HPAC Auguist 2021

EVAPORATOR FUNDAMENTALS

UGLY CROSS CONNECTIONS

HRVS/ERVS EXPLAINED

AUGUST 2021

FRESH AIR SOLUTIONS FOR QUALITY INDOOR AIR

ENCOURAGING YOUTH AND WOMEN INTO THE TRADES ACCEPTING SUPPLY CHAIN CHALLENGES

MODERN HYDRONICS 2021 FALL

WAREHOUSE IN-FLOOR INSTALLATION SIZING PANEL RADS FOR LOW WATER TEMPS

SWEET HEAT 2021 This year’s contest-winning projects

ALSO INSIDE Follow Us On

Follow Us On

@hpacmag @hpacmag

PLANNING MULTI-ZONE LAYOUTS BOILER CHEMISTRY CONSIDERATIONS

a publication of

Reimagine Your Mechanical Room Element Q The Future of Water Management

• Complete domestic hot water wellness solution • Fits through a standard doorway (75% less footprint) • Up to 65% reduction in installation time • Automates “clipboard” health monitoring

Safe Sustainably mitigates waterborne pathogens

Smart Real-time data reporting across devices

Simple Simplifies design, installation and operation

817.335.9531 | lyncbywatts.com ©2021 Lync

CONTENTS

AUGUST 2021 / VOL. 95 NO. 5

58

10 FEATURES 10 HVAC

DEPARTMENTS 52 PLUMBING

VENTILATION: WHO NEEDS IT? As new standards lead to tighter building envelopes, homes require mechanical ventilation solutions.

By Ian McTeer

LOOK FOR THE OPPORTUNITIES In a year of complications and unforeseen twists, where there’s a will there’s a way.

By Steve Goldie

14 HVAC

58 REFRIGERATION

HRVS AND ERVS EXPLAINED This recent HPAC Magazine webinar discusses the role of mechanical ventilation systems in buildings.

By Logan Caswell

UNDERSTANDING EVAPORATORS A fundamental element of the refrigeration cycle, we revisit the basic functions of evaporators and how to keep them operating at their peak.

By Dave Demma

ALSO INSIDE

MH4 AWARDS

MODERN HYDRONICS 2021 FALL

WAREHOUSE IN-FLOOR INSTALLATION SIZING PANEL RADS FOR LOW WATER TEMPS

SWEET HEAT 2021 This year’s contest-winning projects

PLANNING MULTI-ZONE LAYOUTS BOILER CHEMISTRY CONSIDERATIONS

a publication of

HPACMAG.COM

SWEET HEAT AWARDS 2021 Celebrating the top entries in the inaugural Sweet Heat competition.

MH10

PIPING ZONING CONSIDERATIONS Planning your piping layouts.

MH14 BOILERS OPTIMIZING BOILER CHEMISTRY Maintaining clean water is essential.

MH20

DESIGN

WATER WORKS Net zero carbon TRCA building.

6 UPFRONT 7 NEWS FEATURE An interview with Rachel Hesketh: working to raise the profile of women and youth in the trades.

8 INDUSTRY NEWS 49 MECHANICAL SUPPLY NEWS 51 PEOPLE 56 PLUMBING PRODUCTS 61 THE SOURCE 62 CALENDAR

MH22

IN-FLOOR RELIABLE STORAGE In-floor solution works for agriculture fertilizer warehouse.

MH24

HEAT PUMPS CUT OUT THE CUT-OUT QUESTIONS Path towards a low carbon future will include heat pumps for buildings.

MH26 PRODUCT SHOWCASE MH28

EMMITERS ADJUSTING FOR CONDITIONS Formulas for sizing panel rads to accommodate low-temp water.

AUGUST 2021 | HPAC

3

ADVERTORIAL

The 2021 Ford F-150 The F-150 that’s tougher, smarter, and more productive than ever before.

Y

our business is your top priority, so when you’re looking for a truck, you don’t want to settle for second-best. You want a truck that offers bestin-class*,† capability to help you get the job done, plus class-exclusive^ features that make every job easier. You want the Ford F-150, the 2021 North American Truck of the Year.

Re-engineered from the ground up, and redesigned both inside and out, the F-150 delivers toughness and innovative technology to help change the way you work.

BEST-IN-CLASS FOR YOUR BUSINESS When Ford set out to redesign their best-selling truck, they didn’t cut corners. It’s why the 2021 F-150 offers best-in-class* max. available towing of 14,000 lbs., and best-in-class† max. available payload of 3,325 lbs.

There’s also a new class-exclusive^ 3.5L PowerBoost™ Full Hybrid V6 that offers the most torque ever in an F-150.

And delivers maximum available conventional towing of 12,700 lbs.‡ POWER WHERE YOU NEED IT The 2021 F-150 is also available with class-exclusive^ Pro Power Onboard™ which offers exportable power on demand in 2.0 kW/2.4 kW/7.2 kW options. So, when you need to power up your equipment on the worksite, you can plug it directly into your F-150.

YOUR SMART NEW OFFICE We know that when you use a truck for business, it’s also your mobile office. The all-new interior of the F-150 is designed to help keep you productive, connected, and comfortable, no matter how long your day lasts.

It comes standard with SYNC®4** and has an available 12” Touchscreen giving you complete control of all the innovative tech in the F-150. From enhanced voice recognition, to cloud-based connectivity, your new office

will work harder than ever before.

The 2021 F-150 is also available with a new stowable shifter and centre console that folds down to create an Interior Work Surface for your laptop or even a quick lunch.

BUILT TOUGH FOR YOUR BUSINESS Tougher and smarter than ever before, the F-150 is designed to work as hard as you do. When you’re looking for the best to help you build your business, you want the truck that’s Built Ford Tough. The 2021 F-150. Part of F-Series, Canada’s best-selling line of pickup trucks for 55 years‡‡.

LEGAL Vehicle may be shown with optional features. * Maximum towing on 2021 F-150 SuperCab 8’ box and SuperCrew 4x2 with available 3.5L EcoBoost, Max Trailer Tow Package. Class is Full-Size Pickups under 8,500 lbs. GVWR. Max towing varies based on cargo, vehicle configuration, accessories, and number of pessengers. Towing and payload are independent attributes and may not be achieved simultaneously. † Maximum payloadn on 2021 F-150 Regular Cab 8’ box 4x2 with available 5.0L V8 engine and Max Trailer Tow and Heavy-Duty Payload packages. Class is Full-Size Pickups under 8,500 lbs.

GVWR. Max payload varies and is based on accessories and vehicle configuration. See label on door jamb for carrying capacity of a specific vehicle. Towing and payload are independent attributes and may not be achieved simultaneously. ^ Class is Full-Size Pickups under 8,500 lbs. GVWR. ‡ When properly equipped. ** Some mobile phones and some digital media players may not be fully compatible. Don’t drive while distracted. Use voice-operated systems when possible; don’t use handheld devices while driving.

Some features may be locked out while the vehicle is in gear. ‡‡ F-Series is the best-selling line of pickup trucks in Canada for 55 years in a row based on Canadian Vehicle Manufacturers’ Association statistical sales report up to year end 2020. ©2021 Ford Motor Company of Canada, Limited. All rights reserved.

With a full range of Built Ford Tough® Commercial Vehicles, we make it easy to choose the one that’s right for your business. From the endless versatility of Transit and Transit Connect to the legendary power and capabilities of F-Series, you’ll nd a dependable partner that’ll get to work – day in and day out.

2021 TRANSIT

KEY FEATURES Super Duty® has best-in-class max. available payload of 7,850 lbs* F-150 has class-exclusive^ available Pro Power OnboardTM that offers exportable power on demand Transit has 3 lengths, 3 heights and multiple cargo congurations

2021 SUPER DUTY

2021 TRANSIT CONNECT

FORD.CA/COMMERCIAL-TRUCKS

2021 F-150

Transit Connect has a compact footprint, and a max. cargo space of 145.8 cu ft†

Vehicles may be shown with optional features. *2021 Super Duty with 6.2L engine, DRW, Long Box and Heavy-Duty Payload Package. Class is Full-Size Pickups over 8,500 GVWR. Max. payload is for properly equipped base vehicle with required equipment and a 150-lb driver and varies based on cargo, vehicle conguration, accessories and number of passengers. See label on door jamb for carrying capacity of a specic vehicle. For additional information, see your Ford Dealer. ^Class is Full-Size Pickups under 8,500 lbs GVWR. †Cargo and load capacity limited by weight and weight distribution. ©2021 Ford Motor Company of Canada, Limited. All rights reserved.

< UPFRONT MOST VALUABLE RESOURCE THESE DAYS PLUMBING AND HVAC/R CONTRACTING COMPANIES OF ALL SIZES SHARE COMMON CONCERNS about keeping safe during this ongoing pandemic, maintaining a steady flow of business and maybe most importantly ensuring they can not only attract new qualified workers to keep up with the workload, but to retain the existing teams they’ve built over the years.

In speaking with a few business owners recently, they really emphasized the measures they are taking to ensure the work environment they can control meets the needs of their employees, especially the “younger” generation.

One HVAC/R business owner in Ontario talked about actually scheduling a “company day” to break free from the routine and go axe throwing, go-carting or some other group activity.

Another business owner on the west coast talked about the “generational shift” and stressed how important it is to keep the team outfitted with the very latest equipment. It keeps the technicians current and shows you’re keeping the business on the leading edge and relevant.

One article I recently read online about the most profitable businesses in construction emphasized how the best firms are serious about finding, attracting, and retaining the best people. They become a destination employer that attracts highly qualified labour.

The people I’ve spoken with have said you have to remain competitive with respect to compensation, but that’s just a given, you also need a strategy around retention and that includes employee development.

The leading companies look out for ways to include and improve their people through industry training opportunities. In the plumbing and HVAC/R world industry education never stops, that’s why manufacturer and industry association training, along with the helpful assistance that trade journals like HPAC Magazine provide, remain valuable tools to share with tradespeople.

We hope that our efforts to inform through printed pages, online news and articles, and more recently with our 30 Mechanical Minutes videos, we can be an additional resource included in every plumbing and HVAC/R business’s growth and employee retention strategy.

A business is truly only as good as its people, and to be a leader in your field requires making the effort to engage and communicate with your teams to ensure you're providing a work environment they can grow with.

On that note, I would like to introduce the newest member to our HPAC team: Logan Caswell has joined us an Associate Editor. With a journalism Diploma from Durham College in Oshawa, Ont., Logan comes to us after some field experience in the broadcast media and also marketing and social media sectors. He’s already been reaching out to the HPAC community, and once industry events start rolling again you can ex- Logan Caswell pect to see him around in person. If you have any words of wisdom or encouragement to share with someone new to the plumbing and HVAC/R world, please feel free to reach out and welcome this new face to the industry: lcaswell@hpacmag.com. <> Doug Picklyk, Editor 6

HPAC | AUGUST 2021

Reader Service Print and digital subscription inquires or changes, please contact Urszula Grzyb, Audience Development Manager Tel: (416) 510-5180 Fax: (416) 510-6875 Email: ugrzyb@annexbusinessmedia.com Mail: 111 Gordon Baker Rd., Suite 400, Toronto, ON M2H 3R1

EDITOR Doug Picklyk (416) 510-5218 DPicklyk@hpacmag.com ASSOCIATE EDITOR Logan Caswell (416) 728-6209 LCaswell@hpacmag.com ASSOCIATE David Skene (416) 510-6884 PUBLISHER DSkene@hpacmag.com MEDIA DESIGNER Emily Sun esun@annexbusinessmedia.com ACCOUNT Kim Rossiter (416) 510-6794 COORDINATOR krossiter@hpacmag.com

PUBLISHER Peter Leonard (416) 510-6847 PLeonard@hpacmag.com COO Scott Jamieson sjamieson@annexbusinessmedia.com

PUBLICATIONS MAIL AGREEMENT NO. 40065710 Heating Plumbing Air Conditioning (established 1925) is published 7 times per year

by Annex Publishing & Printing Inc. HPAC Magazine is the leading Canadian business publication for the owner/manager of mechanical contracting businesses and their supply partners.

ISSN: 0017-9418 (Print) ISSN 2371-8536 (Online) Contents Copyright © 2021 by Annex Publishing & Printing Inc. may not be reprinted without permission.

SUBSCRIBER SERVICES: To subscribe, renew your subscription or to change your address or information please visit us at www.hpacmag.com.

Subscription Price per year: $44.00 (plus tax) CDN; Outside Canada per year: $112.00 US; Elsewhere: 1 year $123.00 (CDN); Single copy Canada: $5.00 CDN. Heating Plumbing Air Conditioning is published 7 times per year except for occasional combined, expanded or premium issues, which count as two subscription issues.

MAIL PREFERENCES: From time to time we make our subscription list available to select companies and organizations whose product or service may interest you. If you do not wish your contact information to be made available, please contact us via one of the following methods: Tel: 416-442-5600 ext. 3552, Fax: 416-510-6875 or 416442-2191; E-mail: blao@annexbusinessmedia.com; or by mail: 111 Gordon Baker Rd., Suite 400, Toronto ON M2H 3R1 Annex Privacy Officer Privacy@annexbusinessmedia.com Tel: 800-668-2374 HPAC Magazine receives unsolicited materials (including letters to the editor, press releases, promotional items and images) from time to time. HPAC Magazine, its affiliates and assignees may use, reproduce, publish, re-publish, distribute, store and archive such unsolicited submissions in whole or in part in any form or medium whatsoever, without compensation of any sort.

NOTICE: HPAC Magazine, Annex Publishing & Printing Inc., their staff, officers, directors and shareholders (hence known as the “Publisher”) assume no liability, obligations, or responsibility for claims arising from advertised products. The Publisher also reserves the right to limit liability for editorial errors, omissions and oversights to a printed correction in a subsequent issue. HPAC Magazine’s editorial is written for management level mechanical industry personnel who have documented training in the mechanical fields in which they work. Manufacturers’ printed instructions, datasheets and notices always take precedence to published editorial statements.

Proud member of:

www.hpacmag.com

HPACMAG.COM

NEWS FEATURE

SEE THE LATEST NEWS @ HPACMAG.COM

LEADING A YOUTH MOVEMENT

PHOTO: SHERRY SMITH PHOTOGRAPHY

BY LOGAN CASWELL

In May the Canadian Apprenticeship Forum released the Apprentice Demand in Red Seal Trades report which estimates that 163,785 new journeypersons will be required from 2021 to 2025 in order to sustain workforce certification levels across 56 Red Seal trades in Canada. To meet that anticipated demand, the country will need a to- Rachel Hesketh, working to tal of 375,026 apprentices over the raise the profile of women and youth in the trades. next five years.

Filling the gap requires getting more youth interested in the trades and specifically attracting more women. One initiative, being led by CAF, is called Support Women in Trades (SWiT), a national strategy with a goal of increasing the proportion of women across all trades to 15% by 2030, up from a baseline of 4.5% recorded in 2018.

Plumbing and HVAC/R remain typically male-dominated, and while change and support is being encouraged from industry organizations, some individuals are leading from within. Rachel Hesketh, a 29-year-old plumbing journeyperson, recently completed her five-year training program, and now the Hamilton resident is spearheading a youth committee within her union (UA-Local 67) to engage young women to get excited and participate in the skilled trades. We spoke with Hesketh to gain perspective on her journey so far.

What led to the launch of the youth committee? It came through my volunteering. I was a part of other committees and saw what was possible. I noticed the interest in getting more women in trades, so I thought it was important to take advantage of it and create the committee called Evolve.

What led you to get into this industry? Before this I was on the path of becoming an early childhood educator, so the change in paths happened quite quickly. I came across a preapprenticeship program that aimed to get women into the trades with UA-LOCAL 67. At the end of the program, we had an opportunity for a job placement, and if all went well you received an opportunity to join the union. So it provided me with a lot of drive and motivation to succeed.

What are the obstacles to getting more women and youth into mechanical contracting? Raising our visibility and overcoming the common stigma of going to university instead of going into trades. You can go to school for years, or you can go work in a trade, do a five-year pre-apprenticeship program and make money along the way.

What inspired you to make this your career? Through the grind of my pre-apprenticeship program I realized the joy I would get from making this into a real-time career. Seeing progress with yourself was the biggest thing for me. Every day is different, you learn as the days and weeks go on. It’s super encouraging to come onto a job site and instantly know a solution and be able to help others who need your assistance in certain situations.

HPACMAG.COM

What is Evolve? Evolve is a committee of youth members to encourage people under 35 to participate in helping forward their careers and help young people express their questions about their own union and the benefits involved.

It’s not just a local youth committee, it’s a national youth committee. Our goal is to network with members and participate with community outreach—however we can help everybody.

What goals are you trying to achieve as a woman in trades? Being visible and making people know that we’re there. This past week [on a jobsite there were] three women working, and I was shocked in happiness. But three really isn’t enough, and if we can continue to show we’re happy to be there that number should only grow.

What have your experiences been like? I have had some challenges along the way, but I am grateful, and it’s always good having people to support you. Being the only girl on a job site several times; it’s hard to feel like you belong. But as time goes on, we’re seeing more and more women so it makes you feel reassured.

How do you feel about your career choice today? I love it.

You can drive down a road and see a building you worked on and point it out and feel proud about the work you did.

What’s your advice to young people? If you have an opportunity to do a pre-apprenticeship program, do it, because you will have the chance to see if you really like it. There are numerous network opportunities you can take part in and take advantage of union courses. Don’t be afraid of how long apprenticeship programs take because it will be worth it in due time. <> AUGUST 2021 | HPAC

7

INDUSTRY NEWS SEE THE LATEST NEWS @ HPACMAG.COM

8

HPAC | AUGUST 2021

Winning photo in the backflow tester category.

The backflow didn’t pass and already had a note saying it failed two years prior.

Xavier Lamoureaux, backflow tester with prize.

Inspector category winning photo

2021 BAD AND UGLY CROSS CONNECTION CONTROL CONTEST WINNERS ANNOUNCED The Cross Connection Control Committee of the Western Canada Section, American Water Works Association (WCS AWWA) announced the winners of its annual “Bad and Ugly” contest: Xavier Lamoureaux of saint-Hubert, Quebec in the backflow tester category; and Robert Glowacki from Winnipeg in the inspector category.

The contest invites testers and inspectors to submit photos of troubled installations with the goal of raising greater awareness of cross connections and to educate other water industry representatives in the field.

“The WCS AWWA CCC committee would like to extend our thanks to all the testers and inspectors who submitted their bad and ugly photos and congratulations to the 2021 winning photos,” notes Danny Wilson, WCS AWWA CCC Education Committee member, who also thanks the backflow manufacturers Conbraco, Watts and Zurn who provide the contest prizes.

For 2022 contest entry details visit wcsawwa.net.

Quebec: Rénoclimat 1-866-266-0008; renseignements.te@mern.gouv.qc.ca nrcan.gc.ca STUDY HIGHLIGHTS CHALLENGE IN RETAINING APPRENTICES Statistics Canada released a new study looking at certification rates for apprentices who began their training in 2013 and where they were in 2019.

While program durations vary by province and trade, the most common program duration for all trades at the national level is four years. In 2017, four years after registration, approximately one-fifth (20.9%) of the 2013 cohort of apprentices had completed their training and one-third (35.4%) had discontinued. By 2019, just under one-third of

apprentices had certified, while almost half had discontinued (45.4%).

