Solvent Extraction Method for the Separation of Cerium(III) as Cations From Aqueous Media By use 4-[ by Taghreed H Alnoor

Ministry of Higher Education and Scientific Research

Journal of Kufa for Chemical Science A refereed Research Journal I Chemical Science Vol. 1, No. 10 Year 2015 ISSN 2077 - 2351

Address: Iraq – Najaf – University of Kufa Box (190) www. Edu_grils. Kuiraq.com

E-mail: Edu_grils@Kuiraq.com

EDITOR BOARD Prof. Dr. Shawket Kadhim Jawad / Editor in Chief Ass. Prof. Faez Abdul-Hussein Alrammahi / Editor in Director / Member Prof. Dr. Hassan Thamir Ghanim / Member Prof. Dr. Noori Yousif Al-Ankoshi / Member Ass. Prof. Dr. Izzat HUssain Zamam Al-Awadi / Member Ass. Lecturer JIhan Razzaq Muslim / Editor in Secretary / Member

CONSULTATION BOARD Prof. Dr. Gazi Adb Al-Wahab / University of Sery Prof. Dr. Falih Hassan Musa/ University of Baghdad Prof. Dr. Bahjet Razzaq Jaafer Muhi Al-diin / University of Kufa Prof. Dr. Issam Muhammed Ali / University of Baghdad Prof. Dr. Khulod Abd Salih Al Saadi / University of Baghdad Prof. Dr. Zuhair Abd Al-Ameer Khammas /University of Baghdad Prof. Dr. Mahdi Muhammed Ruda Al- Sahlawi /University of Baghdad

‫مجلة الكوفة لعلوم الكيمياء‬ Journal of Kufa for Chemical Science Vol.1, No. 10 - November 2015

Articles

Title and Authors

Page

Study on Synthesized Polyamide Surfactant 1

as a Corrosion Inhibitor

1-7

Mahmoud Sh. Hussain Liquid Ion Exchange for Extraction and Spectrophotometric 2

Determination of Tungestate WO4˭ by Use Azo-derivative.

8-20

Shawket K. Jawad and Nadia M. Muslim Liquid Ion Exchange Method for Extraction of Pb (II) as Anion by Using 15C5 Coupled with Spectrophotometric Determination 3

in Different Samples

21-37

Safa Majeed Hameed, R. K. Al-Kubaisy and Khalil Ibraheem Hussain Synthesis,Characterization of Some Metal Complexes with bis[O,O-2,3;O,O-5,6-(thiol(carboxylic)methylidene)]-L-Ascorbic 4

Acidand Studies their Biological Activity

38-55

Fawzi Yahya Waddai, Falih Hassan Musa, Huda Ahmed Fidhel Solvent Extraction Method for the Separation of Cerium(III) as Cations From Aqueous Media By use 4-[N-(5-methyl isoxazol5

3-yl)benzene sulfonamide azo]-1- Naphthol Coupled With

56-73

Spectroscopic Method For Determination Sahar Akeel Hussein , R. K. Al-Kubaisy and Taghreed H. Al-Noor Synthesis and Characterization of Some Transition Metal Complexes with New Schiff Base Ligand Derivative from Isatin. 6

Ebtihal Kadhum Kareem Sajid M. Lateef Abbas Abid Ali Drea

74-85

Cloud Point Extraction Method for Separation, Extraction and Spectrophotometric Determination of Zn(II) and Ni(II) as 7

Chloro Anion Complex by use of Crystal Violet

86-103

Jihan R. Muslim Synthesis and Characterization of new 3-(4-acetylphenyl) -2(4-nitrophenyl) thiazolidin-4-one derivatives 8

Nisreen Kais Abood , Hanan Ghadban Sha'aban and Nagham

104-112

majed Abd-Alhassan Preparation, Spectral Characterization of New Mixed Ligand 9

Complexes with Dithiocarbamate Ashwaq .S, AL-Saada,Hussain .Abid AL-Kafajy, Ahmed,T.Numan

113-120

‫مجلة الكوفة لعلوم الكيمياء‬ ‫‪Journal of Kufa for Chemical Science‬‬ ‫‪Vol. 1, No. 10 - November 2015‬‬

