Graco pompen voor voedingsmiddelen industrie by Wiltec B.V.

SaniForce Equipment Catalog â&#x201E;˘

Solutions for Sanitary Applications

Proven Quality. Leading Technology.

Table of Contents SaniForce Equipment Catalog ™

Contents SaniForce Pump Selection Chart..................................................................................................................... 2 SaniForce Drum and Bin Unloader Selection Chart.......................................................................................... 4 SaniForce 1040, 1590 & 2150........................................................................................................................ 6 SaniForce 1590 & 3150 High Sanitation Pumps............................................................................................ 10 SaniForce 1590 & 3150 3A Certified Pumps................................................................................................... 13 SaniForce Meat and Poultry Pumps ................................................................................................................ 15 SaniForce Piston Pumps................................................................................................................................. 17 SaniForce Drum Unloaders............................................................................................................................. 20 SaniForce Bin Evacuation Systems (BES)........................................................................................................ 22 Hydra-Clean® Pressure Washers..................................................................................................................... 25 Overmolded Diaphragms................................................................................................................................ 28

CONTENTS

SaniForceâ&#x201E;˘ Pumps Selection Chart

1040

1590

2150

1590 HS

3150 HS

Max Flow Rate

151 l/min (40 gpm)

341 l/min (90 gpm)

568 l/min (150 gpm)

340 l/min (90 gpm)

568 l/min (150 gpm)

Max Fluid Pressure

8 bar

(0.8 MPa - 120 psi)

Check Style

Ball

Ball and Flapper

Suction Lift (Wet)

8.84 m (29 ft)

8.5 m (28 ft)

Ball = 5.5 m (18 ft) Flapper = 3 m (10 ft)

Max Pumpable Solids

3.2 mm (1/8")

4.8 mm (3/16")

6.3 mm (1/4")

15.9 mm (5/8")

Ball = 25.4 mm (1") Flapper = 63.5 mm (2.5")

Viscosity Range

Up to 10,000 cps

Up to 15,000 cps

Up to 20,000 cps

Up to 25,000 cps

Up to 20,000 cps

Leaflet

320462

338499

Instruction Manual

311879

310622

SANIFORCE pump selection chart Section description

SaniForceâ&#x201E;˘ Pumps Selection Chart

1590 3A

3150 3A

Meat/Poultry

340 l/min (90 gpm) 568 l/min (150 gpm) 568 l/min (150 gpm)

8 bar

(0.8 MPa - 120 psi) (0.8 MPa - 120 psi) (0.8 MPa - 120 psi) Ball

Ball

Flapper

8.5 m (28 ft)

5.5 m (18 ft)

3 m (10 ft)

15.9 mm (5/8")

25.4 mm (1")

6.3 cm (2.5")

Up to 15,000 cps

Up to 20,000 cps

Up to 25,000 cps

338499

338067

310622

SaniForce 6:1 Piston Pump

SaniForce 5:1 Piston Pump

SaniForce 12:1 Piston Pump

15 l/min (4 gpm)

53 l/min (14 gpm)

32 l/min (8.5 gpm)

41 bar

28 bar

83 bar

(4.1 MPa - 600 psi)

(2.8 MPa - 400 psi)

(8.3 MPa - 1200 psi)

Double ball or Priming piston

Priming piston

N/A

3.2 mm (1/8")

6.4 mm (1/4")

Siphon: Up to 5,000 cps Immersion: Up to 100,000 cps

338591

3A0733

3A0734

3A0735

SANIFORCE pump selection chart

SaniForce Drum and Bin Unloaders Selection Chart

SaniForce 6:1 Drum Unloader Max Flow Rate

15 l/min (4.0 gpm)

SaniForce 5:1 Drum Unloader 53 l/min (14 gpm)

SaniForce 12:1 Drum Unloader 32 l/min (8.5 gpm)

SaniForce 3150 HS Drum Unloader 234 l/min (60 gpm) to 390 l/min (100 gpm)

Max Fluid Pressure Pump Style Controls

41 bar

28 bar

83 bar

8 bar

(4.1 MPa - 600 psi)

(2.8 MPa - 400 psi)

(8.3 MPa - 1200 psi)

(0.8 MPa - 120 psi)

Double ball or

Priming piston

Ball and flapper

priming piston

Manual

25,000-60,000 cps

Viscosity Range Double Ball:

60,000-500,000 cps

Leaflet

338590

Instruction Manual

3A0591

Priming Piston

25,000-100,000 cps

SANIFORCE Drum and Bin Unloader Selection Chart Section description

SaniForce Drum and Bin Unloaders Selection Chart

SaniForce 2150 Drum Unloader

SaniForce BES

SaniForce 3150 BES

234 l/min (60 gpm) to

106 l/min (28 gpm) to

468 l/min (120 gpm) to

390 l/min (100 gpm)

204 l/min (54 gpm)

1,135 l/min (300 gpm)

8 bar

27.5 bar (2.7 MPa - 400 psi) to

8 bar

(0.8 MPa - 120 psi)

70 bar (7 MPa - 1000 psi)

(0.8 MPa - 120 psi)

Ball

Double ball or

Ball and flapper

priming piston Manual

Manual and Electronic

25,000-100,000 cps

25,000-500,000 cps

25,000-100,000 cps

338590

338589

3A0591

311163

SANIFORCE Drum and Bin Unloader Selection Chart

SaniForce 1040, 1590 & 2150 Air-Operated Diaphragm Pumps Ordering Information SaniForce 1040 Part Number Size

Seats

O-rings

Balls

Diaphragms

FD1111

SST

PTFE

1.5"

FD1122

1.5"

SST

PTFE

Santoprene

FD1211

1.5"

SST

EPDM

PTFE

FD1222

1.5"

SST

EPDM

Santoprene

FD1113

1.5"

SST

PTFE

Overmolded PTFE

FD1213

1.5"

SST

EPDM

PTFE

Overmolded PTFE

FD1132

1.5"

SST

PTFE

Weighted Polychloroprene

Santoprene

FD1232

1.5"

SST

EPDM

Weighted Polychloroprene

Santoprene

SaniForce 1590 Part Number Size

Seats

O-rings

Balls

Diaphragms

FD2111

SST

PTFE

FD2122

SST

PTFE

Santoprene

FD2211

SST

EPDM

PTFE

FD2222

SST

EPDM

Santoprene

FD2113

SST

PTFE

Overmolded PTFE

FD2213

SST

EPDM

PTFE

Overmolded PTFE

FD2132

SST

PTFE

Weighted Polychloroprene

Santoprene

FD2232

SST

EPDM

Weighted Polychloroprene

Santoprene

SaniForce 2150

Part Number Size

Seats

O-rings

Balls

Diaphragms

FD3111

SST

PTFE

2.5"

FD3122

2.5"

SST

PTFE

Santoprene

FD3211

2.5"

SST

EPDM

PTFE

FD3222

2.5"

SST

EPDM

Santoprene

FD3113

2.5"

SST

PTFE

Overmolded PTFE

FD3213

2.5"

SST

EPDM

PTFE

Overmolded PTFE

FD3132

2.5"

SST

PTFE

Weighted Polychloroprene

Santoprene

FD3232

2.5"

SST

EPDM

Weighted Polychloroprene

Santoprene

Air-Operated diaphragm pumps

SaniForce 1040, 1590 & 2150

Ordering Information Fluid Repair Kits Kits

O-rings

Balls

Diaphragms

1040 Fluid Repair Kits

Kits

O-rings

Balls

Diaphragms

1590 Fluid Repair Kits (cont.)

FK1111

PTFE

FK2113

PTFE

Overmolded PTFE

FK1122

PTFE

Santoprene

FK2213

EPDM

PTFE

Overmolded PTFE

FK1211

EPDM

PTFE

FK2132

PTFE

Weighted CR

Santoprene

FK1222

EPDM

Santoprene

FK2232

EPDM

Weighted CR

Santoprene

FK1113

PTFE

Overmolded PTFE

2150 Fluid Repair Kits

FK1213

EPDM

PTFE

Overmolded PTFE

FK3111

PTFE

FK1132

PTFE

Weighted CR

Santoprene

FK3122

PTFE

Santoprene

FK1232

EPDM

Weighted CR

Santoprene

FK3211

EPDM

PTFE

1590 Fluid Repair Kits

FK3222

EPDM

Santoprene

FK2111

PTFE

FK3113

PTFE

Overmolded PTFE

FK2122

PTFE

Santoprene

FK3213

EPDM

PTFE

Overmolded PTFE

FK2211

EPDM

PTFE

FK3132

PTFE

Weighted CR

Santoprene

FK2222

EPDM

Santoprene

FK3232

EPDM

Weighted CR

Santoprene

Technical Specifications

Maximum fluid working pressure Air pressure operating range Maximum air consumption Air consumption Maximum free-flow delivery Liters (gallons) per cycle Maximum suction lift Maximum size pumpable solids Air inlet size Fluid inlet/outlet size Weight - All models Leaflet Instruction manual

1040 FDA

1590 FDA

2150 FDA

8 bar (0.8 MPa - 120 psi) 1.4–8 bar (0.14-0.8 MPa / 20-120 psi) 1.4 m3/min (50 scfm) 0.51 m3 at 4.8 bar/75l/min (18 scfm at 70 psi/20 gpm) 151 l/min (40 gpm) 0.57 (0.16)* 8.83 m (29 ft) wet, 4.87 m (16 ft) dry 3.2 mm (1/8") 0.5" npt(f) 1.5" sanitary flange 24.9 kg (55 lb) 320462 311879

