Rev 2:1
175E 175ED 175ES
Powder Coated Finish
AUDI A4 SALOON (B8/8K) & AVANT ESTATE (B8/8K) e11*94/20*8122*00 w652
Components Code Mainframe
Quantity
Bolt Kit
Description
Code
Quantity
Description
CB
1
Crossbar
WA
6
10mm Large Round Washers
LA
1
Left Angle
B
2
12x40 Set Screws & Grip Washers
RA
1
Right Angle
C
2
12x40 Set Screws, Nuts & Grip Washers
E
4
10x100 Bolts, Grip Washers & 2 Nuts
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Remove rear bumper. Remove boot floor covering and side storage compartments. Remove light clusters. Remove fixings under light clusters. Remove rear plastic panel and grommets to reveal one nut each side. Remove luggage strap retainers. Remove fixings along lower edge of bumper and inside wheel arches remove and discard rear impact beam, two bolts each side of boot floor. 2. Insert angles LA & RA inside the chassis rails and loosely secure using fasteners E with washers WA. (To gain access to forward left bolt, lower exhaust and heat shield. These are covered with tape from above). 3. Loosely attach crossbar CB to angles LA and RA using fasteners B and C. Tighten all fasteners, replace exhaust and rear bumper. Cut bumper as shown in diagram. 4. Re– fit sensor to mounting plate using original fixings on crossbar. Detachable Neck: Attach to crossbar CB using fasteners Z. Swan Neck: Attach swan neck SN to crossbar CB using fasteners A. Flange Neck: Attach to crossbar CB using bolts A. 5. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
175E 175ED 175ES
Powder Coated
AUDI A4 Saloon and Estate 2008AUDI A5 2007
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
175E
FLANGE NECK
Powder coated
Components Code
Quantity
F
1
Bolt Kit
Description
Flange Neck
Code
Quantity
A G
2 2
w493
Description
12x100 Bolts,Nuts & Grip Washers 16x50 Set Screws, Nuts & Grip Washers
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com