‫‪Page‬‬

‫‪Title and Authors‬‬

‫‪Articles‬‬

‫فصل مزيج المركبات الفينولية على بعض األطوار السائلة الثابتة‬ ‫‪1-12‬‬

‫باستخدام تقنية كروماتوغرافيا الغاز‬ ‫هبة قيس كمال ‪ ,‬قاسم كاظم األسدي‪ ,‬سجى صالح جبار‬

‫‪1‬‬

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015

Solvent Extraction Method for the Separation of Cerium(III) as Cations From Aqueous Media By use 4-[N-(5-methyl isoxazol-3yl)benzene sulfonamide azo]-1- Naphthol Coupled With Spectroscopic Method For Determination Sahar Akeel Hussein , R. K. Al-Kubaisy and Taghreed H. Al-Noor Chemistry Department-College of Education for Pure Science-Ibn Al-Haitham Baghdad University Email: ffsahar060@gmail.com

‫الخالصة‬ N-(5-methyl isoxazol-3-yl)benzene sulfonamide ‫ من الطور المائي باستعمال الكاشف‬Ce3+ ‫تم استخالص أيونات السيريوم‬ ‫ من الطور المائي كمعقد ترابط ايوني كان‬Ce3+ ‫ ألستخالص ايونات‬pHex ‫ وقد اظهرت القيمة المثلى للدالة الحامضية‬azo]-1- Naphthol ‫ في الطور المائي باستعمال الكاشف‬Ce3+ ‫ كذلك تجربة االستخالص لتراكيز مختلفة من ايونات‬.(D) ‫( الذي أعطى قيمة نسبة التوزي‬pH = 9) ‫( من جانب آخر‬D) ‫ يعتبر هو التركيز االمثل الذي يعطي أعلى قيمة لنسبة التوزي‬100 μg Ce3+ ‫العضوي و مذاب في الكلوروفورم أظهرت ان‬ ‫( كان هو الزمن االمثل الذي يعطي أعلى قيمة لنسبة‬10 min.) ‫تجربة االستخالص حول تأثير زمن الرج فقد أظهرت ان الرج لزمن مقدارم‬ ‫ اما دراسة تركيب معقد الترابط األيوني المستخلص إلى الطور العضوي فقد تمت بإجراء اربعه أنواع من التجارب وهي طريقة‬. (D) ‫التوزي‬ ‫تحليل الميل وطريقة النسب المو لية وطريقة التغيرات المستمرة وقد أثبتت التجارب الثالث بان لمعقد الترابط األيوني المستخلص الى الطور‬ ‫ إما دراسة تأثير المذيب العضوي على عملية االستخالص فقد أثبتت التجربة‬. 1:1 (M : L) ‫العضوي له تركيب ساندويج بنسبة مولية‬ ‫باستخدام عدد من المذيبات العضوية المخت لفة في ثابت العزل الكهربائي لها انه ليس هناك اية عالقة خطية بين ثابت العزل الكهربائي للمذيبات‬ ‫( في هذم المذيبات ولكن أظهر مذيب الكلوروفورم تأثير ملحوض على عملية االستخالص وأعطى أعلى‬D) ‫العضوية المختلفة وقيم نسب التوزي‬ .(D) ‫قيم لنسب التوزي‬

Abstract Extraction experiments for Ce+3 ion from aqueous phase by new laboratory prepared Azo derivation as complexation agent 4- [N-(5-methyl isoxazol-3-yl)benezen sulfonamide azo]-1- Naphthol (AMBN) shows the optimum conditions for this extraction method was (pH= 9) (10 minutes) shaking time and 100µg (1.5x10-4M) concentration of Ce+3 ion in aqueous phase. Organic solvents effect study shows there is not any linear relation between distribution ratio (D) for extraction of Ce +3 ion and dielectric constant (ε)for organic solvents used but there is un effect for organic solvent structure on the extraction of Ce +3 ion and distribution ratio (D) values. Stoichiometric studies demonstrated the more probable structure ion pair complex extracted for Ce+3 was 1:1 . Key word: Cerium(ΙΙ) , Solvent extraction , 4- [N-(5-methyl isoxazol-3-yl)benezen sulfonamide azo]-1- Naphthol.

