Rev 2:1
661E
FLANGE NECK
Powder Coated Finish
Components Code
Quantity
F
1
Bolt Kit
Description Flange Neck
Code
Quantity
A
2
12x100 Bolts, Nuts & Grip Washers
G
2
16x50 Set Screws, Nuts & Grip Washers
w493
Description
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
661E 661ED 661ES
Powder Coated Finish
MERCEDES A CLASS (W169) MERCEDES B CLASS (W245)
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch Torque Setting (mm) (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
661E 661ED 661ES
Powder Coated Finish
MERCEDES A CLASS (W169) 2005-2012 MERCEDES B CLASS (W245) 2005-2012
e11*94/20*6130*00 w762
Components
Mainframe
Code
Quantity
Description
Bolt Kit Code
Quantity
Description
CB
1
Crossbar
WA
8
10mm Large Round Washers
LSP
1
Left Strap
WB
4
12mm Large Round Washers
RST
1
Right Strap
WC
4
10mm Small Round Washers
B
8
10x40 Bolts & Grip Washers
C
2
12x40 Bolts, Nuts & Grip Washers
E
4
10x30 Bolts, Nuts & Grip Washers
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Remove bumper (4 fixings across top edge behind covers, 4 fixings on lower edge, 1 plastic clip each side of wheel arch liners, 1 tip screw each side behind wheel arch liners). Remove bumper beam. 2. Remove spare wheel and boot floor covering, (tucked under each side and rear panels, no fixing). Remove rearmost rubber grommets from inside of the chassis rails. 3. Insert straps RST and LST into the chassis rails and loosely secure using bolts B with washers WA. Loosely attach crossbar CB to the rear panel using bolts B and C using washers WA and WB. Loosely attach crossbar CB to straps RST and LST using bolts E and washers WC. Tighten all bolts. 4. Cut bumper as shown in diagram Detachable Neck: Atttach to crossbar CB using set screws Z. Swan Neck: Attach to crossbar CB with IP plates using bolts A. Flange Neck: Attach to crossbar CB using bolts A. Attach type approved towball (not supplied) using ddddfasteners G. 5. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings ccvc ddddrecommended on the towbar.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com