LEGEND:
30
28
1
FFL RL 8.16 - L1
2
1
Structural Column Steel Rectangular Hollow Section 750x150x5
2
External Double Glazed Units Thermotech IGU - 13.52mm thick Sunergy Clear Heat Strengthened Laminated - 12mm Argon Gap - 8mm VFloat Clear Toughened - 35mm IGU Thickness
3
5mm Thick Steel Infill Plate - C’Sunk Fixing and Spacer - Angled 1 degree to Pergola - Paint Finish Micaceous Iron Oxide (Natural Grey)
4
Austral Brickwork (150x150x50) - Zinc with Graffiti Coat
5
Ability Chemicals Mortar - Abilox Premium Special Black 8.3% with in grey cement by weight. - Powdered with metallic oxides
6
15ms Plate Butt Weld
7
300x600 Reinforced Concrete Column
8
Pocket Cast in for Steel Mulion
9
150 EA Bolted to 75x50x5 UA Trimmed
10
Brickwall Cavity Flashing
11
150mm Steel Stud - PFC Trimmer Fixed to Slab Edge Beam
12
Bradford CSR 110mm Thick Soundscreen
13
Bradford CSR Sarking - Thermofoil 730 Medium Duty
14
Brick Cavity Ties on Every Second Course
15
Concrete Column Reinforcements - 8N20 Bars - R10 Ligs at300 centres (40MPa)
16
Connection between the Reinforced Concrete Column to the Structural Slab - Starter Bars
17
Reinforcement Bars on Slab (700x1200) - Ligatures: R12 at 300 centres
18
Reinforcement Bars on Slab (700x1200) - 2N16 Top - 1N16 Face Bar - 2N16 Bottom
19
Post Tensioned Slab (Dead End Anchorage)
20
Bradford CSR 215mm Thick Gold Batts
21
150 EA Support Bracket for Edge Trim - Mechanically Fixed to Slab
22
75x50x5 UA fully welded to 45x5 Steel Plate Trim - Fixing Tabs for Infill Plate at 450 centres
23
100 RHS Pergola Beam at 345 centres - Fixing Lug for Pergola Welded to Steel Edge Trim
24
2230x1930 Swing Door - Continuous Edge to Match Load Bar - 3mm Thick Aluminium Face Plate as Detailed with Inset Metal Lock Box - 3mm Metal Plate (Aluminium Plate Fully Welded to Frame and to Form Stop/ Cover to Lock and Strike - Hinges: Goliath Hinge BB G4 - Shoot Bolts: One to Fixed Gate. Goliath 600x12mm Tower Bolts - Anodised Australian Aluminium Finishing ‘Eversheild External’ Minimum 25 Microns with Exterior Matt Finish Framing System - 8mm Thick Mild Steel Metal Plates - Fully Seam Weld Junctions - Grind and Fill Welds Required for Smooth Finish - Paint Finish Micaceous Iron Oxide (Natural Grey)
25
8mm Thick Metal Plate using Masonry Anchors even spaced at maximum 600 centres - Welded Hinge - Paint Finish Micaceous Iron Oxide (Natural Grey)
26
Metal Angle Fixed to Perimeter of Ceiling Panels with Paint Coat Finish
27
50x50x3 Aluminium Channel with Glazing Block with Dulux Powdercoat Electro Vintage Silver - Silicon Seal
28
50x50x6 Aluminium Angle Cut Back to 50x30x6 and Folded to Match Angle of Glazing - Screw Fix to Steel Column - Silicon Seal
29
Perforated Plasterboard Suspended Ceiling (Boral)
30
Carpet with Custom Colour - ET96109-6 - Rugs Carpet and Design by ERTE Collection - HL 630 with Mod 750
6 18 8 2
17
3 3
19 27 9
21
16 14 18
23 5
22 25 4
15 CL RL 6.95 - L0
7 5
20 10
4
11 29 12 26
13
24
PROJECT NAME: AXONOMETRIC DRAWING GLASSHOUSE - COLLINGWOOD GF & FF CONJUNCTION
STUDENT NAME STUDENT NUMBER TUTORIAL LEADER TUTORIAL NUMBER
: CHARENSIA PRICILLA ROMPIS : 860209 : David Ash : 20
SECTION E - not to scale
SCALE 1:10 SCALE BAR: 1m N
0
5mm 3mm
LEGEND:
10
1
750 x 150 x 5 Rectangular Hollow Section
2
