Rev 2:2
280E 280ES 280ED
LANDROVER DISCOVERY SPORT 2014Powder Coated Finish
7 seat With Spare Wheel Underneath Vehicle E11 55R-0110788 w1517
Components Code Mainframe
Quantity
Bolt Kit
Description
Code
Quantity
Description
CB
1
Crossbar
WA
8
14mm Large Round Washers
LA
1
Left Angle
B
8
14x110 Bolts & Grip Washers
RA
1
Right Angle
C
4
12x40 Set Screws, Nuts & Grip Washers
EB
2
Exhaust Brackets
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1.
Remove light clusters, 2 plastic fixings inside boot.
2.
Remove lower plastic valance, 2 screws.
3.
Remove bumper, 2 screws and 2 tailgate stops on boot shut panel, 4 bolts on lower edge. Unclip wheel arch surrounds and disconnect sensors, remove 2 screws in wheel arches and 1 tip bolt, unclip top edges of bumper and pull rearwards, disconnect reverse sensors.
4.
Lower exhaust silencers on 4 rubber hangers. Disconnect sensor and wiring from impact beam, remove impact beam with 6 bolts.
5.
Remove towing eye from inside right hand chassis on 2 bolts, remove bumper support brackets from impact beam.
6.
Insert angles LA and RA inside the the chassis and loosely attach using bolts B and washers WA along with exhaust hanger brackets EB. NOTE: Cut heat shields to suit exhaust hanger brackets EB.
7.
Loosely attach crossbar CB to the angles LA and RA using set screws C. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
8.
Re attach exhaust to vehicle, Attach bumper support brackets to the crossbar using original fixings. Attach sensor to the crossbar using original fixings.
9.
Cut bumper and lower valance as in diagram, re-attach bumper, valance and lights.
10. Detachable Neck: Attach to crossbar CB using set screws Z. 11. Swan Neck: Attach to crossbar CB with CPE10 plates (reversed orientation) using set screws Y and W. 12. Flange Neck: Attach to crossbar CB using bolts A. Attach type approved towbal (not supplied) using set screws G. 13. Check and tighten all fasteners using a calibrated torque tool to the recommended torque setting on the towbar drawing. PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:2
280E 280ES 280ED
Powder Coated Finish
LANDROVER DISCOVERY SPORT 20147 Seat With Spare Wheel Underneath Vehicle
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com