Rev 2:1
112E 112ED
CITROEN C3 HATCHBACK CITROEN DS3
Powder Coated Finish
e11*94/20*9584*00
w436
Components
Mainframe
Description
Bolt Kit
Code
Quantity
Code
Quantity
Description
CB
1
Crossbar
WA
4
10mm Large Round Washer
SP
2
Side Plate
B
4
10x30 Set Screws & Grip Washers
C
4
12x35 Set Screws, Nuts & Grip Washers
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1.
Remove two fixings securing the lower edge of the bumper to the vehicle body. Remove the plastic fixings securing the wheel arch liners to the bumper. On the DS3 model cut the bumper as shown in the diagram overleaf. Pull wheel arch liners away from the chassis rails to provide access to the mounting points. Remove the tape covering the threaded holes on the outside rear edges of the chassis rails.
2.
Loosely attach side plates SP to the outside of each chassis rail using set screws B with washers WA.
3.
Loosely attach crossbar CB to side plates SP using set screws C. Note: It may be necessary to lower the exhaust for better access.
4.
Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
5.
Re-attach bumper and wheel arch liners using original fixings.
Detachable Neck: Attach to crossbar CB using set screws Z. Flange Neck: Attach to crossbar CB using bolts A then attach type approved towball a50/1 (not supplied) using set screws G. 6.
Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
112E 112ED
Powder Coated Finish
CITROEN C3 HATCHBACK CITROEN DS3
Bolt Torque Settings Bolt Size (mm)
Pitch (mm)
Torque Setting (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
112E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description
Flange Neck
Code
Quantity
A G
2 2
w493
Description
12x100 Bolts,Nuts & Grip Washers 16x50 Set Screws, Nuts & Grip Washers
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com