Sealey leaflet Autumn - Winter 2020/21

Autumn-Winter 2020/21 3 and 4Tonne Trolley Jacks with Rocket Lift

or

PROTECTIVE SLEEVE

MAGNETIC TRAY

Model No. SEA 3040AG

LARGE JACKING SADDLE

Model No. SEA 3040AY

Model No. SEA 3040AO

UNIVERSAL JOINT

TWIN PISTON

• Heavy base design and large jacking saddle for increased load stability.

• Universal joint release mechanism allows safer, more controlled lowering of the jack.

• Rocket Lift feature brings lifting arm into contact with jacking point with minimal pumps.

• Polyurethane wheels for smoother manoeuvrability and helps prevent damage to workshop floor.

• Protective jack handle sleeve helps prevent accidental damage to car bodywork.

• 2 Year Warranty - 2nd year subject to T&Cs and registration on website (www.sealey.co.uk).

Colour

Capacity

Min./Max. Saddle Height

Max. Chassis Height

Length

Weight

SEA 3040AG

Green

3tonne

100/533mm

162mm

740mm

38kg

SEA 3040AO

Orange

3tonne

100/533mm

162mm

734mm

38kg

SEA 3040AY

Yellow

3tonne

100/533mm

162mm

734mm

38kg

SEA 4040AG

Green

4tonne

100/533mm

162mm

751mm

44kg

SEA 4040AO

Orange

4tonne

100/533mm

162mm

751mm

44kg

SEA 4040AY

Yellow

4tonne

100/533mm

162mm

751mm

44kg

Model No.

2tonne Low Entry Short Chassis Trolley Jacks & Accessories Bag Combo

Model No. SEA 1020LEBAGCOMBO

3tonne Standard Chassis Trolley Jack with Axle Stands (Pair)

Model No. SEA 1020LEHVBAGCOMBO

Package includes: • • • •

Model No. SEA 1020LEBAGCOMBO SEA 1020LEHVBAGCOMBO

Colour

Package Includes

Red

SEA 1020LE, SEA AP600JB, SEA AS2000F, SEA WCF01, SEA S0472 SEA 1020LEHV, SEA AP600JB, SEA AS2000F, SEA WCF01, SEA S0472

Hi-Vis Green

Jack Min./Max. Saddle Height: 133/515mm.

Single-piece hydraulic unit with heavy chassis design.

Integral American cog-type release mechanism and long two-piece handle.

Heavy-duty castors and large saddle design ease positioning under vehicle.

Fitted with safety overload valve and pump-through valve to prevent handle locking at maximum ram extension.

• Ideal for loaded vans up to 3.5tonne GVW. • Supplied with Ratchet Type Axle Stands, 3tonne (3000kg) capacity per stand (6tonne (6000kg) per pair).

Model No. • Axle Stand Min./Max. Working Height: SEA 3010CX 285/420mm.

• • • • •

AP600JB - 600mm Trolley Jack Bag AS2000F - Folding Axle Stands (Pair) 2tonne Capacity per Stand WCF01 - Folding Wheel Chocks - Pair S0472 - 3pc 1/2"Sq Drive Extendable L-Bar Wrench Set

1.5tonne Floor Transmission Jack

300kg Engine Support Beam

• Min./Max. Saddle Height: 170/810mm.

• Precision valve allows delicate adjustment when taking out gearbox and realigning during replacement.

• Includes two chains for safe loading.

• Supplied with pulling hook and four castors for extra manoeuvrability in confined spaces.

• Fully adjustable saddle with forward and backward tilt.

• • • •

Model No. SEA TJ1500F

Min./Max. Width: 585/1580mm.

Supports and accurately positions engine.

Ideal for replacing anti-vibration mountings.

Aids the removal of gearboxes and transmissions.

Model No. SEA ES300

Viking Low Entry Trolley Jacks with Rocket Lift

• Rocket Lift feature brings lifting arm into contact with jacking point with minimal pumps.

• Polyurethane wheels for smoother manoeuvrability and helps prevent damage to workshop floor.

• Protective jack handle sleeve helps prevent accidental damage to car bodywork when pumping the handle.

• Foot pedal for quick approach of the lifting saddle to the vehicle in confined spaces.

• Includes removable rubber saddle pad and built-in tool tray for fasteners and tools.

• 3 Year Guarantee - 2nd & 3rd year subject to T’s&C’s and registration on website (www.sealey.co.uk).

2tonne High Lift Low Entry Trolley Jack

Min./Max. Saddle Height

Max. Chassis Height

940mm

75/530mm

150mm

700mm

95/500mm

180mm

799mm

100/533mm

158mm

Capacity

Length

SEA 2100TB

2tonne

SEA 3100TB

3tonne

SEA 4040TB

4tonne

680kg Load Sling Adjuster • Handles and levels heavy, off-centre loads quickly and easily.

• Ball bearing handle allows for a smooth and easy adjustment.

• Three adjustment holes accommodate different sized engines.

• If used with cranes of capacity 680kg or more, the load must be restricted to 680kg maximum.

• Supplied with 4 x 275mm chains and 4 x ‘L’ shaped brackets with additional karabiner styled screw links.

• Min./Max. Saddle Height: 80/805mm.

• High-lift jack arm with incredibly low minimum access height of just 80mm.

• Fitted with quick lift foot pedal and dead man’s control.

• Heavy-duty long steel chassis with wide wheelbase provides inherent stability and easy access to deep set jacking points.

• Fitted with one-piece hydraulic unit with built-in safety overload protection.

Model No. SEA LS501

1.5tonne Vertical Transmission Jack

Model No. SEA 2200HL

2tonne Short Chassis Trolley Jack • Min./Max. Saddle Height: 117/322mm.

• Chassis Length: 440mm.

• Steel chassis with welded castor supports and one-piece hydraulic unit.

• Fitted with overload valve and finger cover for extra safety.

• Suitable for the hobby user or as an emergency mobile jack.

• Includes one-piece pumping handle and carry handle.

Model No. SEA 1050CX

2

Model No.

• Min./Max. Saddle Height: 1120/1950mm.

• Heavy-duty construction and foot-pedal hydraulic control.

• Extremely stable in operation due to 4-wheel configuration.

• Spring loaded dead man’s safety release control reduces the risk of inadvertent lowering.

• 2-Way hydraulic unit ensures that the saddle lowers at a controlled speed at all times, even without load.

• Extra-large castors allow for increased manoeuvrability.

• Hydraulic unit larger than the economy models for improved performance and durability.

• Supplied with four-arm transmission saddle.

Model No. SEA 1500TR

2tonne Folding Crane

5tonne European Style Trolley Jack

• • • • • • • • • • •

Lifts 2000kg at 930mm jib extension.

Folds for easy storage.

Side pump access with removable handle.

Delivered in knock-down form.

Some self-assembly required.

Model No. SEA PH20

Car Ramps Low Entry 1.5tonne Capacity per Ramp 3tonne Capacity per Pair

• Made from durable polypropylene.

• These ramps are designed to allow jacking access to suitable jacking points on the vehicle.

• Not intended to raise a vehicle enough for under vehicle servicing.

• Overall Dimensions (L x W x H): Model No. 700 x 200 x 80mm.

SEA CAR3000LR

• •

Min./Max. Saddle Height: 150/583mm.

Chassis Length: 1305mm.

European style trolley jack manufactured to exacting standards.

Lifting arm has 2-speed lifting and lowering; lowers rapidly without load and provides smooth, slow, controlled lowering with load.

Lift-and-twist ‘Dead Man’ mechanism operated via ‘D’ shaped handle prevents accidental lowering.

Nylon wheels fitted which are quiet in operation and help prevent damage to garage floors.

Foot pedal for quick approach of the lifting saddle to the vehicle.

Includes removable rubber saddle pad and built-in tool tray for fasteners and tools.

Model No.

SEA 5000ES

Car Ramps 1.5tonne Capacity per Ramp 3tonne Capacity per Pair

• Manufactured from durable polypropylene.

• Suitable for professional or serious DIY applications.

• Overall Dimensions (L x W x H): 900 x 300 x 215mm.

Model No. • Maximum Tyre Width: 260mm.

SEA CAR3000C

10tonne Telescopic Low Entry Bottle Jack

Min./Max. Height: 128/223mm.

Telescopic two-stage ram for higher maximum lift.

Compact closed height.

Cast base with threaded components.

• Supplied with 4pc Model No. operating handle.

• Carrying handle.

SEA BJ10LE • • • •

Jacking Beams with 1.6m Extending Arms & Flat Roller Supports • Fully certified and approved to comply with MOT requirements.

• 1.6m Load arm reach.

• Beam Lift: 95-300mm.

• Two-stage mechanical safety lock and telescopic finger guards.

• Spring loaded flat arms with roller bearings.

• Optional hook arms supplied.

• Supplied with two pairs of aluminium support blocks.

• Wide lift configuration meets MOT recommendation for lifting on jacking point.

Model No.

or

Capacity

SEA SJBEX200

2Tonne

SEA SJBEX300

3Tonne

3

20tonne Floor Type Hydraulic Press

900A 12V RoadStart® Emergency Jump Starter - Hi-Vis Green

• Cable & Clamp Length: 0.72m.

• Composite hi-vis green case with moulded rubber protection, integral battery cable storage and carry handle.

• LED Battery condition, polarity check, with audible warning if polarity is reversed, and charge indicators.

• Features independent on/off switch which allows the positive clamp to be connected without the risk of sparking and an integral LED work light for use at night.

• Fitted with two 12V power sockets that will accept any 12V device fitted with a vehicle accessory socket plug.

• Features a USB outlet (5V/1A).

Table Aperture: 100mm.

Working Table Width: 630mm.

Ram Stroke: 185mm.

Overall Height: 1796mm.

Detachable pump and ram allowing hydraulics to be used for other purposes when press is not in use.

• Supplied with gauge.

• • • • •

Model No. SEA RS1312HV

Composite Creeper with 4 Wheels

Model No. SEA YK20F

37L Shot Blaster with Water Trap & Wheels • • • • •

One piece, moulded high impact polymer creeper.

Padded headrest.

Low profile.

Four Ø50mm swivel castors.

Size (L x W x H): 915 x 410 x 95mm.

Model No. SEA SCR80S

Portable Soda Blasting Gun

• Pressurised tank for maximum power.

• Supplied with 2.4m rubber hose, five ceramic nozzles and in-line water trap for moisture-free grit blasting.

• Also includes bayonet air line coupling and airflow regulator.

• Accepts a variety of grits up to 700microns and is suitable for stripping rust and paint from wheels, chassis, panels and other corroded/painted surfaces.

Model No. SEA SB997

25kg Blasting Soda Bag

• Blasting soda for use in conjunction with Model No’s SB99.KIT, PSB10, PSB40 and other brands of soda blasters.

• Soda leaves a rust inhibitor behind for up to six weeks.

• Grade/Size: Extra Coarse/285microns.

• Suitable for removing rust, paint, mould, grease, from fibreglass, brick, stone, marble, tiles, glass, rubber and bearings.

4

• Suitable for controlled removal of paint, mould, carbon, grease and rust.

• After blasting, the remaining surface will inhibit rust for up to six weeks.

• Adjustable nozzle allows control from narrow to wider stream.

Model No.

SEA PSB05

25kg Shot Blasting Grit

Model No. SEA SBG25KG

• Suitable for workshop, hand-held and recirculating shot blasters.

• Complies with COSHH SI-1657-1988. Not suitable for use in shot blasting cabinets.

Model No. SEA B/25KG

12V ElectroStart® Batteryless Jump Starters Model No. SEA E/START1600

• Innovative technology with no internal battery so no need to wait hours for the unit to charge before use.

• Simple and safe to use with no long term battery storage issues.

• Can be fully energised in a matter of minutes.

• Compact and lightweight for easy handling Model No. SEA E/START800 and storage, yet still delivers the same result as heavy, bulky, lead acid battery equivalents.

• Ideal for the professional mechanic and DIY users.

Model No.

Output Start Peak (EN)

E/START800

800A(400A)

E/START1100

1100A(550A)

E/START1600

1600A(800A)

Bobbin Supports for RPS2

Motorcycle Chain Breaker & Riveter

• Breaks and rejoins most types of chain quickly and easily.

• Suitable for most sizes of drive or cam chain from #35 to #630.

• Supplied with a range of pins, dies and detailed instructions.

• Optional Bobbin Support for Model No. RPS2.

• Designed to give extra support and added stability once rear axle has been located and raised.

• Yellow phosphate finish for added corrosion resistance.

Model No. SEA RPS1BS

SEA LED185W

12 SMD LED + 1W LED Rechargeable Slim Inspection Lamp • Slimline foldout inspection lamp for use in confined spaces, with 6mm minimum thickness.

• Inspection arm can be rotated 180° and folded back for use as a hands-free inspection lamp.

• 12 SMD LED inspection lamp which produces up to 400 lumens, operated by a rolling dimmer switch.

• 1W SMD LED in the end for use as a directional torch.

• Suitable for hands-free operation with three magnets and a hanging hook.

• Folds away, small and compact, suitable for keeping in your pocket.

• 3.7V 2Ah rechargeable Li-ion battery.

• Supplied with USB charging lead.

• Operating Time: Inspection Lamp (400lm); 3hr, Directional Torch; 8hr.

• Charging Time: 3hr.

• Removable 4 SMD LED lamp produces up to 120 lumens.

• Rechargeable 3.7V 300mAh Li-Polymer battery.

• USB Socket for charging.

• Model No. LED185W has wireless headphones, with wireless transmission up to 10m. Wireless headphones charged via micro USB.

SEA LED185

Model No. SEA VS779 Model No. LED185W

4 SMD LED USB Rechargeable Beanie Hats

Model No.

Model No. SEA E/START1100

Wireless Headphones

Model No. SEA LED180

û ü

360° 3W COB + 1W LED Rechargeable Inspection Lamps

• 360° swivel and tilt function.

• 3W COB LED producing up to 300 lumens with a CRI-80 rating.

• Even and constant spread of light.

• 1W High power LED directional torch.

• Base magnet and swivel hook for hands-free operation.

• Rechargeable 3.7V 1.5Ah Li-Polymer battery.

• Operating Time (Side/Top): 3/6hr.

• Micro USB charging port.

Model No.

Colour

SEA LED3601R

Red

SEA LED3601G

Hi-Vis Green

SEA LED3601

Black

5

500ml Oil Suction Syringe Composite Body

500ml Oil Suction Syringe Metal Body

• Painted cast steel tube with T-Bar type plunger.

• Particularly useful for removal of oil from gearboxes and differentials.

• Supplied with 300mm flexible Model No. suction hose.

SEA AK46

Quick Release 3-Way Fill Pistol Type Grease Gun

• Single action composite bodied suction tube with T-bar type plunger.

• Ideal for use on vehicles and machinery for removing oil from gearboxes and differentials.

• Supplied with 300mm Model No. transparent flexible suction hose with 10mm bore.

SEA AK47

18V Cordless Grease Gun

• Pistol style grease gun with contoured handle.

• Die-cast aluminium pump head.

• Air-bleed valve.

• 3-Way fill with cartridge, bulk and manual capability.

• Supplied with a rigid delivery tube, push-on hydraulic 4-jaw coupling.

• Accepts standard 400g cartridges.

6.5L Manual Vacuum Oil & Fluid Extractor

• High power, professional, cordless grease gun, developing 8000psi.

• Ideal for in-field lubrication where power and speed are required.

• Suitable for screw type and standard 400g cartridges, manual or bulk filling.

• Features LCD battery condition indicator, air bleed and heavy-duty aluminium pressure head.

• Supplied with 18V 2Ah Lithium-ion battery and mains charger.

Model No. SEA CPG18V

• Ideal for other liquids such as water and soluble oil.

• Supplied with Ø4, Ø6 and Ø8mm suction probes and a Ø10mm x 1m extension tube.

• Avoids searching for drain plug Model No. keys and getting under the vehicle.

SEA S01169 • Ideal for mobile mechanics.

