable crossings and branches) to create passive barriers in order to prevent the spread of fire caused by burning cables sheathing.

ADVANTAGES: - it is asbestos and solvents free - it does not produce toxic gas

ADVANTAGES: - asbestos and solvents free - it does not produce toxic gas - it improves the structure safety - dimensionally stable

HOW TO APPLY IT: TRF/AC is applied manually or using plastering machines for ready to use plaster and they can be finished using a post, spatula or metallic trowel, without applying any finishing in case of nonexposed surfaces or whenever not in contact with people or objects, otherwise finished with TASSULLO TA01/TA02 top coat plaster and subsequent finishing as per contract.

HOW TO APPLY IT: TRF/EL is applied manually or with an automatic water mixing and pumping system (plastering machines for ready plaster) and it can be finished using a spatula or metal trowel.

MIXING WATER: 0,8 liters/Kg (approx.16 liters/sack)

MIXING WATER: 0,85 liters/Kg (approx.17 liters/sack)

YIELD: approx. 4 Kg/(m² x cm)

FIRE CLASS: A1

PACKAGE: 20 Kg sack

See data sheet for a full overview of application notes, methods of use and application warnings.

120

F IREPROOF COATING FOR EL ECTRICA L DU CTS S EA L ING

See data sheet for a full overview of application notes, methods of use and application warnings.

121

ADVANCED SYSTEM

FIREPROOFING

SPECIAL PRODUCTS

FIREPROOFING FIREPROOF MASONRY PLASTER

TRF/MU

TECHNICAL CHARACTERISTICS: TRF/MU is a REI 120/180 certified plaster for brick partitions with a thickness of 8 cm, capable of offering a passive fire protection to masonries, floors and pillars ensuring dimensional stability, resistance to gas and fumes and thermal insulation for long fire exposure. FIELD OF APPLICATION: TRF/MU is applied as a fire protective coating to masonry structures, floors and pillars in order to prolong mechanical and thermal insulation characteristics for long exposure to fire. ADVANTAGES: - asbestos and solvents free - it does not produce toxic gas - it is REI 120/180 certified for brick partitions with a thickness of 8 cm - it improves the safety of the structures - dimensionally stable HOW TO APPLY IT: TRF/MU is applied manually or with an automatic water mixing and pumping system (plastering machines for ready plaster) and it can be finished using a spatula or metal trowel. MIXING WATER: 0,85 liters/Kg (approx.17 liters/sack) YIELD: approx. 4 Kg/(m² x cm) FIRE CLASS: A1 PACKAGE: 20 Kg sack

FIREPROOFING

TRF/SA

M O B IL E FIR E B A R R I E R

TECHNICAL CHARACTERISTICS: TRF/SA is a small blowing bag for the creation of barriers and infilling against the spread of fire and the sealing of firebreak elements. TRF/SA is a fully mineral product and it is incombustible. FIELD OF APPLICATION: TRF/SA is used to create mobile sealing on fireproof masonry structures and easily removable barriers that can be removed to avoid damage to the plant by blocking the spread of fire and acting as a passive protection in case of fire. TRF/SA allows creating in a very short time fireproofing structures that, if necessary, can be both temporary and reversible. ADVANTAGES: - quick installation - ideal under emergency conditions - asbestos and solvents free - it does not produce toxic gas - dimensionally stable HOW TO APPLY IT: place the small bags on top of each other according to the diagram illustrated in the data sheet. YIELD FOR REI 180 SEALING: approx. 150/m² for small bags sized 300 x 150 x 40 mm FIRE CLASS: A1

Kindergarten "Maria Amatori" Thiene (VI) - Italy See data sheet for a full overview of application notes, methods of use and application warnings.

122

123

ADVANCED SYSTEM

PACKAGE: 20 Kg sack

SPECIAL PRODUCTS

WATERPROOFING

IDROTASS

D U AL C O MP O N E N T WATE R P R O O F I N G LE V E LING

resistant UV resistant

WHAT IS IT? IDROTASS is a dual component product in special hydraulic binders and selected aggregates with maximum granulometry of 0.6 mm combined with special additives

freeze - thaw cycling

in water dispersion, suitable to create leveling that is

UNI EN 13687

waterproof, carbon dioxide and vapor proof, and that has high deformability and priming capacity. IDROTASS is compliant to Italian Ministerial Decree 10/05/2004.

