NOTE: PLUMBER TO DETERMINE SEWER STACK LOCATION
elec. & hot/cold conduit for d/w
elec. conduit for ppt.to bench 135mm stepdown to garage
O/A
PROVIDE R2.0 WALL INSULATION BATTS. PROVIDE R5.0 CEILING INSULATION BATTS. PROVIDE R5.0 CEILING INSULATION BATTS TO GARAGE CEILING. GARAGE
MASTER BED.
ENS.
FAMILY/MEALS
A HANDRAIL MUST BE LOCATED AT LEAST ONE SIDE OF THE STAIR FLIGHT AND BE NO LESS THAN 865mm VERTICALLY ABOVE THE NOSING OF THE STAIR TREADS. HANDRAIL MUST BE CONTINUOUS AND HAVE NO OBSTRUCTIONS ON HANDHOLD, EXCEPT FOR NEWEL POSTS, BALL TYPE STANCHIONS OR THE LIKE; IN ACCORDANCE WITH PART 3.9.2.4 OF THE BUILDING CODE OF AUSTRALIA 2012.
ENS./W.I.R.
STAIR
HALL
X
STAIR
STAIR
ENTRY/MEALS B A06
STORE 6M3
dp
dp SHR.
ENS.
line of F.F. above
STORE
C A07
dp
PORCH PLASTER CEILING
step
L'DRY
PANTRY
LEGEND
dp
PORCH
LIN.
135mm stepdown to garage
P'DR
PIER
bulkhead @ 2340H
KITCHEN
KITCHEN
L'DRY
dp
gas meter concrete floor
broom
P'DR 1 line of F.F. above
beam to engineer's design + specification
GARAGE
dp
PORCH
sectional colorbond o/head door w/ remote
waterfall end
beam to engineer's design + specification
L'DRY
A A05
PIER
ENTRY
HALL
MEALS ENTRYLHALL
STAIR
STAIR
bulkhead @ 2340H
W.I.R.
GARAGE
PLASTER CEILING
D A08
sectional colorbond o/head door w/ remote
retaining wall to engineers' design
DIRECT WIRED SMOKE DETECTOR ARTICULATION JOINT CAPPED COLD WATER POINT (@300H TO REF. SPACE) CAPPED HOT WATER POINT OPENING IN WALL FOR PLUMBING RISER STACK INSPECTION OPENING CEILING EXHAUST FAN 25 L/SEC SWITCHED WITH LIGHT
STORE 6M3
2000L water tank dp
dp
O/A
FAMILY
O/A
MASTER BED.
PLASTER CEILING
FAMILY/MEALS/KITCHEN
plaster lined wall
FAMILY/MEALS
ENS.
ENS.
GARAGE
line of F.F. above
W.I.R.
MASTER BED.
GARAGE
SHR.
dp
HOT WATER SYSTEM TAP FLOOR WASTE CAPPED WASTE POINT CAPPED GAS POINT
ENTRY
KITCHEN
L'DRY
LIN.
MANHOLE 700x500 METER BOX WITH GAS METER UNDERNEATH
GARAGE
X
P'DR GARAGE
METER BOX GAS METER
O/A
PROVIDE R2.0 WALL INSULATION BATTS. PROVIDE R5.0 CEILING INSULATION BATTS. PROVIDE R5.0 CEILING INSULATION BATTS TO GARAGE CEILING. BED 2
STAIR
STAIR
ROBE
BED 3
P'DR
Y
A HANDRAIL MUST BE LOCATED AT LEAST ONE SIDE OF THE STAIR FLIGHT AND BE NO LESS THAN 865mm VERTICALLY ABOVE THE NOSING OF THE STAIR TREADS. HANDRAIL MUST BE CONTINUOUS AND HAVE NO OBSTRUCTIONS ON HANDHOLD, EXCEPT FOR NEWEL POSTS, BALL TYPE STANCHIONS OR THE LIKE; IN ACCORDANCE WITH PART 3.9.2.4 OF THE BUILDING CODE OF AUSTRALIA 2012.