In 2019, six years after registering in their programs, certification rates were highest among Red Seal trades—of note: plumbing (35.1%) and refrigeration & AC mechanic (40.9%).

The study also states apprentices who were undergoing training or close to certifying may have faced obstacles in their training and in the labour market because of the COVID-19 pandemic as many ministries of training and educational institutions closed. The pandemic also had an impact on registrations and certification rates in 2020, adding to the shortage of certified tradespeople in Canada. statcan.gc.ca HPACMAG.COM

PHOTOS SUPPLIED COURTESY WCS AWWA

FEDS LAUNCH CANADA GREENER HOMES GRANT The Government of Canada officially launched the new Canada Greener Homes Grant, offering homeowners the ability to receive grants of up to $5,000 to make energy efficient retrofits to their primary residences.

Eligible upgrades include improving heating and cooling systems—such as with heat pumps—replacing windows and doors, adding insulation, sealing air leaks, and purchasing renewable energy systems like solar panels. As part of the program, all mechanical and electrical systems, with the exception of thermostats, must be installed by a licensed and trained professional.

The government program will help up to 700,000 Canadian homeowners and in total includes an investment of $2.6 billion over seven years.

In addition to the $5,000 grant, up to $600 is available for the cost of home energy evaluations.

The grant is retroactive to December 1, 2020, and homeowners go online to register, plan, and document their progress, which includes applying for their pre-retrofit evaluation, choosing from a list of eligible retrofits, scheduling a post-retrofit evaluation, and applying for reimbursement.

Residences include single and semidetached houses, row housing, townhomes, mobile homes on a permanent foundation, permanently moored floating homes, small multi-unit residential buildings (up to three storeys with a footprint of up to 600m2), and mixed-use buildings (residential portion only).

Residents of Quebec and Nova Scotia need to apply directly through their provincial programs to book their EnerGuide evaluation.

Nova Scotia: Home Energy Assessment 1-877-999-6035, info@efficiencyns.ca, www.efficiencyns.ca/residential/

CANADIAN PROPANE ASSOCIATION INTRODUCES NEW BRAND IDENTITY The Canadian Propane Association (CPA) is celebrating its 10th anniversary with a new brand identity that is designed to convey propane as an essential part of Canada’s low carbon economic future.

According to the association, the decision to update the brand was out of the need for visual expression to convey today’s industry — modern, versatile, and reliable.

RMC INCREASES FEE ON CFC-11 REFRIGERANT DISPOSAL Refrigerant Management Canada (RMC) has announced the fee for accepting CFC11 refrigerant (Trichlorofluoromethane, also called freon-11 or R-11) into the program has changed.

As of July 1, 2021, the new fee became $20/kg for CFC-11 refrigerant entering the program for destruction.

The change comes after the RMC Board of Directors decided that the cost of collecting and destroying CFC-11 refrigerant can no longer be subsidized by the program, as their costs continue to increase.

RMC recommends that contractors discuss the disposal fee with their customers and remind them that as the equipment and refrigerant owner, they are obliged to comply with the provincial and federal regulations regarding the proper handling, storage and disposal of CFC-11 refrigerant. hrai.ca HPACMAG.COM

RIGHT TIME GROUP EXPANDS REACH TO ALBERTA Right Time Group of Companies is on a roll. The residential HVAC contractor group owned by San Francisco-based private equity firm Gryphon Investors with regional locations in Ontario, Manitoba and B.C., now has a foothold in Alberta and has strengthened its position in Ontario with the acquisition of two more companies in recent months.

In April Right Time acquired Edmonton-based Romaniuk Heating and Air Conditioning, and the expansion continued in June when Comfort Masters Ltd. in Ontario became Right Time’s seventh acquisition. Comfort Masters provides residential HVAC, air quality and hot water services to the Oshawa, York, Durham and Simcoe regions of the province.

Right Time is focused on developing a national brand through acquisitions or partnerships with existing residential HVAC replacement contractors. right-time.ca THE ARCTICOM GROUP ENTERS THE CANADIAN MARKET The Arcticom Group (TAG), a commercial and industrial refrigeration company, has announced its expansion into the Canadian HVAC/R market with three acquisitions: CT Control Temp and its sister company IHM Mechanical, located in Vancouver; and CTR Refrigeration & Food Store Equipment with locations in Calgary and Edmonton.

Based in California, TAG has been expanding over the past three years by acquiring independent HVAC/R companies. thearcticomgroup.com <>

RETHINK YOUR UPFIT. RECHARGE YOUR BUSINESS. TOUGH JOBS CALL FOR TRUSTED PARTNERS.

At Adrian Steel, we do more than just create high-quality products. We look at the big picture, taking into account all of your business needs and the way you work in and out of the van.

Then, we provide you with custom solutions that make your job easier and give you the biggest ROI possible.

To learn more and locate your nearest distributor, go to adriansteel.com/distributors

AUGUST 2021 | HPAC

9

< HVAC

VENTILATION: WHO NEEDS IT? As new standards lead to tighter building envelopes, homes require mechanical ventilation solutions. BY IAN McTEER

T

10

HPAC | AUGUST 2021

Along with more energy-efficient HVAC appliances another trend has led to sealing houses up as tight as possible with tight-fitting windows, doors, vapour barriers and cans of expanding foam insulation.

In one study of a 90’s era residential renovation, the house in question was depressurized beyond 50 pascals once all the air exhausting appliances were running. That’s 10 times more depressurization than allowed, especially with buoyancy vented fossil fueled appliances inside the structure.

MECHANICAL VENTILATION WHAT KIND OF AIR? With today’s tighter building envelopes we need to consider how to introduce air inside and why. And we might need

Modern houses and commercial buildings pay much greater attention to air and moisture leaking either into or out of the building, and with standards HPACMAG.COM

PHOTO: YARASLAU SAULEVICH/ISTOCK/GETTY

he simple answer to the headline of this article is anyone (human or animal) living and working indoors. The larger question is how we go about providing enough fresh oxygenated air for building inhabitants while maintaining reduced levels of HVAC energy consumption as prescribed by current governmental regulations.

Inspired by the fall-out of an oil embargo in the early 1970s, the U.S. Department of Energy (DOE) embarked on an all-encompassing energy security program that led to North American regulators developing ever-increasing HVAC efficiency standards or Minimum Efficiency Performance Standards (MEPS).

several kinds of air. Normally there’s only one type of air, but inside a building we need the air to do different things depending on the indoor activities.

Ventilation air is the most important kind for humans and animals. Humans respire some 30 lbs. of air daily while we spend almost 90% of our lives indoors. At the same time, it is necessary to get rid of excess moisture, odours, carbon dioxide, ozone, particulates and other noxious compounds from our indoor environment. And while opening a window provides needed ventilation air, this unregulated ventilation will cause HVAC systems to consume excessive amounts of energy—energy we’re supposed to be saving.

Make-up air is the air coming in from outside intended to replace that air being exhausted by devices such as range hoods and bathroom fans, central vacuum systems and clothes dryers.

Today’s homes that are being built to the latest codes probably do not need make-up air anymore unless oversized range hoods moving large air volumes (more than 200 cfm) are installed by overzealous chefs.

Finally, there is also combustion air, the air meant to be used with fossil fueled appliances such as gas furnaces, water heaters, stoves and wood burning fireplaces. By filling every conceivable air leakage gap in today’s homes, gas appliances must “borrow” ventilation air thus creating a dangerous problem. Appliances unable to vent due to depressurization, or starved for air, could start to burn their own flue products creating deadly carbon monoxide, a tragedy that has ended the lives of too many people over the years.

Typical components of an HRV system.

SOURCE: NRCAN PUBLICATION (2012): HEAT RECOVERY VENTILATORS

Example diagram of an HRV installed with a forced air furnace system

such as LEED, Passive House and Net Zero, houses are tight and the building envelope is sealed with an air leakage goal of no more than 1ACH50 (one air change per hour at 50 pascals). I’ve seen one Passive House consultant boast of 0.14ACH50.

And today’s HVAC systems are better designed with gas furnaces and water heaters using outdoor air for combustion, so life is good, no? Maybe not so good, as we are still seeing rules of thumb making the rounds especially in renovation jobs where ventilation systems are often oversized, and powerful range hoods can still suck nearly every HPACMAG.COM

molecule of air out of the house forcing would-be chefs to open a window.

INTRODUCING HRV AND ERV Older buildings were so leaky that infiltrating air met all the ventilation requirements with ease, but not without penalties. Incoming air needed to be conditioned with heat and maybe humidity incurring extra costs for fuel and maintenance. Houses were drafty, occupants often felt uncomfortable as dry air evaporated excessive amounts of moisture from the skin creating a feeling of being too cold. Static electricity build-up in carpets and furnishing

caused painful shocks when the electrically charged homeowner touched a grounding surface. So, which is better?

A borderline leaky 2,100 sq. ft. threebedroom house rated at 3ACH50 will, according to the ASHRAE 62.1 and 2, require 93 cfm of outdoor air based on the formula: Quantity of air (Q) = 7.5 cfm/occupant + 3 cfm/100 ft2 of living area Thus, Q = 7.5 cfm x 4 occupants + 3 cfm/100 ft2 = 93 cfm (example calculation by Denis Boyer, M.Eng.) A heat recovery ventilator (HRV) is a mechanical ventilation solution that will use the stale exhaust airstream to preheat the same volume of cold entering outdoor fresh air.

As the airstreams pass each other within the core of the HRV, upwards of 75% or better of the indoor air heat will be transferred to the colder air thus providing needed ventilation while reducing the cost of “making up” the heat required to bring that fresh air up to ambient room temperature.

In humid geographies, in the summer months an HRV will increase the humidity level in the house. With a cooling unit in operation and the windows closed, the house still needs adequate ventilation. A properly sized cooling system designed with the summer latent load in mind should be able to deal with the extra humidity, admittedly, at an extra cost.

An ERV, or energy recovery ventilator, operates in a similar fashion to the HRV, but during the winter some of the humidity in the air is returned to the indoor space. Ideally, in tighter houses, an ERV will help to retain indoor humidity in the 40% range countering the uncomfortable and unhealthful effects of dry wintertime air.

Summer operation has the ERV reject as much as 70% of the incoming humidity sending it back outside before it can load-up the cooling system.

An ERV does not act as a dehumidifier.

Continued on p12 AUGUST 2021 | HPAC

11

< HVAC

Continued from p11

ERV’S ARE BETTER FOR A HUMID CLIMATE

INSTALLATION CONSIDERATIONS While ERV/HRV units designed for residential installation can be installed in a simplified fashion using the existing air handling system to distribute the conditioned air, do not do it that way if possible.

In my opinion, it is best to install a fully dedicated duct system in new construction or complete renovation jobs. The 12

HPAC | AUGUST 2021

Example diagram of an HRV with direct ductwork

building will benefit from the best possible conditioned air distribution and the lowest possible operating cost, as the furnace or air handler fan will not be needed.

Some of the best HRV/ERV equipment on the market feature EC motors and control algorithms capable of automatically balancing the systems and adapting to pressure changes. Optional MERV 13 filtration is available and a TURBO mode lasting up to four hours helps to remove odours, and in dedicated situations can help provide needed ventilation for an isolated sick room.

It may take some time to convince all homeowners that mechanical ventilation is truly superior to open windows at any time. Urbanites truly have a vested interest in relying upon professionally installed and well-maintained mechanical ventilation, something, as studies suggest, they have never had before.

Mea Culpa: I live in a rural area, certainly not free of dust and other contaminants from outside, however, on nice lowhumidity days of reasonable temperature we typically open the windows regardless of my HRV and fancy air cleaner.

At night we can hear the Barred Owls hooting, the leaves rustling in the trees and the spring peepers frantically chirping; it is all comforting in a way. And even in winter, my wife of many years insists on keeping a window open, just a crack!

Perhaps there will come a day when windows only open for emergencies, and one’s view of the outdoors will come from giant OLED screens. Whatever the future may hold, improvements to indoor air quality will never come too soon. <> Ian McTeer is an HVAC consultant with 35 years of experience in the industry. He was most recently a field rep for Trane Canada DSO. McTeer is a refrigeration mechanic and Class 1 Gas technician.

HPACMAG.COM

SOURCE: NRCAN PUBLICATION (2012): HEAT RECOVERY VENTILATORS

Ventilation experts will say the ideal mechanical ventilation unit for any home is dependent on the local climate, lifestyle of the occupants and the owner’s specific needs. For example, in houses where the wintertime humidity level tends to rise above 55%, an HRV would do a better job of removing excess humidity.

Experts also agree that newer houses, or those renovated to the latest building code, should have an ERV specified since buildings equipped with triple glazed windows and properly insulated basements can support a higher relative humidity in the winter months: 35% +/- 5% is acceptable.

I was recently listening to a presentation by Gord Cooke of Building Knowledge and he reminded me that modern housing experiences different HVAC loads from yesteryear.

Specifically, sensible loads are going down while latent loads are increasing for several reasons, for example: • Moisture created by occupants and their activities: up to 12 liters per day from a family of four.

• Moisture coming inside due to natural leakage: upwards of 20 liters per day (loose construction 3ACH50) .

• Moisture coming inside via mechanical ventilation: 40 to 50 liters per day at 120 cfm ventilation.

• I’ll add another aspect from my experience—too many people fail to service their HRV’s, many were not installed properly and, all too often, the unit is simply turned-off during the summer. With windows opened for fresh air, the cooling system must work overtime to not only reject uncomfortable sensible heat at bedtime (windows closed) but will decidedly blow the budget on dealing with the latent load that will become the most difficult and time-consuming task of the overburdened cooling system.

If excess ventilation air via oversized equipment or “windows open strategy” occurs, humidity levels will easily exceed 50% in humid climates. As Cooke mentioned in his lecture, when the moisture content of air is measured at 50%RH and the air temperature is 23C, then the dew point temperature will be 12.1C (53.8F). Now the sizing of the air conditioning unit and its latent capacity becomes crucial. An oversized AC unit, or too much air over the evaporator coil, or an improperly specified unit, may put air off the evaporator coil above dew point – in other words, no dehumidification!

Maestro Wi-Fi App available

< VENTILATION

HRVS AND ERVS EXPLAINED A recent HPAC Magazine webinar discusses the role of mechanical ventilation systems in buildings and shares some best practices for contractors. BY LOGAN CASWELL

T

he latest instalment of HPAC Magazine’s 30 Mechanical Minutes focused on ventilation, with regular HPAC writer Ian McTeer joined by Ryan Carr, Business Development and Technical Lead with Air Solutions. The main topics of discussion centered around heat and energy recovery ventilation systems (HRVs and ERVs). The episode was sponsored by TSI Inc.

HRV, ERV BASICS Carr explained how modern homes are unlike our grandparent’s drafty houses, and as buildings are no longer constructed to leak heat and moisture they need ventilation of some kind to filter and refresh the stale inside air.

“In our quest for energy efficiency we have tightened up that [building] envelope and we no longer have that natural heat exchange,” said Carr. “So we have to give the house lungs.”

A heat recovery ventilator (HRV) uses the heat in the outgoing stale exhaust air to preheat the incoming air. However, Carr explained that as envelopes have become even tighter, “It’s less about the heat loss/heat gain anymore, and more about the moisture.”

That’s why energy recovery ventilation systems (ERVs) have become more prominent. Not only is the sensible heat addressed, but the system also captures the latent heat (or the moisture) in the air. That means seasonally, in colder climates such as Canada, an ERV transfers the humidity from the air which has 14

HPAC | AUGUST 2021

Panelist Ryan Carr explains the principles behind the operations of an ERV core which benefits indoor humidity control in buildings.

been conditioned indoors to the incoming cold bone-dry air and also keeps it at an ambient temperature. While in humid hot weather months excess humidity is kept outdoors. This creates a better indoor environment and ultimately energy savings for the consumer.

SIZING UNITS In most new residential installations, a simple bedroom count is generally all that’s needed to calculate what size of HRV or ERV unit should be installed.

“Frankly, we don’t really care about square footage,” said Carr. “Because bedrooms are a good indicator of the number of occupants in the house, as they are the ones needing the fresh air.” Carr went on to say contractors can now right-size equipment with a typical three-bedroom family home only needing a 64 cubic feet/minute (cfm) unit for continuous ventilation.

On the commercial building side, McTeer pointed out how the multitude of applications from swimming pools to restaurants and office spaces to gymnasiums complicated the whole process of ventilating a building. The recent pandemic, which drove workers away from commercial buildings to work from home, has highlighted the need to create a healthier environment the workplace.

“Often you hear the term sick building syndrome,” said McTeer. “A lot of it has to do with the fact commercial buildings are very poorly or sometimes overly ventilated to the point where the relative humidity drops to under 10% in some cases. This causes people a lot of grief.” He referred to a recent article about those working from home because of COVID are delighted because their allergies, stuffy nose and dry skin issues have been reduced and they Continued on p16 HPACMAG.COM

R

SC EDI

OV E R T HE

great indoors With the AirAssure™ Indoor Air Quality Monitor

Amazing things happen when we’re in the same place — and with the new TSI AirAssure™ IAQ Monitor, you don’t have to wonder about your indoor air quality. This economical, user-friendly device measures what you need to know about your indoor environment and places the information at your fingertips in real-time. This data can help you make informed facility decisions and confidently welcome people back indoors.

To learn more, visit tsi.com/AirAssure.

< VENTILATION

Continued from p14

don’t want to go back to the office.

INSTALLATION PRACTICES Carr outlined three dominant installation methods for HRV/ERV systems: Simplified – where the unit is hung in the mechanical room and air is inducted in and out of the return air ducts.

Exhaust ducted – the unit is pulling from high moisture areas of concern— laundry room, bathrooms, and kitchens.

Fully ducted – in this installation method dedicated exhaust ports in those areas of high humidity are combined with supply ducts into common areas such as hallways, bedrooms and family rooms. Eventually the air reaches an equilibrium throughout the building.

BEST PRACTICES It is crucial these systems are balanced when installed: too much supply versus

exhaust could drive moisture into the walls. “As that moisture moves its way into the outside of that wall it’s going to get cooler, and it may condense inside that wall. It can lead to mold, mildew or rot,” said Carr. Conversely, too much negative air pressure will lead to infiltration of unconditioned air which also increases the risks of mold and higher energy costs. There is also a potential of back draft from combustion appliances, chattering dampers and hardto-open doors.

MAINTENANCE REQUIREMENTS Installing an ERV or HRV is an opportunity for service contractors to add another line to the invoice for annual maintenance. Services include cleaning or replacing prefilters, ensuring the condensate line is clear (HRVs), and checking exterior hoods. <>

Q&A

Questions posed by webinar viewers: How can one find a proper balance in a drier home in the winter?

McTeer: An ERV is the best choice as it retains a minimal amount of humidity, eliminating the cost of power to run a humidifier.

Are there any emerging technologies on the way?

Carr: New technologies such as zone register terminals installed in highconcern areas of the house such as laundry rooms, bathrooms and kitchens can be turned on with the switch of a button. The switch would-open a dedicated fan for the specific area while shutting the other areas off, enabling a focused suction to that room.

Both McTeer and Carr answered additional viewer questions, to see the entire recorded video visit: hpacmag.com/tech-pulse.

