Cat dlrntwrksgntechspecs by Patrick Young

Primary Dealer Network Sign Family - Technical Specifications 95% Final Draft 10 July 2012

Prepared by:

BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Table of Contents Sign Code

Description

Sheet #

Performance Requirements and General Conditions

3-4

DSP Single Pole Pylon, Full Mold DSP Single Pole Pylon, Partial Mold (logo only) DSPC Single Pole Pylon, No Mold Face DSP Single Pole Sky Pylon, Flex Face DD Double Pole Pylon, Full Mold DDP Double Pole Pylon, Partial Mold (logo only) DDPC Double Pole Pylon, No Mold Face DDP Double Pole Sky Pylon, Flex Face Pole and Monument Signs - Typical Section Details

5 6 7 8 9 10 11 12 13

MON Monolith, Full Mold MON Monolith, Partial Mold (logo only) MONC Monolith, No Mold Face MONF Monolith, Hard/Flat Face Monolith - Typical Section Details

14 15 16 17 18

GDM GDM GDMC GDMF SFW SFW SFW SFWC SFWX SFWF DIR DIRM WAL/WALH

19 20 21 22 23 24 25 26 27 28 29 30 31

Monument, Full Mold Monument, Partial Mold (logo only) Monument, No Mold Face Monument, Hard/Flat Face Wall Sign, Full Mold Wall Sign, Partial Mold (logo only) Wall Sign, Curved Flex Face Wall Sign, No Mold Face Wall Sign, Flat Flex Face Wall Sign, Hard/Flat Face Directional Signs Directional Monolith Information Sign

Appendix - Master Signage Matrix

ÂŠ 2012 Caterpillar Inc. All rights reserved. All ideas, designs, arrangements and plans indicated or presented by these drawings are owned by and are the property of the Owner, and were created, evolved and developed for the use on and in connection with the specific project. None of such ideas, designs, arrangements or plans shall be used by or disclosed to any person, firm, or corporation for any purpose whatsoever without the written permission of the Owner. The Owner may have additional requirements or restrictions for which the Contractor is also responsible. The acceptance of these drawings by vendor, bidders, fabricators, or Contractors and their agents constitutes agreement to the following. These design intent drawings are for the sole purpose of design intent only and not intended for construction purposes. Resulting working drawings, shop drawings and contract documents including permit documents are the sole responsibility of the Contractor in every respect.

BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

32-34

Drawing Title: Table of Contents Drawn by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

Performance Requirements & General Conditions The ‘Primary Cat® Dealer Network Signage Technical Specificationss’ drawings are solely intended for purposes of explaining design techniques and are not intended for construction purposes. Resulting working/engineering/shop drawings and contract documents are the sole responsibility of the sign contractor/manufacturer/fabricator/ installer in every respect. Caterpillar Global Brand Management (GBM) shall review resulting shop drawings for conformance with general design intent. Fabrication of signs shall not commence until GBM has reviewed and approved all applicable shop drawings. GBM is not responsible for any physical signs resulting from the contractors shop drawings. The sign contractor/manufacturer/fabricator/installer shall be responsible for the quality and delivery of all materials and workmanship, including the materials and workmanship of firms or individuals who act as his or her sub-contractor. The sign contractor/manufacturer/fabricator/installer shall be responsible for providing subcontractors with complete and up-to-date drawings, performance and material requirements, graphics schedules, requisite artwork and other information as issued or referred to herein. Proposals from the manufacturer or installer to increase efficiency, performance or value are welcomed with drawings, for discussion with and approval from GBM.

Quality Assurance Quality of Workmanship: The contractor shall be responsible for the quality and delivery of all materials and workmanship required to execute the contract, including the materials and workmanship of any firms or individuals who act as his or her sub-contractors. Performance: The contractor shall base his or her proposal on the performance of all services, including all labor, material and equipment required to fabricate and install the specified work within the time frame agreed by the contractor and the end customer (most often the Cat dealer). Dimensioning: Written dimensions supersede scale. This document is meant to be printed on an 11” x17” format. Scales are provided as a guide to establish proportion only. Execution: The contractor shall notify GBM of any discrepancies in the drawings or message schedule, in field dimensions or conditions, and/or changes required in construction details. Problems such as messages that are too long to fit into the required formats, difficulty in reproducing logo or logotype components accurately, etc., must be brought to GBM’s attention prior to execution. The contractor shall not resolve any discrepancies without consulting GBM. Artwork: GBM is the sole provider of the Cat Dealer lockup and any other electronic artwork required by the contractor, such as symbols or custom designed graphic components (e.g, logos, logo types, arrows or patterns). Artwork will be provided in Adobe Illustrator CS (.ai) or EPS (.eps) formats. All artwork enlargements and reductions are the responsibility of the contractor. GBM cannot provide copies of licensed fonts. Dealer Lockup The Cat® logo must be used with the primary dealer’s name/mark as established in the Cat Dealer lockup (see example). The lockups are created, approved and maintained by GBM in conjunction with each primary dealer. The use of the Cat logo alone by dealers, their representatives or others is not permitted.

© 2012 Caterpillar Inc. All rights reserved. All ideas, designs, arrangements and plans indicated or presented by these drawings are owned by and are the property of the Owner, and were created, evolved and developed for the use on and in connection with the specific project. None of such ideas, designs, arrangements or plans shall be used by or disclosed to any person, firm, or corporation for any purpose whatsoever without the written permission of the Owner. The Owner may have additional requirements or restrictions for which the Contractor is also responsible. The acceptance of these drawings by vendor, bidders, fabricators, or Contractors and their agents constitutes agreement to the following. These design intent drawings are for the sole purpose of design intent only and not intended for construction purposes. Resulting working drawings, shop drawings and contract documents including permit documents are the sole responsibility of the Contractor in every respect.

The official Cat Dealer lockup shall be provided upon request to all suppliers by GBM in vector format. No recreation or alteration of the dealer lockup artwork is allowed. If you have questions regarding the use of Caterpillar trademarks, the content of this document or require approved vector artwork for dealer lockups, please contact: Corporate and Dealer Identity Help Desk Toll-free: 1.800.566.7782 U.S. tel.: +1.309.675.5135 Tieline: 7.725.5135 Email: brand@cat.com Website: https://brand.cat.com UL Compliance: Complete UL or approved nationally recognized testing agency compliance, as required is the responsibility of the contractor. Contractor shall provide lighting fixtures and electrical components that meet all UL testing lab requirements for safety, operation and construction. Fixtures and components must be UL-labeled and listed, and shall indicate locations and electrical service required for review by the dealer owner and GBM unless noted otherwise. Contractor is responsible for all final electrical connections. Light Emission: All lighting fixtures/sources shall emit a color balanced, consistent and uniform light with no browning, flickering, haloing or any other uneven effect. Electrical Hardware: All transformers, LED power supplies and electrical hardware shall be concealed, non audible and non-visible to pedestrians and vehicular traffic. Provide disconnect switch if required by governing agencies. Labeling: There shall be no visible labels, manufacturer’s or otherwise, code permitting, on the completed signs or other objects. If labels are required, a sample label and intended location along with an explanation of the requirement must be submitted to GBM for review prior to applications and/or installation. Stock: All materials, hardware, electrical components, finishes, etc. used to fabricate any and all components shall be new (not previously used or operated in any other application), be from the most recent manufacturer’s run/supply, and appropriately matched to the service conditions required of the site.

Submittals

Finishes

Shop Drawings: The contractor shall submit detailed shop drawings to GBM and one (1) reproducible set of plans, plus one (1) set of prints for review prior to production. These drawings are to show/indicate all materials, finishes, construction details, lighting requirements, installation details, artwork and structure, including locations of all material seams (finished and unfinished). Shop drawings and data shall be reviewed by GBM. The contractor shall make all corrections required and resubmit for final review. Final reviewed shop drawings noted “No Exceptions Taken” or “Exceptions as Noted” must be received from GBM before production starts.

Colors and Surface Textures: All colors shall match exactly the color and finish requirements provided by GBM. For exposed signs, materials with applied colors or other characteristics related to appearance, the contractor shall provide color matches indicated, or if not indicated, as selected and reviewed by GBM.

Shop drawings will be reviewed for compliance with design intent only. The contractor is responsible for engineering each object to meet all load and wind requirements with stamped drawings and calculations by certified engineers. The contractor is responsible for all other aspects of fabrication including engineering, procedure, installation techniques and performance as well as coordination with site conditions and related trades. Specific Samples: The contractor shall submit a minimum of two (2) samples (minimum size 6” x 6” or as requested by GBM) of each color and finish on the specified materials. Samples must be submitted in a time frame allowable for review, multiple adjustments and approval without delay to the project. GBM will review samples for color, texture and aesthetic compatibility with existing or adjacent materials. Compliance with all other requirements is the exclusive responsibility of the contractor. When specified, furnish full-size samples of objects, partial objects, and/or materials. Resubmit samples if requested until required sheen, color, texture, and compliance with fabricator performance and material requirements is accepted. Structure: Design installation, internal structure, mounting assemblies and foundations are done by contractor. The contractor shall submit engineering drawings to customers, incorporating an adequate foundation and/or mounting structure for all sign components to meet all load and wind requirements and given site conditions. The contractor shall, at his or her expense, submit calculations, sealed by certified engineers registered in the state of final installation for all structure members including foundations, for customers’ review.

Surface Preparation: All surfaces shall be thoroughly cleaned and free from dust, dirt, rust, scales, mill scales, oil, greasy materials or residue from cleaning. All coatings shall be applied in strict accordance with the manufacturer’s recommendations. All paint products shall conform to local (site) codes. All finishes shall present a uniform opaque color appearance unless specifically indicated otherwise by GBM. Paint Finishes: Ferrous surfaces: using Matthews paint products, finish with one (1) coat 74- 734 and 74-735 metal pretreat @ .25 mils DFT, one (1) coat Matthews acrylic polyurethane 1.0 mil DFT (min.), or an approved equivalent. Observe designer’s specifications regarding specularity (matte to gloss). Aluminum Using Matthews paint products, finish with one (1) coat 74-734 and 74-735 metal pretreat at .25 mils DFT or one (1) coat 74-793 spray bond at .15 to .25 mils DFT and one (1) coat Matthews acrylic polyurethane 1.0 mil DFT (min.), or an approved equivalent. All plastic to be paint finish according to paint manufacturer’s specifications. Application: All applications of color/coatings are to be equal and of consistent cover with no streaking, spotting, gradation or other variations within and from each similar application. Ultraviolet/Fading Protection: Contractor shall utilize materials, coatings and processes to minimize as much as possible any noticeable fading of pigmented coatings.

Testing: An independent testing lab will be hired and secured by the contractor to conduct inspection and material testing as required. The contractor may not proceed with the work until unsatisfactory conditions have been corrected in an acceptable manner by GBM. Lamp Service: The contractor shall provide the dealer with complete lamp replacement information, brand, type, wattage, color, etc. for all lighted components. This information shall be in a typewritten format (8-1/2” x 11”) and shall indicate at least one (1) local (site) supplier. Maintenance: The contractor shall provide customers with complete finish/component care instructions as specified by the manufacturer for on-going cosmetic cleaning and maintenance. Three sets are to be submitted in an 8-1/2” x 11” three-ring binder. Turn over to customer, one unopened gallon of each color/finish used on the project clearly marked with complete specification and color reference.

BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

Drawing Title: Performance Specificatios and General Conditions Drawn by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

Performance Requirements & General Conditions Material

Fabrication

Cleaning, Protection and Warranties

Acrylic Color Translucent Sheet: Where sheet material is indicated as “color” provide color translucent sheet of density required to produce uniform brightness without halo-like effect. Material provided shall be appropriately matched to the intended permanent field conditions.

Illumination: Illuminate units in the manner indicated using the manufacturer’s standard lighting components including: fluorescent, fixtures, power supplies, transformers, ballasts, insulators and other components. Make provisions for servicing and for concealed connections to the building system. Coordinate all electrical components with those of the power supply provided.

All items to be installed by the contractor shall be left in a clean and as-new condition. Upon completion of the installation, clean all soiled surfaces and touch up all finishes in accordance with the manufacturer’s instructions. All debris and packaging material shall be removed and disposed of in a legal manner. The protective masking of the plastic surface shall be removed by the contractor upon completion of installation. All excavation and site work shall be returned to its original grade configuration after contract items are installed.

Aluminum Sheet: Provide aluminum sheet for alloy and temper recommended by the aluminum producer for finished for the type of use and finish indicated and with not less than the strength and durability properties specified in ASTM B109 for 5005-H15. Aluminum Extrusions: Provide aluminum extrusions of alloy and temper recommended by the aluminum producer or finisher for the type of use and finish indicated and with not less than the strength and durability properties specified in ASTM B-221 for 6063-T5. Structural Steel: Provide internal structural steel as required to meet the requirements of the permanent installation. Fasteners: Unless otherwise indicated, provide concealed fasteners fabricated from metals that are non-corrosive to either the sign material or the mounting surface. Electrical/Lamps: Provide new electrical components and respective lamps, for easy repair or replacement from local available stock (24 hr. max. turn-around). Vinyl Machine Cut Copy/Graphics: Vinyl machine-cut copy and/or graphics shall be of 3M Scotchcal brand film or approved equal. Paint: Paint shall be contractor’s highest grade for best ultraviolet light resistance, weatherability and overall longevity of finish and color. Where possible, use water based, 100% solids, high performance acrylic instead of solvent-based paints. If solvent-based paint must be used, use products that are low-VOC (<380 g/l) and <1% aromatic hydrocarbons by weight. Paint shall have a written warranty against premature fading and be approved by GBM prior to construction.

