Manual de ensamble de un computador ing

Page 1




Manual of assemble of the computer

Tatiana Andrea Méndez Perea Fabian Eduardo Oliva Amezquita Support of Systems, Group. 02N08


TABLE OF CONTENT It assemble of computer Start of assemble 1. Elements of the tower 2. Entry of the source to be able to to the cabinet 3. It adjust of the source to be able to 4. Entry of the memory RAM 5. It adjust of the memory RAM 6. Lace of the processor 7. Application of cream disipadora 8. Adjust of the processor 9. Implementation of disipador 10. Connection of the disipador 11. Incrustaciรณn Of the battery 12. Lace of the Board to the carcasa of the tower 13. It adjust of the Board 14. Installation of card of network 15. It adjust of card of network 16. Adherencia Of hard disk 17. It adjust of hard disk 18. Installation of optical Unit of CD-RW or DVD 19. It adjust of the optical unit of CD-RW or DVD 20. Lace of unit of diskette 21. It adjust of unit of diskette 22. Visualisation of Units of storage 23. Connection of Molex Main 24. Connection of wire Floppy 25. Connection of wire Sata 26. Connection of Molex D 27. Connection of Molex flat 28. Connection of pilots of lit 29. Closing and adjust of cabinet


It ASSEMBLE OF COMPUTER It is important to take into account that an assemble is the union of two or more parts between yes to form a group or complete subset, therefore, an assemble of computer consists of the unification of all his internal and external components that in group offer operation to the device. Start of assemble: 1. Elements of the tower:

To initiate with the assemble have to have clear that each part has to have gone through the owed maintenance of cleaning and be in optimum conditions for his operation.

Go back to the table of content


2. Entry of the source to be able to to the cabinet:

The first is to have the carcasa of the tower without the cover and put it in shape horizontal so that it remain us free the access to the place of the source to be able to.

We take the source to be able to and situate it with the table of characteristics looking upwards and fitting it in the left inferior part, as it shows in the image.


Go back to the table of content

3. It adjust of the source to be able to:

Afterwards we will need four screws that anchored the source of power with the carcasa of the tower.


These screws will be inserted in the four holes that find in the corners of the source, con a totornillador will proceed to incrustarlos with the purpose to keep to the component adhered to the cabinet.

Go back to the table of content

4. Entry of the memorĂ­a Ram:

On the board find located the slots of the memory RAM, by what will continue to install them in the same.


5. It adjust of the memory Ram:

Andstas slots have some teeth that fit perfectly with the Ram, so when fittingthe, will take l ors safe that are situated to the extremes and will go up them until they ensure the memory to the mechanism.

Go back to the table of content

6. Lace of the processor:

To fit the process in the socket will verify that in one of the corners of the processor there is a drawing of a triangulo, was has to be equally reflected in the socket for like this match it and fit it, although in some other cases, can observe that the number of pines of each corner coincide with the number of apertures of the socket.


7. Application of cream disipadora:

When entering the processor proceed to apply the cream disipadora on of this, it is necessary to take into account that only we will apply the necessary quantity to cover the surface the processor.

8. Adjust of the processor:

Go back to the table of content

We take the crowbar or sure of the socket and go down it until it ensure entirely, before this have to check that our procesador fit perfectly sรณthe by caution.


9. Implementation of the disipador:

Now, we will continue with the disipador, are inserts on of the procesador, depending of the case it is necessary atornillar the disipador to the Board, or simply is necessary to turn some insurances, in this case have to fit a crowbar and anchor it just across the processor to the Board.

10. Connection of the disipador:

Go back to the table of content

Afterwards we will take the wire and will do the connection to the Board. The slot to fit will have four pines that insert properly to the connector of the disipador.


11. IncrustaciĂłn Of the battery:

Some Board already have installed the battery of 3V, in case that no, simply will take the battery, will situate it so that the facecterĂ­sticas are upwards and will push downwards softly until lace.

12. Lace of the Board to the carcasa of the tower: Go back to the table of content

To make the installation of the Board in the carcasa of the tower, have to take into account the situation of lace entrand the card mother and the carcasa since they exist apertures or spaces in which they enter properly the external ports.


13. It adjust of the Board:

To ensure Board to the carcasa will need six screws.

Go back to the table of content

These screws enter in orifices that are distributed in all the Board, suggests not applying so much strength to the atornillar as this could damage the Board.


14. Installation of card of network:

Now we will proceed to install the card of interface of network, this installs in one of the slots of expansion distributed in the Board, the identification of the suitable slot depends on the similar characteristics to the card and to the aperture of the slot.

15. It adjust of card of network:

Go back to the table of content


To ensure this card of interface of network, will need a screw that ancharรก to the carcasa by means of a screwdriver.

16. Adherencia Of hard disk:

To make the installation of the hard disk is necessary to take the frontal cabinet and adhere it in the space or corresponding tray to was. The suitable position corresponds to leave the ports of connection looking did the Board and the tablet of circuits looking did down.

17. It adjust of hard disk: Volver a la tabla de contenido


To ensure the hard disk, will need two screws that will go situated to the sides of the same and afterwards with an atornillador will proceed to adjust.

18. Installation of optical Unit of CD-RW or DVD:

To insert the unit of CD-RW or DVD will situate us in the part forntal of the tower and by the upper aperture will enter the component so that the ports of connection remain in sense of the board.

Go back tounit the table content or DVD: 19. It adjust of the optical of of CD-RW

Volver a la tabla de contenido


To ensure the unit of CD-RW or DVD will need two screws that will go situated to the sides of the same, and atornillarlos with an atornillador.

20. Lace of unit of diskette:

Followed of this, will fit the unit of diskette making the same procedure that with the unit optica or of CD-RW / DVD.

21. It adjust of unit of disquandyou: Go back to the table of content


To ensure the unit of diskette will need two screws that will go situated to the sides of the same, and atornillarlos with an atornillador.

22. Visualisation of Units of storage:

At the end, so much the unit CD-RW/ DVD, The unit of diskette and the hard disk remained simultaneously ensured.

23. Connection of Molex Main: Go back to the table of content


For the connection of the wires, have to ensure us to do coincide the Pin 1 with the Pin 1 when connecting thec ables to the devices.

24. Connection of wire Floppy:

We connect the wire Floppy and the wire Sata, these will be the connectors of the units and the hard disk.

25. Connection of wire Sata:

Go back to the table of content

The wire Sata connects to the unit CD-RW/ DVD and to the hard disk.


26. Connection of Molex D:

The Molex D enters in the slot so much of the unit CD-RW/ DVD as in the hard disk.

Go backflat: to the table of content 27. Connection of Molex

The Molex Flat will enter it in the unit of diskette.


28. Connection of pilots of lit:

When finalising remained us only the connection of the last wires that are the pilots of lit of the tower.

These pilots have situated in the lateral part of each wire, and Go his backnames to the table of content situate them with the Board the one who has exactly the same names.


29. Closing and adjust of cabinet:

Now we take you cover them of the tower, and plant them to both sides, when finalising will use four screws and will ensure them to the tower.

Only it remains us situate the peripherals of exit in each port, join it to a screen and having an installed operating system begin to use our computer. Go back to the table of content


Turn static files into dynamic content formats.

Create a flipbook
Issuu converts static files into: digital portfolios, online yearbooks, online catalogs, digital photo albums and more. Sign up and create your flipbook.