Adhesives

Adhesive

Code Description GLU001 Kwik Tak Spray Adhesive Can Suitable for sticking seams before stitching Size (ml) 500

Code Description GLU002 Kayobond General Purpose Aerosol Adhesive Suitable for foam bonding. Not suitable for bonding to external skin of boat. Use GLU005 Size (ml) Coverage (m2) 500 6 - 8

Code Description GLU003 Kayobond High Heat Adhesive GLU004 Kayobond High Heat Adhesive Suitable for bonding side lining carpets and laminates. Not suitable for PVC, foam backed vinyl and vinyls. Size (l) Coverage (m2) 1 2.5 - 3

5 12.5 - 15

Code Description Size (ml) Coverage (m2)

GLU005 Kayobond Web Tack High Heat Adhesive 500

Suitable for bonding foam backed vinyl fabrics to outer skin of boat. Not suitable for unbacked vinyl and PVC. Can also be used for sidelining. 6 - 8

Code Description GLU011 Kayobond PVC Adhesive GLU006 Kayobond PVC Adhesive GLU007 Kayobond PVC Adhesive Suitable for most unbacked vinyl and PVC Size (l) Coverage (m2) 250ml 0.6 - 0.75

1 2.5 - 3

5 12.5 - 15

Code Description Size (l) Coverage (m2)

GLU008 Kayobond PSA Water Based Adhesive

5 This water based adhesive is suitable for soft, delicate fabrics and foam backed vinyls. It may be used in enclosed areas. 8 - 10

Code Description GLU900 Adhesive Spatula 4”

Code Description GLU009 Kayobond PVC 1 litre and Curing Agent 60g GLU010 Kayobond PVC 5 litre and Curing Agent 300g Size (l) Coverage (m2) 1 2.5 - 3

5

Can be added to Kayobond PVC to improve heat and water resistance. For external use only. Curing agent must be added to entire tin, this is a one use adhesive, cannot be stored once mixed.

Code Description GLU901 Solvent 1 Cleaner Used to prepare and clean surfaces Size (l) 1

Adhesive Useful Tips

Preparation

Take off covering. Remove any powdered foam using cleaning wheel. Clean surface with solvent cleaner – GLU901. Once process is complete see general application.

General Application Contact Adhesive

Apply even coat to both surfaces using spreader. Ensure adhesive is fully touch dry. Bring surfaces together. Ensure no air between surfaces. Once surfaces are laid, apply even pressure all over using a hard block or roller.

All surfaces need to be dry and dust free.

DO NOT use adhesive in temperature less than 10 degrees centigrade.

Aerosol Spray Adhesive

Surface preparation as described previously. Apply evenly from left to right a coat of adhesive spray to one side, on the second substrate apply an even coat top to bottom. Leave adhesive to dry 4-5 minutes or until tacky to touch. Bring surfaces together. Ensure no air between the surfaces. Apply even pressure using block or roller.

Water Based Pressure Sensitive Adhesive

Surface preparation as before. Apply even coat using paint roller to solid surface wood or fibreglass. Leave to completely dry, adhesive will look clear and tacky to touch. Once dry apply fabric. Fabric may be repositioned to final dressing.

Damp or damaged surfaces should be replaced.

Ensure all areas are well ventilated when applying solvent based products.

Do not use near naked flames.

Health and Safety

For full health and safety guidelines refer to the material data sheets available from Kayospruce Ltd or at www.kayospruce.com

For further details regarding applications refer to the technical data sheet.

Please Note:

Prior to use, ALWAYS test the adhesive onto sample material. The adhesives that we sell are regularly in use and well proven in the textile industry. However, we cannot be held responsible for damage to your materials if the adhesive system does not work. It is your responsibility to choose the correct product for your requirement. Because of the nature of the adhesives they cannot be shipped by Sea or Airfreight. Some road transport within the UK may be restricted too. Consult with Kayospruce when ordering.