Salomon Tech Manual Alpine 2020/21 by Salomon

TECHNICAL MANUAL ALPINE 2020/21

SALOMON WARRANTY POLICY.. . . . . . . . . . . . . . . . . . .

TECHNICAL MANUAL ALPINE 2020/21

SKI Ski length guide adult. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Ski length guide junior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 "G" Norms specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Maintenance repairs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Ski touring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

BINDING Liability indemnification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14 15 16

MOUNTING BINDINGS, SELECTING THE JIG. . . . . . . . . . . . . . . . . . 16 USING THE JIG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 DRILLING, TAPPING, GLUE, MOUNTING. . . . . . . . . . . . . . . . . . . . . . . 18

General mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Binding brake models braking capacity.. . . . . . . . . . Adjusting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FORWARD PRESSURE ADJUSTMENT. . . . . . . . . . . . . . . . . . . . . . . . . . .

TECHNICAL MANUAL ALPINE 2020/21

Boots & binding compatibilities. . . . . . . . . . . . . . . . . . . . . Special cases in mounting & adjusting. . . . . . . . . . . .

WARDEN MNC 11 DEMO BINDING. . . . . . . . . . . . . . . . . . . . . . . . . WARDEN MNC 11 BINDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WARDEN MNC 13 DEMO BINDING. . . . . . . . . . . . . . . . . . . . . . . . . WARDEN MNC 13 BINDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GUARDIAN MNC BINDING - Backcountry.. . . . . . . . . . . . . . . . . . . . . S LAB SHIFT MNC 10 & 13 BINDING. . . . . . . . . . . . . . . . . . . . . . . . .

72 74 76 78 80 84

STH2 BINDING "WTR" TECHNOLOGY. . . . . . . . . . . . . . . . . . . . . . . . 88

MTN PURE & MTN TOUR BINDING. . . . . . . . . . . . . . . . . . . . . . . . . . . 91

21 22

Release value selection and adjustment. . . . . . . . . . . 95 Final checking and visual inspection. . . . . . . . . . . . . . . 98 Mechanical inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Retail - specific instructions. . . . . . . . . . . . . . . . . . . . . . . . . 101 Rental - specific instructions. . . . . . . . . . . . . . . . . . . . . . . . 102 Maintenance and repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Traceability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

24 27

SYNCHRO CENTER AND SYNCHRO RENTAL BINDING. . . . . . . . . SMARTRAK BINDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SMARTRAK GRIP / GRIP PLUS BINDING.. . . . . . . . . . . . . . . . . . . . . . . LIGHTRAK PLATE J L & H L BINDING. . . . . . . . . . . . . . . . . . . . . . . . . . . X12 TL & X14 TL BINDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X12 & X16 BINDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . JUNIOR RACE PLATE/JUNIOR RACE PEDAL KIT BINDING. . . . . . . . . X TRACK PLATE WITH XT BINDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEED PLATE + Z BINDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EASYTRAK PLATE WITH L&C BINDING. . . . . . . . . . . . . . . . . . . . . . . . . EASYTRAK PLATE WITH LITHIUM BINDING.. . . . . . . . . . . . . . . . . . . . . EASYTRAK PLATE WITH MERCURY BINDING. . . . . . . . . . . . . . . . . . . . WARDEN 11 BINDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WARDEN 11 DEMO BINDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28 30 31 32 33 34 35 37 39 41 43 46 48 50

N C5 GW 2BINDINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N L7 GW BINDINGS.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . JUNIORTRAK PLATE WITH C5 GW BINDING. . . . . . . . . . . . . . . . . . . JUNIORTRAK PLATE WITH L6 GW BINDING. . . . . . . . . . . . . . . . . . . . EASYTRAK PLATE WITH L10 GW BINDING. . . . . . . . . . . . . . . . . . . . . EASYTRAK PLATE WITH Z11 GW & Z10 GW BINDING. . . . . . . . . LEISURE TRAK PLATE WITH M10 GW & M11 GW BINDINGS. . . . FLEXTRAK PLATE WITH Z12 GW BINDING. . . . . . . . . . . . . . . . . . . . . X12 TL GW & X14 TL GW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

53 55 57 59 61 63 65 67 69

BOOT Norm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sizing table information . . . . . . . . . . . . . . . . . . . . . . . . . . . Custom Shell procedure & FAQ . . . . . . . . . . . . . . . . . . Custom Fit procedure .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to mesure a foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Boot feature / Customization . . . . . . . . . . . . . . . . . . . . . Replacement procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Foot anatomy and fit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HELMET

.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

110 110 113 116 117 118 124 126 132

GOGGLE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

138

POLE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

148

BACK PROTECTION

2 summary <<<

.. . . . . . . . . . . . . . . . . . . . . . . . . .

150

S ALO MON L I M I T E D WA RR A NT Y P O L I C Y

You will find below all SALOMON warranty policy details offered by SALOMON and SALOMON authorized retailers. This warranty policy is valid as of December 2nd 2015.

I. LIMITED WARRANTY SALOMON provides this warranty to consumers who purchased SALOMON product (Product(s)) from SALOMON or one of it authorized retailers. SALOMON warrants all new Products to be free from manufacturing or material defects (Defects) for the Warranty Period as defined below. This warranty applies only against Defects discovered within the Warranty Period and extends only to the original purchaser of the Product. SALOMON Products meet their description and specifications; it is your responsibility to ensure that the Products you purchase are designed for your intended use. This warranty is valid and enforceable only in the country where the Product was purchased by the original purchaser, provided that SALOMON has intended that the Product be offered for sale in that country. This warranty is also enforceable in any country within European Economic Area where SALOMON has an authorized importer, subsidiary or distributor. Please refer to the SALOMON authorized retailers list. Depending on the country, particular and variable warranties may apply in relation to applicable legislation. Nothing in this warranty policy can exclude or limit these statutory provisions. WARRANTY PERIOD The Warranty Period starts on the date of the retail purchase of the Product by the original purchaser. The Product may consist of several different parts and different parts may be covered by different Warranty Periods (please

III. WARRANTY ENFORCEMENT

The Warranty Periods are: a. Five (5) years for alpine ski bindings originally purchased prior to October 1, 2011 b. Three (3) years for winter sports trousers and jackets c. Two (2) years for all other Products

SALOMON or its authorized retailer shall at its sole discretion either (a) repair the Product or (b) replace the Product at no charge. The appropriate remedy will be determined by SALOMON based upon the following considerations: (a) the value of the Product with no Defect, (b) the significance of the Defect, and the inconvenience each remedy would place on the original purchaser. SALOMON agrees that all repair or replacement of the Product will occur within a reasonable period

To the extent permitted by national laws, the Warranty Period will not be extended, renewed or otherwise affected due to subsequent resale, repair or replacement of the Product. However, part(s) repaired or replacement Product(s) issued during the Warranty Period will be warranted for the reminder of the original Warranty Period only; provided, such replacement or repair has been performed by SALOMON or an authorized SALOMON retailer. Depending on the country, particular and variable Warranties Periods may apply in relation to applicable legislation. Nothing in this warranty policy can exclude or limit such legislation.

II. CONDITIONS AND RESTRICTIONS This Limited warranty: does not cover: a. Normal wear and tear of the Product b. Defects caused by the Transportation or storage of the Product c. Defects or damage caused by improper use or poor maintenance d. Damages due to non observance of the instructions of the products owner manual e. Damages due to the modifications of the Product f. Any impact caused by sharp or hard items or objects, due to torsion, compression, a fall, an abnormal impact or other actions not under SALOMONâ&#x20AC;&#x2122;s reasonable control. This limited warranty is not enforceable if: a. The Product has been modified or repaired by any person or entity other than SALOMON or an authorized SALOMON retailer; b. The Product has been repaired with unauthorized spare parts c. The Product serial number has been removed, deleted, altered or made illegible.

For all warranty claims, please submit the Product and the proof of purchase to the nearest authorized SALOMON retailer or in the event you purchased the Product on SALOMON Online Store, please contact Customer Service. For all warranty claims, please refer to the FAQ/ RETURN POLICY available on www.salomon.com

IV. DISCLAIMER AND LIMITATION OF LIABILITY TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE MANDATORY LAWS, THIS LIMITED WARRANTY IS YOUR SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED. SALOMON SHALL NOT BE LIABLE FOR SPECIAL, INCIDENTIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LOSS OF ANTICIPATED BENEFITS, LOSS OF USE, LOSS OF REVENUE, COST OF ANY STUBSTITUTE EQUIPMENT OR FACILITIES, CLAIMS OF THIRD PARTIES, DAMAGE TO PROPERTY RESULTING FROM THE PURCHASE OR USE OF THE PRODUCT OR ARISING FROM THE BREACH OF THE WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT TORT, OR ANY LEGAL OR EQUITABLE THEORY, EVEN IF SALOMON KNEW OF THE LIKELIHOOD OF SUCH DAMAGES. SALOMON SHALL NOT BE LIABLE FOR DELAY IN RENDERING WARRANTY SERVICE.

TECHNICAL MANUAL ALPINE 2020/21

SALOMON distributes its products through its worldwide network of authorized SALOMON distributors and retailers and on the SALOMON Online Store at the URLs: www.salomon.com www.salomonrunning.com www.salomonfreeski.com (SALOMON Online Store)

refer to the Warranty Periods below for all warranties that may apply to your Product).

WARRANTY

Thank you for buying this SALOMON product.

3 summary <<<

NOTES

summary <<<

SKI

TECHNICAL MANUAL ALPINE 2020/21

SKI

summary <<<

SKI LENGTH GUIDE – ADULT

ADULT

SKIER WEIGHT (kg)

< 47

48-52

53-58

59-65

66-73

74-82

> 83

SKI LENGTHS (cm) (1)

145

150

155

160

165

170

175

+ LEVEL (2) BEGINNER

INTERMEDIATE

ADVANCED

EXPERT

First time skier Flat terrain to green slopes (EU) / green circle (Noram)

From snowplough turn to parallel Drift at the end of turn No off piste Green slopes to blue slopes (EU) / Blue square (Noram)

Parallel turns Drift, carve on easy slopes OK in mixed snow Confidence on most slopes Red pist (EU)/Black diamond (Noram)

Parallel short and long (radius) turns Carving skills All terrain, steep All snow conditions Black slopes (EU)/Double diamond (Noram)

- 5 cm

0 cm

+ 5 cm

+ 10 cm

+ TERRAIN (3) Race / On piste

All mountain Park & Pipe

Free – powder BC Touring

Groomed slopes Easy slopes

On piste 80% Off piste 20%

All terrain All conditions

+5 cm

+ 5 cm

+ 5 cm to + 10 cm

+ TYPE OF SKIS wanted (4) On piste

All mountain

Park & Pipe

Free – powder

BC Touring

S/Race S/Max (M & W) S/Force (M & W)

Stance (M & W) Distance (M & W)

NFX TNT

QST (M & W)

MTN Explore 88 & 95 (M & W) MTN SUMMIT 79

Men -> 0 to +5 cm Women -> -5 to 0 cm

Men -> +5 to +10 cm Women -> 0 to +5 cm

Men -> -5 to 0 cm Women -> -10 to -5cm

PROPOSED LENGTH = (1) + (2) + (3) + (4)

EXAMPLE: skier data: Man / 63 kg / intermediate / 80/20 / On Piste) => 160 +0 +5 +5 = 170 cm ski length (model: S/FORCE) RECOMMENDATIONS OF USE OF THE SKIS ACCORDING TO THE MASS OF THE SKIER : To guarantee the sufficient parameters of safety (i.e. the resistance of the screws to wrench), skiers must use skis, according to groups 1 to 4 (see page 7), corresponding with their weight.

SKI

TECHNICAL MANUAL ALPINE 2020/21

Men -> +2 to -2 cm Women -> -7 to -3 cm

6 summary <<<

SKI LENGTH GUIDE – JUNIOR

JUNIOR SKI LENGTH ACCORDING TO WEIGHT AND HEIGHT OF CHILDREN* Child Height

85 to 95 cm 95 to 105 cm 105 to 115 cm 115 to 125 cm 125 to 135 cm 135 to 145 cm 145 to 155 cm 155 to 165 cm 165 to 175 cm

Child Weight

10 to 14 kg

14 to 18 kg

18 to 22 kg

22 to 26 kg

26 to 30 kg

30 to 37 kg

37 to 45 kg

45 to 55 kg

55 to 65 kg

140 L L6 GW 150 L L6 GW

150 L L6 GW

130 L L6 GW

130 L L6 GW 140 L L6 GW

130 L L6 GW 140 L L6 GW 150 L L6 GW

150 L L6 GW 160 L L6 GW

130 L L6 GW

140 L L6 GW 150 L L6 GW 160 L L6 GW

160 L L6 GW

130 L L6 GW 140 L L6 GW

130 L L6 GW 140 L L6 GW 150 L L6 GW 120 N C5 GW 130 N L7 GW 140 N L7 GW

130 N L7 GW 140 N L7 GW

140 N L7 GW

110 N C5 GW 120 N C5 GW

110 N C5 GW 120 N C5 GW 130 N L7 GW

138 N L7 GW

138 N L7 GW 147 NR L10 GW

147 NR L10 GW 156 NR L10 GW

156 NR L10 GW 167 NR L10 GW

From 3 years old

Approx. Age of the > child

From 5 years old From 8 years old

Skiing Aptitude

L QST Max Jr S L QST Lux Jr S L S/ Max Jr S L S/Race Jr S L QST Max Jr M L QST Lux Jr M L S/ Max Jr M L S/Race Jr M

beginner intermediate

L C5 GW

80 L C5 GW

90 L C5 GW

beginner intermediate

100 L C5 GW

110 L C5 GW

120 L C5 GW

beginner intermediate good beginner

L S/RACE RUSH Jr

intermediate good beginner

N TNT Jr

intermediate good

N QST RIPPER L N QST RIPPER M N QST RIPPER S

120 L C5 GW

110 N C5 GW

intermediate good

167 NR L10 GW

* If weight is over 65 kg, SALOMON strongly recommend to use an ADULT ski.

EXAMPLE FOR T1 JR XS: A 4 year old child weighting 17 kg (and measuring 100 cm), with intermediate skiing abilities, must choose a 90 cm ski with a "C5 GW" binding. EXAMPLE FOR TNT JR: A 12 year old child weighting 37 kg (and measuring 145 cm), with intermediate skiing abilities, must choose a 140 cm ski with a "L7" binding.

SKI

TECHNICAL MANUAL ALPINE 2020/21

L QST Max Jr XS L QST Lux Jr XS L T1 XS + C5 GW

7 summary <<<

"G" NORMS SPECIFICATIONS

RECOMMENDATIONS OF USE OF THE SKIS ACCORDING TO THE MASS OF THE SKIER TO GUARANTEE THE SUFFICIENT PARAMETERS OF SAFETY (I.E. THE RESISTANCE OF THE SCREWS TO WRENCH), SKIERS MUST USE SKIS, ACCORDING TO GROUPS 1 TO 4 BELOW, CORRESPONDING WITH THEIR WEIGHT*.

GROUP OF SKI

MASS OF SKIER

> 65 kg

1, 2

≤ 65 kg

1, 2, 3

≤ 45 kg

(1, 2) 3, 4

25 kg

* extract from NF ISO 8364 june 2007

FULL DRILL ON "G" NORMS OPERATION

SKI G1

SKI G2

SKI G3

SKI G4

SKI TOURING

Ø of drill bit

4,1 mm

3,6 mm

4,1 mm

9,5 mm

Line depth of drilling* Tapping

7,5 mm NO

SALOMON glue

Recommended screwing torque

4 Nm

Skier weight*

OK for all skiers Mandatory for skiers >65kgs

< 65kg

3 Nm Hand screwdriver only to tighten the screws on the bindings

<45kg

*Extract from NF ISO 8364 (June 2007)

SKI

TECHNICAL MANUAL ALPINE 2020/21

Glue (put the glue at the bottom of the hole)

9,5 mm

8 summary <<<

<25kg

MAINTENANCE REPAIRS

SKI MAINTENANCE

MACHINE TUNING

A good ski maintenance is just as important for the recreational skier as for the racer. A well-prepared ski is a guarantee to maintain its performance (turns, grips, gliding, everything that makes the ski performing). The maintenance of a pair of skis involves 2 main steps: 1 – Daily check-up - at the end of everyday of skiing 2 – Machine tuning - for a reliable and precise "work"

DAILY CHECK UP

SKI CHECK-UP - Visually check to determine what needs to be tuned. - Remove major deep scratches on edges with whetstone. - Remove any traces of wax or grease. After this check-up, different steps have to be done in order to maintain properly the skis. The maintenance process can be adapted depending on the available machines (grinding, tuning, polishing, waxing, automatic machines or not). But basic steps as followed are recommended.

STEP 1 : FILL IN ANY HOLES IN THE BASE Superficial scratches : can desappear with a grinding machine (Step 2) Not very deep scratches or marks to be filled by machine: - Polyethylene: - Wait 10 minutes for the material to harden - Remove the excess polyethylene with a steel spatula for a flat surface - Proceed with the grinding machine (Step 2) ■ Deep cuts: - Cut out the damaged area - Cut a piece of the corresponding base material - Glue it into the damaged area - Hold it in place with a clamp and press repair (glue the piece with Loctite® 406 or slow Araldite) - Proceed with the grinding machine (Step 2) ■

- Visually check to see if any rust has developed on the edges. - Remove any traces with fine, 220-230 grit sandpaper. - If necessary, sharpen and polish edges using sandpaper wrapped around a file. - Clean the base and wax with Swix wax.

■

STEP 2 : STONE GRINDING Note: skis with plates or interfaces: please install binding-bridge kits. Note: always make the last grinding run in this direction: Tip-Tail. Concerning the machine parameters, please consult the machine manufacturer. ■ ■

BASE FINISHING SPECIFICATION

Please select the corresponding base structuring according to the model Whatever the structuring, make sure that it’s not visible on the steel edge, and it will have a negative impact on the performance.

Note: A too strong structure (in term of roughness) will degrade the behavior. IMPORTANT: The base and steel edge finishing should be carried out by trained personnel.

SKI

IN ORDER TO GET THE BEST ON THE SNOW, THERE ARE 3 TYPES OF STONE GRINDING STRUCTURING. ■ A1 : standard structuring (this standard structuring is working in most of snow conditions) ■ A2 : wave structuring ■ A3 : parallel diagonal structuring

TECHNICAL MANUAL ALPINE 2020/21

If the base is damaged, it must be grinded after the repair work. The structure should be smooth.

9 summary <<<

MAINTENANCE REPAIRS

STEP 3 : EDGE FINISHING STEEL EDGE TUNING SPECIFICATIONS According to the model, tune the skis using the requested specifications as explained below. This is the guarantee of the best performance. Alpine skis – Range 18

QST family – P&P – BC Touring

Models MTN Explore 88 – 88 W – 95 NFX - TNT QST 85 + Myriad 85

Edge tuning Steel edge angles: • Base side = 1,3° -> 1,5° • Lateral side = 1,5° -> 2°

Prefered Base finishing Grinding = A1

QST 92 + Lux 92 QST 99 + Lumen 99 QST 106 + Stella 106 QST 118 + QST Ripper

On Pist – All mountain skis

TECHNICAL MANUAL ALPINE 2020/21

RACE models (GS)

Edge tuning

Prefered Base finishing

S/RACE GS and GS FIS S/RACE SL FIS Jr and GS FIS Jr S/RACE PRO Jr GS and SL

Steel edge angles: • Base side = 0,8° ±0,3° • Lateral side = 2° → 2,5°

Grinding = A2

S/RACE PRO (SL) 165 – 157

Steel edge angles: • Base side = 0,5° ±0,3° • Lateral side = 2° → 2,5°

Grinding = A2

S/RACE SG FIS S/RACE PRO 182 – 175

Steel edge angles: • Base side = 1° ±0,3° • Lateral side = 2° → 2,5°

Grinding = A2

High performance on pist models & Light Touring

Edge tuning

Prefered Base finishing

S/RACE RUSH • S/MAX BLAST • S/FORCE BOLD

Grinding = A2

Steel edge angles: S/RACE SHOT • S/MAX 12 • S/MAX LTD • S/FORCE 11 • Base side = 1° ±0,3° • Lateral side = 1,5 → 2°

Grinding = A3

S/MAX W BLAST

Grinding = A1

S-Lab Minim – S/LAB X-Alp

Grinding = A3

Standard on pist models and others S/FORCE FEVER - 9 - 7 - 5 S/MAX 4 - 6 - 8 - 10 / W 4- W 6 - W 8 - W 10

Edge tuning Steel edge angles: • Base side = 1,3° ±0,3° • Lateral side = 1,5 → 2°

Prefered Base finishing Standard = A1

All Jr skis

All mountain models

Steel edge angles: • Base side = 1,3° ±0,3° • Lateral side = 1,5 → 2°

SKI

STANCE 102 STANCE 96 - STANCE 94 W STANCE 90 - STANCE 88 W DISTANCE

Edge tuning

10 summary <<<

Prefered Base finishing Standard = A1

MAINTENANCE REPAIRS

STEP 4: WAXING, SCRAPING AND BRUSHING

Some advice for having the best performing tuning:

TOOLS:

OFF SET POLISHING

• WAX REMOVER • IRON WITH THERMOSTAT • WAX APPLICATOR • PLASTIC SCRAPER • BRUSH

If possible, a 0,1 mm off set is recommended on the base side ▼

1. WAXING - It’s best to use melted wax. - Clean the base thoroughly. - Make sure the iron is set at the appropriate temperature so that only the wax is melted. (Temperature 110 °C +/- 5 oC or 230 °F +/- 10 °F). Excess heat (above 120 °C or 248 °F) can be harmful to both wax and ski, and can even cause permanent loss of glide qualities in the base.

> Advantage: The off set makes the ski extremely easy to turn - Make sure the stones are well lubricated. - Make sure the edges are not burnt (brown color). - Smooth (detuning) edges by hand with a stone (fig. B1) along the sidecut (for removing burrs), and with Scotch Brite® in tip and tail extremities (fig. B2).

- Choose a wax according to the wax manufacturer’s recommendations. - Melt the selected wax over the entire length of the base, and let the wax cool to room temperature.

2. SCRAPING - Remove the excess wax with a plastic scraper from tip to tail to leave only a very thin layer. - Remove wax from the base groove and ski edges as well.

- Brush the base with a nylon brush (or other type depending on the structure desired) working from tip to tail. - A rotating brush removes the structure of the base for good glide. Strap the skis together. Position the straps at the base contact points. Note: The skis can be stored ready-waxed (unscraped) for an extended period of time (e.g. between ski seasons).

DEFECTS TO ABSOLUTELY AVOID ▼

Base finishing

CLEANING THE SKIS

SKI

Pressurized cleaners are prohibited, as well as the following solvents: > Acetone > 95° alcohol (due to risk of damaging the cosmetics of the top surface of the ski).

TECHNICAL MANUAL ALPINE 2020/21

3. BRUSHING

11 summary <<<

MAINTENANCE REPAIRS

SKI TOURING

REPLACING THE TIP PROTECTOR WARNING !

TIP PROTECTOR WITHOUT SCREWS

Mounting zones are designed (visible) on the ski. It’s mandatory to respect the binding mounting zone as no binding screws should be positioned outside this area.

”Triangle” tip protector (fig. A). “Hexagonal” tip protector (fig. b).

BINDING MOUNTING

Concerned Models: > S/Lab Minim > S/Lab X-Alp > MTN EXPLORE 88 and MTN Explore 88 W > MTN Explore 95

1. Check that the tip protector is on the right position (Salomon logo on top foil side (fig. 1).

SKIN REPAIRING In case of damaged skins, a repair kit is available as a spare part. See below the content:

YES

2. Set ut the tip protector on the lateral groove with a rubber hammer (fig. 2).

TECHNICAL MANUAL ALPINE 2020/21

REFERENCE : L40289500001

3. Set up the tip protector on the central groove (fig. 3). 4. Finish the mounting on the second lateral groove with a rubber hammer (fig. 4).

4 REFERENCE : L40864200001

TIP PROTECTOR WITH SCREWS ”Triangle” tip protector (fig. E). “Hexagonal” tip protector (fig. F). 1. Insert the tip protector on the ski. 2. Place the 2 screws in the 2 holes face the running base and screw on (1N.m).

SKI

12 summary <<<

REFERENCE : L40864300001

BINDING

summary <<<

LIABILITY INDEMNIFICATION

ALPINE BINDING LIABILITY INDEMNIFICATION THE CHANGES TO OUR 2020-21 BINDING INDEMNIFICATION LIST REFLECT SALOMON USA’S POSITION REGARDING DISCONTINUATION OF SERVICE ON ANY BINDINGS WHICH ARE BEYOND THEIR USABLE LIFE. Each year, Salomon USA reviews its Binding Indemnification List. HOW TO READ THE LIST New models are added, and in some instances, older models are removed from the list. xxxxx > New models Older models are dropped to enhance the safety of skiers, and to encourage skiers not to use aged bindings for longer than their reasonably useful life. xxxxx > Current season model including new models In summary, skiers are best served when they are encouraged to stop using bindings that are deemed xxxxx > Final season model beyond their usable life by Salomon USA, or bindings which show excessive wear.

SALOMON RETAIL Season 2020/21 E M10 GW NR M10 GW NR M11 GW E M11 GW N C5 GW N L7 GW N S/LAB SHIFT MNC 10 N MTN PURE N MTN TOUR X12 TL GW N X12 TL GW E Z12 GW E Z10 GW NR L6 GW L L6 GW NR C5 GW

L C5 GW X 20 X 19 X 16 X 12 N S/LAB SHIFT MNC 13 N Guardian MNC 13 N STH2 WTR 16 N STH2 WTR 13 N Warden MNC 13 N Warden MNC 11 N Warden 11 N Z12 N Z 10 Ti W N Z10 N L10 N L7

< 2018 N Z12 Speed N Z12 Ti N Z12 Speed Ti N Z12 Ti Smartrak S Z12 Speed M XT12 M XT12 Ti M XT10 M XT10 Ti K Z12 Smartrak K Z12 Ti Smartrak K Z10 Smartrak K Z10 Ti Smartrak E Lithium 10 W E Mecury 10 E Mecury 11

E Z11 WALK E Z12 WALK H C5 SR N Guardian WTR 16 N Guardian WTR 13 N STH 16 Steel N STH 16 Driver N STH 14 Driver N STH 14 N STH 12 Driver N STH 12 Oversized N STH 10 N Z14 Speed S Z12 N Z10 FIS 20 J Z10 J Z12

J L10 E L7 Easytrak J L10 Junior N L9 / N L9W N T5 E C5 / E Ezytrak 5 Z 11 Z 10 Ti Axe + LZ 9 LZ 8 LZ 7 L9W L9

< 2018 NR Z 12 SC NR Z 10 SC NR Z11 WALK NR L10 SC NR L10 SR E Ezy 7 Easytrak NR L7 Easytrak E Mecury 11 E Mecury 10

E Z11 WALK E Z12 WALK E L10 Easytrak H C5 SR NR C5 Easytrak E Ezy 5 Easytrak K Z12 Smartrak K Z10 Smartrak NR L8 SC NR LZ7 SR

NR L9 W SC NR L9 W Easytrak NR L7 SR NR L7 SC NR Z12 Ti SC NR TZ5 SR NR TZ5 Junior Trak NR TZ5 SC / T5 SR / T5 SC NR Z12 Ti SC

NR TZ5 SR NR TZ5 Junior Trak NR TZ5 SC / T5 SR / T5 SC

NR Mecury 11 NR Z11 WALK N S14 N S12 NR S12 SC N S10 NR S10 SC

Season 2020/21 NR XM MNC 11 demo N WRT 20 N WRT 19 N WRT 16 N WRT 12 N WRT10 SRT 12 E MC 12

N C5 NR Warden MNC 13 Demo D Warden MNC 13 Demo NR Warden MNC 11 demo Last Year Prod 2019/20 X14 TL GW NR Z11 GW NR L10 GW E L10 GW N Guardian MNC 16 N MTN NR Warden 11 Demo F Warden 11 Demo E Lithium 10 NR Lithium 10

SALOMON RENTAL Season 2020/21 NR M10 GW NR M11 GW E Z10 GW NR L6 GW L L6 GW NR C5 GW L C5 GW NR WARDEN MNC 13 Demo NR WARDEN MNC 11 Demo

Last Year Prod 2019/20 NR Z11 GW NR L10 GW E L10 GW NR WARDEN 11 demo NR L10 Easytrak

STOECKLI RETAIL AND RENTAL

BINDING

TECHNICAL MANUAL ALPINE 2020/21

SCOTT RETAIL AND RENTAL

Season 2020/21 E M11 GW E M10 GW NR M10 GW N Warden MNC 13 Last Year Prod 2019/20 NR Warden MNC 11

NR Z11 GW N Warden MNC 13 NR Warden MNC 13 demo NR Warden 11 demo < 2018 N Warden 11 N BC 13

E MC 11 NR XM MNC 13 demo Last Year Prod 2019/20 < 2018 N SP12 Ti Speed N SP12 Speed

M AM12 M AM10 Ti K MC12 Ti K MC12 K MC10 Ti K MC10 NR 16 N SP10 Ti E ZI 11

TECNO PRO RETAIL AND RENTAL Season 2020/21 E MW100 E MW110 L LW55 L CW45 N CW45 N LW55 Last Year Prod 2019/20 E LW100 E LZ 110

< 2018 KR TX 120 N TL 75 N TC 45 E TL 75 E LT 100 E LT 100W E LW 110 E TC 45 KR TX110 N TL 100 CP

FACTION RETAIL AND RENTAL Season 2020/21 NR WARDEN MNC 11 DEMO F WARDEN MNC 11 DEMO NR WARDEN MNC 11 DEMO F WARDEN MNC 11 DEMO

Last Year Prod 2019/20 NR WARDEN MNC 11 DEMO F WARDEN MNC 11 DEMO

N TL 100 N TL 100 SC TL 100 ET N TL 90 N TL 90 W N TL 90 CP W TL 75 SC TL 75 ET TC 45 SR TC 45 ET

ROXY RETAIL AND RENTAL ■ Season 2020/21 E M10 GW L L6 GW L C5 GW

Last Year Prod 2019/20 ROXY C5 GW ROXY L6 GW ROXY L10 GW

< 2018 ROXY C5 Easytrak ROXY L7 Easytrak ROXY LITHIUM 10 Easytrak

ARMADA RETAIL AND RENTAL Season 2020/21 N SHIFT MNC 10 N TRACER TOUR E Z12 GW E M10 GW L L6 GW NR WARDEN MNC 11 DEMO NR M10 GW N SHIFT MNC 13 N STH2 WTR 16 summary <<<

N Warden MNC 13 NR Warden MNC 13 Demo D Warden MNC 13 Demo N Warden MNC 11

N L7 F Warden MNC 11 Demo E L10 GW L C5 GW

Last Year Prod 2019/20 E L10 GW NR C5 GW N STH2 WTR 13 N L10

< 2018 NR Lithium 10 E Lithium 10 NR C5 E C5

BINDING PREPARATION

PREPARATION Proper procedures for a certified technician to follow while mounting and adjusting Salomon Bindings. Therefore, rental bindings can be shipped without instructions or individual packaging. However, if these products are in fact sold, you absolutely have to supply your customer with the appropriate instructions. Upon request, Salomon will supply you with a document containing important information. The seven important steps to installing and adjusting are : 1. Preparation 2. Installation 3. Binding-to-boot adjustment 4. Release value selection and adjustment 5. Final check and system inspection 6. Mechanical inspection 7. Skier instruction and Warning

LIST OF TOOLS AND ACCESSORIES THAT ARE NECESSARY IN THE WORKSHOP Brakes - carving (=long arms) - wide brake Plates › For all other parts (such as AFD, housing, brakes, crews...), please consult your spare parts catalog.