8 bar (0.8 MPa - 120 psi) 1.4–8 bar (0.14 –0.8 MPa / 20–120 psi) 3.7 m3/min (130 scfm) 1.2 m3 at 4.8 bar/190 l/min (42 scfm at 70 psi/50 gpm) 341 l/min (90 gpm) 1.9 (0.5)* 8.83 m (29 ft) wet, 4.27 m (14 ft) dry 4.8 mm (3/16") 0.5" npt(f) 2" sanitary flange 40 kg (89 lb) 320462 311879

8 bar (0.8 MPa - 120 psi) 1.4–8 bar (0.14 –0.8 MPa / 20–120 psi) 5.05 m3/min (175 scfm) 2.0 m3 at 4.8 bar/300 l/min (70 scfm at 70 psi/80 gpm) 568 l/min (150 gpm) 3.67 (0.97)* 8.83 m (29 ft) wet, 4.87 m (16 ft) dry 6.3 mm (1/4") 0.5" npt(f) 2.5" sanitary flange 66.7 kg (147 lb) 320462 311879

Maximum fluid operating temperature is based on the following maximum diaphragm, ball, and seat temperature ratings Stainless steel PTFE Santoprene EPDM Polychloroprene

121.1°C (250°F) 104.4°C (220°F) 82.2°C (180°F) 135°C (275°F) 93.3°C (200°F)

* Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type

Air-Operated diaphragm pumps

SaniForce 1040, 1590 & 2150

Performance Charts 1590Performance Performance 1590

1040Performance Performance 1040

CYCLES PER MINUTE

CYCLES PER MINUTE 99

132

165

197

230

100 (0.7, 7)

50 (1.42)

40 (1.13)

80 (0.55, 5.5) 60 (0.41, 4.1)

40 (0.28, 2.8)

263 60 (1.7)

30 (0.85)

20 (0.57) 10 (0.28)

20 (0.14, 1.4) 0

5 (19)

10 (38)

15 (57)

20 (76)

25 (95)

30 (114)

35 (133)

40 (152)

gpm (l/min)

A B C D

= at 120 psi (8.4 bar, 0.84 MPa) = atA 8.4 bar (0.84 MPa - 120 psi) 100 MPa psi (7- bar, = atB 7 =barat (0.7 1000.7 psi)MPa) = atC 4.8 MPabar, - 700.5psi) = bar at 70(0.48 psi (4.8 MPa) = at 2.8 bar (0.28 MPa - 40 psi) D = at 40 psi (2.8 bar, 0.3 MPa)

120 (0.84, 8.4)

100 (0.7, 7)

CYCLES PER MINUTE CYCLES PER MINUTE

117

136

80 (0.55, 5.5)

40 (0.28, 2.8)

120 (3.4)

90 (2.54) 60 (1.7)

30 (0.85)

20 (0.14, 1.4) 0

20 (75)

40 (151)

60 (227)

80 (302)

100 (378)

120 (454)

140 (530)

FLOW FLUID FLUID FLOW gpm (lpm) gpm (l/min)

AIR PRESSURE AIR PRESSURE = atbar 120(0.84 psi (8.4 0.84psi) MPa) A =Aat 8.4 MPabar, - 120 at 100 (7 bar, 0.7psi) MPa) B =Bat 7= bar (0.7psi MPa - 100

LEGEND LEGEND Air Consumption Air Consumption - - - - -

Fluid Flow Fluid Flow __________

C =Cat 4.8 MPa 70 psi) = atbar 70 (0.48 psi (4.8 bar,- 0.5 MPa) D = at 2.8 bar (0.28 MPa - 40 psi) D = at 40 psi (2.8 bar, 0.3 MPa)

155 180 (5.1)

B C

60 (0.41, 4.1)

Air-Operated diaphragm pumps

160

160 (605)

200

100 (0.7, 7)

80 (0.55, 5.5)

60 (0.41, 4.1) 40 (0.28, 2.8)

240 140 (3.96) 120 (3.4) 100 (2.83) 80 (2.27) 60 (1.7) 40 (1.13)

20 (0.14, 1.4)

20 (0.57) 20 (75)

40 (151)

60 (227)

AIR PRESSURE AIR PRESSURE = at psi MPa (8.4 bar, 0.84 A = at bar120 (0.84 - 120 psi)MPa) A 8.4 B = at 1000.7 psi)MPa) at (0.7 100 MPa psi (7-bar, B 7=bar C = at 4.8 bar (0.48 MPa - 70 psi) = at psi (4.8 0.5psi) MPa) C 2.8 D = at bar70(0.28 MPabar, - 40 D = at 40 psi (2.8 bar, 0.3 MPa)

150 (4.25)

120

gpm (l/min)

3 AIR CONSUMPTION CONSUMPTION scfm (mscfm /min)(m 3/min) AIR

FLUID OUTLET PRESSURE psi (bar,psi MPA) FLUID OUTLET PRESSURE (MPa, bar)

80 (302)

FLUID FLOW FLOW FLUID

LEGEND LEGEND Air Consumption Air Consumption - - - - Fluid Flow Fluid Flow __________

2150Performance Performance 2150 0

120 (0.84, 8.4)

FLOW FLUIDFLUID FLOW gpm (lpm) AIR PRESSURE AIR PRESSURE

140 (0.96, 9.6)

100 (378)

120 (454)

gpm (lpm)

LEGEND LEGEND Air Consumption Air Consumption - - - - Fluid Flow __________ Fluid Flow

AIR CONSUMPTION scfm (m33/min) AIR CONSUMPTION /min)

OUTLETPRESSURE PRESSURE psi (bar, MPA) bar) FLUID FLUID OUTLET psi (MPa,

3 AIRCONSUMPTION CONSUMPTION scfm (mscfm /min)(m 3/min) AIR

FLUIDOUTLET OUTLET PRESSURE psi (bar, MPA) FLUID PRESSURE psi (MPa, bar)

0 120 (0.84, 8.4)

CYCLES PER MINUTE

SaniForce 1040, 1590 & 2150

Dimensions SaniForce 1040

SaniForce 1590 414 mm (16.3 in)

495 mm (19.5 in)

1-1/2Outlet in Outlet 1-1/2" Sanitary Flange Sanitary Flange

216 mm (8.5 in)

249 mm (9.8 in)

Air Inlet 1/2 npt(f)

2" Outlet 2 in Outlet Sanitary Flange Sanitary Flange

Air Inlet 1/2 npt(f)

335 mm (13.2 in)

429 mm (16.9 in) 518 mm (20.4 in)

411 mm (16.2 in)

259 mm (10.2 in)

320 mm (12.6 in)

51 mm (2.0 in) Air Exhaust Air Exhaust (muffler included) (muffler included) 3/4 npt(f) 3/4 npt(f)

61 mm (2.4 in)

1-1/2 1-1/2" Inletin Inlet Sanitary Flange Sanitary Flange

188 mm (7.4 in)

AirAirExhaust Exhaust (muffler included) included) (muffler 3/4 npt(f) npt(f) 3/4

Overall 8.2 (208 mm) OverallWidth Width ==82 inchin(208 mm)

198 mm (7.8 in)

in Inlet 1-1/2"2Inlet Sanitary Flange Sanitary Flange

Overall Width = 10.1 inch (257 mm) Overall Width = 257 mm (10.1 in)

SaniForce 2150 SaniForce 1040 SaniForce 1040 Mounting Hole Pattern Mounting Hole Pattern

559 mm (22.0 in)

2-1/2 in Outlet 2-1/2" Outlet Sanitary Flange Sanitary Flange

276 mm (10.9 in)

5.0 in (127 mm)

Four 0.42" 0.42 in Four (10.7mm) mm) (10.7 diameterholes holes diameter

7.4 in (188 mm)

SaniForce 1590 SaniForce 1590 Mounting Hole Pattern Mounting Hole Pattern

Air Inlet 1/2 npt(f)

556 mm (21.9 in) 660 mm (26.0 in)

6.0 in (152 mm)

401 mm (15.8 in)

Four 0.46" 0.46 in (11.7mm) mm) (11.7 diameter holes diameter holes

7.8 in (198 mm)

SaniForce 2150 SaniForce 2150 Mounting Hole Pattern Mounting Hole Pattern 63 mm (2.5 in)

Air Exhaust Air Exhaust (muffler (mufflerincluded) included) npt(f) 3/43/4npt(f)

208 mm (8.2 in) Overall Width= = 12.3 (312(12.3 mm) in) Overall Width 312inch mm

2-1/2 2-1/2" Inletin Inlet Sanitary Flange Sanitary Flange

6.3 in (160 mm)

Four 0.46 0.46"in Four (11.7 (11.7 mm) mm) diameter diameter holes holes

8.2 in (209 mm)

Air-Operated diaphragm pumps

SaniForce 1590 & 3150 HS High Sanitation Diaphragm Pumps Ordering Information SaniForce 1590 HS Ball Pumps Part Number

Type

Inlet

Ball

Diaphragm

SBBAAA

Ball

2" x 2"

PTFE

Overmolded EPDM

SBBA11

Ball

2" x 2"

PTFE

SABA13

Ball

2" x 2"

PTFE

Overmolded PTFE

SBBA13

Ball

2" x 2"

PTFE

Overmolded PTFE

SBBA22

Ball

2" x 2"

Santoprene

Includes leak detector

SaniForce 1590 Kits and Accessories Part Number

Type

Part Number

Type

255058

Overmolded EPDM diaphragm kit

112421

Santoprene ball (quantity one)

255059

Santoprene diaphragm kit

112419

PTFE ball (quantity one)

255060

PTFE diaphragm kit

255122

Air valve repair kit 3A

15D990

Leak detector

SaniForce 3150 HS Ball Pumps Part Number SA13A1 SA23A1 SA3AA1 SA33A1 SA4AA1 SA43A1 SA53A1 SA3361 SB2AA1 SB3AA1 SB2661 SB3661 SB2771 SB3771 SB2881 SB3881