IT’S TIME TO COOL DOWN WITH KEEPRITE ENJOY COMFORT WITHOUT COMPROMISE Ion™ 19 Variable-Speed Air Conditioner - TVA9 • Up to 19 SEER • Up to 13 EER • As low as 56 decibels • 5-stage operation • Wi-Fi® enabled remote access • 10-Year No Hassle Replacement™ Limited Warranty For more information about our entire product line-up, visit us at keeprite.com

16

HPAC | AUGUST 2021

HPAC_ICP_June21.indd 1

HPACMAG.COM

2021-05-20 11:39 AM

MODERN HYDRONICS 2021 FALL

WAREHOUSE IN-FLOOR INSTALLATION SIZING PANEL RADS FOR LOW WATER TEMPS

SWEET HEAT 2021 This year’s contest-winning projects

PLANNING MULTI-ZONE LAYOUTS BOILER CHEMISTRY CONSIDERATIONS

a publication of

It’s easy to spot why Navien will be the best selling condensing tankless.*..again 2'' PVC up to 75 feet and 1/2'' gas up to 24 feet

*Navien NPE Series is the best selling condensing tankless water heater according to BRG.

High efficiency – up to

0.96 UEF and up to

15:1 TDR

Durable dual stainless steel heat exchangers

ComfortFlow NPE-A2 internal buffer tank and recirc pump ®

Optional NaviCirc - easy to install with no recirc return loop needed TM

EZNav multi-line control with built-in intuitive software TM

Built-in HotButton on-demand capability

TM

New Navien NPE-2

High efficiency condensing tankless water heaters The best just got even better To learn more visit NavienInc.com Navien Canada is now a proud strategic partner of

The leader in condensing technology...does it again.

STRATEGIC PARTNERS

CONTENTS

Modern Hydronics

MH20 DESIGN Water Works

The new headquarters for the Toronto and Region Conservation Authority will showcase its mechanical system.

By Doug Picklyk

MH22 IN-FLOOR

In-floor Provides Reliable Storage

MH4 AWARDS

Radiant heating used for temperature and condensation control in agricultural fertilizer warehouse.

Sweet Heat Awards 2021 Celebrating the top residential and commercial entries in HPAC Magazine’s first-ever Sweet Heat hydronics installation competition.

By Logan Caswell and Doug Picklyk

MH24 HEAT PUMPS

Cut it Out with the Cut-Out Questions

MH10 PIPING

Old ways of thinking are not compatible with a low carbon future.

By Chris DesRoches

Zoning Considerations What to think about when planning your system layout.

By John Siegenthaler

MH26 PRODUCT SHOWCASE MH28 EMMITERS

MH14 BOILERS

Optimizing Boiler Chemistry

Adjusting for Conditions

In this edition of 30 Mechanical Minutes panelists review why maintaining proper water chemistry is essential with modern boiler systems.

By Logan Caswell

How to size panel radiators for low water temperatures.

By John Siegenthaler

MODERN HYDRONICS

a supplement of Heating Plumbing Air Conditioning Magazine

111 Gordon Baker Road, Suite 400, Toronto, ON M2H 3R1 TEL: 416.442.5600 FAX: 416.510.5140 www.hpacmag.com

EDITOR ASSOCIATE EDITOR ASSOCIATE PUBLISHER ACCOUNT COORDINATOR MEDIA DESIGNER CIRCULATION MANAGER PUBLISHER COO

WWW.HPACMAG.COM

HPAC Magazine receives unsolicited materials (including letters to the editor, press releases, promotional items and images) from time to time. HPAC Magazine, its affiliates and assignees may use, reproduce, publish, re-publish, distribute, store and archive such unsolicited submissions in whole or in part in any form or medium whatsoever, without compensation of any sort.

Doug Picklyk (416) 510-5218 DPicklyk@hpacmag.com Logan Caswell (416) 728-6209 LCaswell@hpacmag.com

NOTICE: HPAC Magazine, Annex Business Media, their staff, officers, directors and shareholders (hence known as the “Publisher”) assume no liability, obligations, or responsibility for claims arising from advertised products. The Publisher also reserves the right to limit liability for editorial errors, omissions and oversights to a printed correction in a subsequent issue. HPAC Magazine’s editorial is written for management level mechanical industry personnel who have documented training in the mechanical fields in which they work.

Manufacturers’ printed instructions, datasheets and notices always take precedence to published editorial statements.

David Skene (416) 510-6884 DSkene@hpacmag.com Kim Rossiter (416) 510-6794 KRossiter@hpacmag.com Emily Sun esun@annexbusinessmedia.com

Contents Copyright © 2021 by Annex Publishing & Printing Inc. may not be reprinted without permission.

Urszula Grzyb (416) 442-5600, ext. 3537 ugrzyb@annexbusinessmedia.com Peter Leonard (416) 510-6847 PLeonard@hpacmag.com Scott Jamieson

We acknowledge the financial support of the Government of Canada through the Canada Periodical Fund (CPF) for our publishing activities.

Proud member of:

MODERN HYDRONICS

FALL 2021

MH3

SWEET HEAT

SWEET HEAT AWARDS 2021 Celebrating the top residential and commercial entries in the first-ever Sweet Heat hydronics installation competition.

BY LOGAN CASWELL AND DOUG PICKLYK

L

aunched in late fall 2020, the first ever Canadian Sweet Heat Installation contest called on hydronic contractors from across the country to share photos of recent projects and explain the challenges and creative solutions their teams used to deliver comfort to their clients.

The installations could be in a new-build or a retrofit project, and it needed to be a Canadian contractor and a Canadianbased project. The community answered the call, and the competition received 31 entries from Victoria, B.C. to Bridgewater, Nova Scotia. The entries were divided into two categories (commercial and residential) and the final judging was performed by experts, John Seigenthaler and Robert Bean, who together bring 80 years of industry experience.

The winners and first runners-up in both categories were first revealed during the final session of the 2021 Modern Hydronics Summit, held online on March 30 and 31.

RIVERDALE PLUMBING First, our congratulations go to Riverdale Plumbing in Toronto for taking first place in the residential category for a modern custom home project located in the prestigious Forrest Hill area of Toronto.

Riverdale is a small family-owned company formed in 1974 and specializes in new build and retrofits, specifically in-floor heat, air handlers, hot water generation and snow melts.

The company's operations manager, Pierce Akins, explained some challenges the company faced with this award-winning project. “We had to redesign the hydronic system so it could physically fit based on the litmited space we were given to build our heating stations throughout the house,” said Akins.

“We used modulating pumps instead of fixed-speed pumps to save more energy and save space.”

Akins said he has seen an increased demand for hydronics in his business, especially in the high-end new builds in and around Toronto where the new designs present challenges to heat with traditional equipment.

On this project Akins explains how they changed the design from the original drawings of two large boilers to five smaller units. “It gave us the advantage of lower modulations while also meeting the higher loads once they all fire up together.

MH4

FALL 2021

Winner in the residential category, this custom home project was completed by Riverdale Plumbing in Toronto.

The Riverdale Plumbing project used modulating pumps instead of fixed-speed pumps to save energy and space.

MODERN HYDRONICS

WWW.HPACMAG.COM

Modern Hydronics

Winner of the commercial category; this is the mechanical room located in the basement of UBCO Nechako residence completed by Rambow Mechanical located in Kelowna, B.C.

Doing this we could get down to 40,000 Btus, which allowed us to save energy and use the boilers as effectively as possible.”

The boilers were installed to provide heat for two indirect hot water tanks, a large snow melt, indoor spa, outdoor spa, outdoor pool and supplementary heat (in-floor heat and heating coils) to the building. The primary heat for the building is provided by heat pumps.

Contest judge, Robert Bean, gave the Riverdale Plumbing project his vote for the top spot because the of its energy-saving efficiencies. “What I liked about this project was given the size of the loads, they used the least amount of electrical power to move the thermal energy through the building.”

Co-judge, John Seigenthaler concurred, adding that the untold story of hydronics is about judging the quality of a system by looking at both the energy consumed to produce the heat and the energy used to move it through the building.

Seigenthaler also admired the used of valves rather than zone circulators which use less electricity as well as the beautiful workmanship, well thought out design, modern technology and well-placed hardware from a servicing standpoint.

“From an energy standpoint, the use of a variable speed pressure-regulated circulator combined with valves is definitely going to use less energy,” said Seigenthaler. “A lot of preplanning went into this relatively small space in a very large home.”

The mechanical room is tied into a centralized campus lowtemperature district energy system (LDES).

500-seat dining hall, commercial kitchen and amenity spaces on bottom two floors.

Patrick Waunch, president and CEO of Rambow Mechanical, founded the business in 1985 with himself and an apprentice. Today, the firm specializes in industrial and commercial projects filling a niche throughout Western Canada with a regular team of around 45 people. “I enjoy a challenge,” says Waunch, who has over 50 years of experience in the commercial and industrial mechanical sector.

For this project, which lasted about two years, the building is tied into a centralized campus low-temperature district energy system (LDES). Heat pumps located in the Nechako building use water-to-water heat recovery for maximum efficiency when both heating and cooling are required. Two 8-in. stainless steel connections, which connect to two heat exchangers, provide an effective heat surface of 386 sq.m. per heat exchanger. This allows the system to both draw heat or reject heat back into the system.

The heat pumps send either hot or chilled water through a network of 6-way control valves that, in conjunction with a large number of thermostats, allow various fan coils, unit heaters and in-slab heating/cooling. The in-slab heating is located in the common restaurant area and unit heaters are located in main doorways and loading dock areas.

All of the pumps in the system have variable speed drives on them, ramping up and down driven by controls. In addition to the complex heating/cooling system, all the student room windows have a built-in contact sensor, monitored by a direct digital control (DDC) system, so when the window is opened the DDC is programmed to shut down the heating/cooling for energy savings. When the window is closed the DDC reactivates the fan coil in the room to its previous program.

“We had to redesign the hydronic system so it could fit.”

RAMBOW MECHANICAL The top entry in the commercial category was awarded to Rambow Mechanical of Kelowna, B.C. This new construction project, the Nechako residence, is part of the UBC Okanagan housing commons in Kelowna. The building itself is a 137,000 sq. ft. six-storey residence with some 220 bedrooms and a WWW.HPACMAG.COM

MODERN HYDRONICS

Continued on MH6 FALL 2021

MH5

SWEET HEAT

Modern Hydronics

2021 SWEET HEAT ENTRIES

Thank you to everyone who took the time to enter our first Sweet Heat Contest: Air Design Services, London, ON AV Mechanical, Caledon, ON Battye Mechanical, Peterborough, ON Boss Plumbing, Saskatoon, SK Canadian In-Floor Radiant Solutions, Burlington, ON Canuck Mechanical, Prince George, BC Deer Bridge Plumbing & Heating, Calgary, AB Denrite Mechanical, Sturgeon County, AB Doyle Plumbing Heating & Cooling, Fraserville, ON Gleeson Plumbing, Moorefield, ON Good Grade Plumbing & Gas, Victoria, BC Grand Mechanical Solutions, Brantford, ON GTAHeat.ca, Vaughan, ON JJM Mechanical Group, Burnaby, BC John Sadler Plumbing & Heating, Surrey, BC Lloyd HVAC Services, Toronto, ON Mason Place, Keswick, ON MICA Energy Solutions, Oshawa, ON Micon Plumbing, Mississauga, ON Northern Air & Mechanical Systems, Sudbury, ON Parr Mechanical Plumbing & Heating, St. Pauls, ON POC Plumbing & Heating, Oakville, ON Pre-Con Builders, Oakbluff, MB Pro Climate Mechanical, Concord, ON R4 Mechanical Systems, Wetaskiwin, AB Rambow Mechanical, Kelowna, BC RBA Mechanical, Edmonton, AB Rhynos, Bridgewater, NS Riverdale Plumbing, Toronto, ON TJL Mechanical, Fergus, ON TT Plumbing & Heating, King City, ON

Commercial installation runner-up, Grand Mechanical

Runner-up in the residential category, Denrite Mechanical

Another energy-saving element is the heat recovery system that captures heat from exhaust fans and the commercial kitchen range hood using an energy recovery ventilator (ERV) and repurposing that energy back into the HVAC system.

The heating system also aides the domestic hot water.

“Once our heating side returns back from the system it runs through a heat exchanger that tempers the incoming domestic cold water, so when you have low loads situations for heating you gain a lot of benefit from this second heat exchanger taking heat out of the heating system,” says Shayne Haller, project manager with Rambow Mechanical.

According to Wauch and Haller, working to the LEED Gold certification requirements on this project meant sourcing local materials that met the low environmental impact specifications (including cements, sealants, etc.). “A lot of paperwork and effort is required to satisfy the LEED certifications,” says Waunch, a process which is becoming a more common practice on all of their projects.

The Sweet Heat contest judges applauded the certification MH6

FALL 2021

requirements of the project. “I really liked the attention to the low temperatures in the heating, and that just makes the systems operate at their peak efficiency,” said Bean.

Siegenthaler added, “It really looked like they were taking advantage of opportunities to minimize energy use and use systems that work with good attention to the exergy concept.

As we move towards decarbonization, here’s a hydronic system that does a good job of recognizing that electrical-based systems and low-temperature systems are going to be the new normal in hydronics.”

“When we talk about the challenges we had, we also went through the Covid-19 scenario,” adds Waunch. “We had to maintain manpower, but we were very fortunate to be able to have people come in and out and have not one single case of Covid on-site.”

In all, the residence project lasted about a two-years for Rambow Mechanical, and it’s anticipated that the building will be full of students this fall.

MODERN HYDRONICS

Continued on MH8 WWW.HPACMAG.COM

DO MORE WITH LESS Cover 90% of your residential circulator needs with the ALPHA2 15-55 and ALPHA2 26-99.

ALPHA2 15-55 with line cord ALPHA2 15-55 with terminal box

ALPHA2 26-99 with terminal box

ALPHA2 – Delivers comfort and savings to your customers for years to come. Install our most efficient variable speed ECM circulator with patented AutoAdapt function.

CROSS REFERENCE CHART

ALPHA2 15-55

ALPHA2 26-99

Grundfos

TACO

Bell & Gossett

Armstrong

Wilo

UPS 15-58F/FR UPS-15-42F/FR UP15-10F UP15-42F

005 006 007 008 0010 0015 00R-IFC 00R-MSF1-1FC 007E 0015E 0018E

NRF-22 NRF-25 NRF9F/LW ECOCIRC 19-14 LR-20WR

ASTRO 30 ASTRO 50-3 ASTRO 25 ASTRO 30-0 ASTRO 20 ASTRO 230CI-R

STAR S 16FX STAR S 21FX STAR S 21RFC STRATOS ECO 16 RFC

0010 0011

NRF-36 SP#2 NRF-45 SP#2 SERIES 100 PL-30 PR NRF-36SP#1 NRF-45SP#1 LR-15BWR

E7(B) ASTRO 50(B) H41 ASTRO30(B) ASTRO 250CI-R

STAR 30 F STAR 32 F STAR 33 FC

UPS 26-99F

TO LEARN MORE, VISIT

grundfos.ca/HPACad2021

SWEET HEAT RUNNERS UP The runner-up spot in the residential category was awarded to Denrite Mechanical of Sturgeon County, Alberta. This home had a mechanical system which, according to Bean, “needed some therapy.”

Bean said he awarded the runner-up prize because of Denrite’s design and installation, particularly their attention to low-temp return temperatures.

“In order to get the maximum amount of work out of a boiler you need to get those temperatures down to 75-80F return water temperature. The only way to do this is to oversize the heat exchangers on the air handlers,” said Bean.

The project was also commended by Seigenthaler for its workmanship and design. “I gave a good rating for their ability to integrate that much hardware into the small space and yet keep accessibility for servicing,” said Seigenthaler.

FALL 2021 MH8 HPAC_ArcticHeat_Aug21.indd 1

Modern Hydronics

SWEET HEAT 2022

We are now inviting hydronics professionals across the country to get out your cameras and do it all over again.

Sweet Heat 2022 launches now, so if you take great pride in the work your team is doing and have new installation projects that are worth talking about (either new build or retrofits), it’s time to bring it on!

The entry process is simple, and you’ll find all the entry details at hpacmag.com/sweet-heat-2022 and maybe you’ll be our feature story next year.

Good luck to all.

Grand Mechanical Solutions of Brantford, Ontario was the runner-up in the commercial category. Their project was a new build facility for a landscape equipment supplier. The building included over 30,000 sq.ft. of radiant in-

MODERN HYDRONICS

floor heat and snow melt among the showroom, offices, service shop and underground garage. “I liked the application of multiple boilers staged, instead of putting one large device in,” says Bean. For Siegenthaler: “It was a good use of modern piping materials, and ECM circulators," and he appreciated how the controls were well separated from anywhere water could affect them.

Both judges were impressed with the quality of workmanship in all entries, but are always looking for how contractors use engineering principles which promote energy efficiency and compliance with standards. “When it comes to energy, conserve it first,” says Bean.

Their recommendations to future entrants is to demonstrate how you made your systems efficient, and where possible identify what standards you are meeting to provide comfort to your clients. <>

WWW.HPACMAG.COM

2021-08-04 3:47 PM

Some just see a blueprint.

You see a chance to grow your business.

Y

our business is all about cash flow, project performance and planning, going big too soon, having the best people, innovating and working with partners that really want to help you grow your business.

Your business needs innovative partnerships that incorporate the newest product technologies and digital tools — reliable

brands that make things better. That’s why AQUATECHTM is proud to offer Lochinvar® heating and hot water boiler solutions that perform for you and your customers.

Energy efficiency. Quality performance.

Broad product selection. And technical support.

Call us today and explore how our over 40 years of experience can support you.

Represented by

Aqua-Tech Sales and Marketing Inc. P: 905.631.5815 • F: 905.637.8655 • aquatech-canada.com

ZONING

Modern Hydronics

ZONING CONSIDERATIONS Things to consider when planning your piping layouts.

BY JOHN SIEGENTHALER

A

zone is any area of a building for which indoor air temperature is controlled by a single thermostat (or other type of temperature controller). A zone can be as small as a single room, or it may be as large as an entire building.

Multi-zone systems have the potential to provide two important benefits not available in single zone systems, namely: • The ability to meet individual comfort requirements through independent control of room temperature • And, the ability to conserve energy by reducing the temperature of unoccupied zones and thus the rate of heat loss from them.

Multi-zone hydronic systems are easy to create, much easier than their forcedair counterparts, and several hardware options exist for implementing zoning in different types of distribution systems.

However, before attempting to layout a zoned distribution system it’s important to evaluate how zoning can best be implemented in the building. The goal is to maximize the benefits of zoning while at the same time keeping the system affordable, energy efficient, reliable and as simple as possible.

AVOID OVERSELLING In some cases, hydronic zoning has been “oversold.” For example, potential clients, and even some heating professionals, sometimes think that the more zones a system has the better it is designed.

This is not true. Just because it is possible to create a separate zone for every room does not mean it is the best choice.

MH10

FALL 2021

In some cases, the extra piping and control hardware necessary for roomby-room zoning adds complexity and cost without returning tangible benefits.

Dividing a system into an excessive number of zones may even create operational problems such as heat source short-cycling. It can also add to system maintenance requirements, again without returning any benefit to the owner.

Here are several factors designers should consider when deciding how to best implement zoning.

THERMAL MASS Some people assume that zoned systems are somehow able to lower the temperature of a room (or group of rooms) down to some setback temperature as soon as the thermostat is turned down. Likewise, they might assume that any given room will quickly warm back to normal occupied temperatures as soon as the thermostat is turned up.

