HPAC October 2020

CUTTING PLASTIC PIPE

LARGE-SCALE SOLAR THERMAL

HORSEPOWER AND REFRIGERATION

OCTOBER 2020

EFFICIENCY AND COMFORT THE FUTURE OF HYDRONICS

HEATING AND COLD WEATHER CONSTRUCTION KEEPING NEW FURNACES CLEAN

PLUMBING & IoT

SOLUTIONS FOR MID-MARKET BUILDINGS Follow Us On

Follow Us On

@hpacmag @hpacmag

CHEMFAX

TM

Manufacturer of Specialty Chemicals

Not All Glycols Are Created Equal

CHEM-FROST Safe For All Systems Including Aluminum and Solar

Premier Inhibitors Higher Temperature Rated Low Viscosity your local wholesaler or visit chemfax.com

your local wholesaler or visit chemfax.com

HEAT TRANSFER FLUID - INHIBITED PROPYLENE GLYCOL COMPARISON CHART Chem Frost 100% Pail Size PG Concentrate Amount Aluminum Safe Solar Safe Geothermal Safe Temperature Rating Viscosity @ 35% 60C Boiling Point @ 100% CFIA Approved

20L 95/5 YES YES YES 325F 5.5cP 417F YES

Brand R

Brand O

Brand H

Brand U

Brand D

18.9L 18.9L 20L 92/8 N/A 94/6 LIMITED TO 65C NO NO SOME NO LIMITED NO LIMITED N/A N/A 275F 250F 250F N/A N/A N/A 370F 370F 370F YES NO NO

20L 95/5 NO NO N/A 250F N/A 370F YES

18.9L 95/5 NO NO N/A 220F N/A 370F NO

TSORF-MEH TSORF-MEHC

Raw PG Grade

FOOD

INDUSTRIAL GRADE

INDUSTRIAL GRADE

INDUSTRIAL GRADE

INDUSTRIAL GRADE

INDUSTRIAL GRADE

Purity of Propylene Glycol Phosphate / Nitrate

99.94%+

N/A

98%

N/A

N/A

N/A

NONE YES

YES

YESrelaselYES ohw lacoYES l ruoy

Inhibitor Type

PDT NON-TOXIC

LEED

YES

DIPOTASSIUM PHOSPHATE

DIPOTASSIUM PHOSPHATE

moc.xDIPOTASSIUM afmehc tiDIPOTASSIUM siv ro

DIPOTASSIUM PHOSPHATE

PHOSPHATE

PHOSPHATE

aseloNO hw lacNO ol ruNO oy NO relNO moc.xafmehc tisiv ro

Based on information provided on respective manufacturers’ websites* **Subject to change**

We Create Living Spaces for Generations to Come

Adding Warmth to Every Day Viessman is one of the most prefered and trusted brands in hydronic heating solutions in Canada for 40 years. Whether your project is a new home, commercial residence, or retrofit we offer heating solutions supported with digital tools to provide peace of mind at your fingertips:

• Program, remotely monitor & control your boiler using ViCare App

• Free expert advice when you request

a heating system consultation online

• Extended 5 year parts and labour warranty for residential gas-fired condensing boilers up to 300 MBH input*

40 YEARS

IN CANADA

viessmann.ca *in Canada only

CONTENTS

OCTOBER 2020 / VOL. 94 NO. 6

28 FEATURES

14

14

28

PLUMBING IOT TECHNOLOGY AND MID-MARKET COMMERCIAL PROPERTIES Adding value to mid-size buildings by introducing connectivity, visibility and remote controls to domestic water systems.

By Adam Bartman and Avishai Moscovich

HVAC ADDRESSING TEMPORARY CONSTRUCTION HEAT There’s got to be a better way to build homes in cold weather and protect furnace systems.

By Ian McTeer

20

28 5

HPAC | OCTOBER 2020

PLUMBING MATERIAL KNOWLEDGE Identifying how differences in plastic piping materials impacts service decisions and procedures.

By Jonathan Simon

36 HYDRONICS COMFORT VS. THERMODYNAMICS Exploring new energy-efficient technologies and promoting the superior comfort of hydronic systems

By John Siegenthaler

CONTINUED ON P6 HPACMAG.COM

CONTENTS

OCTOBER 2020 / VOL. 94 NO. 6

40

54

SNOW MELT CLEARING THE WAY Understanding the options for snowmelt systems and the best application for your clients.

By Mike Miller

SOLAR THERMAL LARGE-SCALE SOLAR THERMAL SYSTEMS A review of how far we’ve come and lessons that can be applied to smaller systems.

By Robert Waters

44 BOILERS COMBI OR NON-COMBI: WHEN AND WHERE? Webinar review: Insights and ideas from industry experts on when the combination boiler makes sense in today's marketplace.

By Doug Picklyk

40

58 REFRIGERATION THE POWER OF THE HORSE Reminiscing and understanding the dynamic relationship of horsepower in refrigeration.

By Dave Demma

48 DEPARTMENTS 8 UPFRONT 10 INDUSTRY NEWS 24 PLUMBING PRODUCTS 33 HVAC PRODUCTS 48 HYDRONIC PRODUCTS 50 MECHANICAL SUPPLY NEWS 53 PEOPLE 61 THE SOURCE 61 TRAINING 62 CALENDAR

36 6

HPAC | OCTOBER 2020

HPACMAG.COM

EASY AS A, B, C, D. A B C D Hot Spot Pipe Locator ®

The Gen-Eye Hot-Spot® pipe locator makes locating easy. Its total field antenna array and on-screen icons lead you right to your target, without the long learning curve.

Whether you’re an experienced pro or a first time user, you can quickly locate inspection cameras, sondes, active power lines and utility lines with pinpoint accuracy.

The Hot Spot is the industry’s most rugged locator. It’s dust and dirt proof, water resistant and never too “delicate” to get the job done.

Call the Drain Brains® at 800-245-6200, or visit www.drainbrain.com/hotspot

MADE IN U.S.A. © 2020 General Wire Spring

< UPFRONT NEW WAYS TO WORK IT JUST SO HAPPENS MY NEXT DOOR NEIGHBOUR HAS DECIDED TO REFINISH THE BASEMENT OF HIS 90-YEAR-OLD TORONTO HOME. He's opening it up to make a large playroom his two young boys, three and five. A silver lining to me working from home during this pandemic, is it has allowed me a front-row seat to the progress of his renovation and to gain some insights into his decision making when it came to his home's mechanical system.

As part of the reno, he’s replaced an old cast-iron boiler that had been heating the main part of the two-storey brick house for decades. (He put an addition on the back about five years ago, and heats that section with a gas-fired forced-air furnace).

The new boiler he selected is a combination boiler, for both heating and domestic hot water. His contractor helped with the decision. He’s relocating the new wall-hung ‘combi’ boiler closer to the new furnace, and it’s taking up a fraction of the space of the old unit and hot water tank together, making the playroom, heated with radiant in-floor heating, that much larger.

For him, going with the combi boiler made sense and so far everything is working out fine. (As of this writing, the old concrete floor was removed, infloor piping has been laid down and the new concrete floor poured and set).

As a happy coincidence, in this issue of the magazine we are introducing the first in a new series we’re calling 30 Mechanical Minutes, and our kick-off presentation is on the topic of combination boilers, when and where they make sense in today’s market.

Our regular contributor Steve Goldie, along with hydronics industry expert Mathew Pottins, joined me online (socially distanced via the Internet) in early September, and together they discussed the merits and challenges with combi boilers (read more beginning on page 44).

This new 30 Mechanical Minutes series will run throughout 2021 and will touch on subjects in plumbing, heating/cooling and refrigeration with voices from our contributors and others in the industry.

Each session runs live online, and you’re invited to join in, listen and ask questions. Each 30-minute session will also be recorded and hosted on our website, so if you can’t join us live you can catch up later on your own time.

This pandemic has forced us all to make changes, from how we school our children, meet up with friends and run simple errands, to how we work and continue learning. We really hope our new 30 Mechanical Minutes will provide a great break in the day for you, keep you in touch with your industry and teach you a thing or two.

Keep on the look-out for the next online session. I hope you’ll join us on this journey. <>

HPAC MAGAZINE 111 Gordon Baker Road, Suite 400, Toronto, ON M2H 3R1 TEL: 416.442.5600 FAX: 416.510.5140 www.hpacmag.com

EDITOR Doug Picklyk (416) 510-5218 DPicklyk@hpacmag.com ASSOCIATE David Skene (416) 510-6884 PUBLISHER DSkene@hpacmag.com MEDIA DESIGNER Emily Sun esun@annexbusinessmedia.com ACCOUNT Kim Rossiter (416) 510-6794 COORDINATOR krossiter@hpacmag.com CIRCULATION MANAGER Urszula Grzyb (416) 442-5600 ext. 3537 ugrzyb@annexbusinessmedia.com PUBLISHER Peter Leonard (416) 510-6847 PLeonard@hpacmag.com COO Scott Jamieson sjamieson@annexbusinessmedia.com

PUBLICATIONS MAIL AGREEMENT NO. 40065710 Heating Plumbing Air Conditioning (established 1925) is published 7 times per year

by Annex Publishing & Printing Inc. HPAC Magazine is the leading Canadian business publication for the owner/manager of mechanical contracting businesses and their supply partners.

ISSN: 0017-9418 (Print) ISSN 2371-8536 (Online) Contents Copyright © 2020 by Annex Publishing & Printing Inc. may not be reprinted without permission.

SUBSCRIBER SERVICES: To subscribe, renew your subscription or to change your address or information please visit us at www.hpacmag.com.

Subscription Price per year: $44.00 (plus tax) CDN; Outside Canada per year: $112.00 US; Elsewhere: 1 year $123.00 (CDN); Single copy Canada: $5.00 CDN. Heating Plumbing Air Conditioning is published 7 times per year except for occasional combined, expanded or premium issues, which count as two subscription issues.

MAIL PREFERENCES: From time to time we make our subscription list available to select companies and organizations whose product or service may interest you. If you do not wish your contact information to be made available, please contact us via one of the following methods: Tel: 416-442-5600 ext. 3552, Fax: 416-510-6875 or 416442-2191; E-mail: blao@annexbusinessmedia.com; or by mail: 111 Gordon Baker Rd., Suite 400, Toronto ON M2H 3R1 Annex Privacy Officer Privacy@annexbusinessmedia.com Tel: 800-668-2374 HPAC Magazine receives unsolicited materials (including letters to the editor, press releases, promotional items and images) from time to time. HPAC Magazine, its affiliates and assignees may use, reproduce, publish, re-publish, distribute, store and archive such unsolicited submissions in whole or in part in any form or medium whatsoever, without compensation of any sort.

NOTICE: HPAC Magazine, Annex Publishing & Printing Inc., their staff, officers, directors and shareholders (hence known as the “Publisher”) assume no liability, obligations, or responsibility for claims arising from advertised products. The Publisher also reserves the right to limit liability for editorial errors, omissions and oversights to a printed correction in a subsequent issue. HPAC Magazine’s editorial is written for management level mechanical industry personnel who have documented training in the mechanical fields in which they work. Manufacturers’ printed instructions, datasheets and notices always take precedence to published editorial statements.

– Doug Picklyk, Editor Proud member of:

8

HPAC | OCTOBER 2020

HPACMAG.COM

THE CHOICE IS SIMPLE ENDLESS HEAT & HOT WATER

Only 5 Moving Parts The New SUPERFLOW Condensing Instantaneous Water Heaters & Combiâ&#x20AC;&#x2122;s.

European design meets Canadian serviceability.

Discover more at ibcboiler.com

NEWS FEATURE SEE THE LATEST NEWS @ HPACMAG.COM

Rendering of the Fieldhouse development.

10

HPAC | OCTOBER 2020

CIPHEX VIRTUAL With the physical in-person CIPHEX West 2020 trade show being moved to 2021 in Vancouver, the Canadian Institute of Plumbing and Heating (CIPH) will be presenting a virtual trade show throughout the month of November, CIPHEX VIRTUAL. The purpose of the virtual exhibition is to provide a showcase for products and 21 exhibiting companies will also present educational webinars throughout the four weeks of the event.

While exhibitor virtual booths will be accessible 24/7 for four weeks, there will also be three “live” days covering four-hour periods where visitors and exhibitors can live chat, video chat or email “live”. The three live Thursday sessions are: November 5, 10 a.m. – 2 p.m.; November 12, 5 p.m. – 9 p.m.; and November 19, 8 a.m. – 12 (noon, all eastern times). Registration for attendees is free, but there will be a $10 charge for webinars. ciph.com

NEW STANDARD FOR LEAD LEACHING IN PLUMBING PRODUCTS NSF International, the global public health organization that facilitates standards development, and tests and certifies products, has published changes to NSF/ANSI/CAN 61, the drinking water product standard required in Canada and the U.S., to further restrict the amount of lead that can leach from plumbing products.

The new pass/fail criteria for certification to the standard will require the maximum amount of lead leaching to be

reduced from 5 micrograms (µg) to 1 µg for plumbing endpoint devices such as faucets, and from 3 µg to 0.5 µg for other plumbing components such as connector hoses and small shut-off valves.

In-line mechanical devices and other product categories under NSF/ANSI/ CAN 61 are not subject to the new requirements.

Under the new standard, certification of applicable products to the lead leaching criteria is optional for the next three years to allow time to comply. On Jan. 1, 2024, all products will be required to meet the new requirements.

Revisions to the standard were approved by the Council of Public Health Consultants and ratified by the American National Standards Institute (ANSI) and the Standards Council of Canada (SCC). nsf.org HPACMAG.COM

THE DANIELS CORP.(TOP)/ADOBE

NEW FOSSIL-FUEL-FREE DEVELOPMENT PLANNED IN TORONTO Canadian developer of low-rise and condominium housing communities, The Daniels Corp., has announced the launch of its Field House EcoUrban Towns development, in Toronto. The townhome community is placing a focus on energy efficiency and low carbon emissions.

Now under construction, the project features 24, three-storey townhomes, ranging in size from just over 1,319 sq. ft. to just over 1,700 sq. ft. with prices starting at $1.1 million.

Once constructed and occupied, the townhomes are projected to use 52% less energy, emit 89% fewer greenhouse gases and reduce energy costs by 11% when compared to Daniels’ traditional townhouses.

According to Adam Molson, director of project implementation at Daniels, each unit will have ducted forced air heating and cooling via in-suite air handling units. And every unit has its own individual heat pump with dedicated compressor (which is located in the underground parking garage, rather than outside).

And for domestic hot water: “Each unit has an electric hot water tank with a conventional heating element (not heat pump). To increase the efficiency and hot water performance we have tied each hot water tank to a dedicated drain water heat recovery unit connected to the shower drains,” says Molson.

Featured elements include: Electric high-efficiency heat pumps–

providing 300 to 360% efficiency.

PowerPipe drain water heat recovery– recovering energy from warm shower water to preheat water coming into the water heater and reducing energy consumption (40-gallon electric hot water tank) Reversomatic energy recovery ventilators (ERVs)–set to reduce energy consumption and utility costs through the recovery of energy from exhaust air.

High performance building envelopes providing insulated walls to help reduce energy consumption and utility costs.

Low flow faucets and single flush low consumption toilets “Smart Meter” technology and efficient appliances–including a heat pump dryer which uses approximately half the energy of alternative options.

The EcoUrban townhomes efficiency will also be supported by 18% of the development’s energy needs being supplied by the Bifacial solar panels integrated into the solar trellis above its rooftop terraces. fieldhousetowns.com

CIPH AND HRAI HOSTING ECONOMIC OUTLOOK WEBINAR The Canadian Institute of Plumbing and Heating Peter Norman (CIPH) and the Heating, Refrigeration and Air Conditioning Institute of Canada (HRAI) are once again joining forces to present a complimentary economic forecast webinar featuring Peter Norman, chief economist at Altus Group.

The webinar, to be held on Wednesday, November 25 at 1:30 pm (eastern time), is entitled “What a Year It’s Been: What a Year Ahead!”, and it will cover many familiar economic touch points including: The economy, housing market and construction sector: 2020 pre- and post-COVID and what could possibly lie ahead?