TECHNICAL MANUAL ALPINE 2020/21

› Posidrive® screwdriver 7mm - ref. 000862 › Tap ref. 000816 › Brace ref. 000817 › Repair kit (2 extractor bits and repair plugs) ref. 000878 › Grease ref. 000905 › Glue ref. 000811 › 4.5 diameter plastic plugs (different references depending on the color see spare-parts catalog) › Specific adaptations: (for the references see spare-parts catalog)

BINDING

› Technical manuals for Skis and Bindings › Spare-parts catalogs › Release adjustment table (DIN chart) + skier type › Jigs (please consult spare-parts catalog for different references) › Synchro measuring device ref. 001189 › Electric drill › Drill bits (see on spare-parts catalog for different models) › Adjustment tool (Salomon screwdriver) ref. 000902 › Power screwdriver with torque release

15 summary <<<

INSTALLATION

WARNING : A Salomon toe or heel may not be mounted with another manufacturer’s toe or heel. Warranty are automatically voided for such mixed systems.

MOUNTING MOUNTING BINDINGS 1. Remove shrink wrap from skis. 2. Drill the skis using the appropriate jig and drill bit as shown in the chart opposite. Make sure that the jig is parallel to the ski during the entire drilling process (fig.1). 3. Follow the ski and binding manufacturers’ mounting instructions closely. It is necessary to use Salomon glue.

OPERATION

SKI G1 – G2

SKI G3 – G4

SKI TOURING

Ø OF DRILL BIT

4,1 mm

3,6 mm

4,1 mm

TAPPING

GLUE (put the glue at the bottom of the hole) TORQUE

SALOMON glue 3 Nm For these skis, use a hand screwdriver only to tighten the screws on the bindings.

4 Nm

SELECTING THE JIG SYNCHRO CENTER AND SYNCHRO RENTAL BINDING Ref.

Jigs

Skis Widths

001003

Rental Line Senior and Junior

56 mm <-> 99 mm

Application Synchro Center Adult - Synchro Rental Adult (Lenght drilling 9,5 mm) Z 12 - 10 SC L 9 - 10 SC & SR L 7 SC

BINDING

TECHNICAL MANUAL ALPINE 2020/21

(Lenght drilling 8 mm) L 7 SR Synchro Center Junior - Synchro Rental Junior (Lenght drilling 8 mm) T 5 SC – T 5 SR - C 5 SR

80 mm <-> 123 mm

001040

SYNCHRO RENTAL JIG 001003 A single mounting jig for Adult and Junior skis with the following positions: Adults (sizes 22-34) for skis > 140 cm. Junior (sizes 16-26.5) for skis 80-140 cm. RENTAL BINDINGS JIGS POSITIONS 001003 & 001040

Z12 SC Z10 SC L10 SC L9 SC L7 SC

Synchro C Senior

•

Synchro R Senior

L10 SR

L7 SR

C5 SR

•

Synchro C Junior

•

Synchro R Junior

•

Quadrax 3 R Soles Lenght

T5 SC

• 260 mm <-> 382 mm 268 mm <-> 348 mm 230 mm <-> 308 mm 216 mm <-> 304 mm 190 mm <-> 246 mm

>>> summary <<<

INSTALLATION

>>> ALL OTHER BINDINGS Ref.

Jigs

Skis Widths

L7840610001

Junior N C5 - N C5 GW Senior N Z12/ N Z10/N L10 Junior N L 7 - N L7 GW

56 mm <-> 99 mm

Junior (Lenght drilling 8 mm)

56 mm <-> 99 mm

Senior (Lenght drilling 9,5 mm)

L0011560001

Application

Junior (Lenght drilling 8 mm)

L0011570001 L3086300001 Easytrak (E C5 - E L7 - E L10 – E lithium 10 – E Mercury 11 & 10), Z10 GW, Z11 Walk/GW, Z12 Walk/GW, L L6 GW, L C5 GW, L10 GW, M10 GW, M11 GW L3267050001 Guardian 13&16 WTR & MNC L3298160001 STH2 WARDEN 13 MNC L3910910001 WARDEN 11, WARDEN 11 DEMO, WARDEN DEMO 13 MNC, WARDEN MNC 11, WARDEN MNC 11 DEMO L3816250001 MTN PURE & MTN TOUR L1184730001 X bindings X 20 – 18 – 16 - 12 L3989470001 S LAB SHIFT MNC 10 & 13

80 mm <-> 123 mm 70 > 116 mm

Senior (Length drilling 9.5 mm)

56 > 143 mm 56 > 143 mm

Senior (Length drilling 9.5 mm) Senior (Length drilling 9.5 mm)

56 > 143 mm

Senior (Length drilling 9.5 mm)

56 > 143 mm 60 mm <-> 86 mm

Senior (Length drilling 9.5 mm) Senior (Length drilling 9.5 mm)

56 > 143 mm

Senior (Length drilling 9.5 mm)

USING THE JIG The main function of a jig is to insure that all holes for mounting the binding are drilled in the correct location.

See chart to select the proper jig.

TECHNICAL MANUAL ALPINE 2020/21

1. Check that you have everything you need (the jig that corresponds to the binding, the right skis, the right boots). 2. Open the locking lever. 3. Open the jig by twisting both handles inward. Place the jig in the right direction on the ski.

Boot mid-sole mark

4. Place the jig on the ski and make sure that the jig remains properly aligned to the ski during the entire drilling operation (fig.1). - If the ski has a mid-sole mark, line up the mid-sole indicator on the jig with the midsole mark on the ski (fig.2). - If the ski has a tip-of-the-boot mark, line up the tip-of-boot-sole indicator on the jig with the tip-of-boot mark on the ski. - If the ski has no visible markings for jig location, consult the ski manufacturer for proper mounting position.

Ski

5. Once the jig is well-positioned on the ski, it is important to adjust the jig to the correct boot length to make sure the heel piece is in the proper position.

BINDING

6. Place the boot on the jig in the right direction. 7. Make sure the heel guide fits snugly against the boot heel. 8. Using the lever, lock the jig around the boot so it holds it without squeezing.

>>> summary <<<

INSTALLATION

>>> 3

FAT SKIS Refer to the spare parts catalog to know which jigs and brakes to use according the different ski widths and binding models. The reversible pads allow the jig to adapt to different ski widths (fig. 3).

Procedure for changing the pads to the other side: 1. Pull the pad off the arm of the jig. 2. Change the pad to the desired position. 3. Insert the pad into the arm of the jig. 4. R epeat this procedure: - On the other 3 arms for mounting the bindings symmetrically.

DRILLING 1. Follow the recommendations of the ski manufacturer for drilling and tapping. When in doubt about the ski’s core composition, select a 3.6 mm diameter bit, and drill one hole to see if any metal comes in contact with the bit. If contact is made with metal, re-drill with a 4.1 mm bit. 2. Drill through the jig’s proper bushings applying moderate downward pressure on the drill. Make sure that the countersink bevel on the drill bit has properly deburred the hole. 3. After drilling, turn the ski over and hit the base several times with the palm of your hand to remove any debris from the drilled holes.

BINDING

TECHNICAL MANUAL ALPINE 2020/21

DRILLING JUNIOR SKIS

- Use an 8 mm length drill bit to mount the Junior bindings L 7, N L7 GW, L 7 SR, T 5, T 5 SC & SR, C 5, N C5 GW, C 5 SR – Easytrak L7 & C5, L L6 GW, L C5 GW. - Whenever junior bindings are mounted on adult skis, there is an increased possibility for binding pull-out due to poor screw retention. The penetration depth of junior screws into the ski core is only 6 mm. If necessary, use adult screws and drill bits to penetrate any mounting platform. (For bindings mounted with adult binding screws, the penetration depth is the same.) - Y o u m u s t d r i l l a h o l e d e e p e n o u g h to accommodate the screw length you are using or damage to the ski base may result.

Drill bit length Length

Diameter

Skis

Diameter

Length Reference

Junior

4,1 mm

8 mm

000813

Ski Group 3 & 4

3,6 mm

8 mm

000814

Adult

4,1 mm

9,5 mm

000893

Ski Group 1 & 2

3,6 mm

9,5 mm

000892

Aspect

TAPPING

GLUE

MOUNTING

Tapping is usually done when the binding screw will come into contact with metal or in the following cases: - the material is too hard for a screw, - when the screw insertion would distort or stress the material holding the screw, - when recommended by the ski manufacturer. Failing to tap when necessary can result in top skin or sidewall delamination, broken screws or damage to the ski core.

Glue must be used when inserting binding screws to: - lubricate the screw during insertion, - create a watertight seal. Place a drop of glue on the surface of each hole. Caution: Salomon strongly recommends its own glue for Salomon skis.

Follow the mounting procedure and also refer to the section “Special cases in mounting”. A Posidrive® n°3 screwdriver, not a Phillips, must be used to mount Salomon bindings. Consult the Salomon Spare Parts Catalog for reference on Salomon screws. Caution: if a power screwdriver is used, adjust the clutch for the appropriate ski core cons truction (4 Nm maximum) to avoid stripping the threads. It is advisable to hand check each screw after mounting.

To use a Salomon tap and brace: 1. Position the brace so that the tap goes straight into the drilled hole. 2. Apply only enough pressure on the brace to start the tap. The tap is a self-cutting tool and you have only to turn the brace for the tap to cut its own way into the core. 3. Make 3 1/2 turns. 4. After tapping, turn the ski over and hit the base several times with the palm of your hand to remove any shavings from the hole. summary <<<

INSTALLATION

GENERAL MOUNTING 1

6 7 8

1. Heel lever 2. Indicator window 3. Brake pad 4. AFD plate 5. Height adjustment screw 6. Heel cup axis 7. Heel cup 8. Release adjustment screw 9. Lenght adjustment 10. Heel housing 11. Heel plate 12. Brake arms 13. Wings toe adjustment

6 7 8 8

BINDING

TECHNICAL MANUAL ALPINE 2020/21

19 summary <<<

INSTALLATION

BINDING BRAKE MODELS

BRAKING CAPACITY

TECHNICAL MANUAL ALPINE 2020/21

SKI SET STAND HEIGHT IN mm

THE BRAKING CAPACITY IS DEPENDENT ON THE WEIGHT AND THE HEIGHT OF THE SKI + BINDING SET. PLEASE, REFER TO THE GRAPH BELOW 60 58 56 54 52 50 48 46 44 42 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 0

FT BRAKE 80 FT BRAKE 90 FT BRAKE 100 FT BRAKE 115 FT BRAKE 130

L BRAKE 80 L BRAKE 90 L BRAKE 100 L BRAKE 115

FT BRAKE 80

L BRAKE 80

C BRAKE 90

FT BRAKE 100 FT BRAKE 115 FT BRAKE 130

L BRAKE 100 L BRAKE 115 SET SKI

L BRAKE 80

C BRAKE 90

SH BRAKE 90

C BRAKE 115 C BRAKE 130

SH BRAKE 110 SH BRAKE 120

L BRAKE 80 L BRAKE 90 L BRAKE 100 L BRAKE 115 FT BRAKE 80 FT BRAKE 90 FT BRAKE 100 CFTBRAKE BRAKE90115 CFTBRAKE BRAKE100 130 C BRAKE 115 C BRAKE 130 L BRAKE 80 L BRAKE 90 L BRAKE 100 SH BRAKE115 90 L BRAKE SH BRAKE 100 SH BRAKE 110 SH BRAKE 120 C BRAKE 90 C BRAKE 100 C BRAKE 115 JC BRAKE BRAKE 75 130 J BRAKE 85 SH BRAKE 90

FT BRAKE 80 FT BRAKE 90 FT BRAKE 100 FT BRAKE 115 FT BRAKE 130 L BRAKE 80 L BRAKE 90 L BRAKE 100 L BRAKE 115 FT BRAKE 80 FT BRAKE 90 FT BRAKE 100 FT BRAKE 115 FT BRAKE 130

C BRAKE 90 C BRAKE 100 C BRAKE 115 C BRAKE 130

L BRAKE 80 L BRAKE 90 L BRAKE 100 L BRAKE 115

SH BRAKE 90 SH BRAKE 100 SH BRAKE 110 SH BRAKE 120

C BRAKE 90 C BRAKE 100 C BRAKE 115 C BRAKE 130

J BRAKE 75 J BRAKE 85

SH BRAKE 90 SH BRAKE 100 SH BRAKE 110 SH BRAKE 120

R BRAKE 75 R BRAKE 80 R BRAKE 90 R BRAKE 100 R BRAKE 115 R BRAKE 130

J BRAKE 75

BRAKE 70 200 400 600FT BRAKE 800 1000 1600 2200 2400 3800 100 2600 2800SH3000 L BRAKE 90 1800 2000C BRAKE J BRAKE 85 4000 4200J24400 BRAKE3200 100 3400 3600 90 1200 1400

FT BRAKE 80

C BRAKE 115

C BRAKEIN 130GRAM WEIGHT

400 600 800 1000 1200 1800902000 2200 24001002600 2800SH3000 BRAKE 3200 100 3400 C BRAKE FT BRAKE 90 1400 1600 L BRAKE

SH BRAKE 110 RSHBRAKE BRAKE75120 R BRAKE 80 R BRAKE 90 R BRAKE 100 BRAKE 115 75 RJ BRAKE 3600 3800 BRAKE 85 4000 RJ BRAKE 130

J2 BRAKE 80 J2 BRAKE 90

R BRAKE 75

4200 4400 R BRAKE 80

B 75 DG B 80 DG B 90 DG B 100 DG B 115 DG B 130 DG

BINDING

R BRAKE 90 R BRAKE 100 J2 BRAKE 70 R BRAKE 115 J2 BRAKE 80 R BRAKE 130 J2 BRAKE 90 J BRAKE 75 SH BRAKE 90 L BRAKE 80 R BRAKE 75 C BRAKE 90 J2 BRAKE 70 J BRAKE 85 SH BRAKE 100 BRAKE 90 R BRAKE 80 C BRAKE 100 This graphLL indicates (1/2 pair binding), accept. to comply with BRAKEFailure 80 SH+BRAKE 110 the maximum height and weightR that BRAKE 100 for a ski set BRAKEthe 90 brake can J2 C BRAKE 115 ski + plate BR 75 DG during SH BRAKE 120 ski set in the event of loss of the L BRAKE 115 the braking BRAKE 100 use. J2 BRAKE 90 these values reduces and stopping capacity of your ski C BRAKE 130 600 1800 2000 2200 2400 2600 2800 3000 3200 3400 3600 3800 4000 4200 4400 BR 80 DG 115 BRAKE BR 90 DG 130 BRAKE B 100 DG STAND HEIGHTR DEFINITION BRAKE 75 J BRAKE 75 B 75 DG C BRAKE 90 SH BRAKE 90 BJ2115BRAKE DG 70 1000 1200 1400 1600 1800 2600 2800J BRAKE 3000 853200 3400R3600 4000 4200 4400 BRAKE 3800 80 B 80 DG C BRAKE 1002000 2200 SH2400 BRAKE 100 BJ2130 DG BRAKE 80 R BRAKE 90 B 90 DG C BRAKE 115 SH BRAKE 110 J2 BRAKE 90 R BRAKE 100 B 100 DG C BRAKE 130 SH BRAKE 120 R BRAKE 115 B 115 DG R BRAKE 130 B 130 DG R BRAKE 75 SH BRAKE 90 B 75 DG J BRAKE 75 BRAKE 70 600 1800 2000 2200 2400100 2600 2800J BRAKE 3000 853200 3400R3600 4000 J2 4200 4400 BRAKE 3800 80 SH BRAKE B 80 DG J2 BRAKE 80 R BRAKE 90 SH BRAKE 110 B 90 DG J2 BRAKE 90 R BRAKE 100 SH BRAKE 120 B 100 DG R BRAKE 115 B 115 DG R BRAKE 130 B 130 DG B 75 DG J BRAKE 75 R BRAKE 75 J2 BRAKE 0 2400 2600 2800 3000 3800 440070 B 80 DG J BRAKE3200 85 3400 3600 R BRAKE 80 4000 4200 J2 BRAKE 80 B 90 DG R BRAKE 90 SKI BRAKE J2 BRAKE 90 B 100 DG R BRAKE 100 SKI R BRAKE 115 B 115 DG B 130 R BRAKE 130 STAND HEIGHT = Distance between theDG top of the brake base and the ski base B 75 DG R BRAKE 75 20 J2 BRAKE 70 0 3000 3200 3400 3600 3800 B 80 DG R BRAKE 80 4000 4200 4400 J2 BRAKE 80 B 90 DG R BRAKE 90 summary <<< J2 BRAKE 90 B 100 DG R BRAKE 100 B 115 DG R BRAKE 115 FT BRAKE 100 FT BRAKE 115 FT BRAKE 130

L BRAKE 100 L BRAKE 115

FT FT FT FT FT

LB LB LB LB

CB CB CB CB

SH SH SH SH

JB JB

RB RB RB RB RB RB

J2 J2 J2

B7 B8 B9 B1 B1 B1

BINDING TO BOOT ADJUSTMENTS

ADJUSTING Once the binding has been mounted, it is necessary to make the proper binding-to-boot adjustments. All Salomon bindings may be closed manually by simply lifting the heel lever. Adjustments must be re-checked every time boots are changed. Use the following procedure.

WING ADJUSTMENT 1. M anual adjustment (fig. A1): only one adjustment screw, which is located on the left side of the toe piece. - Place the boot in the binding (closed position). - Loosen the micrometric screws to loosen the wings. - Check that the tip of the boot sole is flush against the butt plate (fig. A2). This contact is made when the boot has lateral play. Do not over tighten, the boot may no longer be centered. 2. A utomatic adjustment: the wings on the toe cup are self-adjusting.

NOK

MODELS STH2 WTR 13 & 16 GUARDIAN WTR & MNC 13 & 16 WARDEN 13 MNC & WARDEN 13 MNC DEMO WARDEN 11 & WARDEN 11 DEMO WARDEN MNC 11 WARDEN MNC 11 DEMO

WING ADJUSTMENT

TOE HEIGHT ADJUSTMENT

simultaneous

Manual Thickness of the mounting instruction sheet

automatic

WING ADJUSTMENT

AFD PLATE ADJUSTMENT

automatic

Manual Thickness of the mounting instruction sheet

C5 GW - L6 GW L7 GW - L10 GW Z10 GW -Z11 GW Z12 GW M10 GW - M11 GW C5 – L7 – L10 – LITHIUM 10 – MERCURY 10 & 11 – Z10 - Z12 – Z14 -

BINDING AFD HEIGHT ADJUSTMENT With the boot in the binding, raise the AFD plate by turning the adjustment screw, located on the side of toe base plate, counter clockwise. - Pull the boot back to create a gap between the boot sole and the binding AFD pedal. - Go up the AFD plate height by turning the adjustment screw clockwise to obtain the recommended gap (see the following chart (fig. B3). Note: Always check the forward pressure after making toe adjustments

MODELS

S LAB SHIFT MNC 10 & 13

BINDING

- With the boot in the binding, raise the toe by turning the adjustment screw, located on top of the toe piece, counter clockwise. - Pull the boot back to create a gap between the boot sole and the binding AFD. - Lower the toe height by turning the adjustment screw clockwise to obtain the recommended gap (see the following chart (fig. B1-B2). - For models with automatic wing and automatic height adjustments: make forward pressure adjustment only. See instructions in following chapteras. Note: Always check the forward pressure after making toe adjustments.

TECHNICAL MANUAL ALPINE 2020/21

TOE HEIGHT ADJUSTMENT

B3 21 summary <<<

BINDING TO BOOT ADJUSTMENTS FORWARD PRESSURE ADJUSTMENT WITH TOOL LESS AND TAB ADJUSTMENT With the boot in the binding (closed position), make sure the arrow. The extremity of the tab for the version without arrow, line up within the scribed area of the heel housing.

XTRACK MXT, WARDEN MNC 13 DEMO, WARDEN MNC 11, WARDEN MNC 11 DEMO, Z11 WALK/GW, Z12 WALK/GW, Z10 GW, L10 GW

✘

LEISURE TRAK WITH M10 GW, M11 GW

TECHNICAL MANUAL ALPINE 2020/21 BINDING

✓

✘

EASYTRAK +, EC5-EL7-EL10, L L6 GW, L C5 GW

✘

✓

✘

EASYTRAK WITH LITHIUM 10, WARDEN 11 & DEMO 11, MERCURY 10 & 11

If this adjustment is incorrect, remove the boot from the binding, lift the adjustment tab to slide the heel into the desired position. Re-insert the boot to check the adjustment.

✘

✓

✘

✓

✘

SMARTRAK + KZ

✘

✓

LIGHTRAK + JL

✘ ✓

✘

RENTAL SC & SR

✘ summary <<<

✓

✘ >>>

BINDING TO BOOT ADJUSTMENTS L & Z MODELS N L7, N L7 GW, N L10, N Z10

✘

✓

✘

JUNIOR BINDING N C5, N C5 GW

✘

✓

✘

WITH SCREW ADJUSTMENT

✘

✓

✘

X19 LAB, X20LAB

✘

✓

✘

GUARDIAN MNC, WARDEN MNC 13, STH2 WTR

✘

✓

✘

✓

✘

STH

S LAB SHIFT MNC 10 & 13

✘

✓

✘

BINDING

X16LAB, X12LAB, X12 TL, X14 TL, X12 TL GW, X14 TL GW

TECHNICAL MANUAL ALPINE 2020/21

With the boot in the binding (closed position), adjust the forward pressure to align the top of the head screw with the back of the heel part.

23 summary <<<

BINDING TO BOOT ADJUSTMENTS

BOOTS & BINDING COMPATIBILITIES BOOT INSPECTION Most boots are manufactured in accordance with the ISO 5355 standard specification for «Alpine» ski boot dimensions. Most alpine touring boots are manufactured in accordance with ISO 9523 standard specification for «Alpine Touring» ski boot dimensions. These standard norms concern not only the shape and dimensions as illustrated below, but also the

friction coefficient of the area of the sole which is in contact with anti-friction plate on the binding. These standards help to ensure compatibility with the binding, according to ISO 9462 and ISO 13992. Alpine norm ISO 5355: Designed for use with a pair of classic skis with alpine bindings and not with a monoski, snowboard or skiboard.

Touring norm ISO 9523: Designed for use with a pair of touring bindings, and not with alpine bindings, monoski, snowboard or skiboard. It is the skier’s own responsibility if (s)he chooses to take the additional risks. Your ski boots must be assembled, adjusted, and checked by an authorized dealer.

BOOT MODIFICATION Any performance or fit modification of a boot that could effect the function between the boot and binding should be inspected to verify that

the boot meets Standard Alpine Boots Norms and Touring Boots Norms. Mechanical inspection is recommended after any such modification.

STANDARD BOOT SOLE DIMENSIONS

BINDING

TECHNICAL MANUAL ALPINE 2020/21

■ BOOT HEEL

■ BOOT TOE

LEGEND (measurements in mm) ALPINE ADULT BOOT DIN - ISO 5355

ALPINE CHILDREN BOOT DIN - ISO 5355

TOURING ADULT BOOT DIN - ISO 9523

69 ± 2

62 ± 2

71 ± 6

100 (L<300mm)

80 (L<240mm)

120 (L ≥300mm)

90 (L ≥240mm)

5±1

3±1

5±1

19 ± 1

16.5 ± 1.5

28 ± 3

30 ± 2

25 ± 2

40 ± 10

30 ± 1

27.5 ± 2

32 ± 2

4±1

3±1

4±1

8±1

41.5 ± 3.5

35 ± 3

18 ± 1.5

16 ± 2

37 ± 4

27 ± 3

36.25 ± 0.75

34.5 ± 1

summary <<<

≥ 70

BINDING TO BOOT ADJUSTMENTS

BOOT TO BINDING COMPATIBILITY Before drilling the ski, be sure the boot you are using is compatible with the binding. Only boots that conform with applicable standards may be used with Salomon bindings. If a boot sole is warped, worn or improperly canted, such that there is more than a 1 mm difference in sole flatness measured across its width, the boot is incompatible.

BOOT NORMS

OTHER COMPATIBILITY PROBLEMS YOU MAY ENCOUNTER

• Tread, grid pattern or insignia present in the AFD area of the boot sole. This area must be flat over it entire surface. • Non-compatible boot sole composition. Lowgrade thermoplastic (T.P.) boots may not be used with Salomon bindings. If you are uncertain as to the quality of the boot sole material, perform the Clean vs. Lubricated Test.

• Boot manufacturers who display on the boot one of the following markings: DIN or ISO, guarantee that they use standard norms. In the absence of any of these, check first with the boot manufacturer. • Cut-outs in the boot sole that prevent the brake from engaging properly. • Excessive ramping or wear of the boot sole at the point where it contacts the binding. Any wear that inhibits binding function is excessive.

ALPINE SKI BOOTS (ISO 5355)

BINDING LOGO

BINDING DIN MINI

TYPE A (ADULT)

TYPE C (CHILDREN)

Without any indication/logo

≤2

● ●

●

≥3

When in doubt, replace the boot.

GRIPWALK SKI BOOTS

TYPE A (ADULT)

TYPE C (CHILDREN)

WTR SKI BOOTS (ISO 9523)

TOURING SKI BOOTS (ISO 9523)

TOURING SKI BOOTS NO COMPLIANT WITH ISO 9523

TYPE A (ADULT)

Binding stamped with

PIN Binding

≤2

●

≥3

● ●

●

● ●

●

●*

No DIN

●*

* Bindings with pins require boots with compatible inserts. Consult an authorized dealer

CHILDREN BOOT TO BINDING COMPATIBILITY Only adult norm boots may be used with adult bindings. Under no circumstances should a children norm boot ever be used with an adult binding. The added width of an adult norm boot sole somewhat limits the shock absorption capability of these models and they should not be used with a boot sole longer than 304 mm. As a result, it is recommended that an aggressive junior skier with an adult norm boot sole use a model designed exclusively for adult norm boots.

CHILDREN * NORM BOOT SOLE TYPE C Adaptable GripWalk pads kit Alpine version QST Access 70T S/Race 90 S/Race 70 S/Max 65 / S/Race 65 T3 / T3RT / T3RT Girly S/Max 60TM & L / S/Race 60TM & L T2RT / T2RT girly /T2 Team T1 / T1 Girly

18-21 18-21 15-18

summary <<<

Yes Yes Yes

ADULT NORM BOOT SOLE TYPE A Alpine version 22-28,5 22-27,5 22-26,5 22-26,5 22-26,5 22-26,5

Adaptable GripWalk pads kit

Yes No No Yes Yes Yes

TECHNICAL MANUAL ALPINE 2020/21

Binding stamped with

●

BINDING

≤2

BINDING TO BOOT ADJUSTMENTS

BOOTS & BINDING COMPATIBILITIES

ISO 5355

NORME

BOOTS SOLE

ALPINE

BINDINGS MODEL

ALPINE

ALPINE BOOTS with Pads available as spare parts: S MAX / S PRO / S PRO HV / S MAX 65 / S RACE 65 ALPINE BOOTS with Pads available as spare parts: X PRO / QUEST PRO / QST ACCESS ALPINE BOOTS with Pads available as spare parts: X ACCESS

WTR

GRIPWALK

MNC

NO NORM

X, Z, L, C, C5 GW, L7 GW, STH2 16 & 13 WTR XTRACK, LITHIUM, M10 GW, M11 GW GUARDIAN MERCURY 10&11, L6 GW, L10 GW 16 & 13 WTR WARDEN 11, Z10&Z11&Z12 GW WARDEN 11 DEMO, ISO 9462 ISO 9462 STH & & ISO 13992 ISO 13992 ISO 9462

ALL ALPINE BOOTS in their selling configurations: S MAX / S RACE / X PRO / S PRO / S PRO HV / X ACCESS / QUEST PRO / QST PRO / QST ACCESS / S MAX 60T / S RACE 60T

ALL ALPINE BOOTS in their selling configurations: SHIFT PRO

GRIPWALK

Reference spare part piece

C O M P A T I B L E

WARDEN MNC 13 WARDEN MNC 13 DEMO WARDEN MNC 11 WARDEN MNC 11 STH2 16 & 13 WTR DEMO C5 GW, L7 GW, M10 GW, M11 GW GUARDIAN 16&13 MNC L6 GW, L10 GW ISO 9462 S/LAB SHIFT Z10&Z11&Z12 GW & MNC 10 & 13 ISO 13992 ISO 9462 & ISO 13992

ISO 9462 & ISO 13992

Touring PADS

ALPINE BOOTS with Pads available as spare parts: QST PRO

Touring tech PADS (with inserts)

ALPINE BOOTS with Pads available as spare parts: QST PRO

Touring sole + Inserts

MTN Lab MTN Explore (Men and Women)

MTN PURE MTN TOUR

BINDING

TECHNICAL MANUAL ALPINE 2020/21

ALPINE BOOTS with Pads available as spare parts: Kit "JUNIOR Adult" on S RACE 60 / S MAX 60 T (size 22-26) / T3

26 summary <<<

BOOTS & BINDING COMPATIBILITIES

BINDINGS INTENDED TO BE USED ONLY WITH:

ALPINE BOOTS COMPLIANT WITH ISO 5355 STANDARD

✖

WTR

SYNCHRO CENTER AND SYNCHRO RENTAL BINDING. . . . SMARTRAK BINDING. . . . . . . . . . . . . . . . . . . . SMARTRAK GRIP / GRIP PLUS BINDING. . . . . . . . . . LIGHTRAK PLATE J L & H L BINDING. . . . . . . . . . . . X12 TL & X14 TL BINDING. . . . . . . . . . . . . . . . . . X12 & X16 BINDING. . . . . . . . . . . . . . . . . . . . . JUNIOR RACE PLATE/JUNIOR RACE PEDAL KIT BINDING.. X TRACK PLATE WITH XT BINDING. . . . . . . . . . . . . SPEED PLATE + Z BINDING. . . . . . . . . . . . . . . . . EASYTRAK PLATE WITH L&C BINDING. . . . . . . . . . . EASYTRAK PLATE WITH LITHIUM BINDING. . . . . . . . . EASYTRAK PLATE WITH MERCURY BINDING. . . . . . . . WARDEN 11 BINDING. . . . . . . . . . . . . . . . . . . . WARDEN 11 DEMO BINDING. . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . .

ISO 9523

28 30 31 32 33 34 35 37 39 41 43 46 48 50

WARNING THESE ALPINE BINDINGS ARE INTENDED TO BE USED ONLY WITH THE FOLLOWING SKI BOOTS: > Alpine ski boots compliant with ISO 5355 standard. Any use with other ski boots could cause the ski-binding-boot system to be faulty and affect release characteristics, which would increase the risk of serious injury while skiing. Therefore, skiers are warned not to use this product with any ski boots other than those meeting the standards indicated above. Skiers are advised to consult the dealer where this product was purchased, or an equipment specialist at any SALOMON authorized ski dealer of this product, for further information regarding which ski boots meet the standards listed above.

TECHNICAL MANUAL ALPINE 2020/21

✖

BINDING

✖ ISO 5355

27 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

SYNCHRO CENTER AND SYNCHRO RENTAL BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WARNING : BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT TO ISO 5355 STANDARD

✖

ISO 5355

WTR

✖

ISO 9523

Any use with other ski boots could cause the ski-binding-boot system to be faulty and affect release characteristics, which would increase the risk of serious injury while skiing. Therefore, skiers are warned not to use this product with any ski boots other than those meeting the standards indicated above. Skiers are advised to consult the dealer where this product was purchased, or an equipment specialist at any SALOMON authorized ski dealer of this product, for further information regarding which ski boots meet the standards listed above.

SOLE LENGTH ADJUSTMENT

Z & L SC (Synchro center) : 260mm – 384mm 1. Position the rental jig (ref. 001003 or 001040 for a fat ski rental) on the ski.

TECHNICAL MANUAL ALPINE 2020/21

PREPARATION It is important to maintain consistent procedures when mounting any Salomon binding. Any boot used with a Salomon rental binding must be visually inspected for compatibility. To use the Synchrosysteme you need: - Synchrosysteme jig references 001003 and 001040. - adjustment tool reference 000902.

2. Then drill through the jig’s proper bushings. Follow the same procedure as for retail bindings (drilling, tapping, glue). 3. Mount the premounted track assembly orienting the sticker toward the back of the ski (fig. 1). 4. Mount the heel aligning the holes, and tighten the screws (fig. 2). 5. Mount the brake according to the usual procedure.

The bindings that are compatible with the Synchrosysteme are the following: Z12 SC. Z10 SC. L10 SC. L 9 SC. L10 SR. L7 SC. L7 SR. T5 SC. C5 SR. The Synchrosysteme can be used with all Alpine boots (DIN, ISO 5355) from all brands. The measuring device can be used if skiers come in the shop with their boots on.

SYNCHRO RENTAL For mounting Synchro Rental bindings, follow the same procedure as for the retail bindings.

SYNCHRO CENTER

CONTENTS OF THE BOX

BINDING

› The heel mounted on a plate,

› The toe mounted on a sliding plate, › The position indicator, › The premounted track assembly with yellow screw (Adult skis). Caution: the toes mounted on the sliding plate are specific to RENTAL products. › Brake. summary <<<

>>>

MODEL - SPECIFIC INSTRUCTIONS >>>

SYNCHRO CENTER AND SYNCHRO RENTAL BINDING

6. To Position the toe piece: - Place the toe, mounted on the sliding plate, in front of the track and slide it until it stops. - Depress the manual adjustment button (located on the front of the toe) and slide the toe all the way back. - Slide the indicator forward and clip it on the sliding plate (fig. 3) either manually or with a flat Salomon screwdriver (ref. 000902).

7. To take the toe off the track: - Place the toe on the A position of the position indicator. - Unclip the position indicator with a flat Salomon screwdriver (fig. 4). - Depress the manual toe adjustment button ; this way, the toe can slide forward off the track.

Easy glide manual heel adjustment: - Position the boot in the toe piece. - With one finger, simply lift the adjustment loop at the back of the heel and slide it forward until the binding cup contacts the boot heel. - Release the loop, push boot down and check the forward pressure adjustment. To do this, you should see a little metal guide in the indicator (fig. 1). Note: If a correction is necessary, reopen the heel to move it and then re-check.

›R elease value adjustment: The bindings must be adjusted by using the Adjustment chart. › Visual and mechanical inspection: Whenever a binding looks particularly dirty or if visual inspection reveals that something may be wrong with the system, the system should be cleaned, lubricated and subjected to mechanical inspection. summary <<<

BINDING

BINDING TO BOOT ADJUSTMENTS WITHOUT USING THE SYNCHROSYSTEME

TECHNICAL MANUAL ALPINE 2020/21

INDICATOR

MODEL - SPECIFIC INSTRUCTIONS

SMARTRAK BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WARNING : BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT TO ISO 5355 STANDARD CONTENTS OF THE BOX › 2 Toes mounted on a sliding part › 2 Heels mounted on a sliding part › 2 Brakes › 2 Thin Plates › 1 Notice SOLE LENGTH ADJUSTMENT

MOUNTING 1. I nsert the Thin Plate in the seating ahead the plate (fig. 1).

257mm – 380mm

2. Place it correctly with a rotational motion (fig. 2). 3. From the rear, slide the Toe piece on the interface until it corresponds with or is just above your boot sole length using the manual lock to authorize the sliding (fig. 3a & 3b). 4. From the rear, slide the Heel piece on the interface until it corresponds with or is just above your boot sole length using the manual lock to authorize the sliding (fig. 4). 5. Mount the Brake following the usual procedure (fig. 5)

ADJUSTING EXAMPLE

6. Identify the length of the boot. 7. If you have boot sole L 306 mm, adjust the Toe on the 308 mm mark. The range in this case is 301 mm to 308 mm (fig. 7).

8. If you have chosen the L 306 mm, adjust the Heel piece on the 312 location. The range in this case is 305 mm to 312 mm (fig. 8). 9. Step in the boot and check forward pressure (fig. 9). The arrow on the housing must be within the scribed area.

BINDING

TECHNICAL MANUAL ALPINE 2020/21

30 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

SMARTRAK GRIP / GRIP PLUS BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WARNING : BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT TO ISO 5355 STANDARD CONTENTS OF THE BOX › 2 Toes › 2 Heels mounted on a sliding part › 2 Brakes › 2 Thin Plates › 1 Notice

MOUNTING AND AJUSTING

1. Insert the Thin Plate in the seating ahead the plate (fig. 1). 2. Place it correctly with a rotational motion (fig. 2). 3. Identify the length of the boot. 4. Identify the letter that corresponds your sole length. (If you are between two, choose the higher one) (fig. 3).

5. Screw the center mounting track to this letter. (4Nm Torque) (fig. 4). Mount the Toe piece as usual (fig. 5). 6. From the rear, slide the Heel piece on the interface using the manual lock to authorize the sliding (fig. 6).

6 TECHNICAL MANUAL ALPINE 2020/21

8. Position your boot in the toe and slide the heel until it touches the boot (fig. 8). 9. Step in the boot and check forward pressure (fig. 9). The arrow on the housing must be within the scribed area Info: The rear N° is an indication for a quick adjustment of the second ski (fig. 10).

OK BINDING

7. Mount the Brake following the usual procedure (fig. 7).

31 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

LIGHTRAK PLATE J L & H L BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WARNING : BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT TO ISO 5355 STANDARD

SOLE LENGTH ADJUSTMENT

260mm – 373mm

MOUNTING AND AJUSTING

TECHNICAL MANUAL ALPINE 2020/21

1. Open and set the blade in straight position and place it on the plate with a rotational motion (fig. 1). 2. Identify the length of the boot sole. 3. Mounting of the toe piece: - J L model: Identify the letter that corresponds the sole length and screw the toe piece (if you are between two letters, choose the higher one). - H L model: From the rear, slide the toe piece on the interface until it corresponds with or is just above the sole length, push the bolt until the “clic” to lock on the toe piece (fig. 2). Note: to move the toe, insert a screwdriver and with a rotational motion lock off the bolt (fig. 3). 4. Mounting of the heel piece: J L model: - From the rear, slide the heel piece on the interface using the manual lock to authorize the gliding (fig. 4). - Mount the brake following the usual procedure (fig. 5). - Position the boot in the toe and slide the heel until it touches the boot. - Step in the boot and check forward pressure, the arrow on the lock must be within the scribed area (fig. 6). Note: the rear N° on the blade is an indication for a quick adjustment of the second ski. H L model: - From the rear, slide the heel piece on the interface using the manual lock to authorize the gliding (fig. 4). - Mount the brake following the usual procedure (fig. 5). - Slide the heel piece until it corresponds with or it just above the sole length. - Step in the boot and check forward pressure, the arrow on the lock must be within the scribed area (fig. 6).

BINDING

32 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

X12 TL & X14 TL BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WARNING : BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT TO ISO 5355 STANDARD

✖

WTR

ISO 5355

✖

ISO 9523

SOLE LENGTH ADJUSTMENT

MOUNTING & ADJUSTING Open the central lever (fig. 1).

Insert the toe piece and position on the track according to the boot sole length (fig. 2).

When the binding is adjusted to the sole length, locked the central lever (fig. 4). Select and adjust the setting release values for toe and heel pieces. Step-in the boot, check and adjust the forward pressure (fig. 5).

Adjust spindle only when boot is out of the binding

BINDING

TECHNICAL MANUAL ALPINE 2020/21

Insert the heel piece and position on the track according to the boot sole (fig. 3).

33 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

X12 & X16 BINDING

TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WARNING : BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT TO ISO 5355 STANDARD DRILLING SKIS 1. For mounting the X 12 & X 16 bindings on skis, holes have to be drilled with the Salomon mounting jig (ref. 11847301) to ensure a proper alignment of the binding. Sole Monting Mounting lengts oh Heel rail of toe rail in mm

2. Check the boot sole length you would like to mount the binding for and drill the “S” ; “M” holes which are marked on the jig following the instructions in the chart below : Toe PIECE POSITION on the toe rail

Bootcenter related to the "real" bootcenter position in mm

265 275 285 295 305 315 325 335 345 355 max 360

"S" "S" "S" "S" "S" "M" "M" "M" "M" "M" "M"

"M" "M" "M" "M" "M" "M" "M" "M" "M" "M" "M"

3.Drill your chosen setup and remove the mounting jig. Note: The X 12 & X 16 bindings have an additional hole in the middle to fix the brake, don’t forget to drill this hole.

Position 7 Position 7 Position 7 Position 6 Position 5 Position 5 Position 4 Position 3 Position 3 Position 2 Position 2

Maximum of positions to adjust the boot center +/-

"+"... forward "-"... backward

Forward

Backward

+ 7,0 mm + 2,0 mm - 3,0 mm - 0,5 mm + 2,0 mm - 3,0 mm - 0,5 mm + 2,0 mm - 3,0 mm - 0,5 mm - 3,0 mm

+2 +2 +3 +4 +1 +3 +2 +3 +2 +2 +2

0 -1 -1 -1 -2 -1 -1 -1 -1 -1 0

MOUNTING PROCEDURE

BINDING

TECHNICAL MANUAL ALPINE 2020/21

1. Mount the base plate toe by tightening the screws at min. 4 Nm.

Screw to fix the brake

2. Mount the heel base plate by tightening the screws at min. 4 Nm and mount the brake by tightening the screws in the middle at min. 4 Nm. 3. Push the “VAR” lever over to the right and slide the toe piece from the middle towards the tip of the ski. 4. Move the toe piece to the number corresponding to the boot sole length you would like to mount the binding for. 5. Slide the heelpiece from the tail forward. 6. Match up the steel band with the boot sole length you would like to mount the binding for. 7. Take the “AFD” pedal and place it in the middle and fix it with screw at max. 4 Nm. 8. Put the boot into the binding and check the forward pressure. The screw head needs to be aligned with the housing. 1 2 Toe piece

34 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

JUNIOR RACE PLATE BINDING JUNIOR RACE PEDAL KIT BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WARNING : BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT TO ISO 5355 STANDARD

J-RP SJ-RP J-RP S S J-RP M J-RP J-RP M M J-RP LJ-RP J-RP L L B Pos. AC BAD CB D C Pos. D A Pos. B Pos. AC BAD CB D C DPos. A Pos. B Pos. AC BAD CB D C D Pos. A Pos. 285 285 305 305 315 315 mm 285mm 255mm 235255 225235 255 225 235mm 225305mm 275mm 255275 245255 275 245 255 245 mm 315mm 285mm 265285 255265 285 255 265 255 275 245 295 265295 265 295 265 305 275305 275 305 275 Junior race plates are premounted in factory. 3 sizes are available (S – M275 – L) 245275 245 265 265 265 285 285 285 295 295 295

Junior race plate are compatible with bindings: > N Z12 > N Z10 > N L10 > N L7

MOUNTING & ADJUSTING 1. Check the boot sole length you would like to mount 2. Put the toe piece to the letter corresponding to the boot sole length (A – B – C – D). 3. Mount the toe by tightening the screws at min. 4 Nm

4. Mount the heel by tightening the screws at min. 4 Nm 5. Put the boot onto the binding and check the forward pressure.

S (225-285) M (245-305) L (255-315)

MID SOLE CENTERED Mounting on ski S-M-L min 225 235 245 255

265

275

285 295 305 315

"S" "S" "S" "M" "S" "M" "L" "S" "M" "L" "S" "M" "L" "S" "M" "L" "M" "L" "M" "L" "L"

«Boot center related to the Ski center according to the Toe poition» A +10 mm +5 mm Centered +10 mm -5 mm +5 mm +10 mm Centered +5 mm -5 mm Centered -5 mm

(«+» = Forward «-» = Backward) B C +5 mm Centered -5 mm +5 mm -10 mm Centered +5 mm -5 mm Centered -10 mm -5 mm -10 mm summary <<<

Centered -5 mm -10 mm Centered -15 mm -5 mm Centered -10 mm -5 mm -15 mm -10 mm -15 mm -

Maximun of positions to adjust Boot center

D -5 mm -10 mm -15 mm -5 mm -10 mm -5mm -15 mm -10 mm -15 mm -

1 2 3 1 3 2 1 3 3 2 2 3 3 1 3 3 2 3 1 2 1

BINDING

Sole lenght (in mm)

TECHNICAL MANUAL ALPINE 2020/21

A B C D

>>>

MODEL - SPECIFIC INSTRUCTIONS >>>

JUNIOR RACE PLATE AND JUNIOR RACE PEDAL KIT

JUNIOR RACE PLATE (J-RP2) BOOT SOLE LENGTH: Mounting information on the plate for L 7, Z 10 and Z 12 A. 217mm – 246mm B. 237mm – 266mm C. 256mm – 285mm D. 276mm – 305mm

D C B A

A B C D

D C B A

WARNING ON L7 BINDING

BINDING

TECHNICAL MANUAL ALPINE 2020/21

1. MOUNTING OF THE TOE AND HEEL ON JUNIOR RACE PLATE In case of L7 binding with a screw setting up of 6mm, please to not use a screw gun.

3. PEDAL MOUNTING INSTRUCTION

2. SELECTION OF THE TOE PEDAL In case of mounting an L7 binding on the Junior race plate, the choice of the toe pedal is depending on the type of boot used.

In the junior race kit pedal (reference L3916910001), you have the following components:

36 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

X TRACK PLATE WITH XT BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WARNING : BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT TO ISO 5355 STANDARD

✖

ISO 5355

WTR

✖

ISO 9523

SOLE LENGTH ADJUSTMENT

261mm – 381mm

TECHNICAL MANUAL ALPINE 2020/21

MOUNTING & ADJUSTING 1. R emove the grey plastic part from the ski blade before toe assembly.

▼

2. Insert the toe piece from the front and position on the track according to the boot sole length.

BINDING

▼

>>> summary <<<

MODEL - SPECIFIC INSTRUCTIONS >>>

X TRACK PLATE WITH XT BINDING

3. Insert the heel and break piece from the back and position on the track according to the boot sole length.

▼

4. Boot sole length adjustmen.

▼

5. Step in the boot and check forward pressure.

6. Select and adjust the setting release values for toe and heel pieces.

▼

BINDING

TECHNICAL MANUAL ALPINE 2020/21

▼

38 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

SPEED PLATE + Z BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WARNING : BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT TO ISO 5355 STANDARD

✖

ISO 5355

WTR

✖

ISO 9523

MOUNTING & ADJUSTING 1 – For mounting Z Speed bindings on skis, holes have to be drilled with the Salomon mounting jig (ref 11139301) to ensure a proper alignment of the binding. 2 – Mount the rear plate by tightening the screws at 4 N.m.

3 – Mount the front plate by tightening the screws at 4 N.m.

▼

>>>

TECHNICAL MANUAL ALPINE 2020/21

260mm – 360mm

BINDING

SOLE LENGTH ADJUSTMENT

39 summary <<<

MODEL - SPECIFIC INSTRUCTIONS >>>

SPEED PLATE + Z BINDING

4 – Press and open the central lever.

8 – Close and lock on the central lever.

▼

9 – Step in the boot and check the forward pressure. 5 – Mount the brake by tightening the screw at 4 N.m with tool Torx 25.

▼

6 – Slide the toe piece from the front backward and the heel piece from the tail forward.

▼

7 – Select the length of the sole boot and adjust the toe and heel pieces at the length corresponding.

BINDING

TECHNICAL MANUAL ALPINE 2020/21

▼

40 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

EASYTRAK PLATE WITH L&C BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WARNING : BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT TO ISO 5355 STANDARD

✖

ISO 5355

WTR

✖

ISO 9523

TECHNICAL MANUAL ALPINE 2020/21

Size S: 197mm – 304mm / Size M: 229mm – 336mm / Size L: 273mm – 380mm

MOUNTING & ADJUSTING EASYTRAK L7

EASYTRAK L7, L9 & L 10 ▼

EASYTRAK L7

1 – Insert the toe piece from the front and position on the track according to the boot sole length.

3 – Assemble the break.

▼

2 – Insert the heel piece from the back and position on the track according to the boot sole length.

▼

4 – Step in the boot and check forward pressure.

EASYTRAK L7

▼

BINDING

SOLE LENGTH ADJUSTMENT

NOK

Ref: 6517801K

Printed in France

>>>

summary <<<

NOK

MODEL - SPECIFIC INSTRUCTIONS EASYTRAK PLATE WITH L&C BINDING

EASYTRAK C5

>>>

EASYTRAK C5

1 – Insert the toe piece from the front and position on the track according to the boot sole length.

3 – Step in the boot and check forward pressure.

▼

2 – Insert the heel piece from the back and position on the track according to the boot sole length.

EASYTRAK C5

▼

NOK

Ref: 6517801K

example showing adjustment for boot size 295

NOK

TECHNICAL MANUAL ALPINE 2020/21

NOK

BINDING

ef: 6517801K Ref: 6517801K Printed in France Printed in France

42 summary <<<

Printed in France

MODEL - SPECIFIC INSTRUCTIONS

EASYTRAK PLATE WITH LITHIUM BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WARNING : BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT TO ISO 5355 STANDARD

✖

ISO 5355

WTR

✖

ISO 9523

Ski Woman (W): 253mm – 320mm / Size L: 257mm – 380mm

MOUNTING & ADJUSTING

FRONT plate

TECHNICAL MANUAL ALPINE 2020/21

1. Use the Salomon mounting jig (ref:30863001) and drill the skis following the ski and binding manufacturer’s instructions. Mount the front and rear plate on the ski by tightening the screws at 4 N.m. ▼

REAR plate

BINDING

Below view

43 summary <<<

>>>

MODEL - SPECIFIC INSTRUCTIONS >>>

EASYTRAK PLATE WITH LITHIUM BINDING

2. Insert the toe piece from the front and position on the track according to the boot sole length ▼

3. Insert the heel and break piece from the back and position on the track according to the boot sole length ▼

BINDING

TECHNICAL MANUAL ALPINE 2020/21

4. Boot sole length adjustment ▼

>>>

44 summary <<<

MODEL - SPECIFIC INSTRUCTIONS >>>

EASYTRAK PLATE WITH LITHIUM BINDING

5. Step in the boot and check forward pressure ▼

BINDING

TECHNICAL MANUAL ALPINE 2020/21

6. Select and adjust the setting release values for toe and heel pieces ▼

45 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

EASYTRAK PLATE WITH MERCURY BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WARNING : BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT TO ISO 5355 STANDARD

✖

ISO 5355

WTR

✖

ISO 9523

MOUNTING & ADJUSTING

Ski Woman (W): 253mm – 320mm / Size L: 257mm – 380mm

1. Use the Salomon mounting jig (ref:30863001) and drill the skis following the ski and binding manufacturer’s instructions. Mount the front and rear plate on the ski tightening the screws at 4 N.m.

BINDING

TECHNICAL MANUAL ALPINE 2020/21

SOLE LENGTH ADJUSTMENT

>>>

46 summary <<<

MODEL - SPECIFIC INSTRUCTIONS EASYTRAK PLATE WITH MERCURY BINDING

3. Boot sole length adjustment

4. Step in the boot and check forward pressure

5. Select and adjust the setting release values for toe and heel pieces

TECHNICAL MANUAL ALPINE 2020/21

2. Insert the toe and the heel piece and position on the track according to the boot sole length.

BINDING

>>>

47 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

WARDEN 11 BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WARNING : BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT TO ISO 5355 STANDARD

✖

ISO 5355

WTR

✖

ISO 9523

WARNING THESE ALPINE BINDINGS ARE INTENDED TO BE USED ONLY WITH THE FOLLOWING SKI BOOTS: > Alpine ski boots compliant with ISO 5355 standard.

MOUNTING & ADJUSTING 1 - For mounting Warden 11 binding on skis, holes have to be drilled with the Salomon mounting jig (ref 39109101) to ensure a proper alignment of the binding. Mount the toe piece and the rear plate on ski by tightening the screws at 4 N.m.

BINDING

TECHNICAL MANUAL ALPINE 2020/21

>>>

48 summary <<<

MODEL - SPECIFIC INSTRUCTIONS WARDEN 11

3. Step in the boot.

4. Adjust the toe height with adjustment screw until to create a gap of the thickness of the mounting instruction sheet between the boot sole and the binding (fig. 4).

5. Check and adjust the forward pressure.

6. Select and adjust the setting release values for toe and heel pieces.

TECHNICAL MANUAL ALPINE 2020/21

2. Insert the heel and brake piece from the back and align the brake indicator with marking on the plate.

6 BINDING

>>>

49 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

WARDEN 11 DEMO BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WARNING : BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT TO ISO 5355 STANDARD

✖

ISO 5355

WTR

✖

ISO 9523

MOUNTING & ADJUSTING

262mm – 382mm

1. For mounting Warden 11 DEMO binding on skis, holes have to be drilled with the Salomon mounting jig (ref 39109101) to ensure a proper alignment of the binding. Mount the toe piece and the rear plate on ski by tightening the screws at 4 N.m.

2. Insert the heel and brake piece from the back and position on the plate according to the bot sole length.

BINDING

TECHNICAL MANUAL ALPINE 2020/21

SOLE LENGTH ADJUSTMENT

50 summary <<<

>>>

MODEL - SPECIFIC INSTRUCTIONS >>>

WARDEN 11 DEMO

3. Insert the toe piece from the front and position on the plate according to the boot sole length.

4. Boot sole length adjustment.

5. Step in the boot.

L = 305

8. Select and adjust the setting release values for toe and heel pieces.

TECHNICAL MANUAL ALPINE 2020/21

7. Check and adjust the forward pressure.

BINDING

6. Adjust the toe height with adjustment screw until to create a gap of the thickness of the mounting instruction sheet between the boot sole and the binding.

51 summary <<<

BOOTS & BINDING COMPATIBILITIES

BINDINGS INTENDED TO BE USED ONLY WITH FOLLOWING SKI BOOTS:

ALPINE BOOTS COMPLIANT WITH ISO 5355 STANDARD SKI BOOTS EQUIPPED WITH “GRIPWALK” PADS

✖

BINDING

TECHNICAL MANUAL ALPINE 2020/21

ISO 5355

✖

WTR

N C5 GW BINDINGS. . . . . . . . . . . . . . . . . . . . . N L7 GW BINDINGS. . . . . . . . . . . . . . . . . . . . . JUNIORTRAK PLATE WITH C5 GW BINDING.. . . . . . . . JUNIORTRAK PLATE WITH L6 GW BINDING.. . . . . . . . EASYTRAK PLATE WITH L10 GW BINDING. . . . . . . . . EASYTRAK PLATE WITH Z11 GW & Z10 GW BINDING.. . . . LEISURE TRAK PLATE WITH M10 GW & M11 GW BINDINGS.. FLEXTRAK PLATE WITH Z12 GW BINDING.. . . . . . . . . X12 TL GW & X14 TL GW. . . . . . . . . . . . . . . . . .

. . . . . . . . .

ISO 9523

53 55 57 59 61 63 65 67 69

WARNING THESE ALPINE BINDINGS ARE INTENDED TO BE USED ONLY WITH THE FOLLOWING SKI BOOTS: > Alpine ski boots compliant with ISO 5355 standard. > Ski boots equipped with « GripWalk » labelled kit of walking soles Any use with other ski boots could cause the ski-binding-boot system to be faulty and affect release characteristics, which would increase the risk of serious injury while skiing. Therefore, skiers are warned not to use this product with any ski boots other than those meeting the standards indicated above. Skiers are advised to consult the dealer where this product was purchased, or an equipment specialist at any SALOMON authorized ski dealer of this product, for further information regarding which ski boots meet the standards listed above.

52 summary <<<

N C5 GW BINDINGS TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT WITH ISO 5355 STANDARD AND SKI BOOTS EQUIPPED WITH « GRIPWALK » LABELLED KIT OF WALKING SOLES

✖ ISO 5355

✖

WTR

ISO 9523

WARNING THESE ALPINE BINDINGS ARE INTENDED TO BE USED ONLY WITH THE FOLLOWING SKI BOOTS: > Alpine ski boots compliant with ISO 5355 standard. > Ski boots equipped with « GripWalk » labelled kit of walking soles WITHOUT metal inserts Any use with other ski boots could cause the ski-binding-boot system to be faulty and affect release characteristics, which would increase the risk of serious injury while skiing. Therefore, skiers are warned not to use this product with any ski boots other than those meeting the standards indicated above. Skiers are advised to consult the dealer where this product was purchased, or an equipment specialist at any SALOMON authorized ski dealer of this product, for further information regarding which ski boots meet the standards listed above.

ALPINE SKI BOOTS (ISO 5355) TYPE A (Adult)

●

GRIPWALK BOOTS (ISO 9523)

TYPE C TYPE A (Children) (Adult)

●

NO NORM TYPE C (Children)

●

2. Screw the base, taking care to hold it so that it does not rotate. Then slide the toe until it comes into contact with the holder screw and tighten the 2 screws at 3 N.m

BINDING

1. For mounting N C5 GW binding on skis, holes have to be drilled with the Salomon mounting jig (ref L7840610001) to ensure a proper alignment of the binding.

TECHNICAL MANUAL ALPINE 2020/21

MOUNTING & ADJUSTING

53 summary <<<

>>>

MODEL - SPECIFIC INSTRUCTIONS >>>

N C5 GW BINDINGS

3. Mount the heel taking care to tighten the 4 screws in the order indicated below at 3 N.m.

In case the forward pressure is not good, move the heel by the lever with the help of a screwdriver as explained in the images below.

5. Select and adjust the setting release values for toe and heel pieces. Concerning the DIN setting of the heel, the end of the green indicator must be aligned with the number

BINDING

TECHNICAL MANUAL ALPINE 2020/21

4. Step-in the boot and check the forward pressure

54 summary <<<

N L7 GW BINDINGS TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT WITH ISO 5355 STANDARD AND SKI BOOTS EQUIPPED WITH « GRIPWALK » LABELLED KIT OF WALKING SOLES

✖ ISO 5355

✖

WTR

ISO 9523

WARNING THESE ALPINE BINDINGS ARE INTENDED TO BE USED ONLY WITH THE FOLLOWING SKI BOOTS: > Alpine ski boots compliant with ISO 5355 standard. > Ski boots equipped with « GripWalk » labelled kit of walking soles WITHOUT metal inserts Any use with other ski boots could cause the ski-binding-boot system to be faulty and affect release characteristics, which would increase the risk of serious injury while skiing. Therefore, skiers are warned not to use this product with any ski boots other than those meeting the standards indicated above. Skiers are advised to consult the dealer where this product was purchased, or an equipment specialist at any SALOMON authorized ski dealer of this product, for further information regarding which ski boots meet the standards listed above.

ALPINE SKI BOOTS (ISO 5355) TYPE A (Adult)

●

GRIPWALK BOOTS (ISO 9523)

TYPE C TYPE A (Children) (Adult)

●

NO NORM TYPE C (Children)

●

1. For mounting N L7 GW binding on skis, holes have to be drilled with the Salomon mounting jig (ref L0011570001 or L0011560001) to ensure a proper alignment of the binding.

