Rev 2:1
115E 115ED
Powder Coated Finish
NISSAN JUKE 2WD (Exc 4x4) e11*94/20*8334*00
w648
Components Code Mainframe
Quantity
Description
Bolt Kit Code
Quantity
Description
CB
1
Crossbar
WC
4
12mm Small Round Washers
LA
1
Left Arm
WB
4
12mm Large Round Washers
RA
1
Right Arm
WA
4
10mm Large Round Washers
AN
2
Angle
NT
4
10mm Nuts & Grip Washers
CP
2
Captive Plate
B
4
12x40 Set Screws & Grip Washers
C
4
12x40 Set Screws, Grip Washers & 2 Nuts
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1.
Remove Bumper — 2 bolts either side on boot closure panel, 2 plastic fixings in both wheel arches. Remove wheel arch liner to expose and remove hidden screws. Disconnect fog lamp. Pull bumper rearwards to remove.
2.
Remove impact beam and foam impact protector. Re-fit original impact beam bolts. Remove plastic trim from lower valance.
3.
Insert captive plates CP inside both chassis rails and locate through the holes in the bottom face of each rail. Loosely attach angles AN to the captive plates CP on the outside of the chassis using nuts NT with washers WA.
4.
Insert arm LA in left chassis rail and arm RA in right chassis rail. Loosely attach LA and RA to the chassis and screws B with washers WB.
angles using set
5. Loosely attach crossbar CB to arms LA and RA using set screws C with washers WC. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing. 6. Cut lower plastic trim as shown and re-fit to vehicle. Detachable Neck: Attach to crossbar CB using set screws Z. Flange Neck: Attach to crossbar CB using bolts A. Then attach type approved towball (not supplied) using set screws G. 7. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing. 7.
Re-fit bumper. Reconnect fog light.
8.
Note — When not towing the towbar neck should be removed to prevent it from obscuring the fog light.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:4
115E 115ES 115ED
NISSAN JUKE 2WD (Exc 4x4)
Powder Coated Finish
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch (mm)
Torque Setting (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
115E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description Flange Neck
Code
Quantity
A
2
12x100 Bolts, Nuts & Grip Washers
G
2
16x50 Set Screws, Nuts & Grip Washers
w493
Description
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com