Rev 2:1
258E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description Flange Neck
Code
Quantity
A
2
12x100 Bolts, Nuts & Grip Washers
G
2
16x50 Set Screws, Nuts & Grip Washers
w493
Description
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
258E 258ED 258ES
Powder Coated Finish
FORD FOCUS III ESTATE e11*94/20*9628*00
w420
Components
Mainframe
Code
Quantity
Description
Bolt Kit Code
Quantity
Description
CB
1
Crossbar
WA
4
10mm Large Round Washers
LSP
1
Left Side Plate
WB
4
12mm Small Round Washers
RSP
1
Right Side Plate
B
4
12x40 Set Screws, Nuts & Grip Washers
CS
2
Captive Strap
NT
4
10mm Nuts & Grip Washers
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Remove bumper— 2 fixings in each wheel arch liner. 1 fixing behind each arch liner. 2 fixings on top edge of bumper and 2 on lower face. Pull out bumper tips and pull rearwards. Disconnect reversing sensors if fitted. Remove under tray if fitted. 2. Remove impact beam. 3. Insert captive straps CS inside the chassis rails and locate through holes provided. Loosely attach side plates LSP and RSP to captive straps using nuts NT with washers WA. 4. Loosely attach crossbar CB to side plates using set screws B and washers WB. Tighten all fixings. 5. Refit impact beam. 6. Replace bumper. Cut out a slot in the under tray (if fitted) 90 x 100 deep, and refit.
Detachable Neck: Attach to crossbar CB using set screws Z. Swan Neck: Attach to crossbar CB with CPE10 plates ( standard orientation ) using set screws Y & bolts W. Flange Neck: Attach to crossbar CB using set screws A. Attach type approved towball (not supplied) using set screws G. 7. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
258E 258ED 258ES
Powder Coated Finish
FORD FOCUS III ESTATE
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com