Rev 2:1
237E 237ED
KIA SORENTO HYUNDAI SANTA FE
Powder Coated Finish
E11 55R-0110511
w1381
Components
Mainframe
Description
Bolt Kit
Code
Quantity
Code
Quantity
Description
CB
1
Crossbar
WA
8
12mm Large Round Washers
LA
1
Left Angle
WB
4
10mm Large Round Washers
RA
1
Right Angle
WC
6
12mm Small Round Washers
LC
1
Left Cleat
B
4
12x120 Bolts, Nuts & Grip Washers
RC
1
Right Cleat
C
4
10x1.25x40 Set Screws & Grip Washers
E
2
12x35 Set Screws, Nuts & Grip Washers
H
4
12x40 Set Screws, Nuts & Grip Washers
I
2
12x40 Set Screws & Grip Washers
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Lower spare wheel—remove (cut or break off) two dowels where the ends of the chassis meet the rear valance. 2. Cut off the centre bumper tag. Cut bumper to bumper cut detail (Detachable Only). 3. Loosely attach angles LA and RA to each chassis rail using bolts B and washers WA. 4. Loosely attach cleats LC and RC to the threaded holes in each chassis rail using set screws C with washers WB. 5. Attach cleats LC and RC to the angles LA and RA using set screws E. 6. Attach crossbar CB to angles LA and RA using set screws H & I with washers WC. Detachable Neck: Attach to crossbar CB using set screws Z. Flange Neck: Attach to crossbar CB using bolts A then attach type approved towball (not supplied) using set screws G. 7. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing. 8. Replace spare wheel. (This may fit a little further forward than before).
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
237E 237ED
Powder Coated Finish
KIA SORENTO (November 2012-) HYUNDAI SANTA FE (September 2012-)
Bolt Torque Settings Bolt Size (mm)
Pitch (mm)
Torque Setting (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
237E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description
Flange Neck
Code
Quantity
A G
2 2
w493
Description
12x100 Bolts, Nuts & Grip Washers 16x50 Set Screws, Nuts & Grip Washers
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com