Outlook for residential and commercial and construction through 2021.

Outlook for renovation spending with implications on plumbing and heating dollars.

Residential construction: Will the pandemic change what and where homebuyers will buy?

Commercial sector: Expect newbuilds to shift to CAPEX as changes in workplace needs dominate.

Findings from Altus Economics research including results from the Altus Home Buyer Intentions Index.

Government sector investments: will infrastructure investment be part of a COVID economic recovery plan?

This update webinar follows Norman’s presentation from May 13th when he predicted the Canadian economy was likely headed for three straight quarters of decline before bouncing back in 2021.

Norman also acknowledged at that time that this is “not a regular recession” and he anticipated that some segments of the market would rebound quickly.

Registration is required for the November webinar. ciph.com hrai.ca HPACMAG.COM

ISH 2021 DIGITAL Organizers of the ISH show, the largest international trade show for the plumbing and HVAC industries that was originally planned for March 22-26, 2021 in Frankfurt, Germany will now become an entirely virtual event.

The range of digital features on offer will include exhibitor presentations (products, information, videos, personal contacts, chat functions and one-to-one video calls), along with live streams and on-demand broadcasts of the supporting program.

All of the material will be available 24/7 throughout the event, worldwide and in every time zone. ish.messefrankfurt.com

AHR EXPO POSTPONED As of press time, the management team of the AHR Expo sent out a notice that the originally-planned AHR 2021 show dates of January 25-27 in Chicago have been officially postponed.

Results from a recent AHR Expo survey to gauge industry interest in moving the 2021 show from January to March revealed that the proposed date change was preferred by nearly 80% of exhibitor and attendee participants.

That led to the decision to possibly still host a live event March 15-17 in Chicago.

A final decision regarding the in-person hosting of the 2021 AHR Expo is anticipated by mid-October.

AHRExpo.com Continued on p12

THE EASY WAY TO BOOST PRODUCTIVITY.

Adrian Steel’s Grip Lock and Drop Down Ladder Racks are designed with ergonomics and user safety in mind. Whether you’re upfitting a single van or an entire fleet, Adrian Steel has just what you need.

Increased efficiency starts now.

AdrianSteel.com

© Adrian Steel Company 2019, all rights reserved. Adrian Steel Company is an independent equipment manufacturer, prices may vary. Please visit AdrianSteel.com to contact your local distributor for further details.

OCTOBER 2020 | HPAC

11

INDUSTRY NEWS SEE THE LATEST NEWS @ HPACMAG.COM

THE BUILDINGS SHOW GOES VIRTUAL Due to ongoing uncertainties because of the COVID-19 pandemic, The Buildings Show, which was scheduled to run in Toronto from December 2 -4, and BUILDEX Alberta, set for Calgary November 4-5, are being combined into a single national digital platform that is being called Buildings Week.

Running from November 30 through December 4, Buildings Week will be a virtual event comprised of exhibits and conference sessions associated with The Buildings Show | Construct Canada, PM Expo, HomeBuilder & Renovator Expo, World of Concrete Toronto Pavilion and BUILDEX Alberta.

Online registration for the virtual event will be free for industry trade professionals. There will be an early bird deadline for discounted educational programming which is set to expire Friday, November 13. thebuildingsshow.com YUKON OFFERING HEAT PUMP REBATES AND PILOT PROJECT TRIALS The Yukon government announced its Good Energy rebates for heat pumps, whereby homeowners can receive rebates covering 40% of project costs, up to a maximum of $8,000 for a new air or ground source heat pump.

In addition to its expanded rebate, the Government of Yukon is seeking participants for a heat pump pilot project. In partnership with electrical utilities, the project will support the installation of 25 heat pumps for both commercial and residential buildings that already have certain heating systems installed.

The pilot project seeks to understand how heat pump technology and existing heating systems interact to optimize performance for homes and the electrical grid. The Government of Yukon will cover installation costs of up to 40% up to a maximum of $10,000. yukon.ca 12

HPAC | OCTOBER 2020

ORAC HOSTING WOMEN IN HVAC/R VIRTUAL EVENT The Ontario Refrigeration and Air Conditioning Contractors Association (ORAC) is hosting a virtual two-day Women’s Day event in entitled: Women Empowering Women in HVAC/R. Taking place Wednesday, October 21 and Thursday, October 22, each day begins at 9:00 a.m. and ends before 1:00 p.m. (eastern time).

A ‘digital ticket’ costs $24.99 and provides access to the event featuring speaker sessions, contests, and giveaways along with networking opportunities.

The ticket also includes access to a post-event recording.

Early registration is encouraged. orac.ca

NEW PRESIDENT FOR ROTO-ROOTER Roto-Rooter Services, the plumbing and drain cleaning company with over 400 franchise territories serving approximately 91% of the U.S. and 40% of the Canadian population, has announced that Robert Goldschmidt has been named president, succeeding Rick Arquilla, who is retiring after 21 years in the position.

Goldschmidt has been a member of the executive team at Cincinnati-based Roto-Rooter for 28 years. Arquilla will stay on until his retirement at the end of 2020. During his time at the helm, RotoRooter’s annual sales grew from US$280 million to US$700 million while operating profit grew from US$38 million to US$150 million. rotorooter.com

RESCON LAUNCHES ANTI-RACISM CAMPAIGN The Residential Construction Council of Ontario (RESCON) has launched a campaign to bring employers, unions and government together to combat and address racism in the industry.

RESCON kicked-off a Construction Against Racism Everywhere (CARE) campaign, using hashtag #RESCONCare.

Stickers are being distributed to construction employers and the broader industry for workers to post on their hard hats and around construction sites.

RESCON and its board of directors are also spearheading the formation of a coalition of employers, unions and subtrades from all sectors of the industry. rescon.com HPACMAG.COM

Navien... making the world more comfortable every day with advanced high efficiency heating technology Navien has the right boiler options for both residential and commercial applications

NFB

Condensing Fire Tube Boilers

Thereâ&#x20AC;&#x2122;s never been a better time to upgrade to Navienâ&#x20AC;&#x2122;s highly engineered condensing wall-hung boilers.

For product details and rebate offers visit NavienInc.com

NFB-C

Commercial Fire Tube Boilers

NHB

NFC

Condensing Fire Tube Combi-boilers

Condensing Boilers

NCB-E

Condensing Combi-boilers

Earn more for each boiler at NavienRewards.com

T h e

l e a d e r

i n

c o n d e n s i n g

t e c h n o l o g y

Sept. 1 - Nov 30, 2020

< PLUMBING

IOT TECHNOLOGY AND MID-MARKET COMMERCIAL PROPERTIES Adding value to mid-size buildings by introducing connectivity, visibility and remote controls to domestic water systems. BY ADAM BARTMAN AND AVISHAI MOSCOVICH P.ENG.

I

n every commercial or multi-unit residential building there are three primary mechanical systems: HVAC, fire protection and plumbing. In terms of monitoring, controls and real-time performance data of these three systems, plumbing has been mostly ignored.

HVAC systems are largely controlled by a centralized system (often referred as a building automation system – BAS).

The fire protection system is connected to the local fire departments via the building fire-panel. When it comes to domestic water, we haven't really seen a widely scaled platform in which one can connect and control different aspects of the plumbing system.

THE UNDERSERVED MID-MARKET If you plot all building asset types on a spectrum, on one side we have singlefamily residential homes and on the other end we have Class A office towers.

In the past five years, with the advancements in Internet of Things (IoT) technologies, the single-family residential market has been well served by the likes of Amazon, Google and Apple with their smart home products and services.

On the other end of the spectrum, the Class A office towers typically have both the budget and the expertise to apply a building automation system control and monitoring capabilities. When you look at the middle of the spectrum, which we call the mid-market, you will find a large underserved community. The mid-market includes a variety of asset types 14

HPAC | OCTOBER 2020

such as new multi-family condos, smallmedium office buildings, schools, big box retail buildings, industrial buildings and strip malls. The commonality among all of these mid-market buildings, from a controls and monitoring perspective, is that they have no visibility or connectivity as it relates to domestic plumbing systems.

“Overall, there is lack of visibility and feedback information on the performance of domestic plumbing systems” NEEDS AND CHALLENGES Before we delve into how you can advance design standards of plumbing systems, let’s take a look at common plumbing challenges in a commercial building. For example, we're seeing buildings that are five to eight years post construction already experiencing pinholes, frequent pressure reducing valve (PRV) failures causing water hammer and temperature imbalance in suites where no one is aware these fixtures require annual service. We see shutoff valves that seize within a couple years because no one has exercised them since the building was commissioned.

If we look at the type of fixtures in a

domestic plumbing system, these are manually-operated shutoff valves, manually read meters as well as manually read, non-calibrated gauges and thermometers.

Overall, there is lack of visibility and feedback information on the performance of the domestic plumbing systems and it often causes havoc in buildings.

We can qualify the typical water related challenges a mid-market building faces and areas where connected systems can improve them into three categories: 1. improving day-to-day operations— for example, simplify the process to shutdown risers for maintenance work, 2. conserving water in areas where water rates are getting more expensive and the operational expenses on water is increasing without an apparent reason, 3. managing risk from water escape and floods.

TIMING IS IMPORTANT It is important to understand the right timing to implement IoT technology into a building. There are certain opportunities in which adding connected technology to the plumbing system makes sense and provides significant value with rapid payback.

Three opportunities for when to consider adding IoT to a plumbing system: Continued on p16 HPACMAG.COM

FLAWLESSLY DESIGNED TO MAKE EVERY INSTALLATION EASIER GROHSAFE™ 3.0 PRESSURE BALANCE VALVES

Introducing GrohSafe™ 3.0 valves, designed to accommodate every situation with: • One simplified pressure balance platform • Simple, easy installation • Enhanced features With its compact body, flat back and multiple connections options, it offers unmatched versatility on the job. Discover more at grohe.ca

ADDITIONAL CONNECTIONS

½" PEX crimp inlets

½" PEX cold expansion inlets

½" Stub-out inlets/outlets

½" PEX crimp elbow inlets

½" PEX cold expansion elbow inlets

< PLUMBING

Continued from p14

Placements for sensors and actuated valves for visibility and protection.

1. when designing a new building you have a lot of flexibility in the design elements and can apply a wide scale of new technology. With open walls and ceilings, it is easy to install and wire connected sensors and fixtures. Furthermore, very often, the labor is neutral. It's just a matter of installing an actuated valve in lieu of a manual valve, for example.

2. if you are looking to solve a specific need, for example if a building is experiencing pinholes on the recirculating header far earlier than it should, resulting in frequent water escape, leaks and floods, that is an opportune time to add connectivity to the plumbing system.

3. commercial properties have capital improvement plans which includes plumbing system upgrades. For example, replacing all of the riser valves, where it makes sense to consider installing actuated valves as the labour is already accounted for in the budget.

IoT AS A GAME CHANGER IoT technology is changing the game.

Early connected solutions for the midmarket were limited due to cost or technical capabilities, and consumer products are often not scalable for larger buildings. For example, residential systems can connect to a home’s 16

HPAC | OCTOBER 2020

¾-in. water supply pipe and communicate water usage and shutoff the main line in case of an emergency. When you need to connect 2-in. and 3-in. butterfly valves with a few pressure sensors to one platform, the consumer products come up short with limited capabilities.

On the other hand, a commercial BAS has all the technical capabilities but is very expensive. A BAS is often more associated with the HVAC system, not the domestic plumbing system, and particularly for a mid-market building, it is cost prohibitive.

An ideal IoT based water management solution for the mid-market should meet a few basic aspects and be low cost. It should be scalable with an ability to easily expand an installation from a small to a very large application, and it should be able to connect to a variety of sensors. Also, in order to understand system performance data its needs to read actual system conditions such as temperature, pressure and velocity to make informed decisions. Lastly, it needs to be easily retrofitted into existing buildings, non-invasive and easily installed by a plumber or service provider rather than a specialized technician.

TYPICAL APPLICATIONS As discussed, typical mid-market buildings don’t have access to a BAS or any type of visibility to their water systems.

In the following sections we take a look at the flow of water as it enters a typical two-zone multi-unit residential building and identify where current IoT technologies can be added to advance the plumbing designs and provide owners and operators with connectivity to their domestic water systems.

BASEMENT MECHANICAL ROOM In the basement mechanical room we typically find a revenue grade water meter allowing the local water utility company to calculate consumption and bill the property. Immediately followed by a code-required backflow prevention device, and often a strainer or a filtration system to remove fine particles from the water supply. The next system inline is a boosting pump package that supplies the cold water to the building at a particular pressure.

Using IoT technology we can add visibility into the system performance by applying sensory fixtures to the existing layout without any changes to the system layout.

Connecting the existing water meter to the cloud to record water usage and flow rate data allows the building operators to see real-time conditions remotely.

By adding real-time pressure sensors across the water filtration system, users can understand when the system is due Continued on p18 HPACMAG.COM

Make the shift from solids handling to grinder!

1 hp Grinder Pump Now get the robust performance of a grinder while operating on standard 115V or 230V circuitry.

Patented V-Slice® Cutter Technology Patent: See LibertyPumps.com/patents

800.543.2550

Liber tyPumps.com

7 0 0 0 A p p l e Tr e e Av e . • B e r g e n , N e w Yo r k 14 416 Copyright © Liberty Pumps, Inc. 2020 All rights reserved.

< PLUMBING

Continued from p16

for media replacement. Adding an actuated valve following the backflow prevention device allows for easy remote water shut-off in case of emergency.

Lastly, providing a connectivity platform for new booster pumps, which are typically equipped with VFD motors and sophisticated operation logic, but they may lack the connectivity option to alert the operator in case of a problem.

PRESSURE REDUCING VALVE AT ZONES DISTRIBUTION As we move along the domestic distribution system, water is pressurized into a high pressure system, then stepped down in the zones mechanical rooms through an arrangement that includes pressure reducing valves (PRV), circulator pump, and heat exchanger to a low-pressure delivery system to individual suites.

For example, with each zone is a group of 10 floors, we will have hot- and cold-water supply high pressure stepped down through a PRV from 200 psi to an adequate deliverable low-pressure side of 70 psi. Furthermore, on the low-pressure side we control the zone hot water conditions with a recirculating pump, a heat exchanger and a balancing valve to collect all of the hot water and put it back into the hot water supply.

Typically, this complex arrangement is left to operate with no connectivity or visibility on the system or fixture performance, however with current IoT technology there is actually a lot of value to be created for the operators and owners.

Actuated valves on the hot, cold and recirculating lines allow the operator to remotely shut down and contain a single zone in case of an emergency instead of shutting down water to the entire building. And according to AWWA every valve should be exercised on a regular basis, but it is never done. Connected valves, which are not modulating on a regular basis like in HVAC system, can be exer18

HPAC | OCTOBER 2020

Insight on zones with pressure reducing valves.

cised autonomously to ensure they operate when needed.

A pressure reducing valve is a complex fixture, requires annual service to replace the diaphragm and springs.

When annual service is not maintained, a failed PRV can cause havoc by allowing high pressure delivery into suites.

Delivery of high 200 psi pressure in a low pressure rated pipe increases the risk for ruptures, water hammers and temperature imbalance to tenants. By replacing the manual pressure gauges with a real-time connected pressure sensor, we can now understand the operation of a PRV and most importantly, send an alert to the operator in case a PRV fail and the outlet pressure increases above the design threshold.

The third IoT technology to apply would be on the domestic hot water recirculation within a zone. Traditionally, during building commissioning a circuit balancing valve is installed and set to allow design velocity in the recirculation line. Often, within a couple of years you will find that balancing valve has been moved, is not in the proper set position and there is no indication on the flow or water velocity in the system.

At the same time, the circulator pump is constantly running without any feedback on hot water demand. These unmonitored operation conditions, where

pressure, temperature and velocity often exceed manufacturer optimal working recommendations, lead to early failure of copper and PEX piping systems. With current IoT technology, by installing a connected flow meter, temperature and pressure sensors in lieu of the manual gauges, operators can maintain the recirculation flow rate at an optimal position and extend pipe life. Furthermore, cloud connected IoT applications can save energy by adding night setback sequences at low demand periods via throttling down the hot water recirculation flow to a minimum.

