Rev 2:1
131E
Including Stratum Powder Coat Finish
FLANGE NECK
Components Code
Quantity
F
1
Bolt Kit
Description
Flange Neck
Code
Quantity
A G
2 2
w493
Description
12x100 Bolts, Nuts & Grip Washers 16x50 Set Screws, Nuts & Grip Washers
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
131E 131ED 131ES
Powder Coated Finish
BMW 5 SERIES SALOON (F10) March 2010& TOURER ESTATE (F11) September 2010(Inc M-Sport & GT Models) e11*94/20*8402*00 w
Components
Mainframe
Code
Quantity
CB
1
Description
Bolt Kit Code
Crossbar
Quantity
Description Original Fixings
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Remove mud flaps if fitted— wheel arch screws either side. 2. Remove bumper— release plastic clips on lower edges of bumper. Remove fixings in wheel arches. Remove trim covers below light clusters by gently lifting the top edge first and unclip. (Caution the clips break easily) . Remove fixings which were under the trim. Remove under tray— plastic fixings on lower edge of bumper and 2 bolts on the wheel well. Unclip the sides of the bumper starting at the tips by pulling sideways away from the vehicle. With both sides free pull the bumper rearwards which will disconnect the remaining clips on the back panel. Disconnect the reversing sensors and place bumper in a safe place. 3. Remove impact beam— 2 nuts either side (retain for re-use). Disconnect the exhaust rubber from the beam. Retain beam for refitting. 4. Loosely mount crossbar CB on the impact beam mounting studs. Remount impact beam over crossbar and fully secure using original nuts. Refit exhaust rubber to impact beam. 5. Refit bumper ensuring sensors are reconnected. Care must be taken to ensure the bumper locates correctly in the clips on the back panel otherwise damage may occur when the boot is closed. Refit light trim covers. 6. Depending on customer preference, the under tray can either be cut to original marked area or removed and retained for future re-fitting. Detachable Neck: Atttach to crossbar CB using set screws Z. Swan Neck: Attach to crossbar CB using CPE10 plates (standard orientation) with set screws Y & bolts W Flange Neck: Attach to crossbar CB using bolts A then attach type approved towball (not supplied) using fasteners G. 8. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:2
131E 131ED 131ES
Powder Coated Finish
BMW 5 SERIES SALOON (F10) March 2010& TOURER ESTATE (F11) September 2010(Inc M-Sport & GT Models)
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com