Type Ball Check Ball Check Ball Check Ball Check Ball Check Ball Check Ball Check Ball Check Ball Check Ball Check Ball Check Ball Check Ball Check Ball Check Ball Check Ball Check

Inlet/ Outlet Size 1.5" x 1.5" 2" x 2" 3" x 3" 3" x 3" 4" x 4" 4" x 4" 3" x 2" 3" x 3" 2" x 2" 3" x 3" 2" x 2" 3" x 3" 2" x 2" 3" x 3" 2" x 2" 3" x 3"

Diaphragm Overmolded PTFE/EPDM Overmolded PTFE/EPDM Overmolded EPDM Overmolded PTFE/EPDM Overmolded EPDM Overmolded PTFE/EPDM Overmolded PTFE/EPDM Overmolded PTFE/EPDM Overmolded EPDM Overmolded EPDM Santoprene Santoprene Buna-N Buna-N Fluoroelastomer Fluoroelastomer

Ball Material PTFE PTFE PTFE PTFE PTFE PTFE PTFE Santoprene PTFE PTFE Santoprene Santoprene Buna-N Buna-N Fluoroelastomer Fluoroelastomer

SaniForce 3150 HS Flapper Pumps Part Number SF3AF1 SF4AF1 SF36F1 SF46F1 SF37F1 SF47F1 SF38F1 SF48F1

Type Flapper Flapper Flapper Flapper Flapper Flapper Flapper Flapper

Inlet/ Outlet Size 3" x 3" 4" x 4" 3" x 3" 4" x 4" 3" x 3" 4" x 4" 3" x 3" 4" x 4"

Diaphragm Material Overmolded EPDM Overmolded EPDM Santoprene Santoprene Buna-N Buna-N Fluoroelastomer Fluoroelastomer

Air-Operated diaphragm pumps

Flapper Check Valve

Ball Check Valve

SaniForce 1590 & 3150 HS

Ordering Information SaniForce 3150 HS Accessories Part Number

Type

16E975 15H461 15E285 112359 112361 253225 15B492 253223 15B491 253222 253224 253628 15D990

Conversion kit: Ball to flapper, includes four flapper assemblies 3A Conversion kit: Flapper to ball, includes four housing retainers (balls need to be ordered separately) Conversion kit: Flapper to ball, includes four housing retainers (balls need to be ordered separately) PTFE ball (order quantity four) Santoprene ball (order quantity four) Santoprene diaphragm kit Buna-N ball (order quantity four) Buna-N diaphragm kit Fluoroelastomer ball (order quantity four) Fluoroelastomer diaphragm kit Overmolded EPDM diaphragm kit Overmolded PTFE diaphragm kit Leak detector kit

Technical Specifications 1590 Maximum fluid working pressure Maximum free-flow delivery Maximum suction lift Maximum size pumpable solids Air pressure operating range Maximum air consumption Air consumption at 4.8 bar (70 psi) air inlet pressure/227 l/min (60 gpm) Maximum pump speed *Liters (gallons) per cycle **Maximum noise level at 6.8 bar (100 psi), full flow **Sound power level **Noise level at 4.8 bar (70 psi) and 50 cpm Air inlet size Weight Leaflet Instruction manual

Maximum fluid working pressure Maximum free-flow delivery* Maximum suction lift - ball Maximum suction lift - flapper Maximum size pumpable solids - ball Maximum size pumpable solids - flapper

1.42 m3/min (50 scfm)

Air pressure operating range

200 cpm 1.96 (0.5)

Maximum air consumption Air consumption at 4.8 bar (70 psi) air inlet pressure/227 l/min (60 gpm) Maximum pump speed *Liters (gallons) per cycle **Maximum noise level at 6.8 bar (100 psi), full flow **Sound power level **Noise level at 4.8 bar (70 psi) and 50 cpm Fluid inlet & outlet size (determined by part number) Air inlet size Weight Leaflet Instruction manual

90 dBa 103 dBa 85 dBa 0.5" npt(f) 44 kg (97 lb) 338499 310622

Maximum fluid operating temperature is based on the following maximum diaphragm, ball, and seat temperature ratings PTFE Santoprene 3A Approved EPDM

3150

8 bar (0.8 MPa - 120 psi) 340 l/min (90 gpm) 8.5 m (28 ft) wet, 4.57 m (15 ft) dry 15.9 mm (5/8") 14-8 bar (014-08 MPa - 20-120 psi) 3.6 m3/min (125 scfm)

104.4°C (220°F) 82.2°C (180°F) 135°C (275°F)

* D isplacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type ** Noise levels measured with the pump mounted on the stand. Sound power measured per ISO Standard 9614-1

8 bar (0.8 MPa - 120 psi) 568 l/min (150 gpm) 5.4 m (18 ft) wet, 2.7 m (9 ft) dry 3.0 m (10 ft) wet, 1.5 m (5 ft) dry 25.4 mm (1 in) 63.5 mm (2.5") 1.4 to 8.4 bar (0.14 to 0.84 MPa - 20-120 psi) 175 scfm 50 scfm 145 cpm 3.90 (1.03) 90 dBa 103 dBa 85 dBa Tri-clamp connections 0.5 in npt(f) 65 kg (145 lb) 338499 310622

Maximum diaphragm operating temperature Santoprene Buna-N PTFE Fluoroelastomer EPDM

82.2ºC (180ºF) 82.2ºC (180ºF) 104.4ºC (220ºF) 121ºC (250ºF) 135ºC (275ºF)

Air-Operated diaphragm pumps

SaniForce 1590 & 3150 HS

Performance Charts 3150 HighSanitation Sanitation Performance 3150 High Performance

1590 HighSanitation Sanitation Performance 1590 High Performance

CYCLES PER MINUTE CYCLES PER MINUTE

120

160

200 A

100 (0.7, 7)

240 B

80 (0.55, 5.5)

C C

60 (0.41, 4.1)

120 (3.96) 100 (3.4)

80 (2.83) 60 (1.7)

40 (0.28, 2.8)

20 (0.14, 1.4)

40 (1.13) E

20 (0.57) 20 (75)

40 (151)

60 (227)

80 (302)

FLUID FLOW FLOW FLUID gpm (l/min)

AIR PRESSURE AIR PRESSURE A B C D E

100 (378)

120 (454)

= at 8.4 bar (0.84 MPa - 120 psi) at 100 (7 -bar, = Bat 7=bar (0.7 psi MPa 1000.7 psi)MPa) = Cat 4.8 MPa - 70 = atbar 70(0.48 psi (4.8 bar, 0.5psi) MPa) = Dat 2.8 MPa - 40 = atbar 40(0.28 psi (2.8 bar, 0.3psi) MPa) = at 1.4 bar (0.14 MPa - 20 psi) E = at 20 psi (1.4 bar, 0.14 MPa)

120 (0.84, 8.4)

100 (0.7, 7)

80 (0.55, 5.5)

60 (0.41, 4.1)

117

136

155

150 (4.2)

125 (3.5)

100 (2.8) 75

(2.1) Model 3150 Dimensional Drawing D

40 (0.28, 2.8)

50 (1.4)

20 (0.14, 1.4)

25 (0.7) 0

20 (75)

40 (151)

60 (227)

80 (302)

100 (378)

120 (454)

140 (531)

3A Bal

160 (606)

FLOW FLUIDFLUID FLOW gpm (lpm) gpm (l/min)

gpm (lpm)

AIR PRESSURE AIR PRESSURE

LEGEND LEGEND

A = at 120 psi (8.4 bar, 0.84 MPa)

3 AIRCONSUMPTION CONSUMPTION scfm (mscfm /min)(m 3/min) AIR

FLUID OUTLET PRESSURE psi (bar,psi MPA) FLUID OUTLET PRESSURE (MPa, bar)

120 (0.84, 8.4)

3 AIR CONSUMPTION CONSUMPTION scfm (mscfm /min)(m 3/min) AIR

FLUID OUTLET PRESSURE psi (bar,psi MPA) FLUID OUTLET PRESSURE (MPa, bar)

CYCLESPER PER MINUTE CYCLES MINUTE

Air Consumption Air Consumption - - - - Fluid Flow Fluid Flow __________

A B C D

LEGEND LEGEND

A = at 120 psi (8.4 bar, 0.84 MPa)

= at 8.4 bar (0.84 MPa - 120 psi) 100MPa psi (7- bar, = atB 7 = barat(0.7 100 0.7 psi)MPa) = atC 4.8 MPabar, - 700.5 psi) = bar at 70(0.48 psi (4.8 MPa) = at 2.8 bar (0.28 MPa - 40 psi) D = at 40 psi (2.8 bar, 0.3 MPa)

Air Consumption Air Consumption - - - - Fluid Flow Fluid Flow __________

721.4 mm (28.4 in)

Dimensions SaniForce 1590 HS

165.1 mm (6.5 in)

SaniForce 3150 HS 22.0 in (558.8 mm)

Ball BallCheck CheckValve ValvePump Pump

Ball Check Valve Ball Check ValvePump Pump

Flappe

632.5 mm (24.9 in)

29.5 in (749.3 mm)

28.3 in (718.8 mm)

37.5 in (952.5 mm)

909.3 mm (35.8 in)

5.9 in (149.9 mm)

218.4 mm (8.6 in)

6.5 in (165.1 mm)

596.9 mm (23.5 in)

Air-Operated diaphragm pumps Air-Operated diaphragm pumps

19.3 in (490.2 mm)

