Rev 2:1
99E/122E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description
Flange Neck
Code
Quantity
A G
2 2
w493
Description
12x100 Bolts, Nuts & Grip Washers 16x50 Set Screws, Nuts & Grip Washers
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
99E/122E 99E/122ED
BMW 1 SERIES (F20) (F21) 2006-2011 BMW 3 SERIES SALOON (F30) ESTATE (F31) BMW 4 SERIES (F32) COUPE 2013BMW 4 SERIES (F33) CONVERTIBLE 2013BMW 4 SERIES (F36) GRAND COUPE 2014(Exc Active Hybrid Models)
Powder Coated Finish
e11*94/20*9757*00 Components
Mainframe
Code
Quantity
Description
CB
1
Crossbar
BSS
1
Bumper Support Saloon
BSE
1
Bumper Support Estate
w
Bolt Kit Code
Quantity 1
Description Fitting Instruction
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. 2.
Remove plastic trim surrounds from the rear light clusters. Remove fixings from light clusters 1 each side. Pull light cluster rearwards to remove. Bumper Removal: 1 Series — 6 fixings on lower edge of bumper. 4 fixings around each wheel arch. Peel back wheel arch liner and remove bumper tip screw fixings. Pull rearwards unclipping from plastic body panel. Disconnect reversing sensors and any secured wiring. 3 Series — Remove fixings from underside of bumper, 2 fixings in each wheel arch. Peel back wheel arch liner and remove bumper tip screw fixings. Pull bumper rearward unclipping from retaining clips. Disconnect reversing sensors and any secured wiring.
3. 3 Series— Cut undertray or heat shield as shown in diagram. 4.
Remove impact beam. Retain fixings for re use when securing crossbar. Hand beam to customer.
5.
Mount crossbar CB on the original studs, secure and fully tighten using original fixings.
6.
Refit bumper, using bumper supports BSS or BSE, reversing sensors and any disconnected wiring. Refit lights and wheel arch liners.
Detachable Neck: Attach to crossbar CB using set screws Z. Flange Neck: Attach to crossbar CB using bolts A. 7. Attach type approved towball (not supplied) using set screws G. 8. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
99E/122E 99E/122E
Powder Coated Finish
BMW 1 SERIES (F20) (F21) 2006-2011 BMW 3 SERIES SALOON (F30) ESTATE (F31) BMW 4 SERIES (F32) COUPE 2013BMW 4 SERIES (F33) CONVERTIBLE 2013BMW 4 SERIES (F36) GRAND COUPE 2014(Exc Active Hybrid Models)
Bolt Torque Settings Bolt Size (mm)
Pitch (mm)
Torque Setting (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com