CONSTRUCTION DESIGN - Western Bace Axonometric Cutaway

Page 1

WESTERN BACE

6 DEGREES ARCHITECTS

SECTION O AXONOMETRIC drawing no.

D101

scale

1:20 @ A0

KATERINA KARADIMAS

N

699244

5.6

5.5

4.3

5.4

5.1

5.3 7.1

5.2

7.4

8.4

8.3

FOUNDATIONS AND SUB-STRUCTURE 1.1 2000 x 2000 pad footing transfers load to foundation; N16 steel reinforcement top and N20 below resist cupping action from portal frame point load with column starter bars cast into place

4.2

6.3 7.2

1.2 450mm strip footing with 4-L12 top and bottom; R6 ligatures at 750 cts. prevent bending action from compressive load 1.3 Unreinforced mass concrete 15MPa at varying depths, poured to depth of basalt provides an even level of known compressive strength for the construction of the footings

2.3

1.4 Green star compliant concrete slab with min. 32MPa compressive strength cast over 100 min sacrificial cardboard void formers (and polyethylene membrane) 1.5 Concrete ramp at 1:20 gradient

3.2 3.3

8.2 4.4

4.1

GROUND FLOOR MASS STRUCTURE

3.4

2.1 190mm Boral 'Designer Block' wall, corefilled at 400 cts. (every second core) - N16 starter bars project 900min into strip footing below 2.2 190mm Boral 'Designer Block' wall, corefilled with 70mm cavity R2.4 foilboard and 90mm Boral 'Designer Block' skin (textured blocks cut on site to create design feature) 2.3 Precast concrete column (behind) by Westkon Precast Pty. Ltd. craned into place, grout tubes aligned with starter bars and filled to form rigid connection

8.1 3.1

2.1

8.6

FIRST FLOOR MASS STRUCTURE 3.1 Precast reinforced concrete beams by Westkon Precast Pty. Ltd. with cast-in N12 ligatures; N20 bars connect beam to hollowcore panels 3.2 Precast hollowcore concrete panels by Westkon Precast Pty. with 27% min OPC substitution for Greenstar compliance

6.2

3.3 Hydronic heating tubes tied to square mesh - elevated with bar chairs for screed pour 3.4 30 MPa screed completes connection between beam and slab panels

8.5 7.3

STRUCTURAL STEEL 4.1 All members prefabricated with cleat plates and/or bolt holes for quick on-site connection; services openings prefabricated as required

2.2

1.1

0-150 admixed silt, clay, crushed basalt

6.1

4.2 150PFC with welded plate act as window head + sill members 4.3 C100 12 girts act as secondary framing members; R4.5 insulation between

150-1500 silty clay, high plasticity

4.4 Bridge truss prefabricated with welded connections

ROOF 5.1 Exposed laminated supporting beams by LTS; bolted connection via 10 plate bracket to precast columns with cast-in M20 ferrules 5.2 1 HJ24090 Hyjoists by Carter Holt Harvey; with packers as required for roof pitch 5.3 MGP12 primary battens at 1200 cts. from Greenstar approved source; batten screws connect to joists where packer <=45mm, otherwise galvanised nails used

1.4 1.5 1500 basalt rock

5.4 MGP12 secondary battens at 900 cts. fixed using 75 long batten screws 5.5 75mm R2.6 'Spacemaker' insulated roof panels by Versiclad 5.6 PVC panels

1.2

DOORS + WINDOWS 6.1 'Series 826 Thermally Broken FrontGLAZE' window and door frame system from AWS; aluminium with square beading and anodised finish 6.2 'Series 826 Thermally Broken Door System' door from AWS; double glazed with square beading and anodised finish 6.3 'ThermoTech' insulating glass unit from Viridian; low E coated, double glazd with 12mm gap

WATERPROOFING 7.1 Folded 0.7mm Cor-Ten steel capping and flashing with 20mm dripline 7.2 Folded 0.7mm Cor-Ten steel window capping/sub-sill with 20mm R0.2 thermal break rigid insulation 7.3 Folded 1.5mm anodised aluminium capping 7.4 Fabricated from 0.8 Zincalume steel at 1:50 min fall; no fixings, held in place via flashings and fit on 19mm waterproof plywood with breathable membrane

FINISHES 8.1 Archlad 'Express Panels with 294 Face' - folded 0.7mm Cor-ten panels with breathable waterproof membrane to prevent moisture ingress 8.2 Remilled recycled 135 x 35mm Spotted Gum timber decking from Urban Salvage - screw fixed and Greenstar approved 8.3 40 x 40mm Western Red Cedar timber battens from Cedar Sales - screw fixed and Greenstar approved 8.4 'Webglass GC' translucent polyester sheeting from Ampelite; 'Klip-Lok 700' profile connected by manufacturer specific fixing clips 8.5 7.3mm 'Envisions' cut pile nylon carpet from Ontera; GBCA compliant with polymer fibreglass reinforced backing 8.6 15mm MDF panel from Austral Plywoods or Gunnersuns; BCA Group 1 fire rated as required for commercial construction to slow down fire spreading in an emergency

1.3


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.