RISERS AND CIRCUIT BALANCING Next, letâ&#x20AC;&#x2122;s look at the hot and cold-water risers of the domestic plumbing system. The hot water risers will end at a recirculation header with a circuit balancing valve. Day-to-day operations in a multi-unit residential building often involve pluming service in suites. When a plumber shows up on site and needs to shut down water it is a cumbersome and disturbing process to shut down water for the whole building.

Applying affordable and low-cost IoT technology by replacing the traditional manual riser valves with a connected valve has a few benefits such as automated circuit balancing and riser shutdown in case of service calls.

HPACMAG.COM

As mentioned above, autonomous valve exercising ensures valves operate. In multi-unit residential buildings, toilets that malfunction and pass water often go undetected and become the main cause of water waste. Most residents are either not aware of the water passing or donâ&#x20AC;&#x2122;t complain about it. This makes the water bill a variable, uncontrollable cost. Looking at a bulk water bill does not provide specific enough information on water use and does not identify water waste. IoT technology, specifically real-time cold-water riser monitoring can provide real-time data and identify water waste.

HOT WATER MANAGEMENT Domestic hot water storage tanks often located in the boiler room will supply the hot water to suites via mixing valves.

Traditionally, both storage tanks and

mixing valves are manually set and lack any type of real-time feedback on temperature settings. Now, more than ever, in a post-COVID-19 environment, there is a need for real time monitoring of hot water temperatures to prevent Legionella and other bacteria in potable water. Adding connected temperature sensors to mixing valves and actuated valves on the hot water recirculation line allows real-time water management in mid-market buildings. In addition, cloud platforms can easily be utilized to incorporate all aspects of compliance with ASHRAE Standard 188-2018 managing the risk of Legionellosis in building domestic water systems, including testing, monitoring, control and administration.

SUMMARY In summary, the vast mid-market segment of commercial and residential prop-

Plumbing is an unpredictable business, but the quality of the pumps you install shouldnâ&#x20AC;&#x2122;t be. Generations of plumbers have trusted our hard-working, reliable pumps to get the job done right the first time.

Make a Big Impact on your next job with Little Giant.

HPACMAG.COM

erties is in need of advanced plumbing systems to deal with older infrastructure.

With control and monitoring of plumbing systems long being ignored, there is much value to add to by capturing realtime data with simple, and affordable, IoT cloud-enabled technology. <> Adam Bartman is a second-generation Red Seal Endorsed plumber from Toronto. Combining his plumbing experience and passion for technology, he co-founded reed (www.reedwater.io) to bring plumbing systems online to help landlords and service providers manage water at commercial properties.

Avishai Moscovich P.Eng. LEED AP is CMO at reed. He is an engineering graduate of Ryerson University and holds an Executive MBA from Kellogg School of Management at Northwestern University.

littlegiant.com

OCTOBER 2020 | HPAC

19

< PLUMBING

MATERIAL KNOWLEDGE Identifying how differences in plastic piping materials impacts service decisions and procedures.

BY JONATHAN SIMON

M

CHEMISTRY MATTERS In plastic piping, the chemical composition of the pipe can dictate how it performs in certain conditions. A good example of this is polybutylene, a plastic piping material used in new construction throughout North America in the 1980s.

20

HPAC | OCTOBER 2020

CREDIT: ANDREY GONCHAR/ADOBE STOCK

any service plumbers today cut their teeth on copper piping. But they are seeing less and less of it in the field with plastic piping having become commonplace in new construction over recent decades.

Rather than working on one material most of the time, today’s service plumbers may encounter copper piping in the morning, CPVC in the afternoon and PEX at the end of the day.

While the goal is the same regardless of the material—resolve existing issues and ensure the reliability of the system—these materials have distinct differences that impact how they perform in certain conditions, as well as how they are serviced. Keeping up with piping material changes can be a challenge and makes continuing education and training more important than ever.

To identify specific areas of opportunity for proactive education, our company (a supplier of CPVC pipe and fittings) tested service plumbers’ knowledge of the two main plastic plumbing materials in use today—CPVC and PEX—through an online quiz. The results uncovered some misconceptions about plastic piping materials in three key areas: cutting, fittings and diagnosing problems. Before we get into those, it’s useful to review the characteristics of the two materials.

Polybutylene proved unsuitable for residential water systems because of an inherent chemical incompatibility with chlorine. The material suffered from widespread chlorine-induced leaks and failures before it was removed from the market.

PEX is from the same polyolefin family of polymers as polybutene but is manufactured using a polyethylene base with cross-links between the polymer chains. PEX manufacturers also use chlorine inhibitors to mitigate incompatibility issues between the material and water treatment additives. Still, the material can be susceptible to chlorine degradation, particularly in aggressive water conditions. PEX is also softer and more flexible than either copper or CPVC and uses a different style of fitting than either of those two materials.

CPVC is a Chlorinated Polyvinyl Chloride. As a chlorinated material, CPVC is immune to the chlorine-related

problems that can exist in copper and PEX. CPVC is somewhat flexible when new, simplifying installation, and becomes more rigid as it ages. Rated to handle 100 psi at 180F/82C, it can be used in some applications that aren’t recommended for PEX, such as temperature and pressure relief lines, condensate drains and hot chlorinated water.

SERVICING CPVC The biggest mistake plumbers make today when servicing CPVC is in the tools they use when cutting CPVC in service. Because of this mistaken tool selection, they also underestimate CPVC’s potential service life.

Cutting: One of the most basic and important steps in working with any material is making a clean cut. Yet roughly half of the plumbers that took our quiz chose the wrong tool for cutting in-service CPVC. Because CPVC becomes more rigid as it ages, it reContinued on p22 HPACMAG.COM

< PLUMBING

Continued from p20

quires a different tool when cutting new versus aged CPVC. For new CPVC ratchet-style cutters can be used. Aged CPVC should be cut with a c-style tubing cutter, or alternately a wheel cutter or a fine-tooth saw. CPVC should never be cut with non-ratcheting pipe shears used for flexible hose and tubing.

Note, this aging process does not compromise the integrity of the pipe.

The pressure-bearing capability of CPVC actually increases with age. But the pipe becomes too rigid to cut cleanly with ratchet style cutters and cstyle cutters are recommended.

Fittings: CPVC uses a solvent weld process in which the pipe slides into the fitting, maintaining full flow through the pipe. Most plumbers are familiar with this process and understand a dauber one-half the size of the pipe diameter is best for applying an even coating of solvent cement. However, many still believe repairs that require solvent cement will take hours to cure.

That isn’t the case. Solvent cements specially formulated for repair can cut curing times from the several hours typical in new construction to as little as 15 minutes on cold water lines.

Identifying Failures: Pipe failures can often indicate problems that simply replacing the failed pipe won’t address. If you come across a CPVC pipe that has ballooned it is likely temperature or pressure related, and it’s worth investigating. CPVC has excellent pressure and temperature ratings, so the pipe would not be expected to fail under normal conditions. One thing to look for is a malfunctioning boiler or water heater that is overheating the water to above 200F/93C. This is not only a problem for the pipes; It could be dangerous to residents of the home.

Another issue identified in the quiz involved plumber education on the material integrity of aged CPVC. When asked whether aged or “brittle” CPVC 22

HPAC | OCTOBER 2020

needed to be replaced, a majority of plumbers said yes. This perception is probably due to problems they’ve encountered when using the wrong tools for service. In fact, older CPVC has excellent pressure-bearing capability and is stronger than new CPVC. Also, remember CPVC is immune to chlorine degradation that can occur in copper and PEX. Provided it was installed correctly, aged CPVC pipe can continue to perform for many years when the correct tools are used in service.

“An online quiz uncovered some misconceptions about plastic piping materials in three key areas: cutting, fittings and diagnosing problems.”

SERVICING PEX While PEX doesn’t become more rigid with age compared to CPVC, choosing the right tool for cutting remains an issue. Plumbers would also benefit from a better understanding of the effect of PEX fittings on flow rates and how to recognize signs of chlorine degradation.

Cutting: As with CPVC, a surprisingly high percentage of plumbers selected the wrong tool to cut PEX. PEX piping can be cut with ratchet cutters or scissors-style shears, but many plumbers suggested they could use c-style tubing cutters for this material. Because PEX is a soft plastic, most c-style tubing cutters will not effectively cut into PEX tubing.

Fittings: The quiz also uncovered a lack of understanding about the impact of PEX fittings on flow. Roughly half of plumbers believe ASTM F1960 expansion PEX fittings provide full flow performance. This isn’t possible be-

cause with PEX the pipe fits around the outside of the fitting, reducing the internal diameter of the pipe—even in expansion PEX systems.

Depending on the fitting used, this can reduce the internal diameter of a ½-in. pipe from 21% to 35%, which can have a noticeable impact on flow rates.

Using PEX to replace a copper or CPVC system with full flow fittings can result in unwanted pressure drop or require the use of upsized pipe to maintain system performance.

Identifying Failures: A high percentage of service plumbers who took the quiz misidentified a PEX chlorine-related failure as a failure caused by UV light. These two issues can be related in that UV light can consume the chlorine-inhibiting antioxidants added to protect the pipe from chlorine, but it doesn’t actually cause the failure. If you simply replace a failed pipe thinking the problem was UV light exposure, you could be ignoring broader water incompatibility issues within the system and end up coming back later to replace the pipe you put in.

Plumbers are sometimes reluctant to spend time on training because they would rather be serving customers. But the results from our online quiz highlight the importance of proactive training to stay up to date on newer materials.

Training that delivers essential information in a concise, understandable and accessible way can actually save time by enabling plumbers to work more efficiently and effectively. <> Jonathan Simon is the North American residential plumbing manager for Lubrizol Advanced Materials Inc., the parent company for FlowGuard Gold Pipe and Fittings. To help plumbers access training and education on servicing CPVC, FlowGuard Gold has created an online information hub specifically for service plumbers at FlowguardGold. com/ServiceSuccess.

HPACMAG.COM

WATER SOLUTIONS ALL FROM ONE SOURCE

From heating controls to mixing valves, Resideo offers a full range of Honeywell Home hydronic product solutions. Find Hydronic Zoning Panels, Pro Press Zone Valves, T6 Pro Hydronic thermostats and more — all in one location.

Our reputation is based on providing you with products to provide homeowners with solutions. Our products have proven to be must-stock standards, engineered for accuracy, safety and reliability — and easy installation.

bit.ly/HomeWaterSolutions

04-00026 | VN | 01/20

© 2020 Resideo Technologies, Inc. All rights reserved.

The Honeywell Home trademark is used under license from Honeywell International, Inc.

PLUMBING PRODUCTS

Bradley Corp has expanded its line of Express lavatory decks with two new designs: the GLX series (pictured) and TLX series. The GLX features a linear design with extra space to place belongings, while the TLX offers a streamlined trough design. The full suite of Express lavatory decks meet the demands of commercial restrooms and are made of Bradleyâ&#x20AC;&#x2122;s smooth and non-porous Terreon solid surface material. www.bradleycorp.com Moenâ&#x20AC;&#x2122;s M-CORE is a valve system that simplifies installation with an integrated mounting bracket that secures the valve directly to a brace. It offers a quicker temperature limit stop adjustment process, and the integrated test plug allows installers to flush and test the system without having to remove or install the cartridge. M-CORE mixing and transfer valves also are available in several inlet and outlet plumbing options. moen.ca

Webstone has enhanced its line of PEX E-X-P E2 tankless water heater (TWH) service valves. For applications where a higher flow rate is needed, new 1-in. hot and cold valve kits are now available. These compact, space-saving service valve TWH kits are available with a choice of either a standard brass or a lead-free pressure relief valve. www.webstonevalves.com/EXP

Goulds Water Technology has launched the GSD submersible sewage pump built to handle residential sewage systems, water transfer, heavy duty sump and dewatering applications. The pump features a cast iron design and me-

Cherne, a part of the Oatey family, has launched its residential plumbing

chanical seal for protection against sand and abrasive materials. It comes

smoke blower for fast and easy leak detection. Featuring a 5-ft. heavy-duty

with a built-in anti-siphon hole for easier pump installation and prevents air

hose that fits a 4-in. cleanout tee, the blower is lightweight and corrosion-re-

locking. The GSD Series is available in an automatic or manual, 115 volts,

sistant. It can be used indoors and its 122-cc, 3.5-HP, 4-stroke Honda engine

0.5 HP, single phase pump with 2-in. discharge. goulds.com

provides more than 700 CFM, making it fast, easy and safe. oatey.com

24

HPAC | OCTOBER 2020

HPACMAG.COM

NO W

AV AIL

AB

INCREASED

EFFICIENCY AND

PROFIT

AVAILABLE FOR

DOWNLOAD

Introducing the complete line of Building Information Modeling (BIM) objects, for the AquaRise速 Potable Water Piping System Available in all relevant BIM file formats. With easy navigation, these high quality, highly accurate and fully functional models allow for system testing and validation, and can be downloaded to your desktop or directly into your design model.

Either way, our BIM files are quick, easy family downloads that meet all applicable standards... and your expectations.

IPEX has the tools you need to design with confidence.

Visit us for the complete library of available AquaRise速 BIM files.

1-866-473-9462

|

ipexaquarise.com

POTABLE WATER PIPING SYSTEMS

AquaRise速 and the color of the AquaRise速 pipes and fittings are registered trademarks.

Distributed in Canada by IPEX Inc., Mississauga, Ontario.

LE

PLUMBING PRODUCTS

T&S Brass and Bronze Works is offering hygiene-boosting solutions for all kinds of facilities, including an update to its antimicrobial-coated faucet

Native Trails’ Trough 3019 sinks are now offered in a 30-in. size option

handles. The antimicrobial coating (available as an option on freshly re-

(previously only available in 48-in. and 36-in.). The smaller artisan-made

designed wrist-action, four-arm and lever handles) provides a barrier

trough sinks, constructed from natural jute fiber and cement, are suitable

against microorganisms like bacteria, molds, mildew and fungi. The anti-

for powder rooms and narrow single vanities. Like all of the brand’s Na-

microbial coating on T&S faucet handles is a clear finish that is finger-

tiveStone products, Trough 3019 is available in pearl, ash, slate, and

print-resistant and lasts the life of the product. www.TSBrass.com

earth finishes. www.nativetrailshome.com

HeatLink has expanded its F1960 PEX-a potable water expansion system to include large dimension sizes. 1-¼-in., 1-½-in., and 2-in. high performance polymer (HPP) fittings, no lead (Eco) brass fittings, and PEX-a expansion rings are now available. Suited for high flow water distribution applications, such as mains and risers, PEX-a Expansion Rings use the strong shape memory of PEX-a to form a watertight seal. www.heatlink.com

NIBCO has additional configurations of its lead-free 585HP (high performance) bronze ball valves with reversible handles, laser-welded con-

Bélanger, the Canadian manufacturer of faucets and plumbing supplies,

struction, triple-sealed stem, operating pressure up to 1,000 CWP and

has presented its latest nature-inspired collection, Nobua, part of its H2flo

150 SWP, and operating temperature up to 250F. New configurations in-

Luxx series which draws on the company’s 50-plus years of experience.

clude thread x press end connections for sizes ½-in. to 2-in. and hose cap

Drawing from the beauty of nature, the luxury bathroom sink faucets, bath-

and chain for sizes ½-in. and ¾-in. for solder, press, and threaded end

tub faucets and fillers, kitchen faucets and thermostatic shower kits are

connections. nibco.com/585HP

available in stainless steel and matt black. www.belangerh2o.com

26

HPAC | OCTOBER 2020

HPACMAG.COM

Qu uiick ui ck Installllll Co Coupl upliin ing ng

New Product!

