Rev 2:1
123E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description Flange Neck
Code
Quantity
A
2
12x100 Bolts, Nuts & Grip Washers
G
2
16x50 Set Screws, Nuts & Grip Washers
w493
Description
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
123E 123ED 123ES
Powder Coated Finish
RENAULT GRAND SCENIC 2009e11*94/20*8308*00 w467
Components
Mainframe
Description
Bolt Kit
Code
Quantity
Code
Quantity
CB
1
Crossbar
WA
4
10mm Large Round Washers
Description
LS
1
Long Strap
WB
4
12mm Small Round Washers
SS
1
Short Strap
E
4
10x40 Set Screws & Grip Washers
B
4
12x40 Set Screws, Grip Washers & 2 Nuts
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Remove light clusters (2 fixings & 1 thumbscrew behind each cluster inside boot). 2. Remove bumper— 2 fixings under light clusters, 2 fixings in each wheel arch and 1 fixing behind wheel arch liner (loosen to gain access), 4 fixings on top edge and 6 on the bottom edge. Pull bumper tips outwards and gently pull the bumper rearwards whilst taking care not to put any strain on the wiring looms. Disconnect the wiring at the plugs. 3. Remove the boot floor covering, spare wheel, side panels, rear panel and the tape covering the 4 mounting points inside the boot. 4. Remove the impact beam. (Keep with the vehicle for refitting if the towbar is removed). Remove silver foil pads. (Re-use these for resealing the ends of the chassis rails to prevent water ingress). Remove metal tab obstructing access to the left hand chassis rail. Remove air vent and any plastic bungs from the left hand rear panel. 5. Insert straps LS and SS into the chassis rails and loosely attach to the 4 mounting points inside the boot using set screws E and washers WA. 6. Loosely attach crossbar CB to straps LS and SS using set screws B and washers WB. Tighten and check all fasteners 7. Refit all boot panels, spare wheel and boot floor covering. It is recommended that the ends of the chassis rails are sealed to prevent water ingress (sealant not provided) and refit the bumper remembering to reconnect the wiring loom. Detachable Neck: Atttach to crossbar CB using set screws Z. Swan Neck: Attach to crossbar CB using CPE10 plates (standard orientation) with set screws Y & bolts W Flange Neck: Attach to crossbar CB using bolts A. Attach type approved towball (not supplied) using fasteners G. 8. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
123E 123ED 123ES
Powder Coated Finish
RENAULT GRAND SCENIC
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com