SaniForce 1590 & 3150 3A 3A Certified Diaphragm Pumps Ordering Information SaniForce 1590 3A Pumps Part Number

Type

Inlet

Diaphragm

Ball

SABAAA

3A Approved

2" x 2"

Overmolded EPDM

PTFE

Inlet/Outlet Size

Diaphragm

Ball

1.5" x 1.5"

Overmolded EPDM

PTFE

SaniForce 3150 3A Pumps 3A Pump with Leak Detector Part Number Type SA1AAA

3A Approved

SA2AAA

3A Approved

2" x 2"

Overmolded EPDM

PTFE

SA3AAA

3A Approved

3" x 3"

Overmolded EPDM

PTFE

SA4AAA

3A Approved

4" x 4"

Overmolded EPDM

PTFE

SA5AAA

3A Approved

3" x 2"

Overmolded EPDM

PTFE

Technical Specifications

Maximum fluid working pressure Maximum free-flow delivery** Maximum suction lift - ball Maximum suction lift - flapper Maximum size pumpable solids - ball Maximum size pumpable solids - flapper Typical sound level at 4.9 bar (70 psi) air @ 50 cpm Air pressure operating range Air inlet size Fluid inlet & outlet size (determined by part number) Weight Leaflet Instruction manual

1590 3A Certified

3150 3A Certified

8 bar (0.8 MPa - 120 psi) 340 l/min (90 gpm) 8.5 m (28 ft) wet, 4.5 m (15 ft) dry N/A 15.8 mm (5/8") N/A 85 dBa 1.4 to 8.4 bar (0.14 to 0.84 MPa / 20-120 psi) 0.5" npt(f) Tri-clamp connections 44 kg (97 lb) 338499 310622

8 bar (0.8 MPa - 120 psi) 568 l/min (150 gpm) 5.5 m (18 ft) wet, 2.7 m (9 ft) dry 3.0 m (10 ft) wet, 1.5 m (5 ft) dry 25.4 mm (1") 63.5 mm (2.5") 85 dBa 1.4 to 8.4 bar (0.14 to 0.84 MPa / 20-120 psi) 0.5" npt(f) Tri-clamp connections 65 kg (145 lb) 338499 310622

82.2ºC (180ºF) N/A 104.4ºC (220ºF) N/A 135ºC (275ºF)

82.2ºC (180ºF) 82.2ºC (180ºF) 104.4ºC (220ºF) 121ºC (250ºF) 135ºC (275ºF)

Maximum diaphragm operating temperature Santoprene Buna-N PTFE Fluoroelastomer EPDM ** Flow rates are with muffler and do not vary based on diaphragm material. Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type.

Air-Operated diaphragm pumps

SaniForce 1590 & 3150 3A

Performance Charts 3150 3A 3A Performance 3150 Performance

15903A 3A Performance Performance 1590 80

120

160

100 (0.7, 7)

200

240 120 (3.96)

100 (3.4)

80 (0.55, 5.5)

80 (2.83)

C C

60 (0.41, 4.1)

60 (1.7) D

40 (0.28, 2.8)

20 (0.14, 1.4)

40 (1.13) E

20 (0.57)

20 (75)

40 (151)

60 (227)

80 (302)

FLUID FLOW

FLUID FLOW gpm (l/min) AIR PRESSURE AIR PRESSURE = atbar 120 psi (8.4 0.84 A = Aat 8.4 (0.84 MPabar, - 120 psi)MPa) at 100 (7 -bar, B = Bat 7=bar (0.7 psi MPa 1000.7 psi)MPa)

100 (378)

FLUID OUTLET PRESSURE psi (bar,psi MPA) FLUID OUTLET PRESSURE (MPa, bar)

120 (0.84, 8.4)

3 CONSUMPTION scfm (m /min) AIRAIRCONSUMPTION scfm (m 3/min)

FLUID OUTLET PRESSURE psi (bar, FLUID OUTLET PRESSURE psiMPA) (MPa, bar)

120 (0.84, 8.4)

100 (0.7, 7)

80 (0.55, 5.5)

117

136

150 (4.2)

125 (3.5)

100 (2.8) 75 (2.1)

40 (0.28, 2.8)

50 (1.4)

20 (0.14, 1.4)

25 (0.7) 20 (75)

40 (151)

60 (227)

80 (302)

100 (378)

120 (454)

140 (531)

FLUID FLOW gpm (lpm) FLUID FLOW

gpm (lpm)

gpm (l/min)

AIR PRESSURE AIR PRESSURE

LEGEND LEGEND Air Consumption Air Consumption - - - - -

A B C D

Fluid Flow Fluid Flow __________

C = Cat 4.8 MPa - 70 = atbar 70(0.48 psi (4.8 bar, 0.5psi) MPa) D = at 2.8 bar (0.28 MPa - 40 psi) = at 40 psi (2.8 bar, 0.3psi) MPa) D E = at 1.4 bar (0.14 MPa - 20 E = at 20 psi (1.4 bar, 0.14 MPa)

LEGEND LEGEND

A = at 120 psi (8.4 bar, 0.84 MPa)

= at 8.4 bar (0.84 MPa - 120 psi) = at(0.7 100MPa psi (7- 100 bar, 0.7 = atB 7 bar psi) MPa) = atC 4.8= bar (0.48 MPabar, - 700.5 psi)MPa) at 70 psi (4.8 = atD 2.8= bar (0.28 MPabar, - 400.3 psi)MPa) at 40 psi (2.8

Air Consumption Air Consumption - - - - Fluid Flow Fluid Flow __________

Dimensions SaniForce 1590 3A

Model 3150 Dimensional Drawing SaniForce 3150 3A 3A Ball Check Valve Pump

3A Ball Check Valve Pump

632.5 mm (24.9 in)

721.4 mm (28.4 in)

955.0 mm (37.6 in)

909.3 mm (35.8 in)

218.4 mm (8.6 in)

165.1 mm (6.5 in)

22.0 in (558.8 mm)

596.9 mm (23.5 in)

Ball Check Valve Pump

Air-Operated diaphragm pumps

155

60 (0.41, 4.1)

120 (454)

596.9 mm (23.5 in)

Flapper Check Valve Pumps

160 (606)

3 AIR CONSUMPTION CONSUMPTION scfm (mscfm /min)(m 3/min) AIR

CYCLES PER PER MINUTE CYCLES MINUTE

CYCLES PER MINUTE MINUTE CYCLES PER

SaniForce Meat & Poultry Pumps Air-Operated Diaphragm Pumps Ordering Information Part Number

Type

Inlet/Outlet Size

Diaphragm

SFP6F1

Flapper

3" x 3"

Santoprene

SFP7F1

Flapper

3" x 3"

Buna-N

SFP8F1

Flapper

3" x 3"

Fluoroelastomer

SFPAF1

Flapper

3" x 3"

Overmolded EPDM

Accessories Part Number

Description

253225

Santoprene diaphragm kit

253223

Buna-N diaphragm kit

253222

Fluoroelastomer diaphragm kit

253224

Overmolded EPDM diaphragm kit

15D990

Leak detector kit

Flapper Check Valve

Technical Specifications Meat and Poultry Maximum fluid working pressure Maximum free-flow delivery* Maximum suction lift Maximum size pumpable solids Typical sound level at 4.9 bar (70 psi) air @ 50 cpm Air pressure operating range Air inlet size Fluid inlet & outlet size (determined by part number) Weight Leaflet Instruction manual

8 bar (0.8 MPa - 120 psi) 568 l/min (150 gpm) 3.0 m (10 ft) wet 63.5 mm (2.5") 85 dBa 1.4 to 8.4 bar (0.14 to 0.84 MPa / 20-120 psi) 0.5" npt(f) Tri-clamp connections 65 kg (145 lb) 338067 310622

Maximum diaphragm operating temperature Santoprene Buna-N Fluoroelastomer EPDM

82.2ºC (180ºF) 82.2ºC (180ºF) 121ºC (250ºF) 135ºC (275ºF)

* Flow rates are with muffler and do not vary based on diaphragm material. Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type.

Air-Operated diaphragm pumps

SaniForce Meat and Poultry Pumps

Performance Charts MEATand AND Poultry POULTRYPerformance Performance Meat 120 (0.84, 8.4)

100 (0.7, 7)

80 (0.55, 5.5)

117

136

150 (4.2)

125 (3.5)

100 (2.8)

60 (0.41, 4.1)

75 (2.1) D

40 (0.28, 2.8)

50 (1.4)

20 (0.14, 1.4)

25 (0.7) 0

20 (75)

40 (151)

60 (227)

80 (302)

100 (378)

120 (454)

140 (531)

FLOW FLUIDFLUID FLOW gpm (lpm) gpm (l/min) AIR PRESSURE AIR PRESSURE A B C D

A = at 120 psi (8.4 bar, 0.84 MPa) = at 8.4 bar (0.84 MPa - 120 psi) at (0.7 100 MPa psi (7- bar, B 7 =bar = at 1000.7 psi)MPa) = at bar70(0.48 MPabar, - 70 = at psi (4.8 0.5psi) MPa) C 4.8 = at 2.8 bar (0.28 MPa - 40 psi) D = at 40 psi (2.8 bar, 0.3 MPa)

LEGEND LEGEND Air Consumption Air Consumption - - - - Fluid Flow Fluid Flow __________

Dimensions SaniForce 3150 Meat and Poultry Flapper Flapper Check Flapper CheckValve ValvePump Pumps

581.7 mm (22.9 in) 825.5 mm (32.5 in)

246.4 mm (9.7 in)

490.2 mm (19.3 in)

155

Air-Operated diaphragm pumps

160 (606)