ROBE
X
B A06
dp dp
dp/s
BED 3
O/A
ROBE
V. HALL
P'DR 2
ROBE
BATH
BATH
BED 4
BED 4
V.
dp
V.
V.
P'DR
HALL
C A07
ROBE
HALL P'DR
A A05 linen
STAIR STAIR
ROBE
STAIR
O/A
sliding doors 2300H
BED 3
BED 2
LINEN
BED 2
Y
ROBE
ROBE
sliding doors 2300H
LEGEND
dp
sliding doors 2300H dp/s
DIRECT WIRED SMOKE DETECTOR ARTICULATION JOINT
dp
CAPPED COLD WATER POINT (@300H TO REF. SPACE) CAPPED HOT WATER POINT D A08
OPENING IN WALL FOR PLUMBING RISER STACK INSPECTION OPENING CEILING EXHAUST FAN 25 L/SEC SWITCHED WITH LIGHT HOT WATER SYSTEM TAP FLOOR WASTE CAPPED WASTE POINT V.
P'DR
CAPPED GAS POINT
V.
MANHOLE 700x500 BATH
ROBE
BED 4
METER BOX WITH GAS METER UNDERNEATH METER BOX
O/A
X
GAS METER
rendered 75mm foamboard cladding
title boundary
title boundary
NOTE:SENSOR LIGHTS ABOVE FRONT ENTRY AND ABOVE GARAGE DOOR
roof tiles
eave off frame
25° ROOF PITCH
88.265 88.093
87.860
88.130
sectional garage door rendered brickwork MAX H. 1000MM SLEEPER RETAINING WALL
A
selected brickwork
MAX H. 1400MM SLEEPER RETAINING WALL
title boundary
rendered 75mm foamboard cladding
25° ROOF PITCH eave off frame
roof tiles
88.265 87.860 2000 L R/W TANK
WATER PUMP CONDENSER
MAX H. 1850MM SLEEPER RETAINING WALL
B
aluminium framed window
selected brickwork
MAX H. 1000MM SLEEPER RETAINING WALL
rendered 75mm foamboard cladding
eave off frame
roof tiles 25° ROOF PITCH
title boundary
title boundary
OBS max 25% transparency & fixed up to 1.7m from FFL (openable above 1.7m)
HWS
88.130
88.265
CONDENSER 2000 L R/W TANK
MAX H.2250MM SLEEPER RETAINING WALL
C
WATER PUMP
selected brickwork
aluminium framed window
MAX H.1850MM SLEEPER RETAINING WALL
NOTE:SENSOR LIGHTS ABOVE ABOVE GARAGE DOOR
roof tiles 25° ROOF PITCH
eave off frame
88.265
87.860
UNIT 1 GARAGE
D
rendered 75mm foamboard cladding
sectional garage door
title boundary
NOTE:SENSOR LIGHTS ABOVE FRONT ENTRY AND ABOVE GARAGE DOOR
88.130
timber front entry door
gas meter rendered brickwork
selected brickwork
2000 L R/W TANK MAX H. 2250MM SLEEPER RETAINING WALL
NOTE: ALL WINDOWS VIEWED FROM OUTSIDE
NOTE: OVERALL DEPTH OFF FRAME OF ALL WINDOWS IS 165MM I.E. WOODEN REVEAL + ALUMINIUM FRAME
OBSCURE
NOTE: ALL GLASS TO CONFORM WITH AS1288-2006: GLASS IN BUILDINGS
OBSCURE
EX 40 OUT
A
D
OBSCURE
OBSCURE
OBSCURE
OBSCURE
EX 40 IN
C
B
O/A
NOTES ON CABINET DETAILING
O/A
INFILL
CARCASS/ REF. SPACE
CARCASS
CARCASS
CARCASS
CARCASS
CARCASS
ALL END PANELS (EXCEPT AT SIDES OF UPRIGHT OVEN) TO BE CONCEALED BEHIND DOORS/DRAWERS AND IN LINE WITH CARCASS (I.E. DOORS CLOSE OVER)
INFILL
INFILL PANELS AT SIDES OF DOORS TO BE IN LINE WITH FRONT OF DOORS AND DRAWERS
glass s/back
waste bin
B'TOP & SUBSTRATE
waterfall end
s/s undermount sink
D/W
CARCASS
CARCASS
W/O
selected 40mm stone benchtop
INFILL AT TOP OF KITCHEN OVERHEAD DOORS (IF REQUIRED) TO BE IN LINE WITH CARCASS (I.E. SET BACK FROM DOOR FACE)
O/A B'TOP
SPLASHBACK
undermount rangehood
selected stone b'top
selected tap
CARCASS
M/O
REF.
