RESIN SOCKETING WARNING AND SAFETY INFORMATION

NOTE:

• Times are approximate. The temperature of the resin, socket and wire rope can affect these times. The times above are based on the temperature of the resin at the time of mixing.

• Thorough mixing is required to achieve appropriate times listed in the table to the right.

• Approximate time to gel begins once resin has been mixed. • Approximate time to cure begins once resin has gelled.

Warnings

• Inspect inside of socket bowl to determine if socket has grooves. If grooves are present, fill grooves with socketing putty.

• If using wire for seizing, only use soft annealed iron wire.

• Socket Lock resin must be gelled and cured before assembly can be used.

• Socket Lock is not to be used with stainless steel rope in a salt water environment.

• Never use oversized sockets for wire rope unless you consult the socket and wire rope manufacturer.

• Never use Socket Lock beyond the expiration date.

• Never heat socket prior to pouring resin in an effort to accelerate the curing of the resin as it may cause the resin to prematurely gel prior to reaching the bottom of the socket bowl. Doing this could cause the assembly to fail.

• Caution: Exposure to some strong chemicals may affect the cured polymer (hardened resin mixture) in a way that could weaken the assembly. Please contact the manufacturer if this has occurred.

Safery Information

• When handling the resin or hardener, goggles and protective clothing are recommended. Impervious gloves are recommended.

• Always work in a ventilated area.

• Avoid skin or eye contact. Wash skin with soap and water and remove contaminated clothing. If contact with eyes, flush with clean water for at least 15 minutes. If irritation persists, seek medical attention.

• Avoid ingestion. If ingestion occurs, DO NOT induce vomiting. Drink milk or water to dilute and call for medical attention.

• Avoid inhaling vapors. If excessive vapors are inhaled, move to a fresh air area. If breathing has stopped or is labored seek medical attention.

• Never aim an open flame at Socket Lock. Keep away from heat. Resin is a flammable liquid.

• Whenever using chemicals, always reference the MSDS sheet for safety and handling guidelines.

VISIT socket-locket.com FOR FULL INFORMATION BROCHURE!

NOTE: Socket volumes are approximate and may vary according to manufacturer

SOCKET - SWAGE, CLOSED, FORGED

• Swage sockets properly applied have an efficiency rating of 100% based on catalog strength of wire rope.

• Swage sockets are recommended for use with 6x19, 6x37, IWRC wire rope, and galvanized bridge rope.

• Swage sockets are not recommended for use on fiber core or lang lay wire rope.

SOCKET - SWAGE, OPEN, FORGED

• Swage sockets properly applied have and efficiency rating of 100% based on catalog strength of wire rope.

• Swage sockets are recommended for use with 6x19, 6x37, IWRC wire rope, and galvanized bridge rope.

• Swage sockets are not recommended for use on fiber core or lang lay wire rope.

SOCKET - WEDGE, OPEN

WEDGE SOCKET WARNINGS AND USE, SEE NEXT PAGE

Wedge Socket Warnings And Use

• Always inspect socket, wedge and pin before using.

• Do not use any part that is showing cracks, do not repair by welding.

• Do not modify or substitute any parts.

• Inspect assemblies before use.

• Do not mix and match wedges or pins between sizes.

• Always select the wedge and socket for the wire rope size.

• Use only with standard 6 to 8 strand wire rope of designated size, for intermediate size rope, use next larger size socket.

• Welding of tail on standard wire rope is not recommended, the tail length of the dead end should be a minimum of 6 rope diameters but not less than 6".

• Secure dead end section of rope. DO NOT ATTACH DEAD END TO LIVE END.

• Use a hammer to seat the wedge and rope as deep into socket as possible before applying first load.

• To use with rotation resistant wire rope, ensure that the dead end is welded or seized before inserting the wire rope into the wedge socket to prevent core slippage or loss of rope lay. The tail length of the dead end should be a minimum of 20 rope diameters but not less than 6".

• Efficiency rating of the wedge socket termination is based on the catalog breaking strength of wire rope. The efficiency of properly assembled wedge socket is 80%.

