Rev 2:1
209E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description
Flange Neck
Code
Quantity
A G
2 2
w493
Description
12x100 Bolts, Nuts & Grip Washers 16x50 Set Screws, Nuts & Grip Washers
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
209E 209ED 209ES
Powder Coated Finish
DACIA SANDERO STEPWAY 2013E11 55R-0110167 w834
Components Code Mainframe
Quantity
Description
Bolt Kit Code
Quantity
Description
CB
1
Crossbar
WA
8
10mm Large Round Washers
LP
1
Left Plate
B
4
10x90 Bolts, Nuts & Grip Washers
RP
1
Right Plate
C
4
12x40 Set Screws, Grip Washers & 2 Nuts
BU
4
52x19mm Diameter Bushes
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1.
Lower spare wheel (where fitted).
2.
Remove lights, 2 screws holding rear light clusters, pull clusters rearwards and disconnect.
3.
Remove bumper, 1 fixing under each light cluster bracket, 4 torx screws on top edge of bumper, 2 screws in each wheel arch, 2 bolts each side behind reflectors, (do not remove reflectors).1 screw each side on lower corners and 1 bolt securing bumper to wheel arch. Disconnect reverse sensors and number plate wiring. Lower exhaust and heat shield to improve access to chassis.
4.
Remove tape and plastic grommets covering holes on outer face of chassis and mastic from mating surfaces.
5.
Loosely attach side plates LP & RP to the inside of the chassis rails using bolts B with washers WA inserting bushes BU from outer face.
6.
Loosely attach crossbar CB to side plates LP & RP using set screws C.
7.
Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
8.
Cut bumper as shown in diagram.
9.
Replace bumper, heat shield & exhaust.
Detachable Neck: Attach to crossbar CB using set screws Z. Swan Neck: Attach to crossbar CB with CPE10 plates (reverse orientation) using set screws Y and bolts W. Flange Neck: Attach to crossbar CB using bolts A. Attach type approved towball (not supplied) using set screws G. 10. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
209E 209ED 209ES
Powder Coated Finish
DACIA SANDERO STEPWAY 2013-
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com