No occupied space can undergo a drop in temperature of several degrees over one to two minutes simply by stopping heat input. Similarly, no practical heating system can instantly raise the temperature of an occupied space by several degrees. The time required to cool down or warm up a zone is significantly affected by the thermal mass of the heat emitter(s), and the building itself.

The greater the thermal mass of the heating system and building components, the slower the decrease in indoor temperature when heat input to the zone stops. This is illustrated in Figure 1.

The two curves shown represent combinations of rooms and their associated heat emitter(s) with significantly different thermal masses. The room with low thermal mass could be a typical woodframed residential room with fin-tube MODERN HYDRONICS

Figure 1. Variables effecting heat loss

baseboard or perhaps a fan-coil as the heat emitter. The room with high thermal mass could be the same room, but equipped with a 4-in. thick heated floor slab as its heat emitter.

A very well insulated room (or an entire building) with high thermal mass might only experience a temperature drop of 3F to 5F over a cold midwinter nighttime lasting 8 to 10 hours, even with its heating system completely off.

If the occupants reduced the thermostat setting from 70F to 60F at night, the inside air temperature would not decrease to the reduced setpoint before morning. The energy savings potential of such a situation is very limited. If the thermostat were turned down 10F or even 20F, the results would be the same.

The thermal mass of the heat emitter also affects the recovery period when the setback ends. Low thermal mass heat emitters such as finned-tube convectors can usually restore a room that has been set back 10F to normal comfort in perhaps 15 to 30 minutes.

High thermal mass systems such as a heated concrete slab-on-grade floor can take several hours to bring a space back to normal comfort temperature following Continued on MH12 WWW.HPACMAG.COM

ZONING a prolonged setback period. This is illustrated in Figure 2, which shows the simulated heating of both medium-mass and high-mass radiant floor panels, starting at an initial temperature of 60F, and having a sustained heat input rate of 60,000 Btu/h.

It’s important not to use heat emitters having significantly different thermal mass in the same zone when that zone will operate with frequent changes in setpoint temperature. Because their response times during both cool down and warm up are so different, neither type of heat emitter is likely to produce acceptable comfort during the transition periods between stable setpoint temperatures.

It’s also important to realize that the energy conservation potential of a high thermal mass-zoned system is very dependent on the duration of any reduced thermostat setting.

If a zone can be maintained at a reduced temperature for several days, the energy conservation potential can be significant. However, attempting to create significant temperature changes on a daily basis in zones with high thermal mass heat emitters is futile.

The energy savings will be very small and the potential for temperature overshoot and undershoot will be significant.

This characteristic should be explained to eventual owners who may not understand how high-mass systems respond to changes in the thermostat settings.

HEAT FLOW TO ADJACENT ROOMS Another factor affecting zoning performance is inter-zone heat transfer. This refers to heat transfer through interior partitions as the building attempts to equalize temperature differences from one room to another.

If, for example, a particular room is kept at 65F, while an adjacent room is kept at 75F, heat will flow from the warmer to the cooler room through the wall separating them.

This partially defeats attempts to MH12

FALL 2021

Figure 2. Simulated heating of both medium-mass and high-mass radiant floor panels.

maintain temperature differences by zoning. The greater the thermal resistance of the exterior envelope of the building, the harder it is to maintain significant temperature differences between rooms separated by uninsulated interior partitions.

OCCUPANT INVOLVEMENT Another consideration that helps determine the cost effectiveness of zoning is the willingness of the occupants to regulate the system. It might seem obvious that an owner who is willing to pay more for an extensively zoned system would also be willing to regulate it. However, experience has proven that this is not always true, especially when nonprogrammable thermostats are used. Given modern lifestyles people often forget to regulate their heating systems.

Different rooms within a single zone (e.g., controlled by a single thermostat) and supplied with the same water temperature can still be maintained at different temperatures by adjusting the flow rate through individual heat emitters, assuming, that is, that these rooms are not all served by a series piping circuit. Flow balancing is usually adequate when the goal is to maintain several rooms at different (but stable) temperatures.

Room-by-room zoning is justified in situations where several rooms are to MODERN HYDRONICS

have both different and frequently changing air temperatures. It can also be justified when the added cost of room-by-room zoning is relatively small.

A good example of the latter is when panel radiators, each equipped with thermostatic valve actuators, and piped into either a homerun or “1-pipe” distribution system are used as heat emitters. These distinctions should be discussed with eventual owners before committing several hundred dollars for extensive zoning controls that may seldom be used.

INTERNAL HEAT GAINS Rooms with large south-facing windows may at times be totally heated by solar heat gains. Rooms in the same building that do not receive solar gain may still require heat input. Well-planned zoning separates rooms with likely solar heat gain from those without. It also accommodates the fact that the rooms receiving solar heat gain change over the course of the day as the sun moves.

Rooms that contain heat-producing equipment such as computers, copiers, vending machines, intense lighting or cooking facilities are usually good candidates for separate zoning.

It’s also important to use heat emitters with low thermal mass in areas subject to large and highly variable heat gain from the sun or other internal heat sources. The low-mass heat emitters can quickly start and stop heat input as necessary. This is especially important in modern buildings having very low rates of heat loss.

SLEEPING COMFORT Many people prefer to sleep in cool bedrooms. Good zoning design allows for this possibility. It’s common to zone a residential system so one or more bedrooms are controlled as a single zone.

Another common strategy is to create one zone for the master bedroom, with a separate zone for the master bathroom.

WWW.HPACMAG.COM

Modern Hydronics

This allows the bathroom to remain comfortable even when the bedroom is cool.

ACTIVITY LEVEL Exercise rooms are good candidates for separate zoning, while it’s unnecessary to maintain normal human thermal comfort conditions in spaces that are infrequently occupied—examples include basements, garages, guest rooms, and workshops. Garages, if heated, are usually maintained at air temperatures of 45F to perhaps 60F, and again are usually set up as a separate zone. In cold climates the garage zone is usually designed to operate with antifreeze. This allows the garage zone to be completely turned off, if desired, without the risk of freezing.

TRANSITORY AREAS Entry vestibules with exterior doors and

doors into fully heated space are good candidates for separate zoning.

In some cases, the goal is to maintain the vestibule at higher temperatures to help buffer interior spaces from cold air gusts when the exterior door is opened.

When floor heating is used in such high-traffic areas, the floor surface temperature is often maintained several degrees above that of other interior areas to help buffer the cold and to dry tracked-in moisture.

BLENDED SOLUTIONS These consideration should all be “weighed” when deciding upon a distribution system strategy. On some projects one or more of these considerations may not be present. On other projects some may be very dominant.

The “beauty” of modern hydronics technology is the ability to meld these considerations together in a way that enhances owner satisfaction while also providing energy efficiency and decades of reliable operation. <>

EXTERIOR EXPOSURE Rooms with minimal exterior exposure will have small heating loads relative to their floor area.

When such rooms are controlled as separate zones, overheating can be minimized. Rooms that have no surfaces exposed to the outside typically do not need heat emitters.

John Siegenthaler, P.E., is a licensed professional engineer. He has more than 40 years experience in designing modern hydronic heating systems. His latest book is Heating with Renewable Energy (see www.hydronicpros.com for more info).

MUNICIPAL

Hydronic Heat Pump Certification (MHHPC)

COURSE

For Hydronic Designers This is a must have to utilize the new TECA heatpump drawings and design projects involving air-to-water or water-to-water heat pumps.

For Hydronic Installers This is great insight into the proper sizing, operation and logic of heat pumps when utilized in a hydronic heating or cooling system

More Info

www.teca.ca Thermal Environmental Comfort Association 604.594.5956 / 1.888.577.3818 office@teca.ca

WWW.HPACMAG.COM

HPAC_TECA_August21_CSA.indd 1

MODERN HYDRONICS

FALL 2021 MH13 2021-07-28 7:24 AM

CHEMISTRY

Modern Hydronics

OPTIMIZING BOILER CHEMISTRY In this edition of 30 Mechanical Minutes panelists review why maintaining proper water chemistry is essential with modern boiler systems.

BY LOGAN CASWELL

I

n a recent installment of HPAC Magazine’s 30 Mechanical Minutes, the free webinar featuring virtual content for real world professionals, HPAC editor Doug Picklyk sat down with HPAC contributing writer Steve Goldie and Brian Morgan of The Morgan Group to discuss the merits of being proactive in dealing with water chemistry in the design, operation, and maintenance of hydronic systems. Goldie and Morgan shared their knowledge of treatment solutions and what’s important to consider in new and retrofit applications —both residential and commercial.

Although water is the optimal heat transfer medium, optimizing the water chemistry is vital in the new generation of modern boilers. Goldie, a hydronics specialist with Next Supply with more than 40-years-experience in the plumbing industry, recalled the main cause of corrosion and subsequent reduced reliability in old cast-iron boilers was oxidization due to air in the system.

The main culprit today is the quality of the water being pushed through the much narrower passageways. New technologies create hot water very quickly, and there are a lot of opportunities for scale build-up especially around the heat exchangers. This build-up can cause the heat exchanger to overheat MH14

FALL 2021

Webinar participants (top to bottom) Steve Goldie, Brian Morgan and Doug Picklyk, here discussing the important role of magnetic separators at keeping hydronic systems clean.

and fail which is a huge contrast to old cast iron systems which could be full of sediment for decades and still be functionally operational.

“Water chemistry is crucial these days,” said Goldie, “In my day, the most important component was the air separator. Now it’s not the case.” He went on to stress the importance of testing the pH of the water—even from the municipal supply—and to install a de-mineralizing cartridge which triggers an alarm to alert the owner when it needs to be replaced.

“Water quality and chemistry is something you can’t ignore anymore,” said Goldie. “It needs to be part of the regular maintenance schedule and routine of your boiler system.”

Boiler manufactures have now identified water chemistry as a catalyst for premature boiler system failures and have even made a point of nullifying their warranty if the boiler’s water supply is not maintained to their specifications.

Morgan illustrated the new best practices and recommendations issued by MODERN HYDRONICS

manufacturers which included procedures such as: • Test the water before you fill the system.

• Make sure you have air elimination in the system.

• Treat all boiler feed water as though it is hard water.

• Use chemical inhibitors on every job.

• Flush old and new systems with fresh clean water before commissioning the new boiler.

• Use magnetic dirt separators on systems containing large amounts of iron and to remove debris from system water.

• Where possible, treat boiler feed water.

• Repair system leaks immediately to prevent oxygen and untreated water from entering the system.

When installing a new boiler into a large building with existing steel and copper piping, sometimes it’s difficult to flush an entire system, Morgan recommends at the least testing the water and treating the system water before introducing new Continued on MH18 WWW.HPACMAG.COM

Trust Mitsubishi Electric For Your

Net Zero Hydronic Solutions LOW CARBON HYDRONIC HEATING & COOLING, AND DOMESTIC HOT WATER SYSTEMS u Natural Gas Alternatives for Electrification u Trusted Performance, Quality and Reliability u Reduces Energy Consumption Over Comparable Natural Gas Systems u Strong Canadian Customer Support Team

VISIT US AT CIPHEX WEST BOOTH 625

MITSUBISHIELECTRIC.CA | CLIMAVENETA.CA

Game changing innovation Introducing the smart generation of Vitodens Grow your business with Viessmann future-proof solutions. Our smart generation of high-efficiency gas condensing boilers and digital applications are designed to work for you, saving you time and energy on and off the job.

100 Series

100 Combi Series NEW 199 MBH 200 Series

+ Flexible installation with dual position display + Fast commissioning with preconfigured start-up guide + Easy remote monitoring and servicing with Vitoguide + Optimize maintenance with interchangeable spare parts and accessories + Fits any home with residential boiler sizes from 85 to 199 MBH, all with WiFi inside

smart heating solutions made easy

viessmann.ca

Wifi inside

Your all-in-one

Digital assistant Introducing Vitoguide

Our new Vitoguide app connects to any Vitodens smart generation boiler to streamline and simplify each installation. + All-in-one app for installation, service, maintenance & monitoring + Enhanced customer experience with annual automated maintenance reminders + Faster installation with guided step-by-step start-up and commissioning reporting + Simplified maintenance with replacement parts guide + Proactive monitoring with remote diagnostics & notifications

Download the Vitoguide app today

Register for new product training

CHEMISTRY

Modern Hydronics

boilers, or look at de-coupling the new boiler system from the existing system with a heat exchanger, so you can ensure you have great water quality flowing through the boilers.

He’s also seeing installations where the hydronic system is decoupled from the make-up water feed system with a make-up package to easily treat and test the water in the boiler system.

“I’ve seen closed-loop heating boilers installed in buildings where they’ve had leaks and in a very short order of time will fail because of scale build-up on the boiler,” agreed Goldie, who also pointed out the importance of the volume of water in a system even if the municipal water has been tested before entering the system.

“The problem is there might be so much volume in that building that there’s still enough mineral content in that volume of water…even though the water is within the acceptable limits,” said Goldie. “The total volume brings so much calcium into these heat exchangers that you’re still going to have a problem. I’m a big fan of isolating your boiler system from your building, so putting a heat exchanger in between your boiler and your system enables you to have much better control over the boiler water.”

Custom Built Retrofit Fan Coil Systems for Apartments & Condos Saving you and your customers time and unnecessary cost Installation of our high quality, custom-sized systems virtually eliminates all drywall, painting and finishing work while delivering, highly efficient, whisper quite comfort!

OUR PRODUCTS ARE: • Canadian made • Carry up to 5 year warranties • Available in both vertical and horizontal configurations

INNER-COOL SYSTEMS

FALL 2021

HPAC_Inner_Cool_Feb_2021.indd 1

This installation method is especially beneficial for instance when a service contractor may need to drain the riser. Without isolation the contractor is most likely to be refilling the system with untreated municipal water.

What about the use of glycol in hydronic systems? Morgan said the use of glycol can be beneficial for both its anti-freeze protection and its inhibitors which help prevent any microfilm build-up or rust in the piping system. The inhibitors also lubricate the seals and pumps which help the hydronics system overall.

Another crucial piece of equipment, in our experts’ opinions, is a magnetic filtration system. Magnetic filtration systems trap magnetite which is a build-up of metal particulates which attach to components in the heat exchangers and pumps. More and more manufacturers are recommending the installation of magnetic filters on inlets before the water goes into the heat exchanger or pump as a way of treating the magnetite problem.

“Magnetic filtration cannot be ignored anymore,” said Morgan who stressed it must be properly managed by the installer, and building owners need to be educated on the downfalls of noncompliance with the manufacturers’ recommendations.

“When someone spends $150,000 or more on a new commercial boiler system, and after one heating season it’s not covered under warranty and it’s failing … that’s a much bigger issue than what the investment would have been up front,” said Morgan.

The webinar ended after a brief question and answer session with the conclusion that optimizing boiler chemistry is not an option anymore, and it can save a lot of money if you maintain these systems according to the manufacturers’ recommendations no matter where your water comes from.

To view the full webinar visit hpacmag.com/tech-pulse. <>

HEAT TRANSFER PLATES

The next edition of 30 Mechanical Minutes will feature hydronics expert John Siegenthaler discussing the effect of heat transfer plates on the performance of “staple up” radiant floor heating systems.

Date: Thursday, September 2nd at 1PM (eastern time).

Visit hpacmag.com for registration details.

Contact us at 905-766-1513 and visit us online at inner-coolsystems.ca to check out our range of customizable options and our engineering excellence!

MH18

“Magnetic filtration cannot be ignored anymore.”

Sponsored by

MODERN HYDRONICS 2021-01-19 12:01 PM

WWW.HPACMAG.COM

24 x 32

SmartPlate Has EVolved Introducing SmartPlate EV. With its ultracompact 24" x 32" footprint, vertical piping connections and capacities up to 4500 MBH and 300 PSIG, the SmartPlate EV indirect water heater gives you greater design fl exibility for standard and highpressure systems. It also easily integrates with AERCO’s Benchmark boilers and smart Edge Controllers for a powerful combination system.

Join the EVolution. SmartPlate EV.

800.526.0288

I aerco.com ©2021 AERCO

DESIGN

WATER WORKS The design of the new headquarters for the Toronto and Region Conservation Authority will showcase its mechanical systems.

BY DOUG PICKLYK

M

MH20

FALL 2021

MODERN HYDRONICS

The new TRCA office is a mass timber building with geothermal heating and cooling and solar thermal panels.

cooling and ventilation opportunities.

For example, the building management system will alert occupants on their phone via an app to either open or close windows to ensure the building is using energy most efficiently.

The central mechanical room in the basement was originally planned as a closed-loop geothermal system, but after ground water was found on the site a redesign led to an open-loop geothermal solution. So instead of drilling some 44 boreholes, now there will be four boreholes. “The open-loop geothermal is an opportunity the client didn’t want to miss out on, because they are experts in water flow, conservation and protection their staff was able identify an underground bedrock valley in which underground aquifer sits” says Jamie Dabner, principal with Integral Group, the mechanical engineers on the project.

The original plan called for a solar thermal system on the roof as a back-up to the ground source heat pump strategy, but now with the geothermal system being configured with an open loop the geothermal system will connect to the mechanical plant in the basement and the solar thermal array on the roof will boost the efficiency of the system WWW.HPACMAG.COM

CREDIT: RENDERING COURTESY ZAS ARCHITECTS

anaging and protecting natural water systems in and around the city of Toronto is the mandate of the Toronto and Region Conservation Authority (TRCA), so it’s no surprise the design of the organization’s new headquarters incorporates water in many ways including, of course, its mechanical systems.

Being built near the Black Creek ravine in Toronto’s north end, the $65 million project (with support through NRCan’s GCWood Program) broke ground in January of 2020 with occupancy slated for September 2022. The new light-filled open-plan four-storey office building covers some 90,000 sq. ft. (8,100 m2) and will be a unique mass timber structure.

ZAS Architects of Toronto in a joint venture with Irish-based Bucholz McEvoy Architects designed the TRCA headquarters to be one of the most energy efficient mid-rise commercial buildings in North America “We envisioned TRCA’s new workplace as one that will inspire, motivate and support the culture of its employees, who are champions of the local environment,” says Peter Duckworth Pilkington, principal with ZAS Architects. In addition to the use of wood, other sustainable design features include an energy efficient building envelope, a green roof, rainwater harvesting, low impact landscape development, and solar chimneys which increase efficiency by heating ventilation air.

The heating and cooling system is

electric, using geothermal heat pumps along with roof mounted solar panels for thermal assistance. The project is participating in the Canadian Green Building Council’s (CaGBC) Zero Carbon Building Pilot Program, and it’s targeting Net Carbon Zero, LEED Platinum v4, Toronto Green Standard Level 2, and WELL Building Silver certifications.

“Overall, this building is tracking to be among the most energy efficient buildings in the country, somewhere around 54 ekWh/m² [equivalent kilowatt hours per meter-squared],” notes Duckworth Pilkington. When compared to traditional office buildings of this size, carbon emissions along with operating costs are projected to be reduced by up to 50%.

A main feature will be four water walls in the main atrium—each water wall is actually a glass enclosure (like a duct) in which the ventilation air is pulled down from the outdoor intake at the roof level and distributed to energy recovery ventilators (ERVs). Inside each of the glass ducts a chain-link mesh is suspended the full height and water cascades down the four-storeys—providing a visual display and playing a role in pre-heating and humidification of the dedicated outdoor air HVAC system. “Through the water wall feature, we’re making the building’s life support systems that are usually hidden infrastructure visible and tangible,” says Duckworth Pilkington. “Making the invisible visible when it comes to energy use, serves as a very real reminder of the impact our daily lives and decisions have on the planet every day.”

