Comeco-GTS other by Naeem Aziz

actuators and heaters Low-cost 1-phase AC Relay SSRP ♦ ♦ ♦ ♦ ♦ ♦

Zero-cross output switching Up to 275 VAC operating voltage 10 A, 16 A, 25 A, or 40 A switching RMS current 4 input ranges 4000 V input / output insulation Heatsinks available

The SSRP solid state relay is a zero-cross operating electronic module designed to switch single-phase AC power loads. Thanks to its higher switching frequency and practically complete absence of electromagnetic interference, the SSR module is a non-contact and convenient substitute of power contact relays. The life and reliability of the SSR module, compared to these of the contact relays, are much higher because there are no moving parts, noise, shocks, and vibration during the operation. SSRP can switch active or small inductive loads from 10 to 40 A at power voltage up to 275 VAC. The control input is optically isolated from the output and accepts AC or DC voltage signals. An operating LED indicates ON/OFF device status. Heatsinks are available as accessory.

Technical specifications Input

General specifications

Control voltage Input current Turn-on / off voltage Reverse voltage protection

Output

(no connection with the input types!)

On-state current at proper heatsink (1) ≤ 10 Arms ≤ 16 Arms ≤ 25 Arms ≤ 40 Arms Minimum holding current 50 mA 80 mA 50 mA 80 mA Non-rep. surge current at t = 20 ms 160 A 400 A 100 A 250 A Maximum leakage current 2 mA 5 mA 1 mA 3 mA Critical rate of current rise dI/dt 50 A/μs 50 A/μs 50 A/μs 50 A/μs I2t value for fusing at t = 10 ms 78 A2s 78 A2s 78 A2s 78 A2s On-state voltage at rated current 1.6 Vrms 1.6 Vrms 1.6 Vrms 1.6 Vrms Critical off-state voltage rise dV/dt 400 V/μs 400 V/μs 500 V/μs 500 V/μs Operational frequency 45...65 Hz 45...65 Hz 45...65 Hz 45...65 Hz Thermal resistance (junction-case) 2.3 °C/W 2.1 °C/W 1.1 °C/W 1.2 °C/W (1) (2)

min. 24...max. 275 VACrms 600 Vp 700 Vp > 0.6 -20...65 °C -40...85 °C glass-filled plastic aluminum 4000 VACrms 2500 VACrms IP00 4 x M4 screws 2 x M4 screws MAC2 rail clamp (2) ø3, red ≈ 100 g

Operating AC voltage Rep. off-state peak voltage Non-rep. off-state peak voltage Power factor Operating temperature Storage temperature Case material Base plate (heatsink) material Input / output insulation Output / case insulation Protection class Wiring Mounting Rail mounting ON-indicating LED Weight

4...36 VDC 6...26 VAC/DC 115 VAC 230 VAC 6...12 mA 12 mA 5...12 mA 6 mA 3 VDC 4 VAC / 5 VDC 90 VAC 180 VAC -32 VDC -32 VDC -

We highly recommend using SSR at no more than 80% of maximum on-state current! Ordered separately (see 'Accessories') 22

30 12 FUSE

LOAD

4.3

Heatsink specifications Heatsink surface [cm2] / length [mm] (at 85 °C heatsink temperature) SSRP variant Current Æ Ambient temperature È

10 A

16 A

15 A

20 A

40 25 A

20 A

40 A

20 °C

72 / 62

60 / 62

214 / 62

134 / 62

287 / 62

499 / 62

237 / 62

607 / 62

1280 / 120

40 °C

150 / 62

124 / 62

445 / 62

278 / 62

601 / 62

1041 / 100

494 / 62

1275 / 120

2668 / 250

60 °C

485 / 62

400 / 62

1435 / 135

907 / 85

1924 / 180

Ordering code

1600 / 150

SSRP - G1

Code Feature or option

Code values

Variant

10, 16, 25, 40

Input

A - 230 VAC, B - 115 VAC, D - 4…36 VDC, Е - 6…26 VAC/DC

Applicable accessories Code Description HS__

30 A

Heatsink (specify the length [mm] using the table above) w/ or w/o rail-mounting clamp (2)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

AC VOLTAGE

CONTROL VOLTAGE

68 56

actuators and heaters 1-phase AC Relay for Inductive Loads SSRQ ♦ ♦ ♦ ♦ ♦ ♦

Designed for all types of loads up to 400 VAC Zero-cross output switching 10 A or 16 A switching RMS current 4 input ranges 4000 V input/output insulation Heatsinks available

The SSRQ solid state relay is a zero-cross operating electronic module designed to switch single-phase AC power loads. Since there are no moving parts, noise, shocks, and vibration during the operation, the life and reliability of the SSR module, compared to these of the contact relays, are much higher. Thanks to a snubberless™ triac, SSRQ can switch both active and inductive loads up to 16 A at power voltage up to 400 VAC. The control input is optically isolated from the output and accepts AC or DC voltage signals.

Technical specifications Input

General specifications

Control voltage Input current Turn-on/off voltage Reverse voltage protection

4...36 VDC 6...26 VAC/DC 115 VAC 230 VAC 6...12 mA 12 mA 5...12 mA 6 mA 3 VDC 4 VAC / 5 VDC 90 VAC 180 VAC -32 VDC -32 VDC (no connection with the input types!)

Output On-state current at proper heatsink (1) Minimum holding current Non-rep. surge current at t = 20 ms Maximum leakage current Critical rate of current rise dI/dt I2t value for fusing at t = 10 ms On-state voltage at rated current Critical off-state voltage rise dV/dt Operational frequency Thermal resistance (junction-case) (1) (2)

≤ 16 Arms 50 mA 160 A 2 mA 50 A/μs 78 A2s 1.6 Vrms 400 V/μs 45...65 Hz 2.1 °C/W

≤ 10 Arms 50 mA 100 A 1 mA 50 A/μs 78 A2s 1.6 Vrms 400 V/μs 45...65 Hz 2.3 °C/W

400 VACrms 24 VACrms 800 Vp 900 Vp -20...65 °C -40...85 °C glass-filled plastic aluminum 4000 VACrms 2500 VACrms IP00 4 x M4 screws 2 x M4 screws MAC2 rail clamp (2) ø3, red ≈ 100 g

Maximum operating AC voltage Minimum operating AC voltage Rep. off-state peak voltage Non-rep. off-state peak voltage Ambient temperature Storage temperature Case material Base plate (heatsink) material Input/output insulation Output/case insulation Protection class Wiring Mounting Rail mounting ON-indicating LED Weight

We highly recommend using SSR at no more than 80% of maximum on-state current! Ordered separately (see 'Accessories') 22

30 12 1

FUSE

+ 3

AC VOLTAGE

CONTROL VOLTAGE

68 56

LOAD

4.3

SSRQ variant

Current Æ Ambient temperature È

10 A

16 10 A

20 °C

72 / 62

60 / 62

214 / 62

40 °C

150 / 62

124 / 62

445 / 62

485 / 62

400 / 62

1435 / 135

60 °C

Ordering code

SSRQ - G1

Code Feature or option

Code values

Variant

10, 16

Input

A - 230 VAC, B - 115 VAC, D - 4…36 VDC, Е - 6…26 VAC/DC

Applicable accessories Code Description HS__

16 A

Heatsink (specify the length [mm] using the table above) w/ or w/o rail-mounting clamp (2)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Heatsink specifications Heatsink surface [cm2] / length [mm] (at 85 °C heatsink temperature)

actuators and heaters Low-cost DC Relay SSRD ♦ ♦ ♦ ♦ ♦ ♦

For DC loads Up to 300 VDC operating voltage Up to 40 A switching DC current 4 input ranges 4000 V input/output insulation Heatsinks available

The SSRD solid state relay is an electronic module designed to switch active or active/inductive DC power loads from 5 to 40 A at power voltage up to 300 VDC. Thanks to its higher switching frequency and practically complete absence of electromagnetic interference, the SSR module is a non-contact and convenient substitute of power contact relays. The life and reliability of the SSR module, compared to these of the contact relays, are much higher because there are no moving parts, noise, shocks, and vibration during the operation. The control input is optically isolated from the output and accepts AC or DC voltage signals. An operating LED indicates ON/OFF device status. Heatsinks are available as accessory.

Technical specifications Input

General specifications

Control voltage Input current Turn-on / off voltage Reverse voltage protection

4...36 VDC 6...26 VAC/DC 115 VAC 230 VAC 6...12 mA 12 mA 5...12 mA 6 mA 3 VDC 4 VAC / 5 VDC 90 VAC 180 VAC -32 VDC -32 VDC -

Output Operating DC voltage On-state current at proper heatsink (1) Non-repetitive pulse current Maximum leakage current On-state voltage at rated current Critical off-state voltage rise dV/dt Thermal resistance (junction-case) Power factor (1) (2)

-20...65 °C -40...85 °C glass-filled plastic aluminum 4000 VACrms 2500 VACrms IP00 4 x M4 screws 2 x M4 screws MAC2 rail clamp (2) ø3, red ≈ 100 g

Operating temperature Storage temperature Case material Base plate (heatsink) material Input / output insulation Output / case insulation Protection class Wiring Mounting Rail mounting ON-indicating LED Weight

(no connection with the input types!) 3...40 VDC 15...60 VDC 15...300 VDC ≤5A ≤ 20 A ≤ 40 A ≤ 15 A ≤ 130 A ≤ 160 A 10 μA 100 μA 100 μA 0.5 V 2V 1.3 V 400 V/μs 7 V/ns 15 V/ns 2.7 °C/W 1.6 °C/W 0.5 °C/W > 0.6 > 0.6 > 0.7

We highly recommend using SSR at no more than 80% of maximum on-state current! Ordered separately (see 'Accessories') 22

68 56

30 12

4.3

SSRD variant Current Æ

20 A

30 A

20 °C

40 °C

60 °C

Ambient temperature È

Ordering code

3 40 A

10 A

16 A

120

250

120

250

SSRD - G1

Code Feature or option

Code values

Variant

1, 2, 3

Input

A - 230 VAC, B - 115 VAC, D - 4…36 VDC, Е - 6…26 VAC/DC

Applicable accessories Code Description HS__

Heatsink (specify the length [mm] using the table above) w/ or w/o rail-mounting clamp (2)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

20 A

COMECO reserves the right of changing specifications without prior notice!

Heatsink specifications Heatsink length [mm] (at 85 °C heatsink temperature)

actuators and heaters 1-phase Power AC Relay SSRT ♦ ♦ ♦ ♦ ♦ ♦

Zero-cross output operation Double thyristor output switch Up to 400 VAC operating voltage Up to 200 A switching RMS current 4 input ranges 4000 V input/output insulation

The SSRT solid state relay is a zero-cross operating electronic module designed to switch single-phase AC power loads. Thanks to its higher switching frequency and practically complete absence of electromagnetic interference, the SSR module is a non-contact and convenient substitute of power contact relays. The life and reliability of the SSR module, compared to these of the contact relays, are much higher because there are no moving parts, noise, shocks, and vibration during the operation. The SSRT electronic relays can switch active loads up to 200 Arms and inductive loads up to 95 Arms at power voltage up to 400 VAC. The control input is optically isolated from the output and accepts AC or DC voltage signals. An operating LED indicates ON/OFF device status.

Technical specifications Input

General specifications

Control voltage Input current Turn-on/off voltage Reverse voltage protection

4...36 VDC 6...26 VAC/DC 115 VAC 230 VAC 6...12 mA 12 mA 5...12 mA 6 mA 3 VDC 4 VAC / 5 VDC 90 VAC 180 VAC -32 VDC -32 VDC -

Output ≤ 200 Arms

AC switching current at proper heatsink (1) Minimum holding current Non-rep. surge current at t = 10 ms Maximum leakage current Critical rate of current rise dI/dt I2t value for fusing at t = 10 ms On-state voltage at rated current Critical off-state voltage rise dV/dt Operational frequency Thermal resistance (junction-case) (1) (2)

200 mA 1700 A 15 mA 150 A/μs 1125 A2s 1.6 Vrms 500 V/μs 45...65 Hz 0.14 °C/W

min. 24...max. 400 VACrms 1200 Vp 1300 Vp > 0.5 -20...65 °C -40...85 °C aluminum, 150 mm long 4000 VACrms 2500 VACrms IP00 screw terminals 3 x M5 screws for optimized cooling MAC2 rail clamp (2) ø3, red max. 350 g (w/ standard heatsink)

Operating AC voltage Rep. off-state peak voltage Non-rep. off-state peak voltage Power factor Operating temperature Storage temperature Standard heatsink Input/output insulation Output/case insulation Protection class Input wiring Output wiring Mounting Rail mounting ON-indicating LED Weight

We highly recommend using SSR at no more than 80% of maximum on-state current! Ordered separately (see 'Accessories')

FUSE 3

AC VOLTAGE

+ 4

LOAD

Heatsink specifications Heatsink surface [cm2] / length [mm] (at 105 °C heatsink temperature) Max. RMS current Æ Ambient temperature È 20 °C

(3)

40 A

60 A

80 A

100 A

430 / 150

1300 / 150

1900 / 180

3800 / 350

40 °C

720 / 150

2100 / 200

3300 / 310

60 °C

1500 / 150

4400 / 410

6900 / (3)

6500 /

120 A

(3)

13500 / (3)

Requires additional forced (fan) cooling!

Ordering code

SSRT - G1

Code Feature or option G1

Input

Code values A - 230 VAC, B - 115 VAC, D - 4…36 VDC, Е - 6…26 VAC/DC

Applicable accessories Code Description HS__

Heatsink (specify the length [mm] using the table above) w/ or w/o rail-mounting clamp (2)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

5800 / (3) 10000 / (3) 20400 / (3)

COMECO reserves the right of changing specifications without prior notice!

CONTROL VOLTAGE

other control instrumentation Switch-mode Power Supply TC60P ♦ ♦ ♦ ♦

11-pin box for DIN-rail mounting Output power up to 5.5 W 90...250 VAC/DC SMPS Up to 2 independent stabilized output voltages

Technical specifications Input

Accuracy

Voltage Frequency Turn-on voltage Efficiency

90...250 V 47...440 Hz ≥ 85 VAC 76%, typical

Outputs

(up to 2 outputs) 1(2) x 24 VDC ≤ 0.23 A ≤ 5.5 W > 240 mV 4.0 kV 100 MΩ at 500 V

DC voltage Rated current Rated power AC voltage ripple Isolation voltage Isolation resistance

Protection 0.1 A 30 V ± 8% 105%

Front-panel fuse Over voltage Over load (1)

Operating conditions Operating temperature Operating humidity

-20...70 °C 0...85 %RH, non-condensing

Design and materials Case material Wiring Mounting Dimensions Weight Protection, front/terminals

plastic socket UNDECAL (1) in socket or on 35 mm DIN rail 35x78x91 mm max. 200 g IP44 / IP20

TC60P - G11G11

Code Feature or option G11

Output voltage (2)

Code values X - none (3), 24 - 24 VDC, Z - other (specify!)

Output supply voltages must be identical. At least one output must be ordered!

COMECO reserves the right of changing specifications without prior notice!

(3)

< ± 1.0% < ± 0.5% < ± 0.5% < 0.03% for 1 °C

Ordered separately (see Accessories)

Ordering code

(2)

Voltage tolerance Line regulation Load regulation Temperature drift

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

other control instrumentation Interface Adapter IA100 ♦ ♦ ♦ ♦ ♦

Universal RS485 to RS232 converter Designed for all COMECO devices equipped with RS485 Data acquisition from up to 32 net devices Suitable for COMECO "PolyMonitor" software Low cost

The IA100 interface adapter is a simple electronic device, designed to support the "PolyMonitor" multi-point data-acquisition software applicable for configuration and data collecting from a network of various COMECO control devices with RS485 interface and net addresses. IA100 supports up to 32 devices, connected into a RS485 net as well as the RS232 communication with PC or operating station. The information collected during the data-acquisition process can be stored, viewed, printed, and further processed through the "PolyMonitor" program or via customer-developed PC software based on the free communication protocols of the COMECO network devices.

Technical specifications 'Input' interface

Power supply

Interface type Function Supported net devices Format Baud rate

RS485 net control and data acquisition up to 32 8 (data) + 1 (stop), even parity max. 9600 bps

'Output' interface Interface type Function Format Baud rate

RS232 connection to PC 8 (data) + 1 (stop), none parity 9600 bps

Software "PolyMonitor" (1)

Data acquisition

Accessories custom made K6 (1)

RS485 input cable RS232 output cable

9 VAC/DC included max. 90 mA LED for power ON

Operating conditions Operating temperature Operating humidity

0...50 °C 0...80 %RH

Design and materials Case material Mounting RS232 connector RS485 connectors Dimensions Weight Protection, front/terminals

plastic desktop DB9, female RJ14, female and plug-in duplicating connector 72x150x31 mm max. 250 g IP54 / IP20

Ordered separately

Ordering code

IA100

COMECO reserves the right of changing specifications without prior notice!

(1)

Supply voltage Mains adapter (230 VAC) Consumption LEDs

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

other control instrumentation USB Interface Adapter IA250 ♦ ♦ ♦ ♦ ♦ ♦ ♦

Universal USB-to-Serial converter Optically isolated adapter Complies with USB 2.0 full speed standard Supports COMECO transmitters and RS485 devices Does not require additional power supply Suitable for "PolyMonitor" and "TraCon" software Small size and low cost

IA250 is a universal isolated interface adapter, designed to support interface connection between COMECO devices and PC or other USB devices. Its electronics is enclosed in a small-sized plastic box with IP54 front protection and equipped with USB-B and RJ25 interface connectors. Powered by the USB interface line, this plug-and-play device does not need any additional power supply. Two IA250 variants are available: - a variant for configuration and data collecting from a network of various COMECO control devices with RS485 interface and net addresses; - a variant for configuring COMECO transmitters via quasi-RS232 interface. IA250 is applicable to the "PolyMonitor" data-acquisition software and the transmitter-configuration program "TraCon", and may also be used with customer-developed PC software based on the free communication protocols of the COMECO devices.

Technical specifications 'Input' interface

Power supply

Network interface - supported net devices - function Transmitter interface - supported net devices - function Format Baud rate

RS485 up to 32 devices in up to 8 groups net control quasi RS232 COMECO smart transmitters configuration and data acquisition 8 (data) + 1 (stop), even parity max. 9600 bps

'Output' interface

5 VDC from USB line max. 100 mA

Indication 'Tx' LED 'Rx' LED

Accessories

(1)

Input cable Output cable

for data transmitting for data receiving variant 'N': K10U; variant 'T': K1U or K2U K8 (USB-B-to-USB-A standard)

Operating conditions

Interface type Function Format Speed Isolation

USB 2.0 full speed compatible connection to PC USB 2.0 specifications USB 2.0 specifications optical, 750 VAC

Software USB driver Transmitter configuration Data acquisition

FTDI standard USB driver "TraCon" v2.0 or higher, free "PolyMonitor" (1)

Operating temperature Operating humidity

0...50 °C 0...80 %RH

Design and materials Case material Mounting Input connector Output connector Dimensions Weight Protection class

plastic desktop RJ25, female USB-B, female 40x73x26 mm max. 60 g IP54

Ordered separately

Ordering code

IA250

Code Feature or option

Variant

Code values N - for RS485, T - for transmitters (quasi-RS232)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

(1)

Supply voltage Consumption

other control instrumentation Interface Adapter / Datalogger IA300 InfoPrint ♦ ♦ ♦ ♦ ♦ ♦ ♦

RS485-to-RS232 converter Data acquisition from up to 32 net devices Thermal printer control for up to 8 process graphics Data-logging functions Easy configuration with "InfoPrint" software Convenient indication Attractive price-to-resources ratio

The IA300 interface adapter InfoPrint is an intelligent device designed especially to collect data from different COMECO instruments equipped with RS485 interface and net addresses. IA300 supports up to 32 devices, connected into a RS485 net and combined in 8 groups, thermal serial printer, and RS232 communication with PC. The information collected during the data-acquisition process can be used for: - printing up to 4 process charts on-line and up to 8 charts off-line; - data logging in the adapter memory and off-line downloading to PC for further processing. The IA300 electronics is equipped with 6 LED indicators (for power and communication modes) and convenient keyboard, all mounted in a plastic enclosure with IP54 front protection. All configuration procedures (including real-time clock) can be easily programmed with the "InfoPrint Command Interface" software. With its attractive price and enhanced capabilities, the IA300 interface adapter InfoPrint is a powerful solution for building multi-point monitoring systems.