BINDING

TECHNICAL MANUAL ALPINE 2020/21

MOUNTING & ADJUSTING

55 summary <<<

MODEL - SPECIFIC INSTRUCTIONS >>>

N L7 GW BINDINGS

2. S crew the holder screw, taking care to hold it so that it does not rotate.Then slide the toe until it comes into contact with the holder screw and tighten the 2 screws. at 3 N.m

3. Mount the heel taking care that the filter is well assembled and taking care to tighten the 4 screws in the order indicated below at 3 N.m.

4. M ount the brake on the heel, taking care that the 2 brake lugs are correctly engaged in the 2 housings of the heel base.

In case the forward pressure is not good, move the heel by the lever with the help of a screwdriver as explained in the images below (a).

â&#x20AC;&#x192; 6. S elect and adjust the setting release values for toe and heel pieces.

BINDING

TECHNICAL MANUAL ALPINE 2020/21

5. Step-in the boot and check the forward pressure.

56 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

JUNIORTRAK PLATE WITH C5 GW BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT WITH ISO 5355 STANDARD AND SKI BOOTS EQUIPPED WITH « GRIPWALK » LABELLED KIT OF WALKING SOLES

✖

WTR

ISO 5355

ISO 9523

WARNING THESE ALPINE BINDINGS ARE INTENDED TO BE USED ONLY WITH THE FOLLOWING SKI BOOTS: > Alpine ski boots compliant with ISO 5355 standard. > Ski boots equipped with "GripWalk" and with "GripWalk Junior" labelled kit of walking soles WITHOUT metal inserts Any use with other ski boots could cause the ski-binding-boot system to be faulty and affect release characteristics, which would increase the risk of serious injury while skiing. Therefore, skiers are warned not to use this product with any ski boots other than those meeting the standards indicated above. Skiers are advised to consult the dealer where this product was purchased, or an equipment specialist at any SALOMON authorized ski dealer of this product, for further information regarding which ski boots meet the standards listed above. ALPINE SKI BOOTS (ISO 5355)

Size XS (premounted in factory): 197mm – 257mm Size S: 220mm – 304mm

TYPE A (Adult) C5 GW

BINDING MODELS

●

GRIPWALK BOOTS (ISO 9523)

NO NORM

TYPE C TYPE A (Children) (Adult)

●

TYPE C (Children)

●

TECHNICAL MANUAL ALPINE 2020/21

SOLE LENGTH ADJUSTMENT

●

MOUNTING & ADJUSTING 1 - For mounting C5 GW binding on skis, holes have to be drilled with the Salomon mounting jig (ref 30863001) to ensure a proper alignment of the binding.

REAR

FRONT

Mount the front and the rear plate on ski by tightening the screws at 3 N.m (ski G3&G4)

BINDING

Drill bit length Length

Diameter

Skis

Diameter

Length Reference

Junior

4,1 mm

8 mm

000813

Ski Group 3 & 4

3,6 mm

8 mm

000814

summary <<<

Aspect

>>>

MODEL - SPECIFIC INSTRUCTIONS >>>

JUNIORTRAK PLATE WITH C5 GW BINDING

2. Insert the toe and the heel piece and position on the track according to the boot sole length.

4. Select and adjust the setting release values for toe and heel pieces.

Concerning the DIN setting of the heel, the end of the green indicator must be aligned with the number.

BINDING

TECHNICAL MANUAL ALPINE 2020/21

3. Step-in the boot and check the forward pressure.

58 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

JUNIORTRAK PLATE WITH L6 GW BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT WITH ISO 5355 STANDARD AND SKI BOOTS EQUIPPED WITH « GRIPWALK » LABELLED KIT OF WALKING SOLES

✖

WTR

ISO 5355

ISO 9523

WARNING THESE ALPINE BINDINGS ARE INTENDED TO BE USED ONLY WITH THE FOLLOWING SKI BOOTS: > Alpine ski boots compliant with ISO 5355 standard. > Ski boots equipped with"GripWalk" and with "GripWalk Junior" labelled kit of walking soles WITHOUT metal inserts Any use with other ski boots could cause the ski-binding-boot system to be faulty and affect release characteristics, which would increase the risk of serious injury while skiing. Therefore, skiers are warned not to use this product with any ski boots other than those meeting the standards indicated above. Skiers are advised to consult the dealer where this product was purchased, or an equipment specialist at any SALOMON authorized ski dealer of this product, for further information regarding which ski boots meet the standards listed above. ALPINE SKI BOOTS (ISO 5355)

Size M: 253mm – 336mm

TYPE A (Adult) BINDING MODELS

L6 GW

●

GRIPWALK BOOTS (ISO 9523)

TYPE C TYPE A (Children) (Adult)

●

NO NORM TYPE C (Children)

TECHNICAL MANUAL ALPINE 2020/21

SOLE LENGTH ADJUSTMENT

●

MOUNTING & ADJUSTING 1 - For mounting L6 GW binding on skis, holes have to be drilled with the Salomon mounting jig (ref 30863001) to ensure a proper alignment of the binding.

Drill bit length

BINDING

Length

Diameter

Skis

Diameter

Length

Reference

Junior

4,1 mm

8 mm

000813

Aspect

Ski Group 3&4

3,6 mm

8 mm

000814

Adult

4,1 mm

9,5 mm

000893

3,6 mm

9,5 mm

000892

Ski Group 1&2

summary <<<

>>>

MODEL - SPECIFIC INSTRUCTIONS >>>

JUNIORTRAK PLATE WITH L6 GW BINDING

> > > Mount the front and the rear plate on ski by tightening the screws at 4 N.m (ski G1/G2) or 3 N.m (ski G3/G4).

2. Insert the toe and the heel piece and position on the track according to the boot sole length.

4. Select and adjust the setting release values for toe and heel pieces.

Concerning the DIN setting of the heel, the end of the green indicator must be aligned with the number

BINDING

TECHNICAL MANUAL ALPINE 2020/21

3. Step-in the boot and check the forward pressure.

60 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

EASYTRAK PLATE WITH L10 GW BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT WITH ISO 5355 STANDARD AND SKI BOOTS EQUIPPED WITH « GRIPWALK » LABELLED KIT OF WALKING SOLES

✖ ISO 5355

✖

WTR

ISO 9523

Ski Woman (W) premounted in factory: 253mm – 320mm / Size L: 257mm – 380mm

SOLE LENGTH ADJUSTMENT

MOUNTING & ADJUSTING

ALPINE SKI BOOTS (ISO 5355) TYPE A (Adult)

TYPE C (Children)

●

✖

GRIPWALK BOOTS (ISO 9523)

NO NORM SKI BOOTS

●

✖

TECHNICAL MANUAL ALPINE 2020/21

1. For mounting L10 GW binding on skis, holes have to be drilled with the Salomon mounting jig (ref 30863001) to ensure a proper alignment of the binding.

Drill bit length

BINDING

Length

Diameter

Skis

Diameter

Length

Reference

Adult

4,1 mm

9,5 mm

000893

3,6 mm

9,5 mm

000892

Aspect

Ski Group 1&2

61 summary <<<

>>>

MODEL - SPECIFIC INSTRUCTIONS >>>

EASYTRAK PLATE WITH L10 GW BINDING

2. Mount the front and the rear plate on ski by tightening the screws at 4 N.m

BINDING

TECHNICAL MANUAL ALPINE 2020/21

3. Insert the toe and the heel piece and position on the track according to the boot sole length.

â&#x20AC;&#x192; 4. Step-in the boot and check the forward pressure

5. Select and adjust the setting release values for toe and heel pieces

62 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

EASYTRAK PLATE WITH Z11 GW & Z10 GW BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT WITH ISO 5355 STANDARD AND SKI BOOTS EQUIPPED WITH « GRIPWALK » LABELLED KIT OF WALKING SOLES

✖ ISO 5355

✖

WTR

ISO 9523

SOLE LENGTH ADJUSTMENT

Ski Woman (W): 253mm – 320mm / Size L: 257mm – 380mm

MOUNTING & ADJUSTING

ALPINE SKI BOOTS (ISO 5355) TYPE A (Adult)

TYPE C (Children)

●

✖

GRIPWALK BOOTS (ISO 9523)

NO NORM SKI BOOTS

●

✖

TECHNICAL MANUAL ALPINE 2020/21

1 - For mounting Z11 Walk binding on skis, holes have to be drilled with the Salomon mounting jig (ref 30863001) to ensure a proper alignment of the binding.

BINDING

Mount the front and the rear plate on ski by tightening the screws at 4 N.m

63 summary <<<

>>>

MODEL - SPECIFIC INSTRUCTIONS >>>

EASYTRAK PLATE WITH Z11 GW & Z10 GW BINDING

2. Insert the toe and the heel piece and position on the track according to the boot sole length.

4. Step-in the boot and check the forward pressure.

5. Select and adjust the setting release values for toe and heel pieces

BINDING

TECHNICAL MANUAL ALPINE 2020/21

3. Boot sole length adjustment.

64 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

LEISURE TRAK PLATE WITH M10 GW & M11 GW BINDINGS TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT WITH ISO 5355 STANDARD AND SKI BOOTS EQUIPPED WITH « GRIPWALK » LABELLED KIT OF WALKING SOLES

✖ ISO 5355

✖

WTR

ISO 9523

WARNING

ALPINE SKI BOOTS (ISO 5355) TYPE A (Adult)

TYPE C (Children)

●

✖

Size M: 253mm – 320mm / Size L: 257mm – 380mm

MOUNTING & ADJUSTING 1

NO NORM SKI BOOTS

●

✖

BINDING

1. For mounting M10&M11 GW bindings on skis, holes have to be drilled with the Salomon mounting jig (ref 30863001) to ensure a proper alignment of the binding.

GRIPWALK BOOTS (ISO 9523)

TECHNICAL MANUAL ALPINE 2020/21

THESE ALPINE BINDINGS ARE INTENDED TO BE USED ONLY WITH THE FOLLOWING SKI BOOTS: > Alpine ski boots compliant with ISO 5355 standard. > Ski boots equipped with « GripWalk » labelled kit of walking soles WITHOUT metal inserts

65 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

BINDING

TECHNICAL MANUAL ALPINE 2020/21

>>>

LEISURE TRAK PLATE WITH M10 GW & M11 GW BINDINGS

2. M ount the front and the rear plate on ski by tightening the screws at 4 N.m

3. Insert the toe and the heel piece and position on the track according to the boot sole length.

4. S tep-in the boot and check the forward pressure. The forward pressure must be in the “OK” area.

5. S elect and adjust the setting release values for toe and heel pieces.

66 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

FLEXTRAK PLATE WITH Z12 GW BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT WITH ISO 5355 STANDARD AND SKI BOOTS EQUIPPED WITH « GRIPWALK » LABELLED KIT OF WALKING SOLES

✖ ISO 5355

✖

WTR

ISO 9523

WARNING

ALPINE SKI BOOTS (ISO 5355) TYPE A (Adult)

TYPE C (Children)

●

✖

257mm – 380mm

GRIPWALK BOOTS (ISO 9523)

NO NORM SKI BOOTS

●

✖

TECHNICAL MANUAL ALPINE 2020/21

MOUNTING & ADJUSTING 1

BINDING

1. Insert the toe and the heel piece and position on the track according to the boot sole length.

67 summary <<<

>>>

MODEL - SPECIFIC INSTRUCTIONS >>>

FLEXTRAK PLATE WITH Z12 GW BINDING

2. Boot sole length adjustment.

4. Select and adjust the setting release values for toe and heel pieces

BINDING

TECHNICAL MANUAL ALPINE 2020/21

3. Step-in the boot and check the forward pressure.

68 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

X12 TL GW & X14 TL GW TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT WITH ISO 5355 STANDARD AND SKI BOOTS EQUIPPED WITH « GRIPWALK » LABELLED KIT OF WALKING SOLES

✖ ISO 5355

✖

WTR

ISO 9523

WARNING

TO BE COMPATIBLE WITH GRIPWALK BOOTS, THE CENTRAL LEVER OF THE PLATE MUST BE MARKED WITH THE GRIPWALK LOGO. WITHOUT THIS LOGO ON THE LEVER, COMPATIBILITY IS NOT POSSIBLE.

TYPE A (Adult)

TYPE C (Children)

●

✖

GRIPWALK BOOTS (ISO 9523)

NO NORM SKI BOOTS

●

✖

GRIPWALK COMPATIBILITY EXCLUSION OLD GRIPWALK DESIGN - VERSION 1

CURRENT GRIPWALK DESIGN - VERSION 2

NO GAP BETWEEN FRICTION AREA AND CRAMPON

NO COMPATIBILITY of K2 BFC boot with GripWalk outsole Version 1 summary <<<

BINDING

SOLE LENGTH ADJUSTMENT

ALPINE SKI BOOTS (ISO 5355)

TECHNICAL MANUAL ALPINE 2020/21

OK COMPATIBILITY of K2 BFC boot with Gripwalk outsole version 2

MODEL - SPECIFIC INSTRUCTIONS >>>

X12 TL GW & X14 TL GW

1. Open the central lever.

4. When the binding is adjusted to the sole length, locked the central lever, and check that the lever is completely closed.

2. Insert the toe piece and position on the track according to the boot sole length.

5. Select and adjust the setting release values for toe and heel pieces. Step-in the boot, check and adjust the forward pressure.

3. Insert the heel piece and position it on the track according to the boot sole.

BINDING

TECHNICAL MANUAL ALPINE 2020/21

MOUNTING & ADJUSTING

70 summary <<<

BOOTS & BINDING COMPATIBILITIES

MNC (MULTI-NORM CERTIFIED) BINDINGS ARE INTENDED TO BE USED WITH FOLLOWING SKI BOOTS:

ALPINE BOOTS COMPLIANT WITH ISO 5355 STANDARD TOURING BOOTS COMPLIANT WITH ISO 9523 STANDARD

SKI BOOTS EQUIPPED WITH “WTR TECHNOLOGY” PADS OR WITH “GRIPWALK” PADS

. . . . . .

72 74 76 78 80 84

WARNING THESE ALPINE BINDINGS ARE INTENDED TO BE USED ONLY WITH THE FOLLOWING SKI BOOTS: > Alpine ski boots compliant with ISO 5355 standard. > Touring boots compliant with ISO 9523 standard > Ski boots equipped with “WTR technology” pads or with “GRIPWALK” pads Any use with other ski boots could cause the ski-binding-boot system to be faulty and affect release characteristics, which would increase the risk of serious injury while skiing. Therefore, skiers are warned not to use this product with any ski boots other than those meeting the standards indicated above. Skiers are advised to consult the dealer where this product was purchased, or an equipment specialist at any SALOMON authorized ski dealer of this product, for further information regarding which ski boots meet the standards listed above.

BINDING

WARDEN MNC 11 DEMO BINDING. . . . . . . WARDEN MNC 11 BINDING.. . . . . . . . . . WARDEN MNC 13 DEMO BINDING. . . . . . . WARDEN MNC 13 BINDING. . . . . . . . . . GUARDIAN MNC BINDING - BACKCOUNTRY.. S LAB SHIFT MNC 10 & 13 BINDING. . . . . .

TECHNICAL MANUAL ALPINE 2020/21

ISO 9523

WTR

ISO 5355

71 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

WARDEN MNC 11 DEMO BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

BINDINGS INTENDED TO BE USED ONLY WITH ALPINE BOOTS COMPLIANT WITH ISO 5355 STANDARD, TOURING BOOTS COMPLIANT WITH ISO 9523 STANDARD, SKI BOOTS EQUIPPED WITH “WTR TECHNOLOGY” PADS OR WITH “GRIPWALK” PADS

WTR

ISO 5355

ISO 9523

SOLE LENGTH ADJUSTMENT

262mm – 382mm

MOUNTING & ADJUSTING 1. F or mounting Warden 11 MNC DEMO binding on skis, holes have to be drilled with the Salomon mounting jig (ref 39109101) to ensure a proper alignment of the binding. Mount the front and the rear plate on ski by tightening the screws at 4 N.m ▼

BINDING

TECHNICAL MANUAL ALPINE 2020/21

>>> summary <<<

MODEL - SPECIFIC INSTRUCTIONS >>>

WARDEN MNC 11 DEMO BINDING

2. Insert the heel and brake piece from the back and position on the plate according to the boot sole length. ▼

7. Adjust the toe height with adjustment screw until to create a gap of the thickness of the mounting instruction sheet between the boot sole and the binding. ▼

3. Insert the toe piece from the front and position on the plate according to the boot sole length. ▼

8. Check and adjust the forward pressure. ▼ 4. Boot sole length adjustment. ▼

BINDING CALIBRATION ON RELEASE TEST MACHINE For lateral release testing, please check that the shell of the boot does not rub against the body of the toe.

6. Select and adjust the setting release values for toe and heel pieces. ▼

No space between the shell of the boot and the body of the toe

Space between the shell of the boot and the body of the toe

BINDING

5. Step in the boot. ▼

TECHNICAL MANUAL ALPINE 2020/21

9. In case of adjustment with touring boots compliant with ISO 9523 standard, paste sticker on each skis. ▼

73 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

WARDEN MNC 11 BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

ISO 5355

ISO 9523

MOUNTING & ADJUSTING 1. For mounting Warden MNC 11 binding on skis, holes have to be drilled with the Salomon mounting jig (ref 39109101) to ensure a proper alignment of the binding. Mount the toe piece and the rear plate on ski by tightening the screws at 4 N.m ▼

BINDING

TECHNICAL MANUAL ALPINE 2020/21

>>> summary <<<

MODEL - SPECIFIC INSTRUCTIONS >>>

WARDEN MNC 11 BINDING

BINDING CALIBRATION ON RELEASE TEST MACHINE

2. Insert the heel and brake piece from the back position on the plate according to the boot sole length. ▼

For lateral release testing, please check that the shell of the boot does not rub against the body of the toe.

3. Step in the boot. ▼

No space between the shell of the boot and the body of the toe

Space between the shell of the boot and the body of the toe

4. Select and adjust the setting release values for toe and heel pieces. ▼

6. Check and adjust the forward pressure. ▼

BINDING

7. In case of adjustment with touring boots compliant with ISO 9523 standard, paste sticker on each skis. ▼

TECHNICAL MANUAL ALPINE 2020/21

5. Adjust the toe height with adjustment screw until to create a gap of the thickness of the mounting instruction sheet between the boot sole and the binding. ▼

75 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

WARDEN MNC 13 DEMO BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WTR

ISO 5355

ISO 9523

WARNING

SOLE LENGTH ADJUSTMENT

262mm – 382mm

MOUNTING & ADJUSTING 1. F or mounting Warden 13 MNC DEMO binding on skis, holes have to be drilled with the Salomon mounting jig (ref 39109101) to ensure a proper alignment of the binding. Mount the toe piece and the rear plate on ski by tightening the screws at 4 N.m. ▼

2. Assemble the ski brake with the heel piece. ▼

BINDING

TECHNICAL MANUAL ALPINE 2020/21

THESE ALPINE BINDINGS ARE INTENDED TO BE USED ONLY WITH THE FOLLOWING SKI BOOTS: > Alpine ski boots compliant with ISO 5355 standard. > Touring boots compliant with ISO 9523 standard > Ski boots equipped with “WTR technology” pads or with “GRIPWALK” pads

76 summary <<<

>>>

MODEL - SPECIFIC INSTRUCTIONS >>>

WARDEN MNC 13 DEMO

3. Insert the heel and brake piece from the back and position on the plate according to the boot sole length. ▼

8. Check and adjust the forward pressure. ▼

4. Insert the toe piece from the front and position on the plate according to the boot sole length. ▼

9. Select and adjust the setting release values for toe and heel pieces. ▼ 5. Boot sole length adjustment. ▼

10. In case of adjustment with touring boots compliant with ISO 9523 standard, paste sticker on each skis. ▼

BINDING CALIBRATION ON RELEASE TEST MACHINE For lateral release testing, please check that the shell of the boot does not rub against the body of the toe.

7. Adjust the toe height with adjustment screw until to create a gap of the thickness of the mounting instruction sheet between the boot sole and the binding. ▼

Space between the shell of the boot and the body of the toe

BINDING

No space between the shell of the boot and the body of the toe

TECHNICAL MANUAL ALPINE 2020/21

6. Step in the boot. ▼

77 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

WARDEN MNC 13 BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WTR

ISO 5355

ISO 9523

WARNING

MOUNTING & ADJUSTING PROCEDURE 1. Use the Salomon mounting jig (ref 3298160001) to ensure a proper alignment of the binding. Drill the skis following the ski and binding manufacturer’s instructions. Mount the toe piece and the rear plate on the ski by tightening the screws at 4 N.m (check if rear plate is correctly mounted).

BINDING

TECHNICAL MANUAL ALPINE 2020/21

78 summary <<<

>>>

MODEL - SPECIFIC INSTRUCTIONS >>>

WARDEN MNC 13 BINDING

2. Assemble the ski brake with the heel piece

3. From the center of ski, insert the heel piece on the rear plate and adjust at the “mid” position with screwdriver.

4 Step in the ski boot in the binding. Check and adjust the forward pressure.

7. In case of adjustment with touring boots compliant with ISO 9523 standard, paste sticker on each ski.

BINDING CALIBRATION ON RELEASE TEST MACHINE For lateral release testing, please check that the shell of the boot does not rub against the body of the toe.

No space between the shell of the boot and the body of the toe

Space between the shell of the boot and the body of the toe

TECHNICAL MANUAL ALPINE 2020/21

6.Adjust the toe height with adjustment screw until to create a gap of the thickness of the mounting instruction sheet between the boot sole and the binding.

BINDING

5. Select and adjust the setting release values for toe and heel pieces.

79 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

GUARDIAN MNC BINDING (BACKCOUNTRY) TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WTR

ISO 5355

MOUNTING & ADJUSTING PROCEDURE

3. Remove shaft and screw from plastic bag

▼

2. Mount the toe base plate and the step-in by tightening the screws at 4 N.m

4. Insert the toe piece in the base plate

▼

1. For mounting Backcountry bindings, holes have to be drilled with the Salomon mounting jig (ref 3267050001) to ensure a proper alignment of the binding.

5. Insert the shaft and the screw and tighten with a screwdriver (Torx T25 (x2) ) - Maxi 4 N.m

BINDING

TECHNICAL MANUAL ALPINE 2020/21

>>>

80 summary <<<

MODEL - SPECIFIC INSTRUCTIONS >>>

GUARDIAN MNC BINDING (BACKCOUNTRY)

6. Placing ski brake > Refer to the Salomon spare part catalogue to know which brake to use according to the different ski widths and binding models. ■ (fig. 1) Take the ski brake (A), insert the two lugs and assemble the ski brake on the heel piece (B) ■ (fig. 2) From the front, slide backward (A) the complete heel piece and readjust the heel piece’s position (B).

■ (fig. 3) Turn the screw (A) and remove forward the heel piece from the rear plate (B)

TECHNICAL MANUAL ALPINE 2020/21

8. Step in the boot and adjust the heel piece’s position with a screwdriver and check forward pressure

▼

7. Press the heel to lock in the step-in

9. Adjust the boot toe’s height by turning the adjustment screw to create a gap of the thickness of the mounting instruction sheet between the boot sole and the binding

BINDING

10. In case of adjustment with touring boots compliant with ISO 9523 standard, paste sticker on each ski

>>> summary <<<

MODEL - SPECIFIC INSTRUCTIONS >>>

GUARDIAN MNC BINDING (BACKCOUNTRY)

HIKING MODE SWITCH FROM SKIING TO HIKING POSITION 1 - Use the ski pole to push backward the step in, lift the ski boot, and flip forward the hiking aid.

2 - Hiking aid can be set in 2 positions : A. High position

B. Low position

SWITCHING FROM HIKING TO SKIING POSITION

2 - Push back the climbing aid and lock down the binding heel piece

3 - Before skiing check that the binding is correctly locked in

BINDING

TECHNICAL MANUAL ALPINE 2020/21

1 - The binding must be cleaned from snow, ice and dirt. DO NOT put the hand between the ski and the binding when switching to skiing position

>>>

82 summary <<<

MODEL - SPECIFIC INSTRUCTIONS >>>

GUARDIAN MNC BINDING (BACKCOUNTRY)

CRAMPON BACKCOUNTRY Use the crampon which is adapted to the ski waist width.

1 - Push backward the step in, lift the binding, and flip forward the hiking aid

2 - Insert the crampon in the two lugs of the toe piece and lock the crampon

No space between the shell of the boot and the body of the toe

Space between the shell of the boot and the body of the toe

BINDING

BINDING CALIBRATION ON RELEASE TEST MACHINE For lateral release testing, please check that the shell of the boot does not rub against the body of the toe.

TECHNICAL MANUAL ALPINE 2020/21

3 - B efore using crampons make sure that the hiking aid is in the low position. NEVER USING CRAMPONS IN THE HIGH POSITION

83 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

S LAB SHIFT MNC 10 & 13 BINDING TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WTR

ISO 5355

ISO 9523

MOUNTING & ADJUSTING PROCEDURE 1. For mounting S Lab Shift MNC 10 & 13 binding on skis, holes have to be drilled with the Salomon mounting jig (ref 39894701) to ensure a proper alignment of the binding.

Mount the toe piece and the rear plate on ski by tightening the screws at 4 N.m.

BINDING

TECHNICAL MANUAL ALPINE 2020/21

>>> summary <<<

MODEL - SPECIFIC INSTRUCTIONS >>>

S LAB SHIFT MNC 10 & 13 BINDING

5. Step-in the boot, check and adjust the forward pressure.

2. Assemble the ski brake with the heel piece.

3. From the center of the ski, insert the heel and brake piece on rear plate and aligned the heel with the 1st graduation according to the boot sole length.

6. Adjust the toe height with adjustment screw until to create a gap of the Thickness of the mounting instruction sheet between the boot sole and the binding

TECHNICAL MANUAL ALPINE 2020/21

â&#x20AC;&#x192; 4. Mount the toe piece on ski by tightening the screws at 4 N.m. Check that the toe is correctly mounted.

BINDING

7. S elect and adjust the setting release values for toe and heel pieces.

>>> summary <<<

MODEL - SPECIFIC INSTRUCTIONS

8. Binding calibration on Montana machine a- Completely close all the boot buckles b- Take the ski with your left hand and place it down onto the bench tip facing left and with the far edge side first into the centering unit. c- For vertical and lateral release testing, use the touring strap for the heel and not the automatic metal lever. For thin skis, use additional downholder.

MAINTENANCE AND REPAIR LUBRICATION The bindings should be regularly lubricated with the Salomon grease reference L0009050001. See lubrication points on brake and heel part below:

SLIDING PEDAL REPLACEMENT In case of sliding pedal replacement, please to follow below instructions: 1. The toe is constituted of 3 components:

a. The toe

b. The crampon runner a

For toe calibration, please to be careful not to pinch your fingers between the central part (1) and the wing (2) during the release.

c. The sliding pedal

BINDING

TECHNICAL MANUAL ALPINE 2020/21

2. Take the sliding pedal in hand and lift up the rubber part (d) before inserting the crampon runner.

9. When mounting the binding make sure that you fit the enclosed stickers to the ski. Explain to the skier the different lever position for mode “WALK” and “SKI”. (To refer to the “Warning - the user guide” linked to the heel).

3. Link the sliding pedal to the toe by the back side `

In “SKI” mode, the lever must be locked in horizontal position. 4. Check that the rubber part is correctly assembled.

In “WALK” mode, the lever must be locked in vertical position.

86 summary <<<

BOOTS & BINDING COMPATIBILITIES

WTR BINDINGS ARE INTENDED TO BE USED ONLY WITH FOLLOWING SKI BOOTS:

ALPINE BOOTS COMPLIANT WITH ISO 5355 STANDARD

SKI BOOTS EQUIPPED WITH “WTR TECHNOLOGY” PADS OR WITH GRIPWALK PADS

ISO 9523

STH2 BINDING "WTR" TECHNOLOGY. . . . . . . 88

WARNING THESE ALPINE BINDINGS ARE INTENDED TO BE USED ONLY WITH THE FOLLOWING SKI BOOTS: > Alpine ski boots compliant with ISO 5355 standard > Ski boots equipped with “WTR technology” pads or with Gripwalk pads Any use with other ski boots could cause the ski-binding-boot system to be faulty and affect release characteristics, which would increase the risk of serious injury while skiing. Therefore, skiers are warned not to use this product with any ski boots other than those meeting the standards indicated above. Skiers are advised to consult the dealer where this product was purchased, or an equipment specialist at any SALOMON authorized ski dealer of this product, for further information regarding which ski boots meet the standards listed above.

>>> summary <<<

TECHNICAL MANUAL ALPINE 2020/21

✖

BINDING

WTR

ISO 5355

MODEL - SPECIFIC INSTRUCTIONS

STH2 BINDING "WTR" TECHNOLOGY TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

WARNING THESE ALPINE BINDINGS ARE INTENDED TO BE USED ONLY WITH THE FOLLOWING SKI BOOTS: • Alpine ski boots compliant with ISO 5355 standard AND • Ski boots equipped with « WTR technology” or “Gripwalk” labelled kit of walking soles. Any use with other ski boots could cause the ski-binding-boot system to be faulty and affect release characteristics, which would increase the risk of serious injury while skiing. Therefore, skiers are warned not to use this product with any ski boots other than those meeting the standards indicated above. Skiers are advised to consult the dealer where this product was purchased, or an equipment specialist at any SALOMON authorized ski dealer of this product, for further information regarding which ski boots meet the standards listed above.

ISO 5355

1 – Use the Salomon mounting jig ( ref : 32981601 ) and drill the skis following the ski and binding manufacturer’s instructions. Mount the toe piece and the rear plate on the ski by tightening the screws at 4 N.m (check if rear plate is correctly mounted ).

▼

MOUNTING & ADJUSTING PROCEDURE

X4 X4

center

BINDING

2 – Assemble the ski brake with the heel piece.

▼

TECHNICAL MANUAL ALPINE 2020/21

✖

WTR

88 summary <<<

4 N.m

ISO 9523

MODEL - SPECIFIC INSTRUCTIONS STH2 BINDING "WTR" TECHNOLOGY

3 – From the center of ski, insert the heel piece on the rear plate and adjust at the “mid” position with a screwdriver.