Sign/Cabinet: Details shown on drawings shall be followed for exterior appearance. Structural design shall utilize unitized, self-supporting framing. Fabricate cabinet, exposed faces and graphic devices to size and styles indicated and produce surfaces free from oil canning, warping, distortion or any other irregularities or inconsistencies. Include internal bracing for stability and attachment of mounting accessories, as required. Contractor may change interior construction shown on the details to conform with specific contractor’s shop practices. However, these changes must be submitted as part of the shop drawings and be reviewed and accepted by GBM prior to fabrication.

Finish Surfaces: All units shall be warranteed in writing by the contractor for a period of no less than three (3) years from the date of customer’s acceptance. All finishes (except large format computer output) are to be warranteed for three (3) years from the date of customer’s acceptance. There shall be: 1. No delamination or any portion of the object, including vinyl graphics or copy. 2. No cupping, warping or dishing.

Fastening: Fasteners on all visible surfaces shall not be exposed, except where noted. Surfaces shall not be penetrated during fabrication or installation, except where noted. Surfaces shall not be deformed, distorted or discolored by attachment of concealed fasteners. All fasteners shall be resistant to oxidation or other corrosiveaction completely through their cross sections. Work shall be secured with fasteners of the same metal, color and finish, same as the component they secure and where they are visible. Fasteners shall be utilized in strict accordance with their manufacturer’s specifications, directions and recommendations.

3. No bubbling, crazing, chalking, rusting or other disintegration of surfaces, messages or edge finishes.

Aluminum Sheet: Shall not be less than 0.125” thick unless noted otherwise. Fabricate by the HELIARC or MIG welding process with all visible seams continuous welded, filled and ground smooth, unless the seam occurs along a color break. Then a clean butt joint with concealed backing channel and plug weld is finished to match surrounding finish. All blinds, curves and folds are to be geometrically correct, and produced by consistent mechanical methods unless approved otherwise by GBM

7. No fading of colors when matched against a sample of the original color and material.

Jointing and Brake Forming: All sheet material shall have brake formed edges with radiuses not greater than sheet thickness unless otherwise specified. Adjacent stock shall have edges of similar radiuses.

4. No corrosion developing beneath the paint surface of the support system, except as the result of obvious vandalism. 5. No corrosion of fasteners. 6. No movement of objects from their foundations. The objects must remain true and plumb on their foundations, except when obvious post-installation external damage has occurred.

8. No variation of any other performance stated by GBM on the drawings or in the fabricator performance and material requirements. 9. No visible corrosive run-off or staining (e.g., rust). Structural/Components: Contractor shall provide customer’s with three (3) copies of the written warrant prior to installation guaranteeing to correct, to customer’s satisfaction, at contractor’s sole expense, all defects in fabrication and installation of work for a period of one (1) year after the customer’s acceptance of completed installation. External Lamps: All lamps shall be warranteed against failure for 90 days, and all ballasts for one (1) year. In the event of failure within specified times, these items are to be replaced by contractor at their sole expense. Lamp Service: The contractor shall provide customers with three (3) copies and complete lamp replacement information, brand, type, wattage, color, etc., for all lighted components. This information shall be in a typewritten format (8-1/2” x 11”) and shall indicate at least one (1) local supplier. Lamps must comply with all local, state and federal regulations. Maintenance: The contractor shall provide to customers, three (3) copies each of complete finish/ component care instructions as specified by the manufacturer for ongoing cosmetic cleaning and maintenance. These are to be submitted in a three-ring binder. Contractor to ensure signs, LED, lamps and electrical components etc. are easily accessible for maintenance. The contractor shall have total and complete responsibility for the security of all equipment, materials and sign components until reviewed and accepted by customer.

BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

Drawing Title: Performance Specifications & General Conditions Drawn by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

DSP - Single Pole Pylon, Full Mold Standard

Dimensions (ft-in/mm) A 20’-0”/6096 15’-0”/4572

B 16’-0”/4876 12’-0”/3658

1 C 4’-0”/1219 3’-0”/914

R (radius)

D 2’-31/2”/698 2’-1”/635

Typical Specifications

Radius Dimensions Code R DSP-03 66’-31/8”/20190 mm DSP-02 38’-1013/16”/11858 mm

Plan View

Scale: 3/16" = 1' - 0"

Perspective Scale: NTS

Cat Sign Face, Full Mold

White polycarbonate/acrylic, vacuum formed, painted black. Prior to applying black paint, mask Cat logo to expose white. Apply translucent yellow vinyl on Cat “triangle” accordingly.

1 13

Dealer Name Face, Full Mold - Returns Only

Custom yellow vacuumed formed polycarbonate/acrylic, returns (sides) only. Opaque black vinyl dealer name applied in accordance with approved GBM Dealer lockup.

Sign Cabinet

Illumination

DSP-03

Structural metal frame with manufactured aluminum shell, painted. Provide maintenance access through one face.

Code DSP-03 DSP-02

This single pole pylon is made with full mold faces. Both CAT Sign Face and Dealer Name Face have molded returns. The Cat logo is molded into the black side face, and the Dealer name is not. The two faces are mechanically fastened together. It is internally illuminated.

Use Voltarc TriLight Max T8 long life lamps with Kulka lampholder to ensure even quality lumens across entire sign face. For locations that reach temperatures below zero Celsius (32 Fahrenheit), use the Voltarc TriLight max thermal lamp. All electrical to be in accordance with applicable codes.

5 13

Pole

Engineered structural steel mounting pole with stacked tube dimension to achieve height. Painted semi-gloss black.

Base

Foundation

Engineered structural steel base-plate, painted black semi-gloss, mechanically fastened to foundation. Exposed fasteners painted black semi-gloss post installation.

DSP-02

Engineered rebar and concrete foundation in accordance with applicable codes and wind load requirements. Fabricator to ensure excess dirt removal and to grade and finish smooth post installation. Contractor to supply mounting bolts and bolt pattern to their foundations sub-contractor.

Materials

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

Sign Faces [TBC]

Vinyl

• 3M - yellow translucent #3630-125 • or approved equivalent

Paint - Special Color Match

Match yellow and black paints to the materials being used for the sign (e.g., polycarbonate/acrylic, vinyl). Examples of acceptable paint includes Akzo SIGN 10467 semi-gloss custom yellow and 80314 satin black. Contact: Corporate and Dealer Identity Help Desk Toll-free: 1.800.566.7782 U.S. tel.: +1.309.675.5135 Tieline: 7.725.5135 Email: brand@cat.com Website: https://brand.cat.com © 2012 Caterpillar Inc. All rights reserved. All ideas, designs, arrangements and plans indicated or presented by these drawings are owned by and are the property of the Owner, and were created, evolved and developed for the use on and in connection with the specific project. None of such ideas, designs, arrangements or plans shall be used by or disclosed to any person, firm, or corporation for any purpose whatsoever without the written permission of the Owner. The Owner may have additional requirements or restrictions for which the Contractor is also responsible. The acceptance of these drawings by vendor, bidders, fabricators, or Contractors and their agents constitutes agreement to the following. These design intent drawings are for the sole purpose of design intent only and not intended for construction purposes. Resulting working drawings, shop drawings and contract documents including permit documents are the sole responsibility of the Contractor in every respect.

DSP - Single Pole Pylon, Full Mold Face - Elevation Scale: 1/4" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: 1/4" = 1' - 0"

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

DSP, Full Mold - Sizes Scale: 1/4" = 1' - 0"

Drawing Title: DSP - Single Pole Pylon, Full Mold Drawn by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

DSP - Single Pole Pylon, Partial Mold (logo only) Standard

Dimensions (ft-in/mm) A 30’-0”/9144 25’-0”/7620

B 24’-0”/7315 20’-0”/6096

C 6’-0“/1829 5’-0“/1524

Typical Specifications Cat Sign Face, Partial Mold (logo only)

Dealer Name Face, Curved, No Mold

Sign Cabinet

Illumination

R (radius)

Radius Dimensions Code R DSP-05 118’-71/8”/36147 mm DSP-04 116’-51/4”/42195 mm(?)

White polycarbonate/acrylic, curved but not molded, painted black. Prior to applying black paint, mask Cat logo to expose white. Apply translucent yellow vinyl on Cat “triangle” accordingly.

Plan View Scale: 3/16" = 1' - 0"

Perspective Scale: NTS

C DSP-05

Custom yellow vacuumed formed polycarbonate/acrylic, returns (sides) only. Opaque black vinyl dealer name applied in accordance with approved GBM Dealer lockup.

D 2’-63/4”/781 2’-31/2”/698

Structural metal frame with manufactured aluminum shell, painted. Provide maintenance access through one face.

DSP-04

Pole

Base

Foundation

2 13

6 13

3 4

Engineered structural steel mounting pole with stacked tube dimension to achieve height. Painted semi-gloss black.

Code DSP-05 DSP-04

The single pole pylon is made with a partial mold face on the Cat logo only, and has no returns. The CAT Sign Face and Dealer Name Face are two separate pieces that are joined by an “H” channel. It is internally illuminated.

Engineered structural steel base-plate, painted black semi-gloss, mechanically fastened to foundation. Exposed fasteners painted black semi-gloss post installation. Engineered rebar and concrete foundation in accordance with applicable codes and wind load requirements. Fabricator to ensure excess dirt removal and to grade and finish smooth post installation. Contractor to supply mounting bolts and bolt pattern to their foundations sub-contractor.

Materials

Sign Faces [TBC]

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

Vinyl

• 3M - yellow translucent #3630-125 • or approved equivalent

Paint - Special Color Match

DSP - Single Pole Pylon, Partial Mold Face - Elevation Scale: 3/16" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: 3/16" = 1' - 0"

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

DSP, Partial Mold - Sizes Scale: 3/16" = 1' - 0"

Drawing Title: DSP - Single Pole Pylon, Partial Mold Drawn by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

DSPC - Single Pole Pylon, No Mold Face Standard, New (2012)

Dimensions (ft-in/mm) Code DSPC-05 DSPC-04 DSPC-03 DSPC-02

A 30’-0”/9144 25’-0”/7620 20’-0”/6096 15’-0”/4572

B 24’-0”/7315 20’-0”/6096 16’-0”/4876 12’-0”/3658

1 C 6’-0“/1829 5’-0“/1524 4’-0”/1219 3’-0”/914

D 2’-63/4”/781 2’-31/2”/698 2’-31/2”/698 2’-1”/635

Typical Specifications

R (radius)

Radius Dimensions Code R DSPC-05 138’-51/4”/42195 mm DSPC-04 118’-71/8”/36147 mm

DSPC-03 DSPC-02

Plan View Scale: 3/16" = 1' - 0"

Cat Sign Face, No Mold

116’-6”/35510 mm (?) 66’-31/8”/20190 mm

Perspective Scale: NTS

White polycarbonate/acrylic, curved but not molded (vacuum formed). Black vinyl knocked out for entire logo. Apply yellow triangle behind the black on pre-mask.

Dealer Name Face, No Mold

Sign Cabinet

Illumination

DSPC-05

Custom yellow polycarbonate/acrylic with applied opaque black vinyl dealer name applied in accordance with approved GBM Dealer lockup.

DSPC-04

Structural metal frame with manufactured aluminum shell, painted. Provide maintenance access through one face. Use Voltarc TriLight Max T8 long life lamps with Kulka lampholder to ensure even quality lumens across entire sign face. For locations that reach temperatures below zero Celsius (32 Fahrenheit), use the Voltarc TriLight max thermal lamp. All electrical to be in accordance with applicable codes.

Pole

Base

Foundation

4 13

6 13

1 DSPC-03

3 4

Engineered structural steel mounting pole with stacked tube dimension to achieve height. Painted semi-gloss black.

This single pole pylon has the curved sign face of standard signs, and does not use molding (vacuum forming). The CAT Sign Face and Dealer Name Face are two separate pieces that are joined by an “H” channel. It is internally illuminated.

Engineered structural steel base-plate, painted black semi-gloss, mechanically fastened to foundation. Exposed fasteners painted black semi-gloss post installation.

DSPC-02

Materials

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

Sign Faces [TBC]

Vinyl

• 3M - yellow translucent #3630-125 / black #7725-12 • or approved equivalent

Paint - Special Color Match

DSPC - Single Pole Pylon, No Mold Face - Elevation Scale: 3/16" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: 3/16" = 1' - 0"

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

DSPC, No Mold - Sizes Scale: 3/16" = 1' - 0"

Drawing Title: DSPC - Single Pole Pylon, No Mold Face Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

DSP - Single Pole Sky Pylon, Flex Face Standard This single pole sky pylon has a flex face that is framed with a manufactured aluminum mechanical tensioning system. It is internally illuminated.