Technical specifications 'Input' interface

Indication and controls

Interface type Function Supported net devices Format Baud rate

RS485 net control and data acquisition up to 32 8 (data) + 1 (stop), even parity 4800 bps

'Output' interface Interface type Function Format Baud rate

RS232 connection to PC or serial printer 8 (data) + 1 (stop), none parity 9600 bps

Data acquisition: - max. channels - max. device groups Graphics printing: - supported printer - max. graphics Data logging: - memory capacity - data downloading Configuration software

Operating conditions 0...50 °C 0...80 %RH

Operating temperature Operating humidity

Power supply up to 32 up to 8 serial thermal printer OT801 4 (on-line), 8 (off-line) 32 Kb to PC via RS232 "InfoPrint Command Interface", free

Accessories custom made K6 (1)

RS485 input cable RS232 output cable (1)

for power ON for communication to PC/printer OK for communication to PC/printer failed for RS485 stopped or memory full for data transmitting for data receiving 2 membrane keys

9 VAC/DC included max. 110 mA

Supply voltage Mains adapter (230 VAC) Consumption

Design and materials Case material Mounting RS232 connector RS485 connectors Dimensions Weight Protection, front/terminals

plastic desktop DB9, female RJ14, female and plug-in duplicating connector 72x150x31 mm max. 250 g IP54 / IP20

Ordered separately

Ordering code

IA300 - #1.#2

Code Feature or option

Code values

Thermal printer

X - none, OT - thermal printer OT801 plus RS232 cable and 1 paper roll

Additional paper rolls

X - none, 1…10 - number of additional paper rolls

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Functions and configuration

'On' LED 'RS 232 - Comm' LED 'Fail' LED 'Stop/Full' LED 'RS 484 - Tx' LED 'RS 484 - Rx' LED Keyboard

miscellaneous Software

Code

Software

Description

OS Devices Interface

Special Cable

Interface Adapter no

Notes

"MiniSoft"

transmitter configuration and data-acquisition program

WIN MiniPAQ

RS232

yes

"RStest"

simple program for RS232 or RS485 communication test

WIN all

RS232 RS485

depending on device connected

"TraCon"

transmitter configuration and data-acquisition program

WIN TRB(I), TRY, RS232 TRZ, TRC

yes

free download from www.tracon.bz

"Ipro"

transmitter configuration and data-acquisition program

WIN TRS (IPAQ)

RS232

yes

product of INOR

"MePro"

HART Transmitter configuration and data-acquisition program

WIN MESO

HART

HART modem (communicator)

product of INOR

RS485

IA300

"InfoPrint"

configuration program for IA300 interface adapter / printer / datalogger

WIN IA300

S6 S7

"InfoMonitor"

data-acquisition program for TC800

WIN TC800

RS485

IA150

WIN LCSUPx (EchoTrack)

"EView"

viewing and configuration software for ultrasonic level transmitters w/ HART interface

HART

HART modem (communicator)

"PolyMonitor" program

universal data-acquisition

WIN all w/ RS485

RS485

IA100 IA250

S10

"UniConf"

universal configuration program

WIN all

RS232 RS485

S11

"Process"

single-process monitoring and recording program

WIN RT390

RS232

S12

"ThermLog"

temperature data-acquisition program for TC800

DOS TC800

RS485

IA150 (1)

S13

"ProfiSoft"

transmitter configuration and data-acquisition program

WIN TRP (ProfIPAQ)

RS232

yes

S14

"HartTemp"

HART Transmitter configuration and data-acquisition program

WIN TRH

HART

HART modem (communicator)

discontinued (1) product of NIVELCO

depending on device connected

product of Raycho Raykov product of INOR

Contact COMECO

COMECO reserves the right of changing specifications without prior notice!

(1)

product of INOR

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA, tel: +359 32 646524, fax: +359 32 634089, e-mail: export@comeco.org

miscellaneous Software

Code

Software

Description

OS Devices Interface

Special Cable

Interface Adapter no

Notes

"MiniSoft"

transmitter configuration and data-acquisition program

WIN MiniPAQ

RS232

yes

"RStest"

simple program for RS232 or RS485 communication test

WIN all

RS232 RS485

depending on device connected

"TraCon"

transmitter configuration and data-acquisition program

WIN TRB(I), TRY, RS232 TRZ, TRC

yes

free download from www.tracon.bz

"Ipro"

transmitter configuration and data-acquisition program

WIN TRS (IPAQ)

RS232

yes

product of INOR

"MePro"

HART Transmitter configuration and data-acquisition program

WIN MESO

HART

HART modem (communicator)

product of INOR

RS485

IA300

"InfoPrint"

configuration program for IA300 interface adapter / printer / datalogger

WIN IA300

S6 S7

"InfoMonitor"

data-acquisition program for TC800

WIN TC800

RS485

IA150

WIN LCSUPx (EchoTrack)

"EView"

viewing and configuration software for ultrasonic level transmitters w/ HART interface

HART

HART modem (communicator)

"PolyMonitor" program

universal data-acquisition

WIN all w/ RS485

RS485

IA100 IA250

S10

"UniConf"

universal configuration program

WIN all

RS232 RS485

S11

"Process"

single-process monitoring and recording program

WIN RT390

RS232

S12

"ThermLog"

temperature data-acquisition program for TC800

DOS TC800

RS485

IA150 (1)

S13

"ProfiSoft"

transmitter configuration and data-acquisition program

WIN TRP (ProfIPAQ)

RS232

yes

S14

"HartTemp"

HART Transmitter configuration and data-acquisition program

WIN TRH

HART

HART modem (communicator)

discontinued (1) product of NIVELCO

depending on device connected

product of Raycho Raykov product of INOR

Contact COMECO

COMECO reserves the right of changing specifications without prior notice!

(1)

product of INOR

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA, tel: +359 32 646524, fax: +359 32 634089, e-mail: export@comeco.org

miscellaneous Software

Code

Software

Description

OS Devices Interface

Special Cable

Interface Adapter no

Notes

"MiniSoft"

transmitter configuration and data-acquisition program

WIN MiniPAQ

RS232

yes

"RStest"

simple program for RS232 or RS485 communication test

WIN all

RS232 RS485

depending on device connected

"TraCon"

transmitter configuration and data-acquisition program

WIN TRB(I), TRY, RS232 TRZ, TRC

yes

free download from www.tracon.bz

"Ipro"

transmitter configuration and data-acquisition program

WIN TRS (IPAQ)

RS232

yes

product of INOR

"MePro"

HART Transmitter configuration and data-acquisition program

WIN MESO

HART

HART modem (communicator)

product of INOR

RS485

IA300

"InfoPrint"

configuration program for IA300 interface adapter / printer / datalogger

WIN IA300

S6 S7

"InfoMonitor"

data-acquisition program for TC800

WIN TC800

RS485

IA150

WIN LCSUPx (EchoTrack)

"EView"

viewing and configuration software for ultrasonic level transmitters w/ HART interface

HART

HART modem (communicator)

"PolyMonitor" program

universal data-acquisition

WIN all w/ RS485

RS485

IA100 IA250

S10

"UniConf"

universal configuration program

WIN all

RS232 RS485

S11

"Process"

single-process monitoring and recording program

WIN RT390

RS232

S12

"ThermLog"

temperature data-acquisition program for TC800

DOS TC800

RS485

IA150 (1)

S13

"ProfiSoft"

transmitter configuration and data-acquisition program

WIN TRP (ProfIPAQ)

RS232

yes

S14

"HartTemp"

HART Transmitter configuration and data-acquisition program

WIN TRH

HART

HART modem (communicator)

discontinued (1) product of NIVELCO

depending on device connected

product of Raycho Raykov product of INOR

Contact COMECO

COMECO reserves the right of changing specifications without prior notice!

(1)

product of INOR

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA, tel: +359 32 646524, fax: +359 32 634089, e-mail: export@comeco.org

miscellaneous Software

Code

Software

Description

OS Devices Interface

Special Cable

Interface Adapter no

Notes

"MiniSoft"

transmitter configuration and data-acquisition program

WIN MiniPAQ

RS232

yes

"RStest"

simple program for RS232 or RS485 communication test

WIN all

RS232 RS485

depending on device connected

"TraCon"

transmitter configuration and data-acquisition program

WIN TRB(I), TRY, RS232 TRZ, TRC

yes

free download from www.tracon.bz

"Ipro"

transmitter configuration and data-acquisition program

WIN TRS (IPAQ)

RS232

yes

product of INOR

"MePro"

HART Transmitter configuration and data-acquisition program

WIN MESO

HART

HART modem (communicator)

product of INOR

RS485

IA300

"InfoPrint"

configuration program for IA300 interface adapter / printer / datalogger

WIN IA300

S6 S7

"InfoMonitor"

data-acquisition program for TC800

WIN TC800

RS485

IA150

WIN LCSUPx (EchoTrack)

"EView"

viewing and configuration software for ultrasonic level transmitters w/ HART interface

HART

HART modem (communicator)

"PolyMonitor" program

universal data-acquisition

WIN all w/ RS485

RS485

IA100 IA250

S10

"UniConf"

universal configuration program

WIN all

RS232 RS485

S11

"Process"

single-process monitoring and recording program

WIN RT390

RS232

S12

"ThermLog"

temperature data-acquisition program for TC800

DOS TC800

RS485

IA150 (1)

S13

"ProfiSoft"

transmitter configuration and data-acquisition program

WIN TRP (ProfIPAQ)

RS232

yes

S14

"HartTemp"

HART Transmitter configuration and data-acquisition program

WIN TRH

HART

HART modem (communicator)

discontinued (1) product of NIVELCO

depending on device connected

product of Raycho Raykov product of INOR

Contact COMECO

COMECO reserves the right of changing specifications without prior notice!

(1)

product of INOR

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA, tel: +359 32 646524, fax: +359 32 634089, e-mail: export@comeco.org

other control instrumentation 8-channel Isolated Current Scanner ICM81 ♦ ♦ ♦ ♦ ♦ ♦ ♦

Triple isolation 8 internally powered input current loops Input current limiter Different retransmission output signals Isolated parallel interface for external control Isolated alarm outputs Self-testing and system-failure alarm

ICM81 is an 8-channel externally-controlled scanner / multiplexer of DC current signals to an isolated linear output, available in 2-wire current and 3-wire current and voltage versions. The scanner provides isolation DC power supply for all input current loops with common ground together with an automatic over-current protection and has a 3-bit isolated parallel port for external channel selection from PLC. ICM81 is equipped with sophisticated alarm circuit providing isolated alarm outputs and LED indication in case of input break and overload, output failure, and internal error. Designed for DIN-rail mounting, with its convenient plastic enclosure and detachable screw terminals, ICM81 can be very useful in industrial applications requiring DC current multiplexing with isolation, extending PLC analog input possibilities.

Technical specifications Analog inputs Number of inputs Input signal Operating range Absolute range Resolution Scanning period Input connection Input-loop power supply (ILPS) ILPS current limitation Isolation between analog inputs Isolation from main power supply

(scanned inputs) 8 DC current 0...20 mA or 4....20 mA 0...22 mA approx. 10-bit 5s 2-wire or 3-wire externally or internally (1) powered 180 mA none (common ground and supply) 1000 V

Addressing input Input configuration Logic '0' Logic '1' Consumption Input function Isolation from analog inputs

3-bit parallel port not connected connected to power supply > 12 VDC < 2 mA at logic '1' remote channel selection 2500 V

Current output - maximum load Voltage output - minimum load Resolution Output delay Output connection Isolation from analog inputs Isolation from main power supply

(3)

Measurement error Temperature drift

0.2% from span 0.01% from span for 1 °C

Power supply Supply voltage Consumption

24 VDC ± 10% max. 250 mA

Indication 'PWR' green LED 'BREAK' red LED 'OVRLD' red LED Blinking LEDs

retransmission of selected input channel 0....20 mA or 4...20 mA 750 Ω at 24V/20mA 0...10 V 1 MΩ approx. 12-bit max. 50 ms 3-wire 1000 V none (common ground)

Operating temperature Operating humidity

for device power ON for selected input channel under range for selected input channel over range for output current loop error or system failure

Case material Mounting Wiring Dimensions Weight Protection, front/terminals

Code values

Analog inputs (2)

DB - 0…20 mA, DC - 4…20 mA, Z - other (3)

G11

Analog output

E - 0…20 mA, F - 4…20 mA, K - 0…10 V, Z - other (3)

All analog inputs are of a same type! Contact COMECO

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

-10...65 °C 0...85 %RH

Design and materials

ICM81 - G6.G11

Code Feature or option

(2)

Accuracy

Provides isolated loop supply voltage - 24V/180mA for all input channels!

Ordering code

MOS gate 0.1A/60V not connected connected to common ground (0 V) input signal under- or over-range 2500 V

Operating conditions

Output function

(1)

Output type Logic '0' Logic '1' (active alarm) Outputs function Isolation from analog inputs

plastic on 35 mm DIN rail plug-in terminals 70x110x58 mm max. 150 g IP54 / IP20

COMECO reserves the right of changing specifications without prior notice!

Analog output

Alarm outputs

other control instrumentation Remote Set-point Unit TC10 ♦ ♦ ♦ ♦

Easy and convenient set-point setting via rotating dial Passive or active input channel 48x48 DIN-sized front panel Panel or rail mounting

TC10 is a self-contained unit for remote set-point setting. Replacing scrolling through controller menus with simple turning of a dial, the unit is used as accessory for programmable controllers when set point has to be changed frequently. Another TC10 application is in cases, in which there is a need to adjust the set point from a remote location – far from controller panel. Two variants are available: passive – providing resistive output signal (5 kΩ potentiometer) – and active – generating current or voltage signal proportional to set-point value. The TC10 unit is a convenient supplement to COMECO's RT controller series and other manufacturers’ automation systems.

Technical specifications Output

Power supply 0...5 kΩ 0...5 kΩ 0...max. 1 MΩ 0(4)...20 mA 0...1 V, 0...2 V, 0...5 V, or 0...10 V 0...max. 40 mA or 0...max. 10 V

Passive, resistive Passive, potentiometer Other passive (1) Active, DC current Active, DC voltage Other active (1)

Accuracy 1% from span 0.01% from span for 1 °C 0.2% per year

Setting accuracy Temperature drift Long-term stability

Indication and controls 270° arc 40 or 50, depending on the range 0…100%, 0…100 °C, 0…200 °C, 0…400 °C, 0…750 °C, 0…1000 °C, or other on request LED for active output

Dial Dial divisions Dial range (2)

LEDs (1) (2) (3)

Mains supply voltage Isolated low voltage Consumption

230 VAC or 115 VAC 12…24 V or 24 VAC max. 2 VA

Operating conditions Ambient temperature Ambient humidity

-10...65 °C 0...85 %RH

Design and materials Case material Mounting Wiring Dimensions Mounting depth Weight Protection, front/terminals

plastic in 45x45 mm panel cut-out or on 35 mm DIN rail socket OCTAL (3) 48x48(front)x95 mm max. 103 mm (w/ socket) max. 250 g IP40 / IP20

Custom; specify range within the limits stated Specify dial range when ordering. Ordered separately (see 'Accessories')

Ordering code

TC10 - G1.G11

Code Feature or option G1

Variant Power supply

Analog output

P - passive, A - active passive

X - none

active

A - 230 VAC, B - 115 VAC, Q - 12…24 V, isolated, R - 24 VAC

passive

N - resistive, P - potentiometer, Z - other (1)

active, current

E - 0...20 mA, F - 4...20 mA, Z - other (1)

active, voltage

G - 0...1 V, H - 0...2 V, I - 0...5 V, K - 0...10 V, Z - other (1)

COMECO reserves the right of changing specifications without prior notice!

G11

Code values

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

other control instrumentation Protection Unit for 3-phase AC Motors TC70 ♦ ♦ ♦ ♦ ♦ ♦

Low cost Monitors LINE (phase) presence and order Monitors phase voltage magnitude Monitors NEUTRAL (zero) presence Overheating-protection input from PTC High reliability

TC70 is a specialized device for monitoring and protection of 3-phase asynchronous motors, designed for DIN-rail mounting. It monitors phase presence and order, phase line voltage, and zero presence, and switches off its relay output in the cases of failure. An additional input for connecting a thermistor with positive temperature coefficient (posistor) is used for monitoring motor temperature. A cheap, yet highly reliable device, TC70 can be used not only for motor protection, but also in all cases, in which 3-phase system power supply should be monitored.

Technical specifications Input

Power supply

LINE control input (3-phase) NEUTRAL control input Temperature input

3 x 380 VAC ± 15% 220 VAC ± 15% PTC (RPTC at 25 °C = 1k, 2k, or other)

Output

230 VAC +10/-15% max. 4 VA

Operating conditions

Relay electromechanical Solid state relay Output function

Temperature control Indication (1)

Supply voltage Consumption

3A/250V w/ NO/NC contact 1A/250VAC switches off in situations (1): (a) missing line (R/S/T) or neutral (N), (b) line voltage exceeds 270 ± 10 V, (c) line voltage drops below 170 ± 10 V, (d) line order is not RST, STR, or TRS switches off when PTC indicates 70 °C LED for relay ON

Operating temperature Operating humidity

-10...65 °C 0...85 %RH

Design and materials Case material Mounting Wiring Dimensions Weight Protection, case/terminals

plastic on 35 mm DIN rail screw terminals 45x78x108 mm max. 300 g IP40 / IP00

Other phase voltages than the described in points (b) and (c) may be monitored if requested.

Ordering code

TC70 - G5.G6

Code Feature or option

Code values

Relay output

C - relay NO/NC, D - SSR

Temperature control input

BP - PTC 1k, BQ - PTC 2k, BZ - other PTC (specify!)

COMECO reserves the right of changing specifications without prior notice!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

other control instrumentation RPM Controller for 1-phase AC Motors SCRM ♦ ♦ ♦ ♦ ♦

AC motor power from 0.5 to 5 A / 230 VAC 0…100% speed control Automatic triac retriggering Variant with soft start Load-current sensing available

The SCRM rail-mountable RPM controller, manufactured by COMECO, is designed to control the speed of single-phase AC motors up to 5A/230VAC. The unit operates on the principle of 'phase angle control' from 25 to 180 degrees, adjusted by a front-panel thumbwheel and applied to an internal power triac. SCRM can switch up to 500 VA AC motors of fans or other industrial appliances, connected to the device output. A soft-starter variant allows the motor to reach gradually the pre-adjusted speed, while the 'loadcurrent sensing' option allows keeping the motor speed relatively constant and independent on the load. Thanks to its reliability and simplicity, the SCRM controller can be widely used in applications requiring low-cost AC-motor speed control.

Technical specifications Motor output

Power supply

Control output type Maximum motor power ratings Non rep. surge current at t = 20 ms Minimum holding current Maximum leakage current Critical rate of current rise dI/dt Critical off-state voltage rise dV/dt I2t value for fusing at t = 10 ms Fusing

phase-controlled triac 0.5...5 A / 230 VAC 50 A 50 mA 2 mA 50 A/μs 1000 V/μs 78 A2s by external fuses

Device variants

Control feedbacks Mains voltage compensation Load-current sensing (option) (2) (2)

230 VAC or 115 VAC ± 10% max. 2.5 VA

Operating conditions Operating temperature Temperature drift Operating humidity

-10...40 °C max. 0.05% for 1 °C 0...85 %RH

Indication and controls LEDs Front-panel potentiometer (2)

LED for power ON for speed set-point adjustment, 0…100%

Design and materials 25...180° phase angle 0 to max. speed for ≈ 2 s (1)

RPM controller Soft-starter

(1)

Supply voltage Consumption

≈ 1% of set-point angle per 10 V ≈ 10% of set-point angle per 1 A

Case material Mounting Wiring Dimensions Weight Protection class

plastic on 35 mm DIN rail screw terminals, 2.5 mm2 max. 35x86x58 mm max. 80 g IP40

The time depends on motor current. Only for RMP controller variant!

