Rev 2:1
695E 695ED 695ES
Powder Coated Finish
AUDI A4 SALOON (8EC) A4 AVANT ESTATE (8EC) (Inc Quattro & S Line) (Exc S4) & SEAT EXEO (Saloon & Estate) e11*94/20*6440*02 w710
Components
Mainframe
Code
Quantity
CB
1
Crossbar
LP
1
Left Side Plate
RP
1
Right Side Plate
Bolt Kit
Description
Code
Quantity
Description
WA
6
10mm Large Round Washers
B
4
12x40 Bolts, Nuts & Grip Washers
C
2
5x20 Bolts, Nuts & Grip Washers
G
4
10x100 Bolts, Nuts & Grip Washers
(Neck Type) Detachable 'D'
Please See Detachable Neck Box Contents List
Please See Detachable Neck Box Contents List
Swan Neck 'S'
Please See Swan Neck Box Contents List
Please See Swan Neck Box Contents List
Flange Neck 'F'
Please See Flange Neck Box Contents List
Please See Flange Neck Box Contents List
1. Remove boot floor covering and rear panel. 2. Remove bumper (six nuts each side inside vehicle, two torx head screws behind wheel arch liners—also retained with torx screws, five torx screws along lower edge of bumper. Pull out bumper tips and pull the bumper rearwards). 3. Remove and discard the bumper impact beam. 4. Temporarily lower exhaust hangers and remove heat shield. 5. Remove tape from forward mounting points. Insert angles LA and RA into the chassis rails and loosely attach using fasteners G with washers WA. 6. Loosely attach mainframe CB to the angles LA and RA using fasteners B. Check and tighten all fasteners. 7. Replace heat shield and exhaust hangers. 8. Cut out a slot in the bottom centre edge of the bumper 90mm wide and 50mm deep and refit the bumper.
Detachable neck: Attach detachable neck D to crossbar CB using set screws Z. Swan Neck: Attach swan neck SN to crossbar CB with IP plates using fasteners A. Flange Neck: Attach flange neck F to crossbar CB using bolts A. Attach type approved towball ( not supplied ) using set screws G. 9. Check and tighten all fasteners using a calibrated torque tool to the specified torque settings recommended on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
695E 695ED 695ES
Powder Coated
AUDI A4 SALOON (8EC) A4 AVANT ESTATE (8EC) (Inc Quattro & S Line) (Exc S4) & SEAT EXEO (Saloon & Estate)
VOLKSWAGEN PASSAT SALOON/ ESTATE 2014-
Bolt Torque Settings Bolt Size (mm)
Pitch (mm)
Torque Setting (Nm) 8.8 Tensile
5
0.80
6.09
6
1.00
10.50
8
1.25
25.30
10
1.25
46.00
10
1.50
50.90
12
1.25
83.00
12
1.50
87.81
12
1.75
87.27
14
2.00
139.00
16
2.00
213.00
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com
Rev 2:1
695E
FLANGE NECK
Powder Coated
Components Code
Quantity
F
1
Bolt Kit
Description
Flange Neck
Code
Quantity
A G
2 2
w493
Description
12x100 Bolts, Nuts & Grip Washers 16x50 Set Screws, Nuts & Grip Washers
1. Loosely attach flange neck F using bolts A. 2. Loosely attach type approved towball (not supplied) using set screws G. 3. Tighten all fixings using a calibrated torque tool to the torque settings specified on the towbar drawing.
PLEASE REFER TO YOUR VEHICLE HANDBOOK FOR THE MAXIMUM TOWING WEIGHT This product is finished in a revolutionary industry leading powder coat finish.
Towsure Products Limited, Holme Lane, Hillsborough, Sheffield, S6 4JR T: 0114 250 3000 E: sales@towsure.com
www.towsure.com