Rev 2:1
191E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description Flange Neck
Code
Quantity
A
2
12x100 Bolts, Nuts & Grip Washers
G
2
16x50 Set Screws, Nuts & Grip Washers
w493
Description
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:6
191E 191ES 191ED
PEUGEOT 3008 2009 — December 2016 Excludes models fitted with AdBlue tank
Powder Coated Finish
e11*94/20*9559*00 w556
Components Code Mainframe
Quantity
Description
CB
1
Crossbar
LA
1
Left Angle
RA
1
Bolt Kit Code
Quantity
WA
8
8mm Large Round Washers
B
4
8x50 Set Screws, Nuts & Grip Washers
WB
4
10mm Large Round Washers
NT
4
C
4
BU
1
Right Angle
Description
10mm Nuts & Grip Washers 12x35 Set Screws, Nuts & Grip Washers Bush 7mmx19mm Diameter
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Remove the 3 fixings bolts from the impact beam. Disconnect the 3 bumper tags from the lower panel and lower rearmost exhaust hanger. 2. Insert set screws B with washers WA into the lower rear panel. (Thread the bolts so they only just protrude through the nuts). The nearside bolt and captivated nut is missing— insert set screw B with washer WA on the outside of the panel and bush BU on the inside of the panel as a substitute for the missing nut. 3. Position angles LA and RA over the studs on the chassis rails and loosely secure using nuts NT with washers WB. Thread set screws B fully in and tighten. Loosely add 8mm nuts provided with set screws B and washers WA. 4. Loosely attach crossbar CB to angles using set screws C. Tighten all fixings. Refit exhaust hanger and bumper tags. Detachable Neck: Attach to crossbar CB using set screws Z. Swan Neck: Attach to crossbar CB with CPE10 plates ( standard orientation ) using set screws Y & bolts W. Flange Neck: Attach to crossbar CB using set screws A. Attach type approved towball using set screws G. 5. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
191E 191ED 191ES
PEUGEOT 3008
Powder Coated Finish
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com