Rev 2:1
183E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description Flange Neck
Code
Quantity
A
2
12x100 Bolts, Nuts & Grip Washers
G
2
16x50 Set Screws, Nuts & Grip Washers
w493
Description
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
183E 183ED 183ES
Powder Coated Finish
RENAULT SCENIC 2009e11*94/20*8290*00
w532
Components
Mainframe
Code
Quantity
CB
1
LS
1
RS
1
Description
Bolt Kit Code
Quantity
Description
Crossbar
WA
2
10mm Large Round Washers
Left Strap
WB
6
12mm Large Round Washers
Right Strap
C
2
10x35 Bolts & Grip Washers
B
6
12x40 Bolts, Grip Washers & 2 Nuts
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Remove rear light clusters ( 2 torx screws on boot closing panel and 1 screw inside each rear side panel) Note: undo screw half way and push outward for easier removal of cluster. Remove bumper ( 1 fixing on top edge of bumper in each light cluster area, 4 fixings on top edge, 2 fixings inside wheel arches also 1 small torx screw, 1 fixing behind arch liner with 5 fixings on lower edge), pull out bumper tips and remove bumper. Disconnect wiring loom for fog lamps and reversing sensors. 2. Remove impact beam. Remove foiled seals from rear panel to gain access to chassis rails. Remove metal tag from left chassis opening. Remove tape from mounting points inside the boot area, Note: the mounting hole is hidden on the opposite side on the left chassis rail, remove air vent on outside to gain access. On the left chassis remove the bolt securing the exhaust hanger bracket. 3. Insert straps LS and RS inside the chassis rails and loosely secure the most forward mountings using bolts C and washers WA. 4. Insert mainframe CB inside the chassis rails alongside straps LS and RS. Loosely attach using bolts B and washers WB. Tighten all bolts using a calibrated torque tool to settings specified on the towbar drawing. 5. Trim foiled seals and re attach. (It is recommended to use sealant to seal, this may prevent possible water damage). 6. Re fit bumper. (The central bumper tag will need a slight trim). Re attach exhaust hanger and lights. Detachable Neck: Attach to crossbar CB using set screws Z. Swan Neck: Attach to crossbar CB with CPE10 plates ( standard orientation ) using set screws Y & bolts W. Flange Neck: Attach to crossbar CB using set screws A. Attach type approved towball using set screws G. 7. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT All A1 Stratum towbars are finished with our unique powder coat.
A1 Towbars Limited, Parkway Link, Kettlebridge Road, Sheffield, S9 3AJ T: 0800 404 7070 E: technicalsupport@a1towbars.com
www.a1towbars.com
Rev 2:1
183E 183ED 183ES
RENAULT SCENIC
Powder Coated Finish
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com