• LOADS MAY SLIP OR FALL IF THE WEDGE SOCKET IS NOT PROPERLY INSTALLED.

• A FALLING LOAD CAN SERIOUSLY INJURE OR KILL.

• READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING THE WEDGE SOCKET.

• DO NOT SIDE LOAD THE WEDGE SOCKET.

• DO NOT INTERCHANGE WEDGE SOCKET, WEDGE OR PIN WITH OTHER MANUFACTURES SOCKET, WEDGE OR PIN.

• APPLY FIRST LOAD TO FULLY SEAT THE WEDGE AND WIRE ROPE IN THE SOCKET. THIS LOAD SHOULD BE OF EQUAL OR GREATER WEIGHT THAN LOADS EXPECTED IN USE.

• DO NOT INTERCHANGE WEDGE BETWEEN SIZES.

LOADBINDER - LEVER

Ball & Socket swivel joint at hook assembly permits a straight line pull

Before use, oil ball & socket for longer life

• Material: Forged Steel, Quenched & Tempered

• Standard: EN 12195-3

• Finish: Painted Yellow

• Design Factor: 3.5:1

• Identification: Trademark, Size/WLL, Batch Code

LOADBINDER - LEVER, BX

BX-600 / BX-800

Load Binder Lever with Kickback Resistance

Ball & Socket swivel joing at hook assembly permits a straight line pull.

Before use, oil ball & socket for longer life.

• Material: Forged Steel, Quenched & Tempered

• Standard: EN 12195-3

• Finish: Painted Yellow

• Design Factor: 3.5:1

• Identification: Trademark, Size/WLL, Batch Code

LOADBINDER - RATCHET, HS

Matches the Working Load Limit of Grade 100 Chain for both sizes

• Material: Forged Steel, Quenched & Tempered, Gr 100

• Standard: EN 12195-3, WSTDA-T-6

• Finish: Powder Coated Yellow & Blue

• Design Factor: 3:1

• Identification: Trademark, Size/WLL, Batch Code

• Meets or exceeds DOT and CVSA Cargo Securement Tie-Down Guideline

LOADBINDER - RATCHET

• Material: Forged Alloy Steel, Quenched & Tempered

• Standard: EN 12195-3, WSTDA-T-6

• Finish: Painted Yellow

• Design Factor: 3.5:1

• Identification: Trademark, Size/WLL, Batch Code

Failure to use binders properly may result in serious injury or death. DO NOT operate load binder while standing on the load. Keep yourself out of the path of the moving handle and loose chain lying on the handle. You must be familiar with regulations regarding size and number of chain systems required for securing loads. Always consider the safety of nearby workers as well as yourself when using load binder. While under tension, load binder must not bear against an object, as this will cause side load. Do not use handle extender. Do not attempt to open or close the binder with more than one person.

LOADBINDER - RATCHET, T-HANDLE

• Material: Forged Steel, Quenched & Tempered

• Standard: EN 12195-3, WSTDA-T-6

• Finish: Painted Yellow & Blue

• Design Factor: 3:1

• Identification: Trademark, Size/WLL

TIE DOWN CARGO STRAP - CHAIN ASSEMBLY

• Material: Grade 70, Carbon Steel, Polyester

• Standard: EN 12195-2,3,WSTDA-T-1

• Finish: UV Protection, Yellow Chromate

• Design Factor: 3:1

• Identification: Trademark, Size/WLL

Compliant with National Safety Code Standard (NSC) 10 Part 1. Division 3, Section 11 (4)

“On and after January 1, 2011 a person shall not use a tie down or a component of a tie downtown secure cargo to a vehicle unless it is marked by the manufacturer with respect to its working load limit."