HOW TO APPLY IT IDROTASS must be applied to surfaces that are clean and dust free, with no uneven elements, salts, greases, or organic materials; it is applied using a metal spatula and in layers approx.2 mm thick.

IDROTASS coating on the Tassullo Research Center

Any subsequent coat must be applied after the first application is cured (approx 12-24 hours). It is advisable to use reinforcing meshes in fiberglass with a weight greater than 150 g/mÂ˛ at the presence of surfaces with cracks caused by hydraulic shrinkage, subject to thermal deformation, or to static settling.

USE IDROTASS is used as a protective and waterproofing

sack Technical Data physical state

grey powder

specific weight

grey powder

granulometry

0,6 mm

powder specific weight

powder/liquid = 3 / 1

in Sack Tecnhical Data

approx.1450 Kg/mÂ˛

leveling product for surfaces, tanks, or vertical

(waterproofing of retaining walls) and horizontal

fire class

> 10,5 A1

(waterproofing prior to tile installation) concrete slabs; it is applied on sand and cement floor screeds, blocks or hydraulic binder based plasters that must

can Technical Data

be protected from the absorptions of water or from

physical state

whitish liquid

mixture ratio

powder/liquid = 3 / 1

other gases proof, as well as resistant to deicing salts

specific weight

approx. 1100 Kg/m3

and capable of increasing the lifespan of the support

being treated.

flammability

water infiltrations. IDROTASS creates a protective layer that is waterproof, vapor, carbon dioxide or

approx. 9 no

product Mix Technical Data physical state

plastic mortar

specific weight

approx. 1600 Kg/m2

IDROTASS (SACK) 24 Kg sack (powder) IDROTASS (CAN) 8 liter can (liquid)

approx. 3 Kg/m2 > 10,5

adhesion to cls

> 1 N/mm2

elastic modulus

500 N/mm2

IDROTASS application near to a construction joint

See data sheet for a full overview of application notes, methods of use and application warnings.

124

125

ADVANCED SYSTEM

yield

SPECIAL PRODUCTS

QUICK MORTAR T HE ONLY QU I CK M O R TA R FO R LI N E M ARKING RE PAIRS T HAT CAN B E I M M E DI ATE LY F I N I S H E D

Just after 30 minutes it is possible to apply the finishing T-FLASH is the only quick mortar that can be immediately finished; it has been designed to repair safely and quickly all electrical marking, hydraulic marking and holes without leaving any trace. T-FLASH is convenient to prepare by just adding water and, above all, it has been designed at the Tassullo Research and Development Laboratories to ensure quick drying. It allows applying the finishing just after 30 minutes from the application. In just 30 minutes T-FLASH allows filling and finishing electrical marking and hydraulic marking by avoiding shrinking of any marking and existing masonry. It allows creating significant thickness in one coat without casting (dripping). The packaging of T-FLASH in a sealed bag avoids soiling during the handling of the bag, especially when the work is performed inside residential homes and apartments.

technical data granulometry (UNI 1005-1) mixing water

advantages from 0 to 1mm approx. 4,5-5 liters/sack approx. 16 Kg/(m2 x cm)

yield

setting starting time setting end time at 20' fire class

approx. 1,3 Kg/meter line markings 20/40 mm 15/20 minutes A1

T-FLASH is the only quick mortar that can be immediately finished; it has been designed to repair safely and quickly all electrical marking, hydraulic marking and holes without leaving any trace. The quality of T-FLASH is guaranteed by its double seal: both sack and pallet are hermetically sealed.

quick drying

in comparison to traditional mortars it dries in approx. 20 minutes

immediately available for finishing

it allows immediate application of the finishing

high workability

it is a highly plastic product

high thicknesses

it allows creating high thicknesses

it is does not shrink

material does not shrink during maintenance

compatible with existing plasters

guarantees compatibility with existing plasters

clean sack

www.tflash.it See data sheet for a full overview of application notes, methods of use and application warnings.

126

127

ADVANCED SYSTEM

the sealed sack prevents soling during handling

TASSULLO RESEARCH CENTER CITRAC Architectural Competition award winning building for the years 2001 to 2008.