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015 Introduction

Previously used the azo compounds and its derivatives for the extraction methods and used to spectrophotometric determination of transition elements, determination of Ce(IV)using acetophenone 2,5dihydroxy, semicarbazone. The complex has been quantitatively extracted into n-Butanol at pH 4.0.The molar absorptivity is 2564.1 L mol-1cm-1 and Sandell’s sensitivity is 0.02484 µg cm-2 respectively. This method applied to determination of Ce(IV) synthetic and commercial samples[1]. Recover La and Ce from Indian red mud in sulfuric acid medium. The method includes acid leaching of red mud pulp and subsequent liquid–liquid extraction of the leached metals with different organic extractants, in order to establish the technical feasibility of extraction and separation simultaneously. Maximum recovery of La (99.9%) was recorded with 3 M H2SO4 at ambient (35 °C) temperature, S/L ratio of 10 g/L and agitation rate of 200 rpm in 1 h time. While 99.9% Ce recovery was achieved at 75 °C and solid/liquid ratio of 10 g/L in 3 M H2SO4. Significant specificity for complete extraction of La, Ce and Sc by Cyanex 301 was noted as compared to the solvents such as DEHPA and Cyanex 272[2]. A spectrophotometric method has been developed for the determination of Ce(IV) using Hydrazinecarboxymide2-[(2-hydroxyphenyl) methylene-1 as an extractive reagent. The reagent forms a light yellow colored complex which has been quantitatively extracted into n-butanol at pH 9.7. The method obeys Beer’s law over a range of 1-10 ppm. The molar absorptivity is 4.9312×105 L mol-1cm-1 and Sandell’s sensitivity is 0.02083 µg cm2

. The propose method is very sensitive and selective. This method applied to synthetic and

commercial samples[3].Extraction of Cd2+, Ni2+, Pb2+, and Zn2+ from environmental waste using n-benzoyl-n-phenyl hydroxylamine (BPA). Study the effects of solvents, pH, stripping agents, extraction time, and interference of other ions on the recoveries. These metals can be quantitatively extracted between the pH 6.5-10. 1M HNO3, 4M HNO3, 1M HCl, and 5M HNO3 can be used as stripping agents to achieve the maximum percentage recovery of Cd2+, Ni2+, Pb2+, and Zn2+, respectively [4]. Extraction of micro amount Coper (II) and Nickel(II)by organic reagent2-[(3-Acyl methyl phenyl)azo]-4,5-di phenyl imidazole(3-AMePADPI) and spectophotometric determination of Copper (II) and Nickel(II) used for in different samples, studies conditions for complex formation was pH= 8 and 11 , shaking time 15 minutes for Cu+2 and Ni+2 respectively[5].

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015 Experimental Apparatus A biochrom double beam UV-Vis Spectrophotometer model (biochrom libra S60) (A Harvard Bio science company, Cambridge UK). Working at wave length 350-1100nm spectral bond width 2nm .Equipped with 10mm path length cell holder in sample and reference positions. pH measurement carried out by pH –meter , WTW CE ,E163694, (Germany), Melting point measured by Stuart Scientific COLTD,220-240(Britain). As well as for studied the structure of organic reagent prepared used FT-IR 8400 S(CE), Shimadzu corporation. Element analysis carried out by Micro analytical unit, 1108 C.H.N elemental analysis. Reagents Materials and Solutions All chemical materials received from commercial sources with high purity and used as received stock solution of cerium (II)1 mg/mL was prepared by dissolved 0.309 g of Ce(NO3)3.6H2O in 9mL distilled water contain 1 mL of conc. HNO3 and dilute to 100mL with distilled in a volumetric flask, 1×10-2M (AMBN)in Chloroform prepared by dissolving 0.410 from (AMBN)in 100ml of CHCl3, 8-Hydroxyquinoline(1%)prepared by dissolved 1gm in 100mL ethanol,1% phenolphthalein solution in ethanol this solution prepared by dissolve 1gm from phenolphthalein in 100mL ethanol by using volumetric flask, ammonia (1+1) [6]. Synthesis of organic reagent The organic reagents was prepared according to the procedure published elsewhere

[7]

dissolving (2.5g0.01mole) of 4-amino-N-(5-methylisoxazol-3-yl) benezensulfo- amide. in a solution of 4 mL concentrated HCl and 25 mL distilled water. After cooling this solution to 0 °C, 0.7 g of sodium nitrite dissolved in 10 mL distilled water was added with maintaining the temperature at 0°C. The mixture was set aside for 15 min to complete diazotization reaction. Thereafter, the diazonium solution was added drop by drop into a solution of (1.44 g, 0.01 mole) of 1-Naphthol and 1.2 g sodium hydroxide dissolved in 150 mL ethyl alcohol with keeping temperature at 0°C. After complete addition, the content was left for two hours, then 150 mL of cooled distilled water and control the pH of solution at 6 with HCl, a brown powder product was precipitated after left for 24 h. The brown precipitate was filtered off, washed with cold water, crystallized twice from hot absolute ethanol and dried over CaCl 2 to give yield of 79%, Mp (147-148˚C) and chemical formula of C20N4O4H16S with Mw. ( 408.4