3 AIR AIR CONSUMPTION CONSUMPTION scfm (mscfm /min)(m 3/min)

FLUID OUTLET PRESSURE psi (bar,psi MPA) FLUID OUTLET PRESSURE (MPa, bar)

CYCLES PER PER MINUTE CYCLES MINUTE

SaniForce Piston Pumps 6:1, 5:1 and 12:1 Ordering Information 6:1 Piston Pump Part Number 24E840 24G740

Pump Type Double Ball Double Ball

24E839 24E838 24E837 24E836

Double Ball Double Ball Double Ball Priming Piston

24G739

Priming Piston

24F942

Double Ball

Pump Length Drum Length Drum Length (Ram Package) Drum Length Stubby Stubby Stubby Stubby (Ram Package) Bin Length 123 cm (48.5")

Pump Inlet Type 3.6 cm (1.44") Slotted 15.2 cm (6") Clamp

Packings Buna, Nylon, Nitrile, & Polychloroprene Buna, Nylon, Nitrile, & Polychloroprene

Weight kg (lb) 16.7 (36.9) 17 (38)

3.6 cm (1.44") Slotted 6.3 cm (2.5") Clamp 6.3 cm (2.5") Clamp 5.8 cm (2.3") Priming Piston 15.2 cm (6") Clamp

PTFE Buna, UHMWPE & Polychloroprene PTFE Buna, Nylon, Nitrile & Polychloroprene

16.7 (36.9) 13.1 (28.9) 16.7 (36.9) 16.8 (33.8)

Buna, Nylon, Nitrile & Polychloroprene

16 (35)

1.44"(3.6 cm) Slotted

Buna, Nylon, Nitrile, & Polychloroprene

18 (39.7)

Pump Inlet Type 10.2 cm (4") Slotted

Packings Buna, PTFE, UHMWPE & FKM

Weight kg (lb) 54.1 (119)

10.2 cm (4") Slotted 15.2 cm (6") Clamp

Buna, PTFE, UHMWPE & FKM Buna, PTFE, UHMWPE & FKM

41.4 (91.3) 43 (95)

10.2 cm (4") Priming Piston 15,2 cm (6") Clamp

Buna, PTFE, UHMWPE, Polychloroprene, Nylon & FKM Buna, PTFE, UHMWPE, Polychloroprene, Nylon & FKM Buna, FKM, PTFE & UHMWPE

43.2 (95.3)

Buna, PTFE, Silicone, FKM & UHMWPE

41.1 (90.6)

Packings Acetal, PTFE, Nitrile and UHMWPE Acetal, PTFE, Nitrile and UHMWPE

Weight kg (lb) 55 (122) 55 (122)

5:1 Piston Pump Part Number 24F195

Pump Type Double Ball

24E833 24G742

Double Ball Double Ball

24E831

Priming Piston

24G741

Priming Piston

24F196

Double Ball

24F197

Double Ball

Pump Length Drum Length (Bung Mount) Stubby Drum Length (Ram Package) Drum Length Drum Length (Ram Package) Stubby Stubby (BES Mount)

90 degree elbow 6.3 cm (2.5") Clamp 10.2 cm (4") Clamp

45 (99) 42.2 (93.1)

12:1 Piston Pump Part Number 24F625 24F626*

Pump Type Priming Piston Priming Piston

Pump Length Stubby (Ram Package) Stubby (Ram Package)

Pump Inlet Type 15.2 cm (6") Clamp 15.2 cm (6") Clamp

*For use with viscous sticky material

Technical Specifications Fluid to air pressure ratio Maximum fluid pressure Maximum fluid flow at 60 cpm Air consumption at 60 cpm Volume per cycle Maximum operating temperature (fluid) Maximum operating temperature (air motor) Maximum size pumpable solids Maximum air input pressure Air inlet size Fluid outlet size Fluid inlet Leaflet Instruction manual

SaniForce 6:1 Piston Pump

SaniForce 5:1 Piston Pump

SaniForce 12:1 Piston Pump

6:1 41 bar (4.1 MPa - 600 psi) 15.1 l/min (4.0 gpm) 0.82 m3/min at 6.8 bar (29 cfm at 100 psi) 0.25 l (0.067 gal) 121ºC (250ºF) 49ºC (120ºF) 0.32 cm (0.13") 7 bar (0.7 MPa - 100 psi) 1/2 npsm(f) 3.8 cm (1-1/2") Tri-Clamp 3.8 cm (1-1/2") Tri-Clamp* 338591 3A0733

5:1 28 bar (2.8 MPa - 400 psi) 53 l/min (14 gpm) 1.97 m3/min at 5.5 bar (69 cfm at 80 psi) 0.87 l (0.23 gal) 60ºC (140ºF) 49ºC (120ºF) 0.64 cm (0.25 in) 5.5 bar (0.6 MPa - 80 psi) 1/2 npsm(f) 5.1 cm (2") Tri-Clamp 6.3 cm (2.5") Tri-Clamp (24F196 only) 338591 3A0734

12:1 83 bar (8.3 MPa - 1200 psi) 32 l/min (8.5 gpm) 3.3 m3/min at 6.9 bar (116 cfm at 100 psi) 0.54 l (0.14 gal) 71ºC (160ºF) 49ºC (120ºF) 0.64 cm (0.25") 7 bar (0.7 MPa - 100 psi) 1/2 npsm(f) 5.1 cm (2") Tri-Clamp 15.2 cm (6") Tri-Clamp 338591 3A0735

*Select sizes

SANIFORCE piston pumps

SaniForce Piston Pumps

Performance Charts PistonPump Pump Performance 6:16:1 Piston Performance

PistonPump Pump Performance 5:15:1 Piston Performance

CYCLES PER MINUTE

CYCLES PER MINUTE 60

600 (41, 4.1)

500 (34, 3.4)

400 (28, 2.8) 300 (21, 2.1)

0 35 (1.0)

450 (31, 3.1)

30 (.85)

400 (28, 2.8)

25 (.71)

350 (24, 2.4)

20 (.57) 15 (.42)

200 (14, 1.4)

10 (.28)

100 (7, 0.7)

5 (.14) 0

0.5 (1.9)

1 (3.8)

1.5 (5.7)

2 (7.6)

2.5 (9.5)

3 (11.4)

3.5 (13.2)

4 (15.1)

gpm tested in No.(l/min) 10 weight oil

= atbar 100 psi MPa (7 bar,- 120 0.7 MPa) A = Aat 8.4 (0.84 psi) at 70 (4.8- bar, B = Bat 7=bar (0.7psiMPa 1000.5 psi)MPa)

LEGEND LEGEND Air Consumption Air Consumption - - - - -

56 140 (3.96)

100 (2.83)

1000 (69, 7.0) B

600 (41, 4.1)

80 (2.27) 60 (1.70)

400 (28, 2.8)

40 (1.13)

200 (14, 1.4)

20 (.57) 0

1 (3.8)

2 (7.6)

3 (11.3)

4 (15.1)

5 (18.9)

6 (22.7)

7 (26.5)

FLOWgpm (lpm) FLUIDFLUID FLOW gpm tested in No.(l/min) 10 weight oil

AIR PRESSURE AIR PRESSURE A = Aat 8.4 (0.84 MPa 120MPa) psi) = atbar 100 psi (7 bar,- 0.7 B = Bat 7=bar (0.7psiMPa 1000.5 psi)MPa) at 70 (4.8- bar, C = at 4.8 bar (0.48 MPa - 70 psi) C = at 40 psi (2.8 bar, 0.3 MPa)

120 (3.40)

LEGEND LEGEND Air Consumption - - - - Air Consumption Fluid Flow __________ Fluid Flow

SANIFORCE piston pumps

8 (30.3)

AIR FLOW scfm (m /min)3 AIR FLOW scfm (m /min)

FLUID PRESSURE psi(bar, (bar, MPa) FLUID OUTLET PRESSURE psi MPA)

800 (55, 5.5)

70 (1.98) A

60 (1.70)

300 (21, 2.1)

B B

250 (17, 1.7)

50 (1.42) 40 (1.13)

200 (14, 1.4)

30 (0.85)

150 (10, 1.0)

20 (0.57)

100 (7, 0.7)

10 (0.28)

2 (7.6)

4 (15.1)

6 (22.7)

AIR PRESSURE AIR PRESSURE A = at 80 psi (5.5 bar, 0.5 MPa) A = at bar60(0.84 MPabar, - 120 = at psi (4.1 0.4 psi) MPa) B 8.4 B = at 7 bar (0.7 MPa - 100 psi) = at 40 psi (2.8 bar, 0.3psi) MPa) C C = at 4.8 bar (0.48 MPa - 70

1400 (97, 9.7) 1200 (83, 8.3)

8 (30.3)

10 (37.8)

12 (45.4)

gpm tested in No.(l/min) 10 weight oil

CYCLESPER PER MINUTE CYCLES MINUTE

FLOWgpm (lpm) FLUIDFLUID FLOW

12:1 Piston Performance 12:1 Piston Pump Pump Performance 10

80 (2.27)

Fluid Flow Fluid Flow __________

C = Cat 4.8 MPabar, - 70 = atbar 40(0.48 psi (2.8 0.3psi) MPa) D = at 2.8 bar (0.28 MPa - 40 psi) E = at 1.4 bar (0.14 MPa - 20 psi)

50 (3.4, 0.3)

FLOWgpm (lpm) FLUIDFLUID FLOW AIR PRESSURE AIR PRESSURE

LEGEND LEGEND Air Consumption Air Consumption - - - - Fluid Flow Fluid Flow __________

14 (53)

3 AIR scfm FLOW(m scfm (m3/min) AIR FLOW /min)

FLUID FLUID PRESSURE psi (bar, psi MPa) OUTLET PRESSURE (bar, MPA)