▼

>>>

▼

TECHNICAL MANUAL ALPINE 2020/21

7 – Adjust the toe height with the adjustment screw until to create a gap of the thickness of the mounting instruction sheet between the boot sole and the binding. ( see § : ADJUSTING – TOE HEIGHT ADJUSTMENT > page 21 ) .

BINDING

6 – With the screw on the left side of the toe piece, adjust the toe wings to come in contact with the ski boot. ( see § : ADJUSTING – WING ADJUSTMENT > page 21) .

▼

5 – Select and adjust the setting release values for toe and heel pieces.

▼

4 – Step in the ski boot in the binding, check and adjust the forward pressure.

▼

L = MID

89 summary <<<

BOOTS & BINDING COMPATIBILITIES

TOURING BINDING

MTN PURE & MTN TOUR BINDING. . . . . . . . 91

WARNING These bindings do not comply with DIN/ISO 13992. The bindings have been designed, developed and produced to be used for extreme alpine skiing or ski racing. There is no fine tuning of the release settings; they are designed to release when subjected to twisting and forward lean. These bindings must only be used in conjunction with ski touring boots which have inserts for the bindings. These bindings are not compatible with bellowed ski boots such as Scarpa F1/F3/Tx. The effectiveness of the release mechanism of the bindings is highly dependent on insert and boot wear.

BINDING

TECHNICAL MANUAL ALPINE 2020/21

NOT COMPLIANT WITH DIN/ISO 13992 STANDARD AND NOT TUV CERTIFIED

90 summary <<<

MODEL - SPECIFIC INSTRUCTIONS

MTN PURE & MTN TOUR BINDING

TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY.

(Option : heel piece with brake)

WARNING

These bindings do not comply with DIN/ISO 13992. The bindings have been designed, developed and produced to be used for extreme alpine skiing or ski racing. There is no fine tuning of the release settings; they are designed to release when subjected to twisting and forward lean. These bindings must only be used in conjunction with ski touring boots which have inserts for the bindings. These bindings are not compatible with bellowed ski boots such as Scarpa F1/F3/Tx. The effectiveness of the release mechanism of the bindings is highly dependent on insert and boot wear.

B- The heel piece A- The toe piece 1- Lever for clamping and freeing 5- Retaining U-spring for the heel insert the boot 6- Boot size adjustment screw 2- Boot toe guide 7- L ow heel lift guide 3- Wings 8- Medium and high heel lift guide 4- Crampon mount 9- Length adjustment scale

C- Toe of the boot 10- Front insert D- Heel of the boot 11-Rear insert

summary <<<

18- Additional part for Dynafit / E- Optional accessories ATK crampons 12- Safety strap 13- Different types of U-spring 14- Brake 15- Clamping lever 16- Pre-fitted screw 17- Guiding tool / setting tool

>>>

BINDING

TECHNICAL MANUAL ALPINE 2020/21

BINDING DESCRIPTION

MODEL - SPECIFIC INSTRUCTIONS >>>

MTN PURE & MTN TOUR BINDING

MOUNTING & ADJUSTING PROCEDURE 1. In order to mount the bindings, it is important to use the correct Salomon jig (ref L3816250001) to ensure the binding is perfectly aligned. Put the boots on the jig and adjust the jig at boot length (the rear insert of the boot must be in contact with the jig). (fig. 1a)

Option If the brake is added afterwards, unscrew the 8 screws and put them to one side. Take off the toe and the heel pieces. Using the proper tool (n°17), line up the jig with a bushing on one of the screw holes in the heel. The three other holes should then appear under the other drill guide rings. Drill the extra hole for the brake. (fig. 1b)

Options (fig. 2b) A- Unclip the low lift guide (n°7) B- Clip the boot heel over the brake C- Tighten the pre-fitted screw by hang, 4 Nm max (n°16) D- Mount the entire sub-assembly of heel piece and brake at the top then move it backwards in the direction of the arrows Ensure the sub-assembly of heel piece and brake is properly mounted on the ski.

BINDING

TECHNICAL MANUAL ALPINE 2020/21

2. Mount the toe piece by gently screwing the screws in the order shown after so that the toe piece is still able to rotate slightly. (fig. 2a)

>>> summary <<<

MODEL - SPECIFIC INSTRUCTIONS >>>

MTN PURE & MTN TOUR BINDING

3. Mount the heel piece by tightening the screws in the order 1 - 2 - 3 - 4 (fig. 3) 4. Step-in the ski boot into the toe piece and make sure that the rear insert of the boot is correctly aligned with the U-spring of the heel piece. (making a “V” between the heel boot insert and the U-spring) (fig. 4) 5. Then fully tighten the two front screws on the toe piece (screw n°1 and 3) to the correct torque (fig.5)

6. Tilt the boot forward and fully tighten the two rear screws (screw n° 2&4) to the correct torque. (fig. 6) Check that all the screws are firmly seated and none of the thread is stripped.

7. Put the boot into the heel piece and check the length of the binding marries correctly with the boot using the snap hook of the safety strap or the designated tool n°17 as template. (fig. 7a)

8. The heel piece retaining U-spring (fig. 8) The choice of U-spring should be based up on discussions between the skier and the authorized reseller so that all factors which affect the choices are fully considered. U-springs for MEN are delivered premounted on the bindings

Model of U-spring used Skier classification

W = WOMEN

MEN

EXP = EXPERT

Type 1 or 2

Type 3

Increases release value of the binding in the event of a fall

Reduces release value of the binding in the event of a fall

For full details regarding classification of the skier, please see the Salomon technical manual > page 95 summary <<<

>>>

BINDING

Options: Assemble the safety straps onto the toe pieces (fig. 7b)

TECHNICAL MANUAL ALPINE 2020/21

MODEL - SPECIFIC INSTRUCTIONS >>>

MTN PURE & MTN TOUR BINDING

9. Once the boot is on, check that the brake arms close properly.

10. Replacing the heel piece U-spring (fig. 10)

BINDING

TECHNICAL MANUAL ALPINE 2020/21

11. Lubrication points (fig. 11)

Advise the skier to lock the brake by hand

Grease reference L0009050001

Oil reference L3968680001

11- Advice for the skier

YOU SHOULD NOTIFY THE SKIER OF THE FOLLOWING POINTS: > The bindings have been designed, developed and produced to be used for extreme skiing or ski racing. > The skier has been made fully aware of the risks involved at time of purchase of these bindings. > The leaflet attached to the heel piece should be handed to the skier. > All adjustment to the bindings (changes to the length settings and replacing the U-springs) should only be carried out by an authorized reseller > These bindings are compatible with PLUM, DYNAFIT and ATK crampons. > It is recommended to use the additional part nÂ°18, if Dynafit/ATK crampon are used > The bindings should be regularly lubricated by a certified reseller. summary <<<

RELEASE VALUE SELECTION AND ADJUSTMENT

RELEASE PREFERENCE Choosing Your Release Preference is Your Responsibility RELEASE PREFERENCE

The factors that determine the release setting on your ski bindings include your WHAT TYPE OF SKIER ARE YOU? height, weight, age, boot sole length, and your personal release preference. You are responsible for determining your own release preference based upon the chart CHOOSING YOUR RELEASE PREFERENCE IS technician YOUR RESPONSIBILITY below and for informing the ski shop of your preference. Your ski shop technician cannot thisondetermination Be sure tosole provide The factors that determine the make release setting your ski bindings includefor your you. height, weight, age, boot length, andaccurate your personal release preference. You are responsibleyour for determining your weight, own release preference based upon the chart below and for informing the ski information regarding height, age and personal release preference. shop technician of your preference. Your ski shop technician cannot make this determination for you. Be sure to provide accurate information Errorsyour may increase your risk of injury. regarding height, weight, age and personal release preference. Errors may increase your risk of injury.

SKIERS NOT CLASSIFIED AS TYPE I OR TYPE III.

TYPE

ENTRY-LEVEL SKIERS WHO ARE UNCERTAIN OF THEIR PREFERENCE

MOST SKIERS ARE SATISFIED WITH A TYPE II SETTING

SKIERS WHO DESIGNATE THEMSELVES AS A TYPE III RECEIVE HIGHER THAN AVERAGE RELEASE SETTINGS

Entry-level skiers and skiers who designate themselves as Type I receive lower than average ski binding release settings. This corresponds to easier ski binding release in a fall.

Skiers who designate themselves as Type II receive average ski binding release settings appropriate for most recreational skiing.

This corresponds to decreased risk of inadvertent binding release and increased risk of non-release. This classification is not recommended for skiers 47 lbs. (21 kg) and under.

III

If experience, you have beenyou dissatisfied withbeen the release settings that result from the your release preference, mention this to your binding Iffrom from experience, have dissatisfied with release settings that result ski shop technician.

from your release preference, mention this to your binding ski shop technician.

TECHNICAL MANUAL ALPINE 2020/21

BINDING

TYPE

95 summary <<<

RELEASE VALUE SELECTION AND ADJUSTMENT

RELEASE SETTING ADJUSTMENT

CHART 1

CHART 2

Mandatory Release values Skier's parameters

Skier's mass kg

10 to 13 14 to 17 18 to 21 22 to 25 26 to 30 31 to 35 36 to 41 42 to 48 49 to 57 58 to 66 67 to 78

≥ 95

≤ 1,48 1,49 to 1,57 1,58 to 1,66 1,67 to 1,78 1,79 to 1,94

≥ 1,95

Skier code

≤ 230 mm

231 mm to 250 mm

251 mm to 270 mm

271 mm to 290 mm

291 mm to 310 mm

311 mm to 330 mm

331 mm to 350 mm

0,75 0,75 1,25 1,5 2,0 2,5 3,0 3,5

0,75 1,0 1,5 1,75 2,25 2,75 3,0

1,25 1,5 2,0 2,5 3,0

1,5 1,75 2,25 2,75

1,75 2,0 2,5

≥ 351 mm

A B C D E F G H

5a 8 11 14 17 20 23 27 31

18 a 29 40 52 64 75 87 102 120

141

4,5

4,0

3,5

3,0

165

5,5

5,0

4,5

4,0

3,5

3,0

194

6,5

6,0

5,5

5,0

4,5

4,0

229

7,5

7,0

6,5

6,0

5,5

5,0

M N O

67 78 91 105 121 137 b

271 320 380 452 520 588 b

8,5 10,0 11,5

8,0 9,5 11,0

7,0 8,5 10,0 12,0

6,5 8,0 9,5 11,0

6,0 7,5 9,0 10,5

0,75 1,0 1,5 2,0 2,5 3,0

0,75 0,75 1,25 1,75 2,25 2,75 3,5

NOTE 1 For skiers of 13 kg and under, no further correction is appropriate. NOTE 2 For skiers of 17 kg and under skier type - 1 is inappropriate. a : Lowermost tolerance limit. - b : Uppermost tolerance limit.

BINDING

TECHNICAL MANUAL ALPINE 2020/21

79 to 94

Skier's height m

Inspection parameters Twist Forward MZ lean MY N⋅ m N⋅ m

Examples for Initial indicator value These are only the starting point in the binding setting process and may need to be modified in order to achieve the correct measured release value. Z (presetting), depending on boot sole length

96 summary <<<

RELEASE VALUE SELECTION AND ADJUSTMENT

ADJUSTMENT PROCEDURE

This classification has to be determined by a dialogue between the skier and dealer, which helps to take into account the diverse factors that influence the adjustment. These factors are explained in the norms cited above. › Type I skiers: - Ski conservatively. - Prefer slower speeds. - Ski on easy to moderate slopes. - Intermediate level, but not in good physical condition. - Good skiers, smooth and supple style, empha sizing safety. - Favor lower than average release/retention settings. This corresponds to an increased risk of inadvertent binding release in order to gain increased release capacity in a fall. › Type II skiers: - Intermediate skiers in good physical condition. - Prefer a variety of speeds. - Ski on varied terrain, including most difficult trails. - All skiers who do not meet all the descriptions of the other skier types. › Type III skiers: - Ski aggressively. - Normally ski at high speeds. - Prefer moderate to steep terrain. - Favor higher than average release/retention settings. This corresponds to decreased capability to release in a fall in order to decrease risk of inadvertent binding release. - Type 3 settings should not be used by skiers of less than 22 kg.

OTHERS SKIERS TYPE › Type I— skiers: - Skiers looking for a lower release setting than type 1. - Recommended for beginners over 25 years old. › T ype III+ skiers: - Very strong skiers, on challenging terrain. - Skiers looking for a higher release setting than type 3 skiers. Skier type does not have the same meaning as skier ability. For instance, an advanced skier who skis all-terrain, but is not particularly aggressive, may be able to use Type 2 settings.

ADJUSTMENT PROCEDURE 1. F ind the skier’s code in chart 1. Locate the skier’s weight in the first column and the skier’s height in the second column. If the skier’s weight and height are not on the same row, select the skier’s code on the highest row. 2. This skier code is appropriate for Type 1 skiers. For Type I— skiers: move up one row. For Type II skiers: move down one row towards the bottom of the chart. For Type III skiers: move down two rows on the chart. For Type III+ skiers: move down three rows on the chart. 3. For skiers who are 50 years or older, or un-der 10 years: move up one row on the chart. - For skiers weight 13 Kg and under, no further correction is appropriated. - For skiers weight 17 Kg and under, type 1- skier is inappropriated. 4. A fter having determined the skier code, locate the column in chart 2 that represents the skier’s boot sole length (in mm). 5. The box at the intersection of the skier’s boot sole length column and the skier’s code row, shows the initial indicator setting for the skier. Adjust both toe pieces and heel pieces accordingly. 6. Caution: If the box at the intersection of the skier’s boot sole length column and the skier’s code row is empty, move horizontally on the same row and use the closest indicator setting. 7. If it is obvious that the bindings release inadvertently (unnecessarily), at the request of the skier, the dealer can: - At first, increase the level in the forward fall, that is, on the heel piece. - Then, only if the inadvertent releases persist, increase the level in torsion, that is, on the toe piece. Proceed very progress ively in stages of half-points.

TECHNICAL MANUAL ALPINE 2020/21

SKIER CLASSIFICATION

BINDING

The release setting adjustment is obtained by using the adjustment cap or adjustment screws. The release setting is visible on the indicator. Adjust the toe piece and heel piece to the same settings. It is highly recommended to use a measuring device to check the release torque (see ISO 11088). Release value selection and adjustment The release settings must be used by the tech nician to determine the appropriate adjustment for each skier, which conforms to the following norms: ISO 11088, ASTM F 939, ASTM F 1063, and AFNOR FD S 52-448 (documentation fascicle).

>>> summary <<<

FINAL CHECKING AND VISUAL INSPECTION

A Salomon certified technician must sign or initial the Workshop form indicating that all systems inspections have been performed. A final check is your quality control measure to verify that all required procedures have been properly completed and involves the following steps: 1. Visual inspection of system components. 2. Test for elastic travel and return. 3. Release value within specified range and boot-binding compatibility.

VISUAL INSPECTION OF SYSTEM COMPONENTS TROUBLESHOOTING PROCEDURE

BINDING

TECHNICAL MANUAL ALPINE 2020/21

After the bindings have been properly mounted and adjusted, visually inspect the ski/boot/ binding system. › T he boot: Check: - for gross irregularities where the boot contacts the binding and the AFD (deformation, wear,...), - that the boot conforms to the norm (DIN, ISO or ASTM markings). If the boots are not marked, check with the supplier. These bindings are not designed to function with boots that do not conform to the norm. - that the boot has not started to crack or break. The boot toe Check for the absence of: - rubber and/or metal tip protectors - mold flashings - a ramp or bevel in front of the AFD area - grid pattern or tread in the AFD area - excessive wear - a toe sole extension with corner radius of less than 7 mm - asymmetrical shape of the toe sole. The boot heel Check for: - debris lodged in the sole - scraped or improperly canted boot sole - cut-outs in the heel sole that catch on the entry pedal - cut-outs in the sole that impede proper brake function. Note: If you are uncertain of boot compa tibility, perform the ‘Clean vs Lubricated’ test. Boots that fail this test or violate any of the above points should not be used with any Salomon binding.

› T he ski: Check for: - mounting screws protruding through the base - delaminated sidewall. This can be detected by running your fingers along the sides of the ski. - base plate flush with ski surface - delaminated topskin - pre-drilled holes. Bindings shoul d not be installed on skis that have already been drilled for three or more sets of bindings. › T he binding: The toe piece Check for: - stripped, loose or missing screws - condition and location of the AFD (ripped, loose, imbedded dirt, boot sole pattern, tread imprint, etc) - condition of anti-friction inserts (where applicable) - missing or unreadable adjustment indicators and missing windows - bent or broken base plate, principal axis or housing - stripped or jammed toe height and cup adjustment screws - jammed release adjustment - other visible wear.

The ski brake Check for: - improper installation - broken entry pedals - bent brakearms - strength of ski brake A brake must not compress totally when the ski is set on a flat surface. - other visible wear - proper position of brakes They shouldn’t touch the ski while they are functioning (especially on fat skis). The complete system Place the boot in the binding and check the accuracy of: - toe height adjustment (if applicable) - toe cup width adjustment (if applicable) - forward pressure adjustment - release adjustment settings - symmetrical mounting of bindings to ski center line (+/- 1 mm) This should be in the same location on both skis. If you discover a correctable problem, repair the problem and re-test. If the system still falls outside the “in-Use range”, perform the ‘Clean vs Lubricated’ test.

The heel piece Check for: - stripped, loose or missing screws - improperly installed brake - defective heel track - bent or broken base plate, track or heel guide - missing Delrin inserts in the heel guide - jammed release adjustment - unreadable indicators - other visible wear.

TEST FOR ELASTIC TRAVEL AND RETURN › L aterally: Secure the ski. Hit the forefoot area of the boot with a rubber hammer. Use sufficient force to move the boot off-center, but not hard enough to release the system. The boot should move off-center at least 5 mm and return to center within 2 mm of its original position.

›V ertically: Put the boot in the binding, depress the heel lever while pulling forward on the upper cuff of the boot until the boot heel lifts at least 5 mm. Release both hands simultaneously. The boot should go back in place quickly and smoothly. This check can be performed either manually or by using a mechanical device. If a measuring device is used, follow the recommendations of the test device manufacturer for proper procedure.

98 summary <<<

MECHANICAL INSPECTION

RELEASE VALUE WITHIN SPECIFIED RANGE AND BOOT/BINDING COMPATIBILITY › T roubleshooting: Boot/binding systems wear with time. Mechanical inspection allows you to identify when the ski/boot/binding system is not working as it was originally intended. Readjustment of the binding is not a sign of malfunction, but can be a sign of normal wear. › T est for lateral travel - failure: Re-check all binding-to-boot adjustments. Re-inspect the boot and the binding according to the Visual Inspection criteria. If the boot is dirty, clean the sole with a solution of soap and water. If the binding is dirty, clean it according to the procedures described in this chapter under ‘Maintenance’. Re-test the system for elastic travel and return.

› T est the toe: First, exercise the toe by releasing it once in each direction. Then, using test device, measure and record the twist release value in each direction. The measured release value should be considered to be the middle quantitative value of three measured releases. If the first two measured values are the same, there is no need to take a third measurement. See examples of middle quantitative values (Chart. 1). The toe passes this inspection if the middle quantitative values in both directions fall within the ‘Inspection range’. See sample “System inspection ranges” (Chart. 2). Symmetry test note You should be aware of the possibility of an asymmetric release. If your tested values for clockwise and counter-clockwise release appear to be at opposite extremes of the inspection range, you may have an installation error or incompatible boot. Troubleshoot the system and re-test after the problem has been corrected. › T est the heel: First, exercise the heel by releasing it once. Using a test device, measure and record the heel release value. The middle quantitative value of three heel releases should fall within the +/- 15% “inspection range”. ›R elease value verification - failure: When the technician is satisfied that all required procedures have been completed according to Salomon’s recommendations in this manual, he or she must sign the Workshop Form. (The signing technician must currently be certified by Salomon.) Note: During manufacturing, Salomon precision tests every binding up to 5 times to assure that it functions properly and is calibrated correctly. It is extremely rare that a new component would be out of calibration unless there is damage.

CHART. 1 Three release values

Middle quantitative value

45 - 40 - 50

60 - 50 - 50

30 - 40 - 50

55 - 65 - 60

CHART. 2 - SYSTEM INSPECTION RANGES 43 Readjustment Tolerance range

50 58 67

Inspection Tolerance range

TECHNICAL MANUAL ALPINE 2020/21

Testing of release values with a test device is recommended (fig. 1). If a test device is not used, the skier should be informed. In addition, the skier must be warned about the risk of possible breakage of boots and bindings that have been subjected to shocks or abnormal stress.

BINDING

› T est for vertical elastic travel - failure: Clean the boot sole of any snow, dirt or debris. Check for excessive wear at the boot heel. Repair or replace any non-DIN boot. Check that the boot enters the binding correctly. Align the boot with toe and heel cups and re-insert the boot. Check the release setting. It should not exceed the minimum or maximum visual indicator setting and should be set appropriately for the skier. If the measured +/- Mz and My values are located outside of the +/- 15% inspection range, consult the manufacturer’s instructions for procedures concerning malfunctions. If after this procedure, the measured values are within the readjustment range of +/-30%, the binding can be readjusted. These readjustments should allow you to obtain measured values as close as possible to the selected individual release torque within the +/- 15% range. If the release is still outside the +/- 30% readjustment range after having followed the procedures for malfunctions, do not readjust the binding unless it is specifically authorized by the manufacturer (chart. 1).

99 summary <<<

MECHANICAL INSPECTION

BOOT/BINDING COMPATIBILITY DIAGNOSIS

Lubrification test

Clean vs lubricated test

400

100

360

320

280

240

200

160

120

FAIL

PASS

40 0

Torsion (Nm)

FAIL Forward flex (Nm)

Clean vs lubricated test 1. Determine the measured release value in the ski/ boot/binding system without lubricant. 2. Determine the measured release value in the ski/ boot/binding system after lubricating all contact points between the boot and binding with a lubricant specified by the manufacturer. If nothing particular is specified, use soap and water. 3. Calculate the ratio between the two tests by dividing the result with the lubricant by the result without it. 4. If the quotient is above 1.2 or under 0.8, the system is considered to be incompatible. If the boot test result is a satisfactory +/- 30%, but the binding does not release within the â&#x20AC;&#x2DC;readjustment toleranceâ&#x20AC;&#x2122; range, check the calibration of the adjustment machine. Have another technician redo the test. If the system still falls outside the range, the binding should not be used.

10 20

100

0 40 80 Forward flex (Nm)

120

160

200 240 Clean test

280

320

360

400

BINDING

TECHNICAL MANUAL ALPINE 2020/21

Torsion (Nm)

100 summary <<<

RETAIL - SPECIFIC INSTRUCTIONS

RETAIL SKIER INSTRUCTION AND WARNING › Explanation of entry/exit/re-entry: The proper use of the system (entry, exit and re-entry) should be explained using the skier’s own system as an example. › Explanation of backcountry instructions The transition of walking mode to skiing mode in case of backcountry binding should be explained using the skier’s own system as an example. ›R eceipt of in-box instructions and warranty: When a skier purchases a new binding, it is required that s(he) also receive the instructional pamphlet included in each binding box (1st page of the pamphlet as example below).

NOTICE À REMETTRE AU SKIEUR BEDIENUNGSANLEITUNG FÜR SKIFAHRER DENNE VEJLEDNING SKAL UDLEVERES TIL SKILØBEREN INSTRUCCIONES PARA ENTREGAR AL ESQUIADOR ΟΔΗΓΙΕΣ ΓΙΑ ΤΟΥΣ ΣΚΙΕΡ INSTRUCTIONS FOR ISSUE TO SKIERS FOGLIO INFORMATIVO DA CONSEGNARE ALLO SCIATORE HANDLEIDING VOOR DE SKIËR FOLHETO INFORMATIVO DESTINADO AO ESQUIADOR INSTRUKTIONER FÖR GER SKIDÅKAREN SUUSATAJALE MÕELDUD TEATIS A SÍELŐNEK ÁTADANDÓ ÚTMUTATÓ PAZIŅOJUMS, KAS NODODAMS SLĒPOTĀJAM SLIDININKUI SKIRTAS INFORMACINIS LAPELIS INSTRUKCJA DLA NARCIARZA NÁVOD PRO LYŽAŘE NÁVOD PRE LYŽIARA VEILEDNING SOM GIS SKIKJØREREN ИНСТРУКЦИЯ ДЛЯ ЛЫЖНИКА ИНФОРМАЦИЯ ЗА СКИОРА KAYAKÇILARA VERILECEK TALIMAT TIEDOTE HIIHTÄJILLE INSTRUCŢIUNI DE ÎNMÂNAT SCHIORULUI ПОВІДОМЛЕННЯ ДЛЯ ЛИЖНИКА

BINDING

UPUTSTVO KOJE TREBA DA SE URUCI SKIJAU

TECHNICAL MANUAL ALPINE 2020/21

In principle an adjustment report is established by the ski shop and delivered to the user. It shall at least contain the following information: - skier’s parameters, - indicator value, - measured value of Mz and My, or pass/fail result of the system test. The exact content of the report and its delivery conditions are defined by the national standard organizations 11088.

101 summary <<<

RENTAL - SPECIFIC INSTRUCTIONS

INSPECTION AID FOR APPLICATION OF ISO 13993 concerning - rental ski shop practice - sampling and inspection of complete and incomplete alpine ski-binding-boot systems in rental applications (this supplement does not replace ISO 13993). To keep your rental equipment in good condition while minimizing liability we recommend the following program (this comes out of the ISO 13993 standard).

RENTAL INSPECTION SUMMARY Since it is impractical to perform a full inspection each time a system is rented, a routine of preseason and inseason inspections has been developed to verify release indicator accuracy, confirm correct equipment function, and assure proper assembly and adjustment procedures by the rental shop staff. Fully implemented, the procedures that follow provide rental shop customers a standard of care equivalent to that provided retail shop customers under current ISO and ASTM standards.

PRESEASON INSPECTION PRESEASON INSPECTIONS ARE PERFORMED ON COMPONENTS OF THE RELEASE SYSTEM: bindings and boots. All rental bindings, new and used, are visually inspected, and then tested using specially selected Reference Boots. Bindings that fail go through a troubleshooting procedure to identify and correct the deviation or malfunction. If this procedure does not correct the problem, the binding is removed from inventory. All rental boots, new and used, are visually inspected for damage, wear, contamination, broken or missing parts, or inferior materials at contact points with the binding.

BINDING

TECHNICAL MANUAL ALPINE 2020/21

NEW manufacturer pre-mounted* or NEW sealed system bindings**

102

*a combination of new skis and new bindings provided by the original equipment manufacturer that is ready to be fitted to boots BINDINGS

BOOTS

All USED bindings or NEW but not pre-mounted bindings and plates

Note 3. A visual inspection for compatibility and interchangeability shall be performed on all boots in accordance with procedures recommended in this technical manual. Note 4. As a check on boots in the rental inventory, a single system sample, by make, model and size, shall be taken and tested in accordance with the paragraph «inseason sampling and inspection» If a boot generates a deviation other than the accepted inspection tolerance , all boots in the category shall be visually inspected and as a check, a 16 system (or less if 16 systems are not available) random sample shall be taken and tested. If any boot in this sample generates a deviation other than the inspection tolerance , all remaining boots in the category shall be tested. Note 5. As a check on boots that have been accepted into the rental inventory in a prior season, a 5 % (not less than 16 nor more than 80 systems) sample shall be taken and tested. If a boot generates a deviation other than the accepted inspection tolerance, then all boots in that make, model or age category shall be visually inspected and tested. All remaining boots in the rental inventory shall also be visually inspected. If the reason for the deviation is found in another boot category, all boots in that category shall also be tested.

INSEASON INSPECTION

**protected from damage by the original packaging of the manufacturer during transportation The sample of bindings shall be tested with a reference boot according to "Note 1". Reduced sample size according to "Note 2".

Inspection according to "Note 1".

NEW

USED

Inspection according to "Note 3" and "Note 4".

Note 1. Bindings used in an interchangeable rental programme shall be inspected for appropriate function (see «Preseasonal Binding Inspection») and valid release indicators in accordance with clause «Preseasonal Boot Preparation and Inspection» Note 2. The sample size shall be ≥ 5 % of the rental inventory (see Table B) but at least 16 systems (equipment for seasonal rental is not included). If the rental inventory is less than 16 systems, the sample size is complete when the entire rental inventory has been inspected. If the rental inventory is more than 1 600 systems, the sample size shall not be more than 80 systems.

Inseason inspections are performed on complete rental systems to ensure that the equipment is adjusted appropriately and continues to function correctly. Typically 5% of the rental inventory is tested during each two weeks sampling period. The random sample is equally divided between equipment that is available for rental and equipment that has just been rented. The equipment in the ‘as rented’ category is from real skiers in the condition in which it is either dispatched or returned, while the ‘available for rental’ equipment may be set up for fictitious skiers. Only single skis, not pairs, are tested, and testing at the toe is only required in one direction. A count is maintained of test results which exceed allowable limits. The magnitude and frequency of these deviations determines the frequency of future inspections. Shops which fail an inspection must sample daily until the source of the problem is found and corrected. Then, as inspection results improve, the frequency of sampling and inspection is relaxed.

summary <<<

RENTAL - SPECIFIC INSTRUCTIONS

IMPORTANT TERMS CORRECTION FACTOR

The value that must be added or subtracted from the initial visual indicator setting to bring the test result within the Inspection Tolerance (or Inspection Range).

DIRECTIONS OF RELEASE

Unless otherwise specified (see Inseason Inspection), the directions of release to be tested are forward lean and clockwise and counterclockwise in twist.

release (forward lean and both directions in twist- three releases in each direction). 5. Average the Release Torque for CW and CCW twist release. 6. Reject and replace any boot with a CW to CCW difference of more than 6 Nm for adult boots or 4 Nm when testing child boot types. 7. Rank the five twist results and select as the Reference Boot for twist, the middle boot. 8. Rank the five forward lean results and select as the Reference Boot for forward lean, the middle boot.

TEST DEVICE

A device which meets ISO standard 11110 (or ASTM standard F1061) and has been checked and maintained in the manner specified by the device manufacturer.