Dimensions (ft-in/mm) A 50’-0”/15240 40’-0”/12192 35’-0”/10668

B 36’-0”/10973 32’-0”/9754 28’-0”/8534

C 9’-0“/2743 8’-0”/2438 7’-0”/2133

D 4’-51/2”/1359 3’-11”/1194 3’-81/2”/1130

Typical Specifications

Flex Sign Face

Plan View Scale: NTS

3M Panagraphics 3 with custom yellow and black vinyl applied. Black vinyl is knocked out to reveal white letters behind. Add custom yellow vinyl behind black for triangle.

Perspective Scale: NTS

B C DSP-08

Sign Cabinet

Structural metal frame with manufactured aluminum shell, painted. Provide a manufactured extruded aluminum mechanical tensioning system to secure flex face material to be tought, flat and true.

DSP-07

Illumination

Pole

Base

178’-0”/54254 mm 158’-29/16”/48223 mm 138’-51/4”/42196 mm

DSP-08 DSP-07 DSP-06

3 13

DSP-06

1 2

Engineered structural steel mounting pole with stacked tube dimension to achieve height. Painted semi-gloss black.

Engineered structural steel base-plate, painted black semi-gloss, mechanically fastened to foundation. Exposed fasteners painted black semi-gloss post installation.

Code DSP-08 DSP-07 DSP-06

Radius Dimensions Code R

R (radius)

Foundation

Materials

Sign Faces [TBC]

• 3M Panagraphics 3 • or approved equivalent

Vinyl

• 3M - yellow translucent #3630-125 (with opaque backer) / black #7725-12 • Arlon - yellow translucent #2500-2334E • or approved equivalent

Paint - Special Color Match

Match yellow and black paints to the materials being used for the sign. Examples of acceptable paint includes Akzo SIGN 10467 semi-gloss custom yellow and 80314 satin black. Contact: Corporate and Dealer Identity Help Desk Toll-free: 1.800.566.7782 U.S. tel.: +1.309.675.5135 Tieline: 7.725.5135 Email: brand@cat.com Website: https://brand.cat.com © 2012 Caterpillar Inc. All rights reserved. All ideas, designs, arrangements and plans indicated or presented by these drawings are owned by and are the property of the Owner, and were created, evolved and developed for the use on and in connection with the specific project. None of such ideas, designs, arrangements or plans shall be used by or disclosed to any person, firm, or corporation for any purpose whatsoever without the written permission of the Owner. The Owner may have additional requirements or restrictions for which the Contractor is also responsible. The acceptance of these drawings by vendor, bidders, fabricators, or Contractors and their agents constitutes agreement to the following. These design intent drawings are for the sole purpose of design intent only and not intended for construction purposes. Resulting working drawings, shop drawings and contract documents including permit documents are the sole responsibility of the Contractor in every respect.

DSP - Single Pole Sky Pylon, Flex Face - Elevation Scale: NTS BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: NTS

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

DSP, Flex Face - Sizes Scale: NTS

Drawing Title: DSP - Single Pole Sky Pylon, Flex Face Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

DDP - Double Pole Pylon, Full Mold Standard

Dimensions (ft-in/mm)

A B C 20’-0”/6096 16’-0”/4876 4’-0”/1219 15’-0”/4572 12’-0”/3658 3’-0”/914

Cat Sign Face, Full Mold

Plan View - Full Mold

Scale: 1/4” = 1’ - 0”

Illumination

Perspective Scale: NTS

1 13

Custom yellow vacuumed formed polycarbonate/acrylic, returns (sides) only. Opaque black vinyl dealer name applied in accordance with approved GBM Dealer lockup.

Dealer Name Face, Full Mold - Returns Only

Sign Cabinet

White polycarbonate/acrylic, vacuum formed, painted black. Prior to applying black paint, mask Cat logo to expose white. Apply translucent yellow vinyl on Cat “triangle” accordingly.

Radius Dimensions Code R DDP-03 66’-31/8”/20196 mm DDP-02 38’-1013/16”/11857 mm

C DDP-03

Structural metal frame with manufactured aluminum shell, painted. Provide maintenance access through one face.

R (radius)

E 8’-4”/2540 6’-8”/2032

Typical Specifications

5 13

Poles

Engineered structural steel mounting poles with stacked tube dimension to achieve height. Painted semi-gloss black. Round preferred, square acceptable.

Bases

Engineered structural steel base-plates, painted black semi-gloss, mechanically fastened to foundation. Exposed fasteners painted black semigloss post installation.

DDP-02

Code DDP-03 DDP-02

This double pole pylon is made with full mold faces. The CAT Sign Face and Dealer Name Face have molded returns. The Cat logo is molded into the black side face, and the Dealer name is not. The two faces are mechanically fastened together. It is internally illuminated.

Foundation

Engineered rebar and concrete foundations in accordance with applicable codes and wind load requirements. Fabricator to ensure excess dirt removal and to grade and finish smooth post installation. Contractor to supply mounting bolts and bolt pattern to the foundations sub-contractor.

Materials

Sign Faces [TBC]

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

6 7

Vinyl

• 3M - yellow translucent #3630-125 • or approved equivalent

Paint - Special Color Match

DDP - Double Pole Pylon, Full Mold Face - Elevation Scale: 1/4” = 1’ - 0” BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: 1/4” = 1’ - 0”

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

DDP, Full Mold - Sizes Scale: 1/4” = 1’ - 0”

Drawing Title: DDP - Double Pole Pylon, Full Mold Drawn by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

DDP - Double Pole Pylon, Partial Mold (logo only) Standard

Dimensions (ft-in/mm)

A B C 30’-0”/9144 24’-0”/7315 6’-0“/1829 25’-0”/7620 20’-0”/6096 5’-0“/1524

1 D E 2’-63/4”/781 12’-0”/3657 2’-31/2”/698 10’-0”/3048

Typical Specifications Cat Sign Face, Partial Mold (logo only)

2 3

Sign Cabinet

R (radius)

Plan View Scale: 3/16" = 1' - 0"

White polycarbonate/acrylic, vacuum formed, painted black. Prior to applying black paint, mask Cat logo to expose white. Apply translucent yellow vinyl on Cat “triangle” accordingly.

Dealer Name Face, No Mold

Radius Dimensions Code R DDP-05 118’-71/8”/36147 mm DDP-04 116’-5 1/4”/42195 mm(?)

Perspective Scale: NTS

C DDP-05

Custom yellow polycarbonate/acrylic with applied opaque black vinyl dealer name applied in accordance with approved GBM Dealer lockup.

Structural metal frame with manufactured aluminum shell, painted. Provide maintenance access through one face.

DDP-04

Illumination

6 13

Poles

Engineered structural steel mounting poles with stacked tube dimension if required to achieve height. Painted semi-gloss black.

Bases

Foundation

Engineered structural steel base-plates, painted black semi-gloss, mechanically fastened to foundation. Exposed fasteners painted black semigloss post installation.

2 13

Code DDP-05 DDP-04

This double pole pylon is made with a partial mold face on the Cat logo only, and has no returns. The CAT Sign Face and Dealer Name Face are two separate pieces that are joined by an “H” channel. It is internally illuminated.

Materials

Sign Faces [TBC]

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

Vinyl

• 3M - yellow translucent #3630-125 • or approved equivalent

Paint - Special Color Match

DDP - Double Pole Pylon, Partial Mold Face - Elevation Scale: 3/16" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: 3/16" = 1' - 0"

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

DDP, Partial Mold - Sizes Scale: 3/16" = 1' - 0"

Drawing Title: DDP - Double Pole Pylon, Partial Mold Drawn by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

DDPC - Double Pole Pylon, No Mold Face Standard, New (2012)

Dimensions (ft-in/mm) Code DDPC-05 DDPC-04 DDPC-03 DDPC-02

A B 30’-0”/9144 24’-0”/7315 25’-0”/7620 20’-0”/6096 20’-0”/6096 16’-0”/4876 15’-0”/4572 12’-0”/3658

C 6’-0“/1829 5’-0“/1524 4’-0”/1219 3’-0”/914

D 2’-63/4”/781 2’-31/2”/698 2’-31/2”/698 2’-1”/635

E 12’-0”/3658 10’-0”/3048 8’-4”/2540 6’-8”/2032

Typical Specifications

R (radius)

DDPC-03 DDPC-02

Plan View

Scale: 3/16" = 1' - 0"

Cat Sign Face, No Mold

Dealer Name Face, No Mold

Sign Cabinet

Illumination

116’-6”/35509 mm(?) 66’-31/8”/20196 mm

5 B

Perspective Scale: NTS

White polycarbonate/acrylic, curved but not molded (vacuum formed). Black vinyl knocked out for entire logo. Apply yellow triangle behind the black on pre-mask.

Radius Dimensions Code R DDPC-05 138’-51/4”/42195 mm DDPC-04 118’-71/8”/36147 mm

DDPC-05

Custom yellow polycarbonate/acrylic with applied opaque black vinyl dealer name applied in accordance with approved GBM Dealer lockup.

DDPC-04

Structural metal frame with manufactured aluminum shell, painted. Provide maintenance access through one face. 6 13

4 13

DDPC-03

Poles

Engineered structural steel mounting poles with stacked tube dimension if required to achieve height. Painted semi-gloss black.

Bases

Foundation

This double pole pylon has the curved sign face of standard signs , and does not use molding (vacuum formed). The CAT Sign Face and Dealer Name Face are two separate pieces. that are joined by an “H” channel. It is internally illuminated.

DDPC -02

Engineered structural steel base-plates, painted black semi-gloss, mechanically fastened to foundation. Exposed fasteners painted black semigloss post installation. Engineered rebar and concrete foundations in accordance with applicable codes and wind load requirements. Fabricator to ensure excess dirt removal and to grade and finish smooth post installation. Contractor to supply mounting bolts and bolt pattern to the foundations sub-contractor.

Materials

Sign Faces [TBC]

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

Vinyl

• 3M - yellow translucent #3630-125 / black #7725-12 • or approved equivalent

Paint - Special Color Match

DDPC - Double Pole Pylon, No Mold Face - Elevation Scale: 3/16" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: 3/16" = 1' - 0"

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

DDPC, No Mold - Sizes Scale: 3/16" = 1' - 0"

Drawing Title: DDPC - Double Pole Pylon, No Mold Face Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

DDP - Double Pole Sky Pylon, Flex Face Standard

Dimensions (ft-in/mm) A 50’-0”/15240 40’-0”/12192 35’-0”/10668

B 36’-0”/10973 32’-0”/9754 28’-0”/8534

C 9’-0“/2743 8’-0”/2438 7’-0”/2133

Typical Specifications

Flex Sign Face

Radius Dimensions Code R

R (radius)

DDP-08 DDP-07 DDP-06

Plan View

178’-0”/54254 mm 158’-29/16”/48224 mm 138’-51/4”/42196 mm

Scale: NTS

Perspective Scale: NTS

3M Panagraphics 3 with custom yellow and black vinyl applied. Black vinyl is knocked out to reveal white letters behind. Add custom yellow vinyl behind black for triangle.

C DDP-08

Sign Cabinet

Structural metal frame with manufactured aluminum shell, painted. Provide manufactured extruded aluminum mechanical tensioning system to secure flex face material to be tought and true.

D 4’-51/2”/1362 3’-11”/1193 3’-81/2”/1136

DDP-07

Illumination

3 13

Poles

Bases

Foundation

DDP-06

1 2

Engineered structural steel mounting poles with stacked tube dimension if required to achieve height. Painted semi-gloss black.

3 4

Engineered structural steel base-plates, painted black semi-gloss, mechanically fastened to foundation. Exposed fasteners painted black semigloss post installation.

4 A

Code DDP-08 DDP-07 DDP-06

This double pole sky pylon has a flex face that is framed with a manufactured aluminum mechanical tensioning system. It is internally illuminated.

Materials

Sign Faces [TBC]

• 3M Panagraphics 3 • or approved equivalent

Vinyl

• 3M - yellow translucent #3630-125 (with opaque backer) / black #7725-12 • or approved equivalent

Paint - Special Color Match

DDP - Double Pole Pylon, Flex Face - Elevation Scale: NTS BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: NTS

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

DDP, Flex Face - Sizes Scale: NTS

Drawing Title: DDP - Double Pole Sky Pylon, Flex Face Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

Pole & Monument Signs - Typical Section Details Typical Specification

Cat Sign Face

White polycarbonate/acrylic, vacuum formed, painted black. Prior to applying black paint, mask Cat logo to expose white. Apply translucent yellow vinyl on Cat “triangle” accordingly.

Dealer Name Face

Sign Cabinet

Illumination

Pole

Hinged Access

Alum.”F” retainer

Custom yellow polycarbonate/acrylic with applied opaque black vinyl dealer name applied in accordance with approved GBM Dealer lockup. Structural metal frame with manufactured aluminum shell, painted yellow. Return painted black to correspond with Cat sign face. Use Voltarc TriLight Max T8 long life lamps with Kulka lampholder to ensure even quality lumens across entire sign face. For locations that reach temperatures below zero Celsius (32 Fahrenheit), use the Voltarc TriLight max thermal lamp. All electrical to be in accordance with applicable codes.