The windows on the southern façade feature operable exterior shading, and a secondary skin in front of the shading allows for pre-heating of the air before entering the building in cooler months.

A lot of the building’s control strategy is designed to optimize passive heating,

Modern Hydronics

and provide greater heating potential for the building. “We actually have it piped up to be available for free heating, so there are times in the shoulder seasons when we might not want to run the compressors, and we’re just going to

WWW.HPACMAG.COM

HPAC_MORGANGROUP_HALF_JULY_BAS.indd 1

run the building on solar thermal only,” explains Dabner.

Because the preference was to expose the wood on the interior and not hide it with drop ceilings, there is an air distribution plenum system, about 14-in. deep, across the top of each cross laminated timber (CLT) floor slab on every storey with supply air diffusers.

The plenum is used for ventilation only, and separate from that is the fourpipe radiant system with six-way valves feeding water-based ceiling panels used for both heating and cooling.

The piping network runs in the plenum, and the pipes poke down to the modular radiant ceiling panels which are hung on the underside of the CLT flooring.

“It’s quite a special strategy that required coordination with all of the design team,” says Dabner. The energy calculations led to about 40% of radiant

MODERN HYDRONICS

coverage in the interior zones of the building and the remaining 60% around the exterior zones of the building.

To accommodate cooling with the ceiling panels, considering Toronto’s summertime humidity, there will be dew point sensors in the thermostats in each of the zones, and if somebody opens a window raising the humidity indoors, the zone will turn off.

There are also ceiling fans, and according to Dabner the fans can increase the capacity of the radiant panels by up to about 10% in cooling mode.

He points out that a well thought-out four-pipe system is really the future of Net Zero carbon design.

Once completed, the new TRCA headquarters will be used as a learning centre–a living laboratory for developers, researchers and students–to demonstrate zero carbon features. <>

FALL 2021

MH21

2021-07-29 10:23 AM

IN-FLOOR

Modern Hydronics

IN-FLOOR PROVIDES RELIABLE STORAGE

B

elmont Farm Supply, located about 185 km outside of Toronto in Belmont, Ont, provides fertilizer, seed and more to farmers in the southwest region of the province. It has been part of the farming community since the 1940s.

When owner-partners Graham Hutton, Brad Walker and Jeff Aarts decided to build a new fertilizer warehouse, they wanted a state-of-the-art building to maintain the floor at a constant temperature. “We were trying to keep the moisture from forming on the concrete when the humidity rises,” Walker notes.

A floor temperature between 57F and 60F is essential when storing fertilizer. A lower floor temperature that allows outside temperatures to rise above it causes risk of condensation that can turn the fertilizer from a solid to a liquid.

Walker selected St. Marys, Ont.based iFH Design and Installations, headed up by Paul McRoberts, to design and install the radiant floor heating.

McRoberts is a 47-year veteran in hydronic heating; after beginning as an apprentice in 1972, he opened his own business in 1984 and was one of the first contractors in southwest Ontario to specialize in radiant floor heat.

DON’T FORGET THE INSULATION The ceiling height of the steel-constructed building is more than 36 ft. The MH22

FALL 2021

A 20,000 ft² fertilizer warehouse equipped with radiant floor heating.

concrete slab is 372 x 96 ft. More than four miles of PEX was installed. The radiant system uses piping in ¾-, 1-, 1-¼-, 1-½- and 2-in. sizes; 1 ¼-in. stainlesssteel manifolds; ¾-in. connectors; and compression-sleeve fittings.

“Instead of doing all the large diameter supply and return piping above, we did it all below ground with 2-in. and 1-½-in. oxygen-barrier piping with the fittings,” McRoberts explains. “Then we insulated all the piping with 1-in. foam insulation made for underground use.”

The next step was the placement of 2-in. expanded polystyrene panels that double as insulation and a piping-installation method. The ¾-in. by 500-ft loops were walked into place on top of the boards at 9-in to 12-in spacing then connected to the manifolds. A 40% glycol solution runs through the PEX network.

From the boiler room, all manifolds were supplied with 1-½-in. oxygen barrier supply lines. The longest supply lines were nearly 300 ft from the heat source.

“In each area of the manifolds, we installed floor sensor wells with PEX piping so we could insert our sensors in MODERN HYDRONICS

after the concrete was installed,” he says. “Before the concrete pour, the floor piping was pressurized to 100 psi to ensure there were no leaks under the floor, which also included the 1-½-in. and 2-in. in-slab distribution piping.”

In the mechanical room, two boilers are the heat source for the radiant heating system — providing nearly 800,000 Btu/h of energy to maintain the required floor temperature. Low-loss headers and a hydronic dirt separator provide hydraulic separation and protect the components.

A high capacity circulator distributes water to the five manifold stations. Isolation flange kits and floor sensing and pump controls round out the equipment.

QUALITY AND RELIABILITY Opened in April 2019, the owners have been through winter seasons with the warehouse full and have fine-tuned the floor temperatures. “We are extremely happy that we have the heated floor,” Walker says. “It certainly helps maintain the quality of our products.” <> This article provided courtesy of REHAU. WWW.HPACMAG.COM

PHOTO COURTESY OF IFH DESIGN AND INSTALLATION

Radiant heating used for temperature and condensation control in agricultural fertilizer warehouse.

Discover fresh ideas, expand your network, and fine-tune your skills at Western Canada’s biggest show for plumbing, hydronics and HVACR.

More than 30,000 sq ft of exhibits Thousands of products from North America’s top manufacturers Information packed seminars Fantastic prizes Free Parking for attendees

REGISTRATION OPENING SOON

EXPERIENCE THE FUTURE OF PLUMBING, HYDRONICS AND HVACR IN PERSON AT

CIPHEX WEST 2021 NEW DATE! November 3 & 4, 2021

New products. New ideas. New tools. New tech.

CIPHEX

WEST

Presented by the Canadian Institute of Plumbing & Heating

NEW LOCATION Pacific Coliseum at the PNE Vancouver, British Columbia

ciphexwest.ca

HEAT PUMPS

CUT IT OUT WITH THE CUT-OUT QUESTIONS Old ways of thinking are not compatible with a low carbon future.

BY CHRIS DESROCHES, P.ENG.

T

he term “heat pump” has many misnomers and gets thrown around far too loosely these days as HVAC conversations shift towards sustainability, low carbon emissions and building electrification.

A niche subset of heat pumps that are gaining momentum in the Canadian hydronics market are air-to-water heat pumps, which, aside from electric boilers, are an alternative to traditional fossil-fuel based boilers. Heat pumps sound attractive, so when it comes to hydronic systems, why are they still lurking in the shadows?

Air-to-water heat pumps extract heat from the air outside a building, so the machine’s ability to perform efficiently and provide useful heating is greatly influenced by outside air temperature. Any heat pump will have practical limitations due to the refrigerant being used, and it will eventually shut off when it can no longer effectively provide useful heat to the building. This is commonly referred to as the “low ambient cut-out temperature.”

And when it comes to designing with air-to-water heat pumps, the most critical design consideration the Canadian market is fixated on, and the first question to come up in heat pump conversations with a contractor or engineer is: “So… What about the cut-out temperature?”

While there have been great strides in improving heat pump performance and pushing the limits to operate in colder temperatures, usually, the design temMH24

FALL 2021

perature is below the heat pump cut out. In these cases, an auxiliary heat source will be required when using airto-water heat pumps. However it is important to recognize the frequency of time where it is colder than the cut-out temperature for the majority of Canada’s built environment is relatively few hours, typically a few weeks of the heating season. In favourable climates, such as coastal cities or even Toronto, it can be less than a week of the entire year.

When it comes to heat pumps, it’s about using the heat pump when it makes sense to do so.

“The days of seeking one size fits all solutions are finished.”

Gas-fired boilers have been the norm in Canadian hydronic systems for decades due to widely available low-cost natural gas, not to mention they are relatively inexpensive. Boilers do not have the same design challenges nor constraints that air-to-water heat pumps have, so it was easy for an engineer to explain to a client why they wouldn’t entertain an alternative to a boiler.

Today, design criteria are undergoing substantial change as the market shifts towards prioritizing energy efficiency and sustainability. Building and Energy Codes, as well as the metrics used to define what constitutes a “cutting-edge” and sustainable design are becoming more stringent. Limits on Energy Use MODERN HYDRONICS

Intensity (EUI), Thermal Energy Demand Intensity (TEDI), Greenhouse Gas Intensity (GHGI), among other metrics, are being scrutinized, and the bar is consistently being raised. While these metrics may be optional and modest today, they will become prerequisites as time moves forward to achieve net-zero in new buildings by 2030.

The Federal carbon tax will also transform the industry towards electric heating solutions, which brings us back to air-to-water heat pumps. By focussing on improving building designs with both active and passive energy reduction, we can improve our buildings’ carbon footprint, but will that be enough?

Air-to-water heat pumps are one part of a wider solution, and they will become more common on the path to 2030 in hydronic systems.

Do heat pumps have limitations? Yes, but there are workarounds. The days of one size fits all solutions are finished, as it is often not compatible with a low-carbon future. This should be viewed as a benefit by providing buildings with resiliency and redundancy.

It’s not so much a matter of if air-towater heat pumps will become the norm for hydronic systems, but rather when the market will recognize and understand how the technology fits into a low carbon building. So instead of asking “What is the cut-out temperature?” the real question is “What is the best way to make use of the heat pump while it can operate?” <>

By Chris DesRoches, P. Eng., Applied Product Manager, Mitsubishi Electric Sales Canada, Inc. WWW.HPACMAG.COM

August 2021

I SEE YOU’RE INTO HYDRONICS… IS CANADA’S #1 SOURCE FOR HYDRONIC COVERAGE: products, applications, events, news and more.

MODERN HYDRONICS 2021

MODERN HYDRONICS 2021

FALL

SPRING

MODERN HYDRONICS 2020 FALL

B.C. HIGH SCHOOL EMBRACES LOW-TEMP SYSTEM GEOTHERMAL CONTROL ISSUES

WAREHOUSE IN-FLOOR INSTALLATION SIZING PANEL RADS FOR LOW WATER TEMPS

SWEET HEAT 2021 This year’s contest-winning projects

FLOW ENERGY ...

DON'T WASTE IT Optimizing design for greater efficiency

PLANNING MULTI-ZONE LAYOUTS BOILER CHEMISTRY CONSIDERATIONS

COVID-19 AND HYDRONICS FLAME-FREE PIPING SOLUTIONS MODERN HYDRONICS SUMMIT PREVIEW

a publication of

10 EXPANSION TANK POINTERS OPTIMIZING EFFICIENCY WITH ECM CIRCULATORS

FOSSIL FUELS UNDER PRESSURE Navigating a ‘low carbon’ economy

DON’T MISS A Y COP SINGLE AC. OF HP

RENEWABLE HEAT SOURCE CONTROLS CONSTRUCTION CHANGES AFFECT DESIGN

a publication of

a publication of

FREE to qualified subscribers!

Please fill in the following and fax today to 416-442-2230 or visit our website and click on subscribe www.hpacmag.com

YES! I wish to receive/continue to receive HPAC Magazine absolutely FREE!

No

Name

1. Company Business Activity? (Check ONE only)

Title

 Mechanical Contractor  Fuel Oil Dealer/ Contractor  Consulting Engineers/Specifying Writer

 Refrigeration Service Engineer/Contractor  Wholesaler/Distributor/Agent  Plumbing Inspector

 Government  Utilities

 Hospitals and Related Institutions  General Building Construction

Company Address

 Others Allied to the Field (please specify) ————————————————————————————————

City

Province

Business Phone # ( Business Fax # (

Postal Code

2. Do you specify, purchase and/or approve the purchase of mechanical products or services?  Yes  No

)

3. Company Job Sector? (Check ALL that apply)  Commercial  Residential  Industrial  Institutional

)

Your FREE subscription also includes our FREE e-newsletter, please provide your e-mail address below: E-mail: Signature

Date (Must be signed and dated to be valid)

HPAC Magazine

111 Gordon Baker Rd. Suite 400, North York, ON M2H 3R1

Publisher reserves the right to determine qualification & limit distribution.

/ D

/ M

Y

4. Number of employees at this location? 1-4  20 - 49 5-9  50 - 99

 200 - 499  500 - 999

 10 - 19

 1000 - 2499

 100 - 199

5. Company Job Activities? (Check ALL that apply)  Plumbing (i.e DHW, Piping etc.)  Ventilation  Refrigeration  Electric Heating

 Forced Air Heating  Air Conditioning

 2500 +  Unknown

 Hydronic Heating  Fire Protection  Other—————————— (please specify)

FAX: 416-442-2230

PRODUCT SHOWCASE

Belimo has introduced its integrated Energy Valve and Thermal Energy Meter that together

Jaga Climate Systems has announced its new Dynamic Boost Hybrid (DBH) technology. Suit-

Webstone has announced their new Magnetic

provide energy measurement and control, Del-

ed for use with low-water temperature systems

Boiler Filter (MBF) XL model. MBF XL is de-

ta T management, and IoT-enabled billing. The

such as heat pumps, solar energy and con-

signed for larger residential boilers and is com-

solution offers direct integration to building

densing boilers, the new DBH unit connects to

monly installed on the system run. The magnet

management systems or IoT-based monitoring

a hydronic fin tube element, forcing convection

captures ferrous particles from the system be-

platforms. The valve and thermal energy meter

and increasing the efficiency of the emitter to

fore reaching the boiler, with an integral drain

can be powered using Power over Ethernet

provide quick heat. The unit gives users more

valve and service tool to remove the accumu-

(POE) allowing both power and network con-

control over individual room temperatures and

lated debris. The units are available with a

nectivity. They also connect with the Belimo As-

reduces the need for unnecessary heating and

choice of Press, FIP, MIP, or SWT union connec-

sistant apps and web server tool to support the

overheating.

tions to join to system piping.

design process, simplify commissioning, and

jaga-canada.com

www.webstonevalves.com

assist with troubleshooting. belimo.com

Viessmann has added WiFi connectivity to its latest generation of residential Vi-

Lochinvar has announced its new Crest con-

todens condensing boilers. The Vitodens

densing boilers with Hellcat combustion tech-

100, available in both combi (B1KE) and

nology for commercial applications. The com-

heat-only (B1HE) models, and Vitodens

mercial boilers come in eight models ranging

200 (B2HE) include stainless steel heat

from 1 million to 6 million Btu/h, with up to a

exchangers, the company’s Lambda Pro

25:1 turndown, a wave fire tube design, and

Plus clean combustion control, 10:1 turn-

CON-X-US Remote Connect capabilities. The

down ratio, and work with either propane

Hellcat technology features an O2 sensor lo-

or natural gas. Both are available in a

cated in the combustion chamber that along

range of sizes and MBH outputs. The new

with its Smart Touch controls helps adapt and

Vitoguide app allows contractors to com-

account for seasonal changes, shifts in weath-

mission the boilers from a mobile device.

er patterns and altitude. lochinvar.com

viessmann.ca

MH26

FALL 2021

Tekmar’s BACnet Snow/Ice Sensor Inter-

Navien’s NCB-H condensing combi-boiler se-

face 681 measures the presence of snow

ries includes five models ranging from

or ice through sensor technology and in-

160,000 Btu/h for DHW and 60,000 Btu/h for

terfaces with building automation sys-

heating, to 210,000 Btu/h DHW and 150,000

tems via BACnet MS/TP to automate the

Btu/h heating. The NCB-H uses dual stainless

start and stop and slab temperature op-

steel heat exchangers for heating and a sepa-

eration of hydronic or electric snow melt-

rate flat plate stainless steel heat exchanger

ing equipment. The interface supports

for DHW. Other features include: 15:1 turn

Snow/Ice Sensor 090 (automatic start

down ratio for DHW and up to 11:1 for heating,

and stop) and Snow Sensor 095. Fea-

built-in DHW recirculation controls, 2-in. vent-

tures include warm weather shut down

ing up to 65-ft. and 3-in. venting up to 150-ft.

and cold weather cut off. watts.com

navieninc.com MODERN HYDRONICS

WWW.HPACMAG.COM

Modern Hydronics

Bell & Gossett is expanding its CRS CoalescingStyle Air & Sediment Separator product line. The

Taco Comfort Solutions has expanded its offer-

The Bosch Singular Boiler series includes the

units help break entrained air and suspended

ing of stainless steel within its ECM circulator

5200 and 4000 combi boiler solutions, offer-

solids out of system fluid improving heat trans-

family. 00e Series circulators are built with ef-

ing 5.2 and 4 gallons of hot water per minute

fer and energy efficiency. CRS design helps pro-

ficient and quiet EC motors to consume up to

respectively.

tect pumps, boilers and other components, im-

85% less electricity, and also offer automatic

140,000 Btu/h for space heating, while the

proving and prolonging the life of a system.

unblocking and air-purge mode. Their dual

4000 unit offers 80,000 Btu/h. Featuring a

Models are available for air-only, sediment-only,

electronic knockouts and six-inch stranded

95% AFUE rating and a turndown ratio of up to

and air/sediment combo separation, and in

wire leads make for easy wiring. They also in-

10:1, the units include dual stainless-steel

sizes 2-in. through 36-in. with 2-in. – 4-in. flange

clude the integral flow check and are double-

heat exchangers and also feature an internal

or groove end connections.

insulated, so no ground wire is required.

circulator and the capability for outdoor reset.

bellgossett.com/sales-service

TacoComfort.com

www.boschheatingandcooling.com

The

Singular

5200

offers

Become a

Pro Dealer Reminders Referrals & Rewards Baxi Pro Dealers can start earning rewards today! Ask us how!

www.baxiboilers.com

Contact us for more information: (519) 627-0791 customerservice@mordennational.com

WWW.HPACMAG.COM

HPAC_ECR_March21.indd 1

MODERN HYDRONICS

FALL 2021 MH27 2021-02-11 11:57 AM

EMITTERS

ADJUSTING FOR CONDITIONS

How to size panel radiators for low water temperatures.

M

MH28

FALL 2021

SHOW ME THE NUMBERS As is the case with many heat emitters in North America, the published data for heat output from panel radiators is based on relatively high water temperatures. The most common being an average water temperature of 180F, and an assumed room air temperature of 68F. This makes the difference between the average water temperature in the radiator and the room air temperature 18068=112F. This temperature difference, or Delta T (∆T), is a reference condition which will eventually be used as part of the derating procedure for operation at lower water temperatures.

In North America it’s common to find heat output rating tables based on this 112F temperature difference. One example is shown in Figure 2 (pg. MH30).

MODERN HYDRONICS

The black numbers in Fig. 2 are heat outputs (in Btu/h) based on the dimensions (height, width, and thickness) of the radiator. The typical “thickness” dimension is based on 1, 2 or 3 water plates within the panel. Note the reference conditions in the upper right.

ADJUSTING DOWNWARD These rating tables are fine for installation where a conventional boiler operating at relatively high water temperatures serves as the heat source. But what happens when panel radiators are installed in lower water temperature systems supplied by heat pumps or other low temperature heat sources? The short answer is that their heat output decreases. But by how much?

To date, there is no North American WWW.HPACMAG.COM

CREDIT: PHOTO: MILEA/ISTOCK/GETTY

odern panel radiators are one of my favorite heat emitters. They’re easy to install, emit radiant as well as convective heat, and have high quality powder coat finishes. They’re nice in new construction and very well suited to retrofitting.

