Rev 2:1
148E
VAUXHALL CORSA ‘D’ 2006-2014 ‘E’ 2014- &CORSA VAN (Exc VXR & models with built in cycle carrier) ALFA MITO HATCHBACK 2010– FIAT GRANDE PUNTO 2006-2012 FIAT PUNTO VAN 2009-
Powder Coated Finish
e11*94/20*7278*00
Components Code
Quantity
CB
1
Crossbar
CS
1
LA
1
RA SP
Bolt Kit
Description
Code
Quantity
WA
14
10mm Large Round Washers
Centre Strut
D
2
16x50 Set Screws, Nuts & Grip Washers
Left Angle
A
4
10x35 Set Screws & Grip Washers
1
Right Angle
B
4
10x35 Set Screws, Nuts & Grip Washers
1
Spacer Plate
NT
2
10mm Nuts & Grip Washers
C
2
12x90 Bolts, Nuts & Grip Washers
w1063
Description
1. Remove rear bumper (2 screws in each wheel arch, 2 on bottom edge, 2 behind number plate). Pull out tips of bumper to release clips on top edges— removal of the light clusters will assist in disconnecting from the clips. 2. Remove and discard impact beam . 3. Insert angles LA and RA into each chassis rail and loosely attach to forward mounting points using set screws A with washers WA. 4. Offer up crossbar CB to the rear panel and loosely attach using nuts NT and washers WA. (For ALFA MITO drill holes as in diagram 11mm.) Attach crossbar CB to angles LA and RA using set screws A and washers WA. Attach crossbar to Remaining fixing points using set screws B and washers WA. Tighten set screws B and nuts NT followed by set screw A on the crossbar and then set screw A on the forward chassis point. 5. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings specified on the towbar drawing. 6. Cut rear bottom centre edge of bumper as per diagram. 7. Refit bumper 8. Attach centre strut CS to crossbar CB using set screws C. Attach type approve towball (not supplied) using set screws D. Note— on certain bumper types it will be necessary to fit spacer plate SP to prevent set screws C from damaging the bumper. 9. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
148E
Powder Coated Finish
VAUXHALL CORSA ‘D’ & ‘E’ & CORSA VAN (Exc VXR & models with built in cycle carrier) ALFA MITO HATCHBACK FIAT GRANDE PUNTO FIAT PUNTO VAN
Bolt Torque Settings Bolt Size (mm)
Pitch (mm)
Torque Setting (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com