Rev 2:2
113E 113ED
RANGE ROVER EVOQUE 2011-
Powder Coated Finish
e11*94/20*9562*00
w672
Components
Mainframe
Code
Quantity
CB
1
LA
1
Description
Bolt Kit Code
Quantity
Crossbar
B
2
14x90 Bolts & Grip Washers
Left Angle
WA
2
14mm Large Round Washers
RA
1
Right Angle
TS
1
T-Strap
RB
1
Right Bracket
Description
C
6
12x35 Set Screws, Grip Washers & 3 Nuts
WB
3
12mm Small Round Washers
E
1
12x40 Set Screw, Grip Washer & Nut
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Remove the steel exhaust surrounds from the face of the bumper (4 fixings). Remove the exhaust surrounds plastic support brackets (2 fixings). Note: Use lubricant and gently pull rearwards. 2. Lower exhaust from its rubber mountings and remove the heat shield from inside the bumper. Remove bumper: 3 fixings inside each wheel arch, fold back arch liners and remove torx screws inside wheel arch. Remove light clusters, (2 fixings each side under small cover), Remove plastic bungs on each corner of boot shut panel, 4 fixings on lower edge, 4 torx screws up inside bumper to heat shield. Pull bumper rearwards away from body clips and disconnect wiring loom. Cut off both ends of the heat shield to allow re-fitment. Cut out a section centrally from the bottom edge of the shield 80mm deep x 100mm wide. 3. Clean out all threaded points. Loosely attach left angle LA using bolt B with washer WA in the forward most hole only. Remove the two 8mm nuts from the left hand side rear panel X and loosely attach strap TS using the two original nuts. Loosely attach strap TS to angle LA using bolt B and washer WA. 4. Loosely attach right angle RA using set screws C with washers WB. 5. Loosely attach crossbar CB to angles LA & RA using set screw C. Remove 8mm nut from bottom left original fixing on right hand side, Loosely attach right bracket RB to the original fixing X using original nut and attach to crossbar CB using bolt E. 6. Refit bumper, all panels and exhaust. 7. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing. Detachable Neck: Attach using set screws Z. Flange Neck: Attach using bolts A and type approved towball.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:2
113E 113ED
Powder Coated Finish
RANGE ROVER EVOQUE
Bolt Torque Settings Bolt Size (mm)
Pitch (mm)
Torque Setting (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
113E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description Flange Neck
Code
Quantity
A
2
12x100 Bolts, Nuts & Grip Washers
G
2
16x50 Set Screws, Nuts & Grip Washers
w493
Description
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com