Rev 2:4
134ED 134ES 134E
MERCEDES E Class Saloon (W212) 2009-2016 MERCEDES E Class Estate (S212) 2010-2016 (Inc Facelift 2013-) MERCEDES CLS Shooting Brake (X218) (Detachable Only) 2012-
Powder Coated Finish
E 11 55R-019763 w979
Components Code Mainframe
Quantity
Description
CB
1
Crossbar
ST
2
Straps
Bolt Kit Code
Quantity
Description
WA
20
10mm Large Round Washers
B
12
10x40 Set Screws , Grip Washers & 8 Nuts
C
2
12x35 Set Screws, Nuts & Grip Washers
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Remove boot floor covering, rear trim panel, side panels and floor supports. Remove light clusters (three nuts either side). 2. Remove bumper, three fixings in each arch and one tip screw securing bumper to wheel arch, four fixings on lower edge, two fixings through rear panel (this may require a special tool due to a long threaded stud). Pull bumper tips outwards and unclip bumper from rear plastic support. Disconnect reverse sensors. 3. Remove side heat shields and dismount the exhaust. Remove bumper impact beam and return to customer. 4. With the foam gaskets still in place - cut a slit, then insert straps ST inside the chassis. Remove the grommets from the chassis rails inside the boot and loosely attach straps ST using set screws B and washers WA. 5. Slide crossbar CB over the straps ST and loosely attach crossbar CB to the rear panel using set screws B and washers WA. Attach straps ST to the crossbar CB using set screws C. Tighten all fixings. 6. Re-attach bumper and all fixings, trim and reverse sensors. Detachable Neck: Attach to crossbar CB using set screws Z. Swan Neck: Attach to crossbar CB with CPE10 plates ( standard orientation ) using set screws Y & bolts W. Flange Neck: Attach to crossbar CB using set screws A. Attach type approved towball using set screws G. 7. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:4
134ED 134ES 134E
Powder Coated Finish
MERCEDES E Class Saloon (W212) 2009-2016 MERCEDES E Class Estate (S212) 2010-2016 (Inc Facelift 2013-) MERCEDES CLS Shooting Brake (X218) (Detachable Only) 2012-
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch (mm)
Torque Setting (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com