1 2

Engineered structural steel mounting pole(s). Round perferred.

Divider bar extrusion

Continuous hinged access one side, or as required for expedient electrical service and maintainence.

Expansion and Contraction Crutch

Flex Sign Face

/4” Dia. EMT conduit with 3/4” rubber tip each end fastened to sign frame to support sign face shape through temperature cycles.

3M Panagraphics 3 with custom yellow and black vinyl applied. Black vinyl is knocked out to reveal white letters behind. Add custom yellow vinyl behind black for triangle.

Trim face flanges @ joint. Mechanically fasten together. Black caulk seam to prevent light leaks

5 7 1

Partial Mold & No Mold Section Detail @ joint btwn faces

Scale: NTS

Sign Types: DSPC, DDPC

Full Mold - Section Detail @ joint btwn faces Scale: NTS

No Mold Face - Typical Section Detail Scale: NTS

Alum.”F” retainer

SignComp 7000 Series Econoflex extrusion or approved equal.

Materials

Sign Faces [TBC]

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

Vinyl

• 3M - yellow translucent #3630-125 • or approved equivalent

Paint - Special Color Match

Sign Types: DSP-02 & 03, DDP-02 & 03, GDM-02 & 03

Sign Types: DSP-04 & 05, DDP-04 & 05, GDM-04

Full Mold Face - Typical Section Detail

Scale: NTS BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Partial Mold Face - Typical Section Detail Scale: NTS

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

Sign Types: DSP, DDP

Flex Face - Typical Section Detail Scale: NTS

Drawing Title: Pole and Monument Signs - Typical Section Details Drawn by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

MON - Monolith, Full Mold Standard

C B

This monolith is made with full mold faces. Both CAT Sign Face and Dealer Name Face have molded returns. The Cat logo is molded into the black side face, and the Dealer name is not. The two faces are mechanically fastened together. It is internally illuminated.

Dimensions (ft-in/mm)

Code A B C D E MON-300 16’-0”/4876 4’-0”/1219 5’-4“/1625 1’-6”/457 10“/253 MON-200 12’-0”/3658 3’-0”/914 4’-0”/1219 1’-11/2”/342 71/2”/190

F 10“/253 71/2”/190

E D

Radius Dimensions Code R

Typical Specifications

Dealer Name Face, Full Mold - Returns Only

Sign Cabinet

Illumination

R (radius)

Plan View Scale: 3/8" = 1' - 0" 4 18

Cat Sign Face, Full Mold

White polycarbonate/acrylic, vacuum formed, painted black. Prior to applying black paint, mask Cat logo to expose white. Apply translucent yellow vinyl on Cat “triangle” accordingly.

12’-1”/3683 mm 9’-3/4”/2762 mm

B MON-300

Custom yellow vacuumed formed polycarbonate/acrylic, returns (sides) only. Opaque black vinyl dealer name applied in accordance with approved GBM Dealer lockup.

B 8 18

Structural metal frame with manufactured aluminum shell, painted. Provide maintenance access through one face.

MON-200

Base Cover

Base

Foundation

Fabricated aluminum base cover, two piece construction. Mechanically fastened together and to base. Painted black.

2 A

MON-300 MON-200

Materials

Sign Faces [TBC]

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

1 18

Vinyl

• 3M - yellow translucent #3630-125 • or approved equivalent

6 7 F

Paint - Special Color Match

MON Monolith, Full Mold Face - Elevation

Scale: 3/8" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side View Scale: 3/8" = 1' - 0"

MON, Full Mold - Sizes Scale: 3/8" = 1' - 0"

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

Perspective Scale: NTS

Drawing Title: MON - Monolith, Full Mold Drawn by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

MON - Monolith, Partial Mold (logo only) Standard This monolith is made with a partial mold face on the CAT logo, and has no returns. The CAT Sign Face and Dealer Name Face are separate pieces that are joined by a “H” channel. It is internally illuminated.

Radius Dimensions Code R MON-500 15’-11/4”/4603 mm

Dimensions (ft-in/mm)

MON-400

Code A B C D E F MON-500 24’-0”/7315 6’-0”/1829 8’-0“/2438 2’-3”/685 1’-3“/381 1’-3“/381 MON-400 20”-0”/6096 5’-0”/1524 6’-8“/2032 1’-101/2”/571 1’-1/2“/317 1’-1/2“/317

12’-1”/3683 mm

Typical Specifications

Cat Sign Face, Partial Mold (logo only)

Dealer Name Face, No Mold

Sign Cabinet

Illumination

Base Cover

Base

Foundation

White polycarbonate/acrylic, vacuum formed, painted black. Prior to applying black paint, mask Cat logo to expose white. Apply translucent yellow vinyl on Cat “triangle” accordingly. Custom yellow polycarbonate/acrylic with applied opaque black vinyl dealer name applied in accordance with approved GBM Dealer lockup. Structural metal frame with manufactured aluminum, painted. Provide maintenance access through one face. Use Voltarc TriLight Max T8 long life lamps with Kulka lampholder to ensure even quality lumens across entire sign face. For locations that reach temperatures below zero Celsius (32 Fahrenheit), use the Voltarc TriLight max thermal lamp. All electrical to be in accordance with applicable codes. Fabricated aluminum base cover, two piece construction. Mechanically fastened together and to base. Painted black. Engineered structural steel base-plate, painted black semi-gloss, mechanically fastened to foundation. Exposed fasteners painted black semi-gloss post installation. Engineered rebar and concrete foundation in accordance with applicable codes and wind load requirements. Fabricator to ensure excess dirt removal and to grade and finish smooth post installation. Contractor to supply mounting bolts and bolt pattern to the foundations sub-contractor.

Materials

Sign Faces [TBC]

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

2 18

Vinyl

• 3M - yellow translucent #3630-125 • or approved equivalent

Paint - Special Color Match

BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

Drawing Title: MON - Monolith, Partial Mold Drawn by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

MONC - Monolith, No Mold Face Standard, New (2012) This monolith is made of the CAT Sign Face and Dealer Name Face which are two separate pieces. The two faces are joined by an “H” channel. It is internally illuminated.

Dimensions (ft-in/mm) Code

MONC-500 MONC-400 MONC-300 MONC-200

24’-0”/7315 20’-0”/6096 16’-0”/4876 12’-0”/3658

6’-0”/1829 5’-0”/1524 4’-0”/1219 3’-0”/914

8’-0“/2438 2’-3”/685 1’-3“/381 6’-8“/2032 1’-101/2”/571 1’-1/2“/317 5’-4“/1625 1’-6”/457 10“/253 4’-0”/1219 1’-11/2”/342 71/2”/190

Radius Dimensions Code R MONC-500 18’-11/4”/5518 mm MONC-400 15’-11/4”/4604 mm

MONC-300 12’-1”/3683 mm MONC-200 9’-3/4”/2762 mm

1’-3“/381 1’-1/2“/317 10“/253 71/2”/190

Typical Specifications

Cat Sign Face - No Mold

Dealer Name Face

Sign Cabinet

Illumination

Base Cover

Base

Foundation

White polycarbonate/acrylic, curved but not molded (vacuum formed). Black vinyl knocked out for entire logo. Apply yellow triangle behind the black on pre-mask. Custom yellow polycarbonate/acrylic with applied opaque black vinyl dealer name applied in accordance with approved GBM Dealer lockup. Structural metal frame with manufactured aluminum shell, painted. Provide maintenance access through one face. Use Voltarc TriLight Max T8 long life lamps with Kulka lampholder to ensure even quality lumens across entire sign face. For locations that reach temperatures below zero Celsius (32 Fahrenheit), use the Voltarc TriLight max thermal lamp. All electrical to be in accordance with applicable codes. Fabricated aluminum base cover, two piece construction. Mechanically fastened together and to base. Painted black. Engineered structural steel base-plate, painted black semi-gloss, mechanically fastened to foundation. Exposed fasteners painted black semi-gloss post installation. Engineered rebar and concrete foundation in accordance with applicable codes and wind load requirements. Fabricator to ensure excess dirt removal and to grade and finish smooth post installation. Contractor to supply mounting bolts and bolt pattern to the foundations sub-contractor.

Materials

Sign Faces [TBC]

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

2 18

Vinyl

• 3M - yellow translucent #3630-125 / black #7725-12 • or approved equivalent

Paint - Special Color Match

BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

Drawing Title: MONC - Monolith, No Mold Face Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

MONF - Monolith, Flat Face Basic, New (2012)

C B

Dimensions (ft-in/mm)

Code A B C D E MONF-500 24’-0”/7315 6’-0”/1829 8’-0“/2438 2’-3”/685 1’-3”/305 MONF-400 20’-0”/6096 5’-0”/1524 6’-8“/2032 1’-10.5”/571 1’-0”/305 MONF-300 16’-0”/4876 4’-0”/1219 5’-4“/1625 1’-6”/457 91/2”/241 MONF-200 12’-0”/3658 3’-0”/914 4’-0”/1219 1’-1.5”/342 8”/203

F 1’-3“/381 1’-0“/305 91/2”/241 8”/203

E D

This monolith is a flat metal cabinet with graphics applied to each side. It is nonilluminated. However, flood lighting from fixtures at the foot of the sign is acceptable.

Typical Specifications

Scale: 1/4" = 1' - 0" 6 18

Cat Sign Face

Paint entire sign cabinet yellow, then paint the Cat sign face area black. Apply white opaque vinyl and custom translucent yellow vinyl for the triangle (with an opaque backer film applied underneath the yellow).

Dealer Name Face

Sign Cabinet

Base Cover

Base

Foundation

B MONF-500

Opaque black vinyl dealer name applied in accordance with approved GBM Dealer lockup.

MONF-400

Structural metal frame clad with aluminum shell, finished smooth and painted yellow, then semi-gloss black. Fabricated aluminum base cover, two piece construction. Mechanically fastened together and to base. Painted semi-gloss black. Engineered structural steel base-plate, painted black semi-gloss, mechanically fastened to foundation. Exposed fasteners painted black semi-gloss post installation.

MONF-300

6 -

Plan View

MONF-200

Materials

Sign Faces

• aluminum - TBC • or approved equivalent

Vinyl

3 18

• 3M - opaque white #7725-10 / black #7725-12 • or approved equivalent

6 F

Paint - Special Color Match

Match yellow and black paints to the materials being used for the sign (e.g., aluminum, vinyl). Contact: Corporate and Dealer Identity Help Desk Toll-free: 1.800.566.7782 U.S. tel.: +1.309.675.5135 Tieline: 7.725.5135 Email: brand@cat.com Website: https://brand.cat.com © 2012 Caterpillar Inc. All rights reserved. All ideas, designs, arrangements and plans indicated or presented by these drawings are owned by and are the property of the Owner, and were created, evolved and developed for the use on and in connection with the specific project. None of such ideas, designs, arrangements or plans shall be used by or disclosed to any person, firm, or corporation for any purpose whatsoever without the written permission of the Owner. The Owner may have additional requirements or restrictions for which the Contractor is also responsible. The acceptance of these drawings by vendor, bidders, fabricators, or Contractors and their agents constitutes agreement to the following. These design intent drawings are for the sole purpose of design intent only and not intended for construction purposes. Resulting working drawings, shop drawings and contract documents including permit documents are the sole responsibility of the Contractor in every respect.

MONF Monolith, Hard/Flat Face - Elevation

Scale: 1/4" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side View Scale: 1/4" = 1' - 0"

MONF - Sizes Scale: 1/4" = 1' - 0"

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

Perspective Scale: NTS

Drawing Title: MONF - Monolith, Hard/Flat Face Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

Monolith - Typical Section Details Typical Specifications

Cat Sign Face

Dealer Name Face

Sign Frame

Illumination

Hinged Access

1 1

Trim face flanges @ joint. Mechanically fasten together.

Divider bar extrusion

Black caulk seam to prevent light leaks

Structural metal frame with manufactured aluminum, painted yellow. Return painted black to correspond with Cat sign face.

Fabricated Sign Cabinet

Metal sheet and extrusion fabricated dimensionally to retain sign faces. Paint accordingly.

Sign Cabinet

Base Cover

Metal clad sign cabinet fabricated square, flat and true. Finish smooth and paint accordingly.

Partial Mold & No Mold Section Detail @ joint btwn faces

Full Mold - Section Detail @ joint btwn faces

Fabricated aluminum base cover, two piece construction. Mechanically fastened together and to base. Painted semi-gloss black.