WINCH - TRUCK, #5820

• Designed for use with 3" strapping

• Material: Steel Plate

• Finish: Black Painted

• Design Factor: 3:1

RING - WELD-ON D-RING TIE DOWN

• Rated in Metric Ton(s)

Failure to use binders properly may result in serious injury or death. DO NOT operate load binder while standing on the load. Keep yourself out of the path of the moving handle and loose chain lying on the handle. You must be familiar with regulations regarding size and number of chain systems required for securing loads. Always consider the safety of nearby workers as well as yourself when using load binder. While under tension, load binder must not bear against an object, as this will cause side load. Do not use handle extender. Do not attempt to open or close the binder with more than one person.

TIE DOWN CARGO STRAP - RATCHET

• WLL marked along entire length of webbing.

• Material: Grade 70, Carbon Steel, Polyester

• Standard: EN 12195-2,3, WSTDA-T-1

• Finish: UV Protection, Yellow Chromate

• Design Factor: 3:1

• Identification: Trademark, Size/WLL

TIE DOWN CARGO STRAP - RATCHET

• WLL marked along entire length of webbing.

• Material: Grade 70, Carbon Steel, Polyester

• Standard: EN 12195-2,3, WSTDA-T-1

• Finish: UV Protection, Yellow Chromate

• Design Factor: 3:1

• Identification: Trademark, Size/WLL

BUCKLE - RATCHET

• Material: 304 Stainless Steel

• Finish: Stainless Steel

BUCKLE - RATCHET

• Finish: Zinc plated

Failure to use binders properly may result in serious injury or death. DO NOT operate load binder while standing on the load. Keep yourself out of the path of the moving handle and loose chain lying on the handle. You must be familiar with regulations regarding size and number of chain systems required for securing loads. Always consider the safety of nearby workers as well as yourself when using load binder. While under tension, load binder must not bear against an object, as this will cause side load. Do not use handle extender. Do not attempt to open or close the binder with more than one person.

WEBBING - TIE DOWN MATERIAL, POLYESTER

HOOK - WIRE, DOUBLE J

LINK - CARABINER, SELF-LOCKING, WITH CAPTIVE PIN, N-259G

• Material: Steel

• Standard: CSA Z259.12, EN 362, AMSI Z359

• Finish: Yellow Zinc

• Identification: Trademark, Batch Code, Size/WLL

LINK - CARABINER, SELF-LOCKING, WITH CAPTIVE PIN, N-252G

• Material: Steel

• Standard: CSA Z259.12, EN 362, AMSI Z359

• Finish: Yellow Zinc

• Identification: Trademark, Batch Code, Size/WLL

LINK - CARABINER, SELF-LOCKING, WITH CAPTIVE PIN, N-256G

• Material: Steel

• Standard: CSA Z259.12, EN 362, AMSI Z359

• Finish: Yellow Zinc

• Identification: Trademark, Batch Code, Size/WLL

LINK - O-RING, N-489

• Material: Forged Steel, Heat Treated

• Standard: CSA Z259.12, EN 362, AMSI Z359

• Finish: Yellow Zinc

• Identification: Trademark, Batch Code, Size/WLL

HOOK - REBAR, N-3630

• Material: Forged Steel, Heat Treated

• Standard: CSA Z259.12, EN 362, AMSI Z359

• Finish: Yellow Zinc

• Identification: Trademark, Batch Code, Size/WLL

HOOK - SNAP, N-3610

• Material: Forged Steel, Heat Treated

• Standard: CSA Z259.12, EN 362, AMSI Z359

• Finish: Yellow Zinc

• Identification: Trademark, Batch Code, Size/WLL

HOOK - REBAR, N-3620

• Material: Forged Steel, Heat Treated

• Standard: CSA Z259.12, EN 362, AMSI Z359

• Finish: Zinc Plated

• Identification: Trademark, Batch Code, Size/WLL

Ocean Brand

HARNESS - BACK D, 3 ADJUSTMENTS

• 1 attachment on the back

• 3 adjustment points on the chest strap & leg straps

• 2 lanyard parking attachment, breaking under 120 lbs

• Regular mating buckles on the chest strap & leg straps for adjustment

• Two fall indicators on the back torso straps

• Compliant / Certified to ANSI Z359.11-2014 & CSA Z259.10-2018

• Size: Universal

• Capacity: 352 lbs (160 kgs)