REF. SPACE
CARCASS W/O SPACE M/O SPACE
CARCASS
CARCASS
TO SINK PANTRY
CARCASS
CARCASS
D/W SPACE CARCASS
B
INFILL
A
CARCASS
O/A BENCHTOP
CARCASS
CARCASS
CARCASS
CARCASS
CARCASS
M/O W/O
PANTRY
INFILL
CARCASS
bottom of carcass stepped up 5mm from door, carcass back and end panels CARCASS
DOOR
INFILL
REF. SPACE
CARCASS
REF. SPACE
REF. SPACE
INFILL
DRWS
DRWS
INFILL
DRWS
A
C
B
DRWS
D/W
CUP'D
DRWS
refer to base cupboard details O/A BENCHTOP
O/A BENCHTOP
CUP'D
O'HANG
DOOR, END PANEL & CARCASS BACK
CARCASS
B'TOP & SUBSTRATE CARCASS
O/A B'TOP
SPLASHBACK CARCASS
O/A BENCHTOP
CARCASS D/W SPACE
CARCASS
CARCASS
O/A BENCHTOP
C
O/A B'TOP
O'HANG
BULKHEAD
CARCASS
NOTES ON CABINET DETAILING
O/A B'TOP
BROOM CARCASS
bottom of carcass stepped up 5mm from door, carcass back and end panels
DOOR
CUP'D
O'HANG FROM CARCASS
B'TOP
CARCASS
DOOR
substrate fixed to carcass from underside only - NO fixing through top
door
RAIL
laminate kicker
O/A
stone benchtop
STONE O'HANG FROM CARCASS
O/A B'TOP
W/M SPACE
DRAWER O'HANG
B'TOP O/A DRAWERS
O/A B'TOP
TROUGH & SPOUT
CARCASS
B'TOP & SUBSTRATE
CARCASS
refer to overhead cupboard details
substrate fixed to carcass from underside only - NO fixing through top O'HANG FROM DOOR FRONT
CARCASS CARCASS
INFILL
O/A B'TOP
laminate kicker
A
SHADOW B'TOP LINE
O/A DOOR
CARCASS
O/A B'TOP
B'TOP & SUBSTRATE
laminate top
B'TOP
DOOR, END PANELS & CARCASS BACK
A
W/M SPACE
INFILL AT TOP OF KITCHEN OVERHEAD DOORS (IF REQUIRED) TO BE IN LINE WITH CARCASS (I.E. SET BACK FROM DOOR FACE)
O'HANG
CUP'D
W/M
INFILL PANELS AT SIDES OF DOORS TO BE IN LINE WITH FRONT OF DOORS AND DRAWERS
CARCASS
SHADOW LINE
O/A B'TOP
CARCASS
SUBSTRATE
W/M SPACE
ALL END PANELS (EXCEPT AT SIDES OF UPRIGHT OVEN) TO BE CONCEALED BEHIND DOORS/DRAWERS AND IN LINE WITH CARCASS (I.E. DOORS CLOSE OVER)
extent of tiling
extent of tiling
CARCASS
INFILL CARCASS
INFILL
CARCASS
O/A BENCHTOP
CARCASS
O/A BENCHTOP CARCASS
CARCASS
20mm shadowline
INFILL
O/A BENCHTOP
O/A BENCHTOP
BASIN & SPOUT
stone vanity top & return edge
CARCASS
INFILL
CARCASS CARCASS CARCASS
O/A BENCHTOP
KICKER SETBACK
KICKER SETBACK
KICKER
AS PER ELEV. TO MIRROR EDGE
O/A DOOR
CARCASS
O'HANG FROM DOOR FRONT
KICKER
laminate kicker
counter top basin O/A BENCHTOP
KICKER
adjustable shelf
O/A DOOR
CARCASS
TO BASIN
AS PER ELEV.