Ordering code

SCRM - G1 - #1

Code Feature or option

Code values 1 - RPM controller, 2 - soft-starter

Power supply

A - 230 VAC, B - 115 VAC

Load-current sensing (2)

X - none, LS - load-current compensation mounted

COMECO reserves the right of changing specifications without prior notice!

Variant

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Mounting Accessories for Electronic Devices MA Code

View

Description

Mounting

Application

MAC1

metal clamp for DIN-rail mounting

clamp

for all in-head transmitters; for devices in 40x73x26 mm box (TSR, TSOR, IA250, etc.)

MAC2

set of 2 plastic clamps for DIN-rail mounting

clamp

for devices in 80x80x60 mm box (TI200-Y, RT38-Y, TRx-D, TRU, PSF200, etc.)

clamp

MAC3

plastic clamp for DIN-rail mounting with metal holder

for all in-head transmitters; for devices in 40x73x26 mm box (TSR, TSOR, IA250, etc.); for devices in 50x45x32 mm box (RHA, TSP, TSOP, etc.)

for devices in 40x73x26 mm box (TSR, TSOR)

MAC4

plastic clamp for DIN-rail mounting

clamp

set of 4 stainless steel threaded bushes with nuts

female thread M6

for axial mounting of devices in 65x65x40 mm or 80x80x60 mm box (TI200-Y, RT38-Y, TRx-D, TRU, PSF200, RHW, etc.)

stainless steel threaded nipple with nut

male thread M12; female thread M8

for radial mounting of devices in 65x65x40 mm or 80x80x60 mm box (TI200-Y, RT38-Y, TRx-D, TRU, PSF200, RHW, etc.)

8-pin socket base (OCTAL) for DIN-rail mounting

clamp

for devices in 48x48 mm front-sized case ('S')

11-pin socket base (UNDECAL) for DIN-rail mounting

clamp

for devices in 48x48 mm front-sized case ('S') and devices in other 11-pin boxes (TRZ, RT38-R, TI08-R, etc.)

8-pin socket base (OCTAL) for DIN-rail mounting, EN50022

clamp

for devices in 48x48 mm front-sized case ('S')

MAB3

clamp

MAB4

11-pin socket base (UNDECAL) for DIN-rail mounting, EN50022; Lloyd's Register Approval

for devices in 48x48 mm front-sized case ('S') and devices in other 11-pin boxes (TRZ, RT38-R, TI08-R, etc.)

MAA1

MAR1

MAB1

MAB2

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

for all in-head transmitters

accessories Mounting Accessories for Electronic Devices MA Code

View

Description

Mounting

Application

MAC1

metal clamp for DIN-rail mounting

clamp

for all in-head transmitters; for devices in 40x73x26 mm box (TSR, TSOR, IA250, etc.)

MAC2

set of 2 plastic clamps for DIN-rail mounting

clamp

for devices in 80x80x60 mm box (TI200-Y, RT38-Y, TRx-D, TRU, PSF200, etc.)

clamp

MAC3

plastic clamp for DIN-rail mounting with metal holder

for all in-head transmitters; for devices in 40x73x26 mm box (TSR, TSOR, IA250, etc.); for devices in 50x45x32 mm box (RHA, TSP, TSOP, etc.)

for devices in 40x73x26 mm box (TSR, TSOR)

MAC4

plastic clamp for DIN-rail mounting

clamp

set of 4 stainless steel threaded bushes with nuts

female thread M6

for axial mounting of devices in 65x65x40 mm or 80x80x60 mm box (TI200-Y, RT38-Y, TRx-D, TRU, PSF200, RHW, etc.)

stainless steel threaded nipple with nut

male thread M12; female thread M8

for radial mounting of devices in 65x65x40 mm or 80x80x60 mm box (TI200-Y, RT38-Y, TRx-D, TRU, PSF200, RHW, etc.)

8-pin socket base (OCTAL) for DIN-rail mounting

clamp

for devices in 48x48 mm front-sized case ('S')

11-pin socket base (UNDECAL) for DIN-rail mounting

clamp

for devices in 48x48 mm front-sized case ('S') and devices in other 11-pin boxes (TRZ, RT38-R, TI08-R, etc.)

8-pin socket base (OCTAL) for DIN-rail mounting, EN50022

clamp

for devices in 48x48 mm front-sized case ('S')

MAB3

clamp

MAB4

11-pin socket base (UNDECAL) for DIN-rail mounting, EN50022; Lloyd's Register Approval

for devices in 48x48 mm front-sized case ('S') and devices in other 11-pin boxes (TRZ, RT38-R, TI08-R, etc.)

MAA1

MAR1

MAB1

MAB2

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

for all in-head transmitters

accessories Mounting Accessories for Electronic Devices MA Code

View

Description

Mounting

Application

MAC1

metal clamp for DIN-rail mounting

clamp

for all in-head transmitters; for devices in 40x73x26 mm box (TSR, TSOR, IA250, etc.)

MAC2

set of 2 plastic clamps for DIN-rail mounting

clamp

for devices in 80x80x60 mm box (TI200-Y, RT38-Y, TRx-D, TRU, PSF200, etc.)

clamp

MAC3

plastic clamp for DIN-rail mounting with metal holder

for all in-head transmitters; for devices in 40x73x26 mm box (TSR, TSOR, IA250, etc.); for devices in 50x45x32 mm box (RHA, TSP, TSOP, etc.)

for devices in 40x73x26 mm box (TSR, TSOR)

MAC4

plastic clamp for DIN-rail mounting

clamp

set of 4 stainless steel threaded bushes with nuts

female thread M6

for axial mounting of devices in 65x65x40 mm or 80x80x60 mm box (TI200-Y, RT38-Y, TRx-D, TRU, PSF200, RHW, etc.)

stainless steel threaded nipple with nut

male thread M12; female thread M8

for radial mounting of devices in 65x65x40 mm or 80x80x60 mm box (TI200-Y, RT38-Y, TRx-D, TRU, PSF200, RHW, etc.)

8-pin socket base (OCTAL) for DIN-rail mounting

clamp

for devices in 48x48 mm front-sized case ('S')

11-pin socket base (UNDECAL) for DIN-rail mounting

clamp

for devices in 48x48 mm front-sized case ('S') and devices in other 11-pin boxes (TRZ, RT38-R, TI08-R, etc.)

8-pin socket base (OCTAL) for DIN-rail mounting, EN50022

clamp

for devices in 48x48 mm front-sized case ('S')

MAB3

clamp

MAB4

11-pin socket base (UNDECAL) for DIN-rail mounting, EN50022; Lloyd's Register Approval

for devices in 48x48 mm front-sized case ('S') and devices in other 11-pin boxes (TRZ, RT38-R, TI08-R, etc.)

MAA1

MAR1

MAB1

MAB2

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

for all in-head transmitters

accessories Mounting Accessories for Electronic Devices MA Code

View

Description

Mounting

Application

MAC1

metal clamp for DIN-rail mounting

clamp

for all in-head transmitters; for devices in 40x73x26 mm box (TSR, TSOR, IA250, etc.)

MAC2

set of 2 plastic clamps for DIN-rail mounting

clamp

for devices in 80x80x60 mm box (TI200-Y, RT38-Y, TRx-D, TRU, PSF200, etc.)

clamp

MAC3

plastic clamp for DIN-rail mounting with metal holder

for all in-head transmitters; for devices in 40x73x26 mm box (TSR, TSOR, IA250, etc.); for devices in 50x45x32 mm box (RHA, TSP, TSOP, etc.)

for devices in 40x73x26 mm box (TSR, TSOR)

MAC4

plastic clamp for DIN-rail mounting

clamp

set of 4 stainless steel threaded bushes with nuts

female thread M6

for axial mounting of devices in 65x65x40 mm or 80x80x60 mm box (TI200-Y, RT38-Y, TRx-D, TRU, PSF200, RHW, etc.)

stainless steel threaded nipple with nut

male thread M12; female thread M8

for radial mounting of devices in 65x65x40 mm or 80x80x60 mm box (TI200-Y, RT38-Y, TRx-D, TRU, PSF200, RHW, etc.)

8-pin socket base (OCTAL) for DIN-rail mounting

clamp

for devices in 48x48 mm front-sized case ('S')

11-pin socket base (UNDECAL) for DIN-rail mounting

clamp

for devices in 48x48 mm front-sized case ('S') and devices in other 11-pin boxes (TRZ, RT38-R, TI08-R, etc.)

8-pin socket base (OCTAL) for DIN-rail mounting, EN50022

clamp

for devices in 48x48 mm front-sized case ('S')

MAB3

clamp

MAB4

11-pin socket base (UNDECAL) for DIN-rail mounting, EN50022; Lloyd's Register Approval

for devices in 48x48 mm front-sized case ('S') and devices in other 11-pin boxes (TRZ, RT38-R, TI08-R, etc.)

MAA1

MAR1

MAB1

MAB2

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

for all in-head transmitters

accessories Adjustable Mounting Flange FA DIN 43734 FLANGE Material - cast black steel (see Appendix - Sheath materials) Coating - electrostatically coated powder paint

NOMINAL SIZE

DIMENSIONS d1 (tube OD) [mm]

DN16

DN22

DN32

14...16

20...22

30...32

A [mm]

B [mm]

C [mm]

D [mm]

Fixing: 2 stainless steel screws M6x16 Maximum temperature: 300 째C Maximum pressure: atmosphere

Ordering code

FA - G4

Code Feature or option G4

Nominal size

DN16 (1), DN22, DN32 (1)

Contact COMECO!

COMECO reserves the right of changing specifications without prior notice!

(1)

Code values

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories DIN Mounting Flange FD DIN 1092-1 VARIANT *

D (FDDx)

FACE *

Material - stainless steel (see Appendix - Sheath materials) Nominal pressure - PN25...PN100

flat

raised

groove

recess

O-ring recess O-ring groove

DESIGN WITHOUT NECK (01)

DESIGN WITH WELDING NECK (11) DESIGN WITH THREADED NECK (13)

Maximum temperature: 850 °C * Other standard types and faces are available on request. Please contact COMECO!

Nominal size

DN10

DN15

DN20

DN25

DN32

DN40

DN50

DN65

18 (3/8") 90

22 (1/2") 95

27.5 (3/4") 105

34.5 (1") 115

43.5 (1¼") 140

49.5 (1½") 150

61.5 (2") 165

77.5 (2½") 185

14 / 16 60

14 / 16 65

16 / 18 75

16 / 18 85

18 100

18 110

20 125

22 145

d3 [mm]

104

h1 [mm]

d4 [mm]

102

122

d1 D [mm] b1 / b2 [mm] k [mm]

w [mm] y / z [mm] r [mm] d2 [mm] Bolts

40 / 28 4

51 / 35 4

58 / 42 4

66 / 50 6

76 / 60 6

88 / 72 6

110 / 94 6

4 x M12

4 x M16

8 x M16

FDD - G4.G5.G9.G10.G14

Code Feature or option

(1) (2)

Code values

Design

01 - w/o neck, 11 - w/ welding neck, 13 - w/ treaded neck

Nominal size

DN10, DN15, DN20, DN25, DN32, DN40, DN50, DN65, Z - other (specify!) (1)

Tube diameter (for welding) 'd1' [mm]

X - none (blind flange), 18...77.5 (2), Z - other

Connection thread 'd1'

X - none, U3 - G3/8", U4 - G1/2", U6 - G3/4", U12 - G1", U27 - G1¼", U13 - G1½", U14 - G2", Z - other (specify!) (1)

G10

Material

M1 - 1.4301, M2 - 1.4541 (1), M3 - 1.4571 (1), M9 - 1.4404 or 1.4435, Z - other (specify!) (1)

G14

Face

A - flat, B - raised, D - groove, F - recess, G - O-ring recess, H - O-ring groove

Contact COMECO! Applicable for the selected size

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Ordering code

24 35 / 23 4

accessories

SHORT-NECK VARIANT FOR TUBE WELDING Material - stainless steel (see Appendix - Sheath materials) Nominal pressure - PN40

W (FDW)

THREADED DIN 2566 VARIANT Material - stainless steel (see Appendix - Sheath materials) Nominal pressure - PN16...PN40

T (FDT)

** DIN 2633 welding neck flanges and ANSI RF flanges are also available on request. Please contact COMECO!

Nominal size

DN6

DN8

d1 thread d1 tube for welding [mm]

1/8"

1/4" 8, 10, 12

DN10

DN15

3/8" 1/2" 12, 14, 16

DN20

DN25

DN32

DN40

3/4" 1" 16, 20, 25

1¼" 1½" 25, 32, 40

DN50 2"

DN65

2½" 40, 50, 65

D [mm]

105

115

140

150

165

185

b [mm] k [mm]

12 50

12 55

14 60

14 65

16 75

16 85

16 100

16 110

18 125

18 145

d3 [mm]

105

h1 [mm]

d4 [mm]

102

122

f [mm] r [mm]

2 2

2 3

2 4

2 5

3 5

3 6

s [mm] Bolts

1.5

1.8

2.3

2.6

2.9

4 x M10

4 x M12

4 x M16

8 x M16

d2 [mm] Weight [kg]

0.38

0.54

0.61

0.91

1.10

1.60

1.78

2.43

3.18

FD - G4.G5.G9.G10

Code Feature or option G4

Code values

Variant

W - for tube welding, T - threaded DN6, DN8, DN10, DN15, DN20, DN25, DN32, DN40, DN50, DN65, Z - other (specify!) (1)

Nominal size (3)

X - none (blind flange), 8...65 (2), Z - other

Tube diameter (for welding) 'd1' [mm]

Connection thread 'd1' (2,4)

X - none, U3 - G3/8", U4 - G1/2", U6 - G3/4", U12 - G1", U27 - G1¼", U13 - G1½", U14 - G2", Z - other (specify!) (1)

G10

Material

M1 - 1.4301, M2 - 1.4541 (1), M3 - 1.4571 (1), M9 - 1.4404 or 1.4435, Z - other (specify!) (1)

(1)

Contact COMECO! Applicable for the selected size Code only for variant 'W'! (4) Code only for variant 'T'! (2)

(3)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Ordering code

11 0.33

accessories ANSI Mounting Flange FN ANSI B16.5 BLIND FLANGE

B (FNB)

Material - stainless steel (see Appendix - Sheath materials) Nominal pressure - PN25...PN100

DIMENSIONS * SIZE 1/2"

NO DRILL

3/4"

DRILLED FOR PIPE WELDING

1 ¼"

1 ½"

2 ½"

DRILLED AND THREADED

pipe OD D k G class [mm] [mm] [mm] [mm] 21.3

26.7

33.4

42.2

48.3

60.3

73.0

88.9

150 300 600 150 300 600 150 300 600 150 300 600 150 300 600 150 300 600 150 300 600 150 300 600

88.9

60.5

95.2

66.5

98.6

69.8

117.3

82.5

108

79.2

124

35.1

42.9

50.8 88.9

117.3 133.4

63.5 98.5

127 155.4

114.3

152.4

120.6

165.1

127

177.8

139.7

190.5

149.2

190.5

152.4

209.5

168.1

73.2

91.9

104.8

127

b1 RF d2 holes [mm] [mm] [mm] 9.7 12.7 14.2 11.2 14.2 15.7 12.7 16 17.5 14.2 18 20.6 16 19 22.3 17.5 20.8 25.4 20.9 23.9 28.4 22.4 26.9 31.7

1.5 6.3

15.7

1.5 6.3 1.5 6.3 1.5 6.3 1.5 6.3 1.5

19 15.7 19 15.7 19 15.7

6.3 1.5 6.3

22.3 19

6.3 1.5

22.3

weight [kg] ≈ 0.42 ≈ 0.64 ≈ 0.76 ≈ 0.61 ≈ 1.11 ≈ 1.28 ≈ 0.86 ≈ 1.39 ≈ 1.60 ≈ 1.17 ≈ 1.79 ≈ 2.23 ≈ 1.53 ≈ 2.66 ≈ 3.25 ≈ 2.42 ≈ 3.18 ≈ 4.15 ≈ 3.94 ≈ 4.85 ≈ 6.13 ≈ 4.93 ≈ 6.81 ≈ 8.44

Maximum temperature: 850 °C Maximum pressure: class 150 - 150 psig class 300 - 300 psig class 600 - 600 psig * Other standard types and dimensions are available on request. Please contact COMECO!

FNB - G4'/4".G5.G9.G10.G14

Code Feature or option

(1)

Code values

G4'

Nominal size

50 - 1/2", 75 - 3/4", 100 - 1", 125 - 1¼", 150 - 1½", 200 - 2", 250 - 2½", 300 - 3", Z - other (specify!) (1)

G4"

Nominal pressure (class)

150 - 10 bar (150 psig), 300 - 20 bar (300 psig), 600 - 40 bar (600 psig)

Pipe diameter (for welding) 'd1' [mm]

X - none (blind flange), OD (see table above)

Connection thread 'd1'

X - none, U4 - G1/2", U10 - NPT 1/2", U6 - G3/4", U11 - NPT 3/4", U12 - G1", U15 - NPT 1", U27 - G1¼", U28 - NPT 1¼", U13 - G1½", U16 - NPT 1½", U14 - G2", U17 - NPT 2", U21 - G3", U22 - NPT 3", Z - other (specify!) (1)

G10

Material

M1 - 1.4301, M2 - 1.4541 (1), M3 - 1.4571 (1), M9 - 1.4404 or 1.4435, Z - друг (поясни!) (1)

G14

Face

A - flat, B - raised

Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Ordering code

accessories Small Mounting Flange FS SMALL MOUNTING FLANGE Material - aluminum, brass, or stainless steel (see Appendix - Sheath materials) Application - with TS, LC, and RH probes

NOMINAL SIZE *

DIMENSIONS

DN5 DN6 DN8 DN9 DN10 DN12 DN14 DN16 DN18 d1 (probe OD) [mm] D [mm]

b [mm]

2 (stainless steel), 3 (brass), or 4 (aluminum)

k [mm]

d3 [mm]

h1 [mm]

no. of bolts

Fixing: stainless steel screw M4 Maximum temperature: 300 째C Maximum pressure: atmosphere * Other dimensions are available on request. Please contact COMECO!

Ordering code

FS - G4.G10

Code Feature or option Nominal size

DN5, DN6, DN8, DN9, DN10, DN12, DN14, DN16, DN18, Z - other (specify!)

G10

Material

AL - aluminum, BR - brass (Ni-plated) (1), M1 - 1.4301, M2 - 1.4541 (1), M3 - 1.4571 (1), M9 - 1.4404

Contact COMECO!

COMECO reserves the right of changing specifications without prior notice!

(1)

Code values

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Mounting Adapter YB BAYONET MOUNTING ADAPTER

YBx

DIMENSIONS *

Material - aluminum, brass, or stainless steel (see Appendix - Sheath materials) Application - with TS bayonet probes

SCREW DESIGN (1)

M10x1.5

K1 [mm]

D [mm]

H2 [mm]

Spring OD [mm]

12 (13)

14 (15)

M10x1

10 G1/8"

Bayonet Cap [mm]

10...100

1/8" NPT 10 12

M12x1.5 M10x1.5 M10x1

WRENCH DESIGN (2)

G1/8"

1/8" NPT

G1/4"

M16x1.5 19

3/8" NPT

10...100

12 (13)

15 (16)

12 / 15

15 (16) / 18 (19)

1/4" NPT G3/8"

M12x1.5 M14x1.5

12...100 15

6, 7

6, 7, 8 18 (19)

Maximum temperature: 850 °C Maximum pressure: atmosphere * Other dimensions are available on request. Please contact COMECO!