The panel in Figure 1 is about two feet high and four feet wide. You can see the two ½-in. PEX-AL-PEX tubes that supply it connected at the middle of the base of the radiator. You can also see the nonelectric thermostatic valve that regulates the flow rate and thus the heat output of the panel, making it an independent zone. There’s also a dual ball valve fixture at the base of the radiator that can isolate the panel from the system if ever necessary.

BY JOHN SIEGENTHALER

⎢⎝ ⎣

2

⎠

⎥ ⎦ Formula 3:

rating standard that’s specific to panel radiators. This is where we turn to a European standard called EN442. It is widely accepted across Europe where tens of millions of panel radiators are used, and it provides the basis for adjusting heat outputs over a wide range of conditions. It also involves several calculations.

Formula The 1: first of which is Formula 1: Formula 1:

⎛∆T ⎞ Qe = Q112 ⎜ d ⎟ ⎝ 112 ⎠

1.3

Where: Qe = estimated1: heat output of the panel Formula radiator (Btu/h) ∆Td = temperature difference deterFormula 2: Formula1.32 or Formula mined using either 3 below (F) ⎛ ∆ Td ⎞ Qe == Q ⎜⎝ of the⎟⎠ panel radiator Q112 the112 output 112between the averwhen the difference ⎡⎛ Tin + T ⎤ out ⎞ ∆ Twater − T ⎜ ⎟ d = temperature air age and room air tem⎢⎝ ⎥ ⎠ 2 ⎦ perature is ⎣112F (Btu/h) 1.3 = an exponent (not a multiplier) (use [yx] key on scientific calculator or your smart phone) 2: Formula

Formula 3:

Formula 2:

⎡⎛ T + T ⎞ ⎤ = ⎢(⎜Tin in− Toutout) ⎟ − Tair ⎥ ∆∆TT d d= ⎣⎛⎝ Tin −2Tair ⎞⎠ ⎦ ln ⎜ ⎝ Tout − Tair ⎟⎠ Formula 3:

∆T

∆ Td = d ⎛ T −T ⎞ ln ⎜ in air ⎟ ⎝ Tout − Tair ⎠

Formula 3:

Formula 3:

(Tin − Tout )

∆ Td =

⎛ T −T ⎞ ln ⎜ in air ⎟ ⎝ Tout − Tair ⎠

⎡⎛ T + T ⎞ ⎤ ⎡⎛ 160 + 140 ⎞ ⎤ ∆ Td = ⎢⎜ in out ⎟ − Tair ⎥ = ⎢⎜ ⎟⎠ − 65 ⎥ = 85º F ⎠ 2 2 ⎣⎝ ⎦ ⎣⎝ ⎦

Formula 4:

The value of Qn for Formula 1 is the radiator’s listed heat output at ∆T= 112, 1.3 1.3 which was Btu/h.

T ⎞ Btu ⎛ 85 ⎞ ⎛ ∆ 9500 Qe = Q112 ⎜ Td ⎟ =− 9500 = 6637 ⎜ ⎟ T ⎝air ⎠ ⎝ 112out ⎠ 112 Now u = just put the numbershr into Formula 1 and T grab − T your (scientific) cal-

( (

in

) air )

Formula 4:

u=

(Tout − Tair ) (Tin − Tair )

air

1.3

1.3

of a modern 85 Btu⎤panel radiator. ⎛⎡⎛Figure ⎞1. Example Tin⎛+∆TToutd ⎞⎞ = 9500 160 + 140 ⎡Q ⎤ ⎞ ⎛ Q = = 6637 ∆ Td e= ⎢⎜ 112 ⎜⎝ 112 ⎟⎠⎟ − Tair ⎥ = ⎜⎝⎢112 ⎜⎝ ⎟⎠ ⎟⎠ − 65 hr ⎥ = 85º F ⎝ ⎠ 2 2 ⎣ ⎦ ⎣ ⎦ WWW.HPACMAG.COM

⎛ Tin − Tair ⎞ ln culator. You can ⎜⎝ Tuse a−scientific ⎟⎠ calculaout to T air1.3 tor to raise a number the power.

Don’t have one? Just turn on your + T ⎞ the ⎤calculator ⎡⎛ T press ⎡⎛ 160 + 140APP, ⎤ iPhone, and ⎞ ∆ Td = ⎢⎜ in out ⎟ − Tair ⎥ = ⎢⎜ ⎟⎠ − 65 ⎥ = 85º F ⎠ to the 2 2 ⎣⎝ phone ⎦ “landscape” ⎣⎝ ⎦ turn the orientation - instant scientific calculator.

Here’s the result.

Where: ⎡⎛ T + Tout 1.3⎞ ⎤ ⎡⎛ 16 Btu = ⎜ ∆Qe T= Qd112=⎛⎜ ∆⎢T⎜d ⎞⎟ 1.3 =in9500 ⎛⎜ 85 ⎞ ⎟ − Tair ∆Td = effective temperature difference (F) = 6637 ⎥ ⎢⎝ ⎝ 112⎝⎠ hr ⎦ 2 ⎝ 112 ⎟⎠ ⎠ ⎣ ⎣ Tin = inlet water temperature to panel (F) Tout = outlet water temperature from As the entering water temperature Formula panel (F)1: drops closer to the room air temperaFormula 4: Tair = room air or the+flow Tin + Tout(F)⎞ 140rate ⎡1.3⎛temperature ⎤ ture, ⎡⎛ 160 ⎞ through⎤ the panel ∆==TQnatural = = 65 ⎥ = 85º − T ∆ T ⎛ ⎞ d ⎜ ⎟⎠ − standard ⎜ ⎟ lnQ logarithm function (use [ln] changes the EN442 intro-F d air ⎥ ⎢⎟⎠ ⎝ ⎢ (T − Tair2) e 112 ⎜ ⎠ ⎝ 112 ⎣ 2 u⎣=⎝ out ⎦ ⎦ key on scientific calculator or your smart duces way to calculate the (Tin −aTmodified air ) phone) difference between the average water Here’s an example: In Figure 2, a temperature in the panel and1.3 Formula 2: Td ⎞ the room ⎛ 85 ⎛ ∆the 2-water plate radiator that’s 24 inches air temperature value = ∆Td Qe = Q112(e.g., ⎜⎝ ⎜⎝ ⎟⎠ of 9500 Tout ⎞inches ⎡⎛ Tin +48 ⎤ 11 112 high and long has a rated used in Formula 1).

This is where ∆ Td = ⎢⎜ − Tair ⎥ ⎟ ⎠ 2 ⎣⎝ ⎦ heat output (at ∆T= 112 ºF) of 9,500 Formula 3 comes in.

Btu/h. Estimate its heat output assumThe decision on using Formula 3 Formula 3: 1.3 1.3 ing an inlet water temperature of 160F, rather Btu on yet ⎛ 85than ⎞ Formula 2 is based ⎛ ∆ Td ⎞ Q(Tine −=Twater Q112temperature 9500another 6637but it’s necesan outlet formula out ) ⎜⎝ ⎟⎠ = (sorry, ⎜⎝ ⎟⎠ of =140F, ∆ Td = ⎛ Tin − Tair ⎞ temperature 112 112 air and alnroom of 65F. sary).

We’ll call it Formula 4.hr Formula 4: ⎜⎝ T − T ⎟⎠ out air For now we will use Formula 2 to calculate the value of ∆Td: Formula 4:

(T − T ) ∆∆TTd == ⎡⎛ Tinin + Toutout⎞ − T ⎤ = ⎡⎛ 160 + 140 ⎞ − 65 ⎤ = 85º F ⎟⎠ ⎟⎠ ⎞ air ⎥ ⎢⎜⎝ d ⎢⎜⎝ ⎛ Tin2− Tair ⎥ 2 ⎣ ⎦ ⎣ ⎦ ln ⎜⎝ T − T ⎟⎠ out

Tout ) Hydronics (Tin −Modern

(T= in − Tout )

MODERN HYDRONICS

u=

(Tout − Tair ) (Tin − Tair )

Where: Tout = outlet fluid temperature from panel (F) Tin = inlet fluid temperature to panel (F) Tair = room air temperature (F) This formula looks at how the outlet temperature of the radiator is dropping relative to the inlet temperature. As the flow rate through the panel decreases there would be a wider temperature drop across the panel and thus the value of “u” in Formula 4 will drop.

Here’s the criteria set by the EN442 standard: If u < 0.7 use Formula 3 If u ≥ 0.7 use Formula 2 Here’s another example. Water enters the panel radiator used in the previous example at 115F, and exits at 92F. The Continued on MH30 FALL 2021

MH29

EMITTERS

Modern Hydronics

Since the EN442 standard (T − T ) 0.54 ( 92 − 65< ) =0.7 = 0.54 (T − T ) (115 − 65 ) prescribes use of Formula 3 to calculate ∆Td: u=

out

air

in

air

(Tin( − Tout) )

Heat output ratings (Btu/hr) at reference conditions: Average water temperature in panel = 180ºF Room temperature = 68ºF temperature drop across panel = 20ºF

1 water plate panel thickness

24" high

height

1 water plate

(T − Tair ) = ( 92 − 65 ) = 0.54 u = out (Tin − Tair ) (115 − 65 )

length

16" long

24" long

36" long

48" long

64" long

72" long

1607

2421

3632

4842

6455

7260

1870

20" high

2817

4222

5630

(T −TTair )−=Tair ( 92) − 65()92= −0.54 65 ) u = u =out ( out =− 65 ) = 0.54 (Tin −(TTair )− T(115 115 − 65 ) ( in air ) (T − T ) ( 92 − 65 ) = 0.54 u = (Tout − Tair )= ( 92 − 65 ) air in − Tair ) u = (Tout =(115 − 65 ) = 0.54 16" high

1352

2032

3046

4060

2 water plate panel thickness

24" high

2 water plates

air temperature in the room is 65F. Determine the correct ∆Td to use in Formula 1.

Solution: Start by calculating the value of u:

16" long

24" long

3153

4750

2733

16" high

10" high

(115 − 92 )

4123

2301

3455

1491

48" long

6186

8245

7127

(Tin − Tair ) (115 − 65 ) 20" high

36" long

9500

5180

2247

6907

3373

4498

7509 5415

64" long 12668 10994 9212 5995

8447 6091

72" long 14254 12368

10363 6745

23 23 = ∆T = = = T −T = 37.33º F ( 23 (115 − 92 ) = 23 = 50 ⎞ ln(1.85185) in out ) ⎛ 115 − 65 ⎞ ⎛ T −T ⎞ ⎛ = 3 water plate panel thickness ∆ T = = 37.33º F ln ⎜ ln ⎜ ⎟⎠ ln ⎜⎝ d ⎟⎠ ⎟ ⎝ 115 − 65 50 92 − 65 27 ln(1.85185) ⎛ Tin − Tair ⎞16" long ⎛ 24" long ⎞ 36" long ⎛ ⎞ 48" long ⎝ Tout − Tair ⎠ 64" long 72" long ln Tair ) need You’ll 115 − ⎜⎝92 (T −again ln ⎜ 24" highTin −⎟ T 23 ( 92 − 65scientific ) = 0.54 calculator ⎟⎠ ln ⎟⎠ 13664 23 18216 out ⎜115 6830 u = out = 4531 ⎝ 10247 20494 T − T − 92 ( ) 23 23 ( ) 92 65 27 T − T in out ⎝ ⎠ = ∆ T = = = = 37 T − T 115 − 65 out air ( ) ( ) d ∆ T 37.33 Btu ⎛ ⎞ ⎛ ⎞ in air = ∆ Td = = 9586 =11870 5015829= 37.33º F (or iPhone turned horizontally) to 20" high 3934 5937 17807 Q = Qyour ⎜⎝ ⎟ = 9500 ⎜⎝ ⎟ = 2277 115 − 65 ln(1.85185) ⎛ ⎞ ⎛ ⎞ ⎛ ⎞ − T T 112 ⎠ hr 112 ⎠ 115 − 65 50 ln(1.85185) ⎛ 4978 ⎞ 7469⎛ ⎞ 9957 ⎛ Tinhigh − Tairin ⎞3320air 14938 ln−⎜ 92 get the natural logarithm [ln] of 1.85185 ln ⎜⎟ 115 ln ⎜ ⎟⎟ 23 ln ⎜ 13277 ln ⎟⎠ 23 9913 ln ⎜ 16" ⎟⎠ 4958 T − T ⎜ ⎟ ⎝ ⎝ ⎠ ⎝ ⎠ ⎝ 2191 3304 6609 8811 10" high in out 92 − 65 27 92 − 65 27 Tout air ⎠− T= = = = 37.33º F in (Tthe above calculation. No big deal, ∆ Td = ⎝ Tout ⎝−T air ⎠ − T ) ( 90 − 70 ) 1.3 u= = = 0.441.3 115 − 65 50 ln(1.85185) ⎛ ⎞ ⎛ ⎞ ⎛ ⎞ − T T T − T ) (115 −∆ 70 )T ⎞ ( 37.33 Btu ⎛ ⎞ ⎛ d just on the calculator= 2277 ln ⎜ rating Figure tables for panel radiator Qe enter = Q112 ⎜1.85185 ln ⎜ in air ⎟ ln ⎜⎝ 2.1.3Sample⎟⎠heat output ⎟ ⎟⎠ = 9500 ⎜⎝ ⎝ 27 ⎟⎠ 92 − 65 T112 (90Tin) −⎝press 23 hr ) 11223⎠ display the(115 [ln−x]92key. ⎝ Tout −1.3Tair ⎠ out ) (115 −and (Tin − Tout )

115 − 92 23 23 ∆ Td = = = = = 37.33º F ⎛d T − T ⎞ ⎛ 115 − 65 ⎞ ⎛ 50 ⎞ ln(1.85185) ln ⎜ in air ⎟ ln ⎝⎜ ⎟ ln ⎜⎝ ⎠⎟ ⎠ 92 − 65 27 ⎝ Tout − Tair ⎠ in air

out

air

in

air

1.3

∆∆ TdT=d = = 30.83º F − 70 ⎛ 115 ⎛ T⎞ − Tair ⎞ ln ⎜ ⎝ 90 ln− 70 in⎟⎠

(

3 water plates

d

112

e

1.3

)

(

)

⎛ ∆FTd = 37.33º

(

)

(

)

⎛ 37.33 ⎞

⎞

Btu

Qe = Q112 radiators ⎛ 115 − 65value ⎞ ⎛ 50 ⎞ ln(1.85185) ⎜⎝ ⎟ = 9500 ⎜⎝ table⎟⎠ in = 2277 Now that the appropriate possible Nowhrit’s just a matter of looking ln ⎜ ln ⎜of ∆T 112 112 ⎠ from the ⎝ 92 − 65 ⎟⎠ ⎝ 27 ⎟⎠ d ⎝⎜ Tout − Tair ⎠⎟ 1.3 has been determined, the final step is to Figure 2. ∆ T 1.3 through the table in Figure 2 to find a raBtu ⎛ 37.33 ⎞ ⎛ d⎞ ⎛ 30.83 ⎞ 1.3 1.3 Q = Q = 9500 = 2277 2500 = Qthe plug numbers into Formula 1: Solution: Start with Formula 4: diator with output close to this ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ e 112 (⎝T112 ⎠− Tair ) = ( 90 − 70 ) = 0.44 ⎝ 112⎛⎠∆ Td ⎞ ⎝ 112 ⎠ ⎛ 37.33 ⎞ hr a listed Btu u = out value.⎟ A radiator with three water plates, Qe = Q112 ⎜ = 2277 (Tin − Tair1.3 ) (115 − 701.3) ⎟⎠ = 9500 ⎜⎝ 1.3 ⎠ of 24 in., and ⎝ 112 1.3 112 Btu ⎛ ∆ Td ⎞ ⎛ 37.33 ⎞ T − T 90 − 70 ( ) ( ) a height out air Q =Q = 9500 ⎜ ∆ T=d ⎞ 37.33 ⎞ Btu hr length of 48 in.

Btu ( 2500 ⎟⎠ = 2277 ⎛ ⎛ 112 ⎜) = 13,⎟ u = = 0.44 Q e= 374 ⎝ ⎠ ⎝ 112 hr 112 hr Qe =(TQin112− T⎜ air ) ⎟(115=−9500 ⎛ 30.83 ⎞ output of 13,664 Btu/h, which is ⎟ has=an2277 70 ) ⎜⎝ ⎝⎜ 112 ⎠⎟ ⎝ 112 ⎠ 112 ⎠ hr 115 − 90 ( ) very close to calculated output at This quarter of Tout − Tair ) ( 90 − 70 ) ( ∆ Td =is roughly about= one 30.83º F u= = = 0.44 − 70 ⎞ ⎛ 115 output the “rated” Since <T 0.7 use Formula Tair⎜heat 115 − 70 ) 3 to get ∆Td=112F. (T − ln ) 90 − 70 of the panel. I’ve ( (TinU(−115 air ) u = out ⎝ =90( − 70 ⎟⎠) = 0.44 − 90 ) − Tair )to be 70 ) “ballpark” ratio A radiator with three water plates found ∆T (115a−good (Tin25% 90 F− 70 d:d = Tout − Tair = 30.83º ∆T 115 − 70 u = = = 0.44 ⎛ ⎞ that’s 20 in. high and 64 in. long has a between the published heat output ratln ⎜− ⎟ T −− T90 Tout Tair 70 − 70 listed output of 15,829 Btu/h - more ⎝ in air)⎠ 90 −115 115 115 − 90 ( 90 70 ( ) ings of most panel radiators, based on 1.3 u∆=Td = = = 30.83º F= 0.44 ∆ Td = = 30.83º ⎛ 30.83 ⎞ F ⎛ 115 − 70 ⎞ 115 − 70 ⎞115 − 70 T − T than enough. the2500 ∆Tln 112F rating conditions, and ⎛ in air ⎟ 112 ⎜ ⎟ d=⎜⎝=Q 90 − 70 ln ⎜ ⎝ ⎠112 ⎠ ⎝ 90 − 70 ⎟⎠ Thanks for hanging in there through the estimated output when operating 1.3 115 − 90 the the panels in the1.3range of 105-110F av30.83 ⎞ ∆ =TdQ112 = ⎛⎜ = 30.83º F math. Think of these formulas like 2500 ⎛ 30.83 ⎞ ⎟ −115 90⎠ − 170with erage Next, set115 up 2500 =water Q112 ⎜ temperature. ⎝ 112 ⎛Formula ⎞ all the your tools. Used properly they get you to ⎝ 112 ⎟⎠ ∆ Td = information, 1.3 = 30.83º F ln ⎜ known including ⎛ 30.83 ⎞−⎞70 ⎟⎠ the re- the results you need. In this case they ⎛ 115 ( 2500 ) = 13, 374 Btu ⎝ −9070 2500 = Q ln Q = ⎜ ⎟ the 112 ⎜ ⎟ lower water give you accurate ways to select panel 112 quired heat output at WORKING BACKWARDS 1.3 ⎝ ⎝90112 hr − 70⎠ ⎠ ⎛ 30.83 ⎞ radiators that are compatible with low Now that2500 to reduce the temperature (e.g., 2,500 Btu/h): ⎟⎠ how Btu ( ⎜⎝you ) know 112 Q112 = = 13, 374 1.3panel temperature hydronic heat sources like heat output of radiators operating hr ( 2500 ) = 13, 374 Btu ⎛ 30.83 ⎞ ⎜⎝ ⎟⎠ 1.3 Q = 112 1.3 geothermal or air-to-water heat pumps. at lower 112 water temperatures let’s con⎛ 30.83 ⎞ ⎛ 30.83 1.3 ⎞ hr 2500 Q That’s a good skill to have as hydronics sider a typical sizing calculation where 30.83 ⎜⎝ (=2500 ⎟ ⎜ ⎟ ⎛ ⎞ 112 ⎠) ⎝ ⎠ Btu 2500 ⎟ 112 ⎜ 1.3 =112 Q112 == Q112 13, 374 technology evolves. <> you need to select a specific panel for a ⎝ ⎞112 ⎠ hr 30.83 ⎛ specific design load. ⎜⎝ ⎟ 112 ⎠ Consider a room with a design load of This can be solved for the necessary John Siegenthaler, P.E., is 2,500 Btu/h. The selected panel radia- output at the ∆Td=112F a licensed professional tor will be supplied with water at 115F, engineer. His latest book 2500 Btu 2500 Btu and operate with a 25F temperature is Heating with Renewable Q=112 = =374 13, 374 1.3 Q = 13, 112 1.3 drop. The room temperature will be 70F. Energy (hydronicpros.com ⎛ 30.83 hr hr ⎛ 30.83 ⎞ ⎞ Use the above information to select two for more information). ⎜ ⎜⎝ ⎟ ⎟⎠ =

=

=

1.3

112

112

1.3

( ( (

) ( ) )( ( )

(

) (

(

(

( ( )

)

) )

)

)

)

⎝ 112 112 ⎠

MH30

FALL 2021

MODERN HYDRONICS

WWW.HPACMAG.COM

www.caleffi.com

®

DIRTMAG PRO DIRT SEPARATOR WITH

40% MORE POWER

Caleffi pioneered the magnetic dirt separation market in North America over 10 years ago with DIRTMAG®.

