Rev 2:1
629E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description
Flange Neck
Code
Quantity
A G
2 2
w493
Description
12x100 Bolts, Nuts & Grip Washers 16x50 Set Screws, Nuts & Grip Washers
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
629E 629ED 629ES
Powder Coated Finish
BMW X3 (E83) 2004-2011 (Inc Sports Bumper) e11*94/20*7998*01 w
Components
Mainframe
Code
Quantity
CB
1
Description
Bolt Kit Code
Quantity
X
4
Crossbar
Description Use Existing BMW Fixings
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Remove rear bumper:- three fixings along lower edge. 2. Remove centre cover panel in bumper (where fitted). Cut out the raised marked area inside the bumper. Cut two slots in panel as shown in diagram (if required trim to suit). 3. Remove covers on boot hatch panel from each corner. This will reveal one fixing each side, two fixings on wheel arch covers, two fixings inside wheel arch covers and one fixing at each bumper tip. 4. Pull bumper rearwards and disconnect sensors. 5. Remove and discard rear impact beam, but retain existing nuts. 6. Attach cross bar CB to studs on rear panel using existing impact beam nuts X. Fully tighten to 71nm. Thread lock is recommended. 7. Refit bumper and sensors. Detachable Neck: Attach to crossbar CB using fasteners Z. Swan Neck: Attach swan neck SN to crossbar CB with IP plates using bolts A. Flange Neck: Attach to crossbar CB using bolts A. 9. Attach type approved towball (not supplied) using set screws G. 8. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
629E 629ED 629ES
Powder Coated Finish
BMW X3 (E83) (Inc Sports Bumper)
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com