D #953-000-003eN AerO precisiON uLTrALiGHT scOpe MOuNT See

Provides Extra Clearance For Long Eye Relief Scope; Ring-Top Slots For Additional Accessories

One-piece cantilever mount with integral rings positions the optic almost 2" farther forward to provide extra clearance needed for a night vision device (NVD), add-on magnifier, or long eye relief scope. The “Proper Eye Position Ready” mount also features built-in, two-slot rails on the tops of the rings for convenient mounting of reflex sights or other accessories. Each top ring strap is secured with six Torx® screws to prevent recoil-induced slippage. Side locking bar with two, steel hex nuts and cross-bolts hold tight on any Picatinny receiver rail. Also available with quick-release lever (QD) system. SPECS: Aluminum, hardcoat anodized, matte black. 5.3" (13.5cm) long, 1.6" (4.1cm) wide, 2.4" (6.1cm) overall height. Height from top of rail to bottom of ring: 1" (2.5cm). 8.7 oz. (247g) weight. Fits scopes with 1" tube. Mounts to MIL-STD 1913 Picatinny rails. #118-000-028EN 1" P.E.P.R. Mount, 8A80P99 � � � � � � � � � $ 80.99 #118-000-038EN 1" QD P.E.P.R. Mount, 8A107H99� � � � � 107.99 749-101-260EN 30mm P.E.P.R. Scope Mount, 8A80A99 � � � � � � � � � � � � � � � � � � � � � � � � � � 80.99 #118-000-036EN 30mm QD P.E.P.R. Mount, 8A107H99 � � 107.99 #118-000-123EN 34mm P.E.P.R. Mount, 20 MOA, 8A103K21� � � � � � � � � � � � � � � � � � � � � � � � � � 107.99

DNZ PRODUCTS AR-15/M16 FREEDOM REAPER SCOPE MOUNT

Perfectly Aligns Scope For Best Accuracy; Easy Removal & Reinstallation

One-piece scope base with integral rings speeds installation and puts your scope in perfect alignment for precise targeting. Clamps directly to Picatinny rail on flattop receiver, and lets you remove and reattach the scope and mount as a single unit, without loss of zero. Enables fast, easy change of scope position for eye relief adjustment. Eliminates scope damage caused by over-tightened or misaligned scope rings; no ring lapping required. Machined from a single piece of lightweight billet aluminum for exceptional strength. Models for 1" or 30mm O.D. tubes. a b SPECS: Aluminum, hardcoat anodized, matte black finish. 41/4" (10.8cm) long, 11/2" (3.8cm) wide, 1.375" (3.54cm) high from top of base to center of ring. #100-004-893EN 1" Scope Mount, 9C98N00 � � � � � � � � $ 104.99 #100-004-894EN 30mm Mount, 9C115N66 � � � � � � � � � � 124.99

NIGHTFORCE ULTRALITE MAGMOUNT

For Ultra-Secure, Recoil-Resistant Mounting Of Large Scopes

Offering the same one-piece QD concept as the Nightforce UniMount, the Ultralite™ MagMount™ has a third crossbolt for even greater protection against recoil. Tall enough to allow clearance of 56mm objective riflescopes when mounted on a continuous rail. MagMount does not have built-in elevation. Available for 30mm and 34mm scope tubes. a b SPECS: Machined 7075 T6 aluminum, hardcoat finish, matte black. Heights measured from top of receiver rail to centerline of scope. #100-012-609EN 30mm MagMount, 1.375" High, 2E286K00 � � � � � � � � � � � � � � � � � � � � � � � � $ 286.00

Rock Solid Mount That Weighs Only 3 Oz.

Ultra-lightweight, one-piece scope mount locks securely on any Picatinny receiver rail with a rock solid fit. A side locking bar with three Torx® head bolts and three cross bars that drop into the rail slots ensure this mount won’t budge. Vertically split rings have grooved locking system and two Torx® screws to firmly hold the scope against recoil-induced slippage. Torx wrenches included. Models for 1" or 30mm scope tubes. a b SPECS: 6061 T6 aluminum, hardcoat anodized, matte black, flat dark earth (FDE), or O.D. green (ODG). 4¾" long x 13/16" wide x 2½" high. 3.1 oz. wt. #953-000-002EN 1" Ultralight Scope Mount , 3E00JFD � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 79.99 #953-000-003EN 30mm Ultralight Scope Mount, Black, 3E00IQG � � � � � � � � � � � � � � � � � � � � � � � � � � � 79.99 953-000-011EN 30mm Ultralight Scope Mount, FDE, 3E84B99 � � � � � � � � � � � � � � � � � � � � � � � � � � � 84.99 953-000-012EN 30mm Ultralight Scope Mount, ODG, 3E94A99 � � � � � � � � � � � � � � � � � � � � � � � � � � � 94.99