Now say hello to DIRTMAG® PRO – our latest advancement in ferrous and non-ferrous debris separation.

Containing powerful, dual magnetic fields and a redesigned collision mesh, DIRTMAG PRO delivers 40% more power for greater efficiency in dirt removal. The debris blow-down valve makes serviceability simple, keeping your hands clean. CALEFFI GUARANTEED.

PEAK-PERFORMANCE HEATING SYSTEMS ComboMax ULTRA An electric boiler and instantaneous water heater: a combination without compromise.

VoltMax Increased temperature control.

Increased power control. The ideal electric boiler for your commercial projects.

BuffMax Optimize any type of hydronic system with the BuffMax buffer tank.

TurboMax The instantaneous indirect water heater with unmatched exchange capacity, exceptional hot water quality and a lifespan of more than 30 years.

Bth ULTRA and MINI The reliable and efficient electric boiler available in compact sizes for your residential needs.

MECHANICAL SUPPLY NEWS MANUFACTURERS • DISTRIBUTORS • WHOLESALERS

100 YEARS FOR COPELAND In celebration of the 100th anniversary of the Copeland brand, parent company Emerson will be marking the milestone all year long. Edmund Copeland founded the company in Detroit in 1921.

Emerson acquired Copeland in 1986 and recently completed an expansion of its Ohio engineering facility creating 110,000 sq. ft. of new R&D lab space. emerson.com/Copeland BECKETT ACQUIRES WESTWOOD The R.W. Beckett Corp. has acquired the assets of Westwood Products Inc., a supplier of specialty heating products for the oil heat and HVAC industries. beckettcorp.com

DISTRIBUTION >> Barclay Sales is now representing NTI Boilers in B.C., Alberta, Saskatchewan and Manitoba. barclaysales.com/ >> Jefcom Consultants Inc. is representing the Roth radiant and plumbing lines in Ontario. Sharp Environmental will continue to represent the Roth DWT in Ontario. jefcom.ca

New Dartmouth, Nova Scotia Distribution Centre with employees: Charlene Dort, Peter Lacoste and Bruce Paynter.

PHOTOS COURTESY IPEX

MARKS SUPPLY ACQUIRED BY MUNCH’S SUPPLY Munch’s Supply, a U.S.-based HVAC distributor celebrating its 65th year in business, made its first entry into the Canadian market with the acquisition of Marks Supply, an Ontario HVAC distributor with nine branches, three retail plumbing showrooms and two distribution centres.

“We have come a long way since my father started this business in 1962,” said Marks Supply president Robin Todd in a media release, adding, “Curtis Shea will step into the role of president and lead the Canadian operations for the combined company.”

Munch’s Supply is owned by North Carolina-based Ridgemont Equity Partners, a private equity firm. The addition of Marks Supply expands Munch’s geographic footprint to 51 locations serving 16 U.S. states and one Canadian province. munchsupply.com markssupply.ca

Winnipeg Distribution Centre employees: Trevor Kornago, Josh Chinchilla, Brendan Hapin, Hubert Akilimali, James Boisclair, Roger Habimana and Tim Sarchuk

IPEX OPENS TWO NEW CANADIAN DISTRIBUTION CENTRES Bringing more products closer to its customers and end-users, IPEX recently held grand opening ceremonies at two distribution centres (DCs), one in Winnipeg and the other in Dartmouth.

The new DCs are modern, larger buildings, replacing two smaller locations in both regions. The Winnipeg DC is a new build significantly increasing both warehousing and on-site yard space. The Dartmouth DC almost doubled in size and now provides yard space for more storage.

“Expanding our warehousing capabilities is integral to our customerfirst culture,” said Travis Lutes, president/COO, IPEX. ipexna.com

>> Air Heat Supplies is now a full-service stocking distributor of Baxi Boilers and accessories. The company operates three branches in the GTA (Mississauga, Scarborough and Toronto) and one in Belleville, Ont. airheat.ca OUELLET GROUP EXPANDS TO U.S./ LATIN AMERICA Ouellet Group Inc. has acquired Innovair Corp., a supplier of air conditioning and heat pump equipment in Latin America and the U.S. Ouellet Group also includes: Ouellet Canada in L’Islet; Dettson Industries in Sherbrooke (Que.); Hazloc Heaters in Calgary; Britech in Toronto; and Nanjing Ouellet—manufacturing plant in China. ouellet.com NAVIEN LAUNCHES CANADIAN FINANCING PROGRAM The new NaviLend Canada financing program is powered by SNAP Home Finance, and contractors who wish to take advantage of the program must be NavienRewards members and complete training with SNAP. Navien is offering a promotion for NaviLend applications submitted between July 15 to September 30, 2021 and funded by December 31, 2021. snap4home.com/navilend Continued on p50

HPACMAG.COM

AUGUST 2021 | HPAC

49

< MSN

Continued from p49

CIPH WELCOMES BILL HOOPER AS NEW CHAIR The Canadian Institute of Plumbing and Heating (CIPH) hosted its annual general meeting online, for the second year, with over 200 member-sites registered to attend. The 89th annual proceedings were led by interim-Chair Andrew Dyck, stepping in for Gail Kaufman who was unable to complete the term.

Meeting highlights included the naming of the 74th Chair, Bill Hooper, regional sales manager, Atlantic Canada, with Uponor. Upon accepting the new role, Hooper encouraged an ongoing culture of active volunteerism. “Let’s agree that there are no small roles in being a steward of the industry, and we can all find ways to lead and contribute.”

Five new members joined the CIPH Board this year including: Rita Woodley (Noble); Christine Joannou (Riobel); Barbara O’Reilly (Rheem Canada); Julie Storey (Boshart Industries); and David Succurro (Reliance Worldwide).

Presentation of the first ever Golden Leaf Award, given to a CIPH member (manufacturer/master distributor) who best supports sales agencies, was awarded to Bradford White Canada.

The Canadian Hydronics Council's Award of Merit went to Wade Peterson, vp sales/marketing with Heatlink Group.

Honorary Life Memberships: Rick Fantham (Emco), Kevin

Bill Hooper, CIPH Chair

Wade Peterson P.Eng., CHC Award of Merit recipient

Ralph Suppa, president CIPH (left), presents inaugural Gold Leaf Award to Mark Williamson, director of sales and marketing for Bradford White Canada.

Fullan (Master Group), John Hammill (Moen), Robert Whitty (Bartle & Gibson), Mike Patterson (Emco) and Paul McDonald (formerly, Bradford White). <>

TOGETHER, WE’ve PUMPED

A LOT OF WATER IN 80 YEARS

There’s a reason we’ve been the go-to pump for HVAC, Plumbing, Pool, and Hydroponics professionals for generations: experience.

For 80 years, Little Giant® products have stood the test of time, pumping a steady flow of proven reliability in the most demanding applications.

littlegiant.com

LG_Brand_Lift_Campaign_Print_Ads_Horizontal_DEV.indd 1

50

HPAC | AUGUST 2021

HPAC_Franklin_June21.indd 1

5/25/21 9:55 AM

HPACMAG.COM

2021-05-25 3:44 PM

PEOPLE > Aqua-Tech Sales and Marketing welcomes Paul McDonald as the national sales manager Monster Theisen focusing on wholesale McDonald distribution. McDonald brings years of experience from the manufacturing and distribution sides of the business. The company also welcomes Laura Monster and Ryan Theisen to the sales and marketing team. Monster joins the customer service representative (CSR) group and provide support for customers across Canada. Theisen will join the technical support representative (TSR) group with a focus on supporting manufacturers that Aqua-Tech represents..

Harry Kandilas has joined the Zurn Canada team as national sales manager. Kandilas brings over 25 years of industry-related sales and leadership experience, most recently he was general manKandilas ager of Vinylbilt Windows and Doors.

Weil-McLain Canada has introduced Lorenzo Rigatti as its new territory sales manager for Central Ontario. Rigatti will support hydronics contractors in the GTA and surrounding area with product selection, equipment installation, main- Rigatti tenance and troubleshooting.

Kristy Bell is the new national sales manager (Canada) for OS&B. Bell has over 13 years of experience in the Canadian plumbing and heating industry. In her new role, she will be responsible Bell for all Canadian plumbing wholesale sales of OS&B-branded products.

Ray Newstead has taken on the role of vice president of the Canadian division at ECCO Group Newstead Haine Bolger Sales and Distribution.

Newstead joins ECCO as a senior executive with several years of building products and HVAC industry experience, most recently as CEO. He will be responsible for the oversight of the company. ECCO Group has promoted Kevin Haine to division vice president of the U.S. division in sales and distribution.

Since joining ECCO in 2005 as a territory manager, most recently he was director of manufacturing sales. The company has also promoted Glen Bolger to vice president of operations. Bolger most recently held the position of director of manufacturing operations.

HPACMAG.COM

NAVAC announced Luis Ochoa as regional sales manager of the newly created eastern region. Ochoa will manage relationships with NAVAC’s Greaves distribution channels and oversee Ochoa the company’s representative network. The company has also promoted Andrew Greaves to director of education and customer experience, and he will oversee NAVAC’s tools and services education curriculum. He previously served as the company’s northern regional sales manager.

HRAI has hired Chelsea Goberdhan to its government relations team with a focus on the needs of members in Ontario, specifically contractors.

Goberdhan has worked as a legislative assistant and most recently as government relations coor- Goberdhan dinator for the Ontario Mining Association.

Blossom Pangowish has joined the Canadian Institute of Plumbing & Heating (CIPH) as a program manager. She is responsible for overseeing and supporting the activities of CIPH’s Annual Business Pangowish Conference set for June 19-21, 2022. <>

EASY. SAFE. FREE.

THERMOSTAT RECYCLING

We recycle all elements of the thermostat; plastic, metal, electronics and mercury (which is particularly hazardous).

Do your part and join the more than 1,500 contractors already participating in the program.

FOR MORE INFORMATION www.hrai.ca/trp 905-602-4710 trp@hrai.ca

Administered & delivered by: Supported by:

AUGUST 2021 | HPAC

51

< PLUMBING

LOOK FOR THE OPPORTUNITIES In a year of complications and unforeseen twists, where there’s a will there’s a way. BY STEVE GOLDIE

52

HPAC | AUGUST 2021

ILLUSTRATION: CORONA BOREALIS/ADOBE STOCK

I

was standing outside of my local pizza joint recently, waiting for my order, when I heard a voice call out my name from across the parking lot. I looked around and saw Tom, someone I first met over 40 years ago.

Back then I was not even an apprentice plumber; I was just working with my dad until I figured out what I really wanted to do. Most mornings my father and I would stop at the local plumbing wholesaler where Tom was working the counter; something to do till he went to university and figured out his future.

We were 18 or 19 years old, neither of us envisioned nor planned a career in the plumbing industry, and here we were still going with over 80 years of collective experience—Tom now a senior executive at the same company he started with, and I am just senior.

It was nice to catch up. He is still having fun and his passion and enthusiasm for the business was evident.

One of the things we spoke about was the unprecedented challenges the pandemic has created in our industry— specifically, material shortages and ever-lengthening lead times on virtually everything. We traded examples and remarked how we could never have imagined shortages on such everyday “bread and butter” type items.

I won’t mention specifics, but I am sure most if not all of you readers have experienced this first hand, and not just plumbing; these supply chain issues are creating challenges for pretty much every industry. Items that had lead times of two to four weeks in the past are routinely now eight to 12 weeks away.

In March a container cargo ship was stuck in Suez Canal, blocking the world’s busiest waterway.

Normally I would have been braced for a harsh response when delivering news of lead times this long, now most customers react with a knowing shrug. It’s not that they don’t care, it is simply an indication of how pervasive the problem is and how low expectations have become.

So how did we get here? Can we simply put all of the blame on Covid 19?

The short answer is, there is no short answer. We are all a part of a global economy that is intricately connected, and the supply chain that feeds it needs to operate with a complicated synchronicity.

If you remember back at the beginning of this global pandemic, many businesses were forced to close or slow production. This was the first jolt to hit the global supply chain knocking things out of sync. Granted, this was over a year ago, but the closures and slowdowns stretched to weeks and months with every jolt causing a ripple effect.

To make things worse, manufacturing of goods was not the only thing that was

affected, shipping also saw massive disruptions. When our global economy is in full swing, more than 5,000 ships can be floating on the oceans carrying upwards of 20 million shipping containers, filled with every type of consumer good.

The majority of these goods originate in Asia, with China home to seven of the 10 largest container ports worldwide.

The early days of the pandemic saw China virtually shut down for two months. Shutdowns in Europe and North America followed, but demand for household consumer goods actually increased as people were shut up at home. That coupled with a spike in demand for medical supplies that saw a significant surge in shipping once China opened up again. The sudden surge in shipping resulted in backlogs and congestion in the receiving ports in North America. This bottleneck in shipping is still responsible for many delays we are experiencing today, and I have not even mentioned the chaos that resulted Continued on p54 HPACMAG.COM

Quick Install Coupling Now with Innovative, new breakaway bolt design

Quality you can trust See just how quick installation can be • 4X faster than a traditional Coupling • Innovative one Bolt Design • Easy push on Design Innovative Design Features • 1-Bolt Design Saves installation time over conventional Couplings • Integrated Wedge ensures Gasket Compression and prevents pinching • New innovative breakaway bolt for seamless installation

Free Services Include: • • Cost Comparisons • Equipment Detail Packages

Quick Install Gasket • Pipe Stop: Ensures the Gasket is properly located in the connection, and assists in vertical installations • Gap Seal: The Gasket design is optimized for any sort of installation • Additionally, our Quick Install Gasket design ensures Gasket-to-Pipe contact from the moment you install it

Ready for Quick Installations • Hold Open Clip keeps the Coupling primed for Installers out of the box

www.Shurjoint.ApolloValves.com customer service (905) 761-6161

< PLUMBING

Continued from p52

when a massive container ship got stuck in the Suez Canal back in March.

If these Covid-related disruptions are not enough, we also saw a significant weather-related disruption when the freak winter storm hit Texas, a State not prepared for the deep freeze temperatures they were subjected to.

Much of the electrical grid went dark, which shut down gas production, which further hampered electrical production since natural gas is the main fuel source for electrical generation in Texas. Talk about ripple effects.

Texas is also home to many of the petro chemical plants responsible for much of the world’s plastic resin production. Theplasticsexchange.com estimated the Texas storm cost the plastics market 5 billion lbs. of resin. I have no idea how much of the total market that represents, but I’m sure if you take away

that much of raw material from any industry you are going to see shortages in finished goods somewhere. And since plastic resin is required to make plastic pipes and fittings it is easy to understand some of the shortages our industry is experiencing today.

So when will we see the end of this?

Well, I wish I could tell you to just be patient for a little while longer however things may get worse before they get better. It appears government stimulus spending, pent up consumer demand and increased vaccination rates are leading to a significant economic recovery.

Business is actually quite busy. Increased demand will place even more strain on an already stressed system. We will continue to see shortages and longer lead times for months, perhaps even longer.

I will conclude with an important thing to keep in mind: with challenges

come opportunities. My friend Tom seemed excited and energized by the challenges, and I agree. How we respond is up to us. Savvy contractors will look for alternative products, methods and suppliers to get things done.

Motivated suppliers will look for options as well, and will step into the service void to win new customers.

Now is not the time to be complacent, shrug our shoulders and accept the uphill battle of the “new normal” of long lead times. Now is the time roll up our sleeves, get to work and see what gold lies in them there hills. <> Steve Goldie spent 21 years in the field and joined the wholesale side of the plumbing business in 2002. He can be reached at sgoldie@nextsupply.ca.

CONDENSATE PUMPS NEUTRALIZER OPTION Residential and commercial condensate pumps with multiple inlets will discharge up to 15 Ft vertically.

Standard 3-year warranty. Comes with ready to install connections to an alarm system or shut-off switch.

Sanicondens® Best Flat *

Equipped with 20 feet of vinyl tubing, PVC discharge adapter and neutralizing granules*.

Low profile commercial model with built-in neutralizer can handle up to 500,000 BTU/hour*. * Based on commercial model

800-363-5874 54

HPAC | AUGUST 2021

HPAC_Saniflo_Aug21.indd 1

Sanicondens® saniflo.ca HPACMAG.COM

2021-08-04 12:01 PM

Power. Performance.

Endurance.

PVI’s Dynamic Water Heating® A revolutionary water heating system design and application approach that features greater BTU input for quick reaction, an optimized storage buffer for extra power when needed, the benefit of high water turnover, and exclusive duplex stainless steel AquaPLEX® construction for unmatched performance and longevity. Learn more about PVI’s Dynamic Water Heaters at pvi.com.

OptiSize® will help you select an optimally-sized water heater for your next project

800.784.8326 | pvi.com ©2021 PVI

PLUMBING PRODUCTS

The Teledyne Flir MR265 Moisture Meter and Thermal Imager is de-

Powers, a Watts brand, has added remote connectivity to its IntelliStation Jr.

signed to visually scan large areas to identify and locate moisture issues,

digital mixing valve. Now with WiFi capability, connecting to the Watts OnSite

air leaks and electrical problems. The dual thermal imager and measure-

mobile and web app for commercial facilities provides access to mixing

ment tool combines a 160 × 120 resolution thermal camera, visual cam-

valve data for building owners or contractors. BACnet and Modbus were al-

era, laser pointer, and both pin and pinless moisture detection for fast

ready native to the valves, but now Cloud connectivity provides an additional

leak identification and measurement. flir.com

way to view and adjust mixed outlet temperature. www.watts.com

PRIER’s P-6IV irrigation supply

Webstone has enhanced its E-X-P

valve for areas subject to freezing

Complete product line, now offering

comes with a built-in elbow that

everything needed for a gas-pow-

swivels to allow for easy installa-

ered tankless water heater (TWH)

tion. Designed with the contractor

installation. The new kits combine

in mind, it allows servicing from the

E2 series or Ultra-Compact series

exterior of the structure. A ¼-in.