YB - G4.G6.G9'.G9".G10

Code Feature or option

(1) (2)

Code values

Design

1 - screw, 2 - wrench

Spring outer diameter 'd' [mm] (1)

6, 7, 8

Bayonet length 'H2' [mm]

10…100 (see table above)

(1)

X - none (2), Q0 - M16x1.5, Q3 - G3/8", Q7 - M12x1.5, Q8 - M14x1.5, Q9 - 3/8" NPT, Q18 - G1/8", Q19 - 1/8" NPT, Q20 - M10x1, Q23 - G1/4", Q24 - 1/4" NPT, Q30 - M10x1.5, Z - other (specify!) (2)

G9'

Connection thread 'E'

G9"

Bayonet diameter 'D' [mm] (1)

10, 12, 15, Z - other (specify!) (2)

G10

Material

AL - aluminum, BR - brass (Ni-plated) (2), M1 - 1.4301, M2 - 1.4541 (2), M3 - 1.4571 (2), M9 - 1.4404

Applicable for the selected design Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Ordering code

accessories Mounting Adapter YD THREADED MOUNTING ADAPTER

YDx

DIMENSIONS *

Material - stainless steel (see Appendix - Sheath materials) Application - with probes series TS, LC, PS, etc.

E M10x1(1.5); G1/8"

STANDARD M/M DESIGN (1)

1/8" NPT; M12x1.5 M14x1.5; G1/4" 1/4" NPT M16x1.5; G3/8" 3/8" NPT M18x1.5 M20x1.5; G1/2" 1/2" NPT M27x2; G3/4" 3/4" NPT M33x2; G1" 1" NPT M10x1(1.5); G1/8"

EXTENDED M/F DESIGN (2)

1/8" NPT; M12X1.5 M14x1.5; G1/4" 1/4" NPT M16x1.5; G3/8" 3/8" NPT M18x1.5 M20x1.5; G1/2" 1/2" NPT M27x2; G3/4" 3/4" NPT M33x2; G1" 1" NPT M16x1.5; G3/8"

LOW-PROFILE M/F DESIGN (3)

3/8" NPT M18x1.5 M20x1.5; G1/2" 1/2" NPT M27x2; G3/4" 3/4" NPT M33x2; G1" 1" NPT

SW 17 19 22 24 27 32 36 17

19 22 24 27 32 36 22 24 27 32 36

K1 [mm]

H2 [mm]

dmax [mm]

M8 / M10 / M12 G1/8" / 1/8" NPT

8 / 9 / 10 9 / 10

5/6/6 5/5

as above; M14 / G1/4" / 1/4" NPT

as above; 12 / 12 / 15

as above; 8/6/6

as above; M16 / G3/8" / 3/8" NPT

as above; 13 / 13 / 15

as above; 10 / 10 / 10

as above; M18x1.5

as above; 13

as above; 10

as above; M20 / G1/2" / 1/2" NPT

as above; 15 / 15 / 20

as above; 12

as above; M27 / G3/4" / 3/4" NPT

as above; 17 / 17 / 20

as above; 16

as above; M33 / G1" / 1" NPT

as above; 19 / 19 / 25

as above; 20

M8 / M10 / M12 / M14 G1/8"(NPT) / G1/4"(NPT)

8 / 9 / 10 / 12 8 / 11

6 / 6 / 8 / 10 6/8

as above; M16 / G3/8" / 3/8" NPT

as above; 13 / 13 / 12

as above; 12 / 12 / 12

as above; M18

as above; 14

as above; M20 / G1/2"(NPT)

as above; 15 / 15

as above; 16 / 16

as above; M27 / G3/4" / 3/4" NPT

as above; 17 / 17 / 16

as above; 20 / 20 / 20

as above; M33 / G1" / 1" NPT

as above; 19 / 19 / 18

as above; 20 / 20 / 20

M8 / M10 / M12 G1/8"(NPT) / G1/4"(NPT)

8 / 9 / 10 8 / 11

6/6/8 6/8

as above; M14

as above; 12

as above; 10

as above; M16 / G3/8" / 3/8" NPT

as above; 13 / 13 / 12

as above; 12 / 12 / 12

as above; M18 / M20 / G1/2"(NPT)

as above; 14 / 15 / 15

as above; 14 / 16 / 16

as above; M27 / G3/4" / 3/4" NPT

as above; 17 / 17 / 16

as above; 20 / 20 / 20

9 10 12 15 13

20 17 20 19 25 9 10 12 15 13 15 13 15 20 17 20 19 25 13

20 17 20 19 25

* Other dimensions are available on request. Please contact COMECO! M16x1.5; G3/8"

GLAND-TYPE DESIGN (4)

3/8" NPT M18x1.5 M20x1.5; G1/2" 1/2" NPT M27x2; G3/4" 3/4" NPT M33x2; G1" 1" NPT

22 24 27 32 36

3...8

15 13 15 20 17

N and SW1 are specified by the manufacturer

20 19 25

Maximum temperature: dependant on ferrule material Maximum pressure: 6(10) bar DN = d

* Other dimensions are available on request. Please contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

3...8 4...12 4...12 6...16 6...16 8...20

COMECO reserves the right of changing specifications without prior notice!

Maximum temperature: 850 째C Maximum pressure: 40 bar

accessories

Ordering code

YD - G4.G9'G9".G10'G10"

Code Feature or option

Code values

Design

1 - standard m/m, 2 - extended m/f, 3 - low-profile m/f, 4 - gland-type

Probe diameter 'd' [mm] (1)

1.5, 2, 3, 4, 4.5, 5, 6, 8, 10, 12, 14, 16, 20

Connection thread 'E' (1)

X - none (4), Q0 - M16x1.5, Q1 - M18x1.5, Q2 - M20x1.5, Q3 - G3/8", Q4 - G1/2", Q5 - M27x2, Q6 - G3/4", Q7 - M12x1.5, Q8 - M14x1.5, Q9 - 3/8" NPT, Q10 - 1/2" NPT, Q11 - 3/4" NPT, Q12 - G1", Q15 - 1" NPT, Q18 - G1/8", Q19 - 1/8" NPT, Q20 - M10x1, Q23 - G1/4", Q24 - 1/4" NPT, Q25 - M33x2, Q30 - M10x1.5, Z - other (specify!)

G9"

Probe thread 'N' (1,2)

X - none (4), Q0/U0 - M16x1.5, Q1/U1 - M18x1.5, Q2/U2 - M20x1.5, Q3/U3 - G3/8", Q4/U4 - G1/2", Q5/U5 - M27x2, Q6/U6 - G3/4", Q7/U7 - M12x1.5, Q8/U8 - M14x1.5, Q9/U9 - 3/8" NPT, Q10/U10 - 1/2" NPT, Q11/U11 - 3/4" NPT, Q12/U12 - G1", Q15/U15 - 1" NPT, Q18/U18 - G1/8", Q19/U19 - 1/8" NPT, Q20/U20 - M10x1, Q23/U23 - G1/4", Q24/U24 - 1/4" NPT, Q25/U25 - M33x2, Q26/U26 - M8x1, Q29/U29 - M8x1.25, Q30/U30 - M10x1.5, Z - other (specify!)

G10'

Material

G4 G9'

G10"

Compression fitting ferrule

M1 - 1.4301, M2 - 1.4541 (4), M3 - 1.4571 (4), M9 - 1.4404 or 1.4435, Z - other (specify!) (4) (3)

TF - Teflon®, BR - brass, SS - stainless steel

(1)

COMECO reserves the right of changing specifications without prior notice!

Applicable for the selected design (2) Omit for YD4! (3) Only for YD4! (4) Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Mounting Bracket YT PIPE-MOUNTING BRACKET

YTx

Material - steel or stainless steel (see Appendix - Sheath materials) Application - pipe mounting for field devices

DIMENSIONS * Design

Pipe Size

½" to 1½"

1½" to 2"

½" to 1½"

1½" to 2"

A [mm]

B [mm]

125

108

145

126

L [mm] 80 106 80 106

Tighten up: wrench size 10 Applications: - designs '1' and '2' are suitable for instrument housings with 108 mm mounting distance (e.g. EX8 or EX8W) - designs '3' and '4' are suitable for instrument housings with 126 mm mounting distance (e.g. EX10 or EX10W)

* Other dimensions are available on request. Please contact COMECO!

Ordering code

YT - G10

Code Feature or option Design

1, 2, 3, 4

G10

Material

M1 - 1.4301, M2 - 1.4541, M13 - mild (black) steel (Zn-plated (1))

Contact COMECO!

COMECO reserves the right of changing specifications without prior notice!

(1)

Code values

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Mounting Adapter YQ WELDED MOUNTING BUSH Material - stainless steel (see Appendix - Sheath materials) Application - with YP thermowells or separately

DIMENSIONS * Thermowell OD

Connection Thread M20x1.5, M27x2

≤ 17 mm

G1/2", G3/4" 1/2" NPT, 3/4" NPT M27x2, M33x2

≤ 30 mm

G3/4", G1" ¾" NPT, 1" NPT

Maximum temperature: 850 °C Maximum pressure: 63 bar

* Other dimensions are available on request. Please contact COMECO!

Ordering code

YQ - G9.G10

Code Feature or option G9

Connection thread

G10

Material

M1 - 1.4301, M2 - 1.4541 (1), M3 - 1.4571 (1), M9 - 1.4404 or 1.4435, Z - other (specify!) (1)

Contact COMECO!

COMECO reserves the right of changing specifications without prior notice!

(1)

Code values X - none, Q2 - M20x1.5, Q4 - G1/2", Q5 - M27x2, Q6 - G3/4", Q10 - 1/2" NPT, Q11 - 3/4" NPT, Q12 - G1", Q15 - 1" NPT, Q25 - M33x2, Z - other (specify!)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Protecting Accessories for Electronic Devices PA

Code

PAX1_ 0 1 2 3 PAX2_ 0 1 2 3 4 PAX3_ 0 1 2 3 4 PAX4_

Description IP65 ABS plastic box 65x65x40 mm, with mounting plate

Mounting

Application

free, wall, or rail (with clamp MAC4)

for protection of devices with maximum overall dimensions 40x40x25 mm or ø45x25 mm (e.g. low-profile in-head transmitters)

free, wall, or rail (with clamp MAC2)

for protection of devices with maximum overall dimensions 45x45x40 mm or ø50x40 mm (e.g.: in-head transmitters; devices in case type 'M')

free, wall, or rail (with clamp MAC2)

for high protection of devices with maximum overall dimensions 45x45x40 mm or ø50x40 mm (e.g.: in-head transmitters; devices in case type 'M')

free, wall, or rail (with clamp MAC2)

for Ex protection of devices with maximum overall dimensions 45x45x40 mm or ø50x40 mm

- without cable glands - with 1 plastic gland PG7 - with 2 glands PG7 at 90 ° - with 2 glands PG7 at 180 ° IP65 ABS plastic box 80x80x60 mm, with mounting plate - without cable glands - with 1 plastic gland PG7 - with 2 glands PG7 - with 2 glands PG7 at 90 ° - with 2 glands PG7 at 180 ° IP67 Aluminum box 82x77x57 mm, with mounting plate - without cable glands - with 1 metal gland PG7 - with 2 glands PG7 - with 2 glands PG7 at 90 ° - with 2 glands PG7 at 180 ° IP67 Aluminum Ex box 82x77x57 mm, with mounting plate - without cable glands - with 1 Ex gland PG7

(e.g.: in-head transmitters) Approval: Ex e II, EN 50014; IK

- with 2 glands PG7 - with 2 glands PG7 at 90 ° - with 2 glands PG7 at 180 °

COMECO reserves the right of changing specifications without prior notice!

0 1 2 3 4

View

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Explosion-proof Instrument Housing EX Variant

Specifications pressure die-cast aluminum (max. 0.5% Mg), painted with chemically resistant paint, or stainless steel grade AISI 316 (1)

Material Overall dimensions

125x105.5x94.5(height) mm

145x125.5x107(height) mm

ø90 mm / M80

ø110 mm / M100 with locking screw

Lid Conduits Cable glands

3x 1/2" NPT up to 3x ATEX brass glands for non-armored cables 6...8 mm OD (2) (option)

Sensor mounting

via central conduit

Wall mounting

2 holes ø7x108 mm

Pipe mounting

2 holes ø7x126 mm with pipe-mounting bracket (see 'Accessories')

Protection

Ex 'd' IIC; aluminum: IP68, stainless steel: IP66

Approvals Ambient temperature

ATEX 94/9/EC Ex 'd' II GD (for Zone 1/ 2/ 21/ 22) -40...100 °C

Space for transmitter

max. ø60x60 mm

Variant

max. ø85x75 mm

10W

8WD

10WD

Specifications pressure die-cast aluminum (max. 0.5% Mg), painted with chemically resistant paint, or stainless steel grade AISI 316 (1)

Material

125x105.5x109.5(height) mm ø90 mm / M80

145x125.5x127(height) mm ø110 mm / M100 with locking screw

Conduits

105x106.5x162(height) mm 2 x ø90 mm / M80

115x126.5x206(height) mm 2 x ø110 mm / M100 with locking screw

3x 1/2" NPT up to 3x ATEX brass glands for non-armored cables 6...8 mm OD (2) (option)

Cable glands Sensor mounting

via central conduit

Wall mounting

2 holes ø7x108 mm

Pipe mounting Protection

2 holes ø7x126 mm

none

with pipe-mounting bracket (see 'Accessories') Ex 'd' IIC; aluminum: IP68, stainless steel: IP66

Approvals

none

ATEX 94/9/EC Ex 'd' II GD (for Zone 1/ 2/ 21/ 22)

Ambient temperature

-40...85 °C

Space for transmitter

max. ø60x65 mm

Space for indicator

max. ø85x85 mm

max. ø60x28 mm

max. ø85x45 mm

max. ø65x50 mm

max. ø85x75 mm

(1)

Not available for dual-compartment variants! (2) Other cable glands for armored or non-armored cables are available on request.

Ordering code

EX - G10 - #1

Code Feature or option

Code values

Variant

8, 10 - closed, 8W, 10W - windowed, 8WD, 10WD - windowed, dual-compartment

G10

Material

AL - painted aluminum, SS - stainless steel 316 (1)

ATEX cable glands

X - none, CG - 1 cable gland mounted, 2CG - 2 cable glands mounted, 3CG - 3 cable glands mounted

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Overall dimensions Lid

accessories Threaded Bored Thermowell YPTB

YPTB

Material - stainless steel (see Appendix - Sheath materials) Application - with temperature gauges and TS probes STANDARD TIP

DIMENSIONS * E M20x1.5; G1/2”

SW K1

H2 [mm]

H1 [mm]

d1 [mm]

M14x1.5; G3/8”

20...100

4 / 5.5

25...100

20...100

4 / 5.5

25...100

7/9

M27x2; G3/4"

30...100

M14x1.5; G3/8”

20...100

4 / 5.5

25...100

7/9

17 / 19

M27x2; G3/4"

30...100

M33x2; G1"

35...100

M18x1.5 M20x1.5; G1/2" M14x1.5; G3/8”

M27x2; G3/4"

M33x2; G1"

1/2” NPT

3/4" NPT

1" NPT

NARROWED TIP

M20x1.5; G1/2”

M27x2; G3/4"

M33x2; G1"

Manufactured from solid HEX or round bar

1/2” NPT

3/4" NPT

L = U + K1 + H1

1" NPT

M20x1.5; G1/2"

M18x1.5

Manufactured from solid HEX or round bar L = U + K1 + H1

M18x1.5

M20x1.5; G1/2"

F1 [mm] 14

7 / 9 / 11 17 / 19 / 21

3/8” NPT

20...100

4 / 5.5

1/2" NPT

25...100

7 4 / 5.5

7/9

3/8” NPT

20...100

1/2" NPT

25...100

3/4" NPT

30...100

3/8” NPT

20...100

4 / 5.5

25...100

7/9

3/4" NPT

30...100

1" NPT

35...100

M14x1.5; G3/8”

20...100

M18x1.5

25...100

M14x1.5; G3/8”

20...100

M18x1.5

25...100

M20x1.5; G1/2"

25...100

M27x2; G3/4"

30...100

M14x1.5; G3/8”

20...100

M18x1.5

25...100

M20x1.5; G1/2"

25...100

M27x2; G3/4"

30...100

M33x2; G1"

35...100

7 / 9 / 11 16 / 18 / 20 4 / 5.5 7

7/9

20...100

4 / 5.5

25...100

7 4 / 5.5

20...100

25...100

3/4" NPT

30...100

≈ 24

7/9

≈ 30

17 / 19 17 / 19 / 21

≈ 17

13 13

≈ 23

3/8” NPT

20...100

4 / 5.5

1/2" NPT

25...100

7/9

3/4" NPT

30...100

1" NPT

35...100

≈ 27

7 / 9 / 11

Probe diameter: d ≤ d1 - 1 Probe thread: G = N Probe length (incl. thread): fixed: n = 0.98 * L - e (DIN) or 0.98 * L - e + 0.5 * H2 (NPT) spring-loaded: n ≈ L - e (DIN) or L - e + 0.5 * H2 (NPT) Maximum temperature: 850 °C Maximum pressure: 100 bar

16 / 18 / 20

INSERTION LENGTH d1 [mm]

U [mm]

max. 300

7...9

max. 500

max. 700

* Other dimensions are available on request. Please contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

17 14

7 / 9 / 11

14 14

4 / 5.5

3/8” NPT 3/8” NPT

≈ 18

4 / 5.5

1/2" NPT 1/2" NPT

= F1

1/2" NPT

M20x1.5; G1/2"

F3 [mm]

COMECO reserves the right of changing specifications without prior notice!

THREADED BORED THERMOWELL

accessories

Ordering code

YPTB - G4.G6.G7.G9'G9".G10.G14

Code Feature or option

Code values

Probe diameter 'd' [mm]

3, 4.5, 5, 6, 8, 10

Length 'U' [mm]

50…700 (see table overleaf) (1)

Length 'H1' [mm] (1)

20…100 (see table overleaf) (1)

G9'

Connection thread 'E' (1)

X - none (2), Q2 - M20x1.5, Q4 - G1/2", Q5 - M27x2, Q6 - G3/4", Q10 - 1/2" NPT, Q11 - 3/4" NPT, Q12 - G1", Q15 - 1" NPT, Q25 - M33x2, Z - other (specify!)

G9"

Probe thread 'N' (1)

X - none (2), U1 - M18x1.5, U2 - M20x1.5, U3 - G3/8", U4 - G1/2", U5 - M27x2, U6 - G3/4", U8 - M14x1.5, U9 - 3/8" NPT, U10 - 1/2" NPT, U11 - 3/4" NPT, U12 - G1", U15 - 1" NPT, U25 - M33x2, Z - other (specify!)

G10

Material

M1 - 1.4301, M2 - 1.4541 (2), M3 - 1.4571 (2), M9 - 1.4404 or 1.4435, Z - other (specify!) (2)

G14

Tip shape

X - standard closed, N - narrowed

(1)

COMECO reserves the right of changing specifications without prior notice!