128

"Far from the logic of mimicry, Tassullo Research Center’s monolithic building in exposed concrete acquires an extraordinary iconic power in the landscape”

(Excerpt from Domus No. 929 dated 10-2009)

129

SOUTH ELEVATION

EAST ELEVATION

WEST ELEVATION

CROSS SECTION

LONGITUDINAL SECTION

TASSULLO RESEARCH CENTER CITRAC Architectural Competition award winning building for the years 2001 to 2008.

130

"Attention focused on actions that are proof of the search for a contemporary language respectful of the place." (Excerpt from Domus No. 929 dated 10-2009)

131

ALPHABETICAL INDEX OF PRODUCTS

BIO-E NHL5

p.82

T-BLOCK

p.43

T30V

p.72

TLTX

p.40

Bio-e/FINITURA

p.85

T-cream

p.39

T30V/Fibro

p.72

TP-551

p.96

BIO-E/FONDO

p.86

T-Fix

BIO-E/P

p.84

BIO-E/P1

p.54, 116

T48S/B

p.53, 115

TRF-AC

p.120

T-Fix Flex

p.55

T48S/N

p.53, 115

TRF-BA

p.121

p.84

T-Fix HP

p.55

T501

p.37

TRF-EL

p.121

BIO-E/P2

p.83

T-Fix IE

p.54

T50S

p.39

TRF-MU

p.122

BIO-E/RASANTE

p.85

T-FLASH

p.44, 126

T5FB

p.40

TRF-SA

p.122

BIO-E/RC

p.83

T-FLASH/FR

p.95

T600-00

p.48

TRG/03

p.48

BIO-E/SOFT

p.86

T-FLASH Restauro

p.69

T600-01

p.49

WHITE SYSTEM

BROWN SYSTEM p.102, 117

T-GREEN

p.88

TADP/C

p.87

Fenix NHL 3,5 Chiara

p.67

T-LIVEL

TAØ2

p.58

Fenix NHL5

p.66

T-MIM

p.105

TAØØ/TAØ1/TAØ2/TAØ4

p.73

Fenix-B

p.68

T-MULTI / sf, sg

p.45

TBØØ/TBØ1/TBØ2/TBØ4

Finiture Tassullo Grassello GREEN SYSTEM IDROTASS

p.49, 58

T-SPAN

p.37, 46

p.47, 67, 82

T-Stone

p.101 p.95, 124

p.46, 74

TBL

p.69

p.77

TC-Paint

p.94

T-WOOD INTONACO

p.112

TCA-MI

p.93

T-WOOD PRIMER

p.113

TCA1

p.93

ISI-FISS CALCE

p.103

T-WOOD PROTETTIVO

p.113

TCA3/C

p.92

ISI-FISS MEDIO

p.103

T-WOOD RASANTE

p.112

TCA3/T

p.92

ISI-FISS SOFT

p.103

T170-P

p.41

TERMO-BI

p.77, 87, 106

ISI-FISS SOFT/CALCE

p.103

T170-PS

p.41

TERMO-TASS

p.56, 96, 106

p.59, 103

T200

p.36

TF01/TF02/TF04

p.74

ISI-THERM

p.60, 97, 102

T20V

p.70

TF1000

p.47

MASSETTO

p.52, 114

T20V color

p.70

TFS1

p.75

MIXTO PAVI

p.50

T25V

p.71

Ti-253

p.94

MIXTO PAVI B

p.50

T270-P

p.42

TK01/Ch

MIXTO PAVI R

p.51

T270-PS

p.43

TK01/gr, bn

p.59

ISI-FISS/gr,bn

132

p.56, 116

p.102

p.88, 103

PAVI/1

p.52, 114

T300

p.36

TL84

p.38

RED SYSTEM

p.97, 101

T30rc

p.68

TL97

p.38

T-192 D

p.45, 105

T30S

p.73, 75

TLast-100

p.76

133

134

135

V1/P.03-2011

Dealer

Establishments Tassullo - Via Nazionale 157 (TN) - Italy Mollaro di Taio - Via alla Miniera 1 (TN) - Italy Solferino - Via Napoleone III 110 (MN) - Italy Ozzano Monferrato - Via Rivara 5 (AL) - Italy Bucarest - Bolintin Deal - Romania RESEARCH CENTER Tassullo - Via Nazionale 157 (TN) - Italy

Tassullo Materiali S.p.A.

T. +39.0463.662100 - F. +39.0463.662138 - www.tassullo.com