TWH service valves with Webstone’s

NPT port in elbow allows for irriga-

forged brass gas sediment trap.

tion system winterization and air

Each ¾-in. kit includes two colour-

blowout. The heavy-pattern cast

coded service valves, a residential

brass hydrant with a nickel-plated

pressure relief valve, the sediment

body resists corrosion and offers a

trap kit with an FIP ball valve and a

triple-seal positive shutoff system.

24-in. gas flex line. Connection op-

The valve is available in 12 lengths.

tions include press, sweat, FIP, push

prier.com

and PEX. webstonevalves.com

The versatile RIDGID pipe saw is transportable and cuts 1-in. to 12-in. pipe with up to a ½-in. wall thickness. Configured to cut steel and stain-

The Symmons Rapid Install Bracket is a shower valve mounting bracket

less steel, with a switch to an optional blade it can cut plastic and cast

made of heat resistant nylon that creates a stable installation, particu-

steel. The saw secures to the pipe with a three-point roller system that

larly when using non-rigid supply lines, allowing installers to go back and

sets up and cuts up to 12-inch pipe. Well-placed handlebars and feed

service the valve without fear of damaging the lines. The bracket sets the

rate speed monitoring with an LED interface enable controlled rotation

rough-in depth and features over 1-in. of give for completing installation

from an ergonomic position. ridgid.com

with the surrounding tile/shower wall. symmons.com

56

HPAC | AUGUST 2021

HPACMAG.COM

August 2021

FREE to qualified subscribers!

Simply fax this form today or visit www.hpacmag.com and click subscribe!

STAY CONNECTED…

Please fill in the following and fax today to 416-442-2230 or visit our website and click on subscribe www.hpacmag.com

YES!

I wish to receive/continue to receive HPAC Magazine absolutely FREE! No

Name Title Company Address City

Province

Business Phone # (

)

Business Fax # (

Postal Code

)

Your FREE subscription also includes our FREE e-newsletter, please provide your e-mail address below: E-mail: Signature

Date

/

(Must be signed and dated to be valid)

D

/ M

Y

1. Company Business Activity? (Check ONE only)

o o o o o o

Mechanical Contractor Fuel Oil Dealer/ Contractor Consulting Engineers/Specifying Writer Government Utilities

o o o o o

Refrigeration Service Engineer/Contractor Wholesaler/Distributor/Agent Plumbing Inspector Hospitals and Related Institutions General Building Construction

Others Allied to the Field (please specify) –––––––––––––––––––––––––––––––––––––––––––

–––

2. Do you specify, purchase and/or approve the purchase of mechanical products or services?

o

Yes

o

No

3. Company Job Sector? (Check ALL that apply)

o

Commercial

o

Residential

o

Industrial

o

Institutional

4. Number of employees at this location?

o o o

1-4 5-9 10 - 19

o o o

20 - 49 50 - 99 100 - 199

o o o

o o

200 - 499 500 - 999

2500 + Unknown

1000 - 2499

5. Company Job Activities? (Check ALL that apply)

o o o

Plumbing (i.e DHW, Piping etc.)

Refrigeration Electric Heating

HPAC Magazine

o o o

Ventilation Forced Air Heating Air Conditioning

111 Gordon Baker Rd. Suite 400, North York, ON M2H 3R1

o o o

Hydronic Heating Fire Protection Other–––––––––––––––––– (please specify)

FAX: 416-442-2230

Publisher reserves the right to determine qualification & limit distribution.

< REFRIGERATION

UNDERSTANDING EVAPORATORS A fundamental element of the vapour compression cycle in refrigeration, it’s vital to revisit the basic functions of evaporators and how to keep them operating at their peak. BY DAVE DEMMA Evaporator [ ih-vap-uh-rey-ter ] An evaporator is a device in a process used to turn the liquid form of a chemical substance into its gaseous-form/ vapour. The liquid is evaporated, or vaporized, into a gas form of the targeted substance in that process.

58

HPAC | AUGUST 2021

PHOTO: ROBERT REASOR/ADOBE STOCK

T

he vapour compression cycle is a brilliantly designed machine which, when designed and applied properly, can maintain a designated space at a temperature that is lower than that of the immediate surroundings. It accomplishes this by transferring heat from the space to a heat transfer medium—in the case of the vapour compression cycle, that medium is a refrigerant.

The ultimate goal of the vapour compression cycle is to transform the refrigerant into a saturated fluid at a temperature that is low enough to facilitate the heat transfer necessary to achieve the desired temperature in the space.

There are four required components in the vapour compression cycle, each having its own specific function which contributes to that ultimate goal: Compressor: receives low pressure/ low temperature vapour from the evaporator and transforms it into high pressure vapour. Heat is added to the vapour during the compression process, and it leaves the compressor as a high pressure/high temperature vapour.

Condenser: receives high pressure/ high temperature vapour from the com-

Rusted and frozen evaporator coil resulting in compromised performance.

pressor and transfers heat from it. This allows it to change state from a vapour into a liquid. The liquid temperature is lower than the compressor discharge temperature, but still relatively warm.

Expansion Device: receives the high pressure/warm temperature liquid and forces it to undergo a pressure drop. Lowering the pressure allows the refrigerant to assume a new saturation temperature, which corresponds to the new lower pressure.

Evaporator: receives the low pressure/lower temperature saturated liquid from the expansion device, and it flows through the tubing in a finnedtube coil. The relatively warmer air in the space is circulated through the fins, allowing the heat from the air to be

transferred to the saturated refrigerant in the tubing, thus cooling the space.

While each component in the system is of equal importance, the evaporator is where the space temperature reduction takes place, and it is simply the result of heat transfer.

Evaporator capacity is based upon several factors: • Type of refrigerant • Refrigerated space temperature • Design condensing temperature • Amount of heat to be removed (heat load) • Humidity requirements for the space For example, if the design requirement is to keep beverages at 35F in a Continued on p60 HPACMAG.COM

When you want a faster, safer alternative to brazing...

Trust the technology that’s been proven more than 10 million times since 2015: RLS press fittings.

RLS Advantages:

While there will always be a need to braze, more and more HVAC/R contractors are also taking advantage of the time and cost savings – and proven reliability – of RLS press fittings. They connect in seconds, without the need for a torch, gas, nitrogen and everything else required for brazing (like hot work permits and fire spotters).

• UL Listed to 700 psi

With more than 10 million fittings installed successfully around the world since 2015, RLS technology has been proven beyond any doubt. Designed specifically for high-pressure HVAC/R systems, our patented double circular press results in two 360˚ metal-to-metal connections, creating a permanent mechanical joint every time, with no leak paths. So with RLS, you can connect with confidence!

• No burn permits

Learn more at rapidlockingsystem.com and become a certified installer at training.rapidlockingsystem.com.

• Connects in 10 seconds

• No gas or brazing materials • No flame, no fire hazards

• No fire spotters • No nitrogen purging • Works in tight spaces • Millions of fittings installed

Look for the flare!

That’s how you know it’s for HVAC/R.

rapidlockingsystem.com

< REFRIGERATION Continued from p58

refrigerated cabinet, then the system should be providing 25F saturated liquid refrigerant to the evaporator inlet. This will allow a 10F TD (temperature difference between air entering the evaporator fin-tube bundle and the saturated refrigerant flowing through the evaporator). This 10F difference allows the heat content in the higher temperature air to be transferred to the lower temperature refrigerant.

The amount of refrigerant necessary (mass flow rate) will depend on the type of refrigerant, the refrigeration load and the ambient condition. Of course, the design load is the maximum amount of heat transfer necessary to keep the product or space at the design temperature on the absolute most miserably hot and humid day in the summer time.

For the remainder of the year the equipment will be oversized. Yet, within a 24-hour period of any given day there will be continuous variations in the load (box doors being opened, product being loaded, changes in ambient temperature, etc.).

To compensate for the varying load condition a thermostatic expansion valve (or electric expansion valve) will modulate open/closed regulating refrigerant mass flow in response to the load at any given moment.

Factors that affect evaporator performance can be broken down into two categories, air flow and refrigerant mass flow.

AIR FLOW Evaporator capacity is, in part, based on the quantity of air flowing through the finned-tube bundle measured in cubic feet per minute (CFM). If any condition exists that would cause a reduction in the CFM, this will result in a reduction in evaporator capacity. For example: 1. Dust and dirt particles floating in the air are circulated through the exterior of the evaporator by the evaporator fans. These particles will accumulate on the evaporator fins and tubes. If evaporators are not cleaned periodically this buildup can seriously impede the air CFM, resulting in

Plugged filters will reduce air flow, which directly effects evaporator performance.

60

HPAC | AUGUST 2021

“Factors that affect evaporator performance can be broken down into two categories, air flow and refrigerant mass flow.” a loss of evaporator capacity.

2. Air conditioning systems will employ filters to reduce the amount of dust/dirt that can foul the evaporator surface.

Should these filters become restricted with a large buildup this will result in an air CFM reduction.

3. Return air ducting, if undersized, will result in an air CFM reduction.

4. If an evaporator fan has been replaced with a blade of the wrong pitch, this will result in an air CFM reduction.

5. If an evaporator fan motor has been replaced with a motor with a lower RPM than the original motor, or a multispeed motor incorrectly set up to operate at the wrong speed, this will result in an air CFM reduction.

6. Evaporators utilizing belt drive motors are always susceptible to worn/slipping belts, which will result in an air CFM reduction.

7. Evaporators with belt drive motors may utilize adjustable drive pulleys. If the pulleys are not adjusted correctly, this will result in an air CFM reduction.

REFRIGERANT MASS FLOW Evaporator capacity is also, in part, based on the refrigerant mass flow. At a given refrigerant saturation temperature there is a finite amount of heat that can be transferred to each lb. of refrigerant mass flow. As such, there will always be a specific requirement of refrigerant mass flow to meet the load demand at any given time. If any condition exists that would cause a reduction in the necessary refrigerant mass flow this too will result in a reduction in evaporator capacity.

1. Many reduced refrigerant mass flow issues can be directly traced to an underfeeding thermostatic expansion valve (TXV). This can be the result of an incorrectly sized expansion valve, a faulty valve adjustment, contaminant buildup inside the valve causing a restriction in flow, a defective thermostatic element (which reduces the valve opening force), incorrect thermostatic charge, or in some cases bulb charge migration (where the element head is colder than the element bulb, and the charge migrates to the colder area).

2. There is a certain percentage of liquid refrigerant that flashes into vapour during the expansion process and is HPACMAG.COM

Contaminate buildup in a thermostatic expansion valve can restrict refrigerant flow.

directly proportional to the difference between the entering liquid temperature and the saturation temperature in the evaporator. If abnormally high condensing temperatures occur (resulting from a dirty condenser), this can reduce the liquid refrigerant mass flow entering the evaporator after the expansion process.

3. Expansion valves can only operate at their rated capacity if they are being fed by 100% liquid refrigerant. To achieve this, the liquid entering the expansion valve must be slightly subcooled. Otherwise, the refrigerant will start to change state into a vapour. If there is excessive liquid pressure drop (undersized liquid line, restrictions in the filter-drier, solenoid valve, etc.), the liquid pressure can drop to a point where some portion of the liquid will “flash” into a vapour. This will result in the expansion valve being fed with a mixture of liquid and vapour, reducing the available liquid mass flow entering the evaporator.

4. Electric expansion valves are controlled by some type of electronic controller. There are certain parameters that must be entered for the controller to accurately control the valve. Among these are: (a) The total number of steps the valve travels from fully closed to fully open. For example, if the valve has a total of 2,500 steps, but the controller is set for 1,250 steps, the valve will never open more than 50% of its available stroke. (b) Each controller is programmed with several refrigerant options. For example, if the system is using R-404A, but the refrigerant parameter is set for R-22, the valve will not control accurately. (c) The superheat set-point must be entered for each application. If this is overlooked, or incorrectly set, it could result in the valve constantly underfeeding.

Understanding the function of the evaporator should assist the technician in garnering the maximum performance from it.

It should go without saying, in all systems great performance is directly proportional to precise set-up and commissioning. Maintaining that great performance is only possible with regular and thorough maintenance. <> Dave Demma holds a degree in refrigeration engineering and worked as a journeyman refrigeration technician before moving into the manufacturing sector where he regularly trains contractor and engineering groups. He can be reached at ddemma@uri.com.

THE SOURCE ADVERTISERS IN THIS ISSUE

Adrian Steel...................adriansteel.com/distributors.com........ P.9

Mitsubishi Electric.......mitsubishielectric.ca............................ P.31

AERCO............................aerco.com.............................................P.35

Morden/Baxi.................baxiboilers.com....................................P.43

Amvic..............................amvicsystem.com................................. P.27 AquaTech.......................aquatech-canada.com.........................P.25 Arctic Heat Pumps.......arcticheatpumps.com.......................... P.24

Navien.............................NavienInc.com...................................... P.18 Olimpia Splendid...........olimpiasplendidusa.com..................... P.13

Bradford White..............bradfordwhite.com...............................P.64

PVI..................................pvi.com.................................................P.55

Caleffi.............................caleffi.com............................................ P.47

RLS Fittings..................rapidlockingsystem.com......................P.59

CIPHEX West................ciphexwest.ca.......................................P.39

Saniflo............................saniflo.ca..............................................P.54

Conbraco........................apollovalves.com..................................P.53

TECA...............................teca.ca..................................................P.29

Ford.................................ford.ca/commercial-trucks................P.4, 5 Franklin Electric...........littlegiant.com......................................P.50 Grundfos.........................grundfos.ca/HPACad2021..................P.23

The Morgan Group........themorgangroup.ca............................. P.37 Thermo 2000................thermo2000.com.................................P.48

Inner-Cool Systems......inner-coolsystems.ca...........................P.34

Thermostat Recovery Program........hrai.ca/trp........................................... P. 51

Liberty Pumps...............LibertyPumps.com/NightEye..............P.63

TSI...................................tsi.com/AirAssure................................ P.15

LYNC...............................lyncbywatts.com..................................... P.2

Viessmann.....................viessmann.ca................................ P.32, 33

ICP – Keeprite...............keeprite.com......................................... P.16

HPACMAG.COM

AUGUST 2021 | HPAC

61

CALENDAR

FOR THE LATEST EVENT NEWS, SEE HPAC'S NEWSLETTER @ HPACMAG.COM

2021

Due to the COVID-19 pandemic visit event websites for the most current information.

NADCA Fall Technical Conference September 16-18 The National Air Duct Cleaners Association, an association for HVAC inspection, cleaning and restoration, is hosting its Fall Technical Conference in Charlotte, North Carolina.

HRAI Annual General Meeting September 23

BuildEX Vancouver/Alberta September 27-29

The Heating, Refrigeration and Air Conditioning Institute of Canada (HRAI) will be holding its annual general meeting virtually.

BuildEX Vancouver and Buildex Alberta will host in person micro events in Vancouver, Edmonton and Calgary along with online educational events. BUILDEX Amplified will come together for an in person event in February 2022 in Vancouver.

hrai.ca

nadca.com

CIPHEX West November 3-4 Western Canada’s plumbing, hydronics, heating, ventilation, air conditioning, refrigeration and water treatment show is being held at the Pacific National Exhibition Coliseum in Vancouver.

ciphexwest.ca

buildexvancouver.com

Building Performance Analysis Conference (ASHRAE) November 10-12 The conference will address the practices of energy modeling and building performance simulation using simulation tools, software development, and future research and applications.

The Buildings Show December 1-3 This annual show brings together renovators, contractors, designers and property managers to the Metro Toronto Convention Centre for a three-day trade show and conference.

thebuildingsshow.com

2022

ashrae.org/conferences

AHR Expo & ASHRAE Conference January 31-February 2 The Air Conditioning, Heating, Refrigeration (AHR) Expo returns in 2022 to the Convention Center in Las Vegas.

The annual showcase will reveal the future of HVAC/R technology along with plenty of educational and networking opportunities.

CMPX March 23-25 Held at the Metro Toronto Convention Centre, CMPX is one of North America’s largest trade shows for the mechanical and plumbing industries attracting some 500 exhibitors representing products, services, innovations and applications for industry professionals.

NCI High Performance HVAC Summit April 4–7 At the 2022 National Comfort Institute (NCI) Summit in Scottsdale, Arizona attendees can choose breakout sessions to attend based on three different knowledge levels: novice, practitioner, or mastery.

cmpxshow.com

gotosummit.com

MEET Show May 4-5

ASHRAE Annual Conference June 25-29

Canadian Hydronics Conference September 27-28

The second-largest industry event of its type in Canada, and the largest trade event east of Montreal, MEET features some 400 companies in over 100,000+ sq. ft. of exhibit space in the Moncton Coliseum Complex.

The annual conference is being held in Toronto at the Sheraton City Centre. In addition, the 13th International Industrial Ventilation Conference for Contaminant Control is taking place June 22-24 in the same place.

The conference will bring hydronics industry professionals together in Saskatoon to connect in person and share knowledge and business building ideas.

meetshow.ca

ashrae.org/conferences

ahrexpo.com

ciph.com/page/chc2021

Planning an event?

Send the details to dpicklyk@hpacmag.com 62

HPAC | AUGUST 2021

HPACMAG.COM

® Wireless Enabled Products

A LWA Y S WA TC H I N G .

Know what's happening with your pump - anywhere in the world, with NightEye® wireless connected products by Liberty Pumps.

SAFETY AND PEACE OF MIND WHILE AWAY FROM HOME. • Free app download • Cloud-based system designed exclusively by Liberty Pumps • No service or subscription fees • Works through your home's wireless router • Connect using simple BlinkUp™ technology - no PC required • Available on pump alarms and emergency back-up pumps • Apple® iOS and Android® compatible • One NightEye® app can support multiple devices/installations (Separate control/alarm unit required for each installation) • User-defined low basement temperature alert

® logo on pump Just look for the alarms, back-up pumps and other new products from Liberty Pumps

LibertyPumps.com/NightEye 8 0 0 . 5 4 3 . 2 5 5 0 Copyright © Liberty Pumps, Inc. 2021 All rights reserved.

THE ULTIMATE TANKLESS SOLUTION The Infiniti® K Series delivers exceptional performance and outstanding efficiency for endless hot water delivery. The Infiniti ® K Series features: • EASY INSTALLATION. Built For The Pro® for easier installation and maintenance. Includes built-in flush valves and bigger, roomier box.

• STEADISET® TECHNOLOGY to keep the water temperature accurate and consistent for an endless supply of perfectly-hot water.

• VENTING FLEXIBILITY. Can vent with 2” or 3” PVC or polypropylene up to a max length of 280ft.

• OUTSTANDING ENERGY EFFICIENCY. The Infiniti® K Series is ENERGY STAR® certified to save your customers money all year long.

• SRT™ SCALE REDUCTION TECHNOLOGY for improved performance, longer life and easier maintenance.

Are you ready to try a tankless?

Visit bradfordwhite.com/infinitiseries

©2021, Bradford White Corporation. All rights reserved. BWHPAC0821