4 Materials

Sign Faces [TBC]

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

Full Mold - Typical Section Detail @ top of face

Partial Mold & No Mold Typical Section Detail @ top of face

Flat Face - Typical Section Detail @ top of cabinet

Vinyl

• 3M - yellow translucent #3630-125 • or approved equivalent

Paint - Special Color Match

Full Mold - Typical Section Detail @ bottom of face BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Partial Mold & No Mold Face Typical Section Detail @ bottom of face Primary Dealer Network Sign Family Technical Specifications

Client: Client:

Project:

Flat Face - Typical Section Detail @ bottom of cabinet

Drawing Title: Monolith - Typical Section Details Drawn by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

GDM - Monument, Full Mold Standard This monument is made with full mold faces. Both CAT Sign Face and Dealer Name Face have molded returns. The Cat logo is molded into the black side face, and the Dealer name is not. The two faces are mechanically fastened together. It is internally illuminated.

Dimensions (ft-in/mm)

Code A B C D R GDM-03 6’-0”/1829 16’-0”/4877 4’-0”/1219 1’-103/4”/578 38’-1013/16”/11853 mm GDM-02 5’-0”/1524 12’-0”/3658 3’-0”/914 2’-11/4”/666 66’-31/8”/20196 mm

Typical Specifications

Cat Sign Face, Full Mold

Dealer Name Face, Full Mold - Returns Only

Sign Cabinet

Illumination

Poles

2 Trim face flanges @ joint. Mechanically fasten together. Black caulk seam to prevent light leaks

Scale: NTS

D 1

1 R (radius)

Engineered structural steel mounting tubes. Painted semi-gloss black.

Bases

Engineered structural steel base-plates, painted black semi-gloss, mechanically fastened to foundation. Exposed fasteners painted black semigloss post installation.

Section Detail @ joint between faces

Plan View Scale: 1/4" = 1' - 0"

2 3

Foundation

Engineered rebar and concrete foundation in accordance with applicable codes and wind load requirements. Fabricator to ensure excess dirt removal, backfill soil around legs and finish smooth post installation. Contractor to supply mounting bolts and bolt pattern to the foundations sub-contractor.

Perspective

5 7 -

Scale: 3/16" = 1' - 0"

1 13

C GDM-03

Materials

GDM-02

Sign Faces [TBC]

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

Vinyl

• 3M - yellow translucent #3630-125 • or approved equivalent

Paint - Special Color Match

6 7

GDM Monument, Full Mold Face - Elevation

Scale: 1/4" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: 1/4" = 1' - 0"

GDM, Full Mold - Sizes Scale: 1/4" = 1' - 0"

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

Drawing Title: GDM - Monument, Full Mold Drawn by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

GDM - Monument, Partial Mold (logo only) Standard The monument is made with a partial mold face on the CAT logo only, and has no returns. The CAT Sign Face and Dealer Name Face are two separate pieces that are joined by an “H” channel. It is internally illuminated.

Dimensions (ft-in/mm)

Code A B C D GDM-04 7’-0”/2133 20’-0”/6096 5-0”/1524 2’-1/4”/666

R 66’-31/8”/20196 mm

Typical Specifications

Cat Sign Face, Partial Mold (logo only)

Dealer Name Face - No Mold

Divider bar extrusion

Sign Cabinet

Structural metal frame with manufactured aluminum, painted yellow. Return painted black to correspond with Cat sign face. Provide maintenance access through one face.

Illumination

Poles

Bases

Custom yellow polycarbonate/acrylic. Opaque black vinyl dealer name applied in accordance with approved GBM Dealer lockup.

Scale: NTS

1 R (radius)

Engineered structural steel base-plates, painted black semi-gloss, mechanically fastened to foundation. Exposed fasteners painted black semigloss post installation.

Foundation

Partial Mold & No Mold Section Detail @ joint btwn faces

White polycarbonate/acrylic, vacuum formed, painted black. Prior to applying black paint, mask Cat logo to expose white. Apply translucent yellow vinyl on Cat “triangle” accordingly.

Plan View

Scale: 3/16” = 1’ - 0”

2 3 4

7 -

Perspective Scale: NTS

2 13

C GDM-04

Materials

Sign Faces [TBC]

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

Vinyl

• 3M - yellow translucent #3630-125 • or approved equivalent

Paint - Special Color Match

6 7

GDM Monument, Partial Mold Face - Elevation

Scale: 3/16” = 1’ - 0” BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: 3/16” = 1’ - 0”

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

GDM, Partial Mold - Sizes Scale: 3/16” = 1’ - 0”"

Drawing Title: GDM - Monument, Partial Mold Drawn by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

GDMC - Monument, No Mold Face Standard, New (2012) This monolith has a face that is comprised of two pieces; the Cat Sign Face and the Dealer Name Face. The two faces are joined with an “H” channel. Internally illuminated.

Dimensions (ft-in/mm) Code GDMC-04 GDMC-03 GDMC-02

A 7’-0”/2134 6’-0”/1829 5’-0”/1524

B 20’-0”/6096 16’-0”/4877 12’-0“/3658

C 5’-0”/1524 4’-0”/1219 3’-0”/914

R 66’-31/8”/20196 mm 38’-1013/16”/11858 mm 25’-111/8”/7903 mm

Typical Specifications

Cat Sign Face, No Mold

Dealer Name Face, No Mold

Sign Cabinet

Poles

Divider bar extrusion

Structural metal frame with manufactured aluminum shell, painted yellow. One-third (1/3) of return painted black to correspond with Cat sign face. Provide maintenance access through one face.

Illumination

Engineered structural steel mounting tubes. Painted semi-gloss black.

R (radius)

Bases

Engineered structural steel base-plates, painted black semi-gloss, mechanically fastened to foundation. Exposed fasteners painted black semigloss post installation.

Scale: NTS

Partial Mold & No Mold Section Detail @ joint btwn faces

Foundation

Plan View

Scale: 3/16” = 1’ - 0”

6 -

3 4

Scale: NTS

4 13

Perspective

GDMC-04

GDMC-03

Materials

GDMC-02

Sign Faces [TBC]

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

Vinyl

• 3M - yellow translucent #3630-125 / black #7725-12 • or approved equivalent

Paint - Special Color Match

5 6 7

GDMC Monument, No Mold Face - Elevation

Scale: 3/16” = 1’ - 0” BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: 3/16” = 1’ - 0”

GDMC, No Mold Face - Sizes Scale: 3/16” = 1’ - 0”

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

Drawing Title: GDMC - Monument, No Mold Face Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

GDMF - Monument, Flat Face Basic, New (2012) This monolith is a flat faced metal cabinet with graphics applied on each side. It is nonilluminated. However, flood lighting from fixtures at the foot of the sign is acceptable.

Dimensions (ft-in/mm) Code GDMF-04 GDMF-03 GDMF-02

A 7’-0”/2134 6’-0”/1829 5’-0”/1524

B 20’-0”/6096 16’-0”/4877 12’-0”/3658

C 5’-0“/1524 4’-0”/1219 3’-0”/914

D 1’-3”/381 1’-11/2”/343 1’-0”/305

Typical Specifications

Cat Sign Face

Dealer Name Face

Sign Cabinet

Poles

Bases

Paint entire sign cabinet yellow, then paint the Cat Sign Face area black. Apply white opaque vinyl and custom translucent yellow vinyl for the triangle (with an opaque backer film applied underneath the yellow). Opaque black vinyl dealer name applied in accordance with approved GBM Dealer lockup. Structural metal frame clad with aluminum, finished smooth and painted yellow. One-third (1/3) of return painted black to correspond with Cat sign face.

Engineered structural steel mounting tubes. Painted semi-gloss black. Engineered structural steel base-plates, painted black semi-gloss, mechanically fastened to foundation. Exposed fasteners painted black semigloss post installation.

Foundation

Plan View

Scale: 3/16" = 1' - 0"

Perspective Scale: NTS

1 B

C GDMF-04

GDMF-03

GDMF-02

Materials

Paint - Special Color Match

Match yellow and black paints to the materials being used for the sign. Examples of acceptable paint includes Akzo SIGN 10467 semi-gloss custom yellow adn 80314 satin black. Contact: Corporate and Dealer Identity Help Desk Toll-free: 1.800.566.7782 U.S. tel.: +1.309.675.5135 Tieline: 7.725.5135 Email: brand@cat.com Website: https://brand.cat.com © 2012 Caterpillar Inc. All rights reserved. All ideas, designs, arrangements and plans indicated or presented by these drawings are owned by and are the property of the Owner, and were created, evolved and developed for the use on and in connection with the specific project. None of such ideas, designs, arrangements or plans shall be used by or disclosed to any person, firm, or corporation for any purpose whatsoever without the written permission of the Owner. The Owner may have additional requirements or restrictions for which the Contractor is also responsible. The acceptance of these drawings by vendor, bidders, fabricators, or Contractors and their agents constitutes agreement to the following. These design intent drawings are for the sole purpose of design intent only and not intended for construction purposes. Resulting working drawings, shop drawings and contract documents including permit documents are the sole responsibility of the Contractor in every respect.

GDMF - Monument, Flat Face - Elevation

Scale: 3/16" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: 3/16" = 1' - 0"

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

GDMF, Flat Face - Sizes Scale: 3/16" = 1' - 0"

Drawing Title: GDMF - Monument, Hard/Flat Face Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

SFW - Wall Sign, Full Mold Standard 3

This wall sign is made with full mold faces and returns on both the CAT Sign Face and Dealer Name Face. The Cat logo is raised. The two faces are mechanically fastened together. It can be internally illuminated or non-illuminated.

Dimensions (ft-in/mm) Code SFW-400 SFW-300 SFW-200

A 4’-0“/1219 3’-0”/914 2’-0”/610

B D 16’-0”/4876 1’-7/16”/317.5 12’-0”/3658 1’-7/16”/317.5 8’-0”/2438 1’-1/16”/282.5

5 1

R 66’-31/8”/20196 mm 38’-1013/16”/11858 mm 25’-111/8”/7903 mm

Typical Specification

Cat Sign Face, Full Mold

Dealer Name Face, Full Mold - Returns Only

Custom yellow vacuumed formed polycarbonate/acrylic, returns (sides) only. Opaque black vinyl dealer name applied in accordance with approved GBM Dealer lockup.

Sign Cabinet

Illumination (Optional (N))

Structural metal frame with manufactured aluminum shell, painted yellow. Return painted black to correspond with Cat sign face. Use Voltarc TriLight Max T8 long life lamps with Kulka lampholder to ensure even quality lumens across entire sign face. For locations that reach temperatures below zero Celsius (32 Fahrenheit), use the Voltarc TriLight max thermal lamp. All electrical to be in accordance with applicable codes.

Hinged Access

Mounting Cleat

Trim face flanges @ joint. Mechanically fasten together. Black caulk seam to prevent light leaks

Section Detail @ joint between faces

Perspective

Scale: NTS

Full Mold - Typical Section Detail

Continuous hinged access one side, or as required for expedient electrical service and maintainence.

White polycarbonate/acrylic, vacuum formed, painted black. Prior to applying black paint, mask Cat logo to expose white. Apply translucent yellow vinyl on Cat “triangle” accordingly.

Continuous aluminum angle mounting cleat mechanically fastened together to sign cabinet and wall surface, as required.

1 R (radius)

2 3

4 Materials

Plan View Scale: 1/4" = 1' - 0"

7 -

Sign Faces [TBC]

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

Scale: NTS

6 -

SFW-400

Vinyl

SFW-300

• 3M - yellow translucent #3630-125 • or approved equivalent

Paint - Special Color Match

SFW-200

SFW Wall Sign, Full Mold Face - Elevation

Scale: 1/4" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: 1/4" = 1' - 0"

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

SFW, Full Mold - Sizes Scale: 1/4" = 1' - 0"

Drawing Title: SFW - Wall Sign, Full Mold Drawn by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

SFW - Wall Sign, Partial Mold (logo only) Standard This wall sign is made with a partial mold face on the CAT logo only, and has no returns. The CAT Sign Face and Dealer Name Face are two separate pieces that are joined by an “H” channel. It can be internally illuminated or non-illuminated.

Dimensions (ft-in/mm) Code A SFW-600 6’-0“/1828 SFW-500 5’-0“/1524

B 24’-0”/7315 20’-0”/6096

D 2’-63/4”/781 2’-31/2”/698

3 5

R 118’-71/8”/36147 mm 116’-6”/35509 mm(?)

Typical Specifications

Cat Sign Face, Partial Mold (logo only)

Dealer Name Face - No Mold

Custom yellow polycarbonate/acrylic. Opaque black vinyl dealer name applied in accordance with approved GBM Dealer lockup. Structural metal frame with manufactured aluminum shell, painted yellow. Return painted black to correspond with Cat sign face.

Hinged Access

Mounting Cleat

Illumination (Optional (N))

Divider bar extrusion

Sign Cabinet

Section Detail @ joint between faces

Perspective

Scale: NTS

Partial Mold - Typical Section Detail Scale: 3/8" = 1' - 0"

Continuous hinged access one side, or as required for expedient electrical service and maintainence. Continuous aluminum angle mounting cleat mechanically fastened together to sign cabinet and wall surface, as required.

White polycarbonate/acrylic, vacuum formed, painted black. Prior to applying black paint, mask Cat logo to expose white. Apply translucent yellow vinyl on Cat “triangle” accordingly.