1L Multipurpose Mini Pump

180ml Oil Can

500ml Metal Oil Can with Flexible Spout

• Multipurpose pump perfect for topping up difficult to access points on motor vehicles, lawnmowers, chainsaws and other jobs around the workshop and home.

• Suitable for all engine oils, transmission fluids, brake fluids and general purpose cleaners.

• Metal can with flexible spout for directional control.

• Trigger operated action for high pressure oil spray.

• Metal can with flexible spout and thumb operated lever action.

Model No. SEA TP6804

Model No. SEA TP04

Model No. SEA TP05

Ø160mm Funnel with Flexible Spout & Filter

• • • •

Polyethylene funnel resistant to oil, fuel and some acids.

Removable two-step flexible spout.

Ideal for vehicles with smaller diameter unleaded filler necks.

Fitted with handle and removable brass filter.

Model No.

SEA F16F

6

Model No. SEA AK481

3pc Fixed Spout Funnel Set

Screw Cap with Tap for FC20 & FC25

• Polyethylene funnel set suitable for many fluids including detergents, pesticides, diesel and petrol.

• Contains Ø75mm, Ø150mm and Ø250mm funnels with hanging tabs.

• Not suitable for acetone, gun wash or thinners.

• Fitted with an adjustable tap opening providing increased fluid control.

• Manufactured from high impact polyethylene.

Model No. SEA F98

Model No. SEA FCT01

8L Oil/Fluid Drain Pan

7.6L Oil/Fluid Drain Pan

17L Antifreeze/Fluid Drain Pan

• Made from high density polyethylene with UV stabilisers.

• Large enough for single oil change.

• Includes oil pouring lip, hanging hole and back-shelf with protruding stub for oil filters.

• Made from high density Polyethylene with UV stabilisers.

• Features anti-splash lip that contains fluid when carrying or pouring.

• Large handles and enclosed pouring spout aid return of oil/fluid to recycling container.

• Made from high density Polyethylene with UV stabiliser.

• Features anti-splash lip that contains fluid when carrying or pouring.

• Large handles and enclosed pouring spout aids return of oil/fluid to recycling container.

• Colour-coded to help keep Model No. different fluids isolated and reduces cross contamination.

SEA DRP04

Model No. SEA DRP01

Model No. SEA DRP02

10L Oil/Fluid Drain & Recycle Container

5L Oil Container with Lid & Flexi-Spout

• Tough polyethylene jug resistant to oil and most acids.

• Removable flexible spout.

• Screw cap and lid enables jug to be used as a container, to ensure safer handling of liquid, preventing spillages.

• • • • •

Suitable for both the DIY user and professional mechanic.

Purpose made for the recovery of oil and antifreeze.

Polyethylene with UV stabiliser.

Heavy wall construction stays rigid, even with hot oil.

Excess capacity helps prevent overflow or spillage.

Metal Drain Pans

• Zinc die-cast, push-pull tap.

• Locking facility to prevent unauthorised access.

• Nitrile seals, suitable for most liquids normally stored in plastic and steel drums.

Model No. SEA JDL5

Model No. SEA DRP07

3/4"BSP Zinc Die-Cast Lockable Drum Tap

Model No. SEA TP128

Low Profile Drip Trays • Low profile drip trays manufactured from hard-wearing recycled polypropylene.

• These have a broad appeal to both the classic car user and general mechanic.

• Purpose-made for the recovery of oil and fluids, these drip trays can be left under most vehicles due to the low profile design.

• Ideal for use over prolonged periods of time, catching any drips that may occur whilst in storage or in the workshop.

EA No. S odel

1

DRPM

M

Model

or

. SEA el No

09

A DRPL

No. SE

EA No. S odel

4 DRPM

Mod

L120

DRP

M or

• Zinc plated pans, ideal for oil changes, cleaning and storing vehicle components.

• May also be used as a drip tray under vehicles.

Model No.

Capacity

Size (W x D x H)

Model No.

Capacity

SEA DRPM1

9L

432 x 331 x 89mm

SEA DRPL09

9L

Size (W x D x H) 570 x 390 x 50mm

SEA DRPM2

12L

489 x 371 x 91mm

SEA DRPL15

15L

1000 x 120 x 1000mm

SEA DRPM3

16L

432 x 331 x 143mm

SEA DRPL25

25L

1100 x 550 x 50mm

SEA DRPM4

20L

489 x 371 x 153mm

SEA DRPL120

120L

1200 x 120 x 1200mm

7

Diesel Engine Setting/Locking Kit - VAG 1.2D, 1.6D, 1.9D, 2.0D TDi Common Rail - Belt Drive

• For VAG 1.4D, 1.9D, 2.0D TDi PD (Pumpe Duse) and 1.2D, 1.6D, 1.9D, 2.0D CR (Common Rail) engines with Mechanical (Friction Dampened) Belt Tensioner.

• Kit includes crankshaft locking tools (oval and round gears), plus camshaft and tensioner locking pins.

• Use with Associated Tool - Model No. Model No. VSE5752 Tensioner Adjuster Set.

Diesel Engine Setting/Locking Kit VAG 1.4D, 1.6D, 2.0D Common Rail Belt Drive

• Timing kit suitable for 1.2, 1.4TFSi and 1.4, 1.6FSi engines.

• Kit contains essential tools for crank TDC positioning, camshaft setting and tensioner locking.

Model No. SEA VSE5956A

• Essential Tools for timing belt replacement on Renault/Nissan 1.5D dCi diesels.

• Covers engine codes K9K. • These engines are also fitted in Suzuki and Dacia models.

• Covers the new generation three- and four-cylinder common rail diesel engines.

• Includes the tools required for setting the camshaft drive gears within the cylinder head.

Model No. SEA VSE2090

SEA VSE2358

Petrol Engine Setting/Locking Kit VAG 1.2, 1.4TFSi, 1.4, 1.6FSi Chain Drive

Diesel Engine Setting/Locking Kit Renault, Nissan 1.5dCi, Suzuki DDiS, Dacia dCi - Belt Drive

Petrol Engine Setting/Locking Kit Ford, Mazda, Volvo 1.25, to 2.3 16v Duratec - Belt/Chain Drive

• Covers the complete range of Ford Duratec engines 1.25 through to 2.3 16v in both belt and chain drive variants.

Diesel/Petrol Engine Setting/Locking Combination Kit Ford, PSA Belt/Chain Drive

Model No. SEA VSE5515

Model No. SEA VSE1901A

Auxiliary Stretch Belt Removal/ Installation Tool

• Designed for the recommended removal and installation of elasticated or stretch drive belts fitted to modern auxiliary drive systems such as the alternator or power steering.

• Prevents damage to the pulley and prolongs the Model No. life of the belt.

• Fits most crankshaft pulleys.

SEA VS787

53pc Diesel & Petrol Master Timing Tool Kit VAG - Belt/Chain Drive

• Suitable for a wide range of belt or chain driven petrol and diesel engines.

• Contains a camshaft sprocket puller and flywheel locking tools.

Model No. SEA VSE5042A

Petrol Engine Timing Tool Kit, GM 1.0, 1.2, 1.4, 1.6 - Chain Drive • Covers a wide range of Vauxhall/Opel and Chevrolet petrol engines.

• Includes the necessary tools for setting and locking the camshafts and crankshaft.

• Also includes the pins for locking the timing chain tensioner, locking tools for 1.0, 1.2, 1.4, 1.6 EcoTec/ecoFLEX (codes X and Z) chain engines, and the timing disc position gauge for the timing sensor on the inlet camshaft.

Model No. SEA VS5235

Model No. SEA VS5100MK

Petrol Engine Setting/Locking Kit - GM, Saab - EcoTec 1.4, 1.6, 1.8, 2.0, 2.2 16v Belt Drive • Designed to fit between camshaft sprockets to maintain camshaft timing position.

• Essential tools for timing belt replacement applications.

• Supplied as a pair.

Model No. SEA VS1700

8

• Master timing tool kit for VAG vehicles.

• Covers a wide range of petrol and diesel engines.

• Suitable for popular VAG vehicles from 1995 to present.

• Supplied in two high quality storage foams suitable for tool box drawers.

• Foam size: 560mm x 390mm x 45mm.

Diesel Engine Setting/Locking Kit Vauxhall/Opel 2.0D • Designed for Vauxhall/Opel/ Chevrolet 2.0D common rail diesel engine.

• Locks the engine in the correct position whilst changing the timing belt on the SOHC 16v engine range.

• Supplied in storage case with instructions and warning tag.

Model No. SEA VSE5009

Camshaft Sprocket Puller - Ford, Citroen, Peugeot, Mazda

• Three legged puller specifically designed to remove the camshaft sprocket on Ford, Citroen, Peugeot and Mazda diesel engines without causing damage to the pulley.

Model No. SEA VSE50422

Mini/BMW Engine Support Bracket

• Designed to provide a safe secure method for supporting the engine if the engine mounting has to be removed for cylinder head work.

• Prevents the engine from slipping or dropping unexpectedly.

• When installed the vehicle can be moved to another location without the need to use a lifting device.

• Suitable for N12, N14, N16 and N18 Engines fitted in BMW Mini models.

Model No. SEA VS5214

Crankshaft Pulley Alignment Tool Ford B-Max 1.6 EcoBoost

• Crankshaft pulley alignment tool for Ford B-Max 1.6 EcoBoost engine.

• Ensures the crankshaft pulley is correctly aligned with the timing belt cover.

Model No. SEA VSE5860

Flywheel Locking Tool Hyundai/Kia

• Used to hold the flywheel when removing or installing the crankshaft damper pulley.

• Fits a wide variety of Hyundai and Kia vehicles.

Petrol Engine Timing Belt Checking Gauge PSA, 1.0/1.2 - Belt Drive

• Suitable for PSA Group belt in oil engines.

• Fast and accurate way to check for belt degradation.

Model No. SEA VSE5935

Model No. SEA VSE5094

Petrol Engine Timing Tool Kit - VAG 1.2, 1.4TFSi, 1.4, 1.6FSi - Chain Drive

Petrol Engine Belt Replacement & Chain in Head Service Set VAG 1.8, 1.8T - Belt Drive

• Timing kit suitable for 1.2, 1.4TFSi and 1.4, 1.6FSi engines.

• Kit contains essential tools for crank TDC positioning, camshaft setting and tensioner locking.

• Suitable for belt tensioning 1.8 and 1.8 Turbo twin camshaft engines.

• These belt drive engines also have a chain connecting the two camshafts.

• Includes a belt tensioner bolt, belt tensioner pin and chain tensioner retainer.

Model No. SEA VSE5950

Model No. SEA VSE5909

8pc Petrol Engine Compression Test Kit

3pc Glow Plug Socket Set

• Compression tester fitted with Ø63mm gauge reading up to 300psi(20kg/cm²).

• Kit includes 130mm straight and angled push-on connectors, 300mm flexible extension with 10, 12, 14 and 18mm deep thread adaptors.

• Specialised socket set consisting of 8, 9 and 10mm sockets.

• Designed to remove and install glow plugs without having to cut the power lead off.

• Applications include Alfa Romeo, Fiat, GM and PSA engines.

Model No. SEA CT955

Model No. SEA SX4033

9

8 & 10mm Damaged Glow Plug Removal Set

• Designed to remove damaged/broken glow plugs from cylinder heads.

• Suitable for glow plugs with an M8 x 1mm and M10 x 1mm thread.

• Set includes all required adaptors for drilling, centring and pulling for the safe removal of glow plug.

Model No. SEA SX0408

Diesel Fuel Priming Set

Diesel Injection Leak Back Master Kit Bosch/Delphi/Denso

Glow Plug Analyser

• Enables fast diagnosis of glow plug failure or degradation without the need to disassemble the plug from the engine.

• Suitable for use on any 12V DC glow plugs and connects directly to the vehicle’s battery.

• Features 6 LED readout which indicates glow plug status and also if battery contains enough charge to power Model No. the plugs.

SEA VS212

Diesel Priming Kit - Ford

• A comprehensive fuel priming set fitted with the latest male and female quick connectors found on Fiat, Ford, Land Rover, Mercedes, PSA, Renault, Rover and Vauxhall/Opel vehicles.

• Designed to work in conjunction with the low pressure fuel circuit, to reintroduce fuel back up to the fuel line after maintenance.

• Clear pipes allow visual detection of any air within the fuel system or being inadvertently drawn into the fuel line.

• Two universal connectors and one clear pipe allow connection Model No. to older vehicles not fitted with quick release connectors.

SEA VS555

SEA VS2048

8L Vacuum Fuel/Fluid Extractor

• Designed to work in conjunction with the low pressure fuel circuit, to reintroduce fuel back up to the fuel line after maintenance.

• Clear pipes allow visual detection of any air within the fuel system or being inadvertently drawn into the fuel line.

• Includes a valve to work in conjunction with Ford IDS diagnostic equipment, allowing the vacuum to be monitored.

Model No. SEA VS552

• Updated kit designed to measure return fuel flow on diesel vehicles up to 6 cylinders, fitted with common rail injection system.

• Identifies worn, blocked or inoperative injectors quickly and easily.

• Contains measurement tubes for short term tests and measurement bottles for long term, more accurate evaluation.

• Master kit includes range of adaptors to suit Bosch, Delphi, New Delphi and Denso injectors for comprehensive coverage of Model No. common rail diesel vehicles.

• Suitable for the extraction of all types of engine, transmission and lubricating oils from vehicles and machinery.

• Also suitable for the extraction of petrol/diesel and low viscosity fluids.

• 1.5m Main hose, Ø6.7 x 700mm dipstick oil probe and Ø7 x 400mm universal fluid probe.

• Supplied with 240mm fuel system adaptor for use in conjunction with fuel kit Model No’s VS552, VS553, VS554 and VS555.

• Can also be used for draining fish tanks, basins and sinks.

Model No. SEA TP204

Fuel Filter Key Ford Transit

Vacuum Tester & Brake Bleeding Kit

Smoke Diagnostic Tool Leak Detector

• For removing and refitting fuel filter bowl when replacing the fuel cartridge.

• Multifunction diagnostic tool used to test a variety of essential engine and associated functions.

• Also includes reservoir, hoses and adaptors for bleeding brake and clutch systems.

• Brass-bodied vacuum pump with easy-to-read vacuum gauge.

• Contents: Vacuum Pump, Fluid Container, Transfer Cap, Vacuum Hoses; 2 x 560mm, 4 x 80mm, 5 x Assorted Vacuum Hose Fittings, 3 x Bleed Nipple Adaptors.

• Allows the technician to pinpoint all manner of system leaks including the air intake, cooling, evaporation, fuel, exhaust and vacuum systems.

• Features single button operation, flow control valve and auto power off.

• Uses mineral oil and workshop air to generate smoke at low pressure while connected to a vehicle.

• System is clean and quick to use and connects to a 12V vehicle battery.

Model No. • Rubber Cones Sizes (Ø): 10-45, 30-65, 50-85, 70-100mm.

SEA VS870 • Mineral oil not supplied.

Model No. SEA VS6428

10

Model No. SEA VS402

Combustion Leak Detector

250ml Combustion Leak Detector Fluid

• Diagnose blown gaskets, cracked blocks and cylinder heads on both petrol and diesel vehicles.

• Checks for CO2 in cooling system and indicates its presence by test fluid colour change.

• Use with cone adaptor or in conjunction with radiator caps from Model No’s VS001, VS0011, VS0013, VS0014, VS0033 and VS006.

• For Test Fluid Refill order Model No. Model No. VS0061F.

• Detector fluid refill for VS0061 & VS0062.

Model No. SEA VS0061F

SEA VS0061

Turbo System Leakage Tester

• Designed to charge the turbo system with a low pressure of regulated workshop air to show the presence of leaks within the system.

• Kit supplied with four pairs of stepped adaptors to fit most sizes of hose.

• Adaptor Sizes: 35-90mm.

• Features a pressure gauge, shut-off valve and pressure release valve.

Model No. • Can also be used on cooling system hoses.

SEA VS2030 • Supplied in storage case.