substrate fixed to carcass from underside only - NO fixing through top
backing board to arrised mirror edge. 16mm edged melamine board by cabinet makers
B'TOP
SHADOW LINE
O/A B'TOP
BENCHTOP
BENCH
O/A BENCHTOP
MIRROR PLAN VIEW
adjustable shelf laminate kicker KICKER
NOTES ON WET AREA CABINET DETAILING CARCASS DOOR
CARCASS DOOR
ALL END PANELS TO BE CONCEALED BEHIND DOORS/DRAWERS AND IN LINE WITH CARCASS (I.E. DOORS CLOSE OVER) INFILL PANELS AT SIDES OF DOORS TO BE IN LINE WITH DOORS AND DRAWERS INFILL AT TOP OF OVERHEAD DOORS (IF REQUIRED) TO BE IN LINE WITH CARCASS (I.E. SET BACK FROM DOOR FACE)
CARCASS
BASIN & SPOUT
BASIN & SPOUT
CARCASS INFILL
O/A BENCHTOP
O/A BENCHTOP
BASIN & SPOUT
1409w x 1100h polished edge mirror on backing board
875 x 1100h polished edge mirror on backing board
1085w x 1100h polished edge mirror on backing board
O/A BENCHTOP
1545w x 1100h polished edge mirror on backing board
LIGHTING LEGEND
GENERAL NOTES ALL LED DOWNLIGHTS TO BE SUPPLIED BY ELECTRICIAN
ELECTRICAL LEGEND 10A 10A 10A DOUBLE POWER POINT @1350mm
CEILING BATTEN LIGHT FITTING (15w) EXT. WALL MOUNTED LIGHT FITTING @1800 HIGH (15w)
10A 10A SINGLE POWER POINT @1350mm
HANGING PENDANT LIGHT FITTING (15w)
10A 10A SINGLE POWER POINT @300mm
1200
SINGLE FLUORESCENT LIGHT (1200) (36w)
10A WP DOUBLE EXTERNAL POWER POINT
ALL SINGLE & DOUBLE POWERPOINTS FOR ISLAND BENCH @750MM
1200
DOUBLE FLUORESCENT LIGHT (1200) (36w)
ALL POWERPOINTS ABOVE WALL BENCHTOP @1100MM
600
DOUBLE FLUORESCENT LIGHT (600) (36w)
LIGHTING FOR KITCHEN CABINETRY REFER TO KITCHEN INTERNAL DRAWINGS FOR LIGHTING LOCATIONS
NOTES ON ALL KITCHEN POWER OUTLETS
10A DOUBLE POWER POINT @1350mm 10A DOUBLE POWER POINT @300mm
400
STORE 6M3
RANGEHOOD POWERPOINT @1800MM
10A DOUBLE EXTERNAL POWER POINT @1100mm
FLUORESCENT LIGHT 10A WP SINGLE EXTERNAL POWER POINT
REFRIGERATOR POWERPOINT @1500MM
SINGLE PARA FLOOD LIGHT (100w) DOUBLE PARA FLOOD LIGHT (200w) 1200
INT. WALL LIGHT BATTEN HOLDER @2100 (15w)
ENS.
2-way switch to unit 1
GARAGE
MASTER BED.
11.5
11.5
LIGHT OUTLET & SINGLE POWER POINT TO ROOF
11.5
quad plate
ceiling mounted for garage remote
FAMILY 11.5
1200
11.5
C9
LED CABINET DOWNLIGHT (9w)
11.5
LED DOWNLIGHT (12w)
9
W.I.R.