FLUID PRESSURE psi(bar, (bar,MPA) MPa) FLUID OUTLET PRESSURE psi

700 (48, 4.8)

AIR FLOW scfm (m /min) AIR FLOW scfm (m 3/min)

SaniForce Piston Pumps

Dimensions SaniForce 6:1

SaniForce 5:1

Stubby Length Stubby Length

Drum and and Bin BinLength Length

Stubby StubbyLength Length

DrumLength and Bin Length Drum

A B C

B C

Model 24G742

Model Model

24E836 24E836 24E837 24E837 24E838 24E838 24G739 24G739 24G740 24E839 24G740 24E840 24E839 24F942 24E840 24F942

PumpStyle Style Pump Stubby Stubby

C A A B B C D (OD)D (OD) (inch) in (cm) cm (inch) in (cm) cm (inch) in (cm) cm (inch) incm (cm) 99.5 (39.2) 50 (19.5) 38 (15.1) 5.4 (2.1) 39.2 (99.5) 19.5 (50) 15.1 (38) 2.1 (5.4)

24E833 24F196 24F197 24G741 24E831

Drum Drum Length Length Bin Length Bin Length

60.5 (153.7) 153.7 (60.5)41 (104) 104 (41) 36.4 (92) 92 (36.4) 2.1 (5.4) 5.4 (2.1) 73 (185.4)

24F195

A B C A B C Pump Style cm (inch) cm (inch) cm (inch) Model Pump Style in (cm) in (cm) in (cm) Double Ball, Stubby 131 (51.5) 66 (25.9) 52 (20.4) 24G742 Double Ball, Stubby 51.5 (131) 25.9 (66) 20.4 (52) 24E833 Double Ball, Stubby with inlet 143 (56.3) 78 (30.7) 64 (25.2) 24F196 Double Ball, Stubby with inlet 56.3 (143) 30.7 (78) 25.2 (64) Double Ball, Bin Length 128 (50.4) 63 (24.8) 49 (19.3) 24F197 Double Ball, Bin Length 50.4 (128) 24.8 (63) 19.3 (49) Priming Piston, Drum Length 145 (57.0) 80 (31.3) 66 (25.9) 24G741 Priming Piston, Drum Length Priming Piston, Drum Length 57.0 (145) 31.3 (80) 25.9 (66) 24E831 Priming Piston, Drum Length Double Ball, Drum Length 172 (67.9) 107 (42.3) 93 (36.8) 24F195 Double Ball, Drum Length 67.9 (172) 42.3 (107) 36.8 (93)

53.5 (135.9) 48.9 (124.2) 2.1 (5.4)

185.4 (73)

135.9 (53.5)

124.2 (48.9)

5.4 (2.1)

SaniForce 12:1

120.7 cm (47.5 in)

41 cm (16.1 in)

54 cm (21.1 in)

SANIFORCE piston pumps

SaniForce Drum Unloaders Pump Packages Ordering Information SaniForce 6:1 Drum Unloader Part Number 24D776 24D780 24D782 24D788 24D792 24D794

Pump Number 24G739 24G739 24G739 24G740 24G740 24G740

Pump Type Priming Piston Priming Piston Priming Piston Double Ball Double Ball Double Ball

Ram Material SST CS* SST SST CS* SST

Ram Plate No. 16G240 16G240 16G240 16G240 16G240 16G240

Inflatable Seal No. 16G242 16G242 16G242 16G242 16G242 16G242

Control Type Exposed Exposed Enclosed SST Exposed Exposed Enclosed SST

Weight kg (lb) 160 (353) 169 (372) 166 (367) 161 (356) 170 (375) 168 (370)

Ram Material SST CS* SST SST CS* SST

Ram Plate No. 16G240 16G240 16G240 16G240 16G240 16G240

Inflatable Seal No. 16G242 16G242 16G242 16G242 16G242 16G242

Control Type Exposed Exposed Enclosed SST Exposed Exposed Enclosed SST

Weight kg (lb) 187 (413) 196 (433) 194 (428) 189 (417) 198 (437) 196 (432)

Ram Material SST CS* SST SST CS* SST

Ram Plate No. 16G240 16G240 16G240 16G240 16G240 16G240

Inflatable Seal No. 16G242 16G242 16G242 16G242 16G242 16G242

Control Type Exposed Exposed Enclosed SST Exposed Exposed Enclosed SST

Weight kg (lb) 200 (440) 208 (459) 206 (454) 200 (440) 208 (459) 206 (454)

SaniForce 5:1 Drum Unloader Part Number 24D708 24D712 24D714 24D720 24D724 24D726

Pump Number 24G741 24G741 24G741 24G742 24G742 24G742

Pump Type Priming Piston Priming Piston Priming Piston Double Ball Double Ball Double Ball

SaniForce 12:1 Drum Unloader Part Number 24D647 24D651 24D653 24F188** 24F189** 24F190**

Pump Number 24F625 24F625 24F625 24F626 24F626 24F626

Pump Type Priming Piston Priming Piston Priming Piston Priming Piston Priming Piston Priming Piston

*CS = Painted carbon steel. **For use with viscous material.

Technical Specifications Drum Unloaders Max fluid pressure Max Flow at 60 cpm Max Flow at 100 cpm Viscosity range of packings Max inlet air pressure Air inlet size (enclosed, exposed controls) Evacuation efficiency Leaflet Instruction manual

6:1 Double Ball Pump

6:1 Priming Piston

5:1 Double Ball Pump

5:1 Priming Piston

12:1 Priming Piston

3150 High Sanitation

2150 High Sanitation

41 bar (4.1 MPa - 600 psi) 15.1 l/min (4.0 gpm) – 25,000100,000 cps 7 bar (0.7 MPa - 100 psi) 1/2 npt(f), 3/4 npt(f) 99% 338590 3A0591

41 bar (4.1 MPa - 600 psi) 15.1 l/min (4.0 gpm) – 60,000500,000 cps 7 bar (0.7 MPa - 100 psi) 1/2 npt(f), 3/4 npt(f) 99% 338590 3A0591

28 bar (2.8 MPa - 400 psi) 53 l/min (14 gpm) – 25,000100,000 cps 5.5 bar (0.6 MPa - 80 psi) 1/2 npt(f), 3/4 npt(f) 99% 338590 3A0591

28 bar (2.8 MPa - 400 psi) 53 l/min (14 gpm) – 60,000500,000 cps 5.5 bar (0.6 MPa, 80 psi) 1/2 npt(f), 3/4 npt(f) 99% 338590 3A0591

83 bar (8.3 MPa - 1200 psi) 32 l/min (8.5 gpm) – 60,000500,000 cps 7 bar (0.7 MPa, 100 psi) 1/2 npt(f), 3/4 npt(f) 99% 338590 3A0591

8.3 bar (0.83 MPa - 120 psi) 227 l/min (60 gpm) 378 l/min (100 gpm) 25,000100,000 cps 8.3 bar (0.8 MPa, 120 psi) 1/2 npt(f), 3/4 npt(f) 99% 338590 3A0591

* Flow rates based on full displacement of lower and S.G. = 1

Pump Packages

SaniForce Drum Unloaders

Ordering Information SaniForce 3150 HS Drum Unloader Part Number 24D922 24D926 24D928 24D932

Pump Number 24C124 24C124 24C124 248273

Pump Type Ball Ball Ball Ball

Ram Material SST CS* SST CS*

Ram Plate No. 16G241 16G241 16G241 16G241

Inflatable Seal No. 16G242 16G242 16G242 16G242

Control Type Exposed Exposed Enclosed SST Exposed

Weight kg (lb) 194 (428) 201 (443) 200 (442) 201 (443)

Diaphragm Material Overmolded EPDM, 3A Overmolded EPDM, 3A Overmolded EPDM, 3A Santoprene

Ball Material PTFE PTFE PTFE Santoprene

24D936

248273

Ball

SST

16G241

16G242

Enclosed SST

200 (442)

Santoprene

24D940

248273

Ball

SST

16G241

16G242

Exposed

194 (428)

Santoprene

24D944

248274

Flapper

SST

16G241

16G242

Exposed

194 (428)

Santoprene

–

24D948

248274

Flapper

CS*

16G241

16G242

Exposed

201 (443)

Santoprene

–

24D952

248274

Flapper

SST

16G241

16G242

Enclosed SST

200 (442)

Santoprene

–

Ram Plate No. 16G241 16G241 16G241 16G241

Inflatable Seal No. 16G242 16G242 16G242 16G242

Control Type Exposed Exposed Enclosed SST Exposed

Weight kg (lb) 204 (450) 210 (464) 210 (464) 204 (450)

Diaphragm Material Overmolded PTFE Overmolded PTFE Overmolded PTFE Santoprene

SaniForce 2150 Drum Unloader Part Number 24G542 24F191 24G543 24F192

Pump Number 24G743 24G743 24G743 24G744

Pump Type Ball Ball Ball Ball

Ram Material SST CS* SST SST

Ball Material PTFE PTFE PTFE Weighted polychloroprene

24F193

24G744

Ball

CS*

16G241

16G242

Exposed

210 (464)

Santoprene

Weighted polychloroprene

24F194

24G744

Ball

SST

16G241

16G242

Enclosed SST

210 (464)

Santoprene

Weighted polychloroprene

*CS = Painted carbon steel.

Dimensions SaniForce Drum Unloader

ft (2.75 2.759 m (9 ft)m) whenfully fully raised raised when

SaniForce 3150 HS Drum Unloader

SaniForce 2150 Drum Unloader

Four (14 mm) in) Four 140.562" mm (0.562 mounting holes mounting holes

965 mm 1067 mm (38 in) (42 in)

534 mm (21 in) 635 mm (25 in)

Pump Packages

SaniForce Bin Evacuation Systems Pump Packages Ordering Information SaniForce BES BES Part Number

Max. Working Fluid Pressure per pump bar (MPa, psi)

Pump Part No.