R (radius)

Plan View Scale: 3/16" = 1' - 0"

Materials

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

Sign Faces [TBC]

7 -

6 -

Scale: 3/16" = 1' - 0"

SFW-600

Vinyl

SFW-500

• 3M - yellow translucent #3630-125 • or approved equivalent

Paint - Special Color Match

SFW Wall Sign, Partial Mold Face - Elevation

Scale: 3/16" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: 3/16" = 1' - 0"

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

SFW, Partial Mold - Standard Sizes Scale: 3/16" = 1' - 0"

Drawing Title: SFW, Wall Sign, Partial Mold Drawn by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

SFW - Wall Sign, Curved Flex Face Standard This wall sign has a curved flex face that is framed with a manufactured aluminum mechanical tensioning system. Illumination is preferred.

Dimensions (ft-in/mm) Code A SFW-800 8’-0”/2438 SFW-700 7’-0”/2134

B 32’-0”/9754 28’-0”/8534

1 D 2’-0”/609 1’-9”/533

SignComp 7000 Series Econoflex extrusion or approved equal.

R 158’-29/16”/48225 mm 138’-51/4”/42195 mm

Typical Specification

Flex Sign Face

Sign Cabinet

3M Panagraphics 3 with custom yellow and black vinyl applied. Black vinyl is knocked out to reveal white letters behind. Add custom yellow vinyl behind black for triangle. Structural metal frame with manufactured aluminum shell, painted yellow. Return painted black to correspond with Cat Logo and brackground. Provide maintenance access through one face.

Illumination (Optional (N))

Mounting Cleat

Curved Flex Face - Section Detail Scale: NTS

Continuous aluminum angle mounting cleat mechanically fastened together to sign cabinet and wall surface, as required.

R (radius)

1 2

Plan View

Scale: 1/8" = 1' - 0"

Perspective Scale: NTS

1 2 3

Materials

Sign Faces [TBC]

SFW-800

• 3M Panagraphics 3 • or approved equivalent

SFW-700

Vinyl

• 3M - yellow translucent #3630-125 (with opaque backer) / black #7725-12 • or approved equivalent

Paint - Special Color Match

SFW - Wall Sign, Flex Face, Curved

Scale: 1/8" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: 1/8" = 1' - 0"

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

SFW, Flex Face - Sizes Scale: 1/8" = 1' - 0"

Drawing Title: SFW, Wall Sign, Curved Flex Face Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

SFWC - Wall Sign, No Mold Face Standard, New (2012) This wall sign is made of the CAT Sign Face and Dealer Name Face which are two separate pieces. The two faces are joined by an “H” channel. Illumination is preferred.

Dimensions (ft-in/mm) Code SFWC-600 SFWC-500 SFWC-400 SFWC-300 SFWC-200

A 6’-0“/1829 5’-0“/1524 4’-0”/1219 3’-0”/914 2’-0”/610

B 24’-0”/7315 20’-0”/6096 16’-0”/4876 12’-0”/3658 8’-0”/2438

3 D 1’-31/8”/384.1 101/2”/266.7(?) 1’-7/16”/317.5 1’-7/16”/317.5 111/16”/282.5

R 118’-71/8”/36147 mm 116’-6”/35509 mm (?) 66’-31/8”/20196 mm 38’-1013/16”/11858 mm 25’-111/8”/7903 mm

5 1

Typical Specifications

Cat Sign Face, No Mold

White polycarbonate/acrylic, curved but not molded (vacuum formed). Black vinyl knocked out for entire logo. Apply yellow triangle behind the black on pre-mask.

Dealer Name Face, No Mold

Sign Cabinet

Illumination (Optional (N))

Hinged Access

Mounting Cleat

Custom yellow polycarbonate/acrylic with applied opaque black vinyl dealer Name applied in accordance with approved GBM Dealer lockup.

Divider bar extrusion

Section Detail @ joint between faces

Perspective

Scale: NTS

No Mold Face - Typical Section Detail Scale: 3/8" = 1' - 0"

Continuous hinged access one side, or as required for expedient electrical service and maintainence.

1 R (radius)

Continuous aluminum angle mounting cleat mechanically fastened together to sign cabinet and wall surface, as required.

Plan View Scale: 3/16" = 1' - 0"

Materials

Sign Faces [TBC]

• SABIC - polycarbonate (Lexan) pigmented solar grade #SG 410 • Evonik - modified acrylic [TBD] • EGR Group - Caterpillar “orange” custom UHI acrylic • or approved equivalent

7 -

Scale: 3/16" = 1' - 0"

SFWC-600

6 -

SFWC-500

Vinyl

SFWC-400

• 3M - yellow translucent #3630-125 / black #7725-12 • or approved equivalent

Paint - Special Color Match

SFWC-300

SFWC-200

SFWC - Wall Sign, No Mold Face - Elevation

Scale: 3/16" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: 3/16" = 1' - 0"

SFWC - Sizes Scale: 3/16" = 1' - 0"

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

Drawing Title: SFWC - Wall Sign, No Mold Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Checked Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

SFWX- Wall Sign, Flat Flex Face Basic, New (2012) This wall sign has a flex face that is framed with a manufactured aluminum mechanical tensioning system. It is non-illuminated.

Dimensions (ft-in/mm)

Code A B D SFWX-600 6’-0“/1829 24’-0”/7315 9”/230 SFWX-500 5’-0“/1524 20’-0”/6096 71/2”/190

Typical Specifications

Flex Sign Face

Sign Cabinet

Mounting Cleat

3 2 SignComp 7000 Series Econoflex extrusion or approved equal.

Flat Flex Face - Section Detail Scale: 3/8" = 1' - 0"

Perspective Scale: 3/16" = 1' - 0"

Plan View Scale: 3/16" = 1' - 0"

Materials

Sign Faces [TBC]

6 -

• 3M Panagraphics 3 • or approved equivalent

SFWX-600

Vinyl

• 3M - yellow translucent #3630-125 (with opaque backer) / black #7725-12 • or approved equivalent

Paint - Special Color Match

SFWX-500

BrandActive (USA) Inc. SFWX - Wall Sign, Flat Flex Face - Elevation 10120 South Eastern Avenue

Scale: 3/16" = 1' - 0"

Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Drawing Title: SFWX - Wall Sign, Flat Flex Face Side Elevation SFWX, Flat Flex Face - Sizes Primary Dealer Network Sign Family Check by: MR Modified by: PY 2 Scale: 3 3/16" = 1' 0" Scale: 3/16" = 1' 0" Date: 10 July 2012 Date: 10 July 2012 Technical Specifications

N/A

Project:

Rev No.

Date:

By:

Scale: as noted

Client:

File: CATDlrNtwrkSgnTechDoc

Approved by: MF

Date: pending

Sheet:

SFWF - Wall Sign, Flat Face/Hard Basic, New (2012) The wall sign is a flat metal cabinet with graphics applied to each side. It is nonilluminated.

Dimensions (ft-in/mm) Code SFWF-400 SFWF-300 SFWF-200

A 4’-0”/1219 3’-0”/914 2’-0”/610

B 16’-0”/4876 12’-0”/3658 8’-0”/2438

2 1

D 3”/228 2”/190 11/2”/38

Typical Specification

Cat Sign Face

Dealer Name Face

Sign Cabinet

Flat Face - Section Detail Scale: NTS

Perspective Scale: NTS

Plan View Scale: 1/4" = 1' - 0"

1 2

6 -

SFWF-400

Materials Vinyl

SFWF-300

• 3M - yellow translucent #3630-125 (with opaque backer added) / opaque white #7725-10 • or approved equivalent

Paint - Special Color Matc

SFWF-200

SFWF - Wall Sign, Flat Face/Hard - Elevation

Scale: 1/4" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side Elevation Scale: 1/4" = 1' - 0"

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

SFWF, Flat Face/Hard - Sizes Scale: 1/4" = 1' - 0"

Drawing Title: SFWF - Wall Sign, Flat Face Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

DIR - Directional Signs Basic Directional signs have flat panels mounted either/both sides of the posts. The back panel is blank unless additional directional information is required.

.75X

Dimensions (ft-in/mm) Code DIR-100 DIR-200 DIR-300

A 7’-0”/2134 6’-0”/1829 5’-0”/1524

B 4’-0”/1219 3’-0”/914 2’-0”/6010

X 3“/76 2“/51 11/2”/38

X .5X

Panel

Post

Graphics

.75X

eq.

1.5X

1.5X Arrow centers on

1.5X

eq.

1.5X

first message of one only

.75X

1.5X

X X

Typical Specification

Arrow centers on first message of one only

1.5X

Aluminum sheet painted Caterpillar corporate yellow on face and returns. Square aluminum tube painted black. Applied black vinyl. All decorations applied in black vinyl. X = 1.5X =

X X 1.25X .625X

= = = =

black rule line arrow, letter height & between two directions

X = 1.5X = .75X =

black rule line letter height between two lines of same message

black rule line arrow & letter height between two directions between two messages same direction

Multiple Directional Message Layout

Scale: NTS

Double Directional Message Layout

Scale: NTS

Single Information Message Layout - 2 Lines Scale: NTS

A X

Sales Customer Parking A

Sign Faces

Sales Customer Parking

Shipping Receiving

Service The Cat Rental Store

Materials

Shipping Receiving Service The Cat Rental Store

Sales Service

Vinyl

• 3M - black #7725-12 • or approved equivalent

Hieght of face increases by X only, to accommodate additional messages.

Paint - Special Color Match

Match yellow and black paints to the materials being used for the sign. Examples of acceptable paint includes Akzo SIGN 10467 semi-gloss custom yellow and 80314 satin black.

Customer Parking

• Aluminum

Contact: Corporate and Dealer Identity Help Desk Toll-free: 1.800.566.7782 U.S. tel.: +1.309.675.5135 Tieline: 7.725.5135 Email: brand@cat.com Website: https://brand.cat.com

DIR-100

DIR-200

DIR-300

DIR - Directional/Infomational Signs, Post & Panel

Scale: 1/2" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

Silver Base - End View Scale: 1/2" = 1' - 0"

Drawing Title: DIR - Directional Signs Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

DIRM - Directional Monoliths Standard Directional monoliths are fabricated as metal clad signs.

C B

Dimensions (ft-in/mm)

E D

Code A B C D E F DIRM-100 8’-0”/2438 3’-0”/914 3’-7“/1092 1’-61/2”/685 8“/381 51/4“/381 DIRM-200 6’-0”/1829 2 ’-0”/610 2’-5“/737 1’-3”/571 10“/317 41/8“/317

Typical Specification

Sign Cabinet

Graphics

Base Cover

Fabricated structural aluminum frame clad with aluminum skin, painted Caterpillar corporate yellow.

Lettering and arrows are applied in black vinyl.

Plan View Scale: 1/2" = 1' - 0"

Fabricated aluminum base cover, two piece construction. Mechanically fastened together and to base. Painted black. 3 29

4 29

5 29

1 B

DIRM-100

Sales Customer Parking

Shipping

Receiving

Receiving DIRM-200

Service The Cat Rental Store

Sales Customer Parking

Service The Cat Rental Store

Shipping/Receiving Power Systems Service The Cat Rental Store

Materials

Sign Faces • Aluminum

Vinyl

• 3M - black #7725-12 • or approved equivalent

Paint - Special Color Match

DIRM Directional Monolith

Scale: 1/2" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Side View

Scale: 1/2" = 1' - 0"

DIRM - Sizes Scale: 1/2" = 1' - 0"

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

Perspective Scale: NTS

Drawing Title: DIRM - Directional Monoliths Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

WAL/WALH - Information Signs Basic Width of sign increases by “A” only, as necessary.

Wall signs are break formed aluminum panels that are mechanically fastened to wall surfaces.

Dimensions (ft-in/mm) Code WAL-100 WAL-200 WAL-300 WALH-100 WALH-200 WALH-300

A B C 4’-0”/1219 3-0”/914 2’-0”/610 4’-0”/1219 12’-0”/3658 2”/50.8 3-0”/914 9’-0”/2743 11/2”/38.1 2’-0”/610 6’-0”/1829 1”/25.4

X 3“/76 2“/51 11/2”/25 3“/76 2“/51 11/2”/38

B (minimum)

eq.

X 2X

2.5X A 4X

Typical Specification

1 2

Panel

Aluminum sheet break formed to create return, painted custom yellow face and returns.

Message centered on length of sign.

WALH - Typical Message Layout

Graphics

Applied black vinyl. Black rule to be applied to full depth of top return.