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015 g mol-1) .The azo reagent synthesized in this work were identified by UV – Vis. FTIR and C.H.N elemental analysis. This reagent does not dissolved in water, but it dissolves in organic solvent such ethanol, chloroform, Acetone, DMF etc. The UV-Vis. spectrum and IR spectrum as well as the results obtained by C.H.N. study in Figures 1,2 and Table 1 demonstrate the structure of azo ligand prepared.

Fig. 1: UV-Vis. spectrum of organic reagent 4-[ N-(5-methyl isoxazol-3yl) benzene sulfoamide azo]-1-naphthol

Fig. 2: IR-spectrum of organic reagent 4-[N-(5-methyl isoxazol-3yl) benzene sulfoamide azo]-1-naphthol

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015 Table 1: Spectral data of the organic reagent[8,9] a\ UV-Visible spectral peaks (nm). peaks(nm) Assignments 250 π-π* very small sensitive absorption. 285 π-π* middle sensitive absorption. 449 n-π* visible region high sensitive absorption. b\ IR spectral bands (cm-1) Bands (cm-1) Assignments p e olic H stretching and 3399.12-602.11 bending 3062.06 aromatioc CH stretching 1624.12-1404.22 C=N stretching and bending 1467.09 for -N=N1303.92-1153.47 for, S=O 701.72 for rings of naphtol 1513.74 C=C stretching 3297.99 N-H stretching c / C.H.N.S Element Theoretical results Experimental results %C 58.81 58.63 %H 3.95 3.91 %N 13.72 13.68 %S 7.85 7.75

Fig. 3: Calibration curve of Ce3+ by 8-Hydroxyquinoline method.

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015 General Procedure For extraction experiments have to take (5 mL) of aqueous phase contain exact quantity of Ce+3 ions at optimum pH, and then adding (5 mL) of organic phase contain exact concentration of organic reagent dissolved in organic solvent, afterward shaken the two phases at optimum time, after complete shaking separate the two layers and determine the Ce+3 ions remainder in aqueous phase by spectrophotometric method

[6]

which involved for

(5 mL) aqueous solution then add 1 mL of oxine solution,1 drop of 1% phenolphthalein solution in ethanol, and ammonia (1+1) until the solution is became rose coloured. Add 1 mL of ammonia (1+1) (the pH should be within 9.9-10.6) and transfer the solution to a separating funnel. Shake the solution with 2 portions of CHC13 (5 min shaking with each portion). Dilute the combined extracts with chloroform to 25 mL in a standard flask, as well as measure the absorbance of organic phase at λmax against organic reagent as blank. The concentration of residual Ce+3 ions in aqueous phase was determined from regression line of calibration curve of Ce+3 in Figure 3 as well as the concentration of the extracted Ce+3 determined by subtraction remainder quantity from origin quantity in aqueous solution .Of stripping method for determination transferred quantity of Ce3+ to organic phase include shaking organic phase with three portion of 5mL 1:1 concentrated HCl and determined the stripped Cerium (III) by 8-Hydroxyquinoline spectrophotometric method . the experiments show the transferred quantity of Ce3+ determined by Stripping equal to the same quantity determined by subtraction ,then used subtraction method to determine transfered quantity became easy and faster Results and Discussion Absorption UV–Vis spectrum Absorption UV–Vis spectrum in Figure 4 shows maximum absorption for ion pair complex extracted at λmax= 507nm

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015

Fig. 4:absorption UV–Vis spectrum for ion pair complex Effect of acidic function Extracted 100µg Ce3+ (1.5x10-4M) in 5mL aqueous phase with 5ml of (1×10-4M) organic reagent solution (AMBN) dissolved in chloroform at different pH of aqueous phase (6-12) and shaking the two phases for (10 minutes) after that separate the two phases and determination of distribution ratio (D) as in the general method, as well as determine absorbance of organic phase against organic reagent as blank. The result as in Figures 5, 6.