TEST RESULT OR RELEASE TORQUE

The middle quantitative value of three tests made in the same direction. (Add other terms from ISO 13993 or ASTM F1064 that are not defined elsewhere in the tech manual).

PRESEASON TEST REFERENCE BOOT SELECTION

The Reference Boot is a boot of a designated sole length which is otherwise typical of the boot inventory. Use the procedure below if the boot inventory includes several models and a representative boot can not be easily identified. 1. Select five single boots with sole lengths as specified in Chart A for the binding type to be tested: adult, junior, or child. 2. Clean all five boots with a mild detergent and water. 3. Adjust a rental binding to the release indicator setting specified in Chart A for the binding type. 4. Fit the binding to the boots and determine the Release Torque in all three directions of

PRESEASON BINDING INSPECTION

The procedure that follows is an integral part of preseason maintenance. It is also a good way to determine if mainte nance is adequate and which units have outlived their usefulness and must be removed from inventory. 1. Clean areas of the bindings that contact the boot and perform all preseason binding maintenance. 2. Visually or manually check: a. AFD condition. b. Brakes function. c. Release indicator readability and travel. d. Screw tightness. e. (other product specific inspections if required) 3. Fit each binding to the Reference Boot and adjust the release indicators to the value in Chart A. 4. Check that the heel track and toe track code (if any) agree with the sole length code (if any) of the Reference Boot. 5. With the Reference Boot in the binding, verify elastic travel of the toe piece by striking the boot toe with a mallet or dead hammer and checking that the toe piece returns the boot quickly and completely to center. 6. Verify elastic travel of the heel piece by lifting the boot while depressing the heel

piece cocking lever and checking that the heel piece returns the boot quickly and completely to the latched position. (other product specific procedures if required). 7. Manually release the binding 3 times in each direction. 8. Lubricate all boot/binding interfaces with a mild liquid detergent and water solution. 9. With the Ski Binding Test Device determine the Release Torque for each direction of release (forward lean and both directions in twist). 10. Record “PASS” in the binding's maintenance record if Test Results are within the Inspection Ranges provided in Chart A. 11. Set the ski aside if the Test Result in any directions of release is outside the Inspection Range in Chart A. 12. Follow Troubleshooting Procedure for units which have been set aside and retest if changes in the unit's condition or adjustment are made. 13. Record “FAIL” in the binding's maintenance record if, after troubleshooting, test results in any direction of release are outside the In-Use Range. Replace the ‘failed’ unit and retest before returning the ski to service. 14. If after troubleshooting, Test Results are outside the Inspection Range but within the In-Use Range, apply a Correction Factor to the unit and note the Correction Factor for that unit in the binding's maintenance record. 15. If many bindings fail, check the test device and re-inspect the Reference Boot. If necessary, select another boot and retest the bindings.

CHART A - PRESEASON BINDING INSPECTION Reference torque twist Nm

Reference torque forward Nm

Twist inspection range Nm

Forward inspection range Nm

Twist in-use range Nm

Forward in-use range Nm

Children

258

2,0

17-23

64-87

14-27

52-102

Junior

306

4.3

165

37-50

141-194

31-58

120-229

Adult

327

5.8

229

50-67

194-271

43-78

165-320

summary <<<

BINDING

Skier Binding Sole Release code type length indicator mm setting

TECHNICAL MANUAL ALPINE 2020/21

INSPECTION PROCEDURES

>>>

103

RENTAL - SPECIFIC INSTRUCTIONS >>> INSPECTION PROCEDURES

PRESEASON BOOT PREPARATION The procedure that follows is an integral part of preseason maintenance. 1. C lean all boots with (a mild detergent and water), and repair or replace damaged or missing parts. 2. Visually check: a. Conformance with ISO and other applicable standards. If the boot contacts the binding, brake, or AFD in areas other than the designated contact points, it may be incompatible with the binding (product specific figure or description). b. Boot material. If the sole at the contact points with the binding or AFD can be scratched with a finger nail, the boot may be of inferiors quality and incompatible with the binding. c. Boot sole condition. If the boot sole is damaged, worn, or contaminated at contact points with the binding or AFD in a manner which can not be corrected, the boot may be incompatible with the binding. d. Brake compatibility with sole. e. R ubber and/or metal sole protectors. If such materials contact the binding or AFD the boot may be incompatible with the binding. f. Mold flashings. Flashing which can be seen or felt at contact points with the binding, brake, or AFD must be carefully removed. 3. Remove from inventory all boots that have failed the visual check.

Although sampling eliminates the need to test every boot before the season starts, the sample chosen must be representative of the inventory. 1. For boots that are new to inventory or have never been inspected, take a single boot from each cell (a cell is all boots of the same make, model, year, and shell size). 2. For used boots, take a 5% (but not less than 16 or more than 80) random sample of the entire inventory. Make sure that there is at least one boot from each cell in the sample.

The procedure that follows helps to assure both boot/binding compatibility and boot interchange ability. Note: when using Chart A, in the Boot Inspection procedured that follow, the Sole Length and Release Indicator Setting Columns should be ignored. 1. Randomly select a pair of bindings that have passed the preseason inspection from each binding type; adult, junior, child. 2. Lubricate all boot/binding contact points with a mild liquid detergent. 3. Without regard to whether the boot is new or used, sort the sample by sole type and length according to the 20 mm Sole Length Categories defined by binding adjustment chart (ISO 11088) . 4. In each Sole Length Category rank the boots by sole length and select the middle boot. 5. In each Sole Length Category fit the appropriate reference bindings to this “typical” boot and adjust the two bindings to release as close as practical to the Reference Torque in Chart A. Use the Reference Torque corresponding to Skier Code (L) for the Adult binding, (J) for the Junior binding, and (E) for the Child binding. 6. Rinse the lubricant from one binding and mark it “clean”. Mark the other “lubricated”. 7. Test each boot in the Sole Length Category with the clean Reference Binding and then the lubricated Reference Binding in both twist and forward lean (only one direction in twist is required for the clean binding). 8. Set aside any boots for which the lubricated Test Result is more than 20% less than the clean Test Result in the same direction of release or the lubricated Test Result in any direction of release is outside of the Inspection Range provided in Chart A for the Skier Code used to set up the Reference Binding (L, J, or E). 9. Repeat the Visual Check on all boots that have been set aside, correct any defects noted, and retest. Remove from inventory boots that fail the retest. 10. Check all other boots from the same cell (make, model, year, and shell size) as those that failed. Note: On completion of the preseason inspection, clean the liquid detergent from the equipment (and lubricate the binding before returning it to service).

BINDING

TECHNICAL MANUAL ALPINE 2020/21

PRESEASON BOOT SAMPLING

PRESEASON BOOT INSPECTION

104 summary <<<

RENTAL - SPECIFIC INSTRUCTIONS

INSEASON SAMPLING AND INSPECTION The Inseason Inspection is a test of complete systems and all the procedures used by the rental staff to assemble and adjust the system.

The program uses random samples of rental inventory taken at routine intervals. Any sampling program that gives every unit of

inventory the same chance as every other of being picked is valid.

SAMPLE FREQUENCY

5. If the results are within the Inspection Range, the unit passes. 6. If the results are outside Inspection Range but within the In-Use Range, count the unit as a Class I Deviation. 7. If the results are outside the In-Use Range, count the unit as a Class II Deviation. 8. Check elastic travel and visually inspect the ski brake function, interface areas between boot and binding, including AFD, lug height adjustment (if appropriate), and forward pressure. Count any deficiencies as Class I Deviations.

9. If more than the maximum number of Class I Deviations given in Chart B are found in the sample, or a single Class II Deviation is detected the sample fails and daily sampling must be conducted until the problem which led to the failed sample is found and corrected. For Troubleshooting Procedures following a Failed Inseason Inspection. 10. Record the date the sample was tested, the number of units tested the number of Class I and Class II (or III) Deviations, whether the sample passed or failed and any actions taken. There is no need to record the identity of units tested or actual Test Results.

Random sampling is conducted throughout the entire season. Frequency is as follows: 1. After 7 days of operation. 2. If the sample passes the next sampling is taken after another 7 days of operation. 3. If two consecutive samples pass, sampling frequency is increased to 14 days. 4. If a sample fails at any time, daily sampling is instituted until two consecutive samples pass, at which point weekly sampling resumes.

SAMPLE SIZE Sample size is 5% of inventory but not less than 16 nor more than 80 units as noted in Chart B. Sample size is based on average daily output. If rental output drops below 50% of capacity over the sampling period, the sample size can be reduced proportionately.

CHART B - SAMPLE SIZE

Inventory Size

100

200

300

400

500

600

700

800

900

Sample Size Units

Maximum Class I Dev.

1. Take a random sample of the rental inventory as determined by Chart B. Take half the sample from inventory as it is either rented or returned and the remainder from inventory available for rental . 2. Wipe the boot clean and cycle the boot/ binding systems at least once in each direction. 3. Test sample units in Twist (one direction only) and Forward Lean. 4. Compare the Test Results with the Inspection Range for the appropriate Skier Code.

RENTAL SKIER INSTRUCTION AND WARNING It shall at least contain the following information: - skier’s parameters, - indicator value, - measured value of Mz and My, or pass/fail result of the system test. The exact content of the report and its delivery conditions are defined by the national standard organizations 11088.

Explanation of entry/exit/re-entry: The proper use of the system (entry, exit and re-entry) should be explained using the skier’s own system as an example. › E xplanation of specific instructions It is required that the dealer explains to the skier, specific instructions included in the instructional pamphlet (ex: transition of walking mode to skiing mode in case of backcountry binding…).

BINDING

In principle an adjustment report is established by the ski shop and delivered to the user.

TECHNICAL MANUAL ALPINE 2020/21

INSEASON INSPECTION

105 summary <<<

MAINTENANCE AND REPAIR

RETAIL GUIDELINES Salomon bindings require a minimum of maintenance to enhance performance and their useful life. They should be cleaned, inspected and lubricated prior to each season and every 15-20 skier days per season as follows: Inspect all components of each set for damage or excessive wear.

●

Repair or replace damaged or excessively worn parts and/or components.

Apply Salomon grease to the lubrication points indicated for each model. Do not use silicone or penetrating oils unless the lubricant is specifically approved.

●

Clean the exposed areas of the components with a cloth or rag. Wipe any dirt or grit from the binding housings, heel track and the region under the heel cup. Do not use solvents or hot water or high pressure liquid cleaning systems to clean bindings. Solvents may cause permanent damage to the plastic structure by dangerously modifying the product technical characteristics. The markings can also be erased.

●

Recommend to the skier that routine maintenance and inspections be performed by an Authorized Dealer. This will help ensure that any problem that may develop with the system can be detected and corrected by a trained technician.

RENTAL GUIDELINES Proper maintenance of rental systems includes a complete inspection of the entire rental inventory prior to the ski season. Bindings should be cleaned, inspected and lubricated in the following manner: Inspect all components for damage or excessive wear. Repair or replace damaged or excessively worn parts and/ or components.

●

Remove the toe by sliding it off the front plate.

●

RENTAL POST SEASON STORAGE To prepare rental equipment for summer storage: All binding visual indicator adjustments should be reduced to the lowest setting. Do not attempt to adjust the release setting below the lowest setting as damage may result.

●

Visually or manually check, the pedal, the locker working and screw tightness.

●

Remove the heel by sliding the housing off the rear of the track.

The binding heels should be stored in the closed position.

●

BINDING

TECHNICAL MANUAL ALPINE 2020/21

●

Visually or manually check, brakes function, locker working, screw tightness.

The equipment should be stored in a cool, dry and ventilated area away from direct sunlight.

●

Clean the exposed areas of the components with a cloth or rag. Wipe any dirt or grit from the binding housings, heel track and the region under the heel cup. Do not use solvents, hot water or high pressure liquid cleaning systems to clean bindings. Solvent may cause permanent damage to the plastic structure by dangerously modifying the product technical characteristics. The markings can also be erased.

●

Apply Salomon grease to the lubrication points indicated for the appropriate model. Do not use silicone or penetrating oils unless the lubricant is specifically approved.

●

Slide the heel back on the track.

●

The brake is removable to facilitate ski maintenance.

●

This should be followed by periodic in-season inspections and when a binding looks particularly dirty or if visual inspection reveals that something may be wrong. This helps to ensure that all components are functioning correctly.

●

Never attempt to interchange any SR, SC or retail toe baseplates or heel tracks with other model baseplates or heel tracks.

106 summary <<<

MAINTENANCE AND REPAIR

BROKEN MOUNTING SCREW Salomon screw extractor kit: it comes with two bits of different lengths. The longer bit is for use with the Salomon jigs for adult skis. The shorter bit should be used with the Salomon jigs for junior skis. The procedures for using both bits are the same. When a screw or tap breaks in a ski, it must be removed carefully to avoid further damage.

Follow this procedure: 1. Fit the extractor drill bit into the electric drill with the shoulder touching the chuck. 2. Fasten the appropriate jig onto the ski. 3. Position the correct jig bushing directly over the broken screw. 4. Drill slowly around the broken screw using an up-and-down movement to let the shavings escape. Caution: do not hit the screw. 5. Continue until the chuck touches the bushing of the jig.

6. The broken screw will come out inside the extractor bit. 7. Remove the screw using a pair of pliers. 8. Turn the ski over and tap lightly to remove all shavings. 9. Put a drop of glue into the hole. 10. Insert a plug from the kit using a hammer. 11. Insert binding screw and tighten using a hand driver. Do not over tighten. 12. W hen a hole simply needs to be widened to accept the plastic plugs, use an 8 mm diameter bit. Do not drill deeper than 10 mm.

STRIPPED SCREWS For a stripped screw, use the repair kit L0008780001. For this operation, use the corresponding jig and position it properly by lining it up with the hole to be repaired.

When drilling, the drill bit must be perpendicular to the surface of the ski.

Make sure you donâ&#x20AC;&#x2122;t go beyond the plug once it is in place. You can file it down to make it level with the surface.

JUNIOR C 5, L 7-10, LITHIUM 10, C5 GW, L6 GW, L7 GW, L10 GW ANTI FRICTION PLATE REPLACEMENT 1. I nsert a screwdriver width 6-8 mm at the front of the plate (fig. 1). 2. M ove over the screwdriver to eject the plate (fig. 2). 3. Place the new plate and hand clip it (fig. 3 & 4).

1 5

BINDING

TECHNICAL MANUAL ALPINE 2020/21

Caution: for models with elastic pedal (range 08), check the presence of the elastic block under the pedal (fig. 5).

107 summary <<<

TRACEABILITY

TRACEABILITY INFORMATION ON BINDINGS IN CASE OF WARRANTY, THE TRACEABILITY CODE OF THE PRODUCT IS REQUIRED.

WHERE TO FIND THE INFORMATION? A- ON THE LABEL OF THE BINDING BOX - First numbers: Production year (example 18 for year 2018) - S econd numbers: Printing label day (example: 267th day of the year 2018)

B- DIRECTLY ON THE PRODUCT Each binding is divided in three subassemblies. Each subassembly has traceability code.

General location: - On the Toe : in front between the two wings, 3 or 2 digits (A9 is an example)

Heel subassembly

- On the heel: On the base below the cuff, 3 or 2 digits (A9 is an example)

Toe subassembly

- On the brake, 3 or 2 digits (A9 is an example)

Brake subassembly

Exception:

TECHNICAL MANUAL ALPINE 2020/21

TOE GUARDIAN MNC 16&13

MTN

C5, C5 GW & L6 GW

MTN

C5, C5 GW, L6 GW

MTN

X12 TO X16

X18 TO X20

X12 TO X16

X18 TO X20

HEEL

BRAKE

BINDING

LITHIUM 10 • MERCURY 10&11 • Z10 GW & Z11 GW • L10 GW - M10 & M11 GW

108 summary <<<

BOOT

summary <<<

NORM AND COMPATIBILITY THERE ARE DIFFERENT STANDARDS : ISO 5355 AND TOURING 9523 The Alpine boot soles are standardized and bindings are designed accordingly. The standard norm concerns not only the shape and dimensions as illustrated, but also the friction coefficient of the area of the sole which is in contact with the anti-friction plate on the binding. In practical terms: The boot manufacturers who display one of the following markings: DIN, ISO, ÖN, UNI guarantee that they use standard norms. In the absence of any of these, check first with the boot manufacturer.

Alpine norm ISO 5355: These boots are designed for use with a pair of classic skis with alpine bindings and not with a monoski, snowboard or skiboard. Touring norm ISO 9523: These boots are designed for use with a pair of touring bindings, and not with alpine bindings, monoski, snowboard or skiboard. It is the skier’s own responsibility if (s)he chooses to take the additional risks. When a pair of used boots is brought in, make sure that any worn parts are still within the norm. Your ski boots must be assembled, adjusted and checked by an approved Salomon technician.

SIZING TABLE INFORMATION SIZE CHART PER FRANCHISE BOOT FRANCHISE

BOOT

TECHNICAL MANUAL ALPINE 2020/21

S/RACE

110

S/MAX RACE

S/MAX

S/MAX WOMEN

FOOT LENGTH RANGE (mm)

MONDO

EURO

BOOT SOLE LENGTH (mm)

220 - 229mm

22 - 22,5

35 - 36

2,5 - 3

4 - 4,5

265

230 - 239mm

23 - 23,5

36 2/3 - 37

4 - 4,5

5,5 - 6

275

240 - 249mm

24 - 24,5

38 - 39

5 - 5,5

6,5 - 7

285

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

7,5 - 8

295

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

9 - 9,5

305

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

10 - 10,5

315

280 - 289mm

28 - 28,5

44 - 45

9,5 - 10

11 - 11,5

325

240 - 249mm

24 - 24,5

38 - 39

5 - 5,5

6,5 - 7

274

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

7,5 - 8

284

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

9 - 9,5

294

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

10 - 10,5

304

280 - 289mm

28 - 28,5

44 - 45

9,5 - 10

11 - 11,5

314

290 - 299mm

29 - 29,5

45 2/3 - 46 1/3

11 - 115

12,5 - 13

324

300 - 309mm

30 - 30,5

47 - 48

12 - 12,5

13,5 - 14

334

230 - 239mm

23 - 23,5

36 2/3 - 37

4 - 4,5

5,5 - 6

275 284

240 - 249mm

24 - 24,5

38 - 39

5 - 5,5

6,5 - 7

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

7,5 - 8

294

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

9 - 9,5

304

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

10 - 10,5

314

280 - 289mm

28 - 28,5

44 - 45

9,5 - 10

11 - 11,5

324

290 - 299mm

29 - 29,5

44 - 45

9,5 - 10

11 - 11,5

334 264

220 - 229mm

22 - 22,5

35 - 36

2,5 - 3

3 - 3,5

230 - 239mm

23 - 23,5

36 2/3 - 37

4 - 4,5

4,5 - 5

274

240 - 249mm

24 - 24,5

38 - 39

5 - 5,5

5,5 - 6

284

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

6,5 - 7

294

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

8 - 8,5

304

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

9 - 9,5

314

summary <<<

>>>

S/PRO

S/PRO WOMEN

S/PRO HV

S/PRO HV WOMEN

X ACCESS WIDE

X ACCESS WOMEN WIDE

FOOT LENGTH RANGE (mm)

MONDO

EURO

BOOT SOLE LENGTH (mm)

240 - 249mm

24 - 24,5

38 - 39

5 - 5,5

6,5 - 7

284

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

7,5 - 8

294

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

9 - 9,5

304

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

10 - 10,5

314

280 - 289mm

28 - 28,5

44 - 45

9,5 - 10

11 - 11,5

324

290 - 299mm

29 - 29,5

45 2/3 - 46 1/3

11 - 115

12,5 - 13

334

300 - 309mm

30 - 30,5

47 - 48

12 - 12,5

13,5 - 14

344

310 - 319mm

31 - 31,5

48 2/3 - 49

13 - 14

15,5 - 15,5

354

264

220 - 229mm

22 - 22,5

35 - 36

2,5 - 3

3 - 3,5

230 - 239mm

23 - 23,5

36 2/3 - 37

4 - 4,5

4,5 - 5

274

240 - 249mm

24 - 24,5

38 - 39

5 - 5,5

5,5 - 6

284

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

6,5 - 7

294

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

8 - 8,5

304

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

9 - 9,5

314

240 - 249mm

24 - 24,5

38 - 39

5 - 5,5

6,5 - 7

285

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

7,5 - 8

295

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

9 - 9,5

305

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

10 - 10,5

315

280 - 289mm

28 - 28,5

44 - 45

9,5 - 10

11 - 11,5

325

290 - 299mm

29 - 29,5

45 2/3 - 46 1/3

11 - 115

12,5 - 13

335

300 - 309mm

30 - 30,5

47 - 48

12 - 12,5

13,5 - 14

355

310 - 319mm

31 - 31,5

48 2/3 - 49

13 - 14

15,5 - 15,5

355

320 - 329mm

32 - 32,5

50 - 51

14,5 - 15

16 - 16,5

375

330 - 339mm

33 - 33,5

51 2/3 – 52 1/3

15,5 -16

17 – 17,5

375

275

220 - 229mm

22 - 22,5

35 - 36

2,5 - 3

3 - 3,5

230 - 239mm

23 - 23,5

36 2/3 - 37

4 - 4,5

4,5 - 5

275

240 - 249mm

24 - 24,5

38 - 39

5 - 5,5

5,5 - 6

285

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

6,5 - 7

295

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

8 - 8,5

305

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

9 - 9,5

315

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

7,5 - 8

296

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

9 - 9,5

306

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

10 - 10,5

316

280 - 289mm

28 - 28,5

44 - 45

9,5 - 10

11 - 11,5

326

290 - 299mm

29 - 29,5

45 2/3 - 46 1/3

11 - 115

12,5 - 13

336

300 - 309mm

30 - 30,5

47 - 48

12 - 12,5

13,5 - 14

346

310 - 319mm

31 - 31,5

48 2/3 - 49

13 - 14

15,5 - 15,5

356

266

220 - 229mm

22 - 22,5

35 - 36

2,5 - 3

3 - 3,5

230 - 239mm

23 - 23,5

36 2/3 - 37

4 - 4,5

4,5 - 5

276

240 - 249mm

24 - 24,5

38 - 39

5 - 5,5

5,5 - 6

286

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

6,5 - 7

296

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

8 - 8,5

306

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

9 - 9,5

316

BOOT

BOOT FRANCHISE

TECHNICAL MANUAL ALPINE 2020/21

SIZING TABLE INFORMATION

>>> 111

summary <<<

SIZING TABLE INFORMATION

SHIFT PRO

SHIFT PRO WOMEN

QST ACCESS

TECHNICAL MANUAL ALPINE 2020/21

QST ACCESS WOMEN

MTN

MTN WOMEN

BOOT

JUNIOR

112

FOOT LENGTH RANGE (mm)

MONDO

EURO

BOOT SOLE LENGTH (mm) 276

220 - 229mm

22 - 22,5

35 - 36

2,5 - 3

3 - 3,5

230 - 239mm

23 - 23,5

36 2/3 - 37

4 - 4,5

4,5 - 5

276

240 - 249mm

24 - 24,5

38 – 39

5 - 5,5

5,5 - 6

286

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

7,5 - 8

296

260 - 269mm

26 - 26,5

41 – 42

7,5 - 8

9 - 9,5

306

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

10 - 10,5

316

280 - 289mm

28 - 28,5

44 – 45

9,5 - 10

11 - 11,5

326

290 - 299mm

29 - 29,5

45 2/3 - 46 1/3

11 - 115

12,5 - 13

336

300 - 309mm

30 - 30,5

47 - 48

12 - 12,5

13,5 - 14

356

310 - 319mm

31 - 31,5

48 2/3 - 49

13 - 14

15,5 - 15,5

356 276

220 - 229mm

22 - 22,5

35 - 36

2,5 - 3

3 - 3,5

230 - 239mm

23 - 23,5

36 2/3 - 37

4 - 4,5

4,5 - 5

276

240 - 249mm

24 - 24,5

38 - 39

5 - 5,5

5,5 - 6

286

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

6,5 - 7

296

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

8 - 8,5

306

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

9 - 9,5

316

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

7,5 - 8

298

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

9 - 9,5

308

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

10 - 10,5

318

280 - 289mm

28 - 28,5

44 - 45

9,5 - 10

11 - 11,5

328

290 - 299mm

29 - 29,5

45 2/3 - 46 1/3

11 - 115

12,5 - 13

338

300 - 309mm

30 - 30,5

47 - 48

12 - 12,5

13,5 - 14

358

310 - 319mm

31 - 32,5

48 2/3 - 49

13 - 14

15,5 - 15,5

358 278

220 - 229mm

22 - 22,5

35 - 36

2,5 - 3

3 - 3,5

230 - 239mm

23 - 23,5

36 2/3 - 37

4 - 4,5

4,5 - 5

278

240 - 249mm

24 - 24,5

38 - 39

5 - 5,5

5,5 - 6

288

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

6,5 - 7

298

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

8 - 8,5

308

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

9 - 9,5

318

240 - 249mm

24 - 24,5

38 - 39

5 - 5,5

6,5 - 7

281

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

7,5 - 8

291

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

9 - 9,5

301

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

10 - 10,5

311

280 - 289mm

28 - 28,5

44 - 45

9,5 - 10

11 - 11,5

321

290 - 299mm

29 - 29,5

45 2/3 - 46 1/3

11 - 115

12,5 - 13

331

230 - 239mm

23 - 23,5

36 2/3 - 37

4 - 4,5

4,5 - 5

271

240 - 249mm

24 - 24,5

38 - 39

5 - 5,5

5,5 - 6

281

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

6,5 - 7

291

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

8 - 8,5

301

270 - 279mm

27 - 27,5

42 2/3 - 43 1/3

8,5 - 9

9 - 9,5

311

140 - 149mm

22-23

7,5 K

C208

150 - 159mm

24 2/3

8,5K

C208

160 - 169mm

9,5K

C208

170 - 179mm

27 2/3

10,5K

C224

180 - 189mm

18.0-18.5

29 - 30

11,5K - 12K

12 - 12,5

C235

190 - 199mm

19.0-19.5

30 2/3 - 31 1/3

12,5K - 13K

13 - 13,5

C235

200 - 209mm

20.0-20.5

32 - 33

13,5K- 1

1 - 1,5

C246

210 - 219mm

21.0-21.5

33 2/3 - 34 1/3

1,5 - 2

2 - 2,5

C255

220 - 229mm

22 - 22,5

35 - 36

2,5 - 3

3 - 3,5

A265

230- 239mm

23 - 23,5

36 2/3 - 37 1/3

4 - 4,5

4,5 - 5

A275

240 - 249mm

24 - 24,5

38 - 39

5 - 5,5

6,5 - 7

A285

250 - 259mm

25 - 25,5

39 2/3 - 40 1/3

6 - 6,5

7,5 - 8

A295

260 - 269mm

26 - 26,5

41 - 42

7,5 - 8

9 - 9,5

A305

summary <<<

BINDING COMPATIBILITY

BOOT FRANCHISE

CHILDREN NORM

ADULT NORM

CUSTOM SHELL PROCEDURE

FAQ

WHY / WHAT IS CUSTOM SHELL ?

GENERATIONS

SALOMON CUSTOM SHELL TAKES BOOT CUSTOMIZATION BY A COMPLETELY ADAPTING SHELL AND CUFF TO THE SHAPE OF SKIER’S FEET, ANKLES AND LEGS THROUGH A QUICKER FITTING PROCESS. 1ST GENERATION (2008): IN-MOLD TECHNOLOGY Lateral forefoot zone, base of the shell

2ND GENERATION (2009): DUAL INJECTION TECHNOLOGY Complete forefoot zone + ankle +heel

3RD GENERATION (2012): DUAL INJECTION TECHNOLOGY

4TH GENERATION (2013): CUSTOM SHELL ON CUFF

EXTENDED CUSTOM SHELL AREA ON CUFF

5TH GENERATION (2018) : SA.FW16.ALPINE_FIT_BOOT_TRAINING_MANUAL_R07.indd 55

BENEFITS • Faster process (2x faster vs CS 360°) • Allow the foot to be closer to the shell without generating additional pain

9/21/16 1:13 PM

BOOT

360° CUSTOM SHELL AVAILABLE ON THE MAX AND PRO SERIES PRODUCTS EXCEPT XPRO 90, XPRO 80, XPRO 80W, XPRO 70W

TECHNICAL MANUAL ALPINE 2020/21

Full lower part of the shell

113 summary <<<

CUSTOM SHELL PROCEDURE & FAQ

STEPS FOR CUSTOM SHELL CUSTOM SHELL TIMING PROCEDURE

WARM UP

STEP IN & EXPAND

COOL DOWN

CUSTOM SHELL HD

2’

3’

5’

CUSTOM SHELL

10’

4’

6’

WARM UP

STEP-IN & EXPAND

COOL DOWN

CUSTOM SHELL OVEN AND FITTING PROCEDURE 1. Pre-heat Custom Shell oven for 5 minutes.

8. H ave cutomer stand into theboot according timing procedure : - 3 minutes for Custom Shell HD. - 4 minutes for Custom Shell.

2. Remove each liner form each shell. 3. Place shells with buckles open in Custom Shell oven and set timer according timing procedure : - 2 minutes for Custom Shell HD. - 10 minutes for Custom Shell. 4. Using Custom Shell gloves or insulated gloves, carefully remove heated shells from the oven after the requested time of heating. WARNING : do not allow customer to touch the boot as the hot plastic and buckles can burn.

9. A fter requested time to extand the boots, place a Custom Shell cooling packs on each boot and have the customer wait motionless for another following time : - 5 minutes for Custom Shell HD. - 6 minutes for Custom Shell. 10. After requested time to cool down the boots, remove Custom Shell cooling packs, undo buckles and power strap, and have customer exit the boots.

5. C arefully insert each liner into each shell. 6. Help the customer step into the boots. 7. O nce in the boots, close the buckles on a setting that provide minimum tension and gently close power strap. WARNING : buckle with tension can warp the plastic where the buckles are mounted.

11. Ensure the boots are colsed properly and tell the customer not to ski in them for 3 hours to ensure complete hardening of the Custom Shell plastic. After 3 hours, the boots are ready to be skied.

BOOT

TECHNICAL MANUAL ALPINE 2020/21

WARNING : ask customer to stand still without flexing nor walking in the boots. Normal standing. allows the shell, cuff and liner to shape to the feet and the legs.