Scale: 1/2" = 1' - 0" 5 -

3 -

B (minimum)

Single Information Message Layout Scale: NTS

Width of sign increases by “A” only, as necessary. A

X 3X

Receiving

A 4X

WALH - Horizontal Wall Sign Scale: 1/2" = 1' - 0" 6 -

3 -

6 -

5 29

2 A

Materials

Sign Faces • Aluminum

Vinyl

Sales

• 3M - black #7725-12 • or approved equivalent

Service A

Paint - Special Color Match

WAL-100

WAL-200

WAL - Wall Signs, Informational

Mechanically fastened to wall surface Counter sunk screw, painted to match respective return

WAL-300

Scale: 1/2" = 1' - 0" BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Alum. angle mounting bracket top & bottom of each sign

Customer Parking

Side View Scale: NTS

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

Typical Section Detail Scale: NTS

Drawing Title: WAL/WALH - Information Signs Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

Appendix - Master Sign Family Matrix Technique

Sheet #

Code

Alt. Code

Grade*

Existing/ New

Description

Shape

Illumination

Overall Height (ft/in) A * Only two grades exist: Standard (curved faces and internally lit) and Basic (flat faces and typically unlit (flood lit ground signs optional)) Pylons 5 DSP-02 D (03) Standard Existing Single Pole Pylon Curved Yes 15’-0”

Face Width (ft/in) B

Face Height (ft/in) C

Overall Height (mm) A

Face Width (mm) B

Face Height (mm) C

12’-0”

3’-0”

4572mm

3658mm

914mm

DSP-03

D (02)

Standard

Existing

Single Pole Pylon

Curved

Yes

20’-0”

16’-0”

4’-0”

6096mm

4876mm

1219mm

DSP-04

D (01)

Standard

Existing

Single Pole Pylon

Curved

Yes

25’-0”

20’-0”

5’-0”

7620mm

6096mm

1524mm

DSP-05

Standard

Existing

Single Pole Pylon

Curved

Yes

30’-0”

24’-0”

6’-0”

9144mm

7315mm

1829mm

DSPC-02

Standard

New

Single Pole Pylon

Curved

Yes

15’-0”

12’-0”

3’-0”

4572mm

3658mm

914mm

DSPC-03

Standard

New

Single Pole Pylon

Curved

Yes

20’-0”

16’-0”

4’-0”

6096mm

4876mm

1219mm

DSPC-04

Standard

New

Single Pole Pylon

Curved

Yes

25’-0”

20’-0”

5’-0”

7620mm

6096mm

1524mm

DSPC-05

Standard

New

Single Pole Pylon

Curved

Yes

30’-0”

24’-0”

6’-0”

9144mm

7315mm

1829mm

DSP-06

Standard

Existing

Single Pole Pylon

Curved

Yes

35’-0”

28’-0”

7’-0”

10668mm 8534mm

2134mm

DSP-07

Standard

Existing

Single Pole Pylon

Curved

Yes

40’-0”

32’-0”

8’-0”

12192mm 9754mm

2438mm

DSP-08

Standard

Existing

Single Pole Pylon

Curved

Yes

50’-0”

36’-0”

9’-0”

15240mm 10973mm 2743mm

DDP-02

C (03)

Standard

Existing

Double Pole Pylon

Curved

Yes

15’-0”

12’-0”

3’-0”

4572mm

3658mm

914mm

DDP-03

C (02)

Standard

Existing

Double Pole Pylon

Curved

Yes

20’-0”

16’-0”

4’-0”

6096mm

4876mm

1219mm

DDP-04

C (01)

Standard

Existing

Double Pole Pylon

Curved

Yes

25’-0”

20’-0”

5’-0”

7620mm

6096mm

1524mm

DDP-05

Standard

Existing

Double Pole Pylon

Curved

Yes

30’-0”

24’-0”

6’-0”

9144mm

7315mm

1829mm

DDPC-02

Standard

New

Double Pole Pylon

Curved

Yes

15’-0”

12’-0”

3’-0”

4572mm

3658mm

914mm

DDPC-03

Standard

New

Double Pole Pylon

Curved

Yes

20’-0”

16’-0”

4’-0”

6096mm

4876mm

1219mm

DDPC-04

Standard

New

Double Pole Pylon

Curved

Yes

25’-0”

20’-0”

5’-0”

7620mm

6096mm

1524mm

DDPC-05

Standard

New

Double Pole Pylon

Curved

Yes

30’-0”

24’-0”

6’-0”

9144mm

7315mm

1829mm

DDP-06

Standard

Existing

Double Pole Pylon

Curved

Yes

35’-0”

28’-0”

7’-0”

10668mm 8534mm

2134mm

DDP-07

Standard

Existing

Double Pole Pylon

Curved

Yes

40’-0”

32’-0”

8’-0”

12192mm 9754mm

2438mm

DDP-08

Standard

Existing

Double Pole Pylon

Curved

Yes

50’-0”

36’-0”

9’-0”

15240mm 10973mm 2743mm

Monoliths 14 MON-200

A (03)

Standard

Existing

Monolith

Curved

Yes

12’-0”

3’-0”

3658mm

914mm

MON-300

A (02)

Standard

Existing

Monolith

Curved

Yes

16’-0”

4’-0”

4877mm

1219mm

MON-400

A (01)

Standard

Existing

Monolith

Curved

Yes

20’-0”

5’-0”

6096mm

1524mm

MON-500

Standard

Existing

Monolith

Curved

Yes

24’-0”

6’-0”

7315mm

1829mm

MONC-200

Standard

New

Monolith

Curved

Yes

12’-0”

3’-0”

3658mm

914mm

MONC-300

Standard

New

Monolith

Curved

Yes

16’-0”

4’-0”

4877mm

1219mm

MONC-400

Standard

New

Monolith

Curved

Yes

20’-0”

5’-0”

6096mm

1524mm

MONC-500

Standard

New

Monolith

Curved

Yes

24’-0”

6’-0”

7315mm

1829mm

MONF-200

Basic

New

Monolith

Flat

No/(Yes flood) 12’-0”

3’-0”

3658mm

914mm

MONF-300

Basic

New

Monolith

Flat

No/(Yes flood) 16’-0”

4’-0”

4876mm

1219mm

MONF-400

Basic

New

Monolith

Flat

No/(Yes flood) 20’-0”

5’-0”

6096mm

1524mm

MONF-500

Basic

New

Monolith

Flat

No/(Yes flood) 24’-0”

6’-0”

7315mm

1829mm

Monument

Curved

Yes

5’-0”

12’-0”

3’-0”

1524mm

3658mm

914mm

Monument

Curved

Yes

6’-0”

16’-0”

4’-0”

1829mm

4876mm

1219mm

Monument

Curved

Yes

7’-0”

20’-0”

5’-0”

2134mm

6096mm

1524mm

Curved

Yes

5’-0” 12’-0” BrandActive (USA) Inc.

3’-0”

1524mm

3658mm

914mm

Curved

Yes

Suite 200 6’-0” 16’-0” Henderson NV 89052

4’-0”

1829mm

4877mm

1219mm

7’-0”

20’-0”

5’-0

2134mm

6096mm

No/(Yes flood) 5’-0”

12’-0”

3’-0”

1524mm

3656mm

Legend (sign codes) Monuments H = Hard/Flat Face (aluminum) face 19 GDM-02 C (03) Standard Existing N = No Mold Face without molded/cutout logo or returns 19 GDM-03 C (02) Standard Existing X = Flex Face (N) = illumination = non-illuminated) 20 GDM-04optional (If N used C (01)in order Standard Existing

of the Owner, and were created, evolved and developed for the use on and in connection with the specific project. None of such ideas, designs, arrangements or plans shall be used by or disclosed to any person, firm, or corporation for any purpose whatsoever without the written permission of the Owner. The Owner may have additional requirements or restrictions for which the Contractor is also responsible.

GDMC-03

Standard

New

Monument

The acceptance of these drawings by vendor, bidders, fabricators, or Contractors and their agents constitutes agreement to the following. These design intent drawings are for the sole purpose of design intent only and not intended for construction purposes. Resulting working drawings, shop drawings and contract documents including permit documents are the sole responsibility of the Contractor in every respect.

GDMC-04

Standard

New

Monument

Curved

GDMF-02

Basic

New

Monument

Flat

Yes

10120 South Eastern Avenue T 866 478 7322 F 949 757 0419 www.brandactive.com

Client:

No Mold

Partially Molded

Fully Molded

Hard Flat Face Flex Face

(with returns)

Curved

(frameless edge)

(Cat logo raised only)

       

          

   

          

   

          

 Dealer Network Sign Family Primary  Specifications Technical 1524mm  Project: 914mm 

Drawing Title: Appendix - Master Sign Family Matrix Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

MONC-400

Standard

New

Monolith

Curved

Yes

20’-0”

5’-0”

6096mm

1524mm

MONC-500

Standard

New

Monolith

Curved

Yes

24’-0”

6’-0”

7315mm

1829mm

New

Monolith

Flat

No/(Yes flood) 12’-0”

3’-0”

3658mm

914mm

Appendix - Master Sign Family Matrix 17 MONF-200 Basic 17 Sheet # 17

MONF-300 Code MONF-400

Monolith Description Monolith

Flat Shape Flat

Basic

New Existing/ New New New

MONF-500

Monolith

Flat

Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Standard Basic Grade* Standard Basic Standard Basic Standard

Existing Existing Existing Existing Existing Existing New Existing New Existing New Existing New Existing/ Existing New New New New New

Monument Wall Mounted Sign Monument Wall Mounted Sign Monument Wall Mounted Sign Monument Wall Mounted Sign Monument Wall Mounted Sign Monument Wall Mounted Sign Monument Description Wall Mounted Sign Monument Wall Mounted Sign Monument Wall Mounted Sign

Curved Curved Curved Curved Curved Curved Curved Curved Curved Curved Curved Curved Flat Shape Curved Flat Curved Flat Curved

Yes Yes/(No) Yes Yes/(No) Yes Yes/(No) Yes Yes/(No) Yes Yes/(No) Yes Yes/(No) No/(Yes flood) Illumination Yes/(No) No/(Yes flood) Yes/(No) No/(Yes flood) Yes/(No)

5’-0” 2’-0 6’-0” 3’-0 7’-0” 4’-0 5’-0” 5’-0 6’-0” 6’-0 7’-0” 7’-0 5’-0” Overall 8’-0 6’-0” Height 2’-0 (ft/in) 7’-0” A3’-0

12’-0” 8’-0” 16’-0” 12’-0” 20’-0” 16’-0” 12’-0” 20’-0” 16’-0” 24’-0” 20’-0” 28’-0” 12’-0” Face 32’-0” 16’-0” Width 8’-0” (ft/in) 20’-0” B12’-0”

Standard Standard Standard Standard Standard Standard Basic Standard Basic Standard Basic Standard Basic Standard Basic Standard

New Existing New Existing New Existing New Existing New Existing New Existing New Existing New New

Wall Mounted Sign Wall Mounted Sign Wall Mounted Sign Wall Mounted Sign Wall Mounted Sign Wall Mounted Sign Wall Mounted Sign Wall Mounted Sign Wall Mounted Sign Wall Mounted Sign Wall Mounted Sign Wall Mounted Sign Wall Mounted Sign Wall Mounted Sign Wall Mounted Sign Wall Mounted Sign

Curved Curved Curved Curved Curved Curved Flat Curved Flat Curved Flat Curved Flat Curved Flat Curved

Yes/(No) Yes/(No) Yes/(No) Yes/(No) Yes/(No) Yes/(No) No Yes/(No) No Yes/(No) No Yes/(No) No Yes/(No) No Yes/(No)

4’-0 2’-0 5’-0 3’-0 6’-0 4’-0 5’-0 5’-0 6’-0 6’-0 2’-0 7’-0 3’-0 8’-0 4’-0 2’-0

16’-0” 8’-0” 20’-0” 12’-0” 24’-0” 16’-0” 20’-0” 20’-0” 24’-0” 24’-0” 8’-0” 28’-0” 12’-0” 32’-0” 16’-0” 8’-0”

Standard Basic Standard Basic

New Existing New Existing

Wall Mounted Directional SignSign Wall Mounted Directional SignSign

Curved Flat Curved Flat

Yes/(No) No Yes/(No) No

3’-0 5’-0” 4’-0 6’-0”

12’-0” 2’-0” 16’-0” 3’-0”

Standard Basic Standard Standard

New Existing New Existing

Wall Mounted Directional SignSign Wall Mounted Sign Directional Monolith

Curved Flat Curved Flat

Yes/(No) No Yes/(No) No/Yes (flood)

5’-0 7’-0” 6’-0 6’-0”

20’-0” 4’-0” 24’-0” 2’-0”

4’-0”

27 SFWX-500 30 DIRM-100 27 SFWX-600 Information Wall Signs

Basic Standard Basic

New Existing New

Wall Mounted Sign Directional Monolith Wall Mounted Sign

Flat Flat Flat

No(flood) 5’-0 No/Yes 8’-0” No 6’-0

20’-0” 3’-0” 24’-0”

3’-7”

28 31

SFWF-200 WAL-300

Basic Basic

New Existing

Wall Mounted Sign Information Sign

Flat Flat

No No

2’-0 2’-0”

8’-0” 2’-0”

610mm 610mm

2438mm 610mm

28 31

SFWF-300 WAL-200

Basic Basic

New Existing

Wall Mounted Sign Information Sign

Flat Flat

No No

3’-0 3’-0”

12’-0” 3’-0”

914mm 914mm

3658mm 914mm

28 31

SFWF-400 WAL-100

Basic Basic

New Existing

Wall Mounted Sign Information Sign

Flat Flat

No No

4’-0 4’-0”

16’-0” 4’-0”