Innovative Design Features

See how quick installation can be

• 1-Bolt Design Saves installation time over conventional Couplings • Integrated Wedge ensures Gasket Compression and prevents pinching

n a traditional coupling • 4x faster than • Innovative one bolt design n • Easy push on design

Quick Install Gasket Qui • Pipe Stop: Ensures the Gasket is properly located in the connection, and assists in vertical installations • Gap Seal: The Gasket design is optimized for any sort of installation • Additionally, our Quick Install Gasket design ensures Gasket-to-Pipe contact from the moment you install it

Ready for Quick Installations • Hold Open Clip keeps the Coupling primed for Installers out of the box

www.Shurjoint.ApolloValves.com customer service (905) 761-6161

< HVAC

ADDRESSING TEMPORARY CONSTRUCTION HEAT There’s got to be a better way to build homes in cold weather and protect furnace systems. BY IAN McTEER

T

he headline of an online article dated July 18, 2019 immediately captured my attention: “Why your new home may come with a dirty, used furnace” by Laura Osman of CBC news, Ottawa. Accompanying the article were several photographs of an unhappy homeowner in Morrisburg, Ont. pointing to his furnace and saying, “I opened up the front of the furnace and it just looked like a bag of flour exploded in there.”

Osman continues to explain that the practice of using furnaces meant for comfort conditioning is legal during the

Clare Hecla furnace 28

HPAC | OCTOBER 2020

construction process, and that some manufacturers say they are not receiving complaints therefore all must be well. Warranty records documenting premature failures would tell a different story; however, that vault of closely held manufacturer information will not be made public anytime soon.

SOME HISTORY I remember the days when large-scale house construction went into winter hibernation. Many in the HVAC trades were laid off in December and spent the winter doing whatever else they could. I delivered furniture at one time.

Builders deserve a great deal of credit for harnessing technologies that allowed house construction to continue through the winter providing yearround employment for those of us in the residential heating industry.

Superplasticizers and self-consolidating concrete combined with other warming techniques meant basements could be poured into the winter months.

Builders take precautions to prevent fresh pours from freezing so that compressive strength is not compromised.

Once the concrete pour had set-up enough, carpenters started framing.

Typically, propane-fired salamanders were employed to keep the foundation

warm during the framing process.

Installation of the roof sheathing meant the sheet metal rough-in including a B-vent chimney could start, followed closely thereafter by the basement duct and furnace.

Then the rush was on, get the furnace gas-piped and wired so that it could be used to keep the structure warm, even if all the windows and doors had yet to be installed.

Sometimes the basement floor, yet to be poured, required the furnace to be suspended 4-in. above the gravel using plumber’s metal strapping allowing the concreting job to be done later.

And, sometimes, the furnace was fired-up without ducting, the blower door was removed allowing heated air to simply flow out the top, that was before door interlock switches became a requirement.

The old draft hood equipped furnaces of yesteryear with their cold rolled steel heat exchangers, pilot lights, ribbon burners and belt-driven fans seemed almost indestructible back then. Starting one of the old blisters in a basement at 20F required HPACMAG.COM

Collapsed blower wheel.

PHOTO CREDIT EMPTYCLOUDS/GETTY IMAGES

some finesse, as the chimney would be so cold the flue products would start spilling into the basement until the B-vent warmed up. Condensation would also occur inside the heat exchanger; you could hear the water boiling in there. The bimetal fan control took ages to warm up enough to start the fan, then the return air was so cold the fan would cycle off seconds later.

Salamanders, when used, put some heat into the building making the furnace start-up less traumatic.

Some great Canadian-made furnaces such as the Clare Hecla (later Clare Brothers or simply Clare) model pictured to the left (not to mention, marques like McClary, Anthes, Grimbsy, Smartâ&#x20AC;&#x2122;s, Olsen, Conroy, Findlay, Goodcheer and others) all had their day in houses under construction at one time or another.

After surviving seemingly relentless clouds of drywall dust whilst heating the house under construction, unevenly loaded blower wheels would start shaking the furnace like an unbalanced washing machine causing consumer complaints.

HPACMAG.COM

Only one way to fix this problem: remove the blower, disassemble and clean the blower wheel with water, as no amount of brushing could remove drywall dust once centrifugally packed onto the blades.

Todayâ&#x20AC;&#x2122;s furnaces use direct drive centrifugal blowers, the motor is secured into the assembly using a belly band or resilient mount, both styles then bolted to the blower housing. An out-of-balance wheel will stress the mounts to the point of failure or even cause the blower wheel to collapse.

I accept the argument such failures can happen at any time during the life of a furnace or air handling unit mostly caused by lack of proper maintenance.

Yet, it is still the end users right to start off with a clean machine to abuse, or not, down the road.

SERVICE CALLS An air handling unit (AHU), such as a gas furnace, cannot function properly or deliver its advertised benefits with a filthy or damaged blower wheel. Arguably, it is one of the most important AHU maintenance items, yet the entire blower as-

Dirty blower with drywall dust.

sembly is too often exceptionally difficult to access for cleaning.

Since no one has ever developed a tool meant for cleaning centrifugal wheels in place, it is still necessary to pull the blower for disassembly and cleaning. Modern gas furnaces have slide-out blowers, decidedly an improvement over the securely bolted blowers of yesterday, however, now the service tech is faced with disconnecting things like the control board platform, condensate tubing and thermostat wiring.

Other components, not necessarily affected by dust and dirt, nevertheless suffer from the rigors of construction heat. A heavily loaded blower wheel may cause the unit to overheat thus continually cycling the limit control causing it to fail-open thereby generating a no heat service call.

Limits are safeties (not operating controls) and typically do not reset after cycling repeatedly. Gas valves and hot surface igniters will have some advertised reliability vanish, stolen by useless cycling in a dusty, damp basement. Apart from blower wheels, the Continued on p30 OCTOBER 2020 | HPAC

29

< HVAC

Continued from p29

PSC fan motors (pictured above) failed electrically, or seized mechanically, within the first year of operation.

most common premature failures related to temporary construction heat are blower motors, draft inducers, burners, and flame rods.

Low temperature rise creates unacceptable amounts of condensate especially in the primary heat exchanger.

Furnace manufacturers want a minimum return air temperature maintained, typically 55F or 13C. New construction invariably records return temperatures considerably lower promoting excess condensation in all the wrong places.

Ultimately, acidic condensate becomes further contaminated with chlorides and fluorides contained in paint, varnishes, cleaning compounds, stains and curing concrete potentially leading to rapid deterioration of the heat exchangers. Aluminized steel, thus exposed to corrosive elements, cannot be expected to stand the test of time.

INDUSTRY REACTION It’s not as if consumer complaints fall on deaf ears. Industry regulators and manufacturers have developed a standard for temporary heating that is typically included in the “Safety Section” of gas furnace installation instructions. As part of the ANSI Z21.47/CSA 2.3 standard, temporary heating is allowed if: • Furnace and vent system are complete and installed per manufacturers instruction • Furnace is controlled by a room temperature thermostat 30

HPAC | OCTOBER 2020

• Furnace return air duct must be complete and sealed to the furnace • Furnace input rate and temperature rise must be verified as per the rating plate • Furnace combustion air must come 100% from outdoors • Furnace return air temperature range is between 55°F (12.7°C) and 80°F (26.6°C) • Furnace must be supplied with an external, field supplied air filter.

• Furnace, duct work, and components must be cleaned upon substantial completion of the construction process. Furnace operation must be in accordance with manufacturer’s instructions.

While having a well-articulated standard providing rules for temporary heating helps both builders and HVAC contractors to provide excellent products to the public, unfortunately not all appear to be using the guidelines properly as noted in the recent CBC article.

Obviously, the new homeowner’s furnace had been used for temporary heat but had not been cleaned properly, if at all. Drywall dust is so insidious, cleaning a fin-tube secondary heat exchanger while lying on ones back inside the empty blower compartment is something I doubt gets done very often after construction ends.

When drywall sanding hits high gear, cleaning/changing the furnace air filter would be a daily requirement, yet, con-

Failed draft inducer from a high efficiency gas furnace loaded with drywall dust.

“Furnace air filters were never meant for construction applications.” ventional 1-in. air filters are useless against drywall dust. A MERV 11 filter would load up quickly eventually blocking airflow. Furnace air filters were never meant for construction applications. Efficient filtration would require frequent intervention by some person to change loaded filters thus maintaining airflow.

Having worked in basements with a roaring propane salamander sounding a like jet airplane on afterburner, I can understand why the trades hate them.

Somehow, the temperature of the building must be raised by other means before the furnace is started to prevent premature failures. It really means that a furnace meant for human comfort conditioning should not be started until the construction phase is substantially completed, a point in the process often called “carpet phase.”

By then, drywalling should be completed and with construction dirt and debris cleaned out of the ductwork, the furnace is ready to start its life.

Continued on p32 HPACMAG.COM

BEFORE

AFTER

BEFORE

AFTER

YOUR ONE - STOP SHOP

FOR

ENERGY- SAVING

HVAC RETROFIT

SOLUTIONS

(905) 565--1038 info@rosenbergcanada.com www.rosenbergcanada.com www.ecfangrid.ca

BEFORE

BEFORE

AFTER

AFTER

Follow us on:

< HVAC

Continued from p30

LEGISLATION? I am a classic liberal at heart, I do not believe the heavy hand of governments must regulate every function of our lives. Best practices need not carry prescriptive regulation if the group is willing to acknowledge certain instructions must be followed beforehand. Yet, best practices have been ignored too often when it comes to protecting a new homeowner’s investment.

Damaged parts, such as those I have included in this article, required a service call—a new homeowner had no heat.

The homeowner had to wait at home for the service technician, possibly missing work, a major inconvenience.

Poor performance caused by filthy heat exchangers or blower components also require a service call, sometimes by an inexperienced technician and, frustratingly enough, the issue is not always resolved to the homeowner’s satisfaction leading to more service calls.

Since a high efficiency furnace is meant to save energy, how much does the collective energy budget of a given house balloon when an abused furnace component fails? Another motor must be manufactured, delivered to a store, carried to a jobsite in a vehicle, all this extra inefficiency must be added onto that house. Energy is energy, does it matter if the fur-

Gas burners and flame rods readily corrode in the face of contaminated combustion air. Burner cross lighters become blocked with rust or debris creating either rough starts or ignition lockouts. Flame rods do require yearly maintenance but should not corrode so badly once the construction chemicals are largely gone from the structure.

Here is a much better way to provide temporary construction heat, a portable heater.

Spending more time in your garage?

Extend your fall projects into winter with the LD2 and LS2 residential tube heaters by

RE-VERBER-RAY

www.brantradiant.com 32

HPAC | OCTOBER 2020

nace is using it or the service truck burning through a tank of gasoline while the furnace is down?

One commentator to the CBC article wrote, “crying over nothing, a couple of weeks max out of 15 years. You ain’t gonna notice.” Well, dear reader, you can tell that to any of the homeowners unduly affected by no heat or poor performance from brand-new heating systems.

The article also noted that the Canadian Standards Association (CSA) has been in talks with industry groups with the goal of developing better standards and common guidelines, but nothing is expected from these discussions until 2021.

Our industry does not need any more media reports about unhappy customers. In the meantime, I would simply suggest that the best practice to prevent damage and premature failures of brand-new heating equipment is this: Don’t use it for temporary heat. <> Ian McTeer is an HVAC consultant with 35 years experience in the industry. He was most recently a field rep for Trane Canada DSO. McTeer is a refrigeration mechanic and Class 1 Gas technician.

HPACMAG.COM

Contest runs from October 9 – November 20, 2020

Enter for a chance to

WIN WITH

2020

*

The Perfect Backyard BBQ Package!

(approximate retail value $6,000 CAD)

SECONDARY PRIZES: 1 of 5 $100 CAD Gift Cards to M&M Food Market™

THE GRAND PRIZE INCLUDES:

• • • • •

Premium Brand BBQ Keter® Unity Table & Bevy Bar Patio Heater 2 Adirondack Chairs $250 CAD Barbecues Galore & $200 CAD M&M Food Market™ Gift Cards

Enter online at

ScoreWithSystem636.com or visit your local participating System 636® distributor for a ballot.

*Some restrictions may apply. See ScoreWithSystem636.com for complete Rules and Regulations.

System 636 ® is a registered trademark.

HVAC PRODUCTS

Resideo adds to its Honeywell Home non-programmable thermostat offer-

FLIR Systems TG165-X MSX thermal camera is an all-in-one diagnostics tool

ing with the new E1 Pro and T3 Pro thermostats. The E1 offers a large dis-

with a spot temperature gun and thermal imager. The camera identifies hot

play and is available in a 1H/1C model. The T3 (pictured) has a larger

spots that indicate electrical or mechanical failures, and cold spots that indi-

footprint and the same wiring plate and comes in 1H/1C and 2H/1C heat

cate water or air leaks. Built around a thermal 80 × 60 camera sensor with

pump models. Both are part of Resideo’s private label program for contrac-

4,800 pixels, a new laser-projected bullseye target aids in pinpointing areas

tors to place their information on the thermostat face. resideo.com

of concern. www.flir.com/tg165-x

The SALUS ST920WF SOLO Wi-Fi thermostat connects to 2.4GHz Wi-Fi networks and can be controlled from a phone, tablet or Alexa and Google Home devices. It has a large LCD display with touch keys and five powered relay outputs to accommodate HVAC and hydronic systems: 2 H/2 C for conventional HVAC or hydronic systems and 3 H/2 C for heat pump applications. salusinc.com

Venstar’s new programmable Wi-Fi Explorer Mini Fan Coil digital thermostats are available in residential (T2100) and commercial (T2150) models, The compact units are 3.2 x 3.2 in. and less than an inch deep. Both models feature a large display, compatibility with Venstar’s wire-

AJ Manufacturing has two new options to its

less temperature sensor, setpoint limiting and/or total

Criti-Clean Ultra HEPA filtration units in order to

keypad lockout, two- or four-pipe configurable and the

more effectively combat airborne viruses, as

commercial model includes override capability and pre-

well as bacteria, mold and other pathogens.

occupancy fan purge. www.venstar.com

The new built-in modules include ultraviolet-C (UV-C) radiation and needlepoint bipolar ionization. The fan-powered laminar flow HEPA fil-

SpeedClean’s CoilJet flexible wand with LED

ter diffuser provides a steady stream of puri-

light allows HVAC/R professionals to clean

fied air into a room and is available as a

coils in small spaces with little to no light. It

traditional ceiling-mounted unit, and a porta-

works with the company’s CoilJet coil cleaning

ble model on wheels. ajmfg.com

system, and well suited for mini split systems, air handler coils, PTAC coils, refrigeration units and hard-to-reach coils. The wand attaches using a quick-connect adapter and its 12-in. flexible design can bend or curve to reach tight spots. www.speedclean.com

34

HPAC | OCTOBER 2020

HPACMAG.COM

www.caleffi.com

HIGH PERFORMANCE DHW TEMPERATURE CONTROL

MEETS REQUIREMENTS OF CSA Z317.1

The LEGIOMIX ÂŽ family of digital mixing valves offers high performance DHW temperature control with the highest rated flow capacity in the market. The automatic self-cleaning feature ensures smooth operation and longevity. Available in a wide variety of connections with optional BAS integration. The digital interface includes data logging, alarming, and selectable automatic scheduling to thermally disinfect the system for control of Legionella bacteria. CALEFFI GUARANTEED.

< HYDRONICS

COMFORT VS. THERMODYNAMICS

Hydronic professionals need to explore new energy-efficient technologies and promote the superior comfort of hydronic systems. BY JOHN SIEGENTHALER

F

36

HPAC | OCTOBER 2020

THERE’S A DIFFERENCE Achieving and maintaining thermodynamic equilibrium within a conditioned space does not imply comfort. Even a room that maintains a stable 20C at the thermostat could have drastically different interior surface temperatures, strong drafts, a high degree of floor to ceiling temperature stratification, and millions of suspended dust particles in the air.

Still, if the space maintains a 20C air temperature at the thermostat some occupants might think the heating system’s performance is acceptable.

There are quantifiable characteristics associated with human thermal comfort. They include operative temperature, mean radiant temperature, radiant asymmetry, air temperature stratification, air velocity, relative humidity and others.