STEP LIGHTING @300mm ABOVE TREAD (90x90) (20w) 11.5
S 11.5
MEALS
@750h for d/w
11.5
11.5
11.5
11.5
11.5
DIMMER SWITCH @1350mm
11.5
11.5
@1500h for w/m
11.5
@750h 11.5
400
C9
C9
L'DRY
@750h for h/p
1200
@1200h for w/o on sep. circuit
ceiling mounted for garage remote
@1500h for ref.
P'DR 1
@1500h for r/h
15A EXT POWER POINT FOR SINGLE PHASE CONDENSER 3 PHASE POWER POINT FOR A/C UNIT CEILING EXHAUST FAN 25 L/SEC SWITCHED WITH LIGHT DIRECT WIRED SMOKE DETECTOR CEILING EXHAUST FAN WITHOUT DRAFT STOPPERS
4 LIGHT/FAN/HEATER COMBO
CEILING EXHAUST FAN WITH DRAFT STOPPERS
2 LIGHT/FAN/HEATER COMBO
FUSE BOX
11.5
GAS METER DATA / FIBRE OPTIC POINT TELEPHONE POINT MOVEMENT SENSOR
broom
PANTRY
SINGLE POWER POINT @1200mm ON SEPARATE CIRCUIT FOR WALL OVEN
JUNCTION BOX @2000mm APPROX.
@1500h for m/o
11.5
10A POWER POINT FOR SECURITY SYSTEM
METER BOX @1900 TO TOP
11.5
KITCHEN PORCH
LED DOWNLIGHT (9w)
10A SINGLE POWER POINT @300mm S
PROVISION FOR SEPARATE POWERPOINTS FOR WALL OVEN TOWER
TELEVISION ANTENNA POINT
HVAC LEGEND ADD-ON REFRIGERATIVE AIR CONDITIONING UNIT
GARAGE
CEILING HEATING OUTLET 400
HEATING THERMOSTAT HEATING UNIT (LOCATED IN CEILING)
STORE
RETURN AIR EVAPORATIVE COOLING OUTLET EVAPORATIVE COOLING UNIT LOCATION HOT WATER SYSTEM LOCATION
LIGHTING CALCULATOR Internal House Area (NOT incl. garage, alfresco etc.) Maximum Wattage Permitted (MAX 5w p/m2)
180 m2 900W Total Watts
- Where external lights are provided, all external lights to have a daylight sensor - Owners to ensure that all future external lighting is to have an average of 40 lumens/W
ROOF ACCESS Watts 0
RINNAI INFINITY CONTROL POINT 0
LIGHTING LEGEND
GENERAL NOTES ALL 12 VOLT DOWNLIGHTS TO BE SUPPLIED BY ELECTRICIAN
ELECTRICAL LEGEND 10A 10A 10A DOUBLE POWER POINT @1350mm
CEILING BATTEN LIGHT FITTING (15w) EXT. WALL MOUNTED LIGHT FITTING @1800 HIGH (15w)
10A 10A SINGLE POWER POINT @1350mm
HANGING PENDANT LIGHT FITTING (15w)
10A 10A SINGLE POWER POINT @300mm
1200
SINGLE FLUORESCENT LIGHT (1200) (36w)
10A WP DOUBLE EXTERNAL POWER POINT
ALL SINGLE & DOUBLE POWERPOINTS FOR ISLAND BENCH @750MM
1200
DOUBLE FLUORESCENT LIGHT (1200) (36w)
ALL POWERPOINTS ABOVE WALL BENCHTOP @1100MM
600
DOUBLE FLUORESCENT LIGHT (600) (36w)
LIGHTING FOR KITCHEN CABINETRY REFER TO KITCHEN INTERNAL DRAWINGS FOR LIGHTING LOCATIONS
NOTES ON ALL KITCHEN POWER OUTLETS
10A DOUBLE EXTERNAL POWER POINT @1100mm 10A DOUBLE POWER POINT @1350mm 10A DOUBLE POWER POINT @300mm
400
RANGEHOOD POWERPOINT @1800MM
FLUORESCENT LIGHT 10A WP SINGLE EXTERNAL POWER POINT