HARNESS - BACK D, 3 ADJUSTMENTS

• 1 attachment on the back

• 3 adjustment points on the chest strap & leg straps

• 2 lanyard parking attachment, breaking under 120 lbs

• Regular mating buckles on the chest strap

• Grommet adjustment on the leg straps

• Two fall indicators on the back torso straps

• Compliant / Certified to ANSI Z359.11-2014 & CSA Z259.10-2018

• Size: Universal

• Capacity: 352 lbs (160 kgs)

HARNESS - BACK D, 5 ADJUSTMENTS

• 1 attachment on the back

• 5 adjustment points on the shoulder straps, chest strap & leg straps

• 2 lanyard parking attachment, breaking under 120 lbs

• Regular mating buckles on the chest strap shoulder straps & leg straps for adjustment

• Two fall indicators on the back torso straps

• Compliant / Certified to ANSI Z359.11-2014 & CSA Z259.10-2018

• Size: Universal

• Capacity: 352 lbs (160 kgs)

HARNESS - BACK D, 5 ADJUSTMENTS

• 1 attachment on the back

• 5 adjustment points on the shoulder straps, chest strap & leg straps

• 2 lanyard parking attachment, breaking under 120 lbs

• Regular mating buckles on the chest strap & shoulder straps for adjustment

• Grommet adjustment on the leg straps

• Two fall indicators on the back torso straps

• Compliant / Certified to ANSI Z359.11-2014 & CSA Z259.10-2018

• Size: Universal

• Capacity: 352 lbs (160 kgs)

HARNESS - BACK & SIDE D, 5 ADJUSTMENTS

• 3 attachments on the back & waist sides

• 5 adjustment points on shoulder straps, chest strap & leg straps

• 2 lanyard parking attachment, breaking under 120 lbs

• Regular mating buckles on the chest strap, shoulder strap & leg straps for adjustment

• Two fall indicators on the back torso straps

• Compliant / Certified to ANSI Z359.11-2014 & CSA Z259.10-2018

• Size: Universal

• Capacity: 352 lbs (160 kgs)

LANYARD - SINGLE

• Single Leg internal shock absorbing lanyard

• With two snap hooks

• Classification: 6ft

• Capacity Range 150 lbs - 310 lbs

• Compliant / Certified to ANSI Z359.13-2013 & CSA Z259.11-2017

LANYARD - SINGLE

• Single Leg internal shock absorbing lanyard

• With one snap hook & one rebar hook

• Classification: 6ft

• Capacity Range 150 lbs - 310 lbs

• Compliant / Certified to ANSI Z359.13-2013 & CSA Z259.11-2017

LANYARD - DOUBLE

• Twin Legged external shock absorbing lanyard

• With one snap hook & two rebar hooks

• Classification: 6ft

• Capacity Range 150 lbs - 310 lbs

• Compliant / Certified to ANSI Z359.13-2013 & CSA Z259.11-2017

Tool Lanyard

• Tool tether with bungee & tubular webbing

• With a screw locking steel carabiner at the end

• Non-stretched length: 38" (97cm)

• Full extended length: 51" (130cm)

• Max. Capacity: 15.0 lbs

• Conforms to ANSI/ISEA 121-2018

Tool Lanyard

• Tool tether with bungee & tubular webbing

• With a twist locking aluminum carabiner at the end (Yoke N-2301-CP)

• Non-stretched length: 38" (97cm)

• Full extended length: 51" (130cm)

• Max. Capacity: 15.0 lbs

• Conforms to ANSI/ISEA 121-2018

Tool Lanyard

• Tool tether with bungee & tubular webbing

• With a twist locking aluminum carabiner with pin (Yoke N-2301-CP)

• Non-stretched length: 38" (97cm)

• Full extended length: 51" (130cm)

• Max. Capacity: 30.0 lbs

• Conforms to ANSI/ISEA 121-2018