Unfortunately, most of these parameters are neither calculated as part of the system design, nor measured during comContinued on p38 HPACMAG.COM

PHOTO CREDIT KASTO/ADOBE STOCK

or decades, the basic approach to designing space heating systems has been: 1) Determine the “design” heating load of the building, (e.g., how many Btu/hr the building requires to maintain interior comfort during the coldest outside temperature); 2) Select a heat source capable of creating at least this many Btu/hr of heat output; 3) Design a distribution system that can divide up the heat output from the heat source and send the required rate of heat loss to each space within the building.

From the standpoint of thermodynamics, a building can be considered as a “control volume” — a simple hypothetical box that has heat flowing into and out of it. If the rate of heat input happens to equal the rate of heat loss, the temperature inside the control volume remains constant. This is called thermodynamic equilibrium. Any combination of building materials, dimensions, heating hardware, etc. that balances heat input with heat loss could attain a thermodynamic equilibrium.

< HYDRONICS

Continued from p36

missioning. Instead, the sole proxy for human thermal comfort during the heating season is being able to establish and maintain an air temperature in the range of 20C at the thermostat.

I call this attitude toward comfort “Btus in a box.” For many it doesn’t seem to matter how the Btus go into the “box” (e.g., living space) as long as the inflow rate equals the outflow rate.

This attitude is applied to a wide spectrum of building types and architectural paradigms. Perhaps it’s not surprising to see it in utilitarian buildings such as business rental properties, hotels or fast food. The intended function of these buildings—generating revenue—treats human thermal comfort with minimal regard. Design to satisfy the thermostat, end of story.

WHAT MATTERS? In modern North American culture, energy efficiency is often touted as having high value, something we all should aspire to. Fair enough. But achieving energy efficiency at the expense of comfort will, in the long run, fail as a business strategy.

The desire for comfort is autonomic.

We all continually seek it. The lack of comfort has physical and physcological consequences. It determines, in part, our productivity, our attitude and our physical health. The need for comfort is not something we can escape, trivialize or appease by saving money on inferior heating systems.

Space heating products that promote energy efficiency sometimes make claims of “comfort,” but seldom offer quantifiable justification.

Consider, for example, a ductless airto-air heat pump. Under standard AHRI rating conditions these heat pumps operate with impressive coefficients of performance. However, ductless air-toair heat pumps used in cold climates require periodic defrosting of their outdoor evaporator coil. During this pro38

HPAC | OCTOBER 2020

“As the world moves steadily away from using fossil fuels, electrically operated heat pumps are sure to gain market share as heat sources.” cess heat from the occupied space is sent back outside to melt frost off the coil. This causes noticeably cool air to be blown into occupied spaces.

Although the cycle may only last a few minutes, it’s unpleasant to anyone in the path of that air stream, especially on a cold winter night. Defrost can occur several times each day. How do repeated blasts of cool air into occupied spaces equate to comfort?

Even air-to-water heat pumps supplying hydronic distribution systems have to perform defrost cycles. The difference is that the required heat comes from a buffer tank, or perhaps a high thermal mass heated slab, rather than room air. The occupants will have no perception of when a defrost cycle occurs. Comfort will not be compromised.

Some advocates of ductless heat pumps also suggest that only two or three interior “high wall” cassettes are needed. The caveat is that interior doors should remain open to allow warm air to disperse throughout the house. If this constraint can’t be met, some suggest setting up small electric space heaters to keep the air temperature acceptable in rooms with closed doors. To me, that’s a major compromise in how the building can be used.

comfort of low temperature hydronic distribution systems.

Those that do will likely receive support from “allies” they may not have anticipated. Most electric utilities actively promote heat pumps. So do many governmental energy agencies, often with generous financial incentives.

Advocates for renewable energy and a low carbon future generally recognize that electricity—increasingly produced from large scale renewable sources—is the “fuel” of the future. Builders and architects specializing in low energy or net-zero buildings generally promote the use of heat pumps.

What you bring to the table is the track record of superior comfort afforded by low temperature hydronic systems. It’s up to you to tell this story to customers, architects, builders, politicians and anyone else who will listen.

They all know that efficiency is important. Few of them understand the consequences associated with stark differences in comfort between forcedair and hydronic distribution systems.

If you plan to be in the hydronics business in the coming years, you need to know how to combine heat pumps with hydronics. I’ll do my best to bring you continuing information on this winning combination. <>

EFFICIENCY + COMFORT As the world moves steadily away from using fossil fuels, electrically operated heat pumps are sure to gain market share as heat sources. This presents a major opportunity for the North American hydronics industry.

To capitalize on this trend hydronic professionals must leverage the high efficiency of air-to-water or water-towater heat pumps with the superior

John Siegenthaler, P.E., is a mechanical engineer and a licensed professional engineer. He has more than 35 years experience in designing modern hydronic heating systems. His latest book is Heating with Renewable Energy (see www.hydronicpros.com for more information).

HPACMAG.COM

ADVERTORIAL

THE ONLY TOTAL THERMAL SOLUTION TO SAFE DOMESTIC HOT WATER IN COMMERCIAL BUILDINGS Caleffi North America is the only company that offers digital temperature mixing, thermal balancing, and scald-protection valves that are designed to work together for a total system solution in providing safe DHW in commercial buildings.

The Caleffi 6000 Series LEGIOMIX® valve has the market’s highest rated flow capacity and is available in ¾" through 3” sizes to meet the domestic hot water requirements for any project big or small. In addition to highly accurate mixed water temperature control, the LEGIOMIX has integral calendar-based automatic thermal disinfection programs which can be enabled to control Legionella bacteria. The LEGIOMIX can stand alone or connect to a building automation system with Modbus or BACnet network communication with data logging capabilities.

The 116 Series ThermoSetter™ balancing valves provide state-of-the-art temperature-based balancing for the secondary piping circuits that serve fixture groups throughout the building. The valve’s temperature setting is adjustable to provide “set it and forget it” fool-proof balancing control. Models are available with a special “bypass” cartridge that opens the valve to increase flow during a thermal disinfection cycle, for those projects that are implementing Legionella control. The 116 Series valves have been used in conjunction with the LEGIOMIX valve family around the globe for over 15 years; together they have a solid history of performance and reliability.

The 5212 SinkMIxer™ scald protection valve provides final temperature control at each point-of-use to protect people from elevated water temperatures. The convenient 4-port design minimizes connection points and the potential for leakage and the high quality mounting bracket provides a clean installation and easy serviceability.

These innovative, high performance valves are precision engineered and manufactured in Italy using low lead dezincification resistant (DZR) brass and modern composite materials for maximum scale resistance and durability. They meet all applicable standards for the USA and Canada including ASSE 1017, ASSE 1070 and plumbing codes IPC, IRC, UPC and NPC. The complete system thermal control package is part of Caleffi’s continuing commitment to excellence in technical innovation. Call today to learn more! 414-238-2360

www.caleffi.com

Our LEGIOMIX meets requirements of CSA Z317.1 Special Requirement for Plumbing Installations in Canadian Health Care Facilities.

< SNOW MELT

CLEARING THE WAY Understanding the options for snowmelt systems and the best application for your clients.

BY MIKE MILLER

CONTROLS Designing an effective snow-melting system takes into consideration several factors, including Btu/sq.ft./hour load requirements, snowfall rates, snow density, snow temperature, outside temperature, wind speed, tubing size and tubing spacing. All these factors help a professional system designer and installer create a system that will be the most efficient and ef40

HPAC | OCTOBER 2020

CREDIT: ND700/ADOBE STOCK

T

he demand for snow and ice melting (SIM) systems continues to increase as property owners realize the convenience and safety benefits the systems provide. These hydronic systems are designed to remove snow and ice by circulating a heat transfer fluid through tubing installed in or below an outdoor surface (concrete, asphalt, or interlocking stone). Increasingly snowmelt applications are offering added peace of mind for property owners of every kind, especially commercial businesses, multi-unit residential properties and institutional buildings where they can reduce liability issues and improve access to facilities, which is even more relevant with our aging population where mobility issues can be a challenge.

Traditional snow-clearing methods (shovels, snowblowers and ploughs) over a long winter can result in unpredictable maintenance costs for property owners and the use of chemicals can damage hard surfaces. Hydronic SIM systems will pay for themselves over time, and setting them up correctly will only enhance that payback.

fective for the project.

When it comes to controlling the system, there are several options to choose from, including automatic, semi-automatic and manual controls.

A fully automatic system uses a sensor placed in the ground to detect when snowfall begins. The sensor sends a signal to the heat source to activate the warm liquid flow through the radiant tubing. Once the snowfall stops and the sensor is dry and clear of snow and ice, it sends a signal to stop the water flow and shut down the system.

This energy-efficient method is typically the most economical, as it runs only when needed.

The location of the snow/ice detector is very critical. It should be located in an area where it would be most likely to detect snow accumulation. The detector usually adds to the initial component cost, but it helps run the system economically. Compared to a manual or semi-automatic system, the automatic sensor addition often pays for itself within months.

A semi-automatic control requires a manual intervention to start the system, but also includes a timer that will operate for a pre-set amount of time and then shut the system off. Setting

the right amount of time is the key and often hard to predict.

A manual control is simply that—the system turns on and off with the flip of a switch. While this is the most cost-effective option to install, it generally costs more to operate, as the human interface requirement typically doesn’t align with that of perfect timing to start or stop a system. Operationally, it could quickly become very expensive to operate if disabled too late or worse yet, forgotten about until the fuel bill is in the mail.

If turned off too early, it could pose a safety threat as any water from the just melted snow could reform into ice if not completely removed. When enabled too late, the slab’s pick-up time will increase, as will the running time. This system definitely requires an attentive user.

Another option for controlling a snow-melt surface is to idle the system at a pre-set temperature (typically 22°F to 28°F) to ensure it can ramp up quickly in the event of snowfall. This option is often useful in critical areas that must remain snow- and ice-free, such as walkways or entryways to buildings to keep them safe. The idle option can be used with either automatic or semi-automatic controls.

Continued on p42 HPACMAG.COM

It works exceptionally well. I can’t believe how much hot water it makes.”

TIM BRITANNIA, BRITANNIA PLUMBING

The warranty is great.

That’s a big sales feature…especially when I tell customers I can give them a little extra.”

CHAD LIPINSKI, NEW ENGLAND GAS SYSTEMS

DISCOVER WHY MORE CONTRACTORS TRUST TRIANGLE TUBE’S INSTINCT FIRE TUBE BOILER AND THE VISIT OUR WEBSITE FOR TESTIMONIAL VIDEOS.

.

One thing about the boiler - I was able to hang it myself – that’s huge.”

MATT GOODEN, BLUESKY PLUMBING

< SNOW MELT

Continued from p40

Any of these systems should run off a slab sensor embedded in the slab for accurate surface temperature control.

Setting the right surface temperature for a melting event may change how the system performs.

For example, higher melting slab surface temperatures help clear off snow from a surface more quickly, but they are more expensive to operate as the temperature difference of slab surface temperature compared to ambient outdoor temperature is greater and therefore the load is greater.

Lower melting surface temperatures clear off snow at a slower rate, but the load of the system is decreased as the temperature difference between slab surface and outdoor air is lower.

Melting surface temperatures that I personally use for snow melting systems are typically 36F residentially and 38F commercially.

You can also operate zoned snow melting systems with multiple automatic snow/ice detectors. Zoned snow melting systems accommodate higher priority and lower priority zones, as well as different slab surfaces.

Snow melting systems should never run without a system controller that was developed and designed specifically for that purpose. The reason for this is that most controls today come with very intense algorithms to make snow melting as efficient as possible.

The system should have outdoor temperature guided capability that can override the system from entering snow melting mode if it is too warm outside and mother nature could melt the snow for free, or if the outdoor conditions are so extreme that a given heat source would not have enough capacity to get the job done.

Depending on surface covering, some snow melting systems may need to control the rate of slab surface temperature rise to avoid damage to a slab caused by tensile stresses from a cold start.

42

HPAC | OCTOBER 2020

APPLICATIONS Just like a radiant floor heating application, these systems circulate a warm water/glycol mixture through tubing.

Embedded hydronic SIM systems can be used in any exterior area, including stairs, sidewalks, driveways, parking lots, parking ramps, loading docks, building entrances, wheelchair access ramps, and even helipads on building tops. Almost any area that accumulates snow or ice can benefit from a snow-melting system.

Higher-end residential properties most often suit fully-automatic systems or a combination of fully-automatic and semi-automatic. The combination system is often used where there is a higher traffic area or zone, such as driveway and sidewalk that uses an automatic snow/ice detector, and a separate zone for a patio or deck, or around pools and hot tubs, that would only run if in use. In this case, there would be two zones, one with an automatic snow/ice detector and one with just a slab sensor and some sort of push-button device.

On the high-end residential and commercial side, properties often have multiples of fully automatic and possibly semi-automatic snow melting zones.

Fully-automatic zones may include parking lots, driveways, sidewalks and different exposures or surfaces. Lower traffic areas, such as patios or loading ramps, call for a semi-automatic system.

CHALLENGES The main challenges I hear about snowmelt systems are operating costs and the length of time it takes to clear the surface. When digging into higher operating costs, I often find that slab melt temperature setpoints are too high. The user needs to understand that the greater the surface temperature is set to, the greater the energy consumption. I typically recommend keeping a snowmelt surface temperature just above freezing (36F is a setpoint I normally run with).

Regarding the amount of time it

takes for the snow to melt. With lower melt setpoints, it will take longer to melt the slab. The question the client needs to ask is what does he/she have more of, money or patience? The differences between time versus costs need to be explained at the outset.

Idling is another discussion you would want to have with the client. If you are idling a slab, it will reduce the melting time once the snow does land, but it will also cost more to idle a slab while waiting for snow accumulation that may or may not come.

I personally do not recommend idling of snowmelt slabs for residential applications. It makes more sense in commercial applications..

If idling of a snowmelt slab is what the consumer wants, the same principle mentioned above applies. The lower the idling setpoint, the more cost effective it will end up being. I often recommend something in the neighbourhood of 29F for an idling setpoint.

Before starting a SIM system design it is very important to evaluate the customerâ&#x20AC;&#x2122;s needs and expectations.

Snow melting can be a science on its own and there are always other features, functions and benefits to evaluate.

CSA B214-16 Installation Code for Hydronic Heating Systems, chapter 17 includes snow and ice melting systems as stand-alone systems and covers several topics including: controls, freeze protection, tubing placement, spacing of tube fasteners, loop lengths, and insulation.

Whatever the application, the manufacturers and suppliers specializing in this field can assist in working through the options. <> Mike Miller is director of sales, commercial building services, Canada with Taco Inc. He can be reached at hydronicsmike@tacocomfort.com.

HPACMAG.COM

Nudura Inc. is now a proud part of

See the difference at

THE EASY INSULATION FOR RADIANT HEAT

HYDROFOAM® IS THE IDEAL RADIANT FLOOR INSULATION PRODUCT FOR RESIDENTIAL AND COMMERCIAL CONSTRUCTION PROJECTS.

The floor of a building is often the most ignored surface when it comes to insulation. The floor, when insulated with HYDROFOAM, completes the building envelope and increases comfort and energy efficiency.

HYDROFOAM maximizes radiant floor heating by ensuring the heat is dispersed evenly throughout the entire floor area, providing building occupants with a comfortable living and working environment.

HYDROFOAM Learn more at

NUDURA.COM/HYDROFOAM

tremcocpg.com

< BOILERS

COMBI BOILERS, NON-COMBI BOILERS: WHEN AND WHERE? HPAC hosts its first 30 Mechanical Minutes free webinar discussing the advantages and challenges of combination boilers in today’s marketplace. BY DOUG PICKLYK

O

n Wednesday, September 9, HPAC Magazine hosted the first of our free 30 Mechanical Minutes series of educational webinars for the mechanical industry. This first session, “Combi Boilers, Non-Combi Boilers: When and Where?”, invited two hydronic industry experts online to discuss the benefits and challenges of combination boilers, those appliances that handle both space heating and domestic hot water for home owners and other building spaces.

