Rev 2:1
626E
FLANGE NECK
Powder Coated
Components Code
Quantity
F
1
Bolt Kit
Description
Flange Neck
Code
Quantity
A G
2 2
w493
Description
12x100 Bolts, Nuts & Grip Washers 16x50 Set Screws, Nuts & Grip Washers
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
626E 626ED 626ES
Powder Coated Finish
AUDI A6 SALOON & AVANT ESTATE
(Exc All Road & S Line With Colour Coded Bumper) e11*94/20*6242*01 w630
Components
Mainframe
Code
Quantity
CB
1
Crossbar
AN
2
Angles
Bolt Kit
Description
Code
Quantity
Description
WA
6
10mm Large Round Washers
B
2
12x35 Set Screws, Nuts & Grip Washers
C
2
12x35 Set Screws & Grip Washers
E
4
10x100 Bolts, Grip Washers & 2 Nuts
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Remove rear bumper. (Remove boot floor covering and side panels, remove 2 nuts each side under lights, remove rear panel and plastic grommets to reveal 1 nut each side and remove. Remove 3 screws at each wheel arch and 2 fixings on bottom edge of bumper). 2. Remove inner crush beam and mounting arms. 3. Insert angles AN into the chassis rails and loosely attach using bolts E and washers WA. Attach mainframe CB to the angles AN using bolts B and C. Tighten bolts. 4. Cut bumper as shown in diagram and replace. Detachable Neck: Attach detachable neck D to crossbar CB using set screws Z.
Swan Neck: Attach swan neck SN to crossbar CB with IP plates using fasteners A.
Flange Neck: Attach flange neck F to crossbar CB using bolts A. Attach type approved towball ( not supplied ) using set screws G.
5. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
626E 626ED 626ES
Powder Coated
AUDI A6 SALOON & AVANT ESTATE
(Exc All Road & S Line With Colour Coded Bumper)
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com