Applicable for the selected probe diameter 'd' (2) Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Threaded DIN Thermowell YPTD

DIN 43772-2 THERMOWELL

YPTDx

Material - stainless steel (see Appendix - Sheath materials) Application - with temperature gauges and TS probes

DIMENSIONS * FORM

BORED DESIGNS (B6, B7, B9)

G1/2"

D1 K1 [mm] [mm] 26

H1 H2(K2) [mm] [mm]

M20x1.5; G1/2"

d1 F1(F2) [mm] [mm] 7

9 / 11

7/9 6

G3/4"

G1"

1/2" NPT

M27x2; G3/4" M20x1.5; G1/2"

22 19

17 15

3/4" NPT

1" NPT

G1/2"

≈ 21

M20x1.5; G1/2"

12 -

G3/4"

WELDED DESIGNS (W5, W8)

M20x1.5; G1/2"

9 Maximum pressure: 100 bar

G1/2"

G3/4"

9 / 11

20 / 22 17

9 / 11

≈ 25 26

19 / 20

7 7

≈ 20 27

7/9 11 / 13

M27x2; G3/4" M20x1.5; G1/2"

7/9 7

9 / 11

20 / 22

G1/2"

M20x1.5; G1/2"

G3/4"

M27x2; G3/4"

17 12

9 / 11 7/9 11 / 13

19 / 20

9 / 11

7/9 M27x2; G3/4"

7/9 11 / 13

12 / 14 14 / 16

9 / 11

7/9

12 / 14

11 / 13

14 / 16

Probe diameter: d ≤ d1 - 1 Probe thread: G = N Probe length: n = U1+18 (fixed) or n = U1+23 (spring-loaded); + 10 mm (FORM7) Maximum pressure: 25 bar (s=1.5) or 40 bar (s=2.5)

Maximum temperature: 850 °C * Other dimensions are available on request. Please contact COMECO!

YPTD - G4.G6.G9'G9".G10

Code Feature or option

Design

Code values B6 - bored, FORM 6, B7 - bored, FORM 7, B9 - bored, FORM 9, W5 - welded, FORM 5, W8 - welded, FORM 8

Probe diameter 'd' [mm]

6, 8, 10, 12

Length 'U1' [mm]

50…500 (see table above) (1)

G9'

Connection thread 'E' (2)

X - none (3), Q4 - G1/2", Q6 - G3/4", Q10 - 1/2" NPT, Q11 - 3/4" NPT, Q12 - G1", Q15 - 1" NPT, Z - other (specify!)

G9"

Probe thread 'N' (2)

X - none (3), Q2 - M20x1.5, U2 - M20x1.5, Q4 - G1/2", U4 - G1/2", Q5 - M27x2, U5 - M27x2, Q6 - G3/4", U6 - G3/4", Z - other (specify!)

G10

Material

M1 - 1.4301, M2 - 1.4541 (3), M3 - 1.4571 (3), M9 - 1.4404 or 1.4435, Z - other (specify!) (3)

(1)

Other lengths are available upon request. Contact COMECO! Applicable for the selected probe diameter (3) Contact COMECO! (2)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Ordering code

accessories Threaded Gland-type Thermowell YPTG GLAND-TYPE THERMOWELL

YPTGx

Sheath - stainless steel (see Appendix - Sheath materials) Ferrule - stainless steel, brass, or Teflon®

DIMENSIONS * E

D1 K1 SW [mm] [mm]

M20x1.5; G1/2"

BORED DESIGN (B)

d1 [mm]

F1 [mm]

SW1

≈ 20

4/5/6/7/9

G1/4"

≈ 21

11 / 13

G3/8"

≈ 25

6, 7, 8, 9

8, 10, 12

G1/4"

6, 7, 8, 9, 10 11

8, 10, 12 14

G1/4" G3/8"

13 17

6, 7, 8, 9, 10 11, 12, 13

8, 10, 12 14, 16

G1/4" G3/8"

13 17

6, 7, 8, 9, 10 11, 12, 13, 16

8, 10, 12, 14, 16, 20

G1/4" G3/8"

13 17

27 1/2" NPT M27x2; G3/4" 32 3/4" NPT M33x2; G1" Maximum pressure: 100 bar

36 1" NPT

Manufactured from solid HEX or round bar

M16x1.5; G3/8"

WELDED DESIGN (W)

3/8" NPT M18x1.5 M20x1.5; G1/2" 1/2" NPT M27x2; G3/4" 3/4" NPT M33x2; G1" 1" NPT

Maximum pressure: 25 bar

22 24 27 32 36

≈ 20

≈ 21

≈ 25

Probe diameter: d = DN ≤ d1 - 1 Free probe length: n ≥ U1+30 Maximum temperature: dependant on ferrule material * Other dimensions are available on request. Please contact COMECO!

YPTG - G4.G6.G9'G9".G10

Code Feature or option

(1) (2)

Code values

Design

B - bored, W - welded

Probe diameter 'd' [mm]

3, 4, 4.5, 5, 6, 8, 10, 12

Length 'U1' [mm]

30…500 (see table above)

G9'

Connection thread 'E' (1)

X - none (2), Q0 - M16x1.5, Q1 - M18x1.5, Q2 - M20x1.5, Q3 - G3/8", Q4 - G1/2", Q5 - M27x2, Q6 - G3/4", Q9 - 3/8" NPT, Q10 - 1/2" NPT, Q11 - 3/4" NPT, Q12 - G1", Q15 - 1" NPT, Q25 - M33x2, Z - other (specify!)

G9"

Compression fitting ferrule

TF - Teflon® (up to 200 °C), BR - brass (up to 400 °C), SS - stainless steel (up to 800 °C)

G10

Sheath material

M1 - 1.4301, M2 - 1.4541 (2), M3 - 1.4571 (2), M9 - 1.4404 or 1.4435, Z - other (specify!) (2)

Applicable for the selected probe diameter Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Ordering code

accessories Threaded Thermowell with Fixing Screw YPTS THERMOWELL WITH FIXING SCREW

YPTSx

Sheath - stainless steel (see Appendix - Sheath materials) Application - with temperature gauges and TS probes

DIMENSIONS * FORM

BORED DESIGN (B)

N D1 K1 SW [mm] [mm] [mm]

M20x1.5; G1/2" 1

≈ 20

d1 [mm]

7 / 9 / 11 M20x1.5; G1/2" 2 ***

M16x1.5; G3/8"

WELDED DESIGN (W)

≈ 20

3/8" NPT 1 **

M18x1.5

M20x1.5; G1/2"

14.5 ****

1/2" NPT M16x1.5; G3/8"

≈ 20 13

3/8" NPT 2 *** Maximum probe length: n = U1+4 Maximum pressure: 25 bar

6 / 8 / 9(10)

5/6/8

8 / 10 / 12

6/8 9(10) / 11

5/6 8 / 10

8 / 10 12 / 14

6 / 8 / 9(10)

5/6/8

8 / 10 / 12

6/8 9(10) / 11

5/6 8 / 10

8 / 10 12 / 14

15 d1

M18x1.5 M20x1.5; G1/2"

6 / 8 / 10 13 / 15 / 17

1/2" NPT

Manufactured from solid HEX or round bar

F1 [mm]

14.5 ****

1/2" NPT

Maximum probe length: n = U1-2 Maximum pressure: 100 bar

d [mm]

1/2" NPT

13 15 ≈ 20

Free probe length: n ≥ U1+13 Fixing screw: M4, stainless steel Maximum temperature: 450 °C * Other dimensions are available on request. Please contact COMECO! ** for temperature gauges *** for TS probes **** gauge neck + 0.5 mm

YPTS - G4.G6.G9.G10

Code Feature or option

(1) (2)

Design

Code values B1 - bored, FORM1, B2 - bored, FORM2, W1 - welded, FORM1, W2 - welded, FORM2

Probe diameter 'd' [mm]

5, 6, 8, 10

Length 'U1' [mm]

30…300 (see table above)

Connection thread 'E' (1)

X - none (2), Q0 - M16x1.5, Q1 - M18x1.5, Q2 - M20x1.5, Q3 - G3/8", Q4 - G1/2", Q9 - 3/8" NPT, Q10 - 1/2" NPT, Z - other (specify!)

G10

Material

M1 - 1.4301, M2 - 1.4541 (2), M3 - 1.4571 (2), M9 - 1.4404 or 1.4435, Z - other (specify!) (2)

Applicable for the selected probe diameter Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Ordering code

accessories Threaded Tapered Thermowell YPTT THREADED TAPERED THERMOWELL

YPTT

Material - stainless steel (see Appendix - Sheath materials) Application - with temperature gauges and TS probes

DIMENSIONS * E M20x1.5; G1/2”

SW K1 27

H2 [mm]

H1 [mm]

d1 [mm]

M14x1.5; G3/8”

20...100

4 / 5.5

25...100

20...100

4 / 5.5

25...100

7/9

M18x1.5 M20x1.5; G1/2" M14x1.5; G3/8”

M27x2; G3/4"

M33x2; G1"

Manufactured from solid HEX or round bar

M20x1.5; G1/2"

3/4" NPT

L = U + K1 + H1

F1 [mm]

≈ 18

≈ 24

M27x2; G3/4"

30...100

M14x1.5; G3/8”

20...100

4 / 5.5

25...100

7/9

17 / 19

M27x2; G3/4"

30...100

M33x2; G1"

35...100

M18x1.5

1/2” NPT

1" NPT

M18x1.5

F3 [mm]

M20x1.5; G1/2"

7 / 9 / 11 17 / 19 / 21

3/8” NPT

20...100

4 / 5.5

1/2" NPT

25...100

7 4 / 5.5

7/9

3/8” NPT

20...100

1/2" NPT

25...100

3/4" NPT

30...100

3/8” NPT

20...100

4 / 5.5

1/2" NPT

25...100

7/9

3/4" NPT

30...100

1" NPT

35...100

≈ 30

≈ 17

≈ 23

≈ 27

7 / 9 / 11 16 / 18 / 20

INSERTION LENGTH d1 [mm]

U [mm]

max. 300

7...9

max. 500

max. 700

* Other dimensions are available on request. Please contact COMECO!

YPTT - G4.G6.G7.G9'G9".G10

Code Feature or option

(1) (2)

Code values

Probe diameter 'd' [mm]

3, 4.5, 5, 6, 8, 10

Length 'U' [mm]

50…700 (see table above) (1) (1)

20…100 (see table above) (1)

Length 'H1' [mm]

G9'

Connection thread 'E' (1)

X - none (2), Q2 - M20x1.5, Q4 - G1/2", Q5 - M27x2, Q6 - G3/4", Q10 - 1/2" NPT, Q11 - 3/4" NPT, Q12 - G1", Q15 - 1" NPT, Q25 - M33x2, Z - other (specify!)

G9"

Probe thread 'N' (1)

G10

Material

M1 - 1.4301, M2 - 1.4541 (2), M3 - 1.4571 (2), M9 - 1.4404 or 1.4435, Z - other (specify!) (2)

Applicable for the selected probe diameter 'd' Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Ordering code

accessories Threaded Welded Thermowell YPTW YPTW

Material - stainless steel (see Appendix - Sheath materials) Application - with temperature gauges and TS probes STANDARD TIP

DIMENSIONS * E M20x1.5; G1/2”

M27x2; G3/4"

M33x2; G1"

SW K1

1/2” NPT

3/4" NPT

Manufactured from solid HEX or round bar U = 50...1500 mm L = U + K1 + H1 S = 1...3 mm 1" NPT

NARROWED TIP

M20x1.5; G1/2”

M27x2; G3/4"

M33x2; G1"

1/2” NPT

3/4" NPT

Manufactured from solid HEX or round bar U = 50...1500 mm L = U + K1 + H1 S = 1...3 mm S1 = 1...2 mm

1" NPT

H2 [mm]

H1 [mm]

M14x1.5; G3/8”

20...100

M18x1.5

25...100

M20x1.5; G1/2"

25...100

M14x1.5; G3/8”

20...100

M18x1.5

25...100

M20x1.5; G1/2"

25...100

M27x2; G3/4"

30...100

M14x1.5; G3/8”

20...100

M18x1.5

25...100

M20x1.5; G1/2"

25...100

M27x2; G3/4"

30...100

M33x2; G1"

35...100

3/8” NPT

20...100

1/2" NPT

25...100

3/8” NPT

20...100

1/2" NPT

25...100

3/4" NPT

30...100

3/8” NPT

20...100

1/2" NPT

25...100

3/4" NPT

30...100

1" NPT

35...100

M14x1.5; G3/8”

20...100

M18x1.5

25...100

M20x1.5; G1/2"

25...100

M14x1.5; G3/8”

20...100

M18x1.5

25...100

M20x1.5; G1/2"

25...100 30...100

M27x2; G3/4"

M14x1.5; G3/8”

20...100

M18x1.5

25...100

M20x1.5; G1/2"

25...100

M27x2; G3/4"

30...100

M33x2; G1"

35...100

3/8” NPT

20...100

1/2" NPT

25...100

3/8” NPT

20...100

1/2" NPT

25...100

3/4" NPT

30...100

3/8” NPT

20...100

1/2" NPT

25...100

3/4" NPT

30...100

1" NPT

35...100

Probe diameter: d ≤ (F3 - 2*S) - 1 Probe thread: G = N Probe length (incl. thread): fixed: n = 0.98 * L - e (DIN) or 0.98*L - e + 0.5*H2 (NPT) spring-loaded: n ≈ L - e (DIN) or L - e + 0.5*H2 (NPT) Maximum temperature: 850 °C

F1 [mm] 10, 12, 14, 1/8", 1/4"

10, 12, 14, 16, 18, 1/8", 1/4", 3/8"

10, 12, 14, 16, 18, 20, 1/8", 1/4", 3/8", 1/2"

= F1

10, 12, 14, 1/8", 1/4" 10, 12, 14, 16, 18, 1/8", 1/4", 3/8" 10, 12, 14, 16, 18, 20, 1/8", 1/4", 3/8", 1/2" 10, 12, 14, 1/8", 1/4"

8, 10

10, 12, 14, 16, 18, 1/8", 1/4", 3/8"

8, 10, 12

10, 12, 14, 16, 18, 20, 1/8", 1/4", 3/8", 1/2"

8, 10, 12, 14

10, 12, 14, 1/8", 1/4"

8, 10

10, 12, 14, 16, 18, 1/8", 1/4", 3/8"

8, 10, 12

10, 12, 14, 16, 18, 20, 1/8", 1/4", 3/8", 1/2"

8, 10, 12, 14

MAXIMUM PRESSURE S(S1) [mm]

P [bar]

1.5 (2)

2.5 (3)

* Other dimensions are available on request. Please contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

F3 [mm]

COMECO reserves the right of changing specifications without prior notice!

THREADED WELDED THERMOWELL

accessories

Ordering code

YPTW - G4.G6.G7.G9'G9".G10.G14

Code Feature or option

Code values 10, 12, 14, 16, 18, 20, 1/8" (2), 1/4" (2), 3/8" (2), 1/2" (2)

Tube diameter 'F1' [mm]

Length 'U' [mm]

50…1500 (see table overleaf)

Length 'H1' [mm] (1)

20…100 (see table overleaf) (1)

G9'

Connection thread 'E' (1)

X - none (2), Q2 - M20x1.5, Q4 - G1/2", Q5 - M27x2, Q6 - G3/4", Q10 - 1/2" NPT, Q11 - 3/4" NPT, Q12 - G1", Q15 - 1" NPT, Q25 - M33x2, Z - other (specify!)

G9"

Probe thread 'N' (1)

G10

Material

M1 - 1.4301, M2 - 1.4541 (2), M3 - 1.4571 (2), M9 - 1.4404 or 1.4435, Z - other (specify!) (2)

G14

Tip shape

X - standard closed, N - narrowed

(1)

COMECO reserves the right of changing specifications without prior notice!

Applicable for the selected tube diameter 'F1' (2) Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Weldable DIN Thermowell YPWD DIN 43772-2 THERMOWELL

YPWD

DIMENSIONS * N

F2 [mm]

M14x1.5

4 / 5.5

M18x1.5

12.5

Sheath - stainless steel (see Appendix - Sheath materials) Application - with temperature gauges and TS probes

F3 [mm]

d1 [mm]

H1 H2 [mm] [mm] 16

L [mm]

U [mm]

M20x1.5 G1/2"

12.5 / 15

7/9

M27x2 G3/4"

15 / 17 / 19

9 / 11 / 13

110 / 140

170 / 200

125

260 / 410

125 / 275

Probe diameter: d = d1 - 1 Probe thread: G = N Probe length: n = 0.98 * L - 5 (fixed) or n ≈ L - 5 (spring-loaded) Maximum temperature: 850 °C Maximum pressure: 160(250*) bar * Other dimensions are available on request. Please contact COMECO!

DIN 43763 THERMOWELL

YPWDx

Sheath - stainless steel (see Appendix - Sheath materials) Application - with TS probes with M18x1.5 external thread

DIMENSIONS * FORM

L [mm]

U [mm]

140

2 3

200

125 65

4 5

260

255

125

F2 [mm]

F3 [mm]

d1 [mm]

b [mm]

12.5

3.5

12.5

3.5

Probe diameter: d = d1 - 1 Probe thread: G = M18x1.5 Probe length: n = 0.98 * L - b (fixed) or n ≈ L - b (spring-loaded) Maximum temperature: 850 °C Maximum pressure: 250(500*) bar * Other dimensions are available on request. Please contact COMECO!

YPW - G4.G6.G9.G10

Code Feature or option Variant

Probe diameter 'd' [mm]

3, 4.5, 6, 8, 10, 12

Length 'L' [mm]

110…410 (see table above) (1)

Probe thread 'N' (2)

X - none (3), U1 - M18x1.5, U2 - M20x1.5, U4 - G1/2", U5 - M27x2, U6 - G3/4", U8 - M14x1.5, Z - other (specify!)

G10

Material

M1 - 1.4301, M2 - 1.4541, M3 - 1.4571 (3), M9 - 1.4404 or 1.4435, Z - other (specify!) (3)

(1) (2) (3)

Code values D - DIN 43772-2, D1 - DIN 43763, FORM1, D2 - DIN 43763, FORM2, D3 - DIN 43763, FORM3, D4 - DIN 43763, FORM4, D5 - DIN 43763, FORM5, D6 - DIN 43763, FORM6

Other lengths are available upon request. Contact COMECO! Applicable for the selected probe diameter Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Ordering code

accessories Weldable Gland-type Thermowell YPWG GLAND-TYPE THERMOWELL

DIMENSIONS *

Sheath - stainless steel (see Appendix - Sheath materials) Ferrule - stainless steel, brass, or Teflon®

U1 [mm]

L [mm]

110

100

130

d1 [mm]

DN(d) [mm]

F1 [mm]

D1 [mm]

4/5/6/7/9

3/4/5/6/8

8 / 9 / 10 / 11 / 13

G1/4"

Probe diameter: d ≤ d1 - 1 Free probe length: n ≥ U1+45 Maximum temperature: dependant on ferrule material Maximum pressure: up to 100 bar (depending on welding technology) * Other dimensions are available on request. Please contact COMECO!

Ordering code

YPWG - G4.G6.G9.G10

Code Feature or option

(2)

Probe diameter 'd' [mm]

3, 4, 4.5, 5, 6, 8, 10

Length 'U1' [mm]

15…100 (see table above) (1)

Compression fitting ferrule

TF - Teflon® (up to 200 °C), BR - brass (up to 400 °C), SS - stainless steel (up to 800 °C)

G10

Sheath material

M1 - 1.4301, M2 - 1.4541 (2), M3 - 1.4571 (2), M9 - 1.4404 or 1.4435, Z - other (specify!) (2)

Other lengths are available upon request. Contact COMECO! Contact COMECO!

COMECO reserves the right of changing specifications without prior notice!

(1)

Code values

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Weldable Thermowell with Fixing Screw YPWS THERMOWELL WITH FIXING SCREW

DIMENSIONS *

Sheath - stainless steel (see Appendix - Sheath materials) Application - with temperature gauges and TS probes

U1 [mm]

L [mm]

110

100

130

FORM

N [mm]

D1 [mm]

d1 [mm]

d [mm]

F1 [mm]

1 **

14.5 ****

7 / 9 / 11

6 / 8 / 10

11 / 13 / 15

2 ***

6/7/9

5/6/8

10 / 11 / 13

Probe diameter: d ≤ d1 - 1 Maximum probe length: n = U1+5 Free probe length: n ≥ U1+45 Fixing screw: M4, stainless steel Maximum temperature: 450 °C Maximum pressure: up to 100 bar (depending on welding technology) * Other dimensions are available on request. Please contact COMECO! ** for temperature gauges *** for TS probes **** gauge neck + 0.5 mm

Ordering code

YPWS - G4.G6.G10

Code Feature or option

(2)

1 - FORM1, 2 - FORM2

Probe diameter 'd' [mm]

3, 4, 4.5, 5, 6, 8, 10

Length 'U1' [mm]

15…100 (see table above) (1)

G10

Material

M1 - 1.4301, M2 - 1.4541 (2), M3 - 1.4571 (2), M9 - 1.4404 or 1.4435, Z - other (specify!) (2)

Other lengths are available upon request. Contact COMECO! Contact COMECO!