Fig. 5:D=f(pH)

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015

Fig. 6: Effect of pH on complex formation as extraction The results shows optimum pH for extraction was pH=9 at the pH obtained higher Absorbance and D- value that is measure reached higher extraction .Efficiency at this pH and at pH less than pH=9 lour suitable to reach favorable thermodynamic equilibrium for extraction and by decrease pH value increase hydration shell of Ce3+ as well as increase protonated of complexing agent and decrease complexation, but at pH value more than optimum value also lead to decrease extraction efficiency Effect of Metal ion concentration Extraction of different concentrations of Ce3+ ions(1-130) µg in(5ml) aqueous solution at(pH=9) by(5ml) of (1x10-4 M of AMBN) dissolved in chloroform , shaking the two layers for suitable time, and separate the two layers and determine the remainder quantity of Ce+3 ion in aqueous phase by followed spectrophotometric method [6], and calculation distribution ratio (D) as well as determine absorbance of organic phase at λmax=507nm against organic reagent as blank. The result was as in Figures 7,8.

Fig. 7: Effect of Ce3+ concentration on activity of extraction and D value

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015

Fig. 8: Effect of Ce3+ concentration on thermodynamic equilibrium for complex formation and extraction According to thermodynamic equilibrium for complexation reaction: Ce3+aq+ (AMBN)org +2NO3-aq ↔ [Ce(AMBN) ] +2;( NO3-)2 org The results show 100µg Ce3+/5mL was the optimum concentration giving higher efficiency of extraction because effect to increase rate of forward direction of thermodynamic equilibrium that is mean increase formation and extraction of ion pair complex concentration of Ce3+ less than optimum value not enough to reach favorable thermodynamic equilibrium that is mean decrease in ion association complex formation and extraction so that Absorbance and D-value from other hand any concentration of Ce3+ more than optimum value effect to decline extraction efficiency and decrease absorbance and D-value because effect to increase rate of back ward direction of thermodynamic equilibrium according to the Le Chatelier principle and mass action law. Effect of shaking time For the kinetic side of the extraction methods are carried out by studying the effect of shaking time on the extraction activity and distribution ratio values. After extracted 100µg Ce+3 ions in 5ml aqueous phase at (pH=9) by 5ml of (1×10-4 M) organic reagent (AMBN) dissolved in chloroform by different shaking time, the results of this study in Figure 9,10 demonstrate the optimum shaking time of two layers was (10min.) to reach the equilibria of extraction and at this time obtain the maximum distribution ratio value (D), and Absorbance at 507nm shaking time but less than optimum no allow to reached the equilibria of extraction, so that she shaking time more than optimum favorite the dissociation equilibria and minimize the distribution ratio(D)and absorbance.

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015

Fig. 9:D=f(shaking times)

Fig. 10: shaking time effect on complex formation and extraction Effect of organic solvent: According to solvent extraction method which is depends on the organic solvent used in extraction method. Extracted 100μg Ce3+ ions from 5mL aqueous phase by 5mL (1×10-4 M) organic reagent (AMBN) dissolved in different organic solvent differ in dielectric constant after shaking the two phase for 10mintes ,so separate organic phase from aqueous phase determine D-value according to the procedure detailed in the general method the results was as in the Table 2 .the results show there not any linear relation between Distribution ratio and Dielectric constant of organic solution ,that is mine there is not effect for polarity of organic solvent on extraction activity but there in un effect for organic solvent structure this result reflect participation organic solvent in complex formation . Thermodynamic parameter for extraction in different organic solvent include transfere free energy ΔGt and association constant kA as well as extraction constant kex and free energy of extraction ΔGex by application relation s below The results in Table 2 showed free energy of transition ΔGt for Ce3+ ions from aqueous phase to organic phase increase with dielectric constant of organic solvents decrease but kex and ΔGex showed the high value by using Chloroform organic solvent which demonstrate 65

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015 sharing organic solvent and increase the stability of ion pair complex extracted and increase the approach between the cation and anion association complex extraction which is contact ion pair or loose ion pair. Table 2: Organic solvent effect on the extraction of Ce3+ions and ΔGt , kA , kex , ΔGex D

