Rev 2:1
144E 144ED
NISSAN Qashqai (Inc +2) 2008-2013 (J10 2007-2013, J11 2014-)
Powder Coated Finish
e11 55R—0110352
w765
Components
Mainframe
Code
Quantity
Description
CB
1
Crossbar
Bolt Kit Code
Quantity
Description
WC
2
12mm Large Round Washers
LA
1
Left Angle
WA
4
12 Small Round Washers
RP
1
Right Angle
WB
5
10mm Small Round Washers
CA
1
Captive Angle
C
1
10x35 Set Screws, Nuts & Grip Washers
CN
1
Captive Nut Strap
E
4
12x35 Set Screws & Grip Washers
SC
1
Single Captive Bolt Plate
B
6
12x35 Set Screws, Nuts & Grip Washers
RA
1
Right Angle
NT
1
10mm Nut & Grip Washers
F
2
10x40 Set Screws & Grip Washers
BC12
4
12mm Bolt Covers
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1.
Remove bumper. Remove fixings along bottom edge, fixings around wheel arch, one tip screw and pull wheel arch outer trim to reveal push in clips on rear panel. Disconnect reversing sensors (where fitted) and fog lamps.
2. Remove chassis end caps. Insert captive angle CA inside the left chassis (this may need trimming slightly) and loosely attach left angle LA using set screws E and B with washers WA. 3. Loosely attach captive angle to left chassis using set screws E and B with washers WA and WC. 4. Insert single captive bolt plate SC inside the right chassis and loosely attach right plate RP using nut NT washers WB and set screws C with washers WB. 5. Loosely attach right angle RA to plate RP using set screws B. 6. Insert captive nut plate CN and loosely attach right angle RA to chassis using sets F with washers WB. (Check diagram for details). 7.
Loosely attach crossbar CB to left angle LA and to right plate RP using set screws E and B.
Detachable Neck: Attach using set screws Z. Flange Neck: Attach using set screws A and type approved towball (not supplied) using set screws G . 8. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:5
144ED 144ES
Powder Coated Finish
NISSAN Qashqai (Inc +2) (J10 & J11)
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch (mm)
Torque Setting (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
144E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description
Flange Neck
Code
Quantity
A G
2 2
w493
Description
12x100 Bolts, Nuts & Grip Washers 16x50 Set Screws, Nuts & Grip Washers
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com