ULTRALIGHT EXTENDED & SPR SCOPE MOUNTS - Rigid, minimalist mount has the rear ring pushed farther forward for use with optics that require extra eye relief. Extended mount has the rear ring 1" farther forward, while the SPR mount positions the rear ring 2" forward, making it ideal for use with the high-end optics often Extended used on “Special Project Rifles”. Excellent mounts for optics with short body tubes, also. Still offers three strong crossbolts for installation on MIL-STD 1913 Picatinny rails, with a cross-slot keyway, SPR provides excellent recoil protection. 953-000-007EN 1" Extended Scope Mount, Black, 3E89H99 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 89.99 953-000-008EN 30mm Extended Scope Mount, Black, 3E89F99 � � � � � � � � � � � � � � � � � � � � � � � � � � 89.99 953-000-009EN 30mm Extended Scope Mount, FDE, 3E99J99 � � � � � � � � � � � � � � � � � � � � � � � � � � 99.99 953-000-010EN 30mm Extended Scope Mount, ODG, 3E99B99 � � � � � � � � � � � � � � � � � � � � � � � � � � 99.99 953-000-013EN 30mm SPR Scope Mount, Black, 3E94J99 � � � � � � � � � � � � � � � � � � � � � � � � � � 94.99 953-000-014EN 30mm SPR Scope Mount, FDE, 3E104Q99 � � � � � � � � � � � � � � � � � � � � � � � � � 104.99 953-000-015EN 30mm SPR Scope Mount, ODG, 3E104Q99 � � � � � � � � � � � � � � � � � � � � � � � � � 104.99

ULTRALIGHT CANTILEVER SCOPE MOUNT - Single-ring version of the mount above is ideal for mounting a red dot optic on a flattop reciever. Offers the proper height for absolute co-witness with factory “iron” sights. Accepts both optics with 1" or 30mm tubes. SPECS: 6061 T6 aluminum, hardcoat anodized, matte black, flat dark earth (FDE), or O.D. green (ODG). 25/8" long, 11/16" wide, 25/8" high. 1.6 oz. wt. Includes Torx wrench and instructions. #953-000-004EN 30mm Cantilever Mount, Black, 3E00BAJ � � � � � � � � � � � � � � � � � � � � � � � � � � $ 57.99 953-000-006EN 30mm Cantilever Mount, FDE, 3E89N99 � � � � � � � � � � � � � � � � � � � � � � � � � � 89.99 953-000-005EN 30mm Cantilever Mount, ODG, 3E89E99 � � � � � � � � � � � � � � � � � � � � � � � � � � 89.99 Rock-Solid Mounts With Quick-Detach System

Quick-release lever-lock system clamps solidly to flattop rail and will not work loose even under heavy recoil—the more force acting on the lever, the tighter it locks. Depress the release tab to swing the lever open, and the mount easily lifts off the rifle. Adjustable with a flat head screwdriver or even a coin for an ultrasecure, no-slip fit on any Picatinny rail, including over- or undersized commercial rails. Lever may be configured to lock to the front or the rear to suit the operator’s preference. Large locking bar on the side of the mount engages the maximum amount of rail area, while the crossbolt and two integral locking lugs ensure rock-solid engagement of rail slots to prevent movement under recoil. Five heavy duty steel hex head screws (three on top, two on bottom) clamp the vertically split ring halves together. Cutouts in the ring sides and in the base reduce weight without sacrificing strength. a b

AD-68 AIMPOINT MOUNT - Designed for Aimpoint optics or similar aiming devices requiring a single, 30mm ring, including the Comp C3 and M2/ML2/M3/ML3 series. Available in four configurations to suit a variety of mounting needs. Standard co-witnesses “iron” sights near the center of the optic when mounted on an AR-15/ M16/M4 with standard-height mil-spec sights. Low positions the scope as close as possible to the top of the receiver. High positions the backup sight picture in the lower 1/3 of the optic viewing area. Cantilever provides same co-witness elevation as High mount and positions the Aimpoint 1½" forward to provide room for rear-mounted night-vision device or Aimpoint 3X Magnifier. SPECS: 6061 T6 aluminum, hardcoat anodized, matte black. Height measured from top of rail to bottom of scope body. Standard - .940" high. Low - .520" high. High – 1.120" high. Cantilever - 1.120" high. #100-003-650EN Standard Aimpoint Mount, 7B100Q00� � � � � � � � � � � � � � � � � � � � � � � � $ 105.00 #100-003-652EN Low Aimpoint Mount, 7B100C00� � � 105.00 #100-003-651EN High Aimpoint Mount, 7B100N00 � � 105.00 #100-003-649EN Cantilever Aimpoint Mount, 7B128C57 � � � � � � � � � � � � � � � � � � � � � � � � 135.00

AD-B2 ACOG MOUNT - Mount replaces original factory base on 1.5x, 2x, and 3x Trijicon ACOG scopes and allows quick-detach installation on Picatinny receiver rails. Attaches with two steel Torx® screws (included) for a tight hold under heavy recoil. SPECS: 6061 T6 aluminum, hardcoat anodized, matte black. Height measured from top of rail to bottom of scope body - .25" (7.8mm). Fits 1.5x, 2x, and 3x ACOG only. #100-004-583EN AD-B2 Mount, 7B63J19� � � � � � � � � � � � � $ 65.95