Infrared Laser Digital Thermometer 12:1

Infrared Twin-Spot Laser Digital Thermometer 12:1

• Detects energy emission in the infrared spectrum and converts reading into a display of temperature.

• Features laser pointer, data hold and auto power off.

• Temperature is displayed on a large 23mm LCD HD colour screen with back-lit display for use in low light areas.

• Temperature can be shown in either °C or °F. • Temperature Range: -50°C to +530°C (-58°F to +986°F).

• Powered by 2 x AAA batteries Model No. (not included).

• Detects energy emissions in the infrared spectrum and displays the temperature on an 18mm LCD back-lit display.

• Twin-spot laser guides user to the unit’s optimum targeting distance - when the two laser dots merge into one, unit is reading a 13mm disc of temperature.

• Features data hold and auto power off.

• Temperature can be shown in either °C or °F. • Temperature Range: -50°C to +650°C (-58°F to +1202°F).

Model No. • Powered by 9V battery (supplied).

SEA VS940

SEA VS904

Thermal Imaging Camera

Ø5.5mm Camera Video Borescope

• Combines the function of surface temperature measurement and real-time thermal imaging.

• Features a traditional image camera to pinpoint test area with the ability to mix the thermal image over the top at varying intensities.

• Includes on-screen cursor to accurately locate temperature hotspots.

• Suitable for many industries including automotive, building and electrical.

• Screen Size: 52mm.

• Focal Distance: 50cm (Min. 20cm, Max. 1m).

• Field of Vision: 65°.

• Powered by 4 x AA batteries (supplied).

• High performance pistol grip borescope with 85mm colour TFT screen and waterproof probe pod with IP67 rating.

• Features video record/playback, still images and stream live video via the AV out connection.

• Videos and images are stored on a 4GB micro SD card (supplied) allowing up to 4.5 hours of video and 10,000 images, which can be transferred to a PC via the USB connection.

• Also features digital zoom control and rotate/ flip control of image.

• Powered by Lithium-ion battery pack giving up to 4 hours continuous use.

• Kit includes 45° mirror and magnetic pick-up.

• AV and USB cables supplied.

Model No. SEA VS912

Ø5.5mm Camera Tablet Video Borescope

Diesel High Pressure Pump Test Kit • Features 2,000bar gauge, pressure relief valve and high pressure flexible hoses.

• The kit also includes a set of dummy pump regulator and injector pipe blanks.

• Kit allows for a variety of tests to be conducted: - Engine cranking/running pressure test - Maximum pump pressure test - Pump pressure regulator test - Injector leakage test

Probe Storage • Large 110mm TFT screen and tablet design makes the image incredibly clear but also very portable.

• Includes the added advantage of probe storage inside the rear of the case so no additional storage required.

• Features controls for light intensity, digital zoom and image rotation.

• Waterproof probe pod with IP67 rating and supplied in storage pouch.

• Powered by 4 x AA batteries (supplied).

Model No. SEA VS8231

Model No. SEA VS8223

Model No. SEA VS216

11

Diagnostic Socket Memory Safe EOBD

12V Diagnostic Socket Memory Safe EOBD

• Attaches to a 12V slave battery and provides power via the EOBD socket to on-board electronics whilst vehicle’s own battery is disconnected.

• Features LED to indicate back-up battery power supply status.

• Saves valuable time spent re-programming lost codes.

Model No.

• Used to preserve the memory to on-board electronics whilst vehicle’s own battery is disconnected.

• Saves valuable time spent re-programming lost codes.

• Can be connected via the vehicle’s EOBD or vehicle accessory power socket.

• Unit features an internal 12V 7Ah sealed battery and LEDs provide battery condition Model No. and charge indicator.

SEA VS2076 • Supplied with mains charger.

SEA VS2072

0-50V Automotive Wire Piercing Test Lead Probes

15 Function Digital Automotive Analyser with Inductive Coupler/Infrared Temperature Probe

• Fully insulated probes have a spring loaded clamp.

• Stainless steel pin self-centres and punctures the insulation.

• Fitted with Ø4mm banana style connectors.

• Maximum Wire Size: Ø3.5mm.

• For automotive use only, with a maximum input of 50V DC. Model No.

SEA TA114

• 15 Function, auto-ranging automotive diagnostic multimeter with infrared thermometer attachment.

• Combination digital/bar graph display gives accurate indication of component outputs.

• Large, easy-to-read high contrast display with bright, white back light.

• Workshop-tough, durable case with integral stand and auto power shut-off.

• High speed processing circuitry reads standard automotive parameters including duty cycle and pulse width making this tool ideal for testing fuel injection systems.

• Features auto-ranging, and data-hold functions with overload protection on all ranges.

• Includes relative functions including min./max. and peak hold.

• Supplied with inductive coupler, infrared Model No. temperature probe, test probes and thermocouple in storage case.

SEA TA304

8 Function Digital Multimeter with Thermocouple

• Heavy-duty general purpose multimeter with clear and easy-to-read LCD display.

• Features data-hold function, temperature probe and diode test facility.

• Housed in rugged rubber boot with integral stand.

• Supplied with full set of leads and probes.

• Measures: AC and DC Voltage, DC Current, Resistance, Temperature, Audible Continuity, Diode/Transistor Model No. Verification Mode.

SEA MM20

12

AC/DC Clamp Meter & Multimeter

8 Function Professional Auto-Ranging Digital Multimeter

• High precision auto-ranging multimeter.

• Conforms to EN 61010-1 CATIII 600V safety requirements for electrical equipment for measurement, control and laboratory use.

• Temperature measurement capability, max/data hold and auto power off function.

• Double moulded housing with soft grip case and large display for ease of use.

• Probe and lead storage and integral upright stand for use on the workbench.

• Supplied in zipped pouch Model No. with carry strap.

SEA TM102

• Designed for the automotive electrician and conforms to EN61010 CAT III 600V. • Ideal for measuring current draw from vehicle components in situ.

• Features 10mm clamp.

Model • Supplied in pouch.

No. SEA TA305

Digital Automotive Analyser/Insulation Tester - Hybrid Vehicles

• Specially designed for hybrid vehicles and conforms to EN61010 CAT III (1000V) and CAT IV (600V).

• Unlike other multimeters this unit has an insulation test function that allows testing of the insulation of the high voltage wires found on hybrid vehicles.

• Can be used as a stand-alone device or linked wirelessly with a USB interface to a PC or laptop enabling results to be graphed, saved or printed.

• Supplied with high voltage probes, thermocouple and wireless USB cable.

• The unit also has the usual functions expected on a high quality multimeter including true RMS (Root-Mean-Square) and IP67 waterproof rating.

Model No. SEA TA320

80A Automotive Current Tester Mini, Standard & Maxi Blade Fuses

Fast, accurate and safe current measurement at the fuse box.

Ideal for fault-finding on car and commercial vehicle electrical circuits.

Includes hold and peak functions for detecting current surges.

Features large LCD display with digital and graphical current read out.

Plugs straight into the vehicle’s fuse board and supplied with Mini, Standard and Maxi style blade adaptors.

• Range: 0-80A - 0-48V. Model No. • • • • •

SEA TA125

6-24V Circuit Tester

6/12/24V Circuit Tester with Test Light

Suitable for 6-24V DC circuits.

Knurled brass body with test light.

Probe tip is covered with protective brass screw cap.

Tester illuminates when voltage is present.

Model No. • Supplied with cable and alligator earth clip.

SEA AK4008

• Suitable for testing 6, 12 and 24V DC circuitry.

• Insulated, pointed probe tests through wire insulation.

• Supplied with 1.5m cable and crocodile earth clamp.

• • • •

Model No. SEA AK402

In-Line Ignition/HT Spark Tester • Tests HT supply to spark plug.

• Quick and simple fault diagnosis.

6-42V Open & Short DC Circuit Detector

• Find short and open circuits fast and easily.

• Simply attach the sender unit to the circuit and follow the wires using the detector.

• Ideal for automotive repairs.

• Suitable for all DC circuits up to 42V. Model No. • Supplied in storage case.

SEA FF400 • Powered by two 9V batteries.

6-24V Auto Probe with 4.5m Cable

Model No. SEA VS526

23pc Terminal Tool Kit • Comprehensive kit, suitable for the removal of terminals on most wiring connectors.

• Reduce time spent on, and damage to, vehicle electrical systems.

• Features soft grip handles with number identification.

Model No. SEA VS9203

0-30V Power Scope Automotive Probe

12V Digital Battery & Alternator Tester

• Fitted with 4.5m cable allowing access to the rear of the vehicle.

• Just some of the tests, which can be done quickly and efficiently, on systems from 6V up to 24V: - Cooling fan motors - Fuel pumps - Window/Sunroof motors - Relays and Lamps - Wiper motors

Model No. SEA PP1

Digital Start/Stop Battery & Alternator/Starter Tester

• One of the most advanced automotive probes on the market, with a huge range of functions for effective automotive diagnostics, making short circuits and bad earths easy to find.

• Features a scope function to visually test component signals, with the added benefit of maximum/minimum volts, frequency and duty cycle displayed.

• Allows components to be activated in situ or prior to installation.

• The fly lead allows continuity and polarity testing with a high-contrast colour LCD display giving a 7mm high read-out.

• Features an audible continuity and positive/negative voltage indicator.

• Two integral work lights.

• 6m Lead connects to the battery supply and reaches to all areas of the vehicle.

• Includes a vehicle accessory Model No. socket adaptor and SEA PP100 6m extension cable.

• Compact device which accurately tests battery, cranking and alternator.

• No heat, no sparks and no misdiagnosis.

• Just key in the battery rating from the top of the battery and results are displayed on LCD screen.

• Includes a facility to print results via PC. • No internal battery and will test batteries with a residual charge of just 8V.

Model No. SEA BT105

• Robust and simple-to-use design offers a full in-vehicle diagnosis of the vehicle battery, starter motor and alternator in seconds.

• Professional tool supports all 12V batteries including standard Lead-Acid, VRLA, GEL plus AGM and EFB found on all Start/Stop vehicles.

• The in-vehicle test mode allows diagnosis of battery health, state of charge, internal resistance, cranking voltage and a comprehensive charging system voltage at rest and under load.

• Equipped with reverse polarity protection and a battery temperature compensation feature.

• Fitted with a heavy-duty rubber Model No. protection cover.

SEA BT2011

13

Refractometer Antifreeze/Battery Fluid/Screenwash

• Suitable for synthetic antifreeze mixtures including long life OAT (Organic Acid Technology) and G13.

• Temperature corrected prism ensures accuracy.

• Eyepiece with adjustable focus.

• Supplied with pipette and storage case.

Model No. SEA VS005

10-120mm² Copper Lug Terminal Crimping Tool

• • • •

• Accurately measures the strength of battery fluid, screenwash, antifreeze and AdBlue® by measuring the refractive index of light passing through the mixture.

• Suitable for synthetic antifreeze mixtures including long life OAT (Organic Acid Technology), G13 and aqueous/urea content of AdBlue®.

• Temperature corrected prism ensures accuracy.

• Eyepiece with adjustable focus.

• Simple calibration check using distilled water.

• Supplied with pipette and storage case.

5pc Oxygen Sensor & Thread Chaser Set

Copper lug terminal tool Crimp range 10-120mm² BS Standard type terminal.

Made from SCM40 hard tool steel.

Model No. SEA AK120B

• Suitable for oxygen sensors found on most modern vehicles.

• Cut-out and slots enable sockets to be fitted over wiring harness.

• Includes two chasers for Model No. cleaning and repairing SEA SX0320 damaged threads.

14mm 12-Point 3/8"Sq Drive Spark Plug Socket with Magnetic Retainer

14mm 3/8"Sq Drive 12-Point Spark Plug Socket with Universal Joint 150mm

• Designed for use where plug clearance is tight.

• Standard depth, thin wall, Chrome Vanadium 12pt 3/8"Sq drive 14mm socket with magnetic insert to retain spark plug.

• Features a universal joint with a built-in 85mm extension for ease of access.

Model No. SEA AK6570

• Designed for use where plug clearance is tight.

• Thin wall 12pt 14mm socket.

• Magnetic insert to retain spark plug.

Model No. • Application: BMW. SEA AK6568

10pc Diesel Injector Seat Cleaner Set

• Set of seven diesel injector seat cleaners, ream, centring pilot and T-handle.

• Used to clean/decarbonise injector seats when changing injectors.

• Helps to avoid blow-back due to poorly seated injectors.

Model No.

SEA VS2055

14

Refractometer Antifreeze/Battery Fluid/Screenwash/AdBlue®

Model No. SEA VS0052

Battery Terminal Crimping Tool

• A quick and effective way of crimping battery terminals using either a hammer or vice.

• Wide throat and spring controlled punch securely holds terminal in place for added security.

• Compatible with battery terminals with a cross sectional area of 6,10, 16, 25, 35 and 50mm².

Model No. SEA AK422

Ø50-175mm Triple Leg Glaze Breaker 75mm Medium Stones

• For removal of heat glaze and carbon deposits on cylinder walls.

• Fitted with 75mm, medium grade cutting stones and suitable for cylinders up to Ø175mm.

• Range collar adjusts arm travel between Ø50mm and Ø100mm or Ø100mm and Ø175mm.

• Adjustable spring tension gives Model finish control.

No. SEA VS162

20pc Cleaning & Decarbonising Brush Set

• Ideal for cleaning and decarbonising areas with limited access, especially injector apertures before refitting.

• Supplied in sizes from Ø9-19mm in brass, nylon and steel.

• Features quick release extension bar for increased reach.

Model No. SEA VS1800

Battery Fluid Filler

Battery Fluid Tester - Tube Type

• Professional battery hydrometer.

• Float gauge and thermometer built-in.

• Fluid transfer tool suitable for battery top-up and level adjustment of coolant and screen wash.

Model No. • Spout Length: 130mm.

SEA AK4124 • Bulb Capacity: 150ml.

4-Way Battery Post & Terminal Cleaner

• Wire brushes remove corrosion build-up on battery posts and terminals for improved electrical contact.

Model No. SEA AK417

Battery Terminal Puller

• Removes heavy corrosion build-up on battery posts and terminals for improved electrical contact.

• Features clamp reamer and terminal scrapers.

Model No. SEA AK418

Model No. SEA AK414

Battery Post & Terminal Cleaner

• Mini puller with spring loaded jaws designed for removal of corroded battery clamps from terminals.

• Suitable also for removal of small gears, pulleys and bearings.

Model No. SEA AK419

6/12V Battery Drop Tester

50-160mm Dial Bore Gauge

• Precision mechanism with Ø55mm dial and locking rotating bezel, offering an accurate method of measuring a bore or detecting a taper or ovality.

• Measuring Range: 50-160mm.

• Will indicate the deviation from set size by up to 3mm with an accuracy of 0.01mm.

• Probe body, dial indicator, anvils and spacer rings are also included.

Crankshaft Rotator for DAF 1/2"Sq Drive

Battery Carrier

• Load applied by internal switchgear - no sparking!

• Applies load across cells and measures output on meter.

• Accurate indication of battery voltage and faulty Model No. or short circuited cell.

SEA BT91/7

• Designed to rotate crankshaft on DAF commercial vehicles via flywheel ring gear.

• Tubular steel handle with comfort grip.

• Enables fast, safe handling of batteries.

• Fully adjustable for battery size.

Remote Action Hose Clip Tool

• Long reach tool designed for awkwardly positioned tag-type hose clips.

• Flexible cable and compact head help operation in confined spaces.

• Features ratchet action and vinyl dipped handles for comfort and close control.

Model No. SEA VS1663

Model No. SEA DBG5010

Model No. SEA BT91/9

2pc Hose Clip Pliers Set

• Heavy-duty construction with PVC dipped handles for added comfort and grip.

• Special ‘V’ slot and cross slot jaws for installation and removal of tag and wire type hose clips.

• Pliers with ratchet locking mechanism for ease of use on lower radiator hoses.

• Swivel jaws allow use where Model No. access is confined.

SEA VS1665 • Length: 220mm.

Model No. SEA CV002

Crankshaft Rotator - Scania 1/2"Sq Drive

• Chrome Vanadium steel with a phosphate finish.

• Designed to rotate the crankshaft on Scania commercial vehicles.

Model No. SEA CV011

15

CVJ Boot Installation Tool

CVJ Boot Tool - Air

• Innovative tool saves time, money and frustration.

• Installs CVJ boots without removing drive shafts from the vehicle or the CV joint from the drive shaft.

• No effort and no mess!

• Save on labour time by up to 70% and prevent damage to CV joint.

• Composite body with simple control valve, works from standard workshop air supply.

• While fitting boot the tool can be removed from the air line when pressurized (arms open) and will maintain pressure until the release button is pressed.

• Suitable for cars and light commercial vans.

• Composite cone.

• Enables installation of CVJ boot without splitting drive train.

• Suitable for use with all Sealey CVJ stretch boots.

Model No. SEA BSL103

Ø56-116mm Universal Stretch CVJ Boot EU

CVJ Boot Ear Clamps - Packs of 25

• Universal CVJ boot made from high quality neoprene material suitable for use with air operated boot installation tools.

• Supplied with fitting kit including clips and cutting guide.

• Suitable for most car and car derived van applications.

• Stainless steel, single ear, low profile CVJ boot clamps.

• Manufactured to DIN 1.4301.

Model No. SEA CV96EU

Model No.

Size

SEA CVC01

Ø19-40mm

SEA CVC02

Ø50-110mm

Thread Repair Master Kit

Model No. SEA VS705

CVJ Removal Tool

• Quickly removes the CV joint from the drive shaft without damaging the joint, and keeps hands free for releasing retaining circlip.

• Reduces risk of damage to transmission.

• Saves on labour time and Model No. suitable for most vehicles.

SEA VS710

Thread Inserts

• Suitable for five common sizes of thread.

• Creates a stronger internal thread in soft metals.

• Ideal for repairing damaged or stripped internal threads.

• Protects tapped threads against wear and damage.

• Includes drill bits, thread taps, insert installation and lug breaking tools.

• Supplied in metal storage case.

Model No. SEA TRMK

Model No. TRM6R

Model No.

Size

SEA TRM6R

M6 x 1mm

SEA TRM8R

M8 x 1.25mm

SEA TRM9R

M9 x 1.25mm

SEA TRM10R

M10 x 1.5mm

SEA TRM12R

M12 x 1.75mm

Thread Repair Kits d

Model No. • Creates a stronger internal thread in soft metals.

• Ideal for repairing damaged or stripped internal threads.

• Protects tapped threads against wear and damage.

• Includes drill bit, thread tap, insert installation and lug breaking tool.

• Supplied with three different lengths of thread insert.

Size

Thread Lengths

SEA TRM6

M6 x 1mm

4, 6, 9 (5 of each)

SEA TRM8

M8 x 1.25mm

6, 9, 12mm (5 of each)

SEA TRM9

M9 x 1.25mm

7, 14mm (3 of each), 11mm (x4)

SEA TRM10

M10 x 1.5mm

7.5, 15mm (3 of each), 11mm (x4)

SEA TRM12

M12 x 1.75mm

9, 18mm (2 of each), 14mm (x4)

SEA TRM14

M14 x 1.25mm

10, 21mm (1 of each), 16mm (x3)

Mo

9

RM

.T

o el N

M8 x 1mm Thread Insert for VS311 Pack of 5

M10 x 1mm Thread Insert for VS311 Pack of 5

M10 x 1.25mm Thread Insert for VS311 Pack of 5

• Thread inserts for Model No. VS311.

• Thread inserts for Model No. VS311.

• Thread inserts for Model No. VS311.

Model No. SEA VS311.01

16

Model No. SEA VS311.02

Model No. SEA VS311.03

1000W Induction Heater

• • • • • •

32 Blade Feeler Gauge - Dual Marked

Mobile induction heater for fast heat delivery.

Install appropriate coil and place over or around ferrous metal.

Ideal for loosening stubborn and seized fixings.

Supplied with induction pad for plastic trim/sticker removal.

Induction element delivers high heat fast and effectively.

Contents: Direct Coil; Ø20, Ø32mm, Pad Coil; Ø55mm, U-Coil; 430mm, Flex Coil; 830mm.

• • • • •

Model No. SEA VS240

Imperial graduated 32 blade feeler gauge.

Sizes: 0.0015" to 0.035" (0.038 to 0.889mm).

Dual marked in Imperial and Metric.

Includes 0.010" brass blade.

Blade dimensions 90 x 13mm.

Model

No. SEA S0514

13 Blade Feeler Gauge - Metric

2300W Induction Heater Rapid Heat • Mobile induction heater for fast heat delivery.

• Install appropriate coil and place over or around ferrous metal.

• Ideal for loosening stubborn and seized fixings.

• Supplied with special dent induction block for panel expansion and induction pad for plastic trim/sticker removal.

• Contents: Direct Coil; Ø20mm, Direct Coil; Ø30mm, Side Coil; Ø20mm, Side Coil; Ø30mm, Pad Coil; Ø55mm, Flex Coil; 740mm, Induction Block; Ø32mm x 45mm, Pad Coil; Ø37mm.

• Supplied in storage case.

• Metric graduated 13 blade feeler gauge.

• Sizes: 0.05 to 1mm.

• Blade dimensions 95 x 10mm.

Model No. SEA VS250

Model No. SEA S0517

Cooling System & Cap Testing Kit

Cooling System Filler

• Capless cooling system tester uses an inflatable bladder to seal the pressure head to the radiator or header tank.

• Bladder system can be used on both screw and bayonet fittings and seals 90% of cars and light commercial vehicles straight out of the box.

• Also suitable for motorcycles, off-road and marine applications.

• Supplied with set of double end Model No. adaptors enabling testing of SEA VS0031 cooling system pressure caps.

Propylene Glycol Antifreeze Tester Twin-Rotor

• Eliminates the introduction of bubbles and air-locks into the cooling system and dramatically reduces system filling time.

• No more time-consuming system bleeding.

• Reduces fluid waste and messy spills.

• Automatically conducts system leak test.

• Low profile design broadens application range especially for use on MPVs where lower windscreen lip might obstruct other tools.

• Simple operation requires workshop air supply and does not require fiddly interchange of vacuum and fluid hoses - as found on other versions of this tool.

• Can be used in conjunction with Sealey cooling system pressure caps as an alternative way of connecting to the coolant Model No. reservoir.

SEA VS0041 • Supplied with 1.3m fluid hose.

• Tests propylene glycol antifreeze mixtures.

• Features a temperature compensation rotor that automatically adjusts the reading regardless of the coolant temperature.

• Freeze protection level is indicated on the scale in degrees Celsius.

Model No. SEA VS4121

Ethylene Glycol Antifreeze Tester Disc Type

Ethylene Glycol Antifreeze Tester Dial Type

Battery Fluid Tester Dial Type

• Checks condition of coolant antifreeze, hot or cold.

• Protection level is indicated by the number of discs floating in the sample.

• Tough, virtually unbreakable, Model No. plastic body.

• Tests ethylene glycol strength with engine hot or cold.

• Composite body and rubber bulb for workshop durability.

• Tests 6, 12 and 24V batteries.

• Composite body and rubber bulb for workshop durability.

SEA AK4120

Model No. SEA AK409

Model No. SEA AK410

17

Oil Drain Plug Thread Repair Set

21pc 3/8"Sq Drive Oil Drain Plug Key Set

d

Mo

• Ideal for repairing sump, gearbox and differential drain plug threads.

• Used to tap the damaged thread slightly oversize, then fit a new drain plug and washer.

Model No.

15

S6

.V

o el N

Tap Size

SEA VS613

M13 x 1.5mm

SEA VS615

M15 x 1.5mm

SEA VS617

M17 x 1.5mm

• Comprehensive set of Chrome Vanadium steel keys with sliding T-bar.

• Suitable for sump plugs on engine, gearbox and back axle.

• Contents: Square Male; 7, 8, 10, 11, 12, 13, 14mm, 5/16", 3/8", Square Female; 10mm, Hex; 8, 9, 10, 12, 13, 14, 17mm, Triangle; 10mm (PSA), Security Spline; M16 (VAG), TRX-Star**; T45 (Vauxhall/Opel), 3/8"Sq Drive Sliding T-Bar.

Drain Plug Thread Repair Set

Oil Drain Plug Master Thread Repair Set

• Superb for repairing sump, gearbox and differential drain plug threads.

• Used to tap the damaged thread slightly oversize, then fit a new drain plug and washer (supplied).

• Set is suitable for the most popular threads used on cars and light commercial vehicles.

• Tap Sizes: M13 x 1.5, Model No. M15 x 1.5, M17 x 1.5, SEA VS660 M20 x 1.5mm.

• Comprehensive thread repair kit ideal for repairing sump, gearbox and differential drain plug threads.

• Used to tap the damaged thread slightly oversize, then fit a new drain plug and washer (supplied).

• Set is suitable for the most popular threads used on cars and light commercial vehicles.

• Tap Sizes: M13 x 1.25, M13 x 1.5, M15 x 1.5, M17 x 1.5, M20 x 1.5, M22 x 1.5mm.

Oil Filter Crushing Unit

Model No. SEA AK6586

Model No. SEA VS661

Sump plugs

Model No. Model No. VS660.06

Model No. VS660.07

Tap Size

SEA VS660.06

M17

SEA VS660.07

M15

8-in-1 Oil Drain Plug Wrench

• The right size drain plug key always in your hand.

• Eight Popular sizes covered in one tool.

• Sizes: Hex; 10, 12, 14, 17mm, Square; 3/8", 1/2", 8, 10mm.

• Suitable for drain plugs on engine, gearbox and back axle.

22mm Mechanic’s Mat Set EVA

• Used in conjunction with a press, this unit crushes filters up to Ø115mm.

• Oil and sludge drains into a suitable container (not included).

• Crushing filters minimises the cost of disposal of hazardous waste by volume.

• Ram extension allows two-stage crushing of large filters without repositioning press table.

• Suitable for Ø38mm(1.5") press rams. Optional adaptors enable use with Ø50mm and Ø60mm rams.

• Internal Diameter: 130mm, Model No. Effective Internal Height: SEA OFC1 175mm.

18

Quality 22mm EVA mats ideal for the busy mechanic.

Oil and water resistant.

Set comprises full length and kneeler mats.

For use on workshop floors when working on wheels, brakes, tyres and exhausts.

• Also ideal for roadside repairs.

• Sizes (L x W x D): Model No. Full Length Mat; 980 x 380 x 22mm, SEA S08561 Kneeler Mat; 450 x 215 x 22mm.

• • • •

Model No. SEA VS650

Ø64.5mm Oil Filter Cap Wrench 14 Flutes - Toyota

Ø64.5mm Oil Filter Cap Wrench 14 Flutes - Lexus/Toyota

Oil Filter Cap Remover Ford/ Jaguar/Citroen/Peugeot 2.0D/2.2D Diesel

• Cap type oil filter wrench.

• Crowned top provides extra leverage points for removing stubborn oil filter housing caps.

• Aluminium alloy material minimises risk of damage to filter housing.

• Cap type oil filter wrench.

• Crowned top provides extra leverage points for removing stubborn oil filter housing caps.

• Aluminium alloy material minimises risk of damage to filter housing.

• Suitable for removing the cap from the oil filter housing on Ford, Citroen, Peugeot 2.0D/2.2D HDi/TDCi diesel engines (DW10C, DW12C) and Jaguar XF 2.2D from 2012 onwards.

• Allows access to the hard-to-reach 27mm hex located on the filter cap.

• Use with 1/2"Sq drive wrench.

Model No.

Model No. SEA VS7111

Model No. SEA VS7112

SEA VS7200

Oil Filter Strap Wrench Ø60-140mm Capacity

150mm Strap Wrench

1/2"Sq Drive Oil Filter Chain Wrench Ø135mm Capacity

• Satin finished, drop-forged steel body with hanging hole.

• Reinforced, rubberised strap.

• Suitable for removing and installing oil filters as well as many other applications.

• Adjustable strap fits filters up to Ø150mm.

• Features soft grip handle for added comfort.

• Satin finished carbon steel body with 1/2"Sq drive for use with ratchet wrench.

• May also be used with a 20mm spanner.

• Heavy-duty chain.

• Drive: 1/2"Sq

Model No. SEA AK6404

Model No. SEA AK6407

3/8" & 1/2"Sq Drive Oil Filter Claw Wrench 63-103mm Capacity

Self Adjusting Oil Filter Pliers Angled

• Also suitable for use with a 21mm spanner.

• Claws grip filter tighter as more torque is applied.

• 30° Angled head allows access to previously impossible to reach areas.

• Jaws auto-adjust with one hand operation.

• Layered steel construction for Model No. added strength.

SEA AK6421 • Capacity: Ø60-120mm

Model No. SEA AK642

Oil Filter Wrench Band Type Ø65-105mm Capacity

• Band type filter wrench.

• Steel strap with heavy-duty cast body and control knob.

• Removes filters with minimal risk of damage.

Model No. SEA AK644

600mm Engine Dipstick - Audi

• Designed to measure the engine oil levels on Audi vehicles fitted with electronic oil level systems.

• Can also be used to calibrate the driver’s instrument panel.

• Will also check the engine oil level on Audi; A4/A5 3.2 Model No. 6-cylinder engines.

SEA VS600ED

Model No. SEA AK641

3/8" & 1/2"Sq DriveOil Filter Claw Wrench Ø65-110mm Capacity

• Satin chrome finish steel construction with 1/2" & 3/8"Sq drives.

• Also suitable for use with a 21mm spanner.

Model No. • Claws grip filter tighter as SEA AK643 more torque is applied.

Vauxhall/Opel Oil Filter Drain Funnel

• Designed to reduce the amount of time taken to replace the engine oil filter on Vauxhall/Opel vehicles fitted with the B20 diesel engine.

• Once the Drain Funnel is located, oil draining from the oil filter can be channelled into a suitable receptacle.

• Time saving tool as it eliminates oil spillage onto vehicle chassis Model No. and components during filter SEA VS5053 change.

19

200ml Oil & Brake Fluid Inspection Syringe

• Multipurpose syringe with Viton® seal, ideal for the transfer of oils/fluids to and from vehicle components such as brake master cylinders, oil filter housings, power steering reservoirs, differentials and gearboxes.

• Translucent body allows easy inspection of oils and fluids.

Model No. SEA VS404

1.5L Oil Inspection Syringe

3L Transmission Oil Filling System

• Multipurpose syringe with Viton® seal, ideal for the transfer of oils/fluids to and from vehicle components such as gearboxes and differentials.

Model No. • Translucent body allows SEA VS405 easy inspection of contents.

Pocket Brake Fluid Tester

• Pump operated oil dispensing unit with a three litre capacity.

• Supplied with five multipurpose and three vehicle specific automatic transmission Model No. fluid adaptors.

SEA VS70095 • Features a fluid control and depressurising valve.

Brake Fluid Tester - Boil Test

• Integrated circuitry checks moisture content of fluid by measuring the electrical resistance and comparing it with acceptable limits.

• Easy calibration check using water.

• Five LED read-out.

• Just switch on and insert probe for immediate result.

• Works on all grades of brake fluid.

Model No. • Powered by one AAA SEA VS0274 battery (supplied).

• The approved method of testing the water content of brake fluid.

• Just 3% of moisture can lower the brake fluid boiling point by over 100°C. • The best way to detect this small water content is to measure the boiling point of the fluid.

• The unit incorporates a heater element, LCD display and a power lead for use on 12V DC power supplies.

• Works on DOT 3, 4, 5 and Model No. 5.1 specification fluids.

SEA VS0275

21pc Brake Piston Wind-Back Tool Kit

Brake Piston Wind-Back Tool with Double Adaptor

• Double end tool.

• Enables retraction of the piston on rear brake calipers allowing new brake pads to be installed.

Rear Brake Piston Wind-Back Adaptor VAG • Adaptor enables retraction of the piston on rear brake calipers when used in conjunction with a traditional wind-back tool with a two-pin adaptor mounting.

• Applications: Model No’s. VS0211, VS0240, VS0243, VS028, VS0282, VS0285, VS0286, VS0287.

Model No. • Three-pin design suitable SEA VS02821 for VAG vehicles.

Folding Mechanic’s Work Mat

• Suitable for push-back and wind-back brake pistons.

• Includes left and right-handed thrust bolt assemblies, reaction plate, hex bits and adaptors and includes the 3-pin VAG adaptor.

Model No.

SEA VS0282

20

• Flexible work mat with two handles for portability.

• Durable composite cover that resists stains and fluids.

• High density padding for added comfort.

• Ideal for working on cold garage floors Model No. and for roadside repairs.

SEA VS858 • Open Size: 1220 x 444 x 38mm.

Model No. SEA VS024

Automatic Brake & Clutch Bleeder

Pneumatic Brake & Clutch Pressure Bleeder Kit

• Fast, easy and effective bleeding of brakes and clutch using air from tyre.

• Innovative design incorporates valve for control of air pressure, extra long air hose for use with larger vehicles and magnetic reservoir base to prevent accidental spillage.

• Suitable for use with ABS systems.

• Supplied with range of Model No. common adaptors.

SEA VS0205

• Low pressure tank (20-40psi) can be pre-charged with compressed air, making the unit fully portable.

• Large reservoir (5L) means reduced risk of running the system dry during bleeding process or complete fluid change.

• Suitable for use on ABS systems.

• Features a long delivery hose (3.7m) for operation with a low level ramp, and long reach handle for easy mobility.

• Supplied with a range of European, Japanese and US vehicle adaptors.

Model No. SEA VS0204

Gravity Brake Bleeder Kit

Brake & Clutch Bleeding System

1L Pneumatic Vacuum Brake Bleeder

• Ingenious patented design maintains the fluid level in the vehicle’s brake or clutch fluid reservoir during the bleeding process.

• Uses the standard 500ml brake fluid bottle in which fluid is supplied, reducing the possibility of contamination.

Model No. • Fast, simple to use and features on/off flow valve.

SEA VS0209

• Reservoir holds 2.5L of hydraulic fluid - flush the entire system with one fill, without the risk of running the reservoir dry.

• Pressure range makes unit suitable for use with ABS systems.

• Fitted with Ø45mm cap with 90° angled connector which is suitable for Model No. most European models.

SEA VS820

• The simple way to bleed hydraulic brakes.

• One-man operation.

• No special reservoir caps required.

Model No. • Uses regular 90psi air SEA VS020 supply.

5pc Brake Caliper Slogging Wrench Set

Pneumatic Brake Bleeder

• Used for installing and removing the brake caliper bolts on commercial vehicles.

• Designed with a 3/4"Sq drive for use with a torque wrench.

• Formula for calculating the correct effective length lasered on wrench.

• Two striking faces for access and aiding in loosening of bolts.

• 3/4"Sq Drive TRX-Star*; E18, E20, E24 and Bi-Hex (12pt); 24, 26mm.

• TRX-Star* Applications: E18 - Man TGL/TGM, E20 - Man TGL/TGM, E24 - Man TGA/TGS/TGX. • Bi-Hex (12pt) Applications: 24mm - SAF, 26mm - DAF XF/XF95/XF105/XF106.

• One-person professional pneumatic brake bleeding tool.

• Pressure range makes unit suitable for use with ABS systems.

• Reservoir holds 3 litres, plenty to flush a whole system without the risk of running dry.

• Two drainage method options allow you to drain brake fluid via the brake caliper with the bottle option for replenishing, or brake reservoir pressurising for full brake bleed.

Model No. SEA CV212

4-in-1 Cylinder Hone Kit

Model No. SEA VS0215

• Four cylinder-honing tools in one kit covering 18mm to 89mm cylinder bores.

• Suitable for honing and de-glazing car brake and clutch cylinders plus motorcycle, outboard and lawnmower engine cylinders.

• Adjustable honing pressure and Model No. flexible drive shaft.

SEA VS029

21

3pc Seal Puller Set

14pc Stud Hub Cleaner

• Suitable for the safe removal of drive and transmission oil/grease seals and O-rings, without damage to seal or surrounding casting.

Model No. SEA VS8000

• • • • •

Removes surface dirt and corrosion on hubs fitted with studs.

Ideal for preparing wheels, hubs and brake discs or drums for re-assembly.

Cleaning discs fit over wheel studs.

Use with power drill or air impact wrench.

Model No. Supplied with 1/2"Sq drive adaptor.

SEA VS8002

Brake Pipe Bending Tool

• Nylon components with steel main shaft.

• Fits 90% of cars and light vans up to 5tonne gross (not suitable for vehicles with double plate clutches).

• Supplied with three different sized expanding collets.

Model No. SEA VS5057

• Provides two sizes of bend for accurate and safe shaping of automotive brake pipes without risk of kinking.

• Fitted with a 6mm hex slot for ease of holding/turning.

Model No. SEA VS0375

Master Locking Wheel Nut Removal Set

• Simple to use master kit capable of removing practically any locking wheel nuts.

• Kit includes shroud, which protects the wheel against any damage.

• Replacement disposable blades available, Model No. SX299DB (Pack of 10).

Model No. SEA SX299

Blade C for SX299 Pack of 10 • Designed for use on McGard locking wheel nuts.

• For use with Model No. SX299.

Model No. SEA SX299DB

22

• Pair of clamps designed to aid in the shaping and bending of brake pipes.

• Small body is suitable for on-vehicle applications.

• For use with 4.75mm(3/16") and 1/4" brake pipe.

Model No. SEA VS0357

Brake Pipe Bender

Universal Clutch Alignment Tool

• Vice mounted brake pipe shaping tool, designed for use on automotive applications.

• Duel stepped sections allow pairing of pipes for correct curvature for uniformed alignment to vehicle.

• Suitable for 3/16" (4.76mm) cupronickel, copper and steel pipe.

• Diameter: 21, 31.5, 46.5, 61.5, 76.5mm.

Hand-Held Brake Pipe Bender

2pc Brake Pipe Clamp Set

Model No. SEA VS010

Steering Rack Knuckle Tool

• Compact design for bending automotive brake pipes without crushing the pipe walls.

• Rigid construction makes it suitable for steel pipes.

• Will bend Ø3mm(1/8"), Ø4.75mm(3/16") and Model No. Ø6mm(1/4") pipe up to 90°.

SEA VS5055

Digital Tyre Pressure & Tread Depth Gauge with LED

• Suitable for the fast and easy removal of the steering knuckle.

• Fits racks with hex drive, two flats and round ends.

• Ideal for vehicles with limited access and avoids the need to remove the rack assembly.

• Suitable for steering rack Model No. knuckles with a diameter of 33 to 41mm.

SEA VS4000

• 3-in-1 Pocket size tyre gauge with removable keyring.

• Simple one-button operation with easy-to-read large backlit LCD display.

• Tread depth function gives high accuracy readings in mm or inches.

• Simple-to-read traffic light system for wear indication.

• Precise tyre pressure readings can be displayed in bar, psi, kPa and kg/cm².

• Equipped with a bright LED. • Auto power-off feature.

• Powered by 2 x CR2032 (supplied).

Model No. SEA TSTPG12

Brake Pad Thickness Gauge • Measures the brake pad lining on the vehicle without removing the road wheel.

• Slim design enables the tool to locate the rear of the pad backing plate, allowing the probe to measure the distance between the underside of the backing plate and brake disc.

• Suitable for both internal and external brake pads.

• Features calibration line, plus minimum 1.5mm pre-MOT check mark.

• Range: 1.5-13mm.

• Designed for brake pads that have a normal 6mm thick backing plate (Class IV, V).

Model No. SEA VS058

4pc Hose Pinch Tool Set • Light and compact steel alloy construction for ease of use where space is limited.

• Rounded jaw edges prevent damage to internal hose reinforcements.

• Suitable for use on fuel, vacuum and brake hoses.

Model No. SEA VS0301

Tyre Inflator with Clip-On Connector

Tyre Inflator with 0.5m Hose & Twin Push-On Connector

Digital Tyre Inflator with 0.5m Hose & Push-On Connector

• Composite body and dial type gauge with rubber protector.

• Range: 0-10bar/0-145psi.

• Fitted with 500mm rubber hose and single clip-on connector.

• Manufactured to comply with EN 12645.

• Aluminium body with rubber bumper.

• Linear pressure scale, dual calibrated in psi and bar, with parallax correction.

• Range: 0-9.6bar(0-140psi).

• Die-cast aluminium body with large rubber bumper, backlit LCD digital display and battery level indicator.

• Auto power off after 8 seconds and auto power on once pressure is sensed, or air inflation starts.

• 0.5m Flexible hose fitted with Model No. 240mm push-on air connector.

Model No. SEA SA9302

Model No. SEA SA371

Tyre Inflator with Clip-On Connector

Jumbo Tyre Inflator with Clip-On Connector • Composite body and dial type jumbo gauge with rubber protector.

• Calibrated in bar and psi.

• Fitted with 400mm rubber hose and single clip-on connector.

• Die-cast body and dial type gauge with rubber protector.

• Range: 0-10bar(0-145psi).

• 1/4"BSP Air inlet.

Model No. SEA SA924

Model No. SEA SA9303

Tyre Tread Depth Gauge Pocket Type

Digital Tyre Tread Depth Gauge

• Chromed steel body with pocket clip.

• Scale from 0 to 25mm in 1mm(0-1" in 1/32") graduations.

Model No. SEA TST/DGE

• Tough composite sliding gauge.

• 10mm High figures in LCD display.

• Metric and Imperial calibration with conversion between the two.

• Range: 0-25mm(0-1").

• Zero setting control allows for comparative measurement.

Model No. SEA VS0564

Four-Wheel Laser Wheel Aligner

SEA SA374

Clip-On Connector for Tyre Inflators 1/4"BSP Fitting

• Compatible with many brands of tyre inflator fitted with a 1/4"BSP male connector on the end of the hose.

• Suitable for Sealey Model No’s SA39, SA371, SA372, SA374, SA375, SA397, SA399, SA37/93 and SA37/95.

Model No. SEA SA37/C

Tyre Valve Core Tool

• Used for removal and installation of the core from a wheel valve.

• Suitable for motorcycles, cars and commercial vehicles.

Model No. SEA TST/VCT

Airbag Test Resistor Set

• Assists in the diagnosis of airbag units and seat belt pretensioners.

• Connect in place of an airbag or seat belt pretensioner unit to test for component failure.

• Contains a two ohm resistor and two probe leads.

• Always follow manufacturers instructions when testing SRS systems and components.

Model No.

SEA ABTR01

Steering Wheel Level

• Fast, simple and accurate alignment of both front and rear wheels.

• Optimises vehicle performance and set up after installation or modification of steering and suspension components.

• Simple and fast to use, it is ideal for the busy professional workshop and has a fast return on investment - potentially adding value to every steering or suspension job.

• This fully portable kit is also ideal for track-day set up for the enthusiast.

• Works on practically all cars and light commercials with rim diameters between 330mm(13") and 560mm(22").

• Supplied with steering wheel clamp, wheel turn plates and wheeled storage rack.

• Supplied with comprehensive Model No. operating instructions.

SEA GA70

• Used to level the steering wheel before locking into position, prior to checking/adjusting the front wheel alignment.

• Ideal for use with Four-Wheel Laser Aligners such as Model No. GA70.

• Self-retaining and centring using a spring loaded mechanism.

• Features a level bubble to show horizontal position.

• Suitable for steering wheels with an internal diameter of between Model No. 270mm and 340mm.

SEA GA460

23

85mm Impact Socket Commercial 1"Sq Drive

65mm 3/4"Sq Drive 12-Point Impact Socket

3pc Coil Spring Compressor with Safety Hooks

• Carbon steel, hardened lead screws and cast jaws with safety hooks to prevent accidental release of spring under compression.

• Maximum load per set of three clamps 1650kg.

• Chrome Molybdenum, drop-forged, 6-point impact socket.

• Phosphate finish for greater corrosion resistance.

• Ideal for use with air Model impact wrenches.

• Forged and heat treated Chrome Vanadium steel impact grade sockets, chemically blackened for corrosion resistance.

• Malleable steel makes these sockets suitable for use with Model No. either hand ratchet wrenches or air impact wrenches.

SEA SX0150

1/2"Sq Drive 4-Way Wheel Brace

2pc Coil Spring Compressor

1000kg Hydraulic Coil Spring Compressor

• Hardened carbon steel lead screws and cast jaws.

• Wrap-over coil claws for extra safety.

• Suitable for use where space under wheel arch is limited.

• Use with 1/2"Sq drive wrench.

• Maximum Jaw Opening: 244mm.

Model No. • Maximum Capacity Per Pair: SEA AK3841 1000kg.

• Equipped with two pairs of spring yokes with plasticized covers to prevent slippage and damage to springs.

• Suitable for springs from 80mm ID to 165mm OD.

No. SEA CV085

• Forged construction with polished mirror finish.

• Features three popular size wheel nut sockets and 1/2"Sq drive adaptor for standard sockets.

• Socket Sizes: 17, 19, 21mm.

Model No. SEA AK2093

2000kg Hydraulic Coil Spring Compressing Station with Gauge

1500kg Hydraulic Coil Spring Compressing Station

Model No. SEA AK384

Model No. SEA VS7011

Coil Spring Compressor Restraint System

• Safety restraint system designed for use with Model No’s RE231, RE2311 and RE232 Coil Spring Compressors.

• Quickly installed and fast and simple to operate in use.

• N.B. Coil Spring Compressor not included.

• Foot operated hydraulic unit, with gauge showing force applied to the spring under compression.

• Supplied with three pairs of different sized interchangeable yokes, for a wide range of vehicle applications.

• Fitted with plastic yoke protectors that protect the spring coating from damage, which can invalidate the vehicle manufacturer’s guarantee.

• Suitable for springs from Model No. Ø87mm to Ø202mm.

SEA RE2311

24

• 1500kg Capacity foot operated hydraulic unit.

• Quicker and easier than using ratchet driven spring compressor.

• Plastic coated yokes reduce the risk of spring slippage/damage.

• Suitable for springs from Ø80mm to Ø175mm.

Model No. SEA RE231

Model No. SEA RE23RS

Hydraulic Bead Breaker

5L Measuring Jug

5L Measuring Jug with Flexible Spout

• Transparent measuring jug with wide base for extra stability.

• Transparent measuring jug with removable flexible spout. Wide base for extra stability.

Model No. SEA VS562

Model No. SEA VS563

127kg Wheel & Tyre Handling Dolly

• Hydraulic action, suitable for breaking beads on commercial and agricultural tyres.

• Use in conjunction with Model No. hydraulic pump and hose SEA TC966 (not included).

4-Way Wheel Brace

• Forged construction with hot forged sockets and baked finish.

• Socket Sizes: 17, 19, 21, 22mm.

Model No. SEA AK2090

Air Knife

• • • • • • •

Quickly and easily cuts windscreen bonding.

Safety throttle prevents inadvertent starting.

Speed control by integral regulator.

Exhaust ducted away from work and operator.

Supplied with offset straight blade and hex key.

Wide range of optional blades available.

Air Pressure/Consumption: 90psi(13.2cfm).

Model No. SEA TH002

• For commercial sized wheel and tyre removal/installation.

• Fork Centres: 535mm.

Heavy-Duty Wiper Arm Puller

• Heavy-duty construction with locking feature allowing secure fastening to the wiper arm before commencing pull.

• With swivel mounted thrust bearing and tommy bar, the tool releases the most stubborn wiper arms.

• Also suitable for battery terminal and alternator bearing removal.

• Maximum Opening: 28mm.

• Maximum Collar Size: 43mm.

Model No. SEA WK025

Model No. SEA VS807

25

Wire Grip Handles Pair

• Reinforced composite ABS handles with heat treated, chromed steel shafts.

• Suitable for use with Model No. windscreen cutting wire.

Windscreen Cutting Wire Braided

Windscreen Cutting Wire Square

• Braided stainless steel wire suitable for use with wire grips.

• Use a sawing action to cut through the urethane bond.

• Length: 22.5m.

• Becoming more popular than braided wire.

• Stainless steel square profile has four cutting edges.

• Fast and easy cutting of urethane bond even in cold conditions.

Model No. • Length: 22.5m.

Model No. SEA WK0513

SEA WK0512

12pc Trim & Upholstery Tool Set

• Manufactured from resilient nylon to minimise panel damage and marking.

• Includes eleven trim and upholstery tools, plus trim Model No. hammer in a heavy-duty SEA RT12KIT storage pouch.

14pc Windscreen Removal Tool Kit

• Durable lightweight design delivers on quality and finish.

• Complete tool kit for the removal of bonded and rubber seals.

• Designed for the professional.

Model No. SEA WK14

Universal Press Support Block

26

Adjustable Press Support Plate

• Designed to be used with a standard workshop press.

• Multiple threaded holes in aluminium base plate enable the support bars to be installed in virtually any position, allowing the bearing or bush to be positioned horizontally.

Model No. • Includes a packing block for SEA VS7036 added versatility.

Remote Action Button Clip Pliers

• Designed to be used with a standard workshop press.

• Adjustable diameter and six interchangeable support legs provide quick alignment of hub or suspension frame for secure and level pressing.

• Ideal when removing and installing wheel bearings and bushes.

Model No. • Operating Diameter: Ø78-100mm.

SEA VS7037

2pc Lightweight Front Seat Protector Set

• Long reach tool designed for awkwardly positioned button clips found on fuel circuits, power steering, brake fluid, air conditioning and gear boxes.

• Flexible cable and compact head help operation in confined spaces.

• Length: 650mm.

Model No.

SEA VS551

Headlight Restoration Kit • Three-stage headlight restoration kit designed to eliminate the worst cases of headlight degradation, yellowing, oxidation and scratches.

• Includes everything needed to restore the cloudiest lenses.

• Get great results on most plastic lenses, such as tail lights, trailers, boat windows, helmet visors, motorcycle windscreens, snowmobiles and more.

• Improves visibility and safety.

• One kit is intended to restore two headlight lenses.

• Contents: Sanding Discs; P800 (x2), P1200 (x2), P2000 (x2), M10 Male to Female Adaptor, 40g Polishing Paste (x2), 3ml Protection Liquid (x2), 3m x 20mm Masking Tape, Backing Pad M10 Female Thread, Sponge Discs; Orange, White.

SEA WK0514

• Set includes two reuseable front seat covers.

• Manufactured from water resistant lightweight nylon.

• Ideal for protecting the vehicle’s interior from dirt, grease and oil, as well as food and drink spills.

• Suitable for most cars and light commercial vehicles.

• Can be fitted to seats with or without airbags.

Model No. SEA CSC5

4pc Mini Hook Set

Model No. SEA HRK01

• Chrome finish shafts with knurling for fingertip precision.

• Suitable for removal of bushings, cotter-pins, O-rings and seals.

• Classic style handle.

• Overall Length: 125mm.

Model No.

SEA AK521

Sanding Block

• Accepts 100mm wide abrasive strips.

• Comfortable contoured grip.

• Interlocking grip and base separate completely for very simple and fast abrasive changes.

Model No. SEA SB66

42pc 3/8" & 1/2"Sq Drive TRX-Star*/Hex/ Spline Bit Set

• Manufactured from Chrome Vanadium steel.

• Long and short TRX-Star*, spline and hex bits.

• Includes 3/8" and 1/2"Sq drive to 10mm hex Chrome Vanadium steel bit adaptors.

• Convenient high impact Model No. storage case presents bits at an angle for easy selection.

SEA AK219

74pc 3/8" & 1/2"Sq Drive TRX-Star*/ Security TRX-Star*/Hex/Ribe/Spline Bit Set

• Manufactured from Chrome Vanadium 6150 steel.

• Contents: TRX-Star* Bits; T20, T25, T30, T40, T45, T50, T55, T60 (1 each 30 & 75mm), Security TRX-Star* Bits; T20H, T25H, T30H, T40H, T45H, T50H, T55H, T60H (1 each 30 & 75mm), Hex Bits; 4, 5, 6, 7, 8, 10, 12mm (1 each 30 & 75mm), Ribe Bits; M5, M6, M7, M8, M9, M10, M12, M14 (1 each 30 & 75mm), Spline Bits; M5, M6, M8, M10, M12 (1 each 30 & 75mm), Drive Adaptors; 3/8"Sq x 10mm Hex, Model No. 1/2"Sq x 10mm Hex. SEA AK21974

8pc Impact Socket Adaptor Set

Model No. SEA AK5900

500mm Magnetic Tool Holder

• • • •

Model No. SEA AK5612

Tidy storage for loose sockets.

Carry rail to the job or mount onto wall or toolbox.

Handle marked with drive size.

Supplied with 14 socket clips.

Model No. SEA AK1214

60pc Screwdriver Bit Set

Model No. SEA AK211

• Selection of popular sized screwdrivers, bits and 1/4’’Sq drive sockets.

• Chrome Vanadium steel with satin finish shafts.

• Shot blasted and magnetized tips.

• Contoured handles with soft grip for added control.

• Spinner top enables fingertip control of 50mm drivers.

• Contents: Standard Screwdrivers; Slotted - 6 x 38, 3 x 75, 5 x 75, 6 x 100, 8 x 150mm, Phillips - #2 x 38, #0 x 75, #1 x 75, #2 x 100mm, Precision Screwdrivers; Slotted - 2 x 50, 2.5 x 50, 3 x 50mm, Phillips - #000 x 50, #00 x 50, #0 x 50mm, TRX-Star* - T8 x 50mm, T10 x 50mm, Bits; Slotted - 3 (x2), 4 (x2), 5 (x2), 6mm (x2), Phillips - #0 (x2), #1 (x2), #2 (x2), #3 (x2), Pozi - #0 (x2), #1 (x2), #2 (x2), #3 (x2), TRX-Star* - T8, T10, T15, T20 (x2), T25, T30, T40, 1/4’’Sq Drive 6pt Socket Set - 5, 6, 7, 8, 9, 10, 11, 12 ,13mm, 1/4" Socket Adaptor, Bit Driver.

44pc Screwdriver, Hex Key & Bit Set • Chrome Vanadium satin finish shafts with shot blasted and magnetized tips.

• Contents: Screwdrivers; Slotted - 3 x 75, 4 x 100, 5 x 100, 6 x 125, 8 x 150mm, Phillips - #0 x 75, #1 x 75, #2 x 100, #3 x 150mm, Pozi #0 x 75, #1 x 75, #2 x 100, #3 x 150mm, TRX-Star** T25 x 100, T27 x 100, T30 x 125, T40 x 125mm, Bit Driver, 1/4" Hex Bits; TRX-Star** - T7, T8, T9, T10, T15, T20, Hex - 3, 4, 5, 6mm, Hex Keys; Metric - 1.5, 2, 2.5, 3, 4, 5, 5.5, 6mm, Imperial - 1/16", 5/64", 3/32", 1/8", 5/32", 3/16", 7/32", 1/4".

• Comprehensive set of TRX-Star*, Hex and Spline bits in Chrome Molybdenum steel, including a 1/2"Sq Drive bit holder with 2mm grub screw.

• Phosphate finish for corrosion resistance.

• Contents: Bits; TRX-Star* - T30, T40, T45, T47, T50, T55, T60, T70, Hex - 6, 7, 8, 10, 12, 14, 17, 19mm, Spline - M6, M8, M9, M10, M12, M14, M16, M18, 1/2"Sq Drive Bit Holder.

1/2"Sq Drive Socket Retaining Rail with 14 Clips

• Manufactured from drop-forged Chrome Vanadium steel with phosphate finish for added corrosion resistance.

• Sizes: 1/4"(F) x 3/8"(M), 3/8"(F) x 1/4"(M), 3/8"(F) x 1/2"(M), 1/2"(F) x 3/8"(M), 1/2"(F) x 3/4"(M), 3/4"(F) x 1/2"(M), 3/4"(F) x 1"(M), 1"(F) x 3/4"(M).

• Wall or toolbox mounting magnetic rack.

• Size: 500 x 40mm.

• Suitable for retaining frequently used steel tools such as screwdrivers, spanners and pliers.

• Supplied with fixing screws.

25pc 1/2"Sq Drive Impact TRX-Star*/ Hex/Spline Bit Set

Model No. SEA S01110

44pc Hammer-Thru Screwdriver, Hex Key & Bit Set

Model No. Model No. S01090

Model No. S01106

SEA S01090 SEA S01106

Hammer-Thru ✘ ✔

27

7pc Screwdriver Set VDE Approved

10pc Pipe Flaring & Cutting Kit

• Tubing kit suitable for cutting and flaring copper, brass or thin walled aluminium pipe.

• Includes screw-type tube cutter with die-cast frame and integral de-burring tool.

• Dies: 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 5/8".

• Fully insulated to VDE and EN 60900 standards to protect from electric shocks up to 1000V. • Contents: Slotted; 3 x 75, 4 x 100, 5.5 x 125mm, 6.5 x 150mm, Phillips; #0 x 75, #1 x 80, #3 x 100mm.

Model No. SEA AK6125

3pc Locking Pliers Set

• • • •

Premier quality set with deep-cut jaws.

Coated in black anti-rust finish.

Sizes: 125, 175, 250mm.

Maximum Jaw Capacities: 30, 40, 45mm.

Model No. SEA AK506

4pc Circlip Pliers Set

• Spring loaded jaw sets manufactured from hardened and tempered steel.

• Internal and external, in both straight and bent configuration.

• Pliers are fully polished and fitted with non-slip polyfoam grips.

Model No. • Min./Max. Circlip Capacity: SEA AK8440 19-60mm.

Model No. SEA AK668

750mm 1/2"Sq Drive Breaker Bar

1/2"Sq Drive Knuckle for AK730 & AK7302

• Hardened and tempered Chrome Vanadium steel bar with high chrome finish.

• Long, slim style handle and spring loaded socket retention.

• Fully replaceable knuckle joint*. *Note: Knuckle joints are not covered by the lifetime guarantee and are treated as consumable items.

• Knuckle joint for Model No’s AK730 & AK7302 1/2"Sq Drive Breaker Bar.

Model No. SEA AK7302

100W Soldering Iron

Model No. SEA AK730/RK

8pc Soldering Gun/Iron Kit

• Comprehensive kit comprising 100W soldering gun, 30W soldering iron, iron holder, excess solder extractor, scraper, spare tips, solder wire and universal workpiece clamps.

• Fitted with 3-pin plugs.

• Class 1 electrically insulated soldering iron with cool grip handle which stays comfortable during prolonged use.

• Fitted with replaceable soldering tip.

• Includes 1.5m cable with 3-pin plug.

• Complies with Low Voltage Directive and Model No. Electromagnetic Compatibility Directives.

SEA SD100

28

36mm Bi-Hex 1/2"Sq Drive Deep Impact Socket

Model No. SEA SD300K

• Forged and heat treated Chrome Vanadium steel impact grade bi-hex deep socket, chemically blackened for corrosion resistance.

• Malleable steel material makes the socket suitable for use with either hand ratchet wrenches or air impact wrenches.

Model No. SEA SX006

Ø60mm Flexible Shaft Inspection Mirror

• Rubber grip and strong, spring steel flexible shaft.

• Ø60mm Mirror.

• Suitable for use in confined areas.

• Length: 485mm.

Model No. SEA AK6503

Locking Pocket Knife with Quick Change Blade

• Spring loaded multi-switch releases blade holder from handle when folded and operates quick change mechanism for easy blade removal/fitting - no tools required.

• Closed/Open Length: 110/175mm.

• Supplied with six reversible high carbon steel blades.

2pc 15 Function Multi-Tool & Twin Blade Knife Set

• Multi-tool functions include combination pliers, long nose pliers, wire cutter, fine edge blade, bottle opener, can opener, slotted screwdrivers, Phillips screwdriver, fish scaler, file, hook remover, ruler, wood saw and single/double file.

• Multi-Tool Lengths (Open/Closed): 160/105mm.

• Twin Blade Knife Lengths (Open/Closed): 180/110mm.

Model No. SEA PK27

Model No. SEA PK23

Rivet & Threaded Nut Rivet Kit

6pc Hook-and-Loop Sanding Block Kit

• Comprehensive kit of resilient rectangle style concave and convex sanding blocks with hook-and-loop surfaces and a flexible tear drop sanding block.

• Sizes: Sanding Blocks; RE4015 - Concave 85 x 155mm, RE4016 - Convex 80 x 155mm, RE4017 - Convex 85 x 160mm, RE4019 - Flexible Tear Drop 90 x 135mm, Model No. RE4020 - Concave 90 x 155mm & SEA RE40KIT RE4022 - Convex Hook-and-Loop 90 x 150mm.

Plastic Riveting Kit • Drop-forged frame with patented folding mechanism for compact storage.

• Comfortable cushion grips.

• Heavy-duty head suitable for fixing blind rivets and threaded nut rivets to thin sheet material.

• Suitable for aluminium, steel and stainless steel.

Model No. SEA AK39602

10tonne Straightener Kit with Variable Tilt • Suitable for applying plastic rivets found in automotive applications.

• Designed for one-handed operation and one-stroke setting.

• Allows access in hard-to-reach areas not accessible by conventional lever type tools.

• Universal nose piece suitable for all sizes of plastic rivets.

• Rivets: 10pc x Ø6.6 x 17.2mm, 10pc x Ø6.3 x 25.2mm, Model No. 10pc x Ø5 x 15.8mm, 10pc x Ø5 x 17.2mm.

SEA RT001

Hook-and-Loop Sanding Blocks 002

. RE4 el No

Mod

001

. RE4 el No

• • • •

Fully interchangeable parts and hydraulics.

Variable position upright allows six preset angles of pull plus a seventh upright position.

Supplied as standard with SuperSnap® manual hydraulic pump and ram.

Supplied with Pull Clamp (x2), Sill Clamp (x2), Chain (x2), Chain Hook (x2), Carriage Anchorage Tube, Tube Stand (x2).

Model No. SEA DZRE92/C

Mod

Model No.

Size

SEA RE4001

Ø150mm

SEA RE4002

Ø150mm

29

20tonne Snap Body Repair Kit

• Heavy gauge snap-together pipe-work and snap-together attachments.

• Compatible with most other leading makes of snap-together equipment.

• Supplied with 20tonne hand operated pump, hose, hydraulic ram and metal storage case.

Professional Car Parts Trolley

• Heavy-duty parts trolley for organized storage of car parts.

• Equipped with hanging rack for bumpers and exhaust pipes.

• Also includes a parts shelf, writing board, small parts basket and elastic straps.

• Fully moveable on four castor wheels.

• Maximum Capacity: 90kg.

• Size (H x W x D): 1700 x 890 x 590mm.

• Model No. MK70 • List Price £349.95

Model No. SEA RE9720

Model No. SEA MK70

22pc Spray Gun Cleaning Set

• Comprehensive cleaning set with a range of soft, medium, hard and brass bristle brushes.

• Includes precision brush/probe sets and empty bottle for lubricant.

• Suitable for various applications.

• Contents: 95mm Mini Brushes (x6), Soft/Medium Brushes; 155, 210, 310mm (Angled), 155mm Brass Brush, 170mm Brush with 35mm Hard Bristles, Precision Brushes (x3) & Holder, Precision Probes (x6) & Holder, Lubricant.

Model No.

SEA BSGC5

Reciprocating Air Saw

Air Operated Wax Injector Kit

• Designed for the application of wax rust inhibitor.

• Supplied with a selection of lances to enable wax to be sprayed into body cavities through a small hole.

• Suitable for a variety of bodyshop applications such as cutting through panels, sills and chassis members.

• Excellent for initial crash-repair preparation when quick removal of damaged panels is required.

• Fitted with safety trigger device.

• Supplied with a starter pack of blades.

Model No. • Air Supply: 90psi - 6cfm.

42pc Air Angle Die Grinding/ Sanding Kit

SEA SA34

20m Retractable Air Hose Reel Ø10mm ID

15m Retractable Air Hose Reel Ø12.5mm ID

• Solid brass internal spindle for added strength and durability.

• Self layering system provides tangle free operation.

• Auto rewind mechanism.

• Reinforced braided PVC hose.

• Suitable for the professional workshop.

• Supplied with heavy-duty swivel mounted wall bracket and 2m inlet hose.

Model No. • Inlet-Outlet: 3/8"BSPT. SEA SA93

• Solid brass internal spindle for added strength and durability.

• Self layering system provides tangle free operation.

• Auto rewind mechanism.

• Reinforced PVC braided hose.

• Suitable for professional workshop.

• Supplied with heavy-duty swivel mounted wall bracket and 2m inlet hose.

Model No. • Inlet-Outlet: 1/2"BSPT. SEA SA94

30

Model No. SEA SG18

• Suitable for die grinding, sanding or panel preparation.

• Generation Series 90° Air Angle Die Grinder (Model No. GSA674).

• Safety trigger prevents inadvertent operation.

• Contoured rubber handle for reducing vibration and added comfort.

• 360° Rotating exhaust.

• Includes a range of die grinding points, sanding rolls and Ø50/75mm preparation pads.

• Replacement components Model No. readily available.

SEA GSA674K

1/4" & 1/2"Sq Drive 2-in-1 Mini Air Ratchet Wrench

• Textured finish to ensure a good grip.

• Mini design for working in confined areas, ideal for working around engines where space is limited.

• 2-in-1 Air ratchet 1/4"Sq Drive head with 1/2"Sq Drive adaptor easily fitted on to ball with hex grub screw, hex key supplied.

• Fitted with a twist reverse action and trigger operated power control.

• Features rear exhaust with baffle for reduced noise level and safety throttle lever to stop accidental operation.

• Suitable for professional workshop use.

Model No. SEA SA1001

3/8"Sq Drive Mini Air Ratchet Wrench

• Textured finish to ensure a good grip.

• Mini design for working in confined areas, ideal for working around engines where space is limited.

• Fitted with a twist reverse action and trigger operated power control.

• Features rear exhaust with baffle for reduced noise level.

• Suitable for professional workshop use.

Model No. SEA SA1002

Ø50mm Mini Air Sander

• Textured finish to ensure a good grip.

• Mini design for working in confined areas, ideal for working around engines where space is limited.

• Lightweight and versatile sanding tool suitable for use with discs and pads with industry standard fitting.

• Fitted with safety release trigger control and variable speed adjustment.

• Features rear exhaust with baffle for reduced noise level and safety throttle lever to stop accidental operation.

• Suitable for professional workshop use.

• Includes backing pad and wrenches.

• Replacement backing pad Model No. PTC50VAM6.

• Replacement Sanding Discs: 10pcs (each); Model No’s SA701D60G (60 grit), SA701D80G (80 grit) & Model No. SA701D120G (120 grit).

SEA SA1003

Ø6mm Mini Air Die Grinder

90° Ø6mm Mini Air Die Grinder

Mini Reciprocating Air Saw

• Textured finish to ensure a good grip.

• Mini design for working in confined areas, ideal for working around engines where space is limited.

• Safety trigger prevents inadvertent operation.

• Ideal for re-shaping, deburring and smoothing off rough edges on castings.

• Suitable for the professional workshop.

• Supplied with fitting spanner.

• Textured finish to ensure a good grip.

• Mini design for working in confined areas, ideal for working around engines where space is limited.

• Safety trigger prevents inadvertent operation.

• Ideal for re-shaping, deburring and smoothing off rough edges on castings.

• Suitable for the professional workshop.

• Supplied with fitting spanner.

• Textured finish to ensure a good grip.

• Suitable for a variety of bodyshop applications such as cutting through panels, sills, chassis members etc.

• Excellent for initial crash-repair preparation when quick removal of damaged panels is required.

• Fitted with safety trigger device.

• Suitable for the professional workshop.

• Supplied with starter pack of blades.

• Replacement Blades; SA34/B14, SA34/B24 & SA34/B32 (packs of 5).

Model No. SEA SA1004

Ø6mm Mini Air Drill

Model No. SEA SA1005

Ø6mm Mini Air Angle Drill

• Textured finish to ensure a good grip.

• Mini design for working in confined areas, ideal for working around engines where space is limited.

• Powerful mini drill 6000rpm, Ø6mm key chuck 1-6mm drill bits.

• Safety trigger prevents inadvertent operation.

• Suitable for professional workshop use.

• Supplied with chuck key.

Model No. SEA SA1007

• Textured finish to ensure a good grip.

• Mini design for working in confined areas, ideal for working around engines where space is limited.

• Powerful mini drill 4500rpm, Ø6mm key chuck 1-6mm drill bits.

• Safety trigger prevents inadvertent operation.

• Suitable for professional workshop use.

• Supplied with chuck key.

Model No. SEA SA1008

Model No. SEA SA1006

1/4"Sq Drive Air Impact Wrench Diesel Glow Plug Kit

• Reduced torque impact wrench suitable for the removal of seized glow plugs.

• Four-position air regulator - 10, 20, 30, 40Nm. • One-hand operation for trigger and forward/reverse control.

• Includes 8, 9, 10, 11, 12mm deep impact sockets, Model No. 50mm extension bar and universal joint.

SEA SA141

31

10 x 330mm Air Belt Sander

1/2"Sq Drive Composite Air Impact Wrench Twin Hammer

• Aluminium housing with articulated sanding arm.

• Features belt tracking control, heavy-duty nose roller and one-handed trigger operation.

• Suitable for sanding otherwise inaccessible areas such as around door-shuts.

• Supplied with three belts.

Model No. • Replacement belts readily available.

SEA SA35

• Maximum Torque: 950lb.ft(1288Nm).

• Breakaway Torque: 1050lb.ft(1428Nm).

• Twin hammer design gives the wrench a high torque output making it suitable for jobs that would normally require a 3/4" impact wrench.

• Two stage trigger design offers increased control with feather touch trigger for running up to 272Nm and fully depressed for full torque.

• Features hammer cage support mechanism to reduce tool vibration while in operation.

1/2"Sq Drive Air Impact Wrench Twin Hammer

• Breakaway Torque: 500lb.ft(680Nm).

• Maximum Torque: 480lb.ft(653Nm).

• Powerful impact wrench with twin hammer mechanism for increased torque.

• Air motor features quality bearings, ductile steel end plates and carefully finished components to ensure smooth running and maximum power.

• Combination forward/reverse and speed selector.

• 2-Year Guarantee.

Model No. SEA SA6006

Composite Mini Air Screwdriver

Model No. SEA SA602

• Compact design is ideal for accessing work areas where space is limited.

• Composite lightweight housing reduces effects of chill on operator’s hands.

• Fully reversible with thumb control on side of motor housing.

• Air motor with quality bearings for smooth and powerful operation.

• Features 1/4"Hex quick release chuck for fast bit changes.

• Suitable for the professional workshop.

Model No. SEA SA623

180mm Palm Type Air Blow Gun

290mm Palm Type Air Blow Gun

Palm Type Air Blow Gun with Safety Nozzle

• Die-cast metal body with moulded handle and hanging point.

• Palm type gun with thumb trigger control.

• Length of Lance: 180mm.

• Air Inlet Size: 1/4"BSP. Model No. • Maximum Operating Pressure: 110psi.

SEA SA913M

• Die-cast metal body with moulded handle and hanging point.

• Palm type gun with thumb trigger control.

• Length of Lance: 290mm.

• Air Inlet Size: 1/4"BSP. Model No. • Maximum Operating Pressure: 110psi.

SEA SA913L

• Die-cast metal body with moulded handle and hanging point.

• Palm type gun with thumb trigger control.

• Supplied with jet and safety nozzle.

Model No. • Maximum Operating Pressure: 110psi.

SEA SA913

32

53pc 3.6V Cordless Screwdriver Set

1600W Hot Air Gun 375°C/500°C • 2-Step switch for temperature and airflow control.

• Gun can also stand vertically.

• Suitable for paint stripping, soft soldering, removing sticky labels and defrosting frozen pipes.

• Fitted with 3-pin plug.

• Nozzles available separately.

• Temperature Range: 375°C/500°C.

• Powerful, lightweight screwdriver featuring locking swivel adjustment from pistol to straight type.

• Forward, reverse and trigger-lock control.

• Eight adjustable torque settings.

• Quick release 6mm bit holder.

• Integral LED light to illuminate working area.

• LED Torch in base of handle.

• Three LEDs indicate battery life.

• Soft grip handle for comfort and control.

• Powered by a Lithium-ion battery which has no memory effect, longer lasting than Ni-Cd cells and recovers from a deep discharge state without affecting overall capacity.

• Contents: Screwdriver Bits; Slotted - 3 (x2), 4 (x2), 5 (x2), 6mm (x2), Phillips - #1 (x5), #2 (x5), #3 (x4), Pozi - #1 (x4), #2 (x4), #3 (x4), TRX-Star* - T8 (x2), T10 (x2), T15 (x2), T20, T25, T27, T30, T40, T45, Hex - 3 (x2), 4 (x2), 5mm (x2), Magnetic Bit Holder.

450W Glue Gun - 230V

Model No. SEA CP36S

Magnetic Glove Dispenser

• Ready to use in less than five minutes.

• Unplug for cordless use once fully heated.

• On/off switch and trigger feed control.

• Composite housing with soft grip for added comfort.

• Suitable for Ø11 x 100mm glue sticks.

• Two glue sticks can be loaded at once.

• 25pc Glue stick packs available separately Model No. AK292/2.

• Features magnets in handle base for adhering to metal stand when not in use.

Model No. SEA AK2921

24 Bin & Panel Combination

• Dispenser attaches to any ferrous surface and can also be wall mounted.

• Four small magnets hold the dispenser in place.

• Suitable for packs of 50/100 disposable gloves.

• Self-adjusting springs to hold different box sizes.

• Size (W x D x H): 146 x 95 x 254mm.

Model No. SEA HS105

Welding Bottle Trolley 1 Bottle

Model No. SEA APGD

24 Bin & Panel Combination

• Lightweight tubular steel frame with large diameter wheels for easy transportation of heavy cylinders.

• Accepts cylinders of up to Ø250mm.

Model No. SEA ST28S

• Bins manufactured from shockproof polymer which is resistant to mild acids, solvents and oils.

• Bins have a high thermal stability and resist damage from extremes of temperature.

• Bin Dimensions (W x D x H): 100 x 110 x 75mm.

• Steel Panel Dimensions (W x D x H): 630 x 10 x 380mm.

• Supplied with heavy-duty steel back panel.

Model No.

SEA TPS130

Adjustable Arm Safety Spectacles

• BS EN 166/F - Wraparound, clear, anti-scratch, polycarbonate lens.

• Adjustable length nylon arms for a snug fit.

Model No. SEA SSP44

• Bins manufactured from shockproof polymer which is resistant to mild acids, solvents and oils.

• Bins have a high thermal stability and resist damage from extremes of temperature.

• Bin Dimensions (W x D x H): Medium; 100 x 160 x 75mm, Large; 100 x 210 x 75mm.

• Steel Panel Dimensions (W x D x H): 630 x 10 x 380mm.

• Supplied with heavy-duty steel back panel.

Model No.

Safety Goggles with Detachable Face Shield

SEA TPS131

Premium Powder-Free Disposable Nitrile Gloves Extra-Large Pack of 100

• More durable than standard latex gloves.

• Provides excellent protection whilst being light and flexible.

• Nitrile material, ideal for people with latex protein allergies.

• Manufactured to EN455 Parts 1, 2 & 3.

Model No. SEA SSP55XL

• BS EN 166 BT 3 - Manufactured from polycarbonate for superior durability and resistance.

• Offers full face protection with an increased range of mobility compared to a standard face protector.

• Curved face shield conforms to the shape of the face offering improved protection.

• Detachable indirect vented goggles to allow for extra versatility.

• Features a wide angle curved lens for enhanced visibility.

• Adjustable headband with soft Model No. PVC frame provides added comfort.

SEA SSP76

33

Mobile Engine Repair Workbench

• Sturdy steel construction with powder coated finish to prevent corrosion.

• Angled worktop to one drain point makes this ideal for working on engines, transmissions, gearboxes or hydraulic systems.

• All fluids drain into a removable polyethylene container.

• Features a lockable drawer, a bottom shelf ideal for parts and tool storage and four swivel castors, two of which are locking.

Model No. • Size (W x D x H): 1205 x 640 x 880mm.

SEA AP1200MW • Capacity: 250kg.

Adjustable Height Mobile Workstation

• Table is fully adjustable in height.

• Features 4-section table, one large for main workpiece and three equal sized smaller sections for accessories.

• Rubber lining on the table helps prevent damage to the unit and workpiece.

• Suitable for use in workshops and warehouses.

• Supplied with four castor wheels.

• Table Size (W x D): 730 x 505mm.

• Min./Max. Height: 890/1190mm.

• Model No. AP200 • List Price £117.95

3-Level Composite Workshop Trolley

• Composite garage workshop trolley with a 30kg capacity per shelf.

• Walls on only three sides of shelf allow easy access when adding or removing items to and from trolley.

• Four large castors, two locking.

Model No. • Can also be used as a janitorial trolley.

SEA CX308 • Overall Size (W x D x H): 800 x 410 x 930mm.

18 Drawer Cabinet Box

• Tough and durable housing, contains 18 impact resistant composite drawers.

• Fitted with four fixing points for wall mounting or can be bench mounted (freestanding).

• Overall Size (W x D x H): Model No. 380 x 160 x 475mm.

SEA APDC18R

39 Drawer Cabinet Box

60 Drawer Cabinet Box

• Tough and durable housing, contains 39 impact resistant composite drawers.

• Fitted with fixing points for wall mounting or can be bench mounted (freestanding).

• Overall Size (W x D x H): Model No. 380 x 160 x 475mm.

SEA APDC39R

• Tough and durable housing, contains 60 impact resistant composite drawers.

• Fitted with fixing points for wall mounting or can be bench mounted (freestanding).

• Overall Size (W x D x H): Model No. 380 x 160 x 475mm.

SEA APDC60R

34

32pc Tap & Die Set Split Dies - Metric

150mm Heavy-Duty Professional Cast Iron Fixed Base Vice

• • • • •

Super quality cast iron construction.

Replaceable steel jaws.

Features an anvil.

2 Year guarantee against breakage.

Jaw Opening: 150mm.

Model No. SEA CV150XT

200mm Heavy-Duty Professional Cast Iron Fixed Base Vice

• • • • •

Super quality cast iron construction.

Replaceable steel jaws.

Features an anvil.

2 Year guarantee against breakage.

Jaw Opening: 200mm.

Model No. SEA CV200XT

• M3 to M12 alloy steel tap and die set.

• Taps supplied in three types for each size, taper (starting), second tap (intermediate) and plug (bottoming).

• Matched by equivalent sized dies.

• Provides all functions required for a professional engineer.

Model No. • Set includes tap wrench, steel die handle, SEA AK3015 screw pitch gauge and screwdriver.

40pc Tap & Die Set - Split Dies

45pc Tap & Die Set - Split Dies

• High carbon steel taps and dies.

• Dies with machined lead-ins for ease of use.

• Set includes one long handled adjustable tap wrench with professional type sliding jaw.

• Steel die-holder with retention screw, suitable for dies from M3 up to M12.

• Also includes T-Bar type tap wrench, screwdriver and thread gauge.

• Ideal for the engineer and farmer.

• Complete range of metric Tungsten taps and dies, 6mm up to 24mm.

• Includes Tap Wrench, T-Bar Tap Wrench and Steel Die Wrench.