REFRIGERATOR POWERPOINT @1500MM
SINGLE PARA FLOOD LIGHT (100w) DOUBLE PARA FLOOD LIGHT (200w) INT. WALL LIGHT BATTEN HOLDER @2100 (15w) LIGHT OUTLET & SINGLE POWER POINT TO ROOF
BED 3
ROBE
BED 2
C9
LED CABINET DOWNLIGHT (9w)
11.5
LED DOWNLIGHT (12w)
9
STEP LIGHTING @300mm ABOVE TREAD (90x90) (20w)
ROBE
11.5 11.5
P'DR 2
linen
DIMMER SWITCH @1350mm 11.5
11.5
LED DOWNLIGHT (9w)
10A SINGLE POWER POINT @300mm S
PROVISION FOR SEPARATE POWERPOINTS FOR WALL OVEN TOWER
10A POWER POINT FOR SECURITY SYSTEM SINGLE POWER POINT @1200mm ON SEPARATE CIRCUIT FOR WALL OVEN 15A EXT POWER POINT FOR SINGLE PHASE CONDENSER 3 PHASE POWER POINT FOR A/C UNIT CEILING EXHAUST FAN 25 L/SEC SWITCHED WITH LIGHT DIRECT WIRED SMOKE DETECTOR CEILING EXHAUST FAN WITHOUT DRAFT STOPPERS
4 LIGHT/FAN/HEATER COMBO
CEILING EXHAUST FAN WITH DRAFT STOPPERS
2 LIGHT/FAN/HEATER COMBO
FUSE BOX
11.5
JUNCTION BOX @2000mm APPROX. METER BOX @1900 TO TOP GAS METER
BED 4 11.5
ROBE
BATH
DATA / FIBRE OPTIC POINT TELEPHONE POINT MOVEMENT SENSOR TELEVISION ANTENNA POINT
HVAC LEGEND ADD-ON REFRIGERATIVE AIR CONDITIONING UNIT CEILING HEATING OUTLET HEATING THERMOSTAT HEATING UNIT (LOCATED IN CEILING) RETURN AIR EVAPORATIVE COOLING OUTLET EVAPORATIVE COOLING UNIT LOCATION HOT WATER SYSTEM LOCATION
LIGHTING CALCULATOR Internal House Area (NOT incl. garage, alfresco etc.) Maximum Wattage Permitted (MAX 5w p/m2)
180 m2 900W Total Watts
- Where external lights are provided, all external lights to have a daylight sensor - Owners to ensure that all future external lighting is to have an average of 40 lumens/W
ROOF ACCESS Watts 0
RINNAI INFINITY CONTROL POINT 0
NOTE: REFER TO ENGINEER'S FOOTING DESIGN
FLASHING
BOX GUTTER timber roof trusses to manufacturer's specifications
roof tiles at 25 deg. pitch
roof tiles at 25 deg. pitch
HALL
BED 2
BATH TIMBER CLEAT
KITCHEN ENS.
W.I.R.
GARAGE
STORE
50MM THICK ACOUSTIC INSULATION EXTENDING 600MM BOTH SIDES (REQUIRED FOR FLANKING SOUND CONTROL)
PLASTER
GARAGE 50MM THICK ACOUSTIC INSULATION
A
B
50MM THICK ACOUSTIC INSULATION EXTENDING 600MM BOTH SIDES (REQUIRED FOR FLANKING SOUND CONTROL)
TRUSSES PROVIDE FULL HT. ARTICULATION JOINT (FOOTING TO EAVE) AT 6m MAX CENTRES. (UNLESS STATED IN SOIL REPORT) (SEE DETAIL BELOW)
CLOSED CELL POLYETHYLENE JOINT FILLER
METAL GUTTER
METAL FASCIA
A
PLASTER
ROOF TRUSS AS PER MANUFACTURERS SPEC. TERRACOTTA TILED ROOF
B G.S. SPOUTING
BACKING PLATE FOR FIXING OF GUTTER & FLASHING.
C
FASCIA
SELECTED PLASTER CORNICE
METAL FLASHING FIXED TO PITCHING BEAM PRIOR TO INSTALLAION OF FASCIA