Pump Quantity

Pump Description

Control Type

BIN Manuf

BESA4C

28 (2.8 - 400)

24G742

SaniForce 5:1

Manual

Pallecon

BESA7A

28 (2.8 - 400)

24G742

SaniForce 5:1

Electronic

Plywood

BESA7C

28 (2.8 - 400)

24G742

SaniForce 5:1

Manual

Plywood

BESA7F

28 (2.8 - 400)

24G742

SaniForce 5:1

Electronic

Plywood

BESB7B

28 (2.8 - 400)

24G742

SaniForce 5:1

Electronic

Plywood

BESB7D

28 (2.8 - 400)

24G742

SaniForce 5:1

Manual

Plywood

BESE1A

83 (8.3 - 1200)

24F625

SaniForce 12:1

Electronic

Arena

BESE1C

83 (8.3 - 1200)

24F625

SaniForce 12:1

Manual

Arena

BESE5C

83 (8.3 - 1200)

24F625

SaniForce 12:1

Manual

Pallecon

BESF6B

83 (8.3 - 1200)

24F625

SaniForce 12:1

Electronic

Arena

BESF6D

83 (8.3 - 1200)

24F625

SaniForce 12:1

Manual

Arena

BESF9B

83 (8.3 - 1200)

24F625

SaniForce 12:1

Electronic

TNT

BESF9D

83 (8.3 - 1200)

24F625

SaniForce 12:1

Manual

TNT

Note: Systems can be special ordered for bin types other than plywood, arena and pallecon. Contact your sales rep for additional information.

Technical Specifications SaniForce BES Part No

BESAxx

BESExx

BESFxx

Max. working fluid pressure

28 bar (2.8 MPa - 400 psi)

BESBxx

83 bar (8.3 MPa - 1200 psi)

Compressed air requirement

5.5-7 bar (0.55-0.7 MPa - 80-100 psi)

Max. inlet air pressure

5.5 bar (0.55 MPa - 80 psi)

7 bar (0.7 MPa - 100 psi)

Air inlet size

3/4 in npt(f)

Air inlet pump

1/2 in npt(f)

Pneumatic control panel specifications

Fluid displacement (each pump)

0.87 l/cycle (0.23 gal/cycle)

0.52 l/cycle (0.14 gal/cycle)

Max. flow @ 60 cpm*

106 l/min (28 gpm)

64 l/min (17 gpm)

128 l/min (34 gpm)

Pressure ratio

5:1

12:1

Air consumption (each pump) at 2.8 bar (0.28 MPa - 40 psi)

~0.085 m /min per 3.7 l/min (~2.95 scfm per gpm)

~ 0.21 m /min per 3.7 l/min (~7.5 scfm per gpm)

~ 0.21 m3/min per 3.7 l/min (~7.5 scfm per gpm)

Pump outlet

2 in tri-clamp

Communication

RS232 Serial

Electrical requirements

110 VAC (60 Hz), 15A

Overall dimensions m (inch)

1.72 W x 1.52 D x 3.0 H (69 W x 60 D x 118.8 H)

Evacuation efficiency

2 pumps: 98% | 4 pumps: 99%

N/A

Leaflet

338589

Instruction manual

311163

212 l/min (56 gpm)

* Flow rates based on full displacement of lower and S.G. = 1 Note: Graco’s BES packages are available for a variety of manufacturers’ bins and custom systems can be built upon request. Contact Graco for more information.

Pump Packages

SaniForce Bin Evacuation Systems Ordering Information SaniForce 3150 BES Part Number

Type

Bin Manuf.

Control Type

Outlet Size

Diaphragm/Ball Material**

BES3P3

Ball

Plywood

Manual

3" (76 mm)

Santoprene/ PTFE

BES3P1

Ball

Plywood

Electronic

3" (76 mm)

Santoprene/ PTFE

BES4P3

Flapper

Plywood

Manual

3" (76 mm)

Santoprene/ N/A

BES8B3

Ball

Pallecon

Manual

3" (76 mm)

Overmolded EPDM, 3A

BES3A1

Ball

Arena

Electronic

3" (76 mm)

Santoprene/ PTFE

BES4A1

Flapper

Arena

Electronic

3" (76 mm)

Santoprene/ N/A

Note: Contact marketing for ordering information on non-plywood bins. **3A Approved EPDM diaphragm is available for heavy duty applications.

Technical Specifications SaniForce 3150 BES Part No

BES3xx

Max. working fluid pressure

8.4 bar (0.84 MPa, 120 psi)

BES4xx

Compressed air requirement

5.5-8.4 bar (0.55-0.84 MPa - 80-120 psi)

Pneumatic control panel specifications Max. inlet air pressure

8.4 bar (0.84 MPa - 120 psi)

Air inlet size

3/4" npt(f)

Air inlet pump

1/2" npt(f)

Fluid displacement (each pump)

3.89 l/cycle (1.03 gal/cycle)

Max. flow @ 145 cpm*

1,135 l/min (300 gpm)

Pressure ratio

1:1

Air consumption (each pump) at 4.8 bar (0.48 MPa - 70 psi)

~ 0.02 m3/min per 3.7 l/min (~0.8 scfm per gpm)

Pump outlet

3 in tri-clamp

Max. suction lift

5.5 m (18 ft) wet

Max. diaphragm operating temperature (Santoprene, 3A Approved EPDM)

82.2ºC (180ºF), 135ºC (275ºF)

Typical sound level at 4.9 bar (70 psi) air @ 50 cpm

85 dBa

Weight

1,360 kg (3,000 lb)

Leaflet

338589

Instruction manual

311163

3.0 m (10 ft) wet

* Flow rates are with muffler and slightly vary based on diaphragm material. Displacement per cycle may vary based on suction condition, discharge head, air pressure and fluid type.

Pump Packages

SaniForce Bin Evacuation Systems

Dimensions SaniForce BES Front View Top View

4 holes per foot

Front View

Top View

4 holes per foot

Pump Packages

Hydra-Clean Pressure Washers High Sanitation Cleaning Packages Ordering Information Wall Mount Hydra-Clean Package Package Order No.

247550

247552

247554

258665

Air Motor Part No.

N34DN0

N65DN0

N65DNO

Pump Lower Part No.

247599

241648

687055

24B923

Pump Construction

SST

Standard Seal Repair Kit

247881

222880

See manual 311825

24C162

Standard Seal Construction

PTFE/ CF-PTFE

UHMWPE/ CF-PTFE

Optional Seal Repair Kits

207581

222875

222845

237713

Optional Seal Construction

PTFE

UHMWPE/PTFE

Leaflet

338026

Instruction Manual

312585

Cart Mount Hydra-Clean Package Package Order No.

247549

247551

247553

258664

Air Motor Part No.

N34DN0

N65DN0

N65DNO

Pump Lower Part No.

247599

241648

687055

24B923

Pump Construction

SST

Standard Seal Repair Kit

247881

222880

See manual 311825

24C162

Standard Seal Construction

PTFE/ CF-PTFE

UHMWPE/ CF-PTFE

Optional Seal Repair Kits

207581

222875

222845

237713

Optional Seal Construction

PTFE

UHMWPE/PTFE

Leaflet

338026

Instruction Manual

312585

Drum Mount Hydra-Clean Package Package Order No.

206515

Air Motor Part No.

207352

Pump Lower Part No.

224344

Pump Construction

SST

Standard Seal Repair Kit

224402

Standard Seal Construction

UHMWPE/Polychloroprene

Optional Seal Construction

UHMWPE/PTFE

Instruction Manual

306817

High Sanitation Cleaning Packages

Hydra-Clean Pressure Washers

Accessories Part Number

Part Number

Description

Hoses

Guns and Wands 247879

Standard brass/SST gun/wand

214959

1" x 1.8 m (6 ft) inlet hose

15T283

Standard replacement brass/SST spray gun

247878

3/8 in x 15 m (50 ft) outlet hose: 310 bar (4500 psi)

15T282

Optional replacement SST spray gun

Other

15T279

32" SST wand

15T284

60 mesh inlet strainer with 1" npt(f) connection

15T280

10" SST wand

191635

10 mesh inlet strainer with 1" npt(f) connection

247880

Gun SST quick disconnect connections

247622

Gun and suction tube holder

Stainless Steel Tips Part Number

Tip Number

Orifice Size

Fan Width Angle at 3 bar (0.03 MPa - 40 psi)

Capacity at 68.9 bar (6.89 MPa - 1000 psi)

805534

40020

0.51 mm (0.020")

40ยบ

3.78 l/min (1.00 gpm)

805538*

40030

0.76 mm (0.030")

40ยบ

5.68 l/min (1.50 gpm)

805542

40035

0.89 mm (0.035")

40ยบ

6.62 l/min (1.75 gpm)

805549*

25045

1.14 mm (0.045")

25ยบ

8.52 l/min (2.25 gpm)

805561

25060

1.52 mm (0.060")

25ยบ

11.36 l/min (3.00 gpm)

805562

40060

1.52 mm (0.060")

40ยบ

11.36 l/min (3.00 gpm)

805566*

40065

1.65 mm (0.065")

40ยบ

12.30 l/min (3.25 gpm)

805569

25070

1.78 mm (0.070")

25ยบ

13.25 l/min (3.50 gpm)

805458

40075

1.91 mm (0.075")

40ยบ

14.20 l/min (3.75 gpm)

805575*

00080

2.03 mm (0.080")

0ยบ

15.14 l/min (4.00 gpm)

805587

00100

2.54 mm (0.100")

0ยบ

18.93 l/min (5.00 gpm)

*Tip included with pump packages Other orifice sizes and fan widths available from Graco, contact a sales representative for more information.