1219mm 1219mm 4876mm 1219mm

Directional Signs and Monoliths 31 WALH-300 29 DIR-300 31 WALH-200 29 DIR-200 31 WALH-100

Basic Basic Basic Basic Basic

Existing Existing Existing Existing Existing

Information Sign Directional InformationSign Sign Directional Sign Information Sign

Flat Flat Flat Flat Flat

No No No No No

2’-0” 5’-0” 3’-0” 6’-0” 4’-0”

6'-0" 2’-0” 9'-0" 3’-0” 12'-0"

3’-0”

Basic

Existing

Directional Sign

Flat

7’-0”

4’-0”

610mm 1829mm 1524mm 610mm 914mm 2743mm 610mm 1829mm 1219mm 914mm 3658mm 914mm 2314mm 1219mm 1219mm

DIRM-200 Standard Existing Directional Monolith Flat No/Yes (flood) 6’-0” Legend (sign codes) F = flat and hard (aluminum) face Legend (sign codes) 30 DIRM-100 Standard Existing Directional Monolith Flat No/Yes (flood) 8’-0” H = Hard/Flat (aluminum) face molded/cutout logo or returns C =Face curved face without N = No Mold(N) Face without molded/cutout or returns Information Wall Signs = illumination optional (Iflogo N used in order = non-illuminated) X = Flex Face 31 WAL-300 Basicother flex are Existing Information Sign to forceFlat 2’-0” X = flex in new flat flex wall sign only; existing and we don't want updating all dwgs No

2’-0”

2’-5”

1829mm

914mm

1092mm

3’-0”

3’-7”

2438mm

610mm

737mm

2’-0”

610mm

3’-0”

914mm

4’-0”

1219mm

Primary 1219mm Dealer Network Sign Family Technical Specifications 1829mm

Monuments Wall Signs 19 GDM-02 C (03) 23 SFW-200(N) B (04) 19 GDM-03 C (02) 23 SFW-300(N) B (03) 20 GDM-04 C (01) 23 SFW-400(N) B (02) 21 GDMC-02 24 SFW-500(N) B (01) 21 GDMC-03 24 SFW-600(N) 21 GDMC-04 25 SFW-700(N) 22 GDMF-02 Sheet Alt. Code 25 # Code SFW-800(N) 22 GDMF-03 26 SFWC-200(N) 22 GDMF-04 26 SFWC-300(N) Wall Signs 26 SFWC-400(N) 23 SFW-200(N) B (04) 26 SFWC-500(N) 23 SFW-300(N) B (03) 26 SFWC-600(N) 23 SFW-400(N) B (02) 27 SFWX-500 24 SFW-500(N) B (01) 27 SFWX-600 24 SFW-600(N) 28 SFWF-200 25 SFW-700(N) 28 SFWF-300 25 SFW-800(N) 28 SFWF-400 26 SFWC-200(N) Directional Signs and Monoliths 26 SFWC-300(N) 29 DIR-300 26 SFWC-400(N) 29 DIR-200

26 29 26 30

SFWC-500(N) DIR-100 SFWC-600(N) DIRM-200

DIR-100

(N) = illumination optional (If N used in order = non-illuminated)

WAL-200

Basic

Existing

Information Sign

WAL-100

Basic

Existing

Information Sign

Flat Flat

WALH-300

Basic

Existing

Information Sign

Flat

WALH-200

Basic

Existing

Information Sign

Flat

3’-0”

BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

4’-0”

2’-0”

6'-0"

3’-0”

9'-0"

Client:

3’-0” 4’-0” 5’-0” 3’-0” 4’-0” 5’-0 3’-0” Face 4’-0” Height (ft/in) 5’-0” C

2’-0” 3’-0” 2’-5”

2’-0”

1219mm Face 1524mm Width 1829mm (mm) B

1524mm 610mm 1829mm 914mm 2134mm 1219mm 1524mm 1524mm 1829mm 1829mm 2134mm 2134mm 1524mm Overall 2438mm 1829mm Height 610mm (mm) 2134mm A914mm

3658mm 2438mm 4876mm 3658mm 6096mm 4876mm 3658mm 6096mm 4877mm 7315mm 6096mm 8534mm 3656mm Face 9754mm 4876mm Width 2438mm (mm) 6096mm B3658mm

1219mm 610mm 1524mm 914mm 1829mm 1219mm 1524mm 1524mm 1829mm 1829mm 610mm 2134mm 914mm 2438mm 1219mm 610mm

4876mm 2438mm 6096mm 3658mm 7315mm 4876mm 6096mm 6096mm 7315mm 7315mm 2438mm 8534mm 3658mm 9754mm 4876mm 2438mm

914mm 1524mm 3658mm 610mm 1219mm 4876mm 1829mm 914mm 1524mm 2314mm 6096mm 1219mm 1829mm 1829mm 7315mm 914mm 1524mm 6096mm 2438mm 610mm 1829mm 7315mm

610mm 914mm

Project:

2743mm

  Hard Flat Face  

Technique

4’-0” Face 5’-0” Width 6’-0” (ft/in) B

Face Height (ft/in) C

4876mm Overall 6096mm Height 7315mm (mm) A

  

No/(Yes flood) 16’-0” Illumination Overall No/(Yes flood) 20’-0” Height No/(Yes flood) 24’-0” (ft/in) A

Alt. Code

Basic Grade* Basic

   Face Height (mm) C

No Mold

Partially Molded

1219mm



1524mm 1219mm 1524mm 914mm Face 1219mm Height (mm) 1524mm C

   No Mold

    

914mm 1219mm 1092mm

Flex Face

Curved

(frameless edge)

    

  Technique Partially Molded

Fully Molded (with returns)

(Cat logo raised only)

 edge) (frameless

  

Hard Flat Face Flex Face

    

737mm

Curved

   

    

610mm

(with returns)

(Cat logo raised only)

914mm

Fully Molded

    

     

    

 

                  

Drawing Title: Appendix - Master Sign Family Matrix Modified by: PY Date: 10 July 2012

Scale: as noted File: CATDlrNtwrkSgnTechDoc

Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet:

SFWF-300

Basic

New

Wall Mounted Sign

Flat

3’-0

12’-0”

914mm

3658mm

SFWF-400

Basic

New

Wall Mounted Sign

Flat

4’-0

16’-0”

1219mm

4876mm

29 Sheet # 29

DIR-300 Code DIR-200

Basic Grade* Basic

Directional Sign Description Directional Sign

Flat Shape Flat

DIR-100

Basic

Existing Existing/ Existing New Existing

Directional Sign

Flat

Standard

Existing

Directional Monolith

Standard Standard

Existing Existing

Standard Basic Standard Basic Standard Basic Standard Basic Standard Basic Standard Basic Standard

Existing Existing Existing Existing Existing Existing Existing Existing Existing Existing Existing Existing New

Appendix - Master Sign Family Matrix Directional Signs and Monoliths Alt. Code

30 DIRM-200 Wall Signs 30 DIRM-100 23 SFW-200(N) Information Wall Signs 23 SFW-300(N) 31 WAL-300 23 SFW-400(N) 31 WAL-200 24 SFW-500(N) 31 WAL-100 24 SFW-600(N) 31 WALH-300 25 SFW-700(N) 31 WALH-200 25 SFW-800(N) 31 WALH-100 26 SFWC-200(N)

B (04)

Flat

5’-0” Overall 6’-0” Height No 7’-0” (ft/in) A No/Yes (flood) 6’-0”

2’-0” Face 3’-0” Width 4’-0” (ft/in) B 2’-0”

2’-0” Face 3’-0” Height 4’-0” (ft/in) C 2’-5”

1524mm Overall 1829mm Height 2314mm (mm) A 1829mm

610mm Face 914mm Width 1219mm (mm) B 914mm

610mm Face 914mm Height 1219mm (mm) C 1092mm

Directional Monolith Wall Mounted Sign

Flat Curved

No/Yes (flood) 8’-0” Yes/(No) 2’-0

3’-0” 8’-0”

3’-7”

2438mm 610mm

610mm 2438mm

737mm

Wall Mounted Sign Information Sign Wall Mounted Sign Information Sign Wall Mounted Sign Information Sign Wall Mounted Sign Information Sign Wall Mounted Sign Information Sign Wall Mounted Sign Information Sign Wall Mounted Sign

Curved Flat Curved Flat Curved Flat Curved Flat Curved Flat Curved Flat Curved

3’-0 2’-0” 4’-0 3’-0” 5’-0 4’-0” 6’-0 2’-0” 7’-0 3’-0” 8’-0 4’-0” 2’-0

12’-0” 2’-0” 16’-0” 3’-0” 20’-0” 4’-0” 24’-0” 6'-0" 28’-0” 9'-0" 32’-0” 12'-0" 8’-0”

914mm 610mm 1219mm 914mm 1524mm 1219mm 1829mm 610mm 2134mm 914mm 2438mm 1219mm 610mm

3658mm 610mm 4876mm 914mm 6096mm 1219mm 7315mm 1829mm 8534mm 2743mm 9754mm 3658mm 2438mm

3’-0

12’-0”

914mm

3658mm

4’-0

16’-0”

1219mm

4876mm

5’-0

20’-0”

1524mm

6096mm

SFWC-300(N) Standard New Wall Mounted Sign Curved Yes/(No) Legend (sign codes) FSFWC-400(N) = flat and hard (aluminum) face Standard New Wall Mounted Sign Curved Yes/(No) C = curved face without molded/cutout logo or returns SFWC-500(N) Standard New Wall Mounted Sign Curved Yes/(No) (N) = illumination optional (If N used in order = non-illuminated) Standard New XSFWC-600(N) = flex in new flat flex wall sign only; other flex are existing andWall we Mounted don't wantSign to force Curved updating all dwgsYes/(No)

6’-0

24’-0”

1829mm

7315mm

SFWX-500

Basic

New

Wall Mounted Sign

Flat

5’-0

20’-0”

1524mm

6096mm

SFWX-600

Basic

New

Wall Mounted Sign

Flat

6’-0

24’-0”

1829mm

7315mm

SFWF-200

Basic

New

Wall Mounted Sign

Flat

2’-0

8’-0”

610mm

2438mm

SFWF-300

Basic

New

Wall Mounted Sign

Flat

3’-0

12’-0”

914mm

3658mm

SFWF-400

Basic

New

Wall Mounted Sign

Flat

4’-0

16’-0”

1219mm

4876mm

Directional Signs and Monoliths 29 DIR-300

Basic

Existing

Directional Sign

Flat

5’-0”

2’-0”

1524mm

610mm

DIR-200

Basic

Existing

Directional Sign

Flat

6’-0”

3’-0”

1829mm

914mm

DIR-100

Basic

Existing

Directional Sign

Flat

7’-0”

4’-0”

2314mm

1219mm

DIRM-200

Standard

Existing

Directional Monolith

Flat

No/Yes (flood) 6’-0”

2’-0”

2’-5”

1829mm

914mm

1092mm

DIRM-100

Standard

Existing

Directional Monolith

Flat

No/Yes (flood) 8’-0”

3’-0”

3’-7”

2438mm

610mm

737mm

Information Wall Signs 31 WAL-300

Basic

Existing

Information Sign

Flat

2’-0”

610mm

WAL-200

Basic

Existing

Information Sign

Flat

3’-0”

914mm

WAL-100

Basic

Existing

Information Sign

Flat

4’-0”

1219mm

WALH-300

Basic

Existing

Information Sign

Flat

2’-0”

6'-0"

610mm

1829mm

WALH-200

Basic

Existing

Information Sign

Flat

3’-0”

9'-0"

914mm

2743mm

WALH-100

Basic

Existing

Information Sign

Flat

4’-0”

12'-0"

1219mm

3658mm

26 26 26

B (03)

No Illumination No

  

B (02) B (01)

Yes/(No) No Yes/(No) No Yes/(No) No Yes/(No) No Yes/(No) No Yes/(No) No Yes/(No)

Technique No Mold

Partially Molded

Fully Molded (with returns)

(Cat logo raised only)

    

Hard Flat Face Flex Face

Curved

(frameless edge)

     

       

             

Legend (sign codes) F flat and hard (aluminum) face Legend (sign =codes) C =Face curved face without H = Hard/Flat (aluminum) face molded/cutout logo or returns N = No Mold(N) Face without molded/cutout or returns = illumination optional (Iflogo N used in order = non-illuminated) X = Flex Face X = flex in new flat flex wall sign only; other flex are existing and we don't want to force updating all dwgs (N) = illumination optional (If N used in order = non-illuminated)

BrandActive (USA) Inc. 10120 South Eastern Avenue Suite 200 Henderson NV 89052 T 866 478 7322 F 949 757 0419 www.brandactive.com

Primary Dealer Network Sign Family Technical Specifications Client:

Project:

Drawing Title: Appendix - Master Sign Family Matrix Modified by: PY Date: 10 July 2012 Scale: as noted File: CATDlrNtwrkSgnTechDoc

Check by: MR

N/A

Rev No.

Date:

By:

Date: 10 July 2012 Approved by: MF Date: pending

Sheet: