Rev 2:1
130E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description Flange Neck
Code
Quantity
A
2
12x100 Bolts, Nuts & Grip Washers
G
2
16x50 Set Screws, Nuts & Grip Washers
w493
Description
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
130E 130ED 130ES
CHEVROLET CAPTIVA
Powder Coated Finish
e11*94/20*8114* 01
w862
Components
Mainframe
Code
Quantity
Description
CB
1
Crossbar
SR
1
Right Side Plate
SL
1
BT
2
Bolt Kit Code
Quantity
Description
WA
8
12mm Large Round Washers
E
2
12x40 Bolts, Nuts & Grip Washers
Left Side Plate
B
4
12x40 Bolts & Grip Washers
Bumper Tabs
C
6
12x60 Bolts & Grip Washers
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Remove rear bumper :- 4 fixings on lower edge, 1 screw in lower corner, 3 screws in each wheel arch, 6 fixings on top edge and 1 fixing under each light cluster—remove lights to gain access. 2. Remove and discard impact beam and rear towing eye. 3. Loosely attach side arms SL and SR to the pre-threaded point on inside faces of each chassis using fasteners C with washers WA. Loosely position bumper tabs BT to lower fixing points on side plates SL and SR using fasteners B and washers WA. 4. Loosely attach crossbar CB to side plates SL and SR using fasteners B and E. 5. Cut bumper as shown in diagram and replace. Detachable Neck: Attach detachable neck D to crossbar CB using set screws Z. Swan Neck: Attach swan neck SN to crossbar CB with IP plates using fasteners A. Flange Neck: Attach flange neck F to crossbar CB using bolts A. Attach type approved towball ( not supplied ) using set screws G. 6. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
130E 130ED 130ES
Powder Coated Finish
CHEVROLET CAPTIVA
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com