COMECO reserves the right of changing specifications without prior notice!

(1)

Code values

Form

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Flanged Bored Thermowell YPFB DIN-FLANGED BORED THERMOWELL

YPFBD

DIMENSIONS * N

H2 [mm]

M14x1.5, G3/8”

4 / 5.5

13 / 15

≈ 18

M18x1.5

≈ 24

M20x1.5, G1/2"

7/9

17 / 19

≈ 26

M27x2, G3/4"

7 / 9 / 11

17 / 19 / 21

≈ 31

Material - stainless steel (see Appendix - Sheath materials) Application - with temperature gauges and TS probes

H1 [mm]

F2 [mm]

d1 [mm]

F3 [mm]

F1 [mm]

INSERTION LENGTH

Probe diameter: d = d1 - 1 Probe thread: G = N Probe length (incl. thread): n = 0.98 * L - e (fixed) or n ≈ L - e (spring-loaded) Maximum temperature: 850 °C Maximum pressure: 40 bar

d1 [mm]

U [mm]

max. 300

7...9

max. 500

max. 700

FLANGE DIMENSIONS * NOMINAL SIZE

D [mm]

DN10 DN15 DN20 DN25 DN32 DN40 DN50

L = U + b + H1 (flat face) or L = U + b + H1 + 2 (raised face)

90 95 105 115 140 150 165

k [mm] 60 65 75 85 100 110 125

b d2 [mm] [mm]

bolts

14 14

4 x M12

16 18

Flange type: DIN 2527 or EN DIN 1092-1 Maximum pressure: PN40

4 x M16

* Other dimensions are available on request. Please contact COMECO!

Ordering code

YPFBD - G4.G6.G8.G9.G10.G14

Code Feature or option

Code values

Probe diameter 'd' [mm]

3, 4.5, 5, 6, 8, 10

Length 'U' [mm]

50…700 (see table above) (1)

Flange nominal size

DN10 (2), DN15, DN20, DN25, DN32, DN40, DN50, Z - other (specify!) (2)

Probe thread 'N' (1)

Q1 - M18x1.5, Q2 - M20x1.5, Q3 - G3/8", Q4 - G1/2", Q5 - M27x2, Q6 - G3/4", Q8 - M14x1.5, Z - other (specify!) (2)

G10

Material

M1 - 1.4301, M2 - 1.4541, M3 - 1.4571 (2), M9 - 1.4404 or 1.4435, Z - other (specify!) (2)

G14

Flange face

A - flat (FF), B - raised (RF), D - groove, F - recess, G - O-ring recess, H - O-ring groove

(1)

COMECO reserves the right of changing specifications without prior notice!

Applicable for the selected probe diameter 'd' (2) Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories

ANSI-FLANGED BORED THERMOWELL

YPFBA

DIMENSIONS *

Material - stainless steel (see Appendix - Sheath materials) Application - with temperature gauges and TS probes

H2 [mm]

H1 [mm]

F2 [mm]

d1 [mm]

F3 [mm]

F1 [mm]

3/8” NPT

4 / 5.5

13 / 15

≈ 24

1/2" NPT

7/9

17 / 19

≈ 28

3/4" NPT

7 / 9 / 11

17 / 19 / 21

≈ 31

INSERTION LENGTH

Probe diameter: d = d1 - 1 Probe thread: G = N Probe length (incl. thread): n = 0.98 * L - e + 0.4 * H2 (fixed) or n ≈ L - e + 0.4 * H2 (spring-loaded) Maximum temperature: 850 °C Maximum pressure: 40 bar

d1 [mm]

U [mm]

max. 300

7...9

max. 500

max. 700

FLANGE DIMENSIONS [mm] * SIZE class 1/2"

3/4"

1 ¼" L = U + b + H1 (flat face) or L = U + RF + b + H1 (raised face)

1 ½"

150 300 600 150 300 600 150 300 600 150 300 600 150 300 600 150 300 600

88.9

60.5

95.2

66.5

98.6

69.8

9.7 12.7 14.2 11.2 14.2 15.7 12.7 16 17.5 14.2 18 20.6 16 19 22.3 17.5 20.8 25.4

117.3

82.5

108

79.2

124

88.9

117.3 133.4

98.6

127 155.4 114.3 152.4 120.6 165.1

127

holes

1.5 6.3

15.7 Flange type:

1.5 6.3 1.5 6.3 1.5 6.3 1.5 6.3 1.5

15.7

Maximum pressure:

class 150 - 150 psig class 300 - 300 psig class 600 - 600 psig

15.7 19 15.7

ANSI B16.5

(to fit thermowell specifications)

22.3 19

6.3

* Other dimensions are available on request. Please contact COMECO!

YPFBA - G4.G6.G8'/8".G9.G10.G14

Code Feature or option

Code values

Probe diameter 'd' [mm]

3, 4.5, 5, 6, 8, 10

Length 'U' [mm]

50…700 (see table above) (1)

G8'

Flange nominal size

50 - 1/2", 75 - 3/4", 100 - 1", 125 - 1¼", 150 - 1½", 200 - 2", Z - other (specify!) (2)

G8"

Flange nominal pressure (class)

150 - 10 bar (150 psig), 300 - 20 bar (300 psig), 600 - 40 bar (600 psig)

(1)

Q9 - 3/8" NPT, Q10 - 1/2" NPT, Q11 - 3/4" NPT, Z - other (specify!) (2)

Probe thread 'N'

G10

Material

M1 - 1.4301, M2 - 1.4541, M3 - 1.4571 (2), M9 - 1.4404 or 1.4435, Z - other (specify!) (2)

G14

Flange face

A - flat (FF), B - raised (RF), D - groove, F - recess, G - O-ring recess, H - O-ring groove

(1)

Applicable for the selected probe diameter 'd' (2) Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Ordering code

accessories Flanged Bored Step-Tip Thermowell YPFN DIN-FLANGED BORED STEP-TIP THERMOWELL

YPFND

Material - stainless steel (see Appendix - Sheath materials) Application - with temperature gauges and TS probes

DIMENSIONS * N

H2 [mm]

H1 [mm]

F2 [mm]

d1 [mm]

F1 [mm]

F3 [mm]

M14x1.5, G3/8”

20 + T

4 / 5.5

≈ 18

13...16

M18x1.5

25 + T

≈ 24

15...21

M20x1.5, G1/2"

25 + T

7/9

≈ 26

15 / 17...21

M27x2, G3/4"

30 + T

7 / 9 / 11

≈ 26 / 30 15 / 17 / 21...25

INSERTION LENGTH

Probe diameter: d = d1 - 1 Probe thread: G = N Probe length (incl. thread): n = 0.98 * L - e (fixed) or n ≈ L - e + 1 (spring-loaded) Maximum temperature: 850 °C Maximum pressure: 40 bar

d1 [mm]

U [mm]

max. 300

7...9

max. 700

max. 1000

FLANGE DIMENSIONS * NOMINAL D k b d2 SIZE [mm] [mm] [mm] [mm]

L = U + b + H1 (flat face) or L = U + b + H1 + 2 (raised face) Fillet radius at root and step 1...3 mm Full penetration weld design is also available on request

DN10 DN15 DN20 DN25 DN32 DN40 DN50

90 95 105 115 140 150 165

60 65 75 85 100 110 125

bolts

DIN 2527 or EN DIN 1092-1

14 14

4 x M12

16 18

Flange type:

Maximum pressure: PN40 18

4 x M16

* Other dimensions are available on request. Please contact COMECO!

Ordering code

YPFND - G4.G5.G6.G7.G8.G9.G10.G14

Code Feature or option

Code values

Probe diameter 'd' [mm]

3, 4.5, 5, 6, 8, 10

Insertion diameter 'F1' [mm]

13…21 (see table above) (1)

Shank length 'U' [mm]

50…1000 (2) (see table above) (1)

Extension length 'T' [mm]

0…100

Flange nominal size

DN10 (2), DN15, DN20, DN25, DN32, DN40, DN50, Z - other (specify!) (2)

Probe thread 'N' (1)

U1 - M18x1.5, U2 - M20x1.5, U3 - G3/8", U4 - G1/2", U5 - M27x2, U6 - G3/4", U8 - M14x1.5, Z - other (specify!) (2)

G10

Material

M1 - 1.4301, M2 - 1.4541, M3 - 1.4571 (2), M9 - 1.4404 or 1.4435, Z - other (specify!) (2)

G14

Flange face

A - flat (FF), B - raised (RF), D - groove, F - recess, G - O-ring recess, H - O-ring groove

Applicable for the selected probe diameter 'd' (2) Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

(1)

accessories

ANSI-FLANGED BORED STEP-TIP THERMOWELL

DIMENSIONS *

YPFNA N

H2 [mm]

H1 [mm]

F2 [mm]

d1 [mm]

F1 [mm]

F3 [mm]

3/8” NPT

25 + T

4 / 5.5

≈ 24

13...21

1/2" NPT

30 + T

7/9

≈ 27

15 / 17...23

3/4" NPT

35 + T

7 / 9 / 11

≈ 26 / 30

15 / 17 / 21...25

Material - stainless steel (see Appendix - Sheath materials) Application - with temperature gauges and TS probes

INSERTION LENGTH

Probe diameter: d = d1 - 1 Probe thread: G = N Probe length (incl. thread): n = 0.98 * L - e (fixed) or n ≈ L (spring-loaded) Maximum temperature: 850 °C Maximum pressure: 100 bar

d1 [mm]

U [mm]

max. 300

7...9

max. 700

max. 1000

FLANGE DIMENSIONS [mm] * SIZE class 1/2"

3/4"

1 ¼" L = U + b + H1 (flat face) or L = U + RF + b + H1 (raised face) 1 ½"

Fillet radius at root and step 1...3 mm Full penetration weld design is also available on request

150 300 600 900 150 300 600 900 150 300 600 900 150 300 600 900 150 300 600 900 150 300 600 900

88.9

60.5

95.2

66.5

9.7 12.7 14.2 22.3 11.2 14.2 15.7 25.4 12.7 16 17.5 28.4 14.2 18 20.6 28.4 16 19 22.3 31.7 17.5 20.8 25.4 38.1

120.6 98.6

82.5 69.8

117.3

82.5

130 108

88.9 79.2

124

88.9

149.3 101.6 117.3 88.9 133.4

98.6

158.7 111.2 127 98.6 155.4 114.3 177.8 123.9 152.4 120.6 165.1

127

215.9 165.1

RF 1.5 6.3 1.5

holes

15.7

1.5

ANSI B16.5

22.3 15.7 19

6.3

Flange type:

19 6.3 1.5

25.4 15.7

(to fit thermowell specifications)

19 6.3 1.5

25.4 15.7

22.3 6.3 1.5 6.3

Maximum pressure: class 150 - 150 psig class 300 - 300 psig class 600 - 600 psig class 900 - 900 psig class 1500 - 1500 psig

22.3 15.7

Dimensions for classes 900 and 1500 are identical up to 2 ½" size!

28.4 19 8 25.4

* Other dimensions are available on request. Please contact COMECO!

YPFNA - G4.G5.G6.G7.G8'/8".G9.G10.G14

Code Feature or option

(1) (2)

Code values

Probe diameter 'd' [mm]

3, 4.5, 5, 6, 8, 10

Insertion diameter 'F1' [mm]

13…21 (see table above) (1)

Shank length 'U' [mm]

50…1000 (2) (see table above) (1)

Extension length 'T' [mm]

0…100

G8'

Flange nominal size

50 - 1/2", 75 - 3/4", 100 - 1", 125 - 1¼", 150 - 1½", 200 - 2", Z - other (specify!) (2)

G8"

Flange nominal pressure (class)

150 - 10 bar (150 psig), 300 - 20 bar (300 psig), 600 - 40 bar (600 psig), 900 - 60 bar (900 psig), 1500 - 100 bar (1500 psig)

Probe thread 'N' (1)

U9 - 3/8" NPT, U10 - 1/2" NPT, U11 - 3/4" NPT, Z - other (specify!) (2)

G10

Material

M1 - 1.4301, M2 - 1.4541, M3 - 1.4571 (2), M9 - 1.4404 or 1.4435, Z - other (specify!) (2)

G14

Flange face

A - flat (FF), B - raised (RF), D - groove, F - recess, G - O-ring recess, H - O-ring groove

Applicable for the selected probe diameter 'd' Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Ordering code

accessories Flanged Bored Straight Thermowell YPFS DIN-FLANGED BORED STRAIGHT THERMOWELL

YPFSD

Material - stainless steel (see Appendix - Sheath materials) Application - with temperature gauges and TS probes

DIMENSIONS * H2 [mm]

H1 [mm]

F2 [mm]

d1 [mm]

F1 [mm]

M14x1.5, G3/8”

20 + T

4 / 5.5

13…19

M18x1.5

25 + T

15…21

M20x1.5, G1/2"

25 + T

7/9

15…21 / 17…21

M27x2, G3/4"

30 + T

7 / 9 / 11

15…21 / 17…21 / 21

INSERTION LENGTH

Probe diameter: d = d1 - 1 Probe thread: G = N Probe length (incl. thread): n = 0.98 * L - e (fixed) or n ≈ L - e + 1 (spring-loaded) Maximum temperature: 850 °C Maximum pressure: 40 bar

d1 [mm]

U [mm]

max. 300

7...9

max. 700

max. 1000

FLANGE DIMENSIONS * NOMINAL D k b d2 SIZE [mm] [mm] [mm] [mm]

L = U + b + H1 (flat face) or L = U + b + H1 + 2 (raised face) Fillet radius at root 1..3 mm Full penetration weld design is also available on request

Ordering code

DN10 DN15 DN20 DN25 DN32 DN40 DN50

90 95 105 115 140 150 165

60 65 75 85 100 110 125

bolts

14 14

4xM12

16 18

Flange type: DIN 2527 or EN DIN 1092-1 Maximum pressure: PN40

4xM16

* Other dimensions are available on request. Please contact COMECO!

YPFSD - G4.G5.G6.G7.G8.G9.G10.G14

Code Feature or option

Code values

Probe diameter 'd' [mm]

3, 4.5, 5, 6, 8, 10

Insertion diameter 'F1' [mm]

13…21 (see table above) (1)

Shank length 'U' [mm]

50…1000 (2) (see table above) (1)

Extension length 'T' [mm]

0…100

Flange nominal size

DN10 (2), DN15, DN20, DN25, DN32, DN40, DN50, Z - other (specify!) (2)

Probe thread 'N' (1)

U1 - M18x1.5, U2 - M20x1.5, U3 - G3/8", U4 - G1/2", U5 - M27x2, U6 - G3/4", U8 - M14x1.5, Z - other (specify!) (2)

G10

Material

M1 - 1.4301, M2 - 1.4541, M3 - 1.4571 (2), M9 - 1.4404 or 1.4435, Z - other (specify!) (2)

G14

Flange face

A - flat (FF), B - raised (RF), D - groove, F - recess, G - O-ring recess, H - O-ring groove

Applicable for the selected probe diameter 'd' (2) Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

(1)

accessories

ANSI-FLANGED BORED STRAIGHT THERMOWELL

DIMENSIONS *

YPFSA N

H2 [mm]

H1 [mm]

F2 [mm]

d1 [mm]

F1 [mm]

3/8” NPT

25 + T

4 / 5.5

13…21

1/2" NPT

30 + T

7/9

15…21 / 17…21

3/4" NPT

35 + T

7 / 9 / 11

15…21 / 17…21 / 21

Material - stainless steel (see Appendix - Sheath materials) Application - with temperature gauges and TS probes

INSERTION LENGTH

Probe diameter: d = d1 - 1 Probe thread: G = N Probe length (incl. thread): n = 0.98 * L - e (fixed) or n ≈ L (spring-loaded) Maximum temperature: 850 °C Maximum pressure: 100 bar

d1 [mm]

U [mm]

max. 300

7...9

max. 700

max. 1000

FLANGE DIMENSIONS [mm] * SIZE class 1/2"

3/4"

1 ¼" L = U + b + H1 (flat face) or L = U + RF + b + H1 (raised face) 1 ½"

Fillet radius at root 1..3 mm Full penetration weld design is also available on request

150 300 600 900 150 300 600 900 150 300 600 900 150 300 600 900 150 300 600 900 150 300 600 900

88.9

60.5

95.2

66.5

9.7 12.7 14.2 22.3 11.2 14.2 15.7 25.4 12.7 16 17.5 28.4 14.2 18 20.6 28.4 16 19 22.3 31.7 17.5 20.8 25.4 38.1

120.6 98.6

82.5 69.8

117.3

82.5

130 108

88.9 79.2

124

88.9

149.3 117.3

101.6 88.9

133.4

98.6

158.7 127

111.2 98.6

155.4

114.3

177.8 152.4

123.9 120.6

165.1

127

215.9

165.1

RF 1.5 6.3 1.5

holes

15.7

19 6.3 1.5

Flange type: ANSI B16.5

22.3 15.7 4

19 6.3 1.5

25.4 15.7

(to fit thermowell specifications)

19 6.3 1.5

25.4 15.7

22.3 6.3 1.5 6.3

Maximum pressure: class 150 - 150 psig class 300 - 300 psig class 600 - 600 psig class 900 - 900 psig class 1500 - 1500 psig

22.3 15.7

Dimensions for classes 900 and 1500 are identical up to 2 ½" size!

28.4 19 8 25.4

* Other dimensions are available on request. Please contact COMECO!

YPFSA - G4.G5.G6.G7.G8'/8".G9.G10.G14

Code Feature or option

Code values

Probe diameter 'd' [mm]

3, 4.5, 5, 6, 8, 10

Insertion diameter 'F1' [mm]

13…21 (see table above) (1)

Shank length 'U' [mm]

50…1000 (2) (see table above) (1)

Extension length 'T' [mm]

0…100

G8'

Flange nominal size

50 - 1/2", 75 - 3/4", 100 - 1", 125 - 1¼", 150 - 1½", 200 - 2", Z - other (specify!) (2)

G8"

Flange nominal pressure (class)

150 - 10 bar (150 psig), 300 - 20 bar (300 psig), 600 - 40 bar (600 psig)

(1)

U9 - 3/8" NPT, U10 - 1/2" NPT, U11 - 3/4" NPT, Z - other (specify!) (2)

Probe thread 'N'

G10

Material

M1 - 1.4301, M2 - 1.4541, M3 - 1.4571 (2), M9 - 1.4404 or 1.4435, Z - other (specify!) (2)

G14

Flange face

A - flat (FF), B - raised (RF), D - groove, F - recess, G - O-ring recess, H - O-ring groove

(1)

Applicable for the selected probe diameter 'd' (2) Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Ordering code

accessories Flanged Welded Thermowell YPFW DIN-FLANGED WELDED THERMOWELL

YPFWD

DIMENSIONS * N

H [mm]

M14x1.5, G3/8”

M18x1.5

M20x1.5, G1/2"

M27x2, G3/4"

Material - stainless steel (see Appendix - Sheath materials) Application - with temperature gauges and TS probes

F2 [mm]

F1 x s [mm] 10x1.5, 10.2x2 (⅛"), 12x1.5, 13.5x2.35 (¼"), 14x2 10x1.5, 10.2x2 (⅛"), 12x1.5, 13.5x2.35, 14x2 (¼") 16x2, 17.2x2.35, 18x2, 20x2, 21.3x2.6 (½")

INSERTION LENGTH

Probe diameter: d < d1 or (F1- 2s) Probe thread: G = N Probe length (incl. thread): n = 0.98 * L - e (fixed) or n ≈ L - e (spring-loaded) Maximum temperature: 850 °C Maximum pressure: 25 bar (s = 1.5) or 40 bar (s ≥ 2)

F1 [mm]

U [mm]

≤ 12

max. 500

13...14

max. 1000

16...18

max. 1500

18...20

max. 2000

≥ 20

max. 2500

FLANGE DIMENSIONS *

L = U + b + H (flat face) or L = U + b + H + 2 (raised face)

Ordering code

NOMINAL SIZE

D [mm]

k [mm]

DN10 DN15 DN20 DN25 DN32 DN40 DN50

90 95 105 115 140 150 165

60 65 75 85 100 110 125

b d2 [mm] [mm]

bolts

Flange type: DIN 2527 or EN DIN 1092-1

14 14

4 x M12

16 18

Maximum pressure: PN10...PN40

4 x M16

(to fit thermowell specifications)

* Other dimensions are available on request. Please contact COMECO!