114 summary <<<

CUSTOM SHELL PROCEDURE & FAQ

FAQ CUSTOM SHELL 360°

FAQ CUSTOM SHELL HD

What is the advantage compared to normal bootfitting?

What does HD means ?

Here, it is the foot which changes the shell, there is no more risk of misinterpretation, the precision is perfect. Also, this process saves time (30 min. to do everything & the customer leaves with his/her boots) and an easier manipulation (every KOTF can do it).

• HD means High Definition

Can the shell change forms several times? As many times as you want! The wider the foot, the more the shell will expand. But it won’t come back…

What is the difference versus the Custom Shell 360°? • The new custom shell process is 2 times faster (10min against 20min) It allows also an even more detailed customization of the shell around the foot

How can it be possible/achievable? • Compoundage • Thinner walls construction

What is the maximum width the shell can expand to? Up to 6 mm with the push of the foot only.

How different is the process vs CS 360°?

Mold the soles before. The customer should then step in the warmed Custom Shell with the insoles.

Does the plastic retract the same as normal boots when cooled?

• Same oven, same oven temperature (100°C), same cooling packs

Which model of Salomon alpine boot benefit from this new technology?

Yes, but two times less than normal plastic: approximately 25% after the boots have been taken out (a shell pushed out 4mm could come back to 3 mm).

For the FW18 season, the whole S/MAX Men range is equipped with the CS HD techno (S/MAX Race 130, S/MAX Carbon 130, S/MAX 130, S/MAX 120, S/MAX 110, S/MAX 100). The MTN collection is also available with the CS HD (S/LAB MTN, MTN Explore Men, MTN Explore Women)

What is the benefit of Custom Shell versus the Custom Fit? Should you do it before or after?

Which parts of the boot can be customizable?

The work done on the shell must be done before. This will solve problems and last over time. The molding of the liner must be done after in order to put the finishing touches on the fit.

How do I know when the plastic is warm enough? It is the same process as usual when done with a manual test.

What is the ideal temperature to form the Custom Shell? 108°C at core of the plastic.

How many years of R&D did it take to develop the Custom Shell technology? 3 years.

Which is the impact of the new material on the performance of the boot?

Lower shell only (S/MAX & MTN) but also including the malleolus areas & the lower area of the chassis vs the Twinframe technology

When heating the boot, is there a risk of modifying the geometry of the boot? No because thanks to the Coreframe insert, which doesn’t content Capa, the boot will deform exactly where it has to. The size and the shape of the Coreframe, whatever its composition (Carbon T-Pex, Xecarb or Fiberglass) is designed to GUARANTEE the integrity of the chassis geometry.

What happens if I leave the boot in the oven for longer than 2 minutes? You could still put it 10 minutes and there would be no difference. The answer comes from the materials found in the shell. They only need 2 minutes to completely absorb the heat they need to deform, but do not deform more if you leave them in the oven longer.

There is no effect because the material has the same PU base as a normal boot. The boot has exactly the same behavior on snow. On the other hand, once a boot is fit with the Custom Shell, precision is increased.

TECHNICAL MANUAL ALPINE 2020/21

Should the custom soles be done before or after?

In World Cup races, one person is dedicated to each racer; everything is done by hand and each pair is adapted to each discipline. Then you could say having Custom Shell is like having your own race technician!

BOOT

Why is Custom Shell not used in World Cup?

115 summary <<<

CUSTOM FIT PROCEDURE WHY / WHAT IS CUSTOM FIT ? SALOMON CUSTOM FIT TAKES BOOT CUSTOMIZATION BY A COMPLETELY ADAPTING LINER TO THE SHAPE OF SKIER’S FEET, ANKLES AND LEGS THROUGH A QUICKER FITTING PROCESS. ■ THERMOFORMABLE ZONES

■ NON-THERMOFORMABLE ZONES

1. Straight and anatomical tongue - A thermoformable internal side that provides precision and comfort. - An external side that is more rigid on the tibia and more supple in the flex area for excellent pressure distribution without hindering flex.

3. Asymmetrical and rigid cuff Distributes pressure for instantaneous transmission of efforts.

2. Opened ankle area For ideal morphological adaptation regardless of the size and shape of the bones.

7. Forefoot The space in front of the metatarsal is not thermoformable, which allows the toes to move freely.

4. Watertight gusset 5. Specific cuts For women and men to avoid pressure points on the lower calf. 6. More supple zones Allow for easy entry/exit of the boot.

CUSTOM FIT PROCEDURE 1. Pre-heat Custom Fit machine for 5 minutes.

Procedure to remove batteries (fig. 2)

2. Place complete boot with buckles open in Custom Fit machine and set timer for 5 minutes (fig. 1)

3. Carefully remove boots with heated liner from the machine after the requested time of heating.

BOOT

TECHNICAL MANUAL ALPINE 2020/21

4. Help the customer step into the boots. WARNING : before step into boots, Customer should wear ski socks with following caracteristics : - Socks that go higher than top of the boot. - Socks with at least 45% wool. Wearing normal and/or low-cut socks could cause skin reactions due to the heating process. 5. Once in the boots, close the buckles on a setting that provide minimum tension and gently close power strap.

WARNING : for Custom Heat liner, the 2 batteries which are inside each the liners should be removed before Custom Fit heated process.

6. Have cutomer stand into the boot during 10 minutes and ask him following steps to help the right forming of the liner aroud the foot : - Tape the heel on the floor to make a good impression of the achilles’heel (fig. 3) - Make sevrals flex movements to simulate the anklebone movements when skiing. 7. After requested time to form the liner, undo buckles and power strap, and have customer exit the boots. 8. Ensure the boots are colsed properly and tell the customer not to ski in them for 30 minutes to ensure complete hardening of the Custom Fit liner. After 30 minutes, the boots are ready to be skied.

116 summary <<<

HOW TO MESURE A FOOT

THIS MEASURER ALLOWS MEASURES OF : • Length : US Sizes / UK Sizes / French Sizes / real mondopoint • Width : measured in mm, this value linked to the foot length can give an indication to help for the choice of the boot last : › N = Narrow feet = Boot last between 95 and 98mm › S = Standard feet = Boot last between 98 and 102mm › W = Wide feet = Boot last between 102 and 106mm

TECHNICAL MANUAL ALPINE 2020/21

MAINTENANCE RECOMMENDATIONS Use a damp cloth to clean the measurer. It is prohibited to use chemical agents, hot water, pressurized water, gasoline, alcohol, detergents, solvents or aerosols, which could permanently damage the plastic materials and erase the marks.

THIS MEASURER ALLOWS MEASURES OF: - Length: real Mondopoint/french sizes/UK sizes/US sizes

BOOT

WARNING Salomon developed a foot measurer that will help you provide better customer service by being able to recommend the size that corresponds to the dimensions (length and width) of the skier’s feet. However, using the measurer can never replace trying on a boot. The volume fit can be measured in two dimensions. The morphology of the foot and physical sensitivity of each individual, according to his/her sports activities and level (comfort/performance ratio), are also determining factors in the choice of size. The Salomon measurer can be used for all Salomon footwear products (Alpine, X-C, Hiking, In-line skates, Snowboard) and takes into account the two fundamental dimensions of both feet. › The length (main measurement): it can be read directly on 5 international size scales (US men’s/ US women’s/ UK / EUR / Mondopoint). › The width in direct correlation with the length measured. The width measurement is particularly useful to refine the measurement in Mondopoint because it orients the customer towards the .0 sizes (narrow feet) or .5 sizes (wide feet).

117 summary <<<

BOOT FEATURE / CUSTOMIZATION WOMEN CALF ADJUSTMENT Fig.1 > Fig.4 Only one screw turn to enlarge the upper cuff up to 1cm to fit all legs shapes easily and quickly. Women cuff opening is adjustable. Cuff is delivered with opened position which allows a large volume for calf. It is possible to reduce the calf volume by turning the screw present on the cuff.

Cuff opened

Cuff opened (maximum calf volume)

4 Cuff closed

3D PLATE ADJUSTMENT The 3D plate adjustment allows the position of the instep buckle to be changed for personalized foot hold : - Unscrew the buckle with a torx T20 wrench - Position the buckle over the plastic lung on the shell - Tighten in the alternate position

ADJUSTABLE MICRO BUCKLE Buckle length can be adjusted by turning the buckle to the desired fit

BOOT

TECHNICAL MANUAL ALPINE 2020/21

Cuff closed (minimum calf volume)

118 summary <<<

ADJUSTABLE BUCKLE TEETH Buckle teeth position can be adjusted on the boot cuff to allow a lower leg adjustment (+/-20mm) : - Loosen the screw with a torx T20 wrench - Tighten the screw and buckle teeth in the appropriate position

BOOT FEATURE / CUSTOMIZATION

CANTING

BOOT CANTING CAN BE ADJUSTED BY FOLLOWING OPERATIONS BY AN APPROVED SALOMON TECHNICIAN INTERNAL BOOT SOLE GRINDING TO THE APPROPRIATE ANGLE

Boot sole grinding

OPTIONAL CANTABLE PADS Using optional cantable pads to be grinded to the appropriate angle Cantable alpine pads are not compliant to ISO5355 and must be bringing before using to reach the alpine norm and to fit into the binding. Grinding should be done as well on the top and on the bottom of the front and rear cantable pad with the same angle in order to guarantee surfaces parallelism. Grinding on the top and the bottom surface should not go over the reference line marked on the cantable alpine pads which allow an angle from 0 to 1,5°. TWO REFERENCES OF ALPINE DIN ARE EXISTING DEPENDING OF THE CONCERNED BOOT MODEL :

TECHNICAL MANUAL ALPINE 2020/21

L 36225400: XPro – Quest Access - Quest Max – Quest Pro – Ghost Max L391764000: QST Pro

Top pad grinding (not over reference line taht is to say 1,5° maximum)

MAX 2 MM TO GRIND

NO GRINDING

MAX 2 MM TO GRIND

BOOT

Bottom pad grinding (parallel to top grinding

>>> summary <<<

119

BOOT FEATURE / CUSTOMIZATION

CANTOLOGY KIT Using Cantology kit available on the market an also available as spare part • This kit allows an adjustment from 0,5 to 4mm depending chosen cant • Cantology cants fit between ski boot layer boot and ski boot lifters • After cantology cant installation, boot toe and heel heights must be routed to restore the original ISO 5355 toe and heel height dimensions.

CANTABLE OVERSIZE PIVOT Using cantable Oversize Pivot already pre-mounted on S/RACE model and available as spare part for S/MAX – S/PRO – S/PRO HV models. To install cantable oversize pivot on S/Max – S/Pro – S/Pro HV models, shell grinding is necessary with the kit and procedure described below: Tools

BOOT

TECHNICAL MANUAL ALPINE 2020/21

THIS KIT IS SUITABLE FOR FOLLOWING MODELS : S/RACE – S/MAX – S/PRO – S/PRO HV

120 summary <<<

BOOT FEATURE / CUSTOMIZATION

BOOSTER FLEX ADJUSTMENT

SENSE STRAP ADJUSTMENT SENSE STRAP Sense strap allow to adjust and manage boot sensations:

CUSTOM HEAT LINER & CUSTOM HEAT CONNECT LINER SALOMON IS OFFERING 2 TYPES OF HEATED LINERS IN HIS RANGE : 1. CUSTOM HEAT LINER

BOOT

Heating management is done by a button present on the lateral side of each liner. 3 warmth positions are available for customized comfort has showed below :

TECHNICAL MANUAL ALPINE 2020/21

Booster flex is present on the back of the cuff on models equipped with this feature. This function allows : - Increases the junction between cuff and shell for flex management in a forward position : entering the curve, increasing power on skis. - Provide support and power to skiers in a rear position Out of the box, booster flew is adjuster on soft position. To harden the boot, unscrew the 2 torx T20 screws, inverse booster flex position and screw it again.

121 summary <<<

BOOT FEATURE / CUSTOMIZATION

2. CUSTOM HEAT CONNECT LINER Heating management is done trought a Smartphone using Bluetooth connection and operating system IOS9+ and Android V6+ (Marshmallow and later versions). Before the use of the system, following operations shoud be done : Model • Download CustomCUSTOM Heat Connect Application on the Smarthphone trough the ModelCONNECT HEAT App Store and Google Play Store CUSTOM HEAT ModelCONNECT • Pair the boots with the Smarthphone trough Bluetooth technology

CUSTOM HEAT CONNECT

HOW TO CHARGE CUSTOM HEAT & CUSTOM HEAT CONNECT MODELS CUSTOM HEAT LINER DESCRIPTION - 1.1 Function key + heating indicator light - 1.2 Charging plug - 1.3 Liner Custom Heat connector - 1.4 Pouches for batteries - 1.5 Lithium-ion “Dual” batteries 3.7V/2600mAh

Custom Heat Connect Custom Heat Connect DISPONIBLE SUR

DISPONIBLE SUR

Custom Heat Connect DISPONIBLE SUR

= =

°C - °F °C - °F

? == FAQ °C - °F ? = FAQ

PROGRAM = ? = FAQ PROGRAM = PROGRAM

1 x 1" 1 x 1" 1 x 1"

1 x 1"

/ 31 / 31 /

OFF OFF OFF

Confort Confort

Charger description - 2.1 Power supply cable USB/USBC - 2.2 Battery charge indicator Battery warranty policy: The battery is excluded from general Salomon warranty and is available as spare part .

BOOT

TECHNICAL MANUAL ALPINE 2020/21

Confort

122 summary <<<

BOOT FEATURE / CUSTOMIZATION

FAQ CUSTOM HEAT CUSTOM HEAT DEVICE 1.1

What is the meaning of the 2 red lights at the middle of the device?

Red lights in the middle of the device indicate the battery status. When they start to blink whilst skiing, it means your battery level is low and you will have to charge it soon. When charging your batteries packs, light will blink until your batteries are fully charge. When the red light is constant, it means your batteries are fully charged.

1.2

What is the meaning of the colored lights of the device?

Colors means different mode. The blue light indicates the first level of heating. The yellow light indicates the second level of heating: “COMFORT ZONE”. The red light indicates the third level of heating.

1.3

What is the default temperature of the shoes if I do not use a smartphone?

When manually using Salomon Custom Heat Connect, the target temperature recorded is the last one setup with your APP. If you don’t use APP, the default temperature is 20°C.

1.4

Can I set my own target temperature without smartphone?

You must use Salomon Custom Heat Connect APP to setup your own target temperature.

1.5

Can I control the left and right foot separately?

It is not possible to control independently the right and left shoe.

1.6

How and why do I reset my device?

APP and Salomon Custom Heat system are using specific security authentication. If you have a new device or download de latest APP, you may have to reset your shoes. To reset your shoes, hold down the button for 5 secs until all lights turn red then release the button: your shoes have now been reset.

How do I connect my shoes?

Press the buttons on both shoes until the lights turn blue. Bring your device closer to the shoes and tap on the “Connect to your boots” button in Salomon Custom Heat Connect APP

2.2

My shoes are ON but my application cannot detect them, why? (android only)

If you have disabled localisation on your phone or if you did not permit the Salomon Custom Heat Connect application to use your location, bluetooth devices will not be detected. Please verify the permission of the app in your phone applications settings.

2.3

How do I automatically connect to my device?

After your first connection, your APP will remember which shoes are yours. So next time you open the application, it will search and connect automatically to the recorded shoes.

2.4

How do I release locker icon from my devices?

The locker icon means that the shoes you try to connect are already secured. To release the security, hold down the button of your shoes for 5 secs, until all lights are red and the locker icon disappears.

2.5

Can I connect to multiple pairs of shoes at the same time?

Salomon Custom Heat APP is designed to control only 1 pair of shoes at a time.

2.6

What happen if I lose my phone?

If you lose your phone, you can still use your shoes in manual mode by pressing the button once. If you want to connect a new phone, you will need to release the security of your shoes by holding down the button for 5 secs, until all the lights shine red. The temperature will be the last saved temperature on your phone.

2.7

Why has my smartphone been disconnected from the shoes after long time switched off?

When you turn off your phone in sleep mode for a short or long period, your smartphone may automatically disable wireless function in order to save smartphone battery. The liner continues to work normally. When you turn on your phone, Salomon Custom Heat App will automatic reconnect to the shoes.

2.8

From how far can I detect my shoes?

When using the APP for the first connection, you need to position your smartphone very near to the shoes (1 meter). After the first connection, your APP will find your shoes from a range of 10 to 15 meters.

2.9

I downloaded a new APP version and I cannot connect to my shoes anymore?

When you update Salomon Custom Heat App, it will reset all data from your phone. You just need to reset your shoes to connect to your shoes again.

BOOT

2.1

TECHNICAL MANUAL ALPINE 2020/21

BLUETOOTH PAIRING

123 summary <<<

REPLACEMENT PROCEDURE HOW TO CHANGE A BUCKLE (OR ANY RIVETED COMPONENTS) REQUESTED TOOLS : • Safety glasses • Boot fixation device • Metal center punch • Hammer • Driller • Sharp drill bit designed for metal (slightly smaller diameter compared the rivet head you will be drilling out) • Screw and T-nut of the required depth and diameter • Matching driver • Blue Loctite (or similar non permanent thread locking agent)

PROCEDURE 1. Remove liner from the shell 2. Secure the boot in a device that holds the boot at the heel & toe 3. Using the metal center punch & hammer, dent the head of the rivet (this provides a more secure area that prevents the drill bit from sliding off the rivet and which could damage the boot)

5. Remove old buckle and metal shavings that resulted from drilling out the old buckle. 6. Add Loctite to the screw’s threads (be aware that most thread locking agents set in 10 minutes but take 12-24 hours for fully harden).

BOOT

TECHNICAL MANUAL ALPINE 2020/21

7. Place new buckle on the boot (helpul hint : tape the buckle in an open position so that you don’t need to hold it open when trying to install).

124

4. Drill out the rivet at a perpendicular angle

8. Assemble and tighten as necessary (and remove tape if you followed the helpful hint)

WARNING : - Not drill at a low angle as the drill can slip and then damage the boot - Be careful when drilling out the final rivet as the buckle can get stuck on the drill bit, spin around, and cause injury to the boot-fitter - Not drill for long periods of time on the rivet. The amount of friction will heat up the plastic and potentially damaging the plastic of the boot. summary <<<

HOW TO CHANGE A STRAP OR A RENTAL PLATE Same procedure as buckle replacement described on the previous paragraph.

REPLACEMENT PROCEDURE

HOW TO CHANGE PADS INTERCHANGEABLE PADS L40753000 – X Access Gripwalk pads

ALPINE DIN These are the traditional flatter alpine soles without rubber. They follow ISO5355 and work safely with traditional alpine bindings following ISO9462. They also work safely with WTR and MNC bindings certified.

WALK SOLE GRIP WALK The walk sole Grip Walk are intended to be used only with following bindings : • Ski touring bindings compliant with ISO 13992 • Alpine ski bindings labeled Grip Walk or Multinorm Certified MNC Technology or WTR Technology* (compliant with ISO9462) in exclusion to all other alpine binding *The Dual WTR Rossignol and Tyrolia MBS models have to be adjusted in Alpine position

L40760200 – S/Max range (excepted S/Max 130 Race), S/Max 70, S/Max 65, S/Race 65, S/Pro Gripwalk pads, S/Pro HV

L40753100 – X Pro, Quest Access, QST Access Gripwalk pads

SOLE PADS CHANGING PROCEDURE

> Use only a manual screw driver > Remove the rear and front sole

BOOT

Sole pads references mentioned above are removable and should be replaced if excessively worn and/or damaged. Salomon guarantees the soles for their disassembling and reassembling, up to a maximum of 10 times subject to strict compliance with the following instructions:

TECHNICAL MANUAL ALPINE 2020/21

L40901300 - Junior (A) Gripwalk pads from size 22 to 26,5 – T3, S/Max 60T, S/Race 60T

> Push them forward towards the front / rear of the shell and screw until you feel an increased resistance in the torque to reach a torque value about 1,5Nm

125

> Unscrew the 7 screws and remove them from the sole

summary <<<

FOOT ANATOMY AND FIT NOTIONS OF ANATOMY

A basic knowledge of anatomy of the foot is essential if you are going to understand and solve your customersâ&#x20AC;&#x2122; problems and needs since each foot is unique.

1. THE BONES OF THE FOOT (fig. 1)

A. POSTERIOR TARSUS 1. Calcaneus 2. Talus (Astragalus) 3. Trochlear surface

B. ANTERIOR TARSUS 4. Navicular bone (Tarsal Scaphoid) 5. Cuboid bone 6. 3 cuneiform bones

C. METATARSUS 7. 5 metatarsal bones

D. TOES 8. 14 phalanges

BOOT

TECHNICAL MANUAL ALPINE 2020/21

2. D ISTORTION OF FOOT WHEN WEIGHTED

(fig. 2) When the foot is weighted (standing position), it can change in size: - lengthwise, it can get 5 mm longer, - widthwise, it can get 12 mm wider. When the foot is flexed, we notice: - the circumference of the ankle increases about 2 mm, - the axis between the talus (astragalus) and calcaneus becomes off-centered which increases the surface area at the base of the foot. Therefore, to be accurate, feet should be measured when the person is standing with his/her weight distributed on both feet and knees slightly flexed.

3. TYPES OF LEGS (fig. 3) Some people naturally have varus or valgus knees. The boot cuff follows the profile of the leg. Therefore, the boot sole forms an angle with the ground (= the ski is not flat). The ski boots can be adapted to the shape of the leg by canting the cuff. The canting adjustment by canting the cuff allows the boot to follow the morphology of the leg to keep skis flat.

A: Normal knees.

126 summary <<<

B: Varus knees.

C: Valgus knees.

FOOT ANATOMY AND FIT

4. TYPES OF FEET (fig. 4) A deeper analysis of the customer’s feet is necessary to observe the possible deformations that can become problem areas. Salomon has parts at your disposal that will help you to easily adapt the boots to these deformations. › High arches: The skier needs an arch support that can relieve pressure on ‘overloaded’ areas. Arch supports can be attached to the footboards (fig. A). › Supinated or pronated feet: This is the deviation of the foot’s vertical axis towards the medial or lateral side, which can lead to problems in the areas of the anklebones, navicular bone or talus. To adapt to this deviation of the foot, it is possible to place wedges directly on the footboard. However, this wedge should only be used if the lateral articulation under the ankle bone is mobile (fig. B). › High instep: You can grind the footboard (Falcon and X Wave) to increase the volume. This sole is realized in grindable PU foam. To increase the volume of the boot or to change the position of the foot. Caution, grind on the top surface only. Grinding the base will effect the interface with the Chassis. A depth gauge is marked front and back for even grinding (fig. C).

1. Pronated flat foot.

2. Normal foot.

3. Supinated high-arched foot.

› Low instep: The height and inclination of the footboard can be modified by adding: – heel lifts (fig. D).

BOOT

The modifications that can be made on the Salomon boots should be considered as the ‘final touch’ of personalization. Before undertaking this type of operation, it is important to observe certain basic rules: - A lways proceed step by step, starting with temporary measures before going on to permanent changes. - If you decide to proceed with the permanent modifications as a last resort, they are entirely your responsibility. They require the proper tools and should be undertaken only for big problems and by experienced specialists. For example: - Stretching the shell. - G rinding the liner (not recommended for manufactured liners). - Grinding the shell. Important: Boots whose lower shell material is not made of Polyurethane (PU), should not be heated (risk of damaging the material).

TECHNICAL MANUAL ALPINE 2020/21

5. RECOMMENDATIONS

127 summary <<<

TECHNICAL MANUAL ALPINE 2020/21

FOOT ANATOMY AND FIT

PROBLEMS

CAUSES SOLUTIONS

FIRST METATARSAL PRESSURE (medial side of the forefoot)

Shell too narrow. Prominent first metatarsal.

Solutions all products: › Stick adhesive foam around the first metatarsal on the medial side of the liner (fig. A). › Stretch the shell locally with a heat gun* and other tools designed for this purpose (such as SIDAS) (except Symbio and Rear Entry). X Wave, Ellipse, Performa: Be careful not to overheat the Sensifit or instep gusset of the boot during the heating operation (there is a risk of deforming it due to how thin this part is).

FIFTH METATARSAL PRESSURE (lateral side of the forefoot)

Shell (or liner) too narrow. Prominent fifth metatarsal.

Solutions all products: › Remove the insole (increases volume). › Stick adhesive foam around the painful area to dissipate the pressure (fig. B). › Stretch the shell locally using a heat gun* and other tools designed for this purpose (such as SIDAS) (except Symbio and Rear Entry). X Wave, Performa: Be careful not to overheat the Sensifit or the instep gusset of the boot during the heating operation (there is a risk of deforming it due to how thin this part is).

ANKLEBONE PRESSURE Pain/pressure behind one or both ankle bones.

Prominent medial and lateral ankle bones. Heel shape.

Solutions for Falcon, X Wave, Performa: Special precautions are required when stretching the shell: › Heat* the inside and outside of the cuff and lower shell simultaneously (so that both will be at the same temperature despite their different thicknesses and layers). › Place the stretching device on the inside, close the boot during the stretching operation, and proceed with very small successive degrees of stretching to avoid creating a space between the cuff and the shell. Falcon and X Wave: Be careful not to heat the metal parts (there is a risk of damaging the plastic). Solutions for Rear-Entry models: › Remove the insole to increase the volume. › Stick a C-shaped foam pad in the area around the ankle bones (on the liner) (fig. C). › Remove some foam from the liner in the area around the ankle bones. › Add shims to blue heel envelopment plate.

HEEL PRESSURE

Lack of room in the boot. Prominent calcaneus (exostosis).

Solutions all products: › Stick a chevron (foam pad in the form of an inverted V) above the calcaneus to push the foot forward in the shell and reduce the pressure on the heel (fig. D). › It is possible to remove some PU from both sides of the Achilles tendon on the cuff (grinding) and/or on the lower shell (Falcon, X Wave, Ellipse and Performa).

BOOT

*Caution: The boots whose lower shells aren’t made of Polyurethane (PU) must not be stretched with heat (there is a risk of damaging the material).

128 summary <<<

FOOT ANATOMY AND FIT

HEEL MOVEMENT

CAUSES SOLUTIONS Very narrow heel. Achilles tendon axis very hollow. Thin ankle.

Solutions all products: › Stick a chevron above the calcaneus on the liner (fig. E). › Stick an L-shaped piece of foam under each ankle bone (for better grip). › Add a shim to the top of the liner (forward position that pushes the foot backward in the boot and increases pressure on the heel). › Use a thicker insole. › Add a shim under the footboard. › Add heel lifts (fig. F).

Poor blood circulation caused by pressure on the blood vessels/ nerves. Poor foothold distribution (especially with children).

Solutions all products: › Make sure the adjustments are not too tight. › Remove the insoles from the liners. › Add a small arch support and varus wedge (or a shim on the inside of the heel under the footboard from the performance series). › Grind the footboard.

CRAMPS Muscle pain under the arch, in the calf, pressure points, irritations.

Pronounced arch, high instep or flat foot. Pronated foot. Thick lower leg.

Solutions all products (fig. H): › Add or remove the arch support. › Add an insole or propose a custom insole. › Remove all shims under the footboard. › Modify the angle of the forward lean to distribute the skier’s weight differently. › Grind the footboard. › Grinding the Custom Sole: To increase the volume of the boot or to change the position of the foot. Caution, grind on the top surface only. Grinding the base will affect the interface with the Chassis. A depth gauge is marked front and back for even grinding.

SHIN BITE

Lack of pressure distribution.

Falcon (fig. I): › Add a shin wedge on the cuff (choose the mounting position according to the height of the skier).

BOOT

INSULATION AND NUMBNESS Cold, numb feet.

TECHNICAL MANUAL ALPINE 2020/21

PROBLEMS

129 summary <<<

NOTES

ACTIVE PROTECTIVE HELMET GOGGLE POLE BACK PROTECTION

HELMET

HOW TO CHOOSE THE RIGHT HELMET For consumer protection, please read the following guide and follow the given instructions. Helmets are designed to reinforce safety while doing the following winter sports activities: ski, Snowboard, thus excluding all other activities, whether motorized or otherwise.

NORMS

EN-174

ASTM 659-10

CE-EN1077

Google for alpine skiers and snowboarders

Helmets for alpine skiers and for snowboarders (Non motorized winter sports)

ASTM F2040 helmets for recreational snow sports (Non motorized winter sports)

CE-EN1078 Safety standard for bicycle helmets for adults and children age 5 and older

CPSC1203 Safety standard for bicycle helmets for adults and children age 5 and older

CE-EN12492 Alpine climbing standard on selected helmets (non motorized winter sports)

DRIVER MIRAGE / PIONNER VISOR / ICON VISOR / ICON LT VISOR / GROM VISOR / PIONEER LT VISOR respect these 3 standards BRIGADE+ AUDIO / BRIGADE+ / BRIGADE / SPELL+ / SPELL / PACT / BRIGADE RENTAL respect these 4 standards

MTN Lab respect this standard

All Salomon helmets respect these 2 standards

DECLARATION OF CONFORMITY EU declaration of conformity are available on www.salomon.com

HEAD MEASURER Salomon has developed a head measurer that will help you to better serve the consumer by being able to recommend the helmet size that corresponds to the circumference of his/her head. Please remember that the size given by the measurer (centimeters) should be used only as an indication. Using the measurer should never replace trying on the helmet. The final selection of the appropriate size should be left to the customer. Salomon does not cover any damage to the head measurer that is a result of transportation, storage or not abiding by the instructions for use.

RECOMMENDATIONS FOR USE • Position the measurer on the head according to (fig 1), touching the brow (A) and the occipital bone (B).

• Turn the roller (C) until it disengages (fig2).

HELMET

TECHNICAL MANUAL ALPINE 2020/21

WARNING

132 summary <<<

• Read the measurement on the graduated scale (D) in the window (fig.3).

HOW TO CHOOSE THE RIGHT HELMET

HELMET

TECHNICAL MANUAL ALPINE 2020/21

SIZING CHART

133 summary <<<

HOW TO CHOOSE THE RIGHT HELMET

HELMET ADJUSTEMENT

CLEANING OF YOUR VISOR

The helmet must be properly positionned on, and adjusted to the user’s head to ensure maximum comfort and protection and be free of any pressure points. The helmet should sit firmly against the forehead and not slip down over the eyebrows. Adjust the chinstrap firmly beneath the chin and fasten the buckle (fig. 1). Try to move the helmet with both hands from left to right. If the helmet fits correctly, the skin on your forehead should move gently with the helmet (fig. 2).