The online session featured a dialogue between regular HPAC contributor, Steve Goldie, hydronics specialist with Next Supply, and Mathew Pottins, group leader for residential products with Aqua-Tech Canada. Goldie and Pottins tapped on their years of experience in the field and shared photos of past installations to highlight the evolution of combi boiler technologies and how the products are being used today.

Both speakers noted that combination boilers are very much in demand in our Canadian marketplace. Creating one appliance for both heating and domestic hot water (DHW) has led to different designs over the years. Goldie shared a photo of an older storagebased combi system where an enclosed hot water tank stored energy and put that through the heat exchanger to do the closed loop space heating.

“One of the things that makes a combi system very desirable is they don't take up a lot of space,” said Goldie.

Pottins compared the shrinking size 44

HPAC | OCTOBER 2020

Webinar participants (top to bottom): Mathew Pottins, Doug Picklyk and Steve Goldie. Here, Pottins and Goldie discuss the space-saving attraction of a wall-hung combi unit installation.

of modern combi units to the evolution of the cell phone. “They started as this big device and shrank down to a smaller device, and now the cell phones are growing in size again. I think that's what you're going to see with the combi market as well,” said Pottins.

Goldie was glad to hear that opinion.

“I think the market really wants to have a small box on the wall, but although it’s smaller and fits on a wall it still takes up the same footprint because you're not really using that space underneath it. So, whether it's standing on the floor or hanging on the wall it's taking up the same amount of space.

And I do like to see storage for both hot water and from a heating point of view because it gives you a bit of a buffer.”

And Pottins noted that more and more often he’s seeing smaller combi boilers getting installed and then realizing that the domestic flow is not keeping up with the demands of the house,

so an external 30-gallon storage tank is being added to create recirculation and mass in the system. “I feel like that's going to soon be the new norm,” he said.

If units are not storing hot water in a tank, Goldie explained, they need a lot of firepower to make enough hot water in order to make it on demand. “You need about 33,000 Btus for every gallon-aminute at showering temperature (so with 40F incoming water, a 65F delta-t that's going to give you 105F shower water, with one shower head at about twoand-a-half to three gallons-a-minute, you're looking at 100,000 Btus). Now if you want to do two showers, you're looking at 200,000 Btus, so it's no accident that the tankless water heaters are all sized around 200,000 Btu.” Pottins showed an example of an older house that was renovated and heavily insulated, and they stuck a smaller combi unit (around 110,000 Continued on p46 HPACMAG.COM

Need to Handle Both Space Heating and Hot Water Demands of Today’s Modern Homes?

THE BRUTE FT MAKES IT EASY. ®

The Brute FT® Combination Boiler and Water Heater utilizes the latest in fire tube technology to offer your customers: • Exceptional Efficiency. The Brute FT®’s modulating technology automatically adjusts fuel usage to match heat demand – to help your customers save on heating utility bills compared to standard “on-off” boilers! ENERGY STAR® rated, 95% AFUE. • Outstanding Performance with Higher Flow Rates (4.8 GPM at a 77°F rise). The Brute FT® Combi has a shell-and-tube domestic hot water heat exchanger that gives your customers unrestricted flow and better performance than brazed plate heat exchangers.

©2020, Bradford White Corporation. All rights reserved. BWHPAC

• Quicker Hot Water Delivery. The Brute FT® combines storage with on-demand hot water for faster performance.

• Compact Design. Easy to install and service, even in tight spaces.

• Excellent Flexibility. The Brute FT® is field convertible between natural gas & propane, is cascadable up to 20 units, and can be vented with PVC, CPVC, or polypropylene.

To learn more about the Brute FT® Combi, visit bradfordwhite.com

Built to be the Best®

< BOILERS

Continued from p44

Btus) in the attic. The heating side kept up no problem because the heat loss of the house was very minimal, but because it required more DHW flow an external storage tank was required.

Both agreed that combi units are well suited to newly-built or renovated homes, but in Pottins’ example, a 200,000 Btu combi would have worked out well on the domestic side, but would have been too many Btus on the heating side.

“The discrepancy in the size of the heating load and the domestic water load is a good point,” noted Goldie. “We run into issues where we are oversized on heating are we going to be short cycling, but the modulation on new boilers has come a long way (like 10-to-1 turn down rate on modulation is pretty standard now), so a 200,000 Btu boiler can modulate as low as 20,000 Btu to meter heat load. So that's great, but still too big to do a lot of the micro loads if you're doing multi zoning in a house.”

COMPACT FIT The final image shared by Pottins during the webinar was a wall-hung combi boiler installation that replaced a large older boiler and hot water storage tank.

The tidy installation demonstrated the space saved in the basement of this older house. Both acknowledged how older homes used to allow for larger mechanical rooms, but that’s not the case today.

“My argument is, are combi boilers going to do the best job at all things? I’d say no, not necessarily,” said Goldie. “If I had the money and the space, I'm going to have a boiler and an indirect hot water tank with decent storage, and I'm going to have a buffer tank so I can manage all my micro loads and not short cycle the boiler.

“But the reality is, contractors and homeowners want to do everything and they give you a space not much bigger than a bread box. That's the challenge we're facing.”

46

HPAC | OCTOBER 2020

An older storage-based combi unit.

Compact combi unit installed in attic space with added storage tank.

Confirming Steve’s remarks, Pottins noted how in Toronto he’s seen a lot of houses where they're built narrow and vertical, and there are multiple bathrooms and two laundry rooms but only one tiny little mechanical room.

Goldie believes there are still a lot of misunderstandings in the marketplace about domestic hot water production.

“The perception is a little tankless in the wall can do all the hot water you need forever. And it can, at a fixed flow rate, but if you've got a big multi-flow shower head that's got five body sprays and a big rainfall head that's pumping out eight, nine, 10 gallons-a-minute, you're not going to get that from a tankless or a small on-demand combi boiler.”

Some of the challenges raised with combi boilers: • meeting high hot water flow demands • instant hot water with water recirculation is a struggle if you don't have any storage • no heat also means no hot water (although Goldie pushed back on this one: “Whether I have two things I need to fix or one thing, I’m going to get it fixed right away.”)

• units have fewer built-in controls for more complex heating setups.

PROS AND CONS Together they both identified some of the clear advantages of the combi boiler: • compact design of combined heating and hot water in one box is very appealing • modern boilers running at potentially 95% efficiency on the heating side are energy efficient • on demand hot water that will run continuously with proper flow demand • economical, combi units are available for only a slight premium over a boiler alone.

• Pottins added that in cases where homeowners are looking at moving into hydronics, a combi unit with an air handler is an easy switch from a furnace and a hot water tank.

KEY TAKEAWAY For both Goldie and Pottins, the key message, for not just this topic but for many mechanical contracting topics, is to have a clear understanding of the application and your ability to meet the expectations of the end user.

“Unfortunately, this is where things do fall down,” said Goldie. “I think that we either don't do a good enough job of explaining the limitations of the equipment we're selling, or people want to sell good news and promise the world (oh yes, you'll never run out of hot water), and I fight this all the time.”

Both see a place for combi units in our marketplace, as long as the expectations are properly explained and understood by the end user. <> Following their discussion, Goldie and Pottins also answered live viewer questions. To see and hear the entire webinar recording, including the Q&A, visit: hpacmag.com/tech-pulse/ HPACMAG.COM

an all star lineup

P-K Storm™ with Nuro ® Control system

The P-K STORM™ with NURO® Touchscreen Control from Patterson-Kelley Patterson-Kelley’s newest stainless-steel condensing boiler, the P-K STORM is designed for maximized comfort during those long cold winter days. The STORM has quickly proven to be one of the highest quality and most efficient condensing products on the market.

Our proprietary NURO® Control System is equipped standard on all P-K STORM boilers.

Designed to maximize overall boiler efficiency, the NURO utilizes the most advanced technology available in a simple, yet intuitive interface. This ensures safe, efficient, and reliable boiler performance year-after-year.

STORM™ Capabilities

✓ ✓ ✓ ✓ ✓

1250-4000 MBTUs Up to 97% Thermal Efficiency 10:1 Mechanical Turndown Outdoor Models Shipped Fully Assembled SCAQMD and BAAQMD Certified

Patterson-Kelley, LLC

NURO® Capabilities

✓ 7” Inch Color Touchscreen Display ✓ View and Manage your Boiler from Anywhere In the World with an Internet Connection ✓ Easy to use Setup Wizard ✓ Fully Customizable Night Setback and 7-Day Load Schedule www.pattersonkelley.com | 877.728.5351

HYDRONIC PRODUCTS Webstone announces the first forged brass Gas Sediment Trap. Taking the place of a fieldfabricated assembly, the integrated trap design offers a clean, quality and professionallooking

gas

appliance

installation.

The

three-piece Gas Sediment Trap kit includes the required CSA certified gas ball valve and 24-in. x ¾-in. flex hose needed to complete the installation.webstonevalves.com

Weil-McLain Canada’s new ECO Tec high-efficiency condensing boilers for residential applications deliver up to 95% efficiency in seven sizes (4 heating/3 combi) providing space heating and up to 5.4 GPM of domestic hot water at a 70F rise. The ECO Tec models feature durable stainless steel fire tube heat exchanger, four thermostat inputs, built-in ECM Circulator, and can power and control up to five circuThe RIDGID RP 342-XL Press Tool offers a

lators. weil-mclain.ca Belimo Americas optimized UBLK zone valve

lightweight design and can press ½-in. to 4-in.

retrofit solutions are replacement solutions for

copper, stainless steel and carbon steel pipe,

existing failed actuators on TACO Zone Sentry

and ½-in. to 2-in. PEX pipe – in under 12 sec-

zone valves, Schneider Electric VBB ball valves,

onds. Its QuickSwitch technology can go from

or TAC Erie VM zone valves with the Belimo

Standard to Extended 32kN applications to

compact CQ actuators. The series of replace-

press 2-½-in. to 4-in. carbon steel. It’s also

ment solutions restores service without remov-

compatible with RIDGID’s full line of standard

ing the valve. belimo.us

32kN press tool accessories. ridgid.com

Armstrong has two new COMPASS R high efficiency models. The R20-35 and R40-45 circulators feature air-cooled ECMs and advanced Design Envelope variable speed technology.

The circulators can replace many competing models with bolt-for-bolt connection capability and cover a wide performance range. They offer multiple control options including a patent-

Cleaver-Brooks new ProFire SBR-5 series burners for industrial applications are compatible with a

ed ‘Auto’ mode and an easy selection of ap-

variety of boiler types, such as firetube and watertube boilers, and the burner series is capable of

propriate flow and pressure to meet system

less than 5 ppm NOx emissions with flue gas recirculation. The burner features a unique fire head

demand. armstrongfluidtechnology.com

design to achieve controlled combustion, resulting in ultra-low emissions with 3% O2 achievable for all firing rates.cleaverbrooks.com

48

HPAC | OCTOBER 2020

HPACMAG.COM

SIMPLY BETTER HEATING & COOLING CONTROLS

Introducing Our New WIFI Thermostat

• Available at wholesale locations across Canada • Model ST920WF (3H/2C touch buttons) or Model ST921WF (2H/1C press buttons) • Both models can be programmable or non-programmable • 24V power (C-wire extender kit optional) • WiFi 2.4Ghz • Salus Solo mobile app for Apple and Android devices • Works with Google Home or Alexa • Easy to install and use info@hydronitech.ca • 450-231-2836

www.salusinc.com

www.hydronitech.ca

MECHANICAL SUPPLY NEWS MANUFACTURERS • DISTRIBUTORS • WHOLESALERS

EMCO OPENS NEW KOHLER SIGNATURE STORE IN TORONTO EMCO Corp., a national wholesale distributor of plumbing and HVAC products, has opened Ontario’s first Kohler Signature Store in Toronto, a 4,000 sq. ft. space located in the city’s Castlefield Design District.

The storefront allows homeowners and designers the view the Kohler family of brands including Kohler Plumbing, Kohler Lighting, Kallista Plumbing, Robern, and Ann Sacks Tile and Stone.

In-store consultants will also assist consumers and trade professionals with their bathroom and kitchen needs.

This is the second KOHLER Signature Store opened in Canada in partnership with EMCO. The other location is in Vancouver.

“We are excited to partner with Kohler on another Signature Store location, and we believe Toronto is the ideal market to continue to grow,” said Tom Newell, regional VP and general manager for EMCO, in a company release.

“EMCO is dedicated to providing our customers with the best in quality and innovative plumbing products.”

EMCO also owns the network of The Ensuite Bath & Kitchen showrooms across Canada. www.kohlersignaturestoretoronto.com RLS GOING ON ITS OWN RLS, manufacturer of the RLS Rapid Locking System line of press fittings for the HVAC and refrigeration industries, will no longer supply its patented press 50

HPAC | OCTOBER 2020

fittings to Parker Hannifin Corp. for its ZoomLock brand. RLS fittings are now being sold under the company’s own branding going forward.

RLS issued a release with this announcement to avoid confusion in the marketplace as to the source of fittings sold under the ZoomLock brand. RLS designs, develops and manufactures its fittings engineered for high pressure connections in the air conditioning and refrigeration industries. RLS introduced its patented fittings in 2015 and partnered exclusively with Parker at that time.

The company manufactured and supplied millions of fittings for Parker’s Sporlan Division to sell under the ZoomLock brand. However, RLS recently decided not to renew that exclusive partnership. RLS has learned Parker plans to source fittings for its ZoomLock brand from Conex Universal Ltd. in the United Kingdom. RLS previously filed patent lawsuits against Conex in the U.S. and the UK alleging Conex infringed claims of RLS’s patents.

RLS and Conex agreed to settle the lawsuits. As part of the settlement, Conex agreed, without admitting liability or infringement, that it would stop selling the design of its fitting that RLS accused of infringement in the lawsuits. www.rapidlockingsystem.com CIPH VIRTUAL CHARITY AUCTION RAISES OVER $10K Celebrating a 25-year fundraising relationship with Habitat for Humanity, the Canadian Plumbing and Heating Institute (CIPH) held a virtual auction online in late July to raise funds for the non-profit organization that helps families in need of safe and affordable housing across Canada.

CIPH announced that it had raised $10,805 in support of the charity with this year’s virtual event. ciph.com

New merged Wolseley location in Cornwall, Ont

>> NEW LOCATIONS: Wolseley Canada has merged its two branches in Cornwall, Ont. into one new modernized location at 2900 Marleau Avenue.

Jason Lobb is the branch manager of the newly combined wholesale location, which offers both plumbing and HVAC/R inventory.

The two previous branches, located at 2901 Marleau Avenue and 650 Cumberland Street, are now closed. wolseleyinc.ca >> Noble has opened its newest branch for servicing customers in the Collingwood area, north of Barrie, Ont. The new location is at 199 Mountain Rd., Collingwood, Ont. L9Y 3Z9. The branch is open Monday – Friday, 6:30 am – 5:00 pm. noble.ca >> Equipco Ltd. Ontario has announced its offices have relocated to 154 Caverly Rd., Aylmer, Ont., and that no further shipments will be received at 3-6480 Viscount Rd, Mississauga, Ont. location. equipcoltd.com

WOLSELEY CANADA IMPLEMENTS COUNTRY-WIDE MASK WEARING POLICY In an announcement sent out nationally, Wolseley Canada is enforcing the mandatory wearing of face coverings at all of its locations as of September 21, 2020.

The company’s mandatory face coverings policy includes exemptions for those who cannot wear a mask for medical reasons, children under the age of two, and other reasonable accommodations.

Continued on p52 HPACMAG.COM

Modular VRF heat pump and heat recovery systems

– NEW AT MASTER* –

575V AIR-SOURCE VRF SYSTEMS • Inverter compressors for superior performance and exceptional efficiency • 575V heat pump line offering Priority Cooling Control • Large-capacity single outdoor units (up to 16 ton). High-capacity units increase layout flexibility, simplify installation, save space, reduce weight and decrease the number of piping and electrical connections • Exceptional design flexibility and long-term savings on energy and maintenance • Maintenance-friendly design. All components are accessible from the front for fast, easy,

cost-efficient maintenance.