Technical Specifications Part Number

Pump Package

Max. Working Pressure bar (MPa - psi)

Max. Air Input Pressure bar (MPa - psi)

Fluid Flow at 60 cpm l/min (gpm)

Vol. per Cycle cc (oz)

Air Inlet Size

Fluid Inlet Size

Fluid Outlet Size*

Leaflet

Manual

247549 247550 247551 247552 247553 247554 258664 258665 206515

12:1 Cart Mount 12:1 Wall Mount 23:1 Cart Mount 23:1 Wall Mount 30:1 Cart Mount 30:1 Wall Mount 45:1 Cart Mount 45:1 Wall Mount 10:1 Drum Mount

86 (8.6 - 1250) 86 (8.6 - 1250) 157 (15.7 - 2275) 157 (15.7 - 2275) 211 (21.1 - 3065) 211 (21.1 - 3065) 310 (31.0 - 4500) 310 (31.0 - 4500) 125 (12.5 - 1800)

7 (0.7 - 100) 7 (0.7 - 100) 7 (0.7 - 100) 7 (0.7 - 100) 7 (0.7 - 100) 7 (0.7 - 100) 7 (0.7 - 100) 7 (0.7 - 100) 12.5 (1.2 - 180)

33.0 (8.7) 33.0 (8.7) 34.7 (9.2) 34.7 (9.2) 25.9 (6.8) 25.9 (6.8) 17.4 (4.6) 17.4 (4.6) 11.4 (3.0)

550 (18.6) 550 (18.6) 580 (19.6) 580 (19.6) 430 (14.5) 430 (14.5) 290 (9.8) 290 (9.8) 189 (6.4)

3/4 npt(f) 3/4 npt(f) 3/4 npt(f) 3/4 npt(f) 3/4 npt(f) 3/4 npt(f) 3/4 npt(f) 3/4 npt(f) 1/2 npt(f)

1" 1" 1" 1" 1" 1" 1" 1" 1/2"

3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/4"

338026 338026 338026 338026 338026 338026 338026 338026 โ

312585 312585 312585 312585 312585 312585 312585 312585 306817

*Includes two outlet ports per unit. Part number 206515 has only one outlet port.

High Sanitation Cleaning Packages

Hydra-Clean Pressure Washers

Dimensions Hydra-Clean Wall Mount Package 247550 Wall Mount Package 247550

Cart Mount 247549 Cart Mount Package Package 247549

451 mm (17.1 in)

1125 mm (44.3 in)

1270 mm (50.0 in)

782 mm (30.8 in)

434 mm (17.1 in) 434 mm (17.1 in) 142 mm (5.6 in)

to manual for additional package dimensions Refer to manualRefer 312585 for 312585 additional package information

653 mm (25.7 in)

High Sanitation Cleaning Packages

Overmolded Diaphragms Accessories Ordering Information PTFE/EDPM Heavy-Duty Overmolded Diaphragms Pump Part No.

Pump Size

Inlet/Outlet Size

Air Motor

Fluid Section

Seats

Balls

O-Rings

FD1113 FD1213 FD2113 FD2213 FD3113 FD3213

1" 1" 1.5" 1.5" 2" 2"

1.5" 1.5" 2" 2" 2.5" 2.5"

SST SST SST SST SST SST

PTFE PTFE PTFE PTFE PTFE PTFE

PTFE EPDM PTFE EPDM PTFE EPDM

High Sanitation PTFE/EDPM Heavy-Duty Overmolded Diaphragms Pump Part No.

Pump Size

1590 High Sanitation Pump SABA13* 1.5" SBBA13 1.5" 3150 High Sanitation Pump SA13A1 2" SA23A1 2" SA33A1 2" SA3361 2" SA53A1 2" SA43A1 2"

Inlet/Outlet Size

Air Motor

Fluid Section

Seats

Balls

2" 2"

SST SST

PTFE PTFE

1.5" 2" 3" 3" 3" x 2" 4"

SST SST SST SST SST SST

PTFE PTFE PTFE Santoprene PTFE PTFE

*Includes leak detector

High Sanitation and Industrial Repair Kits*

SaniForce 1040, 1590 & 2150 Pump Repair Kits

Part No.

Description

Part No.

Description

253626

For 1" pump size, diaphragm repair kit

FK1113

For 1" pump size, with PTFE o-rings

253627

For 1.5" pump size, diaphragm repair kit

FK1213

For 1" pump size, with EPDM o-rings

253628

For 2" pump size, diaphragm repair kit

FK2113

For 1.5" pump size, with PTFE o-rings

FK2213

For 1.5" pump size, with EPDM o-rings

FK3113

For 2" pump size, with PTFE o-rings

FK3213

For 2" pump size, with EPDM o-rings

*To replace PTFE overmolded diaphragms

High Sanitation and Industrial Upgrade Kits* Part No.

Description

289224

Upgrade kit for 1" pump

289225

Upgrade kit for 1.5" pump

289226

Upgrade kit for 2" pump

*Includes new airside diaphragm plate for replacement of standard bolt-through diaphragm.

Technical Specifications Overmolded Diaphragms Material/Construction on wetted side Material/Construction on air side Temperature range Flex life Safety

Accessories

FDA-Compliant PTFE FDA-Compliant EPDM -10ยบC to 82ยบC (14ยบF to 180ยบF) 5x original Graco 2-piece PTFE diaphragm sets Complies to FDA21CFR 177.1550 (PTFE) and FDA21CFR 177.2600 (EPDM)

Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance or structures, accessories, equipment or materials not supplied by Graco. This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation. THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale. GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties. In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

Equipment Misuse Hazard General Misuse: Any misuse of Graco equipment or accessories, such as over-pressurizing, modifying parts, using incompatible chemicals and fluids, or using worn or damaged parts, can cause them to rupture. Misuse of equipment can result in fluid injection, splashing in the eyes or on the skin, or other serious bodily injury, or fire, explosion or property damage. NEVER alter or modify any part of Graco equipment; doing so could cause the product to malfunction. CHECK all equipment regularly and repair or replace worn or damaged parts immediately. Always wear protective eye wear, gloves, clothing and respirator as recommended by fluid and solvent manufacturers. System Pressure: Be sure that all equipment and accessories used are rated to withstand the applicable MAXIMUM WORKING PRESSURE. DO NOT exceed the maximum working pressure of any component or accessory used in a system. Fluid and Solvent Compatibility: All chemicals used in a Graco sprayer must be compatible with wetted parts. Consult your chemical supplier to ensure compatibility. Do not use 1:1:1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in this equipment, which contains aluminium and/or zinc parts. Such use could result in a serious chemical reaction, with the possibility of explosion, which could cause death, serious bodily injury and/or substantial property damage.

ABOUT GRACO

Founded in 1926, Graco is a world leader in fluid handling systems and components. Graco products move, measure, control, dispense and apply a wide range of fluids and viscous materials used in vehicle lubrication, commercial and industrial settings. The company’s success is based on its unwavering commitment to technical excellence, world-class manufacturing and unparalleled customer service. Working closely with qualified distributors, Graco offers systems, products and technology that set the quality standard in a wide range of fluid handling solutions. Graco provides equipment for spray finishing, protective coating, paint circulation, lubrication, and dispensing sealants and adhesives, along with power application equipment for the contractor industry. Graco’s ongoing investment in fluid management and control will continue to provide innovative solutions to a diverse global market.

GRACO LOCATIONS

MAILING ADDRESS

P.O. Box 1441 Minneapolis, MN 55440-1441 Tel: 612-623-6000 Fax: 612-623-6777

AMERICAS

ASIA PACIFIC Graco Australia Pty Ltd. Suite 17, 2 Enterprise Drive Bundoora, Victoria 3083 Australia Tel: 61 3 9468 8500 Fax: 61 3 9468 8599

Graco Hong Kong Ltd. India Liaison Office Room 432, Augusta Point Regus Business Centre 53 Golf Course Road Gurgaon, Haryana India 122001 Tel: 91 124 435 4208 Fax: 91 124 435 4001

CHINA

JAPAN

AUSTRALIA

MINNESOTA

Worldwide Headquarters Graco Inc. 88 -11th Avenue N.E. Minneapolis, MN 55413

EUROPE BELGIUM

European Headquarters Graco N.V. Industrieterrein-Oude Bunders Slakweidestraat 31 3630 Maasmechelen, Belgium Tel: 32 89 770 700 Fax: 32 89 770 777

INDIA

Graco Hong Kong Ltd. Shanghai Representative Office Room 118 1st Floor No.2 Xin Yuan Building No.509 Cao Bao Road Shanghai, 200233 The People’s Republic of China Tel: 86 21 649 50088 Fax: 86 21 649 50077

Graco K.K. 1-27-12 Hayabuchi Tsuzuki-ku Yokohama City, Japan 2240025 Tel: 81 45 593 7300 Fax: 81 45 593 7301

KOREA

Graco Korea Inc. Shinhan Bank Building 4th Floor #1599 Gwanyang-Dong, Dongan-Ku, Anyang-si, Korea 431-060 Tel: 82 31 476 9400 Fax: 82 31 476 9801

All written and visual data contained in this document are based on the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.

Graco is certified ISO 9001.

Europe +32 89 770 700 Fax +32 89 770 777 www.graco.COM ©2010 Graco Inc. 344796E Rev. B 01/11 Printed in Europe. All other brand names or marks are used for identification purposes and are trademarks of their respective owners.