-ΔGt

KAx104

Kexx108

-ΔGex

35.74

Abs. at λmax=507 0.164

4.88

0.025

4.1

17.026

53.24

Organic Solvents

Nitro benzene Amyl alcohol

15.8

0.138

1.56

0.084

1.8

1.747

48.09

1,2-Dichloro ethane

10.65

0.171

5.99

85.7

0.135

4.9

19.71

53.57

Dichloro methane

9.08

0.144

1.63

0.163

1.85

1.901

48.28

Chlorobenzene

5.708

0.129

0.85

0.271

1.31

0.518

45.35

Bromo benzene

5.4

0.157

2.84

0.288

2.7

4.875

50.41

Chloroform

4.806

0.199

14.38

93.5

0.326

10.8

129.619

57.83

Benzene

2.804

0.16

3.54

0.574

3.2

7.362

51.34

Toluene

2.438

0.176

7.33

0.664

5.84

29.66

54.49

Carbone tetrachloride

2.38

0.183

7.69

88.5

0.680

6.1

35.37

54.89

Stoichiometry By using for spectrophotometric methods to know the more probable structure of complex extracted into layer which are slope analysis, mole ratio, continuous variation method, slope ratio. The results are as in Figures 9–12.

Fig. 9: Slope analysis method

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015

Fig. 10-a: Slope ratio method change organic reagent concentration

Fig. 10-b: Slope ratio method change metal ion concentration

Fig. 11: Mole ratio Method

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015

Fig. 12: Job Method All these methods show the more probable structure of complex extracted was 1:1 Ce+3 : (AMBN)

Temperature Effect Extraction of 100 μg Ce3+ ion from aqueous phase at (pH = 9) by 5mL of (1×10-4 M) (AMBN) dissolved in chloroform in different temperature after shaking the two layer for 10mintes and separate organic phase from the aqueous phase and calculate distribution ratio D at each temperature according to the procedure detailled in the general method .afterward determined extraction constant Kex by application the relation below

The results was as in Figures 13,14.

Fig. 13:Kex=f(T K)

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015

Fig. 14:D=F(TK) The results show the complexation reaction and extraction thermodynamic was exothermic behavior the thermodynamic data of extraction Ce3+ ions was ΔHex = -0.122 kJ.mol-1, ΔGex = -51.41 kJ.mol-1 and ΔSex = 172.103 Jk-1.mol-1 Synergism effect Extracted (100µg)Ce+3 according to solvent extraction using of organic reagent (AMBN) at (pH =9) and in presence different concentration of tributyl phosphate (TBP) or Methyl isobutyl ketone (MIBK) by 5mL organic solution of (AMBN) dissolved in chloroform at (1x10-4M ) concentration after separation organic phase from aqueous phase determine the absorbance of organic phase ,as well as calculate distribution ratio D at each concentration of (TBP) or (MIBK),according to 8-Hydroxyquinoline spectrophotometric method[9] detailled in general method the results was as in Figures 15,16.

Fig. 15: synergism effect with TBP

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015

Fig. 16: synergism effect with MIBK The results from the slope values demonstrate there is one molecule of TBP or MIBK participate in the complex structure extracted [Ce3+( AMBN-)(TBP)]2+;NO3- or [Ce3+( AMBN-)(MIBK)]2+;NO3-

from other hand the participation of TBP or MIBK get

enhancement in distribution ratio (D) which is replace molecule of water with TBP or MIBK coordinate to the coordination shell of metal ion to increase the partition of complex to the organic phase and increase distribution ratio (D). Methanol effect Extraction metal cations from 5ml aqueous solution by 5ml organic reagent solution at (1×10-4 M) dissolved in chloroform in presence different percentage of methanol and after separation organic phase from aqueous phase and determination distribution ratio(D),then plot log D and absorbance against methanol % get graphs in Figures 17,18.

Fig. 17:D=f(CH3OH%)