• 10-year warranty on parts and compressors

*Available in Ontario, Quebec and Atlantic Provinces only.

MASTER IN COMFORT. EXPERT IN TOP BRANDS.

visit us at

< MSN

Continued from p50

The wearing of face coverings is in addition to the safety protocols that Wolseley Canada put in place earlier this year, including limited branch capacity and enhanced cleaning procedures.

“The health and safety of our associates, customers and vendors is a top priority for our organization,” said Kevin Fancey, president of Wolseley Canada in the company release. “As we approach cold and flu season, we want to take every necessary precaution to ensure we continue to keep everyone safe and help prevent the spread of COVID-19.”

Wolseley Canada is also encouraging contactless options for ordering, including online orders via the company’s Wolseley Express (for plumbing, HVAC/R and Waterworks customers), Express Pick-Up, and curbside pick-up. wolseleyinc.ca

VIEGA EXPANDING NORTH AMERICAN MANUFACTURING OPERATION Production lines from Europe are transferring to the company's plant in Kansas.

Viega LLC, the North American division of the German-based company, has added production lines to its Kansas manufacturing operations to speed up distribution and allow the company to move more production from Germany to North America.

The most recent expansion is a 200,000 sq. ft. manufacturing plant.

“These latest expansions will allow us to increase production of our ProPress copper line and get shipments to distributors and customers faster than ever,” said Viega COO Robert Boots.

When fully operational, the new plant will house additional ProPress production lines of various products and sizes.

Many of those products have been manufactured in Germany, but the company is moving some production to Kansas to accommodate growth in the North American market. viega.us

HPAC WEBINAR November 20th at 1:00 EST

Anticipated length: 50 minutes with 10 minutes for Q&A John Siegenthaler

PART TWO: Why air-to-water heat pumps are a market opportunity for hydronic professionals.

Part 1 of this webinar introduced the concept and market potential for air-to-water heat pumps in North America. If you missed Part 1 it can be viewed at www.HPACmag. com. Part 2 will drill down into more detail on how to apply modern air-to-water heat pumps, including design details, performance simulations, and several example systems.

If you design hydronic heating and cooling systems, Part 2 will provide you with several take-ways to help maximize the performance of air-to-water heat pumps in a variety of system configurations.

LEARNING OBJECTIVE: • Understand how performance estimates can be achieved using spreadsheets • Learn when buffer tanks are required and when they are not needed.

• See how air-to-water heat pumps can provide space heating, cooling, and domestic hot water • Understand basic control concepts applicable to air-to-water heat pump systems

Register for FREE at www.hpacmag.com Presented by

52

HPAC | OCTOBER 2020

HPACMAG.COM

PEOPLE > Navien has appointed Adam Wills as its new national sales manager for Canada. Wills brings over 16 years of experience in water heating and HVAC in both manufacturing and distribution.

Recently, he led the Canadian HVAC business and Wills national customer service strategy with Rheem. Wills also brings extensive tankless water heater experience.

Ouellet Canada has appointed Yves Giard as regional sales manager, Convectair products. Giard has over nine years of experience as a sales Giard manager with Convectair. He will manage a new sales team, which includes three territory managers: Eric Joncas, Jonathan Bond and JeanPierre Brunelle.

Brunelle

Bond

Joncas

Rheem has named Dave Simpson as director of sales Canada. Simpson comes to Rheem with almost 20 years of experience within construction and industrial sales, most recently as the regional VP sales and operations with Gentek Simpson Building Supplies. He previously held various leadership positions with Hilti, Wolseley Canada and GOJO Industries Inc. Uponor has appointed Chris Hartwick as general manager, Uponor Canada. Most recently Hartwick was the director of sales for commercial building services, in the U.S. and Canada, at Xylem Inc. and previously, he was vice president of Xylem Hartwick Canada and managing director for the Canadian Applied Water Systems division.

Lafert North America, supplier of motors and drives, has named Douglas Backman as North American sales director. Backman brings over 30 years of leadership in the electrical industry with experience in both Canada and the U.S., most re- Backman cently as vice president of Danfoss (Vacon) Canada Inc. for the past 10 years.

Aqua-Tech Sales and Marketing Inc. has added Marc Sorel as a technical sales representative for the eastern Ontario region. A graduate of Algonquin College in Ottawa, Sorel brings 30-plus years of experience in the distribution side of Sorel business. He will be located in Ottawa and work with territory sales representative, Don Smith of D & M Mechanical Sales and the entire Aqua-Tech sales team.

Viega, LLC has named Markus Brettschneider as its new president/CEO replacing Dave Garlow.

Brettschneider was most recently with ABB. He is now responsible for the overall operations of Viega LLC headquartered in Colorado.

Brettschneider

Keith Farrell has joined the management team at Ontor Ltd. in the role of vice president, sales and marketing. Farrell brings over 30 years of HVAC industry experience, most recently as president Farrell of Riello North America.

Desco Plumbing and Heating Supply has promoted Diana Di Carlo to marketing and retail manCuadra Mehta ager, responsible for all Di Carlo marketing activities and leadership of the Water Closet showroom business; Paul Mehta is now pricing and product manager, responsible for pricing practices and product line rationalization; and Fidel Cuadra has been promoted to quotations manager with responsibility for all plumbing and heating projects in the GTA.

EASY. SAFE. FREE.

THERMOSTAT RECYCLING

We recycle all elements of the thermostat; plastic, metal, electronics and mercury (which is particularly hazardous).

Do your part and join the more than 1,500 contractors already participating in the program.

FOR MORE INFORMATION www.hrai.ca/trp 1(800)267-2231, x 273

Administered & delivered by: Supported by:

OCTOBER 2020 | HPAC

HPACMAG.COM HPAC_March_TRP.indd 1

53

2019-02-26 11:27 AM

< SOLAR THERMAL

LARGE-SCALE SOLAR THERMAL SYSTEMS A review of how far we’ve come and lessons that can be applied to smaller systems. BY ROBERT WATERS

T

he solar thermal industry is one that I have personally had a strong relationship with in my almost 40 year career in the mechanical industry. This relationship started in the early 1980’s, then faded away for over 20 years before coming back to life in the early 2000’s. I wrote about the roller coaster solar thermal market previously in the October 2016 HPAC article “Solar Thermal Runs Hot and Cold.”

I still believe strongly in solar thermal technology and its ability to provide green renewable energy to assist the hydronic heating industry. The solar thermal sector in Canada, as well as other areas in the world, however has suffered a downturn in the last 10 years. Pressure from cheap natural gas prices and the growth of the solar photovoltaic (PV) market have been the two biggest factors that have caused struggles for the solar thermal sector.

Unlike the PV market, which converts the sun’s radiation directly to electrons and electricity, solar thermal has a broader range of uses, collecting the sun’s heat and transferring it to a medium, and that stored energy is then used for purposes including heating and cooling a home.

The current state of the world solar thermal market was recently highlighted in the 2020 edition of the report “Solar Heat Worldwide,” published by the International Energy. This report highlights the 2019 global market developments and trends.

In 2019 solar thermal saw shrinking volumes in large markets like China, 54

HPAC | OCTOBER 2020

The recent International Energy Agency report, Solar Heat Worldwide, provides a global overview of the market.

the U.S., Germany and Australia. Even with this downward trend there is still a great story to tell here. Solar thermal is still a growing market in many regions, has a huge environmental impact, and has a positive impact on jobs.

Certain regions of the world have very strong growth markets including Denmark, Cyprus, South Africa, Greece, Brazil and India. This is still a big industry worldwide with a US$16.9 billion turnover in 2018, providing an estimated 650,000 jobs in production, installation and maintenance.

Solar thermal continues to provide a positive impact worldwide on renewable energy production and climate protection. There was a cumulative solar thermal capacity in operation at the end of 2019 of 684 million square me-

ters of collector area (479 GWth). This provides an annual greenhouse gas emission reduction of over 135 million tons of CO2.

Traditionally the largest segment of the world market was made up of small-scale single family home domestic hot water systems. This has changed as these small residential systems made up only 33% of the new installations in 2018.

A bright spot for this market segment is the success of thermosiphon systems in warm climates with little worry of freezing conditions. Some countries such as Greece, South Africa, Brazil and some countries in Latin America, have strong markets in thermosiphon systems due in part to government support programs linked to social housing (see Figure 1).

The largest segment of the world market is now from medium-scale domestic hot water applications making up 60% of new installed worldwide capacity. These systems are typically installed in apartment buildings, hotels, public buildings, etc. They usually have a better economy of scale due to their high volume and year-round domestic hot water heating requirements. These types of systems are generally pumped systems, using either closed-loop design with freeze proof heat transfer fluid, or drainback systems using water.

One segment of the solar thermal market I would like to highlight is largescale systems, as they have become a real success story. There has been strong and steady growth with largeHPACMAG.COM

DISTRICT HEATING District heating systems are ideally suited to solar thermal due to their large and steady loads.

These systems are being installed with massively sized collector fields and huge in-ground storage to provide large percentages of the annual heat required for space heating and domestic hot water heating (see Figure 2).

District heating systems are quite common in Europe, and this is where most of the solar district heating plants are found with almost 300 of these large scale solar systems (>500 m2) now in operation. There is currently only one system in Canada located at the Drake Landing Solar Community in Okatoks, Alberta. It has been in operation since 2007 and consists of 2,300

SOURCE: ARCON-SUNMARK

SOURCE: SOLAREM/TUMA INDUSTRIAL

scale systems that are being used for two sectors: district heating and industrial processes.

Figure 1. Thermosiphon systems in a social housing program in Brazil.

Figure 2. Solar district heating system in Voljens, Denmark

m2 of collectors connected to a borehole storage system. It provides almost all of the heating requirements for a subdivision of 52 homes.

Denmark is the leader by far, not only in Europe but worldwide, in the number of systems and installed capacity. By the end of 2019 a total number of 123 systems with 1,554,973 m2 of collector area has been installed in Denmark.

In 2019 alone 15 new solar district

heating projects were built in Denmark.

Other countries with large numbers of these large-scale systems are Germany (40), Austria (28), Sweden (25) and France (15). China has also started to install more of these systems in the last few years and now has 64 systems.

Most of these large-scale solar installations are large ground mounted flat plate collector fields that are located Continued on p56

YS !

3 LIVE DA ual booth!

M eet u s a

t our virt

, EST am – 2 pm Nov 5: 10 , EST pm 9 – pm 5 Nov 12: n), EST oo (n 12 am – Nov 19: 8

HPACMAG.COM

OCTOBER 2020 | HPAC

55

< SOLAR THERMAL Continued from p55

HPAC | OCTOBER 2020

Figure 3. Solar district heating system with seasonal pit storage in Gram, Denmark.

(55.4 million gallons). Some of the larger pits have over 2,000 liters of storage for every m2 of collector (see Figure 4).

LESSONS LEARNED So what lessons can be learned from these large-scale systems by Canadian contractors who are interested in small-scale solar thermal heating system installations?

In my opinion the most important message is all about storage. Lots of thermal storage is essential for any combination solar-hydronic system. In my experience storage is also the most common component that is skimped on when people have installed these systems.

Installing lots of solar panels is the easy part, and some think that more panel area will make for a better system.

I have seen this way of thinking proven wrong many times, and it has led to the downfall of many solar heating systems.

The reality is solar storage tanks are expensive, take up a lot of space, and they’re hidden in the basement. Many see this as a simple area to cut corners. The solar panels however will still create heat even without sufficient storage, and this almost inevitably leads to overheating problems: pressure relief valves blowing off, glycol getting cooked and turning to sludge, and collector arrays plugging up.

So learn from these large-scale solar thermal systems and use lots of thermal storage. Why is it so crucial to store energy? Heating loads, whether do-

SOURCE: RAMBOLL

56

SOURCE: RAMBOLL

close to the district heating distribution lines. These systems are equipped with large capacity seasonal thermal storage systems that are either large above ground tanks or in many cases in-ground heat storage. The size of the collector arrays can be enormous with many systems covering between 2,000 to 15,000 m2. Denmark is the world leader in really big systems with 20-plus systems in the 20,000 to 37,000 m2 range, and the world’s largest is in Silkeborg having 156,000 m3 of collectors.

Seasonal storage of the energy from these huge collector arrays is important, as most of the solar energy is produced in the summer and used for heating in the winter. To meet this requirement inexpensive and innovative storage techniques have been developed. For smaller systems typically insulated steel tanks are used, but for large systems either borehole storage or pit heat storage systems are more cost effective (see Figure 3).

Borehole storage uses the heat capacity of the soil to store thermal energy underground. Multiple boreholes are drilled in the ground for the heat exchanger to transfer heat to and from the soil. This type of storage system has been utilized in Drake Landing in Alberta with great success, where they utilize 144 holes each 115 ft deep.

Seasonal pit heat storage systems are typically constructed by excavating a hole in the ground, lining the bottom of the pit with a waterproof membrane to avoid leakage, then filled with water.

The top of the pit will be covered with a floating insulation blanket to slow down the heat loss. They have proven to be relatively inexpensive, effective and reliable solutions for heat storage.

These pit heat storage systems have massive volumes with sizes up to 75,000 m3 (19.8 million gallons) or larger. The largest in the world is in Vojens, Denmark being 210,000 m3

Figure 4. Construction of seasonal pit storage in Denmark.

mestic hot water or space heating, rarely occur at the same time that solar radiation is being collected by the panels. If the storage is not sufficient when the sun is shining then the whole circuit will overheat causing problems.

Just as important is the loss of potential energy collection, as the system will shut off at its maximum storage tank temperature limit.

Some good rules of thumb to use for solar system storage: for solar systems that do DHW heating only use 50 to 80 litres of storage per m2 of collector area; for solar systems that are also providing space heating, more storage volume is required (80 to 100 L/m2).

These are minimum values that are recommended. More storage volume can be used as there is almost no such thing as too much.

The sun is almost ready to set on my hydronic-solar career. I’ve seen the great progress in solar panel technology, solar system components, solar controls and system design knowledge. I hope that solar thermal technology sees another resurgence in Canada. It’s probably too late in my career for me to take part in it, but I trust there will be other wet heads to take the solar thermal torch and run with it when the time comes. <> Robert Waters, founder of Solar Water Services Inc. can be reached at solwatservices@gmail.com.

HPACMAG.COM

Nov. 30 - Dec. 4, 2020

Register Now Brought to You Virtually By

thebuildingsshow.com #BUILDINGSWEEK

< REFRIGERATION

THE POWER OF THE HORSE Reminiscing and understanding the dynamic relationship of horsepower in refrigeration. BY DAVE DEMMA

I

entered high school in 1967, and graduated in 1971. I experienced the social changes brought about by the Vietnam War, and the ensuing protests from the “counter culture”.

Their message of peace, love, change and enlightenment was certainly present in the music of the day, and that music very much caught my attention.

Like many of my friends, I purchased an electric guitar and formed a band. We were OK, played some gigs, and my interest in music continued through college. I was even serious enough about it to start the process of changing my course of study from engineering to music.

Part of that process included informing my Engineering Department Head, and having him sign my “change of major” application. I’m forever grateful to that Department Head, William Phaklides, for (1) congratulating me on 58

HPAC | OCTOBER 2020

my apparent new course of study, and (2) asking the question that caused me to seriously contemplate my future.

That question: “How are you planning to earn a living with a music degree?”

I don’t recall what my response to him was. But I do recall that the question haunted me.

After a week of mental torment, coupled by serious pondering, I made the decision to “stay the course.” I have often wondered where I would be had that question not been asked of me.

I have retained my passion for playing music, and I still have the opportunity to perform now and then. But I have a great passion for this industry too. It’s interesting, vast in its application, technological, and touches so many facets of our lives. And as the COVID-19 situation has reaffirmed, it is an absolutely essential industry.

POSTIMAGE.ORG

The Chevy 409 engine from the early 60s.

But, I digress…

My junior high years included the earlier part of the 1960s, and I was listening to the Beach Boys (and other groups) who were singing about surfing, girls and cars. When I think of the term “horsepower”, I think back to high school and the various cars I owned.