YPFWD - G4.G6.G8.G9.G10.G14

Code Feature or option

Code values

Tube diameter 'F1' [mm]

10, 10.2 (2), 12, 13.5 (2), 14, 16, 17.2, 18, 20, 21.3

Length 'U' [mm]

50…2500 (see table above) (1)

Flange nominal size

DN10 (2), DN15, DN20, DN25, DN32, DN40, DN50, Z - other (specify!) (2)

Probe thread 'N' (1)

U1 - M18x1.5, U2 - M20x1.5, U3 - G3/8", U4 - G1/2", U5 - M27x2, U6 - G3/4", U8 - M14x1.5, Z - other (specify!) (2)

G10

Material

M1 - 1.4301, M2 - 1.4541 (2), M3 - 1.4571 (2), M9 - 1.4404 or 1.4435, Z - other (specify!) (2)

G14

Flange face

A - flat (FF), B - raised (RF), D - groove, F - recess, G - O-ring recess, H - O-ring groove

(1)

COMECO reserves the right of changing specifications without prior notice!

Applicable for the selected tube diameter 'F1' (2) Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories

ANSI-FLANGED WELDED THERMOWELL

YPFWA

DIMENSIONS *

Material - stainless steel (see Appendix - Sheath materials) Application - with temperature gauges and TS probes

H [mm]

F2 [mm]

F1 x s [mm]

3/8” NPT

10x1.5, 10.2x2 (⅛"), 12x1.5, 13.5x2.35 (¼"), 14x2

1/2" NPT

10x1.5, 10.2x2 (⅛"), 12x1.5, 13.5x2.35, 14x2 (¼")

3/4" NPT

16x2, 17.2x2.35, 18x2, 20x2, 21.3x2.6 (½")

INSERTION LENGTH

Probe diameter: d < d1 or (F1- 2s) Probe thread: G = N Probe length (incl. thread): n = 0.98 * L - e + 0.4 * H (fixed) or n ≈ L - e + 0.4 * H (spring-loaded) Maximum temperature: 850 °C Maximum pressure: 25 bar (s = 1.5) or 40 bar (s ≥ 2)

F1 [mm]

U [mm]

≤ 12

max. 500

13...14

max. 1000

16...18

max. 1500

18...20

max. 2000

≥ 20

max. 2500

FLANGE DIMENSIONS [mm] * SIZE class ½"

¾"

1 ¼"

1 ½"

L = U + b + H (flat face) or L = U + RF + b + H (raised face)

150 300 600 150 300 600 150 300 600 150 300 600 150 300 600 150 300 600

88.9

60.5

95.2

66.5

98.6

69.8

9.7 12.7 14.2 11.2 14.2 15.7 12.7 16 17.5 14.2 18 20.6 16 19 22.3 17.5 20.8 25.4

117.3

82.5

108

79.2

124

88.9

117.3 133.4

98.6

127 155.4 114.3 152.4 120.6 165.1

127

holes

1.5 6.3

15.7 Flange type:

1.5 6.3 1.5 6.3 1.5 6.3 1.5 6.3 1.5

15.7

Maximum pressure:

class 150 - 150 psig class 300 - 300 psig class 600 - 600 psig

15.7 19 15.7

ANSI B16.5

(to fit thermowell specifications)

22.3 19

6.3

* Other dimensions are available on request. Please contact COMECO!

YPFWA - G4.G6.G8'/8".G9.G10.G14

Code Feature or option

(1) (2)

Code values

Tube diameters 'F1' [mm]

10, 10.2 (2), 12, 13.5 (2), 14, 16, 17.2, 18, 20, 21.3

Length 'U' [mm]

50…2500 (see table above) (1)

G8'

Flange nominal size

50 - ½", 75 - ¾", 100 - 1", 125 - 1¼", 150 - 1½", 200 - 2", Z - other (specify!) (2)

G8"

Flange nominal pressure (class)

150 - 10 bar (150 psig), 300 - 20 bar (300 psig), 600 - 40 bar (600 psig)

Probe thread 'N' (1)

U9 - 3/8" NPT, U10 - 1/2" NPT, U11 - 3/4" NPT, Z - other (specify!) (2)

G10

Material

M1 - 1.4301, M2 - 1.4541 (2), M3 - 1.4571 (2), M9 - 1.4404 or 1.4435, Z - other (specify!) (2)

G14

Flange face

A - flat (FF), B - raised (RF), D - groove, F - recess, G - O-ring recess, H - O-ring groove

Applicable for the selected tube diameter 'F1' Contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Ordering code

accessories Ceramic Protection Tubes YAC

CERAMIC PROTECTION TUBE

YAC MATERIAL

Material - alumina ceramics (see Appendix - Sheath materials) Application - T/C protection in gaseous chemical media

Maximum Temperature

CERAMIC PROTECTION TUBE (C2)

C 710

1600 °C

DIMENSIONS * F1 [mm]

d1 [mm]

Fitting Type

6 8 10 15 18 20 24 32

4.5 6 7 10 12 15 17 24

1, 5, 9 1, 5, 9 1, 5, 9 1, 5, 9 2, 5, 10 2, 6, 10 3, 6, 11 4, 7, 12

L [mm] 100÷1000

100÷2000

PROPERTIES Chemical Composition Flexural Strength

L ≈ n + m - 30

Thermal Shock Resist

good

Thermal Conductivity

20 W/m.K

Thermal Expansion

8.10-6 K-1 (0-1000 °C)

Porosity

Electrical Resitivity

CERAMIC PROTECTION TUBE (C3)

C 799

1700 °C

≥ 95% Al2O3 280 MPa

6 8 10 15 18 20 24 32

4.5 6 7 10 12 15 17 24

12 > 10 Ω.m (25°C)

1, 5, 9 1, 5, 9 1, 5, 9 1, 5, 9 2, 5, 10 2, 6, 10 3, 6, 11 4, 7, 12

100÷1000

100÷2000

PROPERTIES Chemical Composition Flexural Strength

L ≈ n + m - 30

> 99.7% Al2O3 360 MPa

Thermal Shock Resist

good

Thermal Conductivity

28 W/m.K

Thermal Expansion

9.10 K (0-1200°C)

Porosity

Electrical Resitivity

> 1012 Ω.m (25°C)

-6

-1

FITTING

Length 'm' [mm]

80 or 150

(1)

80 or 150 (1)

80 or 150

(1)

Material

stainless steel

TYPE

CONNECTION

½"

¾"

1 ¼"

½"

¾"

1 ¼"

½" x ½"

¾" x ½"

1" x ¾"

1 ¼" x ¾"

For tube length L ≥ 1000 mm

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA, tel: +359 32 646524, fax: +359 32 634089, e-mail: export@comeco.org

COMECO reserves the right of changing specifications without prior notice!

* Other dimensions are available on request. Please contact COMECO!

accessories

Ordering code

YAC - G10.G5.G6.G9'G9"

Code Feature or option Sheath material

(2)

Code values C2 - Alumina 95% (C 710), C3 - Alumina 99% (C 799)

Outer diameter 'OD' [mm]

from tables overleaf

Length 'L' [mm]

from tables overleaf

G9'

Fitting type

X - none, 1 - type 1, 2 - type 2, 3 - type 3, 4 - type 4, 5 - type 5, 6 - type 6, 7 - type 7, 8 - type 8, 9 - type 9, 10 - type 10, 11 - type 11, 12 - type 12, Z - other (specify!)

G9"

Fitting thread

G - parallel pipe threads, N - NPT threads, X - none *, Z - other (specify!)

Always ask for availability! * contact COMECO!

COMECO reserves the right of changing specifications without prior notice!

(2)

G10

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA, tel: +359 32 646524, fax: +359 32 634089, e-mail: export@comeco.org

accessories Metal Protection Tubes YAM YAM

Material - metals and metal alloys (see Appendix - Sheath materials) Application - temperature probe protection in athmospheres and baths

MATERIAL

Carbon Steel

WELDED PROTECTION TUBE (W)

1.4301 (AISI 304)

PROPERTIES Max. temperature Composition Thermal conductivity Composition

550 °C Mn0.8Si0.4C0.2 76 W/m.K Cr18Ni9Mn2Si1

Max. temperature

450 °C

Thermal conductivity 15 W/m.K 1.4404 (AISI 316L) 1.4571 (AISI 316Ti) 1.4841 (AISI 310)

1.4762 (AISI 446)

Titanium

100...500

M10

Kanthal  other

200...2000

~27

¾"

Atmospheres: oxidizing Baths: food products, mild acids and alkalis, petroleum

Max. temperature

1150 °C

Composition

Cr25Al2Si1

Atmospheres: oxidizing, sulpurous (NOT suitable for carburizing!) Baths: molten Pb, Sn, babbitt, neutral salt baths

1100 °C 2.4816 Composition Cr16Ni72Mn1 (Inconel 600) Thermal conductivity 14 W/m.K

200...2000

21~22

½"

Monel  (Alloy 400)

Max. temperature

550 °C

Composition

Ni63Cu34Mn2

Thermal conductivity 22 W/m.K 1050 °C 2.4602 Composition Cr21Mo14Wo3Co (Hastelloy C) Thermal conductivity 10 W/m.K Max. temperature

Hastelloy X

Max. temperature

1200 °C

Composition

Cr22Mo10Co2Wo

Thermal conductivity 10 W/m.K

Kanthal A

Max. temperature

1250 °C

Composition

Cr22Al6

Thermal conductivity 29 W/m.K 3.7035 Titanium Grade 2

BORED PROTECTION TUBE (B)

DIMENSIONS: * [mm]

Titanium

100...500

M10

other

200...800

~25

½"

Atmospheres: oxidizing, cryogenic Baths: food products, mild acids and alkalis, petroleum

850 °C Cr17Ni11Mo2 15 W/m.K 850 °C Cr17Ni13Mo2Ti 16 W/m.K 1150 °C Cr25Ni21Mn2 16 W/m.K

Thermal conductivity 14 W/m.K

[mm]

Atmospheres: non-oxidizing Baths: petroleum, molten Zn, Mg, Pb, Sn, babbitt

Max. temperature Composition Thermal conductivity Max. temperature Composition Thermal conductivity Max. temperature Composition Thermal conductivity

Max. temperature

DIMENSIONS: *

APPLICATION

Max. temperature

600 °C

Composition

99.2% Ti

Thermal conductivity 16 W/m.K

Atmospheres: oxidizing Baths: food products, petroleum increased resistance to acids Atmospheres: oxidizing, carburizing, nitriding Baths: general applications

Atmospheres: oxidizing, nitriding, mild sulphur and carburizing (up to 550 °C) Baths: salt (cyanide) baths Atmospheres: non-oxidizing Baths: salt waters, alkalis, and acids, but NOT oxidizing acids like nitric or nitrous. Atmospheres: oxidizing, carburizing, nitriding, chlorine Baths: acids, chlorides, brine and many aggressive chemicals Atmospheres: oxidizing, carburizing, sulpurous, nitriding, chlorine Baths: general applications Atmospheres: oxidizing, carburizing, sulpurous, nitriding, ammonia Baths: molten Cu, Zn, Mg Atmospheres: high aggressive gases Baths: high aggressive solvents

Carbon Steel

see above

1.4301 (AISI 304)

see above

1.4404 (AISI 316L)

see above

1.4571 (AISI 316Ti)

see above

3.7035 Titanium Grade 2

see above

Cast Iron GG-30 (ATSM A48)

Pure Iron

Max. temperature

700 °C

Composition

C3Si2Mn

Thermal conductivity 45 W/m.K Max. temperature

1300 °C

Composition

Atmospheres: oxidizing Baths: sulphur and caustic solutions some molten non-ferrous metals Baths: salt, cyanide, chloride

Thermal conductivity 80 W/m.K * Other dimensions are available on request. Please contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA, tel: +359 32 646524, fax: +359 32 634089, e-mail: export@comeco.org

COMECO reserves the right of changing specifications without prior notice!

METAL PROTECTION TUBE

accessories

Ordering code

YAM - G6.G9.G10

Code Feature or option G6

100…2000 (see tables overleaf)

Length 'L' [mm]

Connection thread 'G'

G10

Material (see tables overleaf)

(1)

(2)

(1)

G - parallel pipe threads, N - NPT threads, X - none *, Z - other (specify!) M1 - 1.4301, M3 - 1.4571, M4 - 1.4762 (1.4749), M5 - 1.4841, M8 - 2.4816 (Inconel 600), M9 - 1.4404(1.4435), M12 - cast iron, M13 - carbon steel, M14 - Kanthal® A, M18 - 2.4602 (Hastelloy C), M19 - Hastelloy X, M20 - Titanium alloy, M21 - Monel®, * Z - other (specify!)

Applicable for the selected design and material Always ask for availability! * contact COMECO!

COMECO reserves the right of changing specifications without prior notice!

(1)

Code values W - welded, B - bored

Design

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA, tel: +359 32 646524, fax: +359 32 634089, e-mail: export@comeco.org

accessories Ceramic Protection Tubes for Molten Metals YACM YACM

Material - silicon/carbon/alumina ceramics (see Appendix - Sheath materials) Application - T/C protection in molten metals and gaseous media

MATERIAL

Maximum Temperature

DIMENSIONS * F1 [mm]

d1 [mm]

Fitting Type

L [mm]

2, 3, 6, 11

230, 305, 460, 610, 760, 915, 1220



UCAR LT1  PROTECTION TUBE (C4) UCAR



LT1

1650 °C

PROPERTIES

Applicable metals:

L ≈ n + m - 30

Copper, Brass - up to 1150 °C Steel - up to 1375 °C (peak to 1735 °C) Zink, Lead, Tin, Silver, other metals

Chemical Composition

Non-applicable metals: Aluminum

SILICON CARBIDE PROTECTION TUBE (C5) SILICON CARBIDE

1380 °C

Flexural Strength Thermal Shock Resist

700 ∆T°C

Thermal Conductivity

29.4 W/m.K

Thermal Expansion

9.10 K (0-1000 °C)

Non-applicable metals: ferrous metals L ≈ n + m - 30

Porosity

0% conductive

2, 6, 10

3, 6, 11

4, 7, 12



HEXOLOY PROTECTION TUBE (C6) 1650 °C

85% SiC + 15% SiO2 250 MPa

Thermal Shock Resist

~500 ∆T°C

Thermal Conductivity

45 W/m.K

Thermal Expansion

5.10-6 K-1 (0-1200 °C)

Porosity

0.1 %

9.5

6.5

16 19 25 32 38

9.5 13 13 19 25

Non-applicable metals: ferrous metals

(Syalon 050)

150÷1370

Chemical Composition

98% SiC

Flexural Strength

380 MPa

Thermal Shock Resist

890 MPa @ 450 ∆T°C

Thermal Conductivity

30 W/m.K

Thermal Expansion

4.10-6 K-1 (0-1200 °C)

Porosity

0.6 %

Electrical Resitivity Syalon 101

107 Ω.m (25°C) 1, 5, 9 2, 5, 10 2, 6, 10 3, 6, 11 4, 7, 12 8

PROPERTIES

Aluminum, Copper, Brass, Zink, Lead, Tin, other non-ferrous metals

SYALON PROTECTION TUBE (C7)

200÷2000

Flexural Strength

Applicable metals:

L ≈ n + m - 30

200÷1000

Chemical Composition

Electrical Resitivity

-1

PROPERTIES

Aluminum, Copper, Brass, Zink, Lead, Tin, other non-ferrous metals

HEXOLOY

-6

Electrical Resitivity

Applicable metals:



77%Cr + 23% Al2O3 310 MPa

1200 °C (1400 °C)

12.5

6.5

16 22 28

9 12 16

10 Ω.m (25°C) 200÷1000 1, 5, 9 (no groove) 2, 5, 10 3, 6, 11 4, 7, 12

150÷2000

PROPERTIES Applicable metals:

Chemical Composition

90% Si3N4 + 6% Al2O3

Aluminum, Brass, Tin, Lead, Bismuth, Cadmium, Magnesium, Cast iron

Flexural Strength

760 MPa

Non-applicable metals: Copper, ferrous metals

L ≈ n + m - 30

Thermal Shock Resist

900 ∆T°C

Thermal Conductivity

28 W/m.K

Thermal Expansion

3.10 K (0-1200°C)

Porosity

Electrical Resitivity

1010 Ω.m (25°C)

-6

-1

* Other dimensions are available on request. Please contact COMECO!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA, tel: +359 32 646524, fax: +359 32 634089, e-mail: export@comeco.org

COMECO reserves the right of changing specifications without prior notice!

CERAMIC PROTECTION TUBE

accessories FITTING

Length 'm' [mm]

80 or 150

(1)

stainless steel

TYPE

CONNECTION

½"

¾"

1 ¼"

½"

¾"

1 ¼"

½" x ½"

¾" x ½"

1" x ¾"

1 ¼" x ¾"

For tube length L ≥ 1000 mm

Ordering code

YACM - G10.G5.G6.G9'G9"

Code Feature or option

Code values

G10

Sheath material (2)

C4 - UCAR LT1, C5 - silicon carbide, C6 - Hexoloy, C7 - Syalon

Outer diameter 'OD' [mm]

from tables overleaf

Length 'L' [mm]

from tables overleaf

G9'

Fitting type

X - none, 1 - type 1, 2 - type 2, 3 - type 3, 4 - type 4, 5 - type 5, 6 - type 6, 7 - type 7, 8 - type 8, 9 - type 9, 10 - type 10, 11 - type 11, 12 - type 12, Z - other (specify!)

G9"

Fitting thread

G - parallel pipe threads, N - NPT threads, X - none *, Z - other (specify!)

Always ask for availability! * contact COMECO!

COMECO reserves the right of changing specifications without prior notice!

