University of Alaska Building 7 Report

Figure 2.59 Displacement (inches) of the floor system surrounding Column 79. 2.6.2 ABAQUS Analysis Figure 2.60 is a three-dimensional depiction of our ABAQUS model for Floors 12 and 13. The Floor 12 x-direction movement is shown in Figure 2.61. The Floor 13 x-direction movement is shown in Figure 2.62. The x-direction movement around Column 79 is shown in Figure 2.63. The x-direction movement of the floor system surrounding Column 79 was found to be 1.85 inches, and the y-direction movement was found to be 0.94 inches. Prior to modeling a given floor or two floor system, the UAF research team examined column stiffness between floors; this resulted in springs to accommodate floor framing above and below a given number of floors. The UAF team subsequently introduced axial and transverse column stiffness between floors 12 and 13, see Figure 2.60. This was also verified by including both floors 12 and 13 in a separate model (not shown) and in that model, the column stiffness below floor 12 and above floor 13 were included. The results were compared as a quality control check on our modeling methodology.

University of Alaska Building 7 Report

Articles inside

REFERENCES

Figure 4.20 Velocity comparison between Chandler measurement (green plotted line) and UAF simulation (red plotted line). Bold green trend line illustrates free fall

Figure 4.17 (a) Comparison of simulated collapse to perspective 1; (b) comparison of simulated collapse to perspective 2

2.7 Summary and Conclusion

3.2.2 Girder A2001 Web Stiffeners Prevent Flange Failure and Girder Walk-off

Table 2.3 Comparison of UAF and NIST Modeling

4.6 Results of Core Column/Exterior Column Failure Analysis

2.6.2 ABAQUS Analysis

3.2.3 Lateral Support Beams Prevent Beam Buckling

2.6.1 SAP2000 Thermal Deformation Analysis

Figure 2.36 Modeling process for a beam to girder shear connector, “STC.”

Table 2.1 Column loading for the Floor 12 and 13 assembly

Figure 2.21 SAP2000 model of entire WTC 7 without roof

Figure 2.24 Column number layout of Floor 13 (NIST, 2008, NCSTAR 1A

Figure 2.26 Small section of typical floor slab of WTC 7 with finer meshing

Figure 2.29 Plan View: Model of floor slabs in strong direction (parallel to flutes

Figure 2.46 Seated moment connection of exterior girders to exterior columns ABAQUS model

2.2 Solid Works Modeling

2.1.3 Background Studies

1.5.3 Approach 3: Simulating the Collapse of WTC 7

Figure 2.5 Area of floor where connection failure was modeled by NIST

1.5.2 Approach 2: Evaluation of NIST’s Collapse Initiation Hypothesis

Figure 2.6 Progressive collapse separated into two parts

Figure 2.3 Approach used to model buckled beams in LS-DYNA model (NIST, 2008, NCSTAR 1-9, Vol. 2

1.4.3 Arup and Nordenson, April 2010

Figure E.3 Finite Element Model of WTC7 in SAP2000, as viewed from the south

Figure 1.6 WTC 7 was in free fall for approximately 2.25 seconds over a distance of approximately 8 stories or 32.0 meters (NIST, 2008, NCSTAR 1A

EXECUTIVE SUMMARY

2.2 Hypothetical Failure Mechanisms for West Penthouse and North Face Roofline

Figure 1.4 WTC 7 tenants on September 11, 2001 (FEMA, 2002

Figure 1.9 WTC 7 steel frame building geometry prior to its collapse (FEMA, 2002

Figure 1.5 The collapse of WTC 7 at 5:20 PM (source unknown

1.4.2 National Institute of Standards and Technology, November 2008