When I hear, “She’s real fine, my 409”, it reminds me of my 57 Chevy, which had a 348 engine (bored out to a 390 displacement). The 348 was the baby brother of the 409 (pictured).

And when meeting up with other buddies who had hot cars, the common bragging point was always HORSEPOWER. Can you imagine the harnessing nightmare necessary to arrange 425 thoroughbred stallions, in groupings of four, pulling a 57 Chevy down the dragstrip?

The term horsepower (HP) was the brainchild of Scottish inventor/engineer James Watt. After making technological advances to the steam engine, he had trouble marketing to those who still relied on the trusted horse. After frequent questions about “how many horses would one steam engine replace?” he set upon a testing method that would provide an accurate answer.

Watt devised a test where horses drove a wheel connected to a pulley system which lifted a measured load of coal. His calculations determined that a horse could on average lift around 33,000 foot pounds per minute, with one foot-pound being the force necessary to lift 1 pound over 1 foot of distance. Watt’s new term “horsepower” converted to the more meaningful 33,000 ft-lb/min. This relationship still holds true today.

In today’s world, the term horsepower has become synonymous with many things which have absolutely nothing to do with mechanical work, for example a computer chip can be described as having plenty of horsepower.

And you also can add “tons” to the Continued on p60 HPACMAG.COM

Attention ZoomLock Users: RLS issued the following press release on August 13, 2020.

August 13, 2020 FOR IMMEDIATE RELEASE August 13, 2020

nifin Corporation RLS® LLC Ends Relationship with Parker Han Brand ely Under Its Own atio s Fittings Exclusiv n ply Its Patented Pres por Cor n nifi Han RLS Will Now Sup ker RLS® LLC Ends Relationship with Par ker”)

Corporation (“Par patented press fittings to Parker Hannifin RLS® LLC (“RLS”) will no longer supply its in the marketplace as sion confu announcement to help avoid for the ZoomLock® brand. RLS is making this ard. forw going d r the ZoomLock bran to the source and quality of fittings sold unde nifin Corporation gs to Parker Han press fittin patented its ly er supp a Berk ns, develops, and S”) will noonlong away company. RLS desig Hath RLS® LLC (“RL shire n Inc., ings, avoid conf Hold help to t Marm uncemen airusio thisdanno RLS is a subsidiary of ZoomLock™ brand. RLS is makingeere for high-pressure connections in the d the for ngs engin ”) tti fi rker nted (“Pa pate its rica Ame in bran ures Lock ufact Zoom theandin erdem proudly man und g conventional sold of tifittin and itythe ming qual onsu and ce. By me-cgs cing as to repla lace erati stries indusour mar onthe in the and refrig g ketp itionin cond ections that conn t isten cons more r, faste s, RLS’s fittings allow for practice of manually brazing copper joint safety. reduce total installed cost while enhancing that time. RLS has and partnered exclusively with Parker at RLS introduced its patented fittings in 2015 under the sell to ion Divis of fittings for Parker’s Sporlan since manufactured and supplied millions ZoomLock brand. decision was made, w its exclusive partnership with Parker. This However, RLS recently decided not to rene to customers as along d pricing provided to Parker was not passe in part, because RLS believes discounted unts at issue and disco the of most LLC, said Parker has paid back intended. Paul Schubert, President of RLS funds.

RLS expects to fully recover the remaining x Universal Limited e fittings for its ZoomLock brand from Cone RLS has also learned Parker plans to sourc (“Conex”) in the United Kingdom. d Kingdom alleging st Conex in the United States and the Unite RLS previously filed patent lawsuits again June of 2019. As part in its lawsu the le sett to d and Conex agree Conex infringed claims of RLS’s patents. RLS d stop selling the woul admitting liability or infringement, that it of the settlement, Conex agreed, without gement in the lawsuits. design of its fitting that RLS accused of infrin fittings and are featured only complete range of refrigerant press Today, RLS’s patented fittings remain the proven by millions of backed by a 10-year limited warranty and in the Copper Tube Handbook. They are also fittings installed. uct line to Parker to patented, proven, and made in America prod “To be clear, RLS will no longer supply its the high-quality with ped equip are users said. “To ensure end sell under the ZoomLock brand,” Schubert ding going forward. ct, look for RLS’s fittings under its own bran product they need and have come to expe quality connection.”

The RLS brand is your assurance of the same mation on RLS’s patented fittings.

Visit rapidlockingsystem.com for more infor

- more -

rapidlockingsystem.com • 833-RLS-FAST

< REFRIGERATION Continued from p58

Figure 1.

Figure 2

list of appropriated words, as in tons of capacity for a refrigeration system, component, etc. Of course, one ton = 12,000 Btu, which is a measurement of heat content. There is no definable correlation between heat content and mechanical work.

Working in the HVAC/R distribution business, it’s not uncommon to hear a technician ask for a 3 HP expansion valve, or perhaps an expansion valve for a 3 HP system. Or a 5 HP compressor.

In the HVAC/R industry, the use of the term HP when referring to anything other an electric motor is not useful.

Expansion valves tonnages are determined by the properties of the refrigerant in use, the mass flow through the valve, and the design conditions which the system will be operating under.

Compressor capacity is determined by the compressor displacement, the compressor efficiency, the compressor motor speed, the refrigerant properties and the system conditions.

To illustrate the point refer to Figure 1 showing a compressor selection for a specific design condition: R-448A, 48,000 Btu, -35F SST, 120F SCT. For comparison, compressor capacity for optional SCT conditions is also shown.

The application requiring a -35F SST 60

HPAC | OCTOBER 2020

and 105F SCT will require approximately 3.2 HP for every ton required.

One of the application criteria to determine compressor capacity is the discharge pressure, which is determined by the condensing temperature. You’ll notice that the compressor capacity increases as the SCT is reduced. This should reveal the need for a properly sized, and maintained (clean) condenser to keep the discharge pressure as low as possible, which results in the most efficient compressor operation.

In addition, it also reveals the reason why many larger refrigeration systems (such as supermarkets) are set up to operate at the lowest* possible condensing temperature, during the lower ambient temperature months. A multicompressor refrigeration rack, requiring a capacity of 90,000 Btu, would require two of these 6D compressors to operate at a 120F SCT, but only one compressor at a 75F SCT. (* Lowest possible means abiding by compressor manufacturer’s guidelines, and maintaining sufficient liquid pressure to allow expansion devices to operate at the capacity necessary for the application.)

Figure 2 (above) is a more comprehensive comparison of the relationship between Btu capacity (tons) and HP, at

varying SST conditions and a consistent SCT condition.

For a given application, as the SST increases, the HP requirement reduces. In addition to the conditions changing the HP/Ton requirement, this also reveals how the compressor efficiency (compressor type) will influence that. Based on the capacity numbers, it appears reciprocating compressors (with the discus valve plates) are more efficient than scroll compressors. (It should be stated that the compressor capacity information comes from Copeland’s product selection software.)

Now, when Tennessee Ernie Ford sang his 1955 number one hit “16 Tons”, was he singing about air conditioning?

No, he was singing about 16 tons of coal! <> Dave Demma holds a degree in refrigeration engineering and worked as a journeyman refrigeration technician before moving into the manufacturing sector where he regularly trains contractor and engineering groups. He can be reached at ddemma@uri.com.

HPACMAG.COM

TRAINING

VIRTUAL TRAINING OPPORTUNITIES Selling HVAC upgrades and IAQ

HRAI is offering a two-module online workshop where HVAC professionals will learn how to communicate the value and effectiveness of HVAC products and services in improving indoor air quality, in a responsible manner, demonstrating a long-term commitment to the health, well-being and comfort of your clients. These new workshops will empower participants to offer responsible technologies and services in the residential and commercial sector to optimize indoor environmental control during the pandemic and beyond.

Module A "Indoor Air Quality and selling HVAC upgrades" will outline how the science supports at least four strategies for enhancing mechanical systems and how they can be implemented most effectively into existing HVAC systems. The role of ventilation, filtration, distribution and humidity control will all be explored. And Module B is "Principles of running a business in a pandemic" and participants will learn about the fundamentals of ‘comfort sales’ including assessing customers’ needs and refining the sales approach in a pandemic environment. hrai.ca/

covid19-training

TECA Quality First Training (B.C.)

The Thermal Environmental Comfort Association (TECA) Quality First training programs are developed by the industry, etting minimum standards for the residential and light commercial heating, ventilating and cooling trade in British Columbia. Courses provide contractors the information they need to install equipment that operates safely and comfortably at rated efficiencies. As of May 2020, TECA is now offering on-line training while still maintaining the integrity of its certification. www.teca.ca

Hydronics Training

The Canadian Hydronic Council (CHC) Certification Program is a method to recognize the mastery of a set of industry criteria in hydronic installation, hydronic design or both. Designers and installers become certified is to ensure they are designing/installing systems to industry standards. NAIT and BCIT offer training blocks. www.ciph.com/page/chc_certification

Project Management for Contractors

The Construction Education Council presents the Gold Seal and Blue Seal Accredited Project Management Program. This program is offered in partnership with the University of Waterloo and usually takes place over a 10day period and is split into two five-day sessions, but this year the course is being offered online, two days a week, for 10 weeks throughout November, December, January and February. This will mark the 40th session offered with nearly 900 industry managers graduating from the program.

mcac.ca/event/project-management-for-contractors-10-daygold-seal-accredited-program/

Design Technician Designations

The HRAI Residential Air System Design Technician (RASDT) Designation was established in partnership with Natural Resources Canada (NRCan).

The designation is awarded to all individuals who hold current certification for the following four HRAI training programs: Residential Ventilation using Section 9.32 of the Building Code (as of September 1, 2019), Residential Heat Loss & Heat Gain Calculations, Residential Air System Design and Residential Commissioning.

The HRAI Residential Hydronics Design Technician (RHDT) Designation was also established in partnership with NRCan. The designation is awarded to those who hold current certification for the following four HRAI training programs: Residential Ventilation using Section 9.32 of the Building Code (as of September 1, 2019), Residential Heat Loss & Heat Gain Calculations, Residential Radiant Hydronics Design and Residential Commissioning.

The new HRAI Residential Ventilation Design Technician (RVDT) Designation will be awarded to those who hold current certification for the following four HRAI training programs: Residential Ventilation using Section 9.32 of the Building Code, Residential Ventilation using CSA F326, HRV/ERV Installation & Balancing Fundamentals and Depressurization Testing of Residential Systems.

hrai.ca/rasdt-rhdt-rvdt-designations

THE SOURCE ADVERTISERS IN THIS ISSUE

Adrian Steel......................AdrianSteel.com ...............................p.11

Liberty Pumps ..................LibertyPumps.com ...........................p.17

Amvic.................................amvicsystem.com .............................p.37

Lyncar ................................lyncar.com ........................................p.21

Bradford White.................bradfordwhite.com .......................... p.45

Master Group ...................master.ca..........................................p.51

Brant Radiant Heaters ...brantradiant.com ............................ p.32

Navien................................NavienInc.com..................................p.13

Caleffi ................................caleffi.com ................................p. 35, 39 Chemfax ............................chemfax.com............................... p.2, 63 Conbraco...........................Shurjoint.ApolloValves.com ..............p.27 Franklin Electric ..............littlegiant.com...................................p.19 General Pipe Cleaners ....drainbrain.com/hotspot .....................p.7 Giant ..................................giantinc.com .................................... p.55 Grohe .................................grohe.ca ...........................................p.15

Nudura ...............................nudura.com/hydrofoam .................. p.43 Resideo .............................bit.ly/HomeWaterSolutions ............. p.23 RLS Fittings......................rapidlockingsystem.com.................. p.59 Rosenberg Fans ...............rosenbergcanada.com .....................p.31 Salus ..................................salusinc.com ................................... p.49 Testo ..................................testo.com/en-US/heating-2020 ..... p.64 The Buildings Show.........thebuildingsshow.com......................p.57

Harsco ...............................pattersonkelley.com .........................p.47

Thermostat Recovery Program ...........hrai.ca/trp ....................................... p.53

IBC .....................................ibcboiler.com ......................................p.9

Triangle Tube ....................triangletube.com ..............................p.41

IPEX ...................................ipexaquarise.com ............................ p.25

Viessmann ........................viessmann.ca .....................................p.4

HPACMAG.COM

OCTOBER 2020 | HPAC

61

CALENDAR Women Empowering Women in HVACR October 21-22

CIPHEX VIRTUAL November 2-27

BUILDINGS WEEK November 30 - December 4

The Ontario Refrigeration and Air Conditioning Contractors Association (ORAC) is hosting a virtual two-day Women’s Day event

Canada's online trade show and conference for the plumbing, hydronics and HVAC/R industry.

The virtual show will be open 24/7, with 3 special “live” days and there will be 21 webinar sessions..

A virtual trade show bringing together The Buildings Show and BUILDEX Alberta, including PM Expo, Construct Canada, World of Concrete Toronto, and Homebuilder & Renovator Expo.

www.orac.ca

www.buildexalberta.com

www.thebuildingsshow.com

Retrofit Canada Conference December 2-3 Being held in the City of Vancouver, the first Retrofit Canada Conference will focus on innovation, sustainability and energy efficiency through retrofitting Canada’s infrastructure and buildings.

www.retrofitcanadaconference.com

2021

2020

FOR THE LATEST EVENT NEWS, SEE HPAC'S NEWSLETTER @ HPACMAG.COM

2021 ASHRAE Winter Conference POSTPONED The technical program for the 2021 ASHRAE conference was to be held in January at the Palmer House Hilton in Chicago. A future date is to be determined.

AHR Expo POSTPONED This annual showcase on the future of HVAC/R technology, scheduled to be held in January at the McCormick Place in Chicago may be moved to March 15-17..

www.ahrexpo.com

www.ashrae.org/conferences

ISH 2021 DIGITAL March 22-26

MCEE 2021 April 7-8

MEET 2021 May 5-6

The world’s largest exhibition for the HVAC sector is going virtual. The event will run 24/7 and be accessible around the world..

Industry professionals will gather at the Montreal Convention Centre for the Mécanex/ Climatex/Expolectriq/Éclairage (MCEE) 2021 trade show.

Postponed by a year, the biennial Mechanical, Electrical, Electronic Technology trade show in Atlantic Canada will be held at the Moncton Coliseum.

www.mcee.ca

www.meetshow.ca

CIPH Annual Business Conference June 27-29

Ventilation 2021 August 15-18

CIPHEX West 2021 November 3-4

The networking event for the Canadian plumbing and heating industry will be held at the Algonquin Resort in St. Andrews, New Brunswick.

Held every three years, the 13th International Industrial Ventilation Conference for Contaminant Control is taking place in Toronto at the Sheraton City Centre.

www.ciph.com

www.ashrae.org/conferences

Western Canada’s plumbing, hydronics, heating, ventilation, air conditioning, refrigeration and water treatment show is being held at the Pacific National Exhibition in Vancouver.

ish.messefrankfurt.com

www.ciphexwest.ca

Planning an event?

Be sure to let us know. Send the details to dpicklyk@hpacmag.com

62

HPAC | OCTOBER 2020

HPACMAG.COM

Help Keep Your Contractor Customers Safe!

HANDSAN SANITIZER FOR SALE IN CANADA MEETS HEALTH CANADA’S REQUIREMENTS

(Natural Products Number) NPN 80098253

4’8” FT

HANDSAN DISPENSERS ➢ Touchless

➢ Bulk Refillable Reservoir ➢ Robust Internal Mechanism ➢ 1000ml Capacity ➢ Battery Operated ➢ Infrared Auto Sensing ➢ Keyed Access ➢ CE CertifiedLOGO AT NO EXTRA COST

1 FT

1’2” FT

Visit us at our website www.chemfax.com Toll Free: 1-855-887-2055

Proudly Canadian since 1972

Smarter Measurement.

Faster Results.

Testo measurement instruments for combustion analysis, heating systems and heat pumps.

For more info visit www.testo.com/en-US/heating-2020