16 Mild Steel Plate, 6 Continuous Fillet Weld
3
2M20 8.8/s Bolts Each Member
4
12 Mild Steel Plate, 6 Continuous Fillet Weld
5
150 Parallel Flange Channel
6
C150 19 Steel Purlin @1200 Centres
7
Z250 19 Steel Purlin Lapped @1200 Centres
8
Lysaght Roof Sheeting - Kliplock Profile Polycarbonate (Translucent) - Installed with 75mm Fletchers Roof Rack System to all Purlins (Insulations and Roof Clip underneath the sheeting)
9
Lysaght Roof Sheeting - Kliplock 406 BMT 0.48 (Zincalume) - Installed with 75mm Fletchers Roof Rack System to all Purlins (Insulations and Roof Clip underneath the sheeting to maintaion insulation depth)
10
Roof Rack Insulation Spacer
11
Fletchers 100MM Permastop (R(m)2.5) Building Blanket with Heavy Duty Foil Sisalation Adhered
12
Insulation Safety Mesh with 15mm Lag Between Purlins to Allow Insulation to Recover to 100mm Nominal Depth
13
Gold Batts 215mm Thick (R(m)4.1)
14
28mm Furring Channel
15
Roof Truss Top, Bottom & Vertical Chords: 150 Universal Column 30
16
12mm Thick Full Depth Stiffener with 6 Continuous Fillet Weld on Both Sides
17
Roof Truss - Diagonals: 90 x 8 Equal Angle
18
20mm Tension Rods (Roof Brace)
19
Galvanised Furring Channels Max @600 Centres as Required for Fixing
20
Galvanised Suspension Rods
21
Suspension Direct Clips
22
Top Cross Rail 0.75 BMT
23
Rondo Key-Lock System - Flush Plasterboard Suspended Ceiling
24
Hunter Douglas - Blind System - Commercial ‘Quantum’ Blind Ssystem - Two Rollers to Provide Dual Blind System - Motors: Somfy Sonesse (Switch Motors) Controlled via Building Management System - Bottomrail: Ellipse Bottomrail in Extruded Aluminium - MDF Blind Bulkhead Above
25
Steel Packers
26
250 Universal Beam 31 - 12 Cleat Plate, 6 Continuous FIllet Weld, 2M20 8.8/s Bolts
27
Steel Beam - 12 Cleat Plate, 6 Continuous FIllet Weld, 2M20 8.8/s Bolt - 10mm End Plate, 6 Continuous Fillet Weld
28
Metal Cladding - VMZinc Vertical Interlocking Panel System - 300mm Panel Width x 24mm Panel Depth - 10mm Joint Width - Finish: 1mm Thick Pre-Weathered Antra Zinc - Installed with Galvanised Furring Channels @600 Centres to Maintain 20mm Unobstructed Ventilation Air Gap Behind the Metal Cladding - Provide ‘Enviroseal ProctorWrap Commercial’ Vapour Permeable Membrane to All Areas of Zinc Cladding - Install Panel Clips, Folded Interior Flashings, Folded Exterior Flashings, Folded Cappings & Folded Stop Ends. - Install Compatable Neutral Silicon Sealant When Necessary - Provide Continuous Bond Breaker Where Material May Come Into Contact with Incompatable Metalic Materials - Provide Insect Screen to all Ventilation Gaps within Zinc Cladding Systems
29
External Double Glazed Units Thermotech IGU - 13.52mm thick Sunergy Clear Heat Strengthened Laminated - 12mm Argon Gap - 8mm VFloat Clear Toughened - 35mm IGU Thickness
30
Danpalon Translucent Sheet Soffit - 16mm Mulitcell 1040 Wide (Opal)
11 12
7
9
13
14 15
18
16 17 26
8
15 27
7
1
5 2
5
5
RL CL 13.70 - L2
19
3 20 5 4
5
25 6
21 26
22 23
5 24 6
19
11 6
5 6 5
27
6 RL CL 12.05 - L1 5
30
14
28
5 29
28
28 14
6
5
PROJECT NAME: AXONOMETRIC DRAWING GLASSHOUSE - COLLINGWOOD
STUDENT NAME STUDENT NUMBER TUTORIAL LEADER TUTORIAL NUMBER
: CHARENSIA PRICILLA ROMPIS : 860209 : David Ash : 20
SECTION E - not to scale
SCALE 1:10 SCALE BAR: 1m N
0
5mm 3mm