Rev 2:1
204E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description
Flange Neck
Code
Quantity
A G
2 2
w493
Description
12x100 Bolts, Nuts & Grip Washers 16x50 Set Screws, Nuts & Grip Washers
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
204E 204ED 204ES
Powder Coated Finish
DACIA LOGAN MCV ESTATE
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:2
204E 204ED 204ES
Powder Coated Finish
DACIA LOGAN MCV ESTATE E11 55R-0110164 w834
Components
Mainframe
Code
Quantity
CB
1
Crossbar
Description
LP
1
RP
1
Bolt Kit Code
Quantity
WA
8
10mm Large Round Washers
Description
Left Plate
B
4
10x90 Bolts, Nuts & Grip Washers
Right Plate
C
4
12x40 Set Screws, Grip Washers & 2 Nuts
BU
4
52x19mm Diameter
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Lower exhaust and heat shield to gain access to chassis rails. 2. Remove tape covering the four mounting points on the inside face of each chassis, remove the plastic grommets from the outside of the chassis. 3. Loosely attach plates LP & RP to the inside of the chassis rails using bolts B with washers WA, placing bushes BU through the chassis. 4. Loosely attach crossbar CB to the side plates LP & RP using set screws C. Detachable Neck: Attach to crossbar CB using set screws Z. Swan Neck: Attach to crossbar CB with CPE10 plates (standard orientation) using set screws Y & bolts W. Flange Neck: Attach to crossbar CB using bolts A. Attach type approved towball (not supplied) using set screws G. 5. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing. 6. Replace exhaust and heat shield.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com