Model No. SEA AK301

40pc Tap & Die Set Split Dies

Model No. SEA AK303

3pc Micrometer Set - Metric

• Set includes three external micrometers ranging from 0-75mm.

• Supplied with extension sets and adjusting wrench.

Model No. SEA AK9651M

11kg Anvil • Bench mounting cast iron anvil, featuring single bick and rectangular working surface.

• Rectangular Working Surface (W x D): 170 x 90mm.

• Overall Size (W x D x H): 285 x 120 x 136mm.

• Die holder features self-centring mechanism for straight and accurate thread cutting.

• Includes T-handled tap wrench and Metric screw pitch gauge.

• Sizes: 3-12mm.

Model No. SEA AK3040

Model No. SEA ANV11

35

0-150mm(0-6") Digital Vernier Caliper

• 11mm LCD display.

• Hardened and tempered stainless steel with satin finish.

• Metric and Imperial readings with conversion between the two.

• Zero setting control for comparative measurement.

Dial Gauge Indicator 10mm Travel

• Precision ground base with rotary magnetic control.

• Articulated arm with rotary lock.

• Combination dial and scribing clamp with fine adjustment control.

• Precision mechanism with Ø55mm dial and locking, rotating bezel.

• Interchangeable foot.

Model No. SEA AK962EV

20pc Screw Pitch Gauge Set

Heavy-Duty Magnetic Stand without Indicator

Model No. SEA AK961M

Model No. SEA AK960

3pc T-Handle Tap Wrench Set

• General purpose tap wrenches for tapping and reaming.

• Solid jaw design and heavy knurled cap.

• Maximum Square Size; Small Wrench – 3.9mm, Medium Wrench – 5mm, Large Wrench – 7mm.

• Supplied in pouch.

Model No.

• Folding 20 blade set, individually stamped with accurate thread profiles.

• Range: 0.4-6mm.

Model No. SEA AK71SPG

SEA AK9799

200mm Double End Engineer’s Scriber

150mm Carbide Tipped Scriber

• Precision manufactured tool with hardened steel tips.

• Features straight and 90° tips with knurled body.

Model No. SEA AK9751

36pc 8mm Letter & Number Punch Set

• 66mm Long, high carbon steel punches.

• Hardened, tempered and chemically blackened.

• Full set of alpha-numeric characters including the ampersand symbol (number 6 doubles as number 9).

• 8mm Character height.

Model No. SEA AK8297

5pc Engineer’s File Set

• Fitted with pocket clip.

• Suitable for use on glass, metals and ceramics.

• Ideal for machinists, welders, tinsmiths and hobbyists.

Model No. SEA AK9752

• Popular set of assorted files with comfort grip handles.

• Each file is double cut for faster removal of material from workpiece.

• Contents: Half-Round, Round, Square, Three-Square, Flat.

Model No. SEA AK573

10mm Cylindrical Front End Cut Tungsten Carbide Rotary Burr

10mm Cylindrical Ball Nose Tungsten Carbide Rotary Burr

Ø10mm Arc Round Nose Tungsten Carbide Rotary Burr

10mm Conical Ball Nose Tungsten Carbide Rotary Burr

• 10mm Burr made from Tungsten Carbide.

• Cylindrical front end No. 6 cut (universal).

• For use on soft and hard metals, including welded seams.

• Supplied in a plastic storage box.

• 10mm Burr made from Tungsten Carbide.

• Ball nose No. 6 cut (universal).

• For use on soft and hard metals, including welded seams.

• Supplied in a plastic storage box.

• Ø10mm Burr made from Tungsten Carbide.

• Arc round nose No. 6 cut (universal).

• For use on soft and hard metals, including welded seams.

• Supplied in a plastic storage box.

• 10mm Burr made from Tungsten Carbide.

• Conical ball nose No. 6 cut (universal).

• For use on soft and hard metals, including welded seams.

• Supplied in a plastic storage box.

Model No. SEA SDB01

36

Model No. SEA SDB02

Model No. SEA SDB05

Model No. SEA SDB06

Lead-Free Soldering Wire Dispenser Tube

• Tube of flux cored lead-free wire for general purpose soldering.

Model No. SEA SW20

80W Bench Mounting Drill Bit Sharpener

Tow Pole with Shock Spring 2000kg Rolling Load Capacity

• Free Speed: 4200rpm.

• Fast, simple and effective way to sharpen your drill bits.

• Gives a perfect angle/sharpened head to make drilling with your bit easier.

• Suitable for up to 118° HSS Titanium, Model No. Cobalt, Carbon Steel and Split Point SEA SMS2008 bits in range Ø3-13mm.

• • • •

Ø65mm Twist Knot Wire Cup Brush M14 x 2mm

• Suitable for use with power tools up to the maximum rated rpm.

• Twisted steel filaments give more aggressive cleaning action - ideal for heavy rust removal.

Model No. SEA TKCB651

Ø75mm Wire Cup Brush with 6mm Shaft

3pc Miniature Brush Set

• Composite stocked brush set with hanging holes.

• Steel, nylon and brass filled heads.

• Suitable for cleaning spark plugs and smaller engineering components.

3pc Miniature Wire Brush Set • Composite stocked brush set with contoured soft grip handles.

• Stainless steel, nylon and brass filled heads suitable for cleaning spark plugs and smaller engineering components.

• Includes hanging hole.

Model No. SEA AK9791

Brassed Steel Wire Brush

Model No. SEA WB05/R

2-Tread Trade Aluminium Folding Platform EN 14183

200mm Tap Wrench

• Professional style steel tap wrench with sliding jaws.

• Suitable for tap sizes between M3 and M12.

Model No. SEA AK727

30L Wet & Dry Vacuum Cleaner 1100W • High powered, lightweight unit with blower facility.

• Constructed from high impact plastic, the drum unit is mounted on four castor wheels.

• Tool storage points on the base.

• Supplied with 4m cable with 3-pin plug, tool kit, wet and dry cartridge filter.

• Heavy-duty 1220mm aluminium handle and galvanized steel frame with 24"(600mm) rubber blade.

• Suitable for oil, water and other liquid spills.

Can be used inside or outside.

Model No. SEA BM24RSM

Model No. SEA WB100

• Brassed steel filaments.

• Curved, folded, alloy stock with composite handle.

• Suitable for use with power drills.

• Crimped brassed steel filaments add extra rigidity Model No. and cleaning power.

SEA SCB75

24"(600mm) Rubber Floor Squeegee with Aluminium Handle

2000Kg rolling capacity tow bar ideal for the safe secure towing of motor vehicles.

Connects to car towing eyes with secure attachment hooks.

Tow pole has a damping spring to mitigate shock from acceleration or braking.

Pole easily adjusted to match the towing eye orientation of both towed and towing vehicle.

Model No. • Breaks down for easy storage and is supplied with SEA TPK2522 storage bag.

• • • • • • •

Platform Height: 500mm.

Platform Size: 300 x 950mm.

EN 14183 Approved folding and portable 2-tread aluminium platform with 150kg capacity.

Large, ribbed non-slip platform and treads for safe and easy manoeuvrability.

Durable aluminium alloy frame with ribbed feet for extra stability.

Safety locking catches on legs.

Model No. Folds flat for easy storage and transportation.

SEA APS2

Model No. SEA PC300

37

Platform Truck 150kg Capacity

Platform Truck 300kg Capacity

• Rigid platform truck features rubberised deck and bumper strip.

• Platform Size: 725 x 465mm.

• Handles fold flat for ease Model No. of storage.

SEA CST991

• Rigid platform truck features rubberised deck and bumper strip.

• Platform Size: 910 x 605mm.

• Handles fold flat for ease Model No. of storage.

SEA CST992

19mm x 20m PVC Insulating Tape Mixed Colours - Pack of 10

19mm x 20m Black PVC Insulating Tape - Pack of 10

RoHS Compliant insulating tape.

Thickness: 0.15mm.

Elongation: 125%.

Tensile Strength: 22N/100mm.

Temperature Rating: -18°C to 150°C. • Self extinguishing.

• • • • •

• • • • •

Model No. SEA ITMIX10

4-30mm Double Flute HSS M2 Step Drill Bit

RoHS Compliant insulating tape.

Thickness: 0.15mm.

Elongation: 125%.

Tensile Strength: 22N/100mm.

Temperature Rating: -18°C to 150°C. • Self extinguishing.

100L Refuse/Wheelie Bin - Red

• Durable refuse/wheelie bins made from polypropylene.

• Red recommend for plastics but can be used as desired.

• Solid rear axle with two Ø200mm wheels and three robust handles allow the bins to be moved easily even when full.

Model No.

SEA BM100R

300 x 4.8mm White Cable Tie Pack of 100

• Ties manufactured from nylon 66 making them heat resistant over the temperature range -40°C to +85°C. • Supplied in handy sized packs.

• Suitable for workshop, garden and home applications.

Model No. SEA ITBLK10

Model No. SEA CT30048P100W

Splashproof Standard Blade Fuse Holders - Packs of 10

Model No. FHSP30 Model No. FHSP20 High-speed HSS M2 double flute step drill.

Double straight flutes for efficient swarf clearance.

Allows clog-free precision drilling.

Hole Sizes: 4-30mm in 2mm increments.

Model No. • Supplied in plastic SEA AK4732 storage case.

• • • •

555pc Imperial & Metric Split Pin Assortment - Small Sizes

• Contents (Approx. Quantity): 1/16" x 1" (1.6 x 25.4mm) (x150), 3/32" x 1" (2.4 x 25.4mm) (x150), 3/32" x 1-1/2" (2.4 x 38mm) (x100), 1/8" x 1-1/4" (3.2 x 32mm) (x75), 1/8" x 2" (3.2 x 51mm) (x50), 5/32" x 2-1/2" (4 x 63mm) (x30).

• Splashproof fuse holders.

• Packs of 10.

88pc Bonded Seals Assortment

• Contents (Approximate Quantity): M18 (x8), M20 (x5), M22 (x5), M24 (x5), M10 (x20), M12 (x15), M14 (x15), M16 (x15).

Model No. SEA AB001SP

38

Model No.

Model No. SEA AB010DS

Rating

SEA FHSP20

20A

SEA FHSP30

30A

60pc Crocodile Clip Assortment Red & Black

• Contents (Approximate Quantity): Non-Insulated; 55 (x20), 70 (x2), 75mm (x2), Insulated; 45 (x16), 55 (x12), 60mm (x8).

Model No. SEA AB023CA

200pc Blue, Red & Yellow Crimp Terminal Assortment

• Contents (Approximate Quantity): Blue; Bullet; Ø5mm (x10), Butt Connector; Ø4.5mm (x30), Easy-Entry Ring; Ø8.4mm(5/16”) (x10), Female Socket; Ø5mm (x10), Fully Insulated Female; 6.3mm (x10), Push-On Female; 6.3mm (x10), Push-On Male; 6.3mm (x10), Red; Bullet; Ø4mm (x10), Butt Connector; Ø3.3mm (x20), Female Socket; Ø4mm (x10), Fully Insulated Female; 6.3mm (x10), Push-On Female; 2.8mm (x10), Push-On Male; 6.3mm (x10), Yellow; Butt Connector; Ø5.5mm (x20), Model No. Easy-Entry Ring; Ø6.4mm(1/4”) (x10), Ø8.4mm(5/16”) (x10).

SEA AB038MT

225pc Air Conditioning Rubber O-Ring Assortment

• Made from HNBR. • Designed for use with Freon R134a making them suitable for automotive air conditioning units and many other applications.

Model No. SEA ACOR225

36pc Automotive MAXI Blade Fuse Assortment

100pc Automotive MINI Blade Fuse Assortment

120pc Automotive Standard Blade Fuse Assortment

• Contents (Approximate Quantity): 2A, 3A, 4A, 5A, 7.5A, 10A, 15A, 20A, 25A, 30A (10 of each).

• Contents (Approximate Quantity): 3A, 5A, 7.5A, 15A, 20A, 30A (15 of each), 10A (x30).

Model No. SEA BCF100

Model No. SEA BCF120

250pc Diesel Injector Copper Washer Assortment - Metric

Parts Cleaning Brush with Hose

• Contents (Approximate Quantity): ID x OD x Thickness; Ø6 x Ø10 x 1 (x20), 10 x 13.5 x 1 (x20), 10 x 20 x 1 (x20), 12 x 16 x 1.5 (x20), 14 x 18 x 1.5 (x20), 16 x 20 x 1.5 (x15), 21 x 25 x 1 (x10), 8 x 11.5 x 1 (x20), 10 x 14 x 1 (x20), 10 x 20 x 2 (x20), 12 x 18 x 1.5 (x20), 14 x 20 x 1.5 (x20), 17 x 21 x 1.5 (x15), 22 x 27 x 1mm (x10).

• Fits onto the flexible spout of Sealey parts cleaning tanks (except SM21) and allows a stream of fluid to pass through the bristles for extra cleaning power.

• Supplied with hose, adaptor nipple and two hose clips.

Model No. SEA AB027CW

Model No. SEA SM201

419pc Rubber O-Ring Assortment

• Automotive MAXI blade type fuse assortment.

• Contents (Approximate Quantity): 20A, 30A, 40A, 50A (6 of each), 60A, 70A, 80A, 100A (3 of each).

Model No. SEA BCF36

Quick Release Positive-Negative Battery Clamps - Pair Copper-zinc plated steel & brass.

RoHS Compliant.

Cable Size: 25mm².

Post Size (Positive/Negative): Ø19mm/Ø17.5mm.

• Blue & red.

• Enables quick release.

• • • •

Model No. SEA BTQK12

• Manufactured from Buna-N. • Contents: (Approximate Quantity) ID x Thickness; Ø18 x 3.5, 20 x 3.5, 22 x 3.5, 23.5 x 3.5, 25 x 3.5, 26.5 x 3.5, 28 x 3.5, 30 x 3.5, 31 x 3.5, 33 x 3.5, 34.5 x 3.5, 36 x 3.5, 38 x 3.5, 41 x 3.5, 44 x 3.5, 47 x 3.5, 50 x 3.5mm (10 of each), 11 x 2.5, 14 x 2.5, 19 x 2.5, 22 x 2.5mm (13 of each), 10 x 2.5, 13 x 2.5, 16 x 2.5, 18 x 2.5, 21 x 2.5mm (14 of each), 5 x 2mm (x18), 3 x 1.5, 4.4 x 2mm (20 of each), 7 x 1.5, 10 x 1.5, 13 x 1.5 (23 of each).

Model No. SEA BOR419

39

12V Digital Heavy-Duty Tyre Inflator • Air Delivery: 50L/min.

• Will automatically inflate tyres to preset pressure without the need for fiddly gauges.

• Typical Inflation Time: 0-30psi in 104sec (175/70/R13).

• 4.5m Air hose with quick release coupling and 3m power cord with clamps for use on 12V battery.

• Suitable for inflating tyres on lawnmowers, motorcycles, cars and vans.

• Supplied in a storage bag with accessory kit including ball needle and adaptors for inflatables.

Model No. SEA MAC05D

Mo

del

del

Mo

N

o.

SE

A AM

C

05D

No.

SEA

MA

C04

D

12V Digital Tyre Inflator/Mini Air Compressor • Air Delivery: 25L/min.

• Typical Inflation Time: 0-30psi in 139sec (175/70/R13).

• Will automatically inflate tyres to preset pressure without the need for fiddly gauges.

• 2m Air hose with quick release coupling and 5m power cord with accessory plug for use inside vehicle.

• Suitable for inflating tyres on cars.

• Supplied in a storage bag with accessory kit including ball needle and adaptors for inflatables.

Model No. SEA MAC04D

*Please refer to www.sealey.co.uk/guarantee for more information on guarantees. TRX-STAR, TRX-TS and TRX-P tools are suitable for driving TORX® and TORX PLUS® fasteners respectively.

TORX® and TORX PLUS® are registered trademarks of Acument Intellectual Properties, LLC.

Promotion Valid Until 31.03.2021