Rev 2:9
221ED 221E
Powder Coated Finish
CITROEN C4 PICASSO (B78) & C4 GRAND PICASSO 2013– PEUGEOT 308 HATCHBACK & SW (ESTATE) 2014-
w546
Components Code
Quantity
Code
Quantity
CB
1
Crossbar
WA
6
8mm Large Round Washers
Mainframe
Description
Bolt Kit Description
SP
2
Side plates
WB
4
10mm Large Round Washers
LP
1
Left Plate
B
6
8x40 Set Screws & Grip Washers
RP
1
Right Plate
C
4
12x50 Set Screws, Grip Washers & 2 Nuts
NT
4
10mm Nuts & Grip Washers
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Remove Bumper, CITROEN PICASSO: 2 fixings in each wheel arch, 9 fixings on lower edge, 1 tip bolt either side, pull white plastic slides towards wheel arch to release bumper tips. Pull bumper off clips and disconnect wiring looms on left hand side. Remove 2 other bolts each side of impact beam. PEUGEOT 308: Remove rear boot panel and side panels inside boot, remove lights, remove fixings inside each wheel arch, remove 1 tip bolt each side, 9 fixings on lower edge. Pull bumper off clips and disconnect wiring loom. Remove 3 outer bolts either side of the impact beam. 2. ALL VEHICLES: Loosely attach crossbar CB to the rear impact beam using set screws and washers WA. 3. Remove any mastic from the sides of each chassis rail. 4. Loosely attach side plate SP to the mounting studs on each chassis rail using nuts NT with washers WB. 5. Loosely attach side arms SP to crossbar CB using set screws C. 6. PEUGEOT 308 ONLY: Loosely attach mounting plates RP and LP to the rear panel using set screws B and washers WA. 7. Attach mounting plates RP and LP to crossbar CB using set screws C. 8. Tighten all fixings with a calibrated torque tool to specified torque settings on the towbar drawing. 9. Remove the pre marked area inside the bumper. 10. Re-fit bumper
Detachable Neck: Attach detachable neck D using set screws Z. Flange Neck: Attach flange neck F using bolts A & type approved towball (not supplied) using set screws G. 13. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:9
221ED 221E
Powder Coated Finish
CITROEN C4 PICASSO (B78) & C4 GRAND PICASSO 2013PEUGEOT 308 HATCHBACK & SW (ESTATE) 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch (mm)
Torque Setting (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com