(2)

(1)

Material

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA, tel: +359 32 646524, fax: +359 32 634089, e-mail: export@comeco.org

accessories Interface Cables

Schematic

Interface

Application

side "A"

side "B"

COMECO device

RS232 (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v1.16 or higher

COMECO device

RS232 (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v1.16 or higher

K1U

COMECO device

IA250T

Configuration: TRB-B, TRBI-B Software: "TraCon" v2.0 or higher

K2U

COMECO device

IA250T

Configuration: TRB-C, TRBI-C, TRZ Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: TRY, old TRB-C Software: "TraCon" (1)

K3U

COMECO device

USB (PC)

Configuration: TRY Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

IA100 interface adapter

RS232 (PC)

Standard RS232 cable

RS232

RS232 (PC)

Standard RS232 cable

USB 2.0 standard

Standard USB cable

K9U

COMECO device

USB (PC)

Configuration and power supply: RHV, TSOJ Software: "TraCon" (1)

K10U

COMECO device with RS485

IA250N

Configuration: COMECO devices Software: "PolyMonitor"

K11U

COMECO device

USB (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

K12U

COMECO device

USB (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v2.0 or higher

K13

OT801 serial printer

IA300

Configuration: IA300 data-logger Software: "InfoPrint"

K14

USB 2.0 standard

Standard USB cable

(1)

Contact COMECO

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Code

accessories

Code

Interface

Schematic

Application

side "A"

side "B"

K15U

COMECO device

USB (PC)

Configuration: old TRB-B Software: "TraCon" (1)

K16U

current loop

USB (PC)

Power supply: 15 VDC, max. 60 mA

COMECO device

RS232 (PC)

Configuration: TSOJ Software: "TraCon" (1)

K19U

COMECO device

USB (PC)

Configuration and power supply: TSOJ Software: "TraCon" (1)

KA1

COMECO device

K2, K2U, K5, K12U

Adapter â&#x20AC;&#x201C; simulates K1, K1U, K4, K11U Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

KIA

INOR device

RS232 (PC)

Configuration: TRSN-C (IPAQ-L) Software: "Ipro"

KIB

INOR device

RS232 (PC)

Configuration: TRSN-B (IPAQ-H) Software: "Ipro"

KIC

INOR device

RS232 (PC)

Configuration: TRP (ProfIPAQ) Software: "ProfiSoft"

KID

INOR device

RS232 (PC)

Configuration: TRSP (IPAQ-H/L+) Software: "Ipro"

DIN43650 4-pin (F)

DB-9 (F)

K19 *

USB-A (M)

COMECO reserves the right of changing specifications without prior notice!

DIN43650 4-pin (F)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Interface Cables

Schematic

Interface

Application

side "A"

side "B"

COMECO device

RS232 (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v1.16 or higher

COMECO device

RS232 (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v1.16 or higher

K1U

COMECO device

IA250T

Configuration: TRB-B, TRBI-B Software: "TraCon" v2.0 or higher

K2U

COMECO device

IA250T

Configuration: TRB-C, TRBI-C, TRZ Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: TRY, old TRB-C Software: "TraCon" (1)

K3U

COMECO device

USB (PC)

Configuration: TRY Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

IA100 interface adapter

RS232 (PC)

Standard RS232 cable

RS232

RS232 (PC)

Standard RS232 cable

USB 2.0 standard

Standard USB cable

K9U

COMECO device

USB (PC)

Configuration and power supply: RHV, TSOJ Software: "TraCon" (1)

K10U

COMECO device with RS485

IA250N

Configuration: COMECO devices Software: "PolyMonitor"

K11U

COMECO device

USB (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

K12U

COMECO device

USB (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v2.0 or higher

K13

OT801 serial printer

IA300

Configuration: IA300 data-logger Software: "InfoPrint"

K14

USB 2.0 standard

Standard USB cable

(1)

Contact COMECO

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Code

accessories

Code

Interface

Schematic

Application

side "A"

side "B"

K15U

COMECO device

USB (PC)

Configuration: old TRB-B Software: "TraCon" (1)

K16U

current loop

USB (PC)

Power supply: 15 VDC, max. 60 mA

COMECO device

RS232 (PC)

Configuration: TSOJ Software: "TraCon" (1)

K19U

COMECO device

USB (PC)

Configuration and power supply: TSOJ Software: "TraCon" (1)

KA1

COMECO device

K2, K2U, K5, K12U

Adapter â&#x20AC;&#x201C; simulates K1, K1U, K4, K11U Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

KIA

INOR device

RS232 (PC)

Configuration: TRSN-C (IPAQ-L) Software: "Ipro"

KIB

INOR device

RS232 (PC)

Configuration: TRSN-B (IPAQ-H) Software: "Ipro"

KIC

INOR device

RS232 (PC)

Configuration: TRP (ProfIPAQ) Software: "ProfiSoft"

KID

INOR device

RS232 (PC)

Configuration: TRSP (IPAQ-H/L+) Software: "Ipro"

DIN43650 4-pin (F)

DB-9 (F)

K19 *

USB-A (M)

COMECO reserves the right of changing specifications without prior notice!

DIN43650 4-pin (F)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Interface Cables

Schematic

Interface

Application

side "A"

side "B"

COMECO device

RS232 (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v1.16 or higher

COMECO device

RS232 (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v1.16 or higher

K1U

COMECO device

IA250T

Configuration: TRB-B, TRBI-B Software: "TraCon" v2.0 or higher

K2U

COMECO device

IA250T

Configuration: TRB-C, TRBI-C, TRZ Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: TRY, old TRB-C Software: "TraCon" (1)

K3U

COMECO device

USB (PC)

Configuration: TRY Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

IA100 interface adapter

RS232 (PC)

Standard RS232 cable

RS232

RS232 (PC)

Standard RS232 cable

USB 2.0 standard

Standard USB cable

K9U

COMECO device

USB (PC)

Configuration and power supply: RHV, TSOJ Software: "TraCon" (1)

K10U

COMECO device with RS485

IA250N

Configuration: COMECO devices Software: "PolyMonitor"

K11U

COMECO device

USB (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

K12U

COMECO device

USB (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v2.0 or higher

K13

OT801 serial printer

IA300

Configuration: IA300 data-logger Software: "InfoPrint"

K14

USB 2.0 standard

Standard USB cable

(1)

Contact COMECO

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Code

accessories

Code

Interface

Schematic

Application

side "A"

side "B"

K15U

COMECO device

USB (PC)

Configuration: old TRB-B Software: "TraCon" (1)

K16U

current loop

USB (PC)

Power supply: 15 VDC, max. 60 mA

COMECO device

RS232 (PC)

Configuration: TSOJ Software: "TraCon" (1)

K19U

COMECO device

USB (PC)

Configuration and power supply: TSOJ Software: "TraCon" (1)

KA1

COMECO device

K2, K2U, K5, K12U

Adapter â&#x20AC;&#x201C; simulates K1, K1U, K4, K11U Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

KIA

INOR device

RS232 (PC)

Configuration: TRSN-C (IPAQ-L) Software: "Ipro"

KIB

INOR device

RS232 (PC)

Configuration: TRSN-B (IPAQ-H) Software: "Ipro"

KIC

INOR device

RS232 (PC)

Configuration: TRP (ProfIPAQ) Software: "ProfiSoft"

KID

INOR device

RS232 (PC)

Configuration: TRSP (IPAQ-H/L+) Software: "Ipro"

DIN43650 4-pin (F)

DB-9 (F)

K19 *

USB-A (M)

COMECO reserves the right of changing specifications without prior notice!

DIN43650 4-pin (F)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Interface Cables

Schematic

Interface

Application

side "A"

side "B"

COMECO device

RS232 (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v1.16 or higher

COMECO device

RS232 (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v1.16 or higher

K1U

COMECO device

IA250T

Configuration: TRB-B, TRBI-B Software: "TraCon" v2.0 or higher

K2U

COMECO device

IA250T

Configuration: TRB-C, TRBI-C, TRZ Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: TRY, old TRB-C Software: "TraCon" (1)

K3U

COMECO device

USB (PC)

Configuration: TRY Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

IA100 interface adapter

RS232 (PC)

Standard RS232 cable

RS232

RS232 (PC)

Standard RS232 cable

USB 2.0 standard

Standard USB cable

K9U

COMECO device

USB (PC)

Configuration and power supply: RHV, TSOJ Software: "TraCon" (1)

K10U

COMECO device with RS485

IA250N

Configuration: COMECO devices Software: "PolyMonitor"

K11U

COMECO device

USB (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

K12U

COMECO device

USB (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v2.0 or higher

K13

OT801 serial printer

IA300

Configuration: IA300 data-logger Software: "InfoPrint"

K14

USB 2.0 standard

Standard USB cable

(1)

Contact COMECO

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Code

accessories

Code

Interface

Schematic

Application

side "A"

side "B"

K15U

COMECO device

USB (PC)

Configuration: old TRB-B Software: "TraCon" (1)

K16U

current loop

USB (PC)

Power supply: 15 VDC, max. 60 mA

COMECO device

RS232 (PC)

Configuration: TSOJ Software: "TraCon" (1)

K19U

COMECO device

USB (PC)

Configuration and power supply: TSOJ Software: "TraCon" (1)

KA1

COMECO device

K2, K2U, K5, K12U

Adapter â&#x20AC;&#x201C; simulates K1, K1U, K4, K11U Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

KIA

INOR device

RS232 (PC)

Configuration: TRSN-C (IPAQ-L) Software: "Ipro"

KIB

INOR device

RS232 (PC)

Configuration: TRSN-B (IPAQ-H) Software: "Ipro"

KIC

INOR device

RS232 (PC)

Configuration: TRP (ProfIPAQ) Software: "ProfiSoft"

KID

INOR device

RS232 (PC)

Configuration: TRSP (IPAQ-H/L+) Software: "Ipro"

DIN43650 4-pin (F)

DB-9 (F)

K19 *

USB-A (M)

COMECO reserves the right of changing specifications without prior notice!

DIN43650 4-pin (F)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Interface Cables

Schematic

Interface

Application

side "A"

side "B"

COMECO device

RS232 (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v1.16 or higher

COMECO device

RS232 (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v1.16 or higher

K1U

COMECO device

IA250T

Configuration: TRB-B, TRBI-B Software: "TraCon" v2.0 or higher

K2U

COMECO device

IA250T

Configuration: TRB-C, TRBI-C, TRZ Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: TRY, old TRB-C Software: "TraCon" (1)

K3U

COMECO device

USB (PC)

Configuration: TRY Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

IA100 interface adapter

RS232 (PC)

Standard RS232 cable

RS232

RS232 (PC)

Standard RS232 cable

USB 2.0 standard

Standard USB cable

K9U

COMECO device

USB (PC)

Configuration and power supply: RHV, TSOJ Software: "TraCon" (1)

K10U

COMECO device with RS485

IA250N

Configuration: COMECO devices Software: "PolyMonitor"

K11U

COMECO device

USB (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

K12U

COMECO device

USB (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v2.0 or higher

K13

OT801 serial printer

IA300

Configuration: IA300 data-logger Software: "InfoPrint"

K14

USB 2.0 standard

Standard USB cable

(1)

Contact COMECO

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Code

accessories

Code

Interface

Schematic

Application

side "A"

side "B"

K15U

COMECO device

USB (PC)

Configuration: old TRB-B Software: "TraCon" (1)

K16U

current loop

USB (PC)

Power supply: 15 VDC, max. 60 mA

COMECO device

RS232 (PC)

Configuration: TSOJ Software: "TraCon" (1)

K19U

COMECO device

USB (PC)

Configuration and power supply: TSOJ Software: "TraCon" (1)

KA1

COMECO device

K2, K2U, K5, K12U

Adapter â&#x20AC;&#x201C; simulates K1, K1U, K4, K11U Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

KIA

INOR device

RS232 (PC)

Configuration: TRSN-C (IPAQ-L) Software: "Ipro"

KIB

INOR device

RS232 (PC)

Configuration: TRSN-B (IPAQ-H) Software: "Ipro"

KIC

INOR device

RS232 (PC)

Configuration: TRP (ProfIPAQ) Software: "ProfiSoft"

KID

INOR device

RS232 (PC)

Configuration: TRSP (IPAQ-H/L+) Software: "Ipro"

DIN43650 4-pin (F)

DB-9 (F)

K19 *

USB-A (M)

COMECO reserves the right of changing specifications without prior notice!

DIN43650 4-pin (F)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Interface Cables

Schematic

Interface

Application

side "A"

side "B"

COMECO device

RS232 (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v1.16 or higher

COMECO device

RS232 (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v1.16 or higher

K1U

COMECO device

IA250T

Configuration: TRB-B, TRBI-B Software: "TraCon" v2.0 or higher

K2U

COMECO device

IA250T

Configuration: TRB-C, TRBI-C, TRZ Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: TRY, old TRB-C Software: "TraCon" (1)

K3U

COMECO device

USB (PC)

Configuration: TRY Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

IA100 interface adapter

RS232 (PC)

Standard RS232 cable

RS232

RS232 (PC)

Standard RS232 cable

USB 2.0 standard

Standard USB cable

K9U

COMECO device

USB (PC)

Configuration and power supply: RHV, TSOJ Software: "TraCon" (1)

K10U

COMECO device with RS485

IA250N

Configuration: COMECO devices Software: "PolyMonitor"

K11U

COMECO device

USB (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

K12U

COMECO device

USB (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v2.0 or higher

K13

OT801 serial printer

IA300

Configuration: IA300 data-logger Software: "InfoPrint"

K14

USB 2.0 standard

Standard USB cable

(1)

Contact COMECO

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Code

accessories

Code

Interface

Schematic

Application

side "A"

side "B"

K15U

COMECO device

USB (PC)

Configuration: old TRB-B Software: "TraCon" (1)

K16U

current loop

USB (PC)

Power supply: 15 VDC, max. 60 mA

COMECO device

RS232 (PC)

Configuration: TSOJ Software: "TraCon" (1)

K19U

COMECO device

USB (PC)

Configuration and power supply: TSOJ Software: "TraCon" (1)

KA1

COMECO device

K2, K2U, K5, K12U

Adapter â&#x20AC;&#x201C; simulates K1, K1U, K4, K11U Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

KIA

INOR device

RS232 (PC)

Configuration: TRSN-C (IPAQ-L) Software: "Ipro"

KIB

INOR device

RS232 (PC)

Configuration: TRSN-B (IPAQ-H) Software: "Ipro"

KIC

INOR device

RS232 (PC)

Configuration: TRP (ProfIPAQ) Software: "ProfiSoft"

KID

INOR device

RS232 (PC)

Configuration: TRSP (IPAQ-H/L+) Software: "Ipro"

DIN43650 4-pin (F)

DB-9 (F)

K19 *

USB-A (M)

COMECO reserves the right of changing specifications without prior notice!

DIN43650 4-pin (F)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Interface Cables

Schematic

Interface

Application

side "A"

side "B"

COMECO device

RS232 (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v1.16 or higher

COMECO device

RS232 (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v1.16 or higher

K1U

COMECO device

IA250T

Configuration: TRB-B, TRBI-B Software: "TraCon" v2.0 or higher

K2U

COMECO device

IA250T

Configuration: TRB-C, TRBI-C, TRZ Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: TRY, old TRB-C Software: "TraCon" (1)

K3U

COMECO device

USB (PC)

Configuration: TRY Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

IA100 interface adapter

RS232 (PC)

Standard RS232 cable

RS232

RS232 (PC)

Standard RS232 cable

USB 2.0 standard

Standard USB cable

K9U

COMECO device

USB (PC)

Configuration and power supply: RHV, TSOJ Software: "TraCon" (1)

K10U

COMECO device with RS485

IA250N

Configuration: COMECO devices Software: "PolyMonitor"

K11U

COMECO device

USB (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

K12U

COMECO device

USB (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v2.0 or higher

K13

OT801 serial printer

IA300

Configuration: IA300 data-logger Software: "InfoPrint"

K14

USB 2.0 standard

Standard USB cable

(1)

Contact COMECO

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Code

accessories

Code

Interface

Schematic

Application

side "A"

side "B"

K15U

COMECO device

USB (PC)

Configuration: old TRB-B Software: "TraCon" (1)

K16U

current loop

USB (PC)

Power supply: 15 VDC, max. 60 mA

COMECO device

RS232 (PC)

Configuration: TSOJ Software: "TraCon" (1)

K19U

COMECO device

USB (PC)

Configuration and power supply: TSOJ Software: "TraCon" (1)

KA1

COMECO device

K2, K2U, K5, K12U

Adapter â&#x20AC;&#x201C; simulates K1, K1U, K4, K11U Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

KIA

INOR device

RS232 (PC)

Configuration: TRSN-C (IPAQ-L) Software: "Ipro"

KIB

INOR device

RS232 (PC)

Configuration: TRSN-B (IPAQ-H) Software: "Ipro"

KIC

INOR device

RS232 (PC)

Configuration: TRP (ProfIPAQ) Software: "ProfiSoft"

KID

INOR device

RS232 (PC)

Configuration: TRSP (IPAQ-H/L+) Software: "Ipro"

DIN43650 4-pin (F)

DB-9 (F)

K19 *

USB-A (M)

COMECO reserves the right of changing specifications without prior notice!

DIN43650 4-pin (F)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Interface Cables

Schematic

Interface

Application

side "A"

side "B"

COMECO device

RS232 (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v1.16 or higher

COMECO device

RS232 (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v1.16 or higher

K1U

COMECO device

IA250T

Configuration: TRB-B, TRBI-B Software: "TraCon" v2.0 or higher

K2U

COMECO device

IA250T

Configuration: TRB-C, TRBI-C, TRZ Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: TRY, old TRB-C Software: "TraCon" (1)

K3U

COMECO device

USB (PC)

Configuration: TRY Software: "TraCon" v2.0 or higher

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

COMECO device

RS232 (PC)

Configuration: old TRB-B Software: "TraCon" (1)

IA100 interface adapter

RS232 (PC)

Standard RS232 cable

RS232

RS232 (PC)

Standard RS232 cable

USB 2.0 standard

Standard USB cable

K9U

COMECO device

USB (PC)

Configuration and power supply: RHV, TSOJ Software: "TraCon" (1)

K10U

COMECO device with RS485

IA250N

Configuration: COMECO devices Software: "PolyMonitor"

K11U

COMECO device

USB (PC)

Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

K12U

COMECO device

USB (PC)

Configuration: TRB(I)-C, TRC-C, TRZ Software: "TraCon" v2.0 or higher

K13

OT801 serial printer

IA300

Configuration: IA300 data-logger Software: "InfoPrint"

K14

USB 2.0 standard

Standard USB cable

(1)

Contact COMECO

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

COMECO reserves the right of changing specifications without prior notice!

Code

accessories

Code

Interface

Schematic

Application

side "A"

side "B"

K15U

COMECO device

USB (PC)

Configuration: old TRB-B Software: "TraCon" (1)

K16U

current loop

USB (PC)

Power supply: 15 VDC, max. 60 mA

COMECO device

RS232 (PC)

Configuration: TSOJ Software: "TraCon" (1)

K19U

COMECO device

USB (PC)

Configuration and power supply: TSOJ Software: "TraCon" (1)

KA1

COMECO device

K2, K2U, K5, K12U

Adapter â&#x20AC;&#x201C; simulates K1, K1U, K4, K11U Configuration: TRB(I)-B, TRC-B, TROJ Software: "TraCon" v2.0 or higher

KIA

INOR device

RS232 (PC)

Configuration: TRSN-C (IPAQ-L) Software: "Ipro"

KIB

INOR device

RS232 (PC)

Configuration: TRSN-B (IPAQ-H) Software: "Ipro"

KIC

INOR device

RS232 (PC)

Configuration: TRP (ProfIPAQ) Software: "ProfiSoft"

KID

INOR device

RS232 (PC)

Configuration: TRSP (IPAQ-H/L+) Software: "Ipro"

DIN43650 4-pin (F)

DB-9 (F)

K19 *

USB-A (M)

COMECO reserves the right of changing specifications without prior notice!

DIN43650 4-pin (F)

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,

accessories Tag Label TL TAG LABEL

Material - aluminum or stainless steel (see Appendix - Sheath materials) Application - with TS and LC probes

SPECIFICATIONS * Area 2 [cm ]

Dimensions [mm]

Width [mm]

Font Size

Rows

Graphics

2...50

min. 10 (X/Y axis)

0.5...1.5

min. 8 pt

1...4

vector only

Technology: laser cut and engraved

* Exact shape, dimensions, design, and text according to customer specs!

(example)

Ordering code

TL - G1.G4.G6.G10

Code Feature or option

Code values

Number of rows

1, 2, 3, 4

Area [cm2]

2â&#x20AC;Ś50

Width

5 - 0.5 mm, 10 - 1.0 mm, 15 - 1.5 mm

G10

Material

AL - aluminum, M1 - 1.4301, M9 - 1.4404 (1.4435)

COMECO reserves the right of changing specifications without prior notice!

Comeco Inc., P.O.Box 378, Plovdiv 4000, BULGARIA,