Rev 2:3
106E
LAND ROVER DISCOVERY 3 2005LAND ROVER DISCOVERY 4 AUGUST 2009RANGE ROVER SPORT 2005RANGE ROVER SPORT I 2005-2009RANGE ROVER SPORT II 2009(L320, 9A & CA Models) e11*94/20*7744*00
Powder Coated Finish
Components Code
Quantity
Bolt Kit
Description
Code
Quantity
w1622
Description
DP
1
Drop Plate
WA
8
12mm Large Round Washers
HP
1
Hook Plate
F
2
16x50 Set Screws, Nuts & Grip Washers
LS
1
Left Strap
C
2
16x40 Set Screws, Nuts & Grip Washers
RS
1
Right Strap
E
2
12x40 Set Screws, Nuts & Grip Washers
MB
1
Main Body
B
2
12x45 Set Screws, Nuts & Grip Washers
SMB
1
Socket Mounting Bracket
D
2
12x130 Bolts, Nuts & Grip Washers
A
2
10x30 Set Screws, Nuts & Grip Washers
BU
2
Bushes 11m x Diameter
BS
2
Bushes 88mm x 25 Diameter
SW
2
12mm Small Square Washers (25x30x6)
G
2
5x20 Set Screws, Round Washers & Grip Washers
SC12
2
12mm Set Screw Head Covers
SC16
4
16mm Set Screw Head Covers
1.
Remove red plastic cover from the cross member - lower the spare wheel.
2.
Insert main body MB into the tapered housing on the rear cross member and hold in position. Slide hook plate HP up between the main body MB and the tapered housing and insert into the existing slotted hole in the rear cross member. Loosely attach hook plate HP to main body using set screw A. Loosely attatch main body MB to rear cross member using set screws B, Bushes BU and washers SW.
3.
Loosely attach drop plate DP to main body MB using set screws C.
4.
Pre 2008 models - Remove the two existing M14 bolts from inner face of chassis rails (note:- retaining nut on outer face is securing chassis bush and is not holding M14 bolt) loosely attach straps LS and RS to existing M14 bolts.
5.
Models 2008 onwards - Insert bushes BS into the holes in chassis and loosely attach straps LS & RS using bolts D with washers WA.
6.
Loosely attach straps LS & RS to drop plate DP using set screws E with washers WA.
7.
Attach towball A50/1 (Not Supplied) with a D value exceeding 17kn using set screws F.
8.
Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing. Then replace spare wheel.
NOTE:- This kit also comes with an extra socket plate for 12s electrics so it can be attached using fixings G to the existing electric socket mounting point inside the rear crossmember.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:6
106E
LAND ROVER DISCOVERY 3 2005LAND ROVER DISCOVERY 4 AUGUST 2009RANGE ROVER SPORT 2005RANGE ROVER SPORT I 2005-2009RANGE ROVER SPORT II 2009(L320, 9A & CA Models) e11*94/20*7744*00
Powder Coated Finish
Components Code
Quantity
Bolt Kit
Description
Code
Quantity
w1622
Description
DP
1
Drop Plate
WA
8
12mm Large Round Washers
HP
1
Hook Plate
F
2
16x50 Set Screws, Nuts & Grip Washers
LS
1
Left Strap
C
2
16x40 Set Screws, Nuts & Grip Washers
RS
1
Right Strap
E
2
12x40 Set Screws, Nuts & Grip Washers
MB
1
Main Body
B
2
12x45 Set Screws, Nuts & Grip Washers
SMB
1
Socket Mounting Bracket
D
2
12x130 Bolts, Nuts & Grip Washers
A
2
10x30 Set Screws, Nuts & Grip Washers
BU
2
Bushes 11mm x 19 Diameter
BS
2
Bushes 88mm x 25 Diameter
SW
2
12mm Small Square Washers (25x30x6)
G
2
5x20 Set Screws, Round Washers & Grip Washers
SC12
2
12mm Set Screw Head Covers
SC16
4
16mm Set Screw Head Covers
1.
Remove red plastic cover from the cross member - lower the spare wheel.
2.
Insert main body MB into the tapered housing on the rear cross member and hold in position. Slide hook plate HP up between the main body MB and the tapered housing and insert into the existing slotted hole in the rear cross member. Loosely attach hook plate HP to main body using set screw A. Loosely attach main body MB to rear cross member using set screws B, Bushes BU and washers SW.
3.
Loosely attach drop plate DP to main body MB using set screws C.
4.
Pre 2008 models - Remove the two existing M14 bolts from inner face of chassis rails (note:- retaining nut on outer face is securing chassis bush and is not holding M14 bolt) loosely attach straps LS and RS to existing M14 bolts.
5.
Models 2008 onwards - Insert bushes BS into the holes in chassis and loosely attach straps LS & RS using bolts D with washers WA.
6.
Loosely attach straps LS & RS to drop plate DP using set screws E with washers WA.
7.
Attach towball A50/1 (Not Supplied) with a D value exceeding 17kn using set screws F.
8.
Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing. Then replace spare wheel.
NOTE:- This kit also comes with an extra socket plate for 12s electrics so it can be attached using fixings G to the existing electric socket mounting point inside the rear crossmember.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com