To clean the lens, use soapy water and rinse it under a stream of lukewarm water. Leave it to dry naturally and wipe with a soft cloth. Do not use alcohol, detergents or solvents. These Salomon visors feature an anti-fog treatment. The inside face of the lens is scratch sensitive and should be treated with caution. Please avoid wiping it. Snow which has penetrated the visor should only be shaken out.

UPKEEP Do not modify your helmet. Do not put varnish or any coloring products on your helmet. Do not cut the ends of the straps. Only use the included stickers on your helmet.

SERVICING Inspect your helmet regularly. If you remark any sign of deformation or damage, replace your helmet. Do not hesitate to show your helmet to a Salomon dealer or contact our customer service department.

REPLACEMENT – WARNING ! ✔ RIGHT

✘ FALSE

In case of children’s helmets, an adult should always check that the helmet is properly secured

HELMET VISOR ADJUSTMENT

This helmet was designed to absorb shocks by deformation or destruction. If your helmet has been subjected to a forceful shock, or involved in an accident, it should be destroyed and replaced even if there is no visible damage because interior damage can occur that weakens the helmet. SALOMON Recommends not use a helmet more than 5 years from the date of manufacture (month/year appears on the sticker inside the helmet).

VISOR INTERCHANGEABILITY

Position the helmet visor on your head, not too far forward nor too far back.

DRIVER / MIRAGE

BUCKLE

HELMET

TECHNICAL MANUAL ALPINE 2020/21

Close the buckle under your chin until you hear a click sound.

VISOR FILTER CATEGORY All Salomon lenses, whatever their color, are compliant to the EN174 : 2001 requirement. For any additional information on lenses, please refer to the Goggles section on www.salomon.com

PIONNER VISOR / ICON VISOR / PIONEER LT VISOR / ICON LT VISOR

MAINTENANCE

1. With a screwdriver, unscrew the rivets on each side of the visor

WE ADVISE YOU TO GIVE INSTRUCTIONS OF USE TO ANY CUSTOMER BUYING A HELMET. STORAGE Helmet must be kept away from all sources of heat. Never expose an helmet to over 40°C. Extended exposure to fierce sunlight may weaken various plastic materials. These conditions often occur within a car parked in the sun.

CLEANING OF YOUR HELMET 1/ External shell: Use only soap and water. Do not use gasoline or any other solvent/chemical substances. 2/ Lining & Ear pads

134 summary <<<

LENS INSTALLATION 3. With the visor up, align the rivets in the holes and screw them on each side of the helmet

LENS REMOVAL 2. Slightly open the arms of the visor to remove it from the helmet

HELMET

TECHNICAL MANUAL ALPINE 2020/21

HELMET TECHNOLOGY INDEX

135 summary <<<

HELMET

TECHNICAL MANUAL ALPINE 2020/21

CONVENIENCE

136

summary <<<

CONVENIENCE

CHINGUARD COMPATIBILITY

SKI & BIKE: DOUBLE STANDARD COMPATIBILITY

REF. L78869600 Chinguard Metal

Available on BRIGADE, SPELL & PACT HELMETS MODELS

Compatible with all sizes - S RACE - S RACE FIS INJECTED - S RACE FIS INJECTED JR

SKI USE Ski & summer liner included

BIKE USE Take out goggle retainer Take out ski liner

KEEP ONLY SUMMER LINER

AUDIO SYSTEM Available on : › Brigade+ Audio › Care and handling: The earpad sound system is built to handle cold, snowy conditions. However, this system is not waterproof. Do not submerge the Earpad or cord in water or any other liquid. Do not attempt to clean or to disinfect your helmet with the earpad sound system installed.

COMPATIBLE AUDIO SYSTEM

HELMET

Audio system compatible with all Salomon helmets, except : S RACE, S RACE SL, S RACE FIS INJECTED, S RACE FIS INJECTED JR, MTN Lab, Grom Visor, Grom. A pocket inside the removable earpad allows you to insert an audio system of your choice.

TECHNICAL MANUAL ALPINE 2020/21

› Warning: For use with Salomon snowsports helmets only. Headphones used in snowsports may cause the skier/rider to not hear other skiers/riders. This can lead to an accident and possible injury or death. Always stay in control. Skiers/Riders downhill from you always have priority, so it’s your priority to make sure you avoid them. Headphones will also restrict your ability to hear what your edge/edges are doing on the snow and may distract you. They may distract you from focusing on skiing or riding safely which may lead to less control.

137 summary <<<

GOGGLE SALOMON OPTICAL EXPERTISE

OPTICAL QUALITY GUARANTEE SALOMON GOGGLES PROTECT THE EYES FROM WIND, COLD, SNOW, AND MOST IMPORTANTLY, THE SUN. SUNLIGHT IS MADE UP OF THREE TYPES OF RAYS: ULTRAVIOLET, VISIBLE LIGHT, AND INFRARED. Salomon lenses all pass the European Standard (CE EN174:2001), indicating a safe level of sun protection. All Salomon lenses are tested in external certified labs, in-house labs, and in the field to assure that they meet Salomon standards for scratch resistance, adhesion, durability and longevity.

GOOD TO KNOW Salomon lenses have extra lens durability thanks to: • TRI-TECH: new generation of anti-static, hydrophobic and oleophobic coating improves its intrinsic qualities, without altering the color or tint, and ensures a super smooth, extremely durable coating. Available on S MAX & XT ONE Multilayer.

ANTISMUDGES

DECLARATION OF CONFORMITY EU declaration of conformity are available on www.salomon.com

ANTISTATIC

WATERREPELLENT

• ANTI-SCRATCH FINISHING: all Salomon lenses have an additional antiscratch finishing with high resistance and long-lasting durability.

GOGGLE

TECHNICAL MANUAL ALPINE 2020/21

CATEGORY AND VISIBLE LIGHT TRANSMISSION

138

PROTECTION INDEX OR CATEGORY

VISIBLE LIGHT TRANSMISSION *

80 to 100%

Little to no lens tint. These lenses are best in stormy weather conditions, very low light, or under artificial light (ski domes or in northern countries). They primarily protect against wind, snow and dust.

43 to 80%

Lenses with low or light tint, designed to enhance terrain contrast and definition in cloudy and medium (flat) light conditions.

18 to 43%

Lenses with medium tint, designed for universal use. These provide the best vision in most conditions, brighten details and increase depth perception. Ideal for flat to moderately sunny conditions.

8 to 18%

Fully tinted lenses for use in sunny conditions. They give exceptional visual acuity, color definition and glare protection for bright days and all sunny conditions.

3 to 8%

Maximally tinted lenses, typically reserved for use in extremely bright conditions, like glaciers or high altitude in snow. This category is not recommended for driving.

* This refers to the amount of visible light that can pass through a lens. For example a lens with a VLT of 12 % allows roughly 12% of visible light to pass through the lens (therefore blocking 88% of visible light). summary <<<

GOGGLE TECHNOLOGY INDEX

LENS

GOGGLE

TECHNICAL MANUAL ALPINE 2020/21

FRAME CONSTRUCTION

139 summary <<<

140

summary <<<

GOGGLE

TECHNICAL MANUAL ALPINE 2020/21

141

summary <<<

GOGGLE

TECHNICAL MANUAL ALPINE 2020/21

CHANGING LENS SYSTEM

S/MAX LENS REMOVAL

2. Lens is released

1. Press the top and bottom buttons located at the nose area

1. Press toptheand buttons 1. the Press topbottom and bottom buttons located at the at nose located the area nose area

LENS INSTALLATION

2. Lens released 2.isLens is released

GOGGLE

TECHNICAL MANUAL ALPINE 2020/21

1. Align the right lens clip to 1 area 1 in the frame its located

1. Align the right 1. Align the lens rightclip lenstoclip to its located area in the in frame its located area the frame

3. Align and clip the left lens clip to its located area in the frame

3. Align and clip leftthe lens its located area in the in frame 3. Align andthe clip leftclip lenstoclip to its located area the frame

142 summary <<<

2. Refold the lens on the frame

2. Refold the lens theon frame 2. Refold theon lens the frame

4. Simply press lens together in the central area

4. Simply press press lens together 4. Simply lens together in the in central area area the central

CHANGING LENS SYSTEM

LOFI

e lens on the frame

he lens on the frame

ns together rea

ens together area

1. Pull top of the frame and release the lens

LENS INSTALLATION

3 OK

1. Plug carefully the inside lens keys starting by the nose

3. Guide each key of the lens in their top keys holes

2. Guide each key of the lens in their bottoms keys holes

4. Clip the upper lens by inserting the inside key on the frame hole

TECHNICAL MANUAL ALPINE 2020/21

ens is released

1. Pull top of the frame and release the lens

4. Clip the upper lens by inserting the inside key on the frame hole

GOGGLE

ns is released

LENS REMOVAL

143 summary <<<

CHANGING LENS SYSTEM

XT ONE / X VIEW / S VIEW LENS REMOVAL

GOGGLE

TECHNICAL MANUAL ALPINE 2020/21

LENS INSTALLATION

144 summary <<<

CHANGING LENS SYSTEM

COSMIC LENS REMOVAL

GOGGLE

TECHNICAL MANUAL ALPINE 2020/21

LENS INSTALLATION

145 summary <<<

CHANGING LENS SYSTEM

FOUR SEVEN / AKSIUM / IVY / SENSE / TRIGGER / JUKE / KIWI

LENS INSTALLATION

GOGGLE

TECHNICAL MANUAL ALPINE 2020/21

LENS REMOVAL

146 summary <<<

ADVICES

USER GUIDE MAINTENANCE ADVICE

STORAGE ADVICE

TO CLEAN THE LENS, USE SOAPY WATER AND RINSE IT UNDER A STREAM OF LUKEWARM WATER. LEAVE IT TO DRY NATURALLY AND WIPE WITH A SOFT CLOTH. DO NOT USE ALCOHOL, DETERGENT OR SOLVENT. THESE SALOMON GOGGLES FEATURE AN ANTI-FOG TREATMENT. THE INSIDE FACE OF THE LENS IS SCRATCH SENSITIVE AND SHOULD BE TREATED WITH CAUTION. PLEASE AVOID WIPING IT. SNOW WHICH HAS PENETRATED THE GOGGLES SHOULD ONLY BE SHAKEN OUT.

WHEN DRY, STORE THE GOGGLES IN THEIR SPECIALLY DESIGNED COVER. AFTER A FALL OR A LONG PERIOD OF NON-USE, THE GOGGLES SHOULD BE CHECKED FOR DAMAGE TO THE LENS, THE FRAME, THE FOAM OR THE STRAP. DO NOT DRY THE GOGGLES NEAR A HEAT SOURCE AND AVOID EXTREME TEMPERATURES (IE NOT EXCEEDING 50Ë&#x161;C).

USAGE RESTRICTIONS AND ADVICE THESE GOGGLES ARE DESIGNED FOR WINTER SPORTS ACTIVITIES. THEY ARE NOT AN INDUSTRIAL SAFETY PRODUCT AND MUST NOT BE USED IN ROAD TRAFFIC. THEY PROTECT AGAINST BAD WEATHER AND UV RAYS BUT ARE NOT MEANT TO PROTECT AGAINST IMPACTS, HAZARDOUS RAYS OR CHEMICAL SUBSTANCES. TO AVOID FOGGING, DO NOT WEAR THE GOGGLES ON YOUR FOREHEAD. FOR A BETTER FIT, PLEASE ADJUST THE GOGGLE STRAP.

GOGGLE

TECHNICAL MANUAL ALPINE 2020/21

USE OF GOGGLES IMPLIES COMPLIANCE WITH THE INSTRUCTIONS AND THE LIMITATIONS CONTAINED IN THIS GUIDE.

147 summary <<<

POLE TECHNOLOGIES ALPINE POLES MAINTENANCE RECOMMENDATIONS

CHOOSING YOUR POLE SIZE - Turn the pole upside down with the tip pointing up. - Hold the pole right under the basket. - Your arm will form a right angle (90°) when you have the ideal size.

Use a cloth with soap and water to clean the poles. It is prohibited to use chemicals, hot water or pressurized water, gasoline, alcohol, detergents, solvents or aerosols that can permanently damage the plastic materials and erase the cosmetics.

RENTAL POLES - Salomon designed specific poles for rental adapted to a professional and intense use. - This warranty will not apply for damages resulting of rental use of poles that was not designed specifically for rental.

ALPINE POLES SIZING CHART

MOUNTING THE REPLACEABLE BASKETS Salomon has made 1 type of replaceable baskets available to you: A • Mounting: at the same time, screw the basket on and push it towards the handle of the pole. • Removing: at the same time, unscrew the basket and pull it toward the tip of the pole. B • Screw the basket on completely until you hear four clicks (wear gloves as a precaution).

SKIER'S HEIGHT (cm)

POLE LENGTH (cm) ALPINE

195 to 200

135

185 to 190

130

180

125

170 to 175

120

165

115

160

110

150 to 155

105

145

100

140

135

130

125

120

115

TECHNICAL MANUAL ALPINE 2020/21

SAFETY STRAP FOR SKETCHY SITUATIONS CLICKING AND UNCLICKING THE STRAP

Figure.8

Figure.3

Figure.2

Figure.4

Figure.6

Figure.3

Figure.5

Figure.6

Figure.7

Figure.9

POLE

AUTO RELEASE STRAP With tension adjustment

Adjust the tension using the tool provided according to how you ski and what your level is. The original setting is low. Adjust it according to how you ski and what your level is, while taking care not to overtighten it to allow the system to trigger.

Figure.6

Figure.8

AlpinSys t em CLICK0418 / - rjm

148 summary <<<

TO ADJUST THE TENSION Use the allen key tool provided with the pole

POLE TECHNOLOGIES ALPINE POLES TECHNICAL FEATURES COMPOSITE RANGE - We do our pole’s shafts the same way that golf companies do their own golf shafts. - We defined three levels of Carbon qrade:

NORDIC POLES HOW TO CUT AND GLUE POLES 1. Take off the Grip by soaking it in boiling water and then, simply removing it by hand.

5. Warm up some thermo glue by using a heatgun. And apply warm glue directly on the top of the shaft.

2. Put some tape exactly over the cutting zone.

6. Warm up again thermo glue on the shaft with the heat-gun. Place directly the grip on the shaft, taking care that it’s weel positioned compared to the basket. 3. Cut the shaft exactly where you need by using a saw, and cutting directly on the tape. This will enable the delamination of the carbon fiber.

15% of Carbon

POLE LENGTH (cm)

SKIER'S HEIGHT (cm)

CLASSIC

SKATING

195

165

175

190

160

170

185

155

165

180

150

160

175

145

155

170

140

150

165

135

145

160

130

140

155

125

135

150

120

130

145

115

125

140

110

120

135

105

115

130

100

110

125

105

120

100

115

110

105

100

POLE

4. Remove the tape and use sand paper to clean remaining dust of carbon.

80% of Carbon

NORDIC POLES SIZING 40% of Carbon CHART

TECHNICAL MANUAL ALPINE 2020/21

ALUMINIUM RANGE - Salomon know-how in aluminium is proven with bindinqs, ILS and Mavic wheels. - According to this experience, we defined three levels of strenqth

149 summary <<<

BACK PROTECTION SHAPE CHARACTERISTICS & SIZING CHART

WAIST TO SHOULDER

MEN MEN (CM) HEIGHT WAIST TO SHOULDER

XS 163-168 40-42,6

S 168-173 42,7-45

MEN (INCHES) HEIGHT WAIST TO SHOULDER

XS 5’4’’-5’6’’ 15.7’’-16.8’’

S 5’6’’-5’8’’ 16.8’’-17.8’’

M 173-178 45,1-48

L 178-183 48,1-51

XL 183-188 51,1-53

M L XL 5’8’’-5’9’’ 5’9’’-6’0’’ 6’0’’-6’2’’ 17.8’’-18.8’’ 18.8’’-19.8’’ 19.8’’-20.8’’

WAIST TO SHOULDER

BACK PROTECTION TECHNICAL MANUAL ALPINE 2020/21

WOMEN WOMEN (CM) HEIGHT WAIST TO SHOULDER

XS 156-161 39-41

S 161-166 41-43

M 166-170 43-45

L 170-175 45-48

WOMEN (INCHES) HEIGHT WAIST TO SHOULDER

XS 5’2’’-5’3’’ 15.4’’-16.1’’

S 5’3’’-5’5’’ 16.1’’-16.9’’

M 5’5’’-5’6’’ 16.9’’-17.7’’

L 5’6’’-5’8’’ 17.7’’-18.9’’

HEIGHT WAIST TO SHOULDER

JS 117-128 28-31

JM 129-140 31-34

JL 141-152 34-37

JXL 153-164 37-40

KIDS (INCHES) HEIGHT WAIST TO SHOULDER

JS 3’9’’-4’2’’ 11-12.2’’

JM 4’2’’-4’7’’ 12.2’’-13.4’’

JL 4’7’’-5’1’’ 13.4’’-14.6’’

JXL 5’1’’-5’4’’ 14,6’’-15.7’’

KIDS KIDS (CM)

150 summary <<<

WAIST TO SHOULDER

TECHNICAL MANUAL ALPINE 2020/21

NOTES

151

summary <<<

ARGENTINA Winners Productos Deportivos S.A. Av. Leandro N. ALEM 690 PISO 14C1001AAO BUENOS AIRES TEL: +5411 5256 5000 / FAX: +5411 5256 1616

DENMARK Amer Sports Denmark Aps Kokkedal Industripark 14 B, DK 2980 Kokkedal TEL: 45 455 655.30 / FAX: 45.455.655.31

ARMENIA SPORT TIME LLC Tel : +374 10 54 47 07

ESTONIA / LATVIA / LITHUANIA A & Tova Mustamaen Tee 50, Tallinn 10621 Estonia TEL: 37 265 188 99 / FAX: 37 265 188 90

AUSTRALIA Amer Sports Australia PTY LTD 18-20 Lakewood Boulevard, Braeside, Victoria 3195 TEL: 613 8586 6666 / FAX: 613 9587 2289 AUSTRIA AMER SPORTS AUSTRIA GÖLLSTRASSE 24, GRÖDIG 5082 TEL: +43 6246 391-301 / FAX: +43 6246 391-170 AZERBAIJAN Timsport Tel : +994125666092 BELARUSSIA Sport EleganceContact: Miatelski Ihar 78 Nezavisimosti Avenue, 220012 MINSK TEL: 375 172 840 244 / FAX: 375 172 840 244 BELGIUM / LUXEMBOURG Salomon Filiale France Metz-Tessy, 74996, Annecy Cedex 9 TEL: 0033.450.65.41.41 / FAX: 0033.450.65.42.61 BRASIL Winners Brasil Produtos Esportivos Ltda. Tel : +55 11 3094 1900 Fax : + 55 11 30941920 BULGARIA MTK Sport Ltd. Perzenk 1B Street 1407, Sofia Bulgaria TEL: 359 888 343 427 / FAX: 359 294 769 85 CANADA Salomon Canada 2700 14th Avenue, Markham, ON L3R 0J1 TEL: 905 470 9966 / FAX: 905 944 4651 CHILE GRYLAN S.A. Tel : +562 2949 3717 www.grylan.cl CHINA AmerSports China 6F, BEA Finantce TowerNo.66 Hua Yuan Shi Qiao Road Shanghai, China 200120 Tel: +86-21-5116-5288 / FAX: +86-21-5116-5299 COLOMBIA Outdoor Tech Int. Tel : + 57 1 218 9045 CZECH REPUBLIC Amer Sports Czech Republic s.r.o / V Chotejne 700/7/102 00 Praha 10 CZECH REPUBLIC TEL: (+420) 272 700 963

FINLAND Salomon Sport Finland Oy Mäkelänkatu 91, FI-00610 Helsinki TEL: 358 (0) 207 789 600 / FAX: 358 (0) 207 789 618 FRANCE Salomon France/ Amer Sports France 80 rue Condorcet BP128, 38090 VAULX-MILIEU TEL : +33 474 99 15 15 GEORGIA DV Sport LTD 0102 Toidze St. 2/10, 0102 TBLILISI, GEORGIA TEL: (+995) 77 99 11 22 GERMANY Amer Sports Deutschland GMBHParkring 15-17, 85748 Garching, Germany TEL: 49 89 321 987 0 / FAX: 49 89 321 987 26 GREAT BRITAIN Amer Sports UK First Floor Theta Building, Lyon Way Frimley, Surrey GU16 7ER, England TEL: +44 1276 404 800 GREECE Hellenic Flame S.A. 38-40, 26th Octovriou str. GR-546 27 Thessaloniki Greece TEL: 0030 2310 566269 / FAX: 0030 2310 500826 HONG KONG Orient Fair Development Ltd. Tel : (852) 2410 1952 Fax : (852) 2418 0544 HUNGARY Salomon Hungary TEL: 36 1 4511 492 / FAX: 36 4 4511 401 ICELAND Prosport ehf. Tel : +354 663 0707 Fax : +354 552 8987 INDONESIA PT Primer Globalindo Tel : (62-21) 2942 7761 IRAN NIK General Trading LLC Tel : +971 4 359 87 80 Fax : +971 4 359 28 21 ISRAEL MASAI Israel 2009 Ltd Tel : +972 3 699 2200 Fax : +972 3 699 6613 ITALY AMER SPORTS ITALIA Spa Via Priula 78 31040 Nervesa della Battaglia (TV) TEL: 39 0422 529110 / FAX: 39 0422 529199

ISRAEL DV Sport LTD 0102 Toidze St. 2/10, 0102 TBLILISI GEORGIA TEL: (+995) 77 99 11 22 JAPAN Amer Sports Japan,Inc Shinjuku East Side Square 6F, 6-27-30 Shinjuku, Shinjuku-ku, Tokyo 164-0022 JAPAN TEL: +81 3 6831 2700 / FAX: +81 3 6831 2721 KAZAKHSTAN Office Union Space 1, Amir Temur Street 100084 TASHKENT UZBEKISTAN TEL: (+998) 71 232 4440 / FAX: (+998) 71 232 4446 KYRGYZTAN Shahzada Maret Abdraimovna Appart 23 – HO USE 16, Microrayon 4, 720000 BISHKEK TEL: (+996) 772 545 610 KOREA Salomon Korea Business Unit (Amer Sports Korea Ltd) 2F Namdo Bldg.53-4 Cheongdam-dong Kangnam-ku, Seoul, Korea TEL: 82 2 518 0781 / FAX: 82 2 547 5464 LEBANON Sports Experts Co. Faraya Kesrouan, PC278 Zouk Mikael Lebanon TEL: 961 37 72 555 / FAX: 961 93 21 312 MACEDONIA VRM Kuzman Josifovski Pitu, 15-3 / 171000 Skopje TEL: 389 2 462 345 / FAX: 389 2 464 790 MALAYSIA Suite 19.01, 19th Floor, Menara IGB, The Boulevard, Mid Valley City Lingkaran Syed Putra 59200 Kuala Lumpur TEL: +603 2282 0009 FAX: +603 2287 6541 MAURITIUS Emcar LTD Old Moka Road Bell Village, PORT-LOUIS MAURITIUS TEL: (230) 208 6335 / FAX: (230) 212 5952 MONGOLIA Ayanchin outfitters LLC Seoul street 21, 21062 Ulaanbaatar Mandah Karlsen TEL: 976-11 31 92 11 / FAX: 976-70 11 26 12 NETHERLANDS Salomon Netherlands B.V. T.A.V. Boaz Bego Plesmanstraat 1 A 28 3833 LA Leusden TEL: 00 31 33 434 5700 / FAX: 00 31 33 434 5719 NEW CALEDONIA La Licorne 60 Rue Gervolino Magenta BP 299798846 NO UMEA Cedex NEW-CALEDONIA TEL: (687) 285 198 / FAX: (687) 272 336

Front cover: ©Christoffer Sjostrom - Photos: Fabrik d’Images, Studio E. Bergoend, P. Toeroek, S. Deslandes, J.M. Favre, Scott Markewitz , J.L. Michon, C. O’Connel, Pentaphoto, Zoom - © SALOMON 2019. RCS Annecy B 325 820 751. S.A. à Conseil d’Administration. This document is not contractual. SALOMON reserves the right to modify or discontinue any product. Every product not available in all countries. All rights reserved.

SalomonSports.com

NEW ZEALAND Snoworld Sports 304 Cashel street, Christchurch New Zealand TEL: 03 366 1122 / FA X: 03 379 5099 NORWAY Amer Sport Norge A/S Eyvind Lyches Vei 9C N-1338 Sandvika (PB 293, 1301 Sandvika) TEL: 47 67 55 13 30 / FAX: 47 67 55 13 31 PHILIPPINES Uniglobe Travelware Co., Inc Tel : (632) 3031234 POLAND Amer Sports Poland Sp.Z O.O. 31-323 KRAKÓW, Ul.Pilotów 2 TEL:48 12 349 47 00 / FAX: 48 12 349 08 01 REUNION 47 Rue du Lagon, 97436 Saint Leu TEL: 02 62 34 97 31 ROMANIA Master Sport SRL Dr.Russel Street Nr 4, Bucuresti TEL: 0040-31 405 07 52 / FAX:. 0040-31 405 07 53 RUSSIA ZAO “Amer Sports” Leninskiy r-n, Kaluzhskoe shosse 21km Megamall, of 208, 142704, Russia, Moscow Region TEL: +7 495 6412646 / FAX: +7 495 6412645 SERBIA / MONTENEGRO / KOSOVO Fitex D.O.O. Bilevar Arsenija Carnojevica 97/a, Novi Beograd - 11070 TEL: 381 11 311 6266 / FAX: 381 11 311 5645 SINGAPORE VGO Corporation Limited Tel : +65 6543 5800 SLOVAKIA Amer Sports Slovakia Hattalova 12/A, 83103 Bratislava, SLOVAKIA TEL: +421-2-44640011 SLOVENIA DASAL d.o.o. Tržaška 132, 1000 Ljubljana TEL: 00386 1 7566 074 / FAX: 00386 1 7566 073 CROATIA/BIH Amer Sports Austria GmbH Tel : +386 404 12 709 SOUTH AFRICA Trail Terrain Sports C.C 21/25 Churchill Rd, Umgeni, 4001 DURBAN SOUTH AFRICA TEL: (27) 313 13 14 75 / FAX: (27) 313 13 14 76 SPAIN , ANDORRA, PORTUGAL Amer Sports Spain S.A. Parque de Negocios Mas Blau II, C/ Conca de Barberà, 4-6. 08820 El Prat de Llobregat, Barcelona , España TEL: +34 93 262 5100; / FAX: +34 93 262 5101

SWEDEN Amer Sports Sverige AB Åsboholmsgatan 16, 504 51 Borås TEL: 46 33 23 37 00 / FAX: 46 33 23 37 40 SWITZERLAND AMER SPOR TS SA - Salomon Bachtalen 33, CH-6332 Hagendorn TEL: 41.41.784.12.12 / FA X: 41.41.784.12.13 TAIWAN Starlike International Ltd. Tel : (886) 2-8751-5235 Fax : (886) 2-8751-5652 THAILAND Action Perfect Co., Ltd. Tel : (662) 642-2993-5 Fax : (662) 642-2996 TURKEY CMS Sport / Yesilyurt Mah. Sipahioglu Cad. Ekin Sok, Sandikci Apt. N° 20/7 34149 BAKIRKOY / ISTANBUL / TURKEY TEL: (+902) 125 743 090 / FAX: (+902) 126 633 583 UKRAINE 30/39 Shchekavitskaya Str.,office 261, Kiev, 04071 TEL: +38 044 207 12 01 / FAX: +38 044 207 12 02 UAE & G.C.C GCC Nik trading co. (L.L.C) P.O. Box 111549, DUBAI-UAE TEL: 97 14 359 87 80 / FAX: 97 14 359 28 21 EMAIL: info@niktrading.com AMERICAS Amer Sports winter and outdoor Americas Tel : +18016247500 Fax : 18013344500 LATIN AMERICA Amer Sports Latin America Av. Santa Fe 495, Piso 15, Int. 1501, Col. Cruz Manca 05349 MEXICO CITY, D.F. C.P. TEL +52 55 9177 9100 FAX +52 55 9177 9101 EMERGING MARKETS: EASTERN EUROPE , MIDDLE EAST, AFRICA Salomon SA Metz-Tessy, 74996 Annecy Cedex 9, France TEL: 33.450.65.40.97 / FAX: 33.450.65.44.02 DOM - TOM Laurent Allart Tel : +33 6 92 64 62 03 Fax : +33 2 62 34 97 31 UNITED STATES SALOMON USA 2030 Lincoln Ave., Ogden, UT 84401 TEL: 800 225 6850 USHUAIA / TIERRA DEL FUEGO POPPER S.A Tel : +54 2901 422244

Salomon Tech Manual Alpine 2020/21

Articles inside

GUARDIAN MNC BINDING - Backcountry

WARDEN MNC 13 DEMO BINDING

WARDEN MNC 13 BINDING

S LAB SHIFT MNC 10 & 13 BINDING

X12 TL GW & X14 TL GW

WARDEN MNC 11 DEMO BINDING

WARDEN MNC 11 BINDING

EASYTRAK PLATE WITH L10 GW BINDING

LEISURE TRAK PLATE WITH M10 GW & M11 GW BINDINGS

JUNIORTRAK PLATE WITH C5 GW BINDING

N L7 GW BINDINGS

EASYTRAK PLATE WITH Z11 GW & Z10 GW BINDING

N C5 GW 2BINDINGS

WARDEN 11 DEMO BINDING

WARDEN 11 BINDING

EASYTRAK PLATE WITH MERCURY BINDING

EASYTRAK PLATE WITH LITHIUM BINDING

X TRACK PLATE WITH XT BINDING

SPEED PLATE + Z BINDING

X12 & X16 BINDING

X12 TL & X14 TL BINDING

SMARTRAK BINDING

LIGHTRAK PLATE J L & H L BINDING

SMARTRAK GRIP / GRIP PLUS BINDING

SYNCHRO CENTER AND SYNCHRO RENTAL BINDING