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015

Fig. 18: Abs.=f(CH3OH%) The result shows existence of methanol in aqueous phase effect to rising extraction efficiency by reason of destroyed hydration shell of Ce(III) ions and perform free and increase the chance of binding metal ion with organic reagent AMBN ,as well as the results show extraction efficiency increased with increasing percentage method until optimum percentage of methanol 60% but percentage methanol more than optimum effect to decline extraction efficiency because effect to more decrease polarity of water and in this case partitioning some of organic reagent AMBN to the aqueous phase at shaking and decrease complex formation and extraction. Effect of electrolyte salts Extraction Ce+3 ion from 5ml aqueous solution by 5mL of (1x10-4M)AMBN dissolved in chloroform at optimum condition and in presence 0.1M some electrolyte according to general method previously detailed and determined Absorbance of organic phase and the distribution ratio D the results was as in Table 3. Table 3: effect of electrolyte salts on extraction efficiency of Ce(III) Electrolyte Salts Absorbance at λ=507 nm D LiCl 0.436 25.3 NaCl 0.385 24.6 KCl 0.321 21.2 NH4Cl 0.203 18.2 MgCl2 0.282 21.7 CaCl2 0.276 19 SrCl2 0.205 16.2 The results show all electrolytes used giving enhancement in extraction efficiency , and this rising in extraction efficiency charge of a function for ionic diameter of electrolyte cation whereas smallest ionic diameter giving highest extraction efficiency because with drawing

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015 more water molecules for it hydration shell and destroy the hidration shell of Ce(III) , then Li+ giving highest rising extraction and other having larger cation giving less rising extraction Effect of interferences Extracted Ce+3 at optimum condition at according to general method detailled in presence some cations interferences and determined Absorbance of organic phase and the distribution ratio D the results was as in Table 4. Table 4: interference effect on extraction efficiency Interferences CuCl2 CoCl2 NiCl2 HgCl2 MnCl2 AgNO3 Pb(NO3)2

Absorbance at λ=507nm 0.024 0.041 0.05 0.067 0.098 0.037 0.034

D 0.72 0.78 1.27 1.94 4.26 4 0.75

The results show all cations giving interference with Ce(III) but in different iffinity with organic reagent AMBN this belongs to behaviour and nature metal cation as well as nead different optimum condition for complex formation Spectrophotometric Determination Solvent extraction as sensitive and selective method used for spectrophotometric determination of Ce3+ in different samples such as soil, vegetable, fruit etc. The samples digestion it have been using dry digestion method[10]. Prepared calibration curve at λmax=507nm to the determination Ce3+ in different samples. Afterward prepared sample solution according to Solvent extraction method and after separation the two layers measured the absorbance of organic phase at λmax=507nm against organic reagent solution as blank. Detection limit Sandel’s sensitivits

0.000145 mol /L 0.0101385 mg cm-2

RSD Ɛ

0.007709 % 1382.022 L mol-1cm-1

Journal of Kufa for Chemical Science Vol.(1) No. (10) ………………….November 2015

Fig. 19: Calibration curve for spectrophotometric determination of Ce3+ in different samples The application Table 5: Accumulated quantity of Ce(III) in different samples. The samples Bones Baby hair Traffic cop hair Cow meat(Beef) White meat of Chicken Fish farms Radish Onion Orange(Egypt) Pomegranate(Egypt) Banana

ppmCe+3 0.66 0.3 0.375 0.275 0.2 0.291 0.4 0.120 0.200 0.225 0.275

References 1) Lokhande, R. S., Janwadkar, S. P., Pitale, S., Kulkarni, S., & Patil, S. [2011]. Rasāyan J.Chem. 4(3), p 609612

2) Sinha, S., Sinha, M. K., and Pandey, B. D. [2014]. International Journal of Mineral Processing.127, p 7073.

3) Lokhande, R. S., Kulkarni, S., Pitale, S., Patil, S. K., and Janwadkar, S. P. [2011]. Extraction. 2(6), p 161164.

4) B Sarode, D. B Attarde, S. Srivastava, V. and ET Sillanpaa, M. [2015]. Current Analytical Chemistry. 11(1), p 36-43.

5) Shawket . K . Jawad and Ahmed .E. Hamza,[2012]. journal of al-qadisiyah for pure science 3, p 1-10 6) Z.Marczenko [1986]: Separation and spectrophotometric determination of elements.2nd Edition. Allis Horwood limited

7) S.I.Gusev , M.V.Zhvakina and I.A.Kozhevnikova ; Zh.Analit[1971] . Khim . 26, p 859. 8) Pal, S. , Misra, T.K. and Sinha , C. [2000]. Transition .Met.Chem. 5,p 333 9) Ali ,A..M, AL- Da,amy , M.., Kadhier A. .F. and Hatami R. .S .[2010]. N. J.of Chem. 37,p 66-73 10) Janghel, E. K., and Pervez, Y. [2009]. Journal of Scientific and Industrial Research, 68, p 940-944.