Rev 2:11
216E 216ES 216ED
VOLKSWAGEN GOLF 6 & Plus & 7 Hatchback & SV VOLKSWAGEN GOLF Cabriolet AUDI A3 Hatchback 3 Door (2009-2013) AUDI A3 Hatchback 3 and 5 Door (2013– Dec 2016) AUDI A3 S LINE (Swan & Detachable Only) SEAT LEON E11 55R-0110304
Powder Coated Finish
w339
Components Code Mainframe
Quantity
Description
Bolt Kit Code
Quantity
Description
CB
1
Crossbar
WA
2
12mm Large Round Washers
SA
2
Side Arms
WB
4
10mm Large Round Washers
C
4
10x40 Set Screws & Grip Washers
B
2
12x40 Set Screws & Grip Washers
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. GOLF: Remove bumper. Remove lights. Remove fixings inside boot. Remove screws in wheel arches, screws on lower edges, 1 screw on each corner tip. Pull bumper rear-ward off plastic clips, disconnect any wiring. A3: Remove lights, plastic peg from top outer corners of bumper, remove panel inside boot, remove 4 grommets on inside rear panel revealing 4 nuts and remove these using a long socket, remove screws inside wheel arches and lower edge of bumper, pull bumper off plastic clips, disconnect any wiring. LEON: Remove lights. Remove screws from beneath light clusters. Remove screws from lower edge and inside wheel arches, 1 tip screw either side. Pull bumper off plastic clips and disconnect any wiring. ALL MODELS: Remove impact beam, replace bolts to prevent ingress of water. 2. On SEAT LEON cut a slot from the lower plastic valance behind bumper 50mm deep x 100mm wide. 3. Locate fixing points on outer faces of each chassis rail, remove any tape or mastic. 4. Insert side arms SA inside the chassis rails and loosely attach using set screws C with washers WB. (AUDI A3 SPORTSBACK— USE SETTING 1, FOR OTHERS USE SETTING 2). 5. Insert crossbar CB inside the chassis rails and loosely attach using set screws C and B with washers WB and WA. Tighten all fixings. 6. S-LINE MODELS ONLY: Cut lower edge of bumper as per diagram. 7. Replace bumper and lights. Detachable Neck: Atttach to crossbar CB using set screws Z. Swan Neck: Attach to crossbar CB with IP plates using bolts A. Flange Neck: Attach to crossbar CB using bolts A. Attach type approved towball (not supplied) using fasteners G.
8. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:11
216E 216ES 216ED
VOLKSWAGEN GOLF 6 & Plus & 7 Hatchback & SV VOLKSWAGEN GOLF Cabriolet AUDI A3 Hatchback 3 Door (2009-2013) AUDI A3 Hatchback 3 and 5 Door (2013– Dec 2016) AUDI A3 S LINE (Swan & Detachable Only) SEAT LEON
Powder Coated Finish
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch (mm)
Torque Setting (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com