Rev 2:1
562E
RENAULT MEGANE II HATCHBACK (Inc Facelift) 2002-2009
Powder Coated Finish
e11*94/20*8309*00 Components
Code
Quantity
CB
1
LS
1
Rs
1
AN
Description
Bolt Kit Code
Quantity
Crossbar
WA
2
10mm Large Round Washers
Left Strap
WB
6
12mm Large Round Washers
Right Strap
E
2
16x50 Set Screws,Nuts & Grip Washers
1
Angle
G
1
10x30 Set Screw & Grip Washer
CP
1
Captive Plate
C
2
10x35 Set Screws & Grip Washers
F
1
Flange Neck
B
6
12x40 Set Screws,Grip Washers & 2 Nuts
A
2
12x100 Bolts, Nuts & Grip Washers
w1055
Description
1. Remove rear light clusters (2 thumbscrews, 1 at the top, 1 behind round pop of cover) gently pull cluster rearwards. 2. Remove bumper – 2 fixings on top edge in light cluster area, 3 fixings on inside of wheel arches, 5 fixings on lower edge of bumper. Gently pull out tips of bumper and pull rearwards. 3. Remove impact beam. (Keep with vehicle for refit if the towbar is removed). Remove silver foil from ends of chassis and remove metal tab covering access to the inside of left chassis rail. Remove bolt securing exhaust hanger bracket. Remove boot floor covering, remove spare wheel, jack and holder. Remove plastic bung from the bottom of the right chassis rail inside the boot. Remove air vent from the left outer rear panel. Peel of any tape covering fixing points inside the boot. 4. Insert captive plate CP Inside the right chassis and loosely attach angle AN to the bottom of the right chassis rail inside the boot using set screws G. 5. Insert left strap LS and right strap RS inside the chassis rails and loosely attach using set screws C and washers WA. 6. Insert crossbar CB inside the chassis rails and attach using set screws B and washers WB. (Access to the left rearmost fixing point is gained through the outer left hand air vent.) 7. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing. 8.
It is recommended that the ends of the chassis rails are sealed (sealant not provided ) to prevent water ingress. Replace bumper. Note — The lower centre bumper fixing may need to be trimmed. 9. Replace rear lights and secure exhaust hanger bracket using original bolt. 10. Attach flange neck F to mainframe CB bolts A. Attach tow ball A50/1 (not supplied) using set screws E. 11. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
562E
Powder Coated Finish
RENAULT MEGANE II HATCHBACK (Inc Facelift)
Bolt Torque Settings Bolt Size (mm)
Pitch (mm)
Torque Setting (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com