AD-RECON MOUNT - All-in-one mount combines a rock-solid platform for mounting high-power optics on flattop rails with the versatility of a quick-detach tactical mount. Dual release lever system grabs the rail in two places. Cantilever gives plenty of room to achieve both proper eye relief and height above receiver with conventional scopes – no need for an extended riser or separate rings. SPECS: 6061 T6 aluminum, hardcoat anodized, matte black. 6" (15.2cm) long, 17/8" (4.8cm) wide, 21/2" (63.5cm) high. 2½" space between rings. Centerline of rings is 1½" (3.81cm) above the rail. Models available to fit 1" and 30mm O.D. scope tubes. #100-005-757EN 1" AD-RECON Mnt, 7B157M14 � � � � � � �$ 179.95 #100-005-758EN 30mm AD-RECON Mount, 7B157P14 � � � � � � � � � � � � � � � � � � � � � � � � � � 179.95

AD-RECON-H/X SCOPE MOUNTS - One-piece integral base and rings with dual-lever system provides a quick attach/detach platform for mounting optics onto flattop-style AR-15s. Extra-high mounts are available in two different lengths for proper eye relief or night-vision device attachment. AD-RECON-H cantilever positions optics forward, leaving 1½" space to the rear of the back ring. AD-RECON-X uses the same cantilever design, but places the optics farther forward leaving 2¾" space to the rear of the back ring. Models available for 1" and 30mm scope tubes. SPECS: 6061-T6 Aluminum, T3 mil-spec anodized, matte black. 8 oz (226g) wt. (all models). Heights measured from top of rail to centerline of scope tube. AD-RECONH – 6" (15.2cm) OAL. 1" and 30mm model – 17/8" (4.7cm) height. 2½" (6.3cm ) space between rings. AD-RECON-X – 7" (17.8cm) OAL. 1" model – 13/8" (3.5cm) height. 30mm model – 1½" (3.7mm) height. 2¼" (5.7cm) space between rings. #100-006-229EN AD-RECON-H Mnt, 1", 7B168P57 � � � $ 182.95 #100-005-761EN AD-RECON-H Mount, 30mm, 7B168K57� � � � � � � � � � � � � � � � � � � � � � � � � 182.95 #100-005-759EN AD-RECON-X Mnt, 1", 7B168K57� � � � 189.95 #100-005-760EN AD-RECON-X Mount, 30mm, 7B168B57� � � � � � � � � � � � � � � � � � � � � � � � � 189.95

AD-SCOUT OPTICS MOUNT - One-piece integral base and rings designed for traditional optics or similar sights that require two, 30mm rings for additional support. Available in three different lengths for proper eye relief adjustment. AD-Scout-S is standard length for mounting traditional optics. AD-Scout Cantilever positions optics farther forward to provide 1½" of extra space at the rear for mounting night-vision devices or when additional eye-relief is needed. AD-Scout-X uses the same great cantilever design as the AD-Scout Cantilever, but positions optics 2½" farther forward for maximum room at the rear for mounting night-vision devices or making eyerelief adjustments. SPECS: 6061 T6 aluminum, hardcoat T3 mil-spec anodized, matte black. Height measured from top of rail to bottom of scope body - .87" (2.2cm) high. Distance between rings - 21/2" (6.3cm.) high. 7.1 ounces (201g) weight. AD-Scout - S - 41/2" (11.4 cm) OAL. AD-Scout Cantilever - 6" (15.2cm) OAL. AD-Scout -X - 7" (17.8cm) OAL. #100-004-026EN AD-Scout-S Mount, 7B121G43 � � � � � $ 134.95 #100-004-025EN AD-Scout Cantilever Mount, 7B135C71� � � � � � � � � � � � � � � � � � � � � � � � � 149.95 #100-004-027EN AD-Scout-X Extended Cantilever Mount, 7B150K00� � � � � � � � � � � � � � � � � 164.95

QUICK-RELEASE SCOPE MOUNT - Onepiece base with dual-lever system provides the same solid mounting and fast removal and reattachment of AD-68 Aimpoint Mount for traditional scopes requiring two rings. Models available for 1" and 30mm rings. SPECS: 6061 T6 aluminum, hardcoat anodized, matte black. 4½" (11.4cm) long. Each ring covers 1" (2.5cm) of scope tube length. Height measured from top of rail to bottom of scope body (both models): .890" #100-003-653EN 1" Scope Mount, 7B142H86 � � � � � � � � �$ 159.95 #100-003-654EN 30mm Scope Mount, 7B142K86 � � � � � 159.99

AD-T1-L AIMPOINT MICRO MOUNT - Lightweight, quick-detach mount lets you install and remove your Aimpoint Micro series red dot in seconds. Replaces original factory base and secures to the Aimpoint sight with four, high-strength, steel Torx® screws for a tight hold under heavy recoil. SPECS: 6061 T6 aluminum, hardcoat T3 mil-spec anodized, matte black. Height measured from top of rail to bottom of scope body - .31" (7.8mm). Fits Aimpoint Micro series red dot sights only. #100-004-024EN Aimpoint T